Hello, I'd like to root my LG X Power (K220), but I can't find any guide for that. I tried KingRoot and Kingo root. And also, there is no TWRP build for my phone. So, is there any method to root my phone? Im running Android 6.0.1
persevere
karqinis said:
Hello, I'd like to root my LG X Power (K220), but I can't find any guide for that. I tried KingRoot and Kingo root. And also, there is no TWRP build for my phone. So, is there any method to root my phone? Im running Android 6.0.1
Click to expand...
Click to collapse
don't give up. someone will help you
there is always a way
keep researching
Please help me
I faced a problem with the phone LG X power
The phone work good when I concted the phone to the pc in the normal mode.
But don't work when I entered the phone on the download mode always give me in device manager the device cannot start code number 10 and I installed all drivers from LG site and LG Bridge
أرسلت من LG-K220 بإستخدام تاباتلك
hy. ok so i was able to boot into twrp on my k220 but cant install root because of data encryption. the device wont boot normally after root install in twrp
cant root systemless because of boot.img
some advice would be good
thanks
ok I also tried to edit host but can't do it the phone will not boot only after factory reset
aeadfase said:
Please help me
I faced a problem with the phone LG X power
The phone work good when I concted the phone to the pc in the normal mode.
But don't work when I entered the phone on the download mode always give me in device manager the device cannot start code number 10 and I installed all drivers from LG site and LG Bridge
أرسلت من LG-K220 بإستخدام تاباتلك
Click to expand...
Click to collapse
That's the right mode. Will work with LG flash toll just change port on device manager
Sent from my LG-K220 using Tapatalk
ok sow i root my phone finally!!!! but is not permanent
i need to use soft reboot if i use complete reboot it doesn't start anymore
slyver2008 said:
ok sow i root my phone finally!!!! but is not permanent
i need to use soft reboot if i use complete reboot it doesn't start anymore
Click to expand...
Click to collapse
More by soft reboot we can not install the exposed.
slyver2008 said:
ok sow i root my phone finally!!!! but is not permanent
i need to use soft reboot if i use complete reboot it doesn't start anymore
Click to expand...
Click to collapse
How did you do to have temporary root? Take a tutorial.
root k220 temporary
all your internal data will get lost
download rootk220 the put that files into micro sd
install lg drivers on your pc
enable usb debug in developer options
adb reboot bootloader
unlock bootloader [fastboot oem unlock]restart it will ask to factory reset . do it
repeat all the procedure to gain adb access
adb reboot bootloader
fastboot boot TWRP.img ------ dont flash
if is asking for password decrypt cancel
swipe to allow system write
restart phone with twrp then you will get a message that your device is corrupted but will restart
reboot again into bootloader the boot into TWRP
fastboot boot TWRP.img cancel for password decrypt and system write
install zips now in this order
1 .rce_univ.zip
2. super user
3. rce_univ.zip
4. VerifiedBootSigner-v8.zip
dont wipe anything just reboot and your done you will have root access
for reboot use soft reboot apps
if you will reboot the phone will never starts until you flash new firmware
cheers
Where do I find these four zip files?
Gilanio said:
Where do I find these four zip files?
Click to expand...
Click to collapse
Read my post there is a download link named rootk220
Sent from my LG-K220 using Tapatalk
slyver2008 said:
Read my post there is a download link named rootk220
Sent from my LG-K220 using Tapatalk
Click to expand...
Click to collapse
I found it, thank you. You have urged the exposed
The Exposed Framework
I did everything according to slyver2008's instruction, i try change imei from terminal and after rebooted the phone. Now it does not start and I can not update the firmware any more.
when loading, it writes your deevice is corrupted.
I tried to switch to the firmware update mode - volume up and connect usb. and flash with LGMobileSupportTool or LG Flash Tool 2014, but nothing helped.
that it is possible to make tell me please?
uzoom said:
I did everything according to slyver2008's instruction, i try change imei from terminal and after rebooted the phone. Now it does not start and I can not update the firmware any more.
when loading, it writes your deevice is corrupted.
I tried to switch to the firmware update mode - volume up and connect usb. and flash with LGMobileSupportTool or LG Flash Tool 2014, but nothing helped.
that it is possible to make tell me please?
Click to expand...
Click to collapse
Don't worry if the device isn't recognized in Windows . Use lguptool for 2016 kdz firmware and then go to device manager where the phone is in download mode change port to 41 then you will see that the restore will begin
Sent from my LG-K220 using Tapatalk
slyver2008 said:
all your internal data will get lost
download rootk220 the put that files into micro sd
install lg drivers on your pc
enable usb debug in developer options
adb reboot bootloader
unlock bootloader [fastboot oem unlock]restart it will ask to factory reset . do it
repeat all the procedure to gain adb access
adb reboot bootloader
fastboot boot TWRP.img ------ dont flash
if is asking for password decrypt cancel
swipe to allow system write
restart phone with twrp then you will get a message that your device is corrupted but will restart
reboot again into bootloader the boot into TWRP
fastboot boot TWRP.img cancel for password decrypt and system write
install zips now in this order
1 .rce_univ.zip
2. super user
3. rce_univ.zip
4. VerifiedBootSigner-v8.zip
dont wipe anything just reboot and your done you will have root access
for reboot use soft reboot apps
if you will reboot the phone will never starts until you flash new firmware
cheers
Click to expand...
