Please Help Gear S in Endless Boot loop! - Samsung Gear S

Hello,
Please help me, I followed the guide on this page https://forum.xda-developers.com/gear-s/development/dev-gear-s-android-port-t3177740
and It worked getting android wear on my gear s watch. But then when I was using Odin to install Stock Firmware. It goes into an endless boot loop.
To make matters worse, I tried putting back android wear (Which worked the first time) and now it also goes in an endless boot loop.
So now I'm back on the Latest Stock firmware which still has a boot loop, and which I downloaded from sammobile.com.
Can someone explain why there is an endless boot loop and give a solution?
Thank You

Solved
Hello. I think i found the 'bug'
After a couple of hours of testing the Gear S i discovered that the looping issue is caused by the way the watch is handling notifications. Everythings fine when the Gear S is constantly connected with bluetooth and mobile network/wifi. The trouble starts when the connection changes from bluetooth to mobile network/wifi. When the gear is set to 'automatic on/off it will take a while to connect, about a minute with my gear. If a notification reach your cell phone during the time a new connection is set up on the Gear, there will be no connection. The flashing/looping of the screen starts when a bluetooth connection is re-established and the 'hanging' notification(s) are pushed to the Gear.
Solutions:
- disable notifications
- delete the notifications from your cell phone when connected with bluetooth, after that the looping stops immediatly
- connect to a network before you're out of bluetooth reach
Important note: this works on my Gear, no problems anymore since. Hope this works for you too, let me know!
sorry for my poor english...

Related

[Q] Cubot One Bluetooth Connection Issues

I have a Cubot One, using the G800_CUBOT_D1_V0.8_20140124_MJK firmware (4.2.1) - it was previously on the 0.6 firmware and had the same issue.
What I have experienced is that when connecting to a device with Bluetooth - in this case a Sony SW2, but have also tried Bluetooth headsets - it has problems pairing.
The phone sees the BT device as an available device, and when I select it, it starts the pairing process. Initially it seems to be ok and successfully pairs for 2-5 seconds, the the device is relisted as an available device, but not connected. I have had success twice. The first time was immediately after rooted my phone, and this was ok for several days, even rebooting my phone and the watch didn't seem to cause the issue again, but then it randomly stopped working. I was unable to connect until flashing with the 0.8 ROM. At this point is was again working for about 24 hours - even better than before - until I switched the watch off. Since then I have been unsuccessful in pairing again.
Interestingly, when I try to pair with my Galaxy Tab 2 I have the same problem, UNLESS I initiate the connection with the tablet, then it is fine.
I know that there were problems with the Bluetooth stack on 4.2.1 when it first came out, and it may be related to that, but can anyone offer suggestions as to what else I can try?

