Hi, I have a problem. 2 months ago I unofficially unlocked bootloader flashed twrp and everything necessary, then i tried many custom roms and there was no problems at all until yesterday when i tried to flash new rom.
I did everything correctly (like always - clean flash - rom- gapps) after that I got bootanimation loop ( sometimes happen - nothing very serious) so i wanted to reset once again to recovery twrp volume up + power to try once again and suddenly out of nowhere there was no twrp recovery. I had Mi logo ofc and after that for 0.5 sec there was a picture of droid laying with open chest and red triangle above and phone switched off. this screen lasts only for 0.5 - 1 sec and then disappear. When i try to boot system ( only power button) i get the same result mi logo -> "dead droid" screen for 1 sec and switch off.
From the other hand i can boot to fastboot but since i don't have any system on my phone (because it did not set up) and i can't go further than that screen i can't enable usb debugging to do everything by fastboot.
I tried also some edl.zip which helps with going into edl mode and I also can go to edl mode but miflash (newest) does not see my phone and I don't know why cause when plugged to computer phone is seen by it and in edl mode device is seen as Qualcomm HS-USB QDLoader 9008 port as it should be, but miflash does not see my device. I don't know if it's bricked as hell or what should i do.. ?
Thanks for answers in advance.
Samel_piesel said:
Hi, I have a problem. 2 months ago I unofficially unlocked bootloader flashed twrp and everything necessary, then i tried many custom roms and there was no problems at all until yesterday when i tried to flash new rom.
I did everything correctly (like always - clean flash - rom- gapps) after that I got bootanimation loop ( sometimes happen - nothing very serious) so i wanted to reset once again to recovery twrp volume up + power to try once again and suddenly out of nowhere there was no twrp recovery. I had Mi logo ofc and after that for 0.5 sec there was a picture of droid laying with open chest and red triangle above and phone switched off. this screen lasts only for 0.5 - 1 sec and then disappear. When i try to boot system ( only power button) i get the same result mi logo -> "dead droid" screen for 1 sec and switch off.
From the other hand i can boot to fastboot but since i don't have any system on my phone (because it did not set up) and i can't go further than that screen i can't enable usb debugging to do everything by fastboot.
I tried also some edl.zip which helps with going into edl mode and I also can go to edl mode but miflash (newest) does not see my phone and I don't know why cause when plugged to computer phone is seen by it and in edl mode device is seen as Qualcomm HS-USB QDLoader 9008 port as it should be, but miflash does not see my device. I don't know if it's bricked as hell or what should i do.. ?
Thanks for answers in advance.
Click to expand...
Click to collapse
Use the MiFlash Beta. It should work as you said your phone is recognized as QDLoader 9008. That's always a good sign. Do report back and tell us if that solved your problem.
Thanks I managed to fix it Problem solved!
Related
Hello, after playing with my z90 (with the original rom that was Z90a40_USR_S118 international, bought in october 2015) I wanted to clean it up and make some updates. So I made my backups etc... Entered the recovery (not the green lenovo one wich is very limited) with hold vol - , I choosed to wipe (the phone was encrypted just to mention) all that I can and reset to factory, all was done but when it finished, it reboot and it stuck to initializing just after lenovo logo it reboot... initializing... and it s an inifinite loop. So I retryed to go to the maintenance recovery but it s not possible a black screen come and it reboot, I can go to the limited lenovo green recovery, but no factory reset, so I make the wipe datas etc... nothing... infinite reboot loop!
So I found some rom put them in the micro SD, go for an update.zip with the recovery, update work well but... initializing.... reboot...
Grrr, lenovo... So I take the big tools, installed a minimal win7 with qualcom drivers, lenovo ones, qpst. I tried many manipulation to enter the download mode with port com (I finaly managed multiple times with not the exact manipulation it s vol- + power + 10s and multiple spanning of the vol - button....) And I have succefully flashed multiple roms with qfil but with always the same results... initializing, reboot... I don t know where to search now, I someone can help me to find where to go, perhaps reflashing the recovery or I saw the .qnc in a russian forum but I can t understand one word.... 2 days of flashing make me hate my lenovo, my first brick with a phone . Any help?
Thanks,
sorry for my bad english
Steph
costeph said:
Hello, after playing with my z90 (with the original rom that was Z90a40_USR_S118 international, bought in october 2015) I wanted to clean it up and make some updates. So I made my backups etc... Entered the recovery (not the green lenovo one wich is very limited) with hold vol - , I choosed to wipe (the phone was encrypted just to mention) all that I can and reset to factory, all was done but when it finished, it reboot and it stuck to initializing just after lenovo logo it reboot... initializing... and it s an inifinite loop. So I retryed to go to the maintenance recovery but it s not possible a black screen come and it reboot, I can go to the limited lenovo green recovery, but no factory reset, so I make the wipe datas etc... nothing... infinite reboot loop!