Click to collapse
Hey but could we do perma root because thats my only device and i dont want to brake it wehn i reboot it normal or can we repair the device when we did a normal reboot sorry for asking that much but i am 13 and thats my only device and.
For now doesn't work in permanent mode.but you can restore it with lguptool for kdz firmware from 2016. You will lose all your internal data
Sent from my LG-K220 using Tapatalk
slyver2008 said:
For now doesn't work in permanent mode.but you can restore it with lguptool for kdz firmware from 2016. You will lose all your internal data
Sent from my LG-K220 using Tapatalk
Click to expand...
Click to collapse
Hey pls anwser fast because i am in twrp so now do i need to cancel password and System read
---------- Post added at 12:24 PM ---------- Previous post was at 12:03 PM ----------
slyver2008 said:
For now doesn't work in permanent mode.but you can restore it with lguptool for kdz firmware from 2016. You will lose all your internal data
Sent from my LG-K220 using Tapatalk
Click to expand...
Click to collapse
could i do a backup in twrp? and restore it than to repair my device
No backups can't be maid.as I said before you will lose all your data. If you fallow my guide you will gain root access but our lose all your data. If you complet reboot the device it doesn't start anymore and has to flashed with a new firmware
Sent from my LG-K220 using Tapatalk
It came out in the magisk version. Will be able to decrypt?
Related
Hii Guys..
I need the custom TWRP recovery for my LYF water F1S (LS -5201), so that i can root it and install custom ROMs. Developers i request you to do the needful please.
Regards
My phone also f1s.
Did you had any rom-package or recovery.img?
onkarrathee said:
Hii Guys..
I need the custom TWRP recovery for my LYF water F1S (LS -5201), so that i can root it and install custom ROMs. Developers i request you to do the needful please.
Regards
Click to expand...
Click to collapse
Try using this guide
https://forum.xda-developers.com/android/software/guide-how-to-compile-twrp-source-step-t3404024
Guys...i have found a page for the stock rom for LYF water F1s Ls-5201. You can download it from here
I also extracted the stock recovery image from device and here is the link https://drive.google.com/file/d/0BwMCGOjWJuaxY0NSemJ6ZzdNU1U/view?usp=sharing
Also tried the method to make TWRP for LYF water F1_ LS5201 by @suraj-b method.... but not successful yet. For the process i've used twrp recovery of Le 2 x526.
i'm not a developer but it would be my pleasure if whatever i tried, help somebody.
Don't forget to "Hit THANKS..."
onkarrathee said:
Guys...i have found a page for the stock rom for LYF water F1s Ls-5201. You can download them from there http://www.needrom.com/download/lyf-ls-5201/#
I also extracted the stock recovery image from device and here is the link https://drive.google.com/file/d/0BwMCGOjWJuaxY0NSemJ6ZzdNU1U/view?usp=sharing
Also tried the method to make TWRP for LYF water F1_ LS5201 by @suraj-b method.... but not successful yet. For the process i've used stock recovery of Le 2 x526.
i'm not a developer but i would be my pleasure if whatever i tried, help somebody.
Don't forget to "Hit THANKS..."
Click to expand...
Click to collapse
Good job !
How to flash stock firmware to LYF water F1s Ls-5201
Prepare your system-----
1) Install the Qualcomm usb drivers on your system. Download link
2) Check your PC device manager, your phone should be detected in "Qualcomm HS-USB QDloader 9008" mode. It must detect to start the process.
3) Download the stock firmware from here . The software version downloaded with this link is "LS-5201-S10A_LYF_L13EN_200_170124_09-55-13".
4) Extract the downloaded firmware zip to an folder and rename the "IMAGES_FOR_QMSCT" to "firmware".
5) Download & install the QPST tool. Google it you can find it easily.
6) power off your phone & Make sure your device is charged to at least 50%.
7) Run the installed QFIL from installed programmes. Browse in programmer path to the "prog_emmc_firehose_8976_ddr.mbn" file in the folder where firmware is extracted. It will load the firmware & buid will be selected automatically.
8) Click on load xml and select the "rawprogram_unsparse_without_qcn.xml" if you havn't the backup of NV partition of your device.
If you have the backup NV partition of your device than you can select "rawprogram_unsparse.xml" because this will erase your RF Calibration data, IMEI and WiFi/Bluetooth Address etc. and you will have to restore the NV partition after installing the ROM.
I would suggest you to select "rawprogram_unsparse_without_qcn.xml" & keep it simple.
9) Choose the "patch0.xml" after that.
10) Hold the vol+ & vol- key together and plug usb cable to phone to enter into download mode. As you plug in the QPST tool would recognise your device in QDLoader 9008 mode with com port no. and download button will get activated.
11) Click the download button and sit back, it will take some time.
12) "finish dowload" appear, when process got completed and phone will reboot automatically.
13) Disconnect the device from PC one "android screen" appears (usually it takes 5 min. to appear LYF logo screen from android boot screen)
14) If doesn't reboots, there is some problem & get ready for real hard work .
