Related
Hi, because with last update increased count of people with bricket phone, I just tryed search for way how to repair this phone. It seems, that last possible way how to save your phone is emergency mode.
I would like to notify you, that I didn't tested it (I'm had not luck enough to brick my phone yet ). I just searched and tried write this for help to others.
So, let's go on.
1) If it's not possible connect to phone via ADB (in Adroid SDK/tools run "adb shell") at all you will try next steps. If it will work, you can use another, verified tools like custom recovery or KDZ_FW_UPD (search on forum for more) [HOWTO] Flash original firmware on P500, )
2) If you fail in previous step, you can try enter into emergency mode manually and try to flash ROM with KDZ_FW_UPD:
Download KDZ updater and uncompress it
http://www.4shared.com/file/UleS4dP3/KDZ_FW_UPD_EN.html
Install msxml.msi from the uncompressed directory
Charge your battery to almost full state (I'm not sure, but it can be reason if phone doesn't start)
Turn phone off somehow (remove battery etc.)
Install drivers properly
Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments
Install the LG drivers by selecting the update manager from the lg site
Disable LGE Virtual Modem. In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.
Press and keep pressed "Volume up"+"Return" and connect USB cable to phone
Yellow screen with text emergency mode should appeared
Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
Run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT (I have one report that CDMA mod works too)
Select PhoneMode : DIAG (in case of fail try EMERGENCY, and as last chance use CS_EMERGENCY)
I Recommend do not switch phone off. There was some people, which done it and after they were not be able to turn it on again. If flashing failed, just select some another mode and try it again, again, try shake/connect disconnect, again, again....
In KDZ file : Choose the ROM file you downloaded in the first step
Press Launch software update
Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
Make sure that all update was done successfully. Phone should restart itself automatically
Disconnect the USB cable from the phone
Press the three button combo for HW reset of device i.e volume up + home + power button
List to do based on Zecanilis's [HOWTO] Flash original firmware on P500
3) Still no success? Wait for more "What I can do" or just go to LG and let repair on them.
Source:
http://forum.gsmhosting.com/vbb/f282/vygis-shell-v1-1-0-josedavido-1166478/ (included file named "Flash help.txt" in application)
http://android.modaco.com/content/l...modaco-com/321895/faq-gt540-reference-thread/
Please let me know if it works. I just searched for way and I haven't possibility to test this steps for now. I will do update if it will be necessary, same as I will try describe more about software which I founded.
Some experiences from thread(s):
AVanover5: ...It works if you set the mode to CDMA and DIAG. Just to let people know. Not sure if it'd work without the recovery screen or not. I never tried it ironically, haha. Thank you guys.
geejay2: ...Bricking seems to be easily achieved by forgetting to disable the LG Modem driver. Apparently the modem driver interferes during flashing. Also I noted that kdz is not stable under Win2k, I switched to WinXP to flash successfully. I saw several aborted flashing attempts in WinXP with modem driver enabled.
domenic_s:KDZ_FW_UPD doesn't work (Application cannot start) -.- Using Windows 7 64bit version. //edit: allright tried another pc (win xp 32bit) and yeah - it worked... I'm so happy.
Click to expand...
Click to collapse
About shaking (sorry, but I still can't believe... )
salte_eskil:wow! shaking the phone really worked! seems kind of stupid but thanks to you all at the xda forum for tips and tricks
4wd vege: Now unbricked. Strangely kdz updater only saw my phone after shaking!!!
me2kimi:It sound crazy to shake the phone while at emergency mode. I's crazy but it magic. ...So what I do is connect to usb, Launch software update at kdz while shaking the phone. Then after that kdz is working like normal.
Click to expand...
Click to collapse
I tried with all possible combination.. with and without battery.. vol- home, vol + return, power vol+ home.. end more.. but phone don't turn on...
In meantimes the phone is in the service LG.. hope...
Exscuse me for my English
Did you had phone off before trying this? And also battery should be charged. I just added this things...
If event that it not show you emergency mode, LG service and warranty is probably the only way how to proceed. Sorry. But I will be searching if another way will exist...
Good work .. I hope that you will find a way to solve ... especially for other users .. good luck
Good work @The_ERROR.
It should work. I think you should also add that the phone mode should be set to Emergency (and not DIAG as mentioned) in the kdz updater.
Moved to development and stickied it for a while!
Thank you!
Cheers
socialdistortion said:
Good work @The_ERROR.