So I found some rom put them in the micro SD, go for an update.zip with the recovery, update work well but... initializing.... reboot...
Grrr, lenovo... So I take the big tools, installed a minimal win7 with qualcom drivers, lenovo ones, qpst. I tried many manipulation to enter the download mode with port com (I finaly managed multiple times with not the exact manipulation it s vol- + power + 10s and multiple spanning of the vol - button....) And I have succefully flashed multiple roms with qfil but with always the same results... initializing, reboot... I don t know where to search now, I someone can help me to find where to go, perhaps reflashing the recovery or I saw the .qnc in a russian forum but I can t understand one word.... 2 days of flashing make me hate my lenovo, my first brick with a phone . Any help?
Thanks,
sorry for my bad english
Steph
Click to expand...
Click to collapse
Hi,
here is my solution if can help.
I had on my vibe shot s208 rooted ROW. It stacked after SU update in boot loop.
1. I did wipe data without formatting from recovery mode (Vol+ and Vol- and Power button. When Logo is on release power button and hold Vol+ and Vol - until you are in recovery mode). STILL boot loop.
2. I did wipe data with formatting from the same menu. - STILL boot loop.
3. I did factory reset from recovery menu (Vol - and Power after logo is on release Power and hold Vol - until you get recovery mode) - STILL boot loop.
Then I did next:
1. I downloaded and installed QFIL (QPST_2.7.422) - I am not allowed to post links yet.
2. I have connected OTG adapter to phone. Phone was off.
3. then connected OTG to PC. It was some HDD activities but I did not hear any sound.
4. press Vol- for as long as something is going on - HDD activities. Then I think came up sound too - but not sure.
5. I had installed Qualcomm USB drivers from before I suppose.
6. Because I couldn't see my device as ...908 I disconnected and connected again usb cable... then I got my device as ...908 in device manager, but it was written "RECONNECTED" or similar in front of word "QUALCOM".
7. Then just follow instructions for QFIL. and ROM will be installed.
First I have installed INTERNATIONAL no root ROM. But because I needed phone to be rooted in order to use data recovery software I flashed again with s240 ROOTED. When I flashed second time I did not use OTG, just direct usb cable connection to PC, and my phone was again recognized after I reconnected usb cable and in device manger was "RECONNECTED" in front of word "QUALCOM".
Hello, thanks for replying. But I already tried all the roms with qfil, they were successfully installed as wtih miflash but I always got a initializing boot loop... Unfortunately I tried some other method, I successfully erase all partitions, I m now in 9006 mode with a long vibration on start and I cant do anything now No flashing works anymore... I ll try some stuff when I had a little time.
did you find a solution ?? , cause I have the same problem ... tried everything, adb or cwm recovery won't work cause my device is not rooted nor the usb debugging is on .. so am stuck with this "initializing loop".. flashing didn't solve it for me, I tried every ROM I could find, rooted or not .. nothing .... this problem happened with my phone after wiping user data and trying to restore QCN, cause before this problem I had another one with network services, tried to solve it, and here I am, from bad to worse
Hello,
I had the same problem. I tried with QFile and MiFlash but unfortunately without success. will you a track ?
I reinstalled the drivers QDLoader HS- USB Driver. I maintained volume + for 3 seconds , however, nothing happens ! (Before it worked ) I also tried adb reboot eld the prolème is the USBport phone is not known !
I followed the procedure of DejXDA carefully until the end staying press the VOL- the phone starts to recharging battery ... have you others sollutions ? thanks in advance.
Hey there !
Same problem for me... The solution may be to rebuild the partition table, but we need a working phone, and a backup with QPST.
Would anyone post a *.qcn file from his phone, made with QPST Software Download ? or a *.hex ?
And the user partitions ? Or a factory image (*.mbn) ?
Any gurus here, what would you advise for that problem ? Would using QPST properly work ?
Cheers !
Z90-7 (Z90a40) unbricked (at last...)
Hello!
After days and days of fails, my Z90-7 is unbricked!
How?
Just follow the OTG cable method, but copy in the SD card, in the sdfuse folder, this image:
Z90a40_S209_150716_ROW.qsb
You can download it from russian forum*, freely.
*I'm not allowed to post links, but enter the exact reference (Z90a40_S209_150716_ROW.qsb) in Google search (don't accept the Google's proposition to correct it), the link is the first answer. Use Google trad as I did if you don't speak russian .
Hello ,
I have a Lenovo vibe shot Z90-7
I wanted to set an international Rom 5.1 and now since it gets stuck on initializing indefinitely.
I have access to the recovery mode so I spend not to turn off the phone.
I Agency will proceed as this I put out the létélphone I press the volume + and I connect it to the ordidateur to put in download mode, but there is nothing after it launches in initializing .