You might have bricked. In this case just press the power button so than it can power ON. If android screen appears you are lucky enough
-----If android screen remains more than 6-8 minute, you are in bootloop. (It useually takes 5 min for LYF logo to appear after android logo)
-----To switch off your device in case of bootloop, press vol+, vol- & power key together for some time. It will switch off.
-----try to flash the firmware again by above process.
I have tested this method on my device and successfully flashed the stock firmware.
Don't forget to "HIT thanks"...!!!
Credit:
@[email protected] for providing the stock firmware
Me: for testing the procedure
Le2 not support MicroSd.
I will try use recovery of oppo R9plus.
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/open?id=0BwVjewgp3fvLbmtxZ21fSUZhOW8
Or download full package with flash tools and supersu.zip [URL="https://drive.google.com/open?id=0BwVjewgp3fvLUnRHS3NGRjlIRTQ]TWRP-OneKeyFlash-supersu-lyf-water-f1s.rar[/URL]
TWRP recovery LYF_LS-5201
Guys... here is the unofficial twrp recovery for LS-5201. Download it here .
Let me know that you suceed..
This is twrp_unofficial_3.1.0.0 ported from Leeco Le2's TWRP recovery using @suraj-b method and if anythong goes wrong on your device download the stock recovery from the thread and flash it from bootloader.
Try on your own risk..!! :fingers-crossed:
Don't forget to HIT "Thnanks" down there
Please share the adb & fastboot files you used for unloacking bootloader and flashing recovery for the noobs. It would help.
keep it up. :good:
zjsss said:
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/file/d/0BwVjewgp3fvLRm9IM0FOcTF1aGc/view?usp=sharing
Click to expand...
Click to collapse
zjsss said:
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/file/d/0BwVjewgp3fvLRm9IM0FOcTF1aGc/view?usp=sharing
Click to expand...
Click to collapse
How to flash it bro...plzzz give us step by step help
---------- Post added at 06:22 PM ---------- Previous post was at 06:14 PM ----------
zjsss said:
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/file/d/0BwVjewgp3fvLRm9IM0FOcTF1aGc/view?usp=sharing
Click to expand...
Click to collapse
If i flash it via fastboot...den can i root it through twrp...
prashant.palange said:
How to flash it bro...plzzz give us step by step help
---------- Post added at 06:22 PM ---------- Previous post was at 06:14 PM ----------
If i flash it via fastboot...den can i root it through twrp...
Click to expand...
Click to collapse
You can download full package and use "OneKeyFlash(LYF-f1s).bat" to flash easier TWRP-OneKeyFlash-supersu-lyf-water-f1s.rar
zjsss said:
You can download full package and use "OneKeyFlash(LYF-f1s).bat" to flash easier TWRP-OneKeyFlash-supersu-lyf-water-f1s.rar
Click to expand...
Click to collapse
Bro but is it proper twrp for f1s...hv u try it
prashant.palange said:
Bro but is it proper twrp for f1s...hv u try it
Click to expand...
Click to collapse
It works well on my phone.
zjsss said:
It works well on my phone.
Click to expand...
Click to collapse
Thnk u soo much to bring us such wonderfull recovery....but bro...i found 2 issue....1 internal storage is showing empty 0mb and 2 der is no option for root like supersu.zip..plzz help me for dat...m i done wrong anything..plzzz help thank u sooo much brother...it doesn't mount internal storage..i tried mound system and data....but data doesn't mount...plzz help..hope u will understand
prashant.palange said:
Thnk u soo much to bring us such wonderfull recovery....but bro...i found 2 issue....1 internal storage is showing empty 0mb and 2 der is no option for root like supersu.zip..plzz help me for dat...m i done wrong anything..plzzz help thank u sooo much brother...it doesn't mount internal storage..i tried mound system and data....but data doesn't mount...plzz help..hope u will understand
Click to expand...
Click to collapse
It's my bad. This img had bugs.I well try to fix it.
You can copy supersu.zip to MircoSD and install it in TWRP rigtht now.
I checked by adb shell root is success.
Very sorry about that.
zjsss said:
It's my bad. This img had bugs.I well try to fix it.
You can copy supersu.zip to MircoSD and install it in TWRP rigtht now.
I checked by adb shell root is success.
Very sorry about that.
Click to expand...
Click to collapse
U r simply genius brother..root works properly.....god bless u ..love u ....:laugh::good:
Just try to make bugless twrp....thnk u in advance....
prashant.palange said:
U r simply genius brother..root works properly.....god bless u ..love u ....:laugh::good:
Just try to make bugless twrp....thnk u in advance....
Click to expand...
Click to collapse
Thx,i found this not a bug.
/data was locked by system.
Into twrp and keep /system read only,
And wipe /data will be ok .
but it will lost all your data in the phone!!!
So backup everything before you do it.
and install supersu .zip again to root.
zjsss said:
Thx,i found this not a bug.
/data was locked by system.
Into twrp and keep /system read only,
And wipe /data will be ok .
but it will lost all your data in the phone!!!