Screen turning on repeatedly

Hey everyone!
I picked up a Gear S about a week ago and until today, I've had no problems. I took the watch off charge this morning and everything was working as fine, used some apps etc, no issues. Then I checked my phone for updates and saw that the Gear Manager app had an update and I installed it. Since then, the screen on my Gear S has been constantly turning on and off. It will turn for about 9 seconds, then switch off and back on 2 seconds later. Turning the screen on manually works but everything is pretty much frozen. I can periodically get as far as the pedometer (because there's an icon for it on the home screen) or to the Apps menu but no further and then the screen will switch itself off.
I'm not sure whether an update to the Gear Manager app should affect the watch itself but I know that when I wiped my phone a few days ago and went to set up the Manager again, it factory reset the watch so I assume there is a direct connection between the software. I've tried disabling both Bluetooth and the remote connection to check if Gear Manager is causing the screen to behave strangely but it's still turning on and off. It's impossible to do a soft reset through the Gear S itself as the screen switches off before I can get to settings and I've tried doing a hard reset but nothing works.
I tried searching on Google for anyone having similar issues and the only thread I can find was posted on Android Central (yesterday I think) with a few people saying that they're having the same problem which makes me thing that the update to Gear Manager is the issue.
Edit: The only screen that doesn't seem to be affected is the PIN lock screen. Screen switches off there as normal and does not come back on.
Edit 2: I've never reset the Gear S before (and I only noticed the factory reset mentioned above after it was finished) but when I attempt to do a hard reset, the watch just reboots as normal without anything happening and all info / data is still there. I presume this really shouldn't be the case?
UPDATE: I'm an idiot / Samsung's instructions on how to do a hard reset are awful.
I decided to Google how to do a hard reset and discovered that when in the Recovery Menu, you need to hold down the Power button to choose an option (Samsung's instructions just tell you to press the Power button until you highlight what you want and I assumed it would automatically choose that after a few seconds because the phone would restart for me). Watch is now factory reset and so far the screen issue appears to be resolved. Another four hours of transferring music it is then.
@BOZG can you post a link to that thread?
I have the Same problem. Sometimes changing a clock face or installing/uninstalling a program seems to make it stop. I have yet to find a good consistent solution. Restarts etc. don't help. Hard reset will fix it but last time I just changed settings on and off and powered the phone on and off and eventually it stopped.
It seems related to when the phone is connected remotely over a cell network. I have the AT&T unlocked with a T-Mobile regular line, not the wearable line since I have a 5 for $100 business plan and the 5th line was not being used. Doubt that makes a difference though.
Followup:
Just now I had the watch off and charged to 100%. Powered up with phone off. Same issue. Watch face loads, the hands change to the current time, then it slides down the screen and looks like a reload because when it comes back up the time isn't correct. The hands reset to the right time. This happens a few times. I power the phone up. Bluetooth connects. I open the gear manager on the phone and it stops.
Will try to repost if that's repeatable. I hope they fix it because it burns quite a bit of battery when it happens. It gets warm so it's running the CPU a lot whatever it is.
allow to power down
BOZG said:
Hey everyone!
I picked up a Gear S about a week ago and until today, I've had no problems. I took the watch off charge this morning and everything was working as fine, used some apps etc, no issues. Then I checked my phone for updates and saw that the Gear Manager app had an update and I installed it. Since then, the screen on my Gear S has been constantly turning on and off. It will turn for about 9 seconds, then switch off and back on 2 seconds later. Turning the screen on manually works but everything is pretty much frozen. I can periodically get as far as the pedometer (because there's an icon for it on the home screen) or to the Apps menu but no further and then the screen will switch itself off.
I'm not sure whether an update to the Gear Manager app should affect the watch itself but I know that when I wiped my phone a few days ago and went to set up the Manager again, it factory reset the watch so I assume there is a direct connection between the software. I've tried disabling both Bluetooth and the remote connection to check if Gear Manager is causing the screen to behave strangely but it's still turning on and off. It's impossible to do a soft reset through the Gear S itself as the screen switches off before I can get to settings and I've tried doing a hard reset but nothing works.
I tried searching on Google for anyone having similar issues and the only thread I can find was posted on Android Central (yesterday I think) with a few people saying that they're having the same problem which makes me thing that the update to Gear Manager is the issue.
Edit: The only screen that doesn't seem to be affected is the PIN lock screen. Screen switches off there as normal and does not come back on.
Edit 2: I've never reset the Gear S before (and I only noticed the factory reset mentioned above after it was finished) but when I attempt to do a hard reset, the watch just reboots as normal without anything happening and all info / data is still there. I presume this really shouldn't be the case?
Click to expand...
Click to collapse
I left mine to use up all the battery,then when it switched off, i left for 2 days and when i switched back on... all fine again.
theroblog.com said:
@BOZG can you post a link to that thread?
I have the Same problem. Sometimes changing a clock face or installing/uninstalling a program seems to make it stop. I have yet to find a good consistent solution. Restarts etc. don't help. Hard reset will fix it but last time I just changed settings on and off and powered the phone on and off and eventually it stopped.
It seems related to when the phone is connected remotely over a cell network. I have the AT&T unlocked with a T-Mobile regular line, not the wearable line since I have a 5 for $100 business plan and the 5th line was not being used. Doubt that makes a difference though.
Followup:
Just now I had the watch off and charged to 100%. Powered up with phone off. Same issue. Watch face loads, the hands change to the current time, then it slides down the screen and looks like a reload because when it comes back up the time isn't correct. The hands reset to the right time. This happens a few times. I power the phone up. Bluetooth connects. I open the gear manager on the phone and it stops.
Will try to repost if that's repeatable. I hope they fix it because it burns quite a bit of battery when it happens. It gets warm so it's running the CPU a lot whatever it is.
Click to expand...
Click to collapse
samsung gear s screen on and off..looping