So I essyer with presses of flight - and connects to the PC and it remains on the Lenovo logo.
In prériphérique manager there wrote lenovo ADB android.
Can not have Qualcomm hs -usb in the Port . even after installing the driver.
you have an idea what I can do?
Thank you
z90-7 not working
Hi,
i tried to install 20150619_VIBEUI_V2.5_1525_5.404.1_ST_Z90-7-Root_Phoenix rom on my lenovo vibe shot using Qfil , After Qfil finished flashing the mobile shutdown and It does not turn on anymore
and computer does not recognize it anymore.
what can I do??
Hi, i use the latest CM ROM for K910 for a quite long time. yesterday i dropped my phone and it crack my screen. was sending it for repair and now the phone wont load normally and it stays in CM loading screen and never boot up. With the cracked phone i use it for a day and sent it to the local shops to replace it.
so i managed to boot it into fastboot but sadly i cant do anything due to the bootloader is locked. all i can do is to unbrick it using the qualcomm resets which requires me to made some pin grounding and plug in the usb which allow me to use QFIL.exe to reset the phone into the very stock rom like in the factory.
after the reset it was working as it should but something is not right, the phone cant be used with its touchscreen, wont charge when it sleep and when ever the phone start to get dark when theres no input, it will stop charging and the screen wont turn on again. both when i boot the phone and when i turn off the phone and charge it. im not sure how to troubleshooting as i never encounter in my experiences. also, it will drain my battery. if i plug in my pc it will detect as Qualcomm HS-USB Diagnostics 9006 or Marshall London HS-USB Diagnostics 9006
anyone have solution for this or any idea?
Thanks in advance
AyieStyx said:
Hi, i use the latest CM ROM for K910 for a quite long time. yesterday i dropped my phone and it crack my screen. was sending it for repair and now the phone wont load normally and it stays in CM loading screen and never boot up. With the cracked phone i use it for a day and sent it to the local shops to replace it.
so i managed to boot it into fastboot but sadly i cant do anything due to the bootloader is locked. all i can do is to unbrick it using the qualcomm resets which requires me to made some pin grounding and plug in the usb which allow me to use QFIL.exe to reset the phone into the very stock rom like in the factory.
after the reset it was working as it should but something is not right, the phone cant be used with its touchscreen, wont charge when it sleep and when ever the phone start to get dark when theres no input, it will stop charging and the screen wont turn on again. both when i boot the phone and when i turn off the phone and charge it. im not sure how to troubleshooting as i never encounter in my experiences. also, it will drain my battery. if i plug in my pc it will detect as Qualcomm HS-USB Diagnostics 9006 or Marshall London HS-USB Diagnostics 9006
anyone have solution for this or any idea?
Thanks in advance
Click to expand...
Click to collapse
It shows HS-USB Diagnostics 9006 for you ! So do as I say :
1 . Turn off phone
2. press and hold vol up + vold down
3. connect to usb without powering up
4. You gets what you want !
R3 Pro (3GB/32GB, 2015817 version) came with some chinese/sellers custom ROM (and locked bootloader). It was heavy and bloated, so I decided to update it. Tried latest global stable (fastboot) ROM via miflash, flash was successful but that's was a lie - it stuck on mi logo...
Then I tried various other ROMs, global and developers, latest and older, some xiaomi.eu, manhit, etc. (for locked bootloader) and all I've got was either just a mi logo or mi logo with "powered by android" animation beneth. I left it for hours after flash and still nothing.
Then I found some ways to flash twrp, did that successfully, booted into it, wonder around in terminal and file manager, tried some recovery ROMs - but the result is the same - just logo or logo + animation.
I can get into fastboot (but it doesn't realy matters since bootloader is locked), download (EDL) mode, that Xiaomi menu (with Power and Vol+, with "shortcuts" to all the modes, hardware tests - btw. everything works there, etc.), twrp, charge battery (with some ROMs phone just gets warm and I know it's charging, there are no LED and/or animation, but in some everything works just like it should), but just can't boot into OS.
And I'm going nuts!
Here are some logs from the last ROM (i don't even know anymore which one is it) - pastebin.com/qaKVzxue and pastebin.com/dM3nEVj0
I'm not so experienced in looking at that but seems like every other thing in there, like cpu, i2c (touch/sensor), sound, battery, etc. is broken/faulty which is not true - everything was fine before update, and everything IS still fine according to inbuilt (xiaomi) hardware tests.
So somehow it seems that all the ido ROMs I tried are wrong for this device? Or am I missing something (quite possibly, I'm tired and pissed off)
Last night I did a backup of efs/nvram and then wiped internal memory/partitions, flashed latest global ROM, restored efs/nvram - phone stuck, but this time not on MI logo but freakin' penguin logo (like here en.miui.com/thread-377870-1-1.html). Same logo is for fastboot mode, no more bunny. Then flashed twrp and phone now shows mi logo with "powered by android" animation beneath, like before...