So backup everything before you do it.
and install supersu .zip again to root.
Click to expand...
Click to collapse
So what should i wipe...dalvik, cache, and data dats it..okay....not system...m i right? But data is not mounting den how can i wipe it?
prashant.palange said:
So what should i wipe...dalvik, cache, and data dats it..okay....not system...m i right? But data is not mounting den how can i wipe it?
Click to expand...
Click to collapse
It doesn't matter of wipe /date or wipe 3.
I guess because the phone kernel was rooted.TWRP had right of wipe.
But not so sure that.
I wanted to make sure everyone read this part first so that you know it's critical to backup because it happened to me figuring things out. If for any reason you are stuck in a boot loop, just reload twrp recovery and restore boot.img that you backed up for an easy quick fix.
Install drivers and adb on your PC.
Open command prompt or search 'cmd'.
Navigate to the directory with adb.exe
Download and store TWRP 2.2.2 (preferred) in the same directory where adb is located. Recommend renaming recovery file to recovery.img
Enable usb debugging on device by going to settings > about > and click on MIUI version repeatedly until developer settings are enabled. Go back and select additional settings to enable usb debugging.
Run the command: adb devices - to verify if able to connect to device (the serial number of your device will populate if so.
Run the command: adb reboot bootloader and phone device should say "Fastboot" in blue font
Run the command: fastboot boot recovery.img
Recovery will show in Chinese, click on the bottom right button to select English
May require to enter your default password you use to unlock your phone normally.
Click backup and be sure to backup system, boot, and recovery most of all so it's easy to recover your device moving forward.
Download and save SuperSU (I have been unsuccessful in getting Magisk to work at this time) onto storage device from PC to MI 8 that should appear with your Internal storage
Click on "Mount" in TWRP and unselect read-only
Click "Install" and flash SuperSU then reboot (my device rebooted one time and fully boot up the 2nd time so you're not alarmed)
Links:
SuperSU: https://download.chainfire.eu/1122/SuperSU/SR3-SuperSU-v2.82-SR3-20170813133244.zip?retrieve_file=1
TWRP: https://forum.xda-developers.com/mi-8/development/recovery-twrp-3-2-2-0703-t38126005
Appreciate any feedback, ideas, thoughts, or suggestions where all can collaborate and expand where we help each other further. Look forward to the future development of the MI 8 folks! Please note, I wanted to share the method that seemed to work best for me, but please be aware each and every single MI 8 device is not always exactly the same and the end result may vary and I'm not held accountable or responsible should you choose to follow the directions listed above. However, I wanted to share this information to help avoid any frustration going forward and save you time.
p.s. - If someone could help me figure out how to get twrp recovery to hold and not end up being replaced by mi recovery I would be most grateful as this has been an issue for me (I tried flashing, booting, and installing the img through twrp with no success). Thank you.
Hello thanks for your guide but i think we first need to unlock bl And for the twrp recovery to stick and not to be replaced by xiaomi recovery we need to flash something called "dm-verity " it basically removes that check, which replaces any other recovery by xiaomi recovery
Have a nice day and thanks for your work
I thought so as well, unfortunately I just haven't had much luck with dm verity which led to a soft brick on my device. I'll have to look over the code as it may vary in comparison to other xiaomi devices.
Sent from my MI 8 using Tapatalk
Fastboot flash recovery Command should do it ..
mekaziah said:
I wanted to make sure everyone read this part first so that you know it's critical to backup because it happened to me figuring things out. If for any reason you are stuck in a boot loop, just reload twrp recovery and restore boot.img that you backed up for an easy quick fix.
Install drivers and adb on your PC.
Open command prompt or search 'cmd'.
Navigate to the directory with adb.exe
Download and store TWRP 2.2.2 (preferred) in the same directory where adb is located. Recommend renaming recovery file to recovery.img
Enable usb debugging on device by going to settings > about > and click on MIUI version repeatedly until developer settings are enabled. Go back and select additional settings to enable usb debugging.
Run the command: adb devices - to verify if able to connect to device (the serial number of your device will populate if so.
Run the command: adb reboot bootloader and phone device should say "Fastboot" in blue font
Run the command: fastboot boot recovery.img
Recovery will show in Chinese, click on the bottom right button to select English
May require to enter your default password you use to unlock your phone normally.
Click backup and be sure to backup system, boot, and recovery most of all so it's easy to recover your device moving forward.
Download and save SuperSU (I have been unsuccessful in getting Magisk to work at this time) onto storage device from PC to MI 8 that should appear with your Internal storage
Click on "Mount" in TWRP and unselect read-only
Click "Install" and flash SuperSU then reboot (my device rebooted one time and fully boot up the 2nd time so you're not alarmed)
Links:
SuperSU: https://download.chainfire.eu/1122/SuperSU/SR3-SuperSU-v2.82-SR3-20170813133244.zip?retrieve_file=1
TWRP: https://forum.xda-developers.com/mi-8/development/recovery-twrp-3-2-2-0703-t38126005
Appreciate any feedback, ideas, thoughts, or suggestions where all can collaborate and expand where we help each other further. Look forward to the future development of the MI 8 folks! Please note, I wanted to share the method that seemed to work best for me, but please be aware each and every single MI 8 device is not always exactly the same and the end result may vary and I'm not held accountable or responsible should you choose to follow the directions listed above. However, I wanted to share this information to help avoid any frustration going forward and save you time.
p.s. - If someone could help me figure out how to get twrp recovery to hold and not end up being replaced by mi recovery I would be most grateful as this has been an issue for me (I tried flashing, booting, and installing the img through twrp with no success). Thank you.