It should work. I think you should also add that the phone mode should be set to Emergency (and not DIAG as mentioned) in the kdz updater.
Click to expand...
Click to collapse
Good to know - do you know differences between CS_EMERGENCY and EMERGENCY?
Recovery Phone?!
Hello,
Had anyone tried "Recovery Phone" from the LGMobile Update app? It's under the "Customer Support" menu. Enter IMEI or S/N and see if it can bring it up to life.
Cheers.
Yes.. I tried.. but nothing.. the LG MOBILE UPDATE crashed because don't wiew the phone in Usb...
zeule said:
Hello,
Had anyone tried "Recovery Phone" from the LGMobile Update app? It's under the "Customer Support" menu. Enter IMEI or S/N and see if it can bring it up to life.
Cheers.
Click to expand...
Click to collapse
I can add that as next possible way Let me expect it.
batman89i said:
Yes.. I tried.. but nothing.. the LG MOBILE UPDATE crashed because don't wiew the phone in Usb...
Click to expand...
Click to collapse
So... it sad everything
The_ERROR said:
Good to know - do you know differences between CS_EMERGENCY and EMERGENCY?
Click to expand...
Click to collapse
Not really. Gathered some info though. We use emergency mode when the phone boots into only emergency mode else we try CS emergency as last option.
In any case this method will work only if the kdz updater recognises the phone.
Further reading http://android.modaco.com/content/lg-gt540-optimus-gt540-modaco-com/321895/faq-gt540-reference-thread/
I was able to do the KDZ, actually thats the only way possible. Please add this to the list:
1. Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments.
2. Install the LG drivers by selecting the update manager from the lg site.
3. Disable the modem driver.
4. Once done, reboot the handset and when it has come to emergency mode connect it via USB.
5. Its going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
6. shake the handset - IT DID WORKED FOR ME.
My suggestion don't give up. It took me around 14 hours to bring the handset back to original firmware and here I am today trying to boot the rom once again.
7. UPDATE AND ENJOY.
pariksheetsharma said:
I was able to do the KDZ, actually thats the only way possible. Please add this to the list:
1. Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments.
2. Install the LG drivers by selecting the update manager from the lg site.
3. Disable the modem driver.
4. Once done, reboot the handset and when it has come to emergency mode connect it via USB.
5. Its going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
6. shake the handset - IT DID WORKED FOR ME.
My suggestion don't give up. It took me around 14 hours to bring the handset back to original firmware and here I am today trying to boot the rom once again.
7. UPDATE AND ENJOY.
Click to expand...
Click to collapse
Thanks, I will do!! Only about 4 and five.
First reboot the handset and when it has come to emergency mode connect it via USB
and then
It's going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
So, whats about if phone didn't go into emrgency itself (for example stuck on Android logo)?
The_ERROR said:
Thanks, I will do!! Only about 4 and five.
First reboot the handset and when it has come to emergency mode connect it via USB
and then
It's going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
So, whats about if phone didn't go into emrgency itself (for example stuck on Android logo)?
Click to expand...
Click to collapse
I am talking about phone getting into Emergency mode, KDZ doesn't need to switch to CS_EMERGENCY or EMERGENCY Switch off the phone first, then you are either connect it to USB cable or you can remove it from the USB cable. Key combination to bring the phone only in emergency mode are:
1. Connected to USB cable, only thing visible is the LG logo, this is because its getting charged. Press VOL UP + BACK BUTTON
2. Not connected to USB cable and is not charging and so switched off: Press VOL UP + BACK BUTTON + POWER BUTTON
In both the cases phone will switch to a yellow screen showing: "Emergency mode!!" and will remain like that.
It's only in Emergency mode that the handset will be detected like a USB drive and can be KDZed.
I seriously doubt the "Shake your phone part". It just sounds so ...
Peace
pariksheetsharma said:
I am talking about phone getting into Emergency mode, KDZ doesn't need to switch to CS_EMERGENCY or EMERGENCY Switch off the phone first, then you are either connect it to USB cable or you can remove it from the USB cable. Key combination to bring the phone only in emergency mode are:
1. Connected to USB cable, only thing visible is the LG logo, this is because its getting charged. Press VOL UP + BACK BUTTON
2. Not connected to USB cable and is not charging and so switched off: Press VOL UP + BACK BUTTON + POWER BUTTON
In both the cases phone will switch to a yellow screen showing: "Emergency mode!!" and will remain like that.