I don't know how this works with Xiaomi phones, but looks like it worked with some factory/seller special combination of ROM and bootloader. Then I did update and something stuck, maybe differences between ROM and bootloader, or some inside/hidden security mechanism that stops boot process? And because I can't find original firmware and/or bootloader is locked (maybe even updated?) it's now stuck...
Either that or some HW fault, but it would be insane that official ROM update with official tools and in factory download mode with full battery can cause such problem!
Can you go to twrp recovery?
Yes, like I said in the first post. I can do anything but boot android/MIUI. It's either because of locked bootloader or somehow official ROM installed officialy (via MiFlash in EDL mode) bricked phone, which is catastrophic bug i.e. epic design/implementation fail by Xiaomi.
Try this
https://forum.xda-developers.com/redmi-3/help/bootloop-bootloader-locked-options-t3331139
Sorry to intrude, I have pretty much the same problem.
Phone is stuck in bootloop and I can only access fastboot mode and EDL mode (but in EDL the phone does not connect to pc) and when I try to flash a stock ROM (since I know it is a software issue due to an unfortunate update) it says "locked device". So I tried to unlock it via MiUnlock... but phone cannot be verified 'cause "account not bound to this device" and obviously I cannot change any options since I cannot use my phone.
Please, help
it was happened to me about 3 days ago when i play around with the twrp & rooting thingy... tried everything from youtube to various forum solutions... just one link really works when you only have fastboot options and your phone bootloader is still unlocked. just follow the steps in the OP... key things here is downloading the tool to read your phone as mentioned in the OP i.e [TOOL]Minimal ADB and Fastboot [1-6-17]
1) Download Tool -> https://forum.xda-developers.com/showthread.php?t=2317790
2) Follow all the steps in the OP -> http://en.miui.com/thread-277276-1-1.html
3) Enjoy your phone from back from the dead.. LOL!
4) Remember here, the key is NEVER GIVE UP and PATIENT!
NOTE : The Device will start, wait till completion , it can take up to 10 Minutes. -> for me around 15-20 minutes for I have flashed the current beta rom of MIUI8 7.6.8
cheers, guys!
blx-
I had a similar situation.
Officially unlocked boot loader. Flashed TWRP using fastboot. Only got the mi logo and a boot loop on start up.
Could not turn on. Could not boot into TWRP.
When the phone was boot looping I could still get into fastboot mode by holding power+volume down.
I booted from fastboot mode into TWRP by opening the command prompts and using
"fastboot boot twrp2.img"
That got the phone available from windows explorer. I was able to move a new ROM image to the SD card and install from TWRP.
Currently running lineage 14.1 -20190112.
I lost a bunch of **** but my phone seems to turn on for the moment.
Note, I still cannot boot into TWRP using the phone only. I can only boot in from fast boot as above.
I'm currently having issue with my phone, Redmi Note 3 Pro Kenzo(snapdragon 650) charged my phone overnight after completely drained it and the next morning i realized that it's on boot loop.
I tried dozens of method since the past 72 hours, none of them works. My phone run on stock miui 8 rom, didn't turn on the dev mode/debugging so basically just a pure stock out of the box phone with 0 tweaks.
It loops without the android logo below it. Just the MI logo in the middle of the screen and it reboot every 10-15 seconds or so.
I am able to run on fastboot mode (volume down+power on button) then i hook it up to my computer, used a patch to boot it on EDL mode and flash the stock fastboot rom using MiFlash and it states that i have successfully flash the rom on the phone. But when i turn it on, it loops on the MI logo again..
Tried dozens of method, flashed the emmc file and etc but none of them works.
Even mod on xiaomi forum gave up on me and ended up saying that i've roasted my logic board lol
But I read a thread on someone who had the same problem with mine but he have unlock his bootloader and get his phone back to life by flashing the twrp recovery.
When i try to hook up my phone with command prompt, running on fastboot mode it detects my phone when use the "fastboot devices" but when i use the "adb" command it stated that my computer didn't detect my device.
any thoughts?
rlly need some help here guys :/
Hello everyone, got this bricked phone with asus logo stuck, tried to unbrick with qfil and stock firmware, and i was getting errors, one of them is finished sector adress ****, and i cant get out from edl mode with holding buttons, none of them reboot it, only power button can restart edl mode if i hold it for 30+ secs, led indicator, screen, nothing work, with removed battery still recognizes as Hs usb ....... 9008, what can i do to exit edl mode?, and how can i flash an rom? P.S phone was in water about year ago.
(Sorry for my english):crying:
P.S.S before stuck, when i was getting to fastboot, flash tool was telling me that my phone is -1% battery