Click to expand...
Click to collapse
Skickat från min MI 8 via Tapatalk
what issues do you get with magisk? I was able to flash it without any issues.
superior8888 said:
Fastboot flash recovery Command should do it ..
Skickat från min MI 8 via Tapatalk
Click to expand...
Click to collapse
Yes it does. Don't know why anyone would run SuperSU though.
mekaziah said:
I thought so as well, unfortunately I just haven't had much luck with dm verity which led to a soft brick on my device. I'll have to look over the code as it may vary in comparison to other xiaomi devices.
Click to expand...
Click to collapse
MAKE SURE U HAVE UNLOCKED BOOTLOADER
here is wat i do
first i boot into twrp
(make sure u have rom.zip magisk/superuser.zip an twrp.img) on internal storage
then i wipe
dalvik cache
cache
data (NOT FORMAT)
system
then i flash
rom.zip
twrp.img
then i reboot recovery
fkash magisk.zip
then reboot system
now i have new rom an still have twrp on
-fluffy- said:
here is wat i do
first i boot into twrp
(make sure u have rom.zip magisk/superuser.zip an twrp.img) on internal storage
then i wipe
dalvik cache
cache
data (NOT FORMAT)
system
then i flash
rom.zip
twrp.img
then i reboot recovery
fkash magisk.zip
then reboot system
now i have new rom an still have twrp on
Click to expand...
Click to collapse
Would you mind stating the version of Magisk?
Strange Guide no Attention for Unlok Bl.
barrielui said:
Would you mind stating the version of Magisk?
Click to expand...
Click to collapse
16.4
magisk has been working fine for me for a while
samwise110712 said:
what issues do you get with magisk? I was able to flash it without any issues.
Click to expand...
Click to collapse
What's your ROM version? I flash twrp then magisk, bootloop...
-fluffy- said:
MAKE SURE U HAVE UNLOCKED BOOTLOADER
here is wat i do
first i boot into twrp
(make sure u have rom.zip magisk/superuser.zip an twrp.img) on internal storage
then i wipe
dalvik cache
cache
data (NOT FORMAT)
system
then i flash
rom.zip
twrp.img
then i reboot recovery
fkash magisk.zip
then reboot system
now i have new rom an still have twrp on
Click to expand...
Click to collapse
Hello how did you flash the TWRP through the TWRP ???
What version of MiUi you have ???
omek07 said:
Hello how did you flash the TWRP through the TWRP ???
What version of MiUi you have ???
Click to expand...
Click to collapse
simple put twrp.img on ur storage
then flash img from twrp
-fluffy- said:
simple put twrp.img on ur storage
then flash img from twrp
Click to expand...
Click to collapse
Yes but its asking after in which partition.
What partition you chose ?
---------- Post added at 08:26 AM ---------- Previous post was at 07:41 AM ----------
-fluffy- said:
simple put twrp.img on ur storage
then flash img from twrp
Click to expand...
Click to collapse
Could you please tell me what rom you have ???
Thank you
omek07 said:
Yes but its asking after in which partition.
What partition you chose ?
---------- Post added at 08:26 AM ---------- Previous post was at 07:41 AM ----------
Could you please tell me what rom you have ???
Thank you
Click to expand...
Click to collapse
u choose recovery
im using miui eu
magisk is running without any issue.
i am on the newest xiaomi eu beta rom and flashed magisk 16.7 without any issue right now
(after waiting horrible 15 days for unlocking the bootloader)
Ok so both of you have the xiaomi eu. I have global stable 9.5.11. so maybe that's the problem
---------- Post added at 06:30 AM ---------- Previous post was at 06:29 AM ----------
So both of you have xiaomi eu rom. I have global stable 9.5.11. maybe that's the problem.
omek07 said:
Ok so both of you have the xiaomi eu. I have global stable 9.5.11. so maybe that's the problem
---------- Post added at 06:30 AM ---------- Previous post was at 06:29 AM ----------
So both of you have xiaomi eu rom. I have global stable 9.5.11. maybe that's the problem.
Click to expand...
Click to collapse
I have the lastest global version, I cannot get the root access...
Someone tell me flash the Chinese verision then flash xiaomi.eu and magisk.
felixrao said:
I have the lastest global version, I cannot get the root access...
Someone tell me flash the Chinese verision then flash xiaomi.eu and magisk.
Click to expand...