It's only in Emergency mode that the handset will be detected like a USB drive and can be KDZed.
Click to expand...
Click to collapse
OK, I edited it. But I kept possibilities of EMERGENCY and CS_EMERGENCY modes if standard way failed. About switch into emergency, I think that it does not matter which way for emergency is used.
socialdistortion said:
I seriously doubt the "Shake your phone part". It just sounds so ...
Peace
Click to expand...
Click to collapse
Yes, I know... but if it will help, it doesn't matter how stupid it sounds....
Stuck in LG logo, unable to boot into emergency mode.
What can I do? Go to LG?
cjbi said:
Stuck in LG logo, unable to boot into emergency mode.
What can I do? Go to LG?
Click to expand...
Click to collapse
Have you tried all the mentioned methods? Press the combination buttons a little longer (Maybe that can help).
BTW what did you do that bricked your phone?
My LG D605 does not boot and I have a black screen. Before brick i go via ADB to recovery on official KK. Mobile is dead USB dont work
I have the same problem help!!!
LoToR122 said:
My LG D605 does not boot and I have a black screen. Before brick i go via ADB to recovery on official KK. Mobile is dead USB dont work
Click to expand...
Click to collapse
No responses to Emergency mode flashing by KDZ?
Try at least with HARD RESET... Hold Power Key + Volumen Down key + Home key
When LG logo appears, release all the keys! Good luck!
LoToR122 said:
My LG D605 does not boot and I have a black screen. Before brick i go via ADB to recovery on official KK. Mobile is dead USB dont work
Click to expand...
Click to collapse
Give me a pm when you have 1 hour I might have an idea to save you.
christi9503 said:
Give me a pm when you have 1 hour I might have an idea to save you.
Click to expand...
Click to collapse
Can you help me? pls
kikobuendia said:
I have the same problem help!!!
Click to expand...
Click to collapse
First, there is no such thing as hardbrick (not anymore, most modern phones cant be hardbriked )
Be sure, u have all the drives and whatnots installed in the copmuter !
from: http://forum.xda-developers.com/showthread.php?t=2730501
[Q] How to install a .kdz?
[A] (Tutorial thanks to @[W]ar[H]ead, confirmed working by TaZRAge)
#1) First to get into download mode:
1. Remove battery
2. Put usb to computer and phone (w/o battery)
3. Hold "Vol up" button
4. Put battery back
You will get into download mode (aka emergency mode).
#2) Unpack kdz flasher, and install msxml.msi.
#3) Run KDZ_FW_UPD.exe set "type" to 3GQCT and "phonemode" to DIAG.
#4) Choose the .kdz file to flash. Download link is under the "Downloads"
#5) Click "Launch software update" and wait. Phone must be connected in download mode(!). KDZ installer might get stuck but DO NOT disconnect it. (Unless it stays that way for a hour as a example)
NOTE: .kdz is a .kdz, you cannot extract it. If you get a .zip from the LG .kdz site you did something wrong.
Cisf said:
First, there is no such thing as hardbrick (not anymore, most modern phones cant be hardbriked )
Be sure, u have all the drives and whatnots installed in the copmuter !
from: http://forum.xda-developers.com/showthread.php?t=2730501
[Q] How to install a .kdz?
[A] (Tutorial thanks to @[W]ar[H]ead, confirmed working by TaZRAge)
#1) First to get into download mode:
1. Remove battery
2. Put usb to computer and phone (w/o battery)
3. Hold "Vol up" button
4. Put battery back
You will get into download mode (aka emergency mode).
#2) Unpack kdz flasher, and install msxml.msi.
#3) Run KDZ_FW_UPD.exe set "type" to 3GQCT and "phonemode" to DIAG.
#4) Choose the .kdz file to flash. Download link is under the "Downloads"
#5) Click "Launch software update" and wait. Phone must be connected in download mode(!). KDZ installer might get stuck but DO NOT disconnect it. (Unless it stays that way for a hour as a example)
NOTE: .kdz is a .kdz, you cannot extract it. If you get a .zip from the LG .kdz site you did something wrong.
Click to expand...
Click to collapse
You don't know what you are saying. You can HARDBRICK ANY modern device. By definition hardbrick means phone won't turn on won't respond and in some cases recognized as usb when connected to pc as usb bulk or qcom usb. etc. You damage the second bootloader and tell me what happens. You will see what you get.
christi9503 said:
You don't know what you are saying. You can HARDBRICK ANY modern device. By definition hardbrick means phone won't turn on won't respond and in some cases recognized as usb when connected to pc as usb bulk or qcom usb. etc. You damage the second bootloader and tell me what happens. You will see what you get.