There you go. Not much to read there though as it's just me and OP. The problem re-emerged for me after a few days again so I was forced to do another hard reset to actually use the watch. I noticed it when I woke up in the morning and noticed that another update had been pushed to the Gear app. That's twice now that this has happened shortly or immediately after the Gear app was updated.
I haven't been able to uninstall an app / change clock face to see if it works as the watch is completely unusable when it happens to me. The Gear app registers that it's connected but it's impossible to change anything from there either and if I turn the watch off and back on again, the Gear app will no longer connect.
petethepete2000 said:
I left mine to use up all the battery,then when it switched off, i left for 2 days and when i switched back on... all fine again.
Click to expand...
Click to collapse
Not sure if I've actually tried letting the battery drain. I'll try that the next time it happens (if it happens).
I had the same problem after the update, a reboot didn't solve the problem. Eventually the battery drained. After a recharge most is fine but I never know which watch face will suddenly appear.
Same issue again. Didn't see the Gear app updating but there was an update released the day before. Going to switch off auto-updates and see if it definitely the problem. Just seems too coincidental that this problem starts right after an update is released for the Gear App.
petethepete2000 said:
I left mine to use up all the battery,then when it switched off, i left for 2 days and when i switched back on... all fine again.
Click to expand...
Click to collapse
Started doing it again yesterday so let the battery die and charged it fully and it didn't help. Left it on the box overnight and brought it to a Samsung Service Centre this morning and of course it was working again when I took it out of the box! Left it with them anyway so I'll see what happens.
I've had my Gear S a few weeks and it has also started doing this, I will give some of the suggestions here a go.....
EDIT: So opening the Gear Manager App once Bluetooth was connected brought my Gear S back to life. Phew!
It's only entered this state after I turned it off at night and then turned it back on in the morning - so it had been off roughly 8 hours. Upon turning it on the screen would cycle from the right time and notification numbers and the wrong time and wrong notification numbers too off again.
@ BOZG - Just wondering if you got your S back yet and if so, were they able to tell you what was causing this on/off problem. Mine just started doing it yesterday.
Also, how did you find the "Samsung Service Centre"?
holding the screen seems to cause it...
Had to send mine to Samsung for a new charging cradle and they updated the software to latest, when i got it back it seemed fine. Then i was messing about with it and was holding the screen to my chest for a while and that seemed to cause it to happen. It seems to be the screens gets too much activation and it flips out. I think this is what started the problem last time it happened.1
Switching to power saving mode seems to fix it for me... have to wait until it gets low on battery and when the low bat warning comes on, switch then... leave for a bit then switch back to normal.
I called Samsung Thursday and they sent me a UPS label and told me to send the watch, charging cradle and AC charging cord back in for service. She told me it takes about 7-14 days. We shall see.
Happy to have found this. </rant>I'm starting to get enough of this Samsung stuff. I had the note 2 and now I have the note 4 and gear S. That is mote then 1000 euro of equipment. And today when I tried the restore to fix this, both the phone and the watch rebooted. Crazy that they can not build good software and hardware for this price. </rant>
To me it seems that is freezes somehow when this happens. It kept jumping back to 22:10 time and changed to the watch-face and settings keep rolling back. It seems to happen to me, when the watch is off for some hours. The samsung way... no update to fix this.
solved for me
hi first of all sorry if i do any mistakes because English is not my language
i had similar problem and i found the solution at least in my case . THE PROBLEM IS NOT WITH THE GEAR S
all was ok using 4.4.2 kitkat on my note 3 before few months i upgrade with lollipop 5 official from sammobile via odin
from that moment the problems begin with the reconnection of the gear with the note
long time to connect and no auto reconnection only manual by turning off-on the bluetooth
i was boring to do format to the note3 so i left it as it
few weeks ago probably of gear manager update the gear start freezing and the screen turning on and off
first i do a factory reset and the gear was ok for a while but after it do the same but the next time the screen was not ok the colors was different so i send to service in Athens
the service in Athens is very fast and very helpful , is one of the reasons that i will difficult go with other manufacture , so they return me the gear saying that they change the motherboard and now there is new imei
but the gear that they send me was brand new except the band and the box. BUT after some time the same problem ..... i call them and they tell me to send it back so i send it and i receive it again but this time the say that the watch is ok
GUESS NOW .... i turn it on and after a while of the connection with my note AGAIN the same problem the screen on and off and freezing plus was overheat underneath
i was ready to call them and to say few words but they was closed ..... then i search the net and i found this post and i thing probably is not the gear the problem ,no hardware problem, i decide to do a test
i download the last working rom to my phone 4.4.2 and magically the problem disappears .... but now there is a software update on my phone lollipop 5 so i do the update and i was ready if the phone cause again the same problem
to return and stay with 4.4.2 But now all is ok the problem solved .... now is more of 24h and all are ok
i hope this will work for you also
Same problem
I have the same issue exactly - Note 4 with latest lollipop upgrade - it is very frustrating......I don't particularly want to have to move back an OS just to use the watch !
JALUK said:
I have the same issue exactly - Note 4 with latest lollipop upgrade - it is very frustrating......I don't particularly want to have to move back an OS just to use the watch !
Click to expand...
Click to collapse
Ok but doing a downgrade and all working ok you can do update again.... i am not with 4.4.2 i went to the latest 5.0 for me now and all are ok.
Maybe something was wrong with the update procedure.
UPDATE
the touch function of the 2nd gear stop working so i send it back and they send me new device
for a few days all was ok . But today when i restart the phone while the gear was disconnected the problem with screen turning on repeatedly appears again .
for sure is not problem of the gear , this is the 3rd device in my hands, something is wrong with the gear manager software .
i have also reconnection problems .... if the phone is far away and they lost Bluetooth connection the most of the times i must reconnect manually , the gear say disconnected but the note think is still connected
I wonder has anyone tried to reset the watch as a stand alone device and see if the problem happens? I know you might lose a lot of the blue tooth functionality but I think I will test it and see if the problem still happens.