Click to collapse
My friend i changed to the Xiaomi eu and everything worked. You dont have to flash the Chinese Version first you can go from Global to Xiaomi.eu. Just dont forget to do FORMAT data and not only Wipe Data.
as stated above, i can't seems to find a workable root method for this device. i've already tried kingroot, kingoroot, and some unknown website that claimed have solution to root this device and make my phone restart and restart and restart.. luckily, my phone still can be saved.
im now at dead end. can someone help me how to root this device, and a clear tutorial since, im not good with android system..
thanks..
bump
while waiting for someone to come out with help. I've found a website which have "unofficial" twrp.
https://unofficialtwrp.com/doogee-bl12000-pro/
I want a comfirmation if this site is trustworthy.
I've tried flash the twrp into my phone but it keep booting at recovery and can't boot into system.
I'm flashing using CMD like this:
fastboot oem unlock
fastboot flash recovery recovery.img
fastboot boot recovery.img
Click to expand...
Click to collapse
and what the function of "fastboot flashing unlock"?
I'm thinking of using magisk to root my phone but I don't know what "stock boot image dump".
bump
seems that https://unofficialtwrp.com/doogee-bl12000-pro/ really work, but for my case, it's required me to decrypt password, while im not had any password.
after many times of rooting effort, it success. for those who have problem that occur to me:- BOOTLOOP at RECOVERY and RECOVERY can't read SDCARD or STORAGE
1. Root your phone using the twrp above
2. if bootloop to recovery, make sure you have sdcard and have supersu flash file inside it.
3. in twrp, go to wipe. and then format factory
4. go to mount and choose media sdcard
5. at the homescreen, go to install and then flash the supersu flash file.
6. done
Click to expand...
Click to collapse
in my case my phone gained root permission, but lose twrp recovery. i don't really know about phone, so i hope someone can add something to make this clear to who's that read.
my goal is to root, so without having twrp doesn't concern me much.
well.. my mistake.. the TWRP is there. i dindt realize it.
hello
Please help me
I mistakenly gave the recovery TRWP model 12000 to the phone
And now the phone is turned on and off
What should I do to be right?
please somebody help me
Doing this quick update because today, when trying to root my phone, bricked it several times and lost all app info
If you are using android 7.11, this guide works fine: https://forum.xda-developers.com/zenfone-3-zoom/how-to/how-to-root-zenfone-3-zoom-ze553kl-t3622256
If on android 8, SuperSU will brick your phone. Use Magisk instead:
- enable usb debug mode on your phone
- unlock bootloader
- plug phone into your computer
on your pc
- Download fastboot and adb:
* Windows: https://dl.google.com/android/repository/platform-tools-latest-windows.zip
* macos: https://dl.google.com/android/repository/platform-tools-latest-darwin.zip
* linux: https://dl.google.com/android/repository/platform-tools-latest-linux.zip
- download the latest Magisk unlock script from https://github.com/topjohnwu/Magisk/releases and copy it to a MicroSD or USB that you can attach to your phone. Look for Magisk, not Magisk Manager
- download twrp v 3.1.0-0-Z01H-20170408: https://mega.nz/#F!p90wgAaY!l1JbJilmAUEKTKWu43pT9w?E81jQTCD (this is from https://mega.nz/#F!p90wgAaY!l1JbJilmAUEKTKWu43pT9w, as described in the old root guide using twrp + supersu. It is supposed to be safe)
- `adb reboot bootloader`
- `fastboot flash recovery <path to twrp image downloaded>`
- `fastboot reboot`
Right now, you should probably backup your phone.
back on your phone:
- before booting, press volume up on the bootloader, there, select Recovery. Using fastboot to reboot into recovery might cause the stock recovery image to reflash
- if prompted to enable system modifications, allow it.
- If prompted to decrypt your data in TWRP, use the PIN you setup. If it doesn't work, I can't guarantee you won't brick our phone. Feeling brave enough? In case of brick keep reading, it is easy to restore your phone to stock Android 8 using official firmware.
- press install, choose the device attached to your phone that has Magisk-xxx.zip and select it
- flash the image and it should be OK
In case of brick or unsuccessful flash from SuperSU and without backup:
- Don't panic, like I did today
- download the latest firmware from Asus: https://www.asus.com/us/Phone/ZenFone-3-Zoom-ZE553KL/HelpDesk_BIOS/
- follow this guide: https://forum.xda-developers.com/zenfone-3-zoom/how-to/manually-update-to-7-11-t3815703
- when the phone reboots, boot into recovery
- enable ADB sideload
- on your pc: `adb sideload <path to newest firmare>`
- now follow the root guide above before starting your phone
- ???
- profit
Note: commands using adb and fastboot assume you have put the contents from the downloaded platform tools in your PATH, else execute them from the directory in which they were extracted, for instance, on linux:
- `cd /home/$USER/Downloads`
- `unzip platform-tools-latest-linux.zip`
- `cd platform-tools`
- `./adb devices`
Bricked my phone.
in which step?
You should have access to fastboot, try the downgrade tutorial and install android 7 then imediately flash the latest image from ASUS
gchamon said:
in which step?
You should have access to fastboot, try the downgrade tutorial and install android 7 then imediately flash the latest image from ASUS
Click to expand...
Click to collapse
After the magisk install. It logged some "can't mount partition" errors, I tried to wipe, but do not worked.
It got stucked on Asus logo.
I did the unbrick tutorial.