Click to expand...
Click to collapse
first this is offtopic. Second, u are wrong ! Unless the phone is pshisicaly damaged (misfuctioning components or damaged), u cant hardbrick the phone with uploading different soft. on it (unless u change voltages and overclok, if that is possible on the device). Ofecourse they are exceptions, but all major modern manufactors, make hardbrick proof devices. Also, how exactly would u modify the emergency mode, and more important even if you could, why wold u do it !?
More on to the topic, none of the operations of rooting, bootloader installing, kdz install or CMx install , gets near the emergency mode. It remains intact.
Just retry all normal steps for installing kdz or recovery again, check the cables, all drivers on pc, and is best to have a charged phone battery.
EDIT: @kikobuendia
i found this post, same operations as mentioned in first reply, but more detailed:
http://forum.xda-developers.com/opt...optimus-l9-ii-lg-d605-unroot-unbrick-t2964693
Cisf said:
first this is offtopic. Second, u are wrong ! Unless the phone is pshisicaly damaged (misfuctioning components or damaged), u cant hardbrick the phone with uploading different soft. on it (unless u change voltages and overclok, if that is possible on the device). Ofecourse they are exceptions, but all major modern manufactors, make hardbrick proof devices. Also, how exactly would u modify the emergency mode, and more important even if you could, why wold u do it !?
More on to the topic, none of the operations of rooting, bootloader installing, kdz install or CMx install , gets near the emergency mode. It remains intact.
Just retry all normal steps for installing kdz or recovery again, check the cables, all drivers on pc, and is best to have a charged phone battery.
EDIT: @kikobuendia
i found this post, same operations as mentioned in first reply, but more detailed:
http://forum.xda-developers.com/opt...optimus-l9-ii-lg-d605-unroot-unbrick-t2964693
Click to expand...
Click to collapse
I am not gonna reply again but I am just saying you have no idea. Do not talk unless you are sure you can hardbrick any device with just root and just writing on second bootloader partition. Read about it if you don't know. Do not argue about it.
I can't get into download mode
kikobuendia said:
I can't get into download mode
Click to expand...
Click to collapse
Then that's a hard brick pretty much. Pull the battery out and connect the phone to PC. Tell me if it gets recognized.
EDIT: OFC wait like 6 seconds then put it back and after that connect to USB.
When i connect it pc makes a sound
kikobuendia said:
When i connect it pc makes a sound
Click to expand...
Click to collapse
I don't care if it makes a sound or not it's like it gets recognized? Look into device manager.
christi9503 said:
I don't care if it makes a sound or not it's like it gets recognized? Look into device manager.
Click to expand...
Click to collapse
Yes but flashtool doesnt recognize it
kikobuendia said:
Yes but flashtool doesnt recognize it
Click to expand...
Click to collapse
If you want to get this fixed just listen to me. It won't work like this tell me the answers to my questions and we might solve your problem. What is your device recognized as. Make me a screenshot of device manager if you can't explain.
neutrondev said:
Then that's a hard brick pretty much. Pull the battery out and connect the phone to PC. Tell me if it gets recognized.
EDIT: OFC wait like 6 seconds then put it back and after that connect to USB.
Click to expand...
Click to collapse
I have the same probalem, cant get to download mode, when i connect to pc it recognise it in hs usb qdloader 9008, any solutions to fix it. I flashed wrong .tot file.
did you managed to unbricked it?
I have the same probalem, cant get to download mode, when i connect to pc it recognise it in hs usb qdloader 9008, any solutions to fix it. I flashed wrong .tot file.
Click to expand...
Click to collapse
No, no luck yet. Seems to be impossible.
I connect to this post cuz my d605 is also facing a similiar issue, no system, no recovery, no adb, download mode worked only twice, for the rest, only emergency mode works, phone cannot even charge.
Phone is recognized from pc, I uninstalled modem drivers but stays in Emergency only few seconds then it shuts down (not sure if its the battery, since it doesn't charge as well). It shuts down actually at the moment that LG mobile support tool seems to recognize it.
It worked couple of times, phone was keeping staying in emergency mode for the beginning of the procedure but at the moment it need to put the kdz into the phone, the phone die.