Random Reboots and Frustrations T_T

So recently I have been having random reboots for my s6 edge (SM-G925W8) running G925W8VLU2AOG2 stock
I am not sure whats going on but when i'm at home the phone seems to be fine when connected to wifi, bluetooth etc.
As soon as I got to my university and im listening to music with Wifi turned on I believe the phone just randomly starts restarting and I cant stop seem to stop it until the phone runs out of battery, it'll keep on rebooting. I have a theory that maybe the wifi is somehow conflicting but again im not sure. The phone works fine at home....
There seems to be too many variables at play and I have no idea how to solve this
I desperately need my phone for school and personal stuff
Troubleshooting steps I have taken
- FULL factory reset with ODIN (wiped everything)
- Tried Safe mode didnt help.
I would just to bump and update you guys that I have confirmed its the wifi causing it. Everytime i connect to my school wifi , my phone just starts rebooting randomly and just keeps going. Now the question is how do i solve this =/

[Q] [REQ] Connection To Phone - Help?

After a fresh rom wipe it was connecting awhile in gear manager and then one day led to two days and then three days to four days and so on no successful connection in gear manager...
I don't wanna have to custom recovery wipe my phone every time I want it to connect, I really wished they would've locked a connection to the watch and phone...
Not sure if it's cause of my custom kernel, kernel settings app.
Is there a way to lock in a connection, I noticed sometimes on my watch while trying to connect to gear manager if I stop it the watch says bluetooth lost or something along those lines of not connected.
I'm running Hyperdrive Note Edge N915T KitKat 4.4.4 NK3 Low Lying Fruit Kernel and Gear S TizenMod Experimental Build OA7 R750T.
Any help on this would be greatly appreciated.
Even with older Gear Manager every time I click connect I get a message that says Bluetooth has been disconnected WTF samsung you're doing it backwards!!

Lg v60 Problem with wifi

When I click my wifi icon it lights up like it's trying to turn on, but turns off after a few seconds without connecting. I can temporarily fix the problem by restarting my phone. It will turn on and connect after restarting. But if I turn the wifi off and back on again, it has the same problem. I really don't want to have to restart my phone every time I want to use the wifi, so if anybody has any idea how to fix this, that would be awesome.
Never had that issue, I'm currently on latest fw v10m and no issues at all, connected to Wi-Fi ax router.
Is this a mesh type access point. Been having issues with google wifi. It stops connecting to the same ap after a while but it will connect to the other ap's . Once I reboot I'm back to normal. There is another thread with this info. Unfortunately no fix yet, looks like a bug. Hopefully it will be fixed in the next update.

Categories

Resources