This is strange. Magisk is supposed to patch the boot image and install its app (by the way, if you update magisk using the app, phone enters bootloop)
Anyway, I have encountered myself many problems when installing, but nothing like this. Bootloops and corruption message on bootloader yes, but I can't seem to recall anything about partitions not being mounted. If installing stock recovery image, boot image and system doesn't do the trick, in my experience it is either bad partitioning, although unlikely, because those procedures doesn't repartition anything, or bad internal storage.
But just to be sure, you should reflash stock 7.1 image (recovery, boot and system) with fastboot, enter stock recovery and wipe cache/factory reset. If your phone is physically healthy, this should work
anonymousbsb said:
After the magisk install. It logged some "can't mount partition" errors, I tried to wipe, but do not worked.
It got stucked on Asus logo.
I did the unbrick tutorial.
Click to expand...
Click to collapse
Try to use twrp-3.2.3-0-Z01H-20181014, i faced the same issue and fixed by flash it
Enrico06 said:
Try to use twrp-3.2.3-0-Z01H-20181014, i faced the same issue and fixed by flash it
Click to expand...
Click to collapse
Cool, if this fixes the issue I will update the guide with this info
bro pls give an unofficial process to unlock this device because official unlock tool not working it shows "unknown network error".
kingairtel08 said:
bro pls give an unofficial process to unlock this device because official unlock tool not working it shows "unknown network error".
Click to expand...
Click to collapse
Downgrade to 7.1.1 and try it again.
Already tried on 7.1.1 lot of times same error shows.
please share a working process of unlock bootloader without asus unlock tool apk....i m waiting for 3 years
kingairtel08 said:
please share a working process of unlock bootloader without asus unlock tool apk....i m waiting for 3 years
Click to expand...
Click to collapse
normal. please wait 15min max
kingairtel08 said:
please share a working process of unlock bootloader without asus unlock tool apk....i m waiting for 3 years
Click to expand...
Click to collapse
I can't really help you there. This guide is supposed to work for those who are able to unlock bootloader using official asus tools. Never heard of unofficial unlock methods. It is possible that you have a hardware problem if you use those tools and they just don't work.
kingairtel08 said:
please share a working process of unlock bootloader without asus unlock tool apk....i m waiting for 3 years
Click to expand...
Click to collapse
Have you used the latest official unlocking tool? I see there's a July 2019 version available.
If you are on an older version of Android (not Oreo) are you presently still getting OTA update prompts?
I tried this tool but no result.
is it possible to root ZE553KL without loosing user application's data? I have unrooted device, wanted to migrate telegram secret chats to new phone. it is doable but with rooted smartphone only. if rooting process is destructive I cannot migrate. if rooting is doable with preserving installed applications along with their data then there is a hope for successful migration.
does this method look promising or it is just fake method?
Asus Zenfone 3 Zoom ZE553KL root using Magisk [No need TWRP Recovery
How to root Asus Zenfone 3 Zoom ZE553KL with Magisk [no need TWRP recovery, easy method to rood your Android device.
www.mobilewithdrivers.com
Unlocking Bootloader1. Make sure you have a sim and active mobile data. Then go to about phone tap build number 7-8 times. After that go to advanced settings > developer options > turn on OEM unlocking and then check if this device is secure and click add account and device.
2. Download Mi unlock tool from here. Extract it and paste it in C:/unlock. or else your device won't be recognized for unlocking.
3. Open Mi unlock tool and then enter the Mi account which was on your device. Put your device in fastboot mode by pressing vol- and power and then connect to PC. Press unlock and if it tells you to wait you have no other option but to wait. If your mi flash tool shows connect your device even after you have connected it. Follow this guide here.
4. After you have unlocked your bootloader reboot your phone.
Flashing TWRP and Rooting via magisk
1. Download this TWRP image here. Thanks to the original developer mauronofrio.
2. Download adb and fastboot tools here and install it.
3. Now put your phone in fastboot mode and connect it with your pc. Now where you have downloaded the TWRP file rename it to TWRP.img and open a CMD window there if you don't know how just google.
4. Type the following commands
1. fastboot devices
2. fastboot flash recovery TWRP.img
3. fastboot reboot recovery.
Click to expand...
Click to collapse
5. Your phone will boot into TWRP now. But TWRP will be overwritten by stock miui recovery to stop that you need to flash Magisk. Download this zip move it to internal storage then flash by tapping on install and swipe to flash. Reboot your device. Reboot to recovery again to check if TWRP is present.
Now your device is rooted
OR
Flash latest OrangeFox Recovery if you don't want magisk.
Flashing A rom
1. Download.
2. Flash.
3 Format Data.
Done
Feel free to ask any questions. And don't point a finger at me for messing your device.
My mi unlock tool says can't get info. I using Indian version miui 12
Thanks for the useful guide. I have a quick question, does this works with MIUI 12?
igeekyayush said:
My mi unlock tool says can't get info. I using Indian version miui 12
Click to expand...
Click to collapse
Sorry for late reply. Have you installed the drivers correctly? Try using another port in your pc or use this mi unlock tool version zip
Doombuggie85 said:
Thanks for the useful guide. I have a quick question, does this works with MIUI 12?
Click to expand...