The two times download mode worked, same, just shutting down immediately. This with LG support tool or LG flashtool2014.
KDZ_FW_UPD worked the first time after install and then doesn't run anymore, on two different Win10 machines.
I have no idea how to come out of this nightmare, just want to flash it :/
Ag0n1a said:
I connect to this post cuz my d605 is also facing a similiar issue, no system, no recovery, no adb, download mode worked only twice, for the rest, only emergency mode works, phone cannot even charge.
Phone is recognized from pc, I uninstalled modem drivers but stays in Emergency only few seconds then it shuts down (not sure if its the battery, since it doesn't charge as well). It shuts down actually at the moment that LG mobile support tool seems to recognize it.
It worked couple of times, phone was keeping staying in emergency mode for the beginning of the procedure but at the moment it need to put the kdz into the phone, the phone die.
The two times download mode worked, same, just shutting down immediately. This with LG support tool or LG flashtool2014.
KDZ_FW_UPD worked the first time after install and then doesn't run anymore, on two different Win10 machines.
I have no idea how to come out of this nightmare, just want to flash it :/
Click to expand...
Click to collapse
well, sorry for not replying earlier. My phone was on guarantee for about 2 months after I wrote the post. I just send it to LG Hellas via the e-shop I bought it from and in about 2-3 weeks, I had my D605 back like it was brand new. I searched a lot about my D605 hard bricked and I found that it is not fixable. My phone could not go into download mode though, as yours. Hope I helped you even a lil bit. Sorry for my bad English.
Hi, I was looking everywhere since yesterday but can't find a solution. I had cwm + twpr + lollipop cm12. I've decided to back to stock, so as allways: driver, b2cApp, kdz, v20h and v10a, usb, s/w mode, xml parser, shhtp, etc... Standard offline kdz method. But during flashing I stuck on 15% and get the info that my phone anad pc are not connected by usb cable, I tried changing usb ports at pc, reinstaling everything, but I have still the same error. If that woldn't be much enough I ****ed something up and I think I don't have any recovery right now
I can put my phone in s/w mode but I stuck on 15% with usb not connected error.
I can put my phone in fastboot mode but my pc does not recognize it, its just pluging in and out it from windows.
I can put my phone in stuck on LG logo 'mode'
Any help? How to unbrick it? How to flash stock or at least some custom recovery? Of course unlocked bootloader. Please help me :crying:
Key it ****ed up even more.
When kdz show me to connect my cable i clicked retry, plugen cable out and in, kdz found my device, and go to step 2. In half way I had again the same error, so again clicked retry, plug out, plug in. Again founded my device, when I had downloaded 100%, same situation. founded my device, log that tool is extracting kdz and nothing. Waiting about ~1,5h, nothing happend, so I diconected cable. In that moment kdz go to third step and I get windows force close for not repodnig app kdz. I said a loud **** and started again. Phone has not been found anymore by kdz. After a few tries, booted to fastboot, and connected to computer. It has been found as Google Fasbtoo USB, no way to update driver to fastboot. I disconected phone and decided to try again with s/w but nope. S/W not turning on anymore (with or without battery). Fastboot not turning on any more. Just LG logo, when I'm connecting device to PC it is sometging pluging in and out but nothing showing in device manager
Any ideas? Please!
I have the SAME problem with my (now old) LG... I read more than 20 tutorials for getting back to stock and nothing
Sent from my GT-I9205 using XDA Free mobile app
I triend on clen frsh windows I get OMAP device, fastboot is finding my device but wont start fastboot mode in my phone, when trying to flash cwm I get security error and still no s/w mode So I'm affraid that we have to say goodbay to our L9
What's more:
1. Can't find orginal p760 recovery, tried to flash p769 and I get wird effect, after LG logo screen looks like broekrn, some color stripes and all display going to white, then turn off.
2. Using fastboot and choosing options wit u-boot making my phone turning to LG logo with no security error, still no s/w, fastboot or recovery mode.
3. Using option 1 (1. Fastboot) from the fastboot tool is making my phone turnig black screen and nothin more, no even LG logo.
Please can anyone help us?
As I was trying to flash global rom via miflash, It gave an error at %50 helloblabla and stuck at nowhere. Just red led blinking. When I connect it to the pc, It is seen as diagnostics 900e (com10). I hold volume + and - and plug the usb cable after taking out battery and usb cable for 10 seconds and putting them back from back but It doesn't work. I cannot see my device in miflash to flash the device.