Click to collapse
Yes, it does.
hello,
thanks for the reply sir. yes i've tired changing port, pc everything. today i've factory reset my phone and added mi account and now i'm getting 7 days wait time. let's see now
LoadOP2 said:
Sorry for late reply. Have you installed the drivers correctly? Try using another port in your pc or use this mi unlock tool version zip
Click to expand...
Click to collapse
igeekyayush said:
hello,
thanks for the reply sir. yes i've tired changing port, pc everything. today i've factory reset my phone and added mi account and now i'm getting 7 days wait time. let's see now
Click to expand...
Click to collapse
Okay keep the sim inserted and use the device for 7 days. And if it doesn't work try using older version of unlock tool.
Hi there!
Silly question: is it possible to install TWRP but keep the official ROM? (phone is unlocked)
_benedict_ said:
Hi there!
Silly question: is it possible to install TWRP but keep the official ROM? (phone is unlocked)
Click to expand...
Click to collapse
Flashing a custom rom is optional. You don't NEED to flash a rom to get TWRP...
---------- Post added at 06:48 PM ---------- Previous post was at 06:46 PM ----------
I've unlocked the bootloader using the unlock tool and waited for 7 days,
But i rooted the device using a different method where i patched a boot.img and flashed that to the device.
Will this method still work for me as I'm already rooted but just want TWRP so i can flash other ROMs.. The post says you have to flash magisk from the (temporary) TWRP for the TWRP to stay as the recovery..
Will the magisk on my phone and the magisk installed here collide?
I just want TWRP so i can switch to a custom rom, so any input is appreciated!!
_benedict_ said:
Hi there!
Silly question: is it possible to install TWRP but keep the official ROM? (phone is unlocked)
Click to expand...
Click to collapse
Skip the flashing a rom part and you will be good to go.
But i rooted the device using a different method where i patched a boot.img and flashed that to the device.
Will this method still work for me as I'm already rooted but just want TWRP so i can flash other ROMs.. The post says you have to flash magisk from the (temporary) TWRP for the TWRP to stay as the recovery..
Will the magisk on my phone and the magisk installed here collide?
I just want TWRP so i can switch to a custom rom, so any input is appreciated!!
Click to expand...
Click to collapse
You can flash twrp and then check if it persists. If not flash magisk again their is no thing as magisk colliding lol. Just make sure you flash a newer version. And if nothing works flash stock rom and then twrp.
If you have the stock boot IMG flash it and then intsall twrp and magisk.
smsry said:
Flashing a custom rom is optional. You don't NEED to flash a rom to get TWRP...
Click to expand...
Click to collapse
LoadOP2 said:
Skip the flashing a rom part and you will be good to go.
Click to expand...
Click to collapse
Haha, makes sense! Thank you for your answers
Nevermind.. i got it to work pretty easily..
I have twrp on this device and Pixel Experience ROM and it's working all fine..
But there's this one thing where when booting to recovery, it asks me to input a password for User(0) when i try to input anything it says password failed..
From reading the log, it says it's for decrypting data(8f I'm not mistaken)
Is this important? Do i need to decrypt it?
Currently the ROM works fine with no errors, so I'm not gonna bother, but would still like to know what this "decrypting" thing is..
smsry said:
Nevermind.. i got it to work pretty easily..
I have twrp on this device and Pixel Experience ROM and it's working all fine..
But there's this one thing where when booting to recovery, it asks me to input a password for User(0) when i try to input anything it says password failed..
From reading the log, it says it's for decrypting data(8f I'm not mistaken)
Is this important? Do i need to decrypt it?
Currently the ROM works fine with no errors, so I'm not gonna bother, but would still like to know what this "decrypting" thing is..
Click to expand...
Click to collapse
Yes, If you use a lock screen enter that password it will be decrypted. You will have to format data if you decide to flash any other rom anyway.
flashed twrp but not able to boot into recovery.
igeekyayush said:
flashed twrp but not able to boot into recovery.
Click to expand...
Click to collapse
There can be many reasons for that. Please tell me the error or what's actually happening. Then only I can be of help.
Sir ive used xiaomi flashtool v2 after that and it worked. Thanks sir. After that i updated to latest twrp from that chinese one.
LoadOP2 said:
There can be many reasons for that. Please tell me the error or what's actually happening. Then only I can be of help.
Click to expand...
Click to collapse
Joyeuse
Hello, Does it work for Joyeuse (European version)?
The name of TWRP says Curtana -Unified
rfguy said:
Hello, Does it work for Joyeuse (European version)?
The name of TWRP says Curtana -Unified
Click to expand...
Click to collapse
Yes Unified means all Snapdragon 720g Devices which include Joyeuse, Curtana, Gram, Excalibur.
Hey buddy, thank you for this quick step-by-step guide. I flash ROMs since 2012 and you know what? It helped me the same. Having all stuff needed for go from stock to custom concentrated in one place (plus some useful tip like the Magisk flash at the end) it's always useful and time-saving. Thank you
2 Micro-notes about fastboot btw:
- write 'fastboot (with lowered 'f'): it may confuse some newbie
- it's 'reboot' instead of 'boot'