Use the deep flash method mentioned here
http://en.miui.com/forum.php?mod=viewthread&tid=310325&extra=page=1&page=1&mobile=2
Had the same issue on my rn3 and was able to recover it using this method(when test point seemed the only option). You just need a copper wire strand to do this. Short the usb 2nd pin as in the video, then remove cable and reinsert. Phone will be detected as unknown device, then update driver and phone will be shown as qdownloader 9008 mode. Next open miflash and flash rom.
tuxing said:
Use the deep flash method mentioned here
http://en.miui.com/forum.php?mod=viewthread&tid=310325&extra=page=1&page=1&mobile=2
Had the same issue on my rn3 and was able to recover it using this method(when test point seemed the only option). You just need a copper wire strand to do this. Short the usb 2nd pin as in the video, then remove cable and reinsert. Phone will be detected as unknown device, then update driver and phone will be shown as qdownloader 9008 mode. Next open miflash and flash rom.
Click to expand...
Click to collapse
See, the person I bought the phone will do it for me. That's not something I want to do.
Use the modified fastboot to reboot to edl from fastboot. google "fastboot edl"
justinxfan said:
Use the modified fastboot to reboot to edl from fastboot. google "fastboot edl"
Click to expand...
Click to collapse
I wish I could go in fastboot mode Device doesn't turn on at all. It needs deep flashing as I can learn. Will do it soon today.
I bricked my metro n200 5g and can't boot into EDL mode.
I can access fastboot and tried rebooting from there but it gave me an error saying "fastboot: usage: unknown reboot target edl"
How can i unbrick my phone?
red5815 said:
I bricked my metro n200 5g and can't boot into EDL mode.
I can access fastboot and tried rebooting from there but it gave me an error saying "fastboot: usage: unknown reboot target edl"
How can i unbrick my phone?
Click to expand...
Click to collapse
Hi red5815,
Are you certain you can't boot into EDL mode? Try the procedures below and let me know If you still can't enter into EDL mode.
Note: Make sure you have all of the necessary USB drivers installed (So your PC can recognize the connected device when it is connected to EDL mode)
First Method
Turn off your device
If you are in CrashDump Mode, I think you must hold down the power and volume up buttons for around 8-10 seconds (Until the screen goes off)
Then, hold down the volume up and volume down buttons simultaneously, and your device should enter EDL mode
While holding down both volume keys, connect your device to your PC via a USB cable
Your device should be recognized
Release the volume keys and press the "Start" button on MSM Tools (This will wipe your entire device, and if the bootloader was unlocked, it will relock it)
Second Method
Start MSM Tools and wait for the "waiting for device" message to appear (Before you start, keep in mind that this process will erase your whole device and relock the bootloader if it was previously unlocked)
Turn off your device and connect one end of the USB wire to your PC
Then connect the opposite end of the cable to your device
For a few seconds, press and hold the volume up, volume down, and power keys simultaneously
Your device should be recognized, and the flashing process should be started
Edit: Added proper warnings
pressing and holding the volume buttons only make it boot to fastboot.
red5815 said:
pressing and holding the volume buttons only make it boot to fastboot.
Click to expand...
Click to collapse
Hi red5815.
It takes a few attempts to get it right. Just make sure that all of the correct drivers are installed. Also, perhaps try using a different cable than the cord that comes with OnePlus Nord N200.
Without being connected to your computer, complete the button combination, and after a second or so, plug your device into the PC with MSM tools open (While still continuing the button combo). The screen will produce a momentary flash of black/green and it will ultimately connect to the MSM tool.
If that doesn't work, try this:
Open MSM tools and pick the appropriate parameters
Make sure your device is turned off
Connect the USB cord to your computer and then connect the other end to the OnePlus Nord N200 while holding the volume up and down buttons
It will then display the "connected" status in MSM tools for perhaps 2 or 3 seconds
Immediately click "start" in MSM tools (This will erase the whole device and relock the bootloader if it was previously unlocked)
Edit: Added proper warning
ive tried installing the drivers but i cant seem to get the qualcomm ones installed
red5815 said:
ive tried installing the drivers but i cant seem to get the qualcomm ones installed
Click to expand...
Click to collapse
nvm i had to get it from several different sites, its working now and unbricked!
red5815 said:
nvm i had to get it from several different sites, its working now and unbricked!
Click to expand...
Click to collapse
Red5815, great job! I'm glad you were able to get your device operating again.