Related
Hi guys,
I really do not want to install KIES as it looks to me a HUGE piece of bloatware.
Anyways, to make the story short, I think I got all S2 drivers installed the clean way but I need to make sure everything is OK, before I root my phone.
This is what I did (might be useful for others):
First, I plugged the phone through USB on my Windows 7 SP1 64bits box. It detected right away the phone and installed a set of drivers, except the CDC serial. I was able to see and browse the phone content (deleted some .ipk file I downloaded by accident also):
In Device Manager, I had flagged the CDC Serial:
I said, OK... let's get into Odin mode (Vol Down + Home + Power) and see what happens. To my surprise, once Odin was displayed on my phone, Windows detected new hardware and downloaded then actually installed the right drivers???
After the drivers were installed, I powered down the phone, removed the USB cable and start it in normal mode. Once the phone was powered up, I plugged back the USB cable and the CDC Serial was missing again into Device Manager! I powered down again the phone and start it in Odin mode, the CDC Serial driver showed as being properly installed... go figure, heh.
Finally, the question: I would like to know if there is a method to check if Odin software communicates properly with the phone, before I attempt the rooting. I don't care if I get a flagged CDC Serial when the phone is in normal mode.
I really hope all drivers are properly registered, so I don't need to install the creepy KIES... as a side note, if you extract the executable, you will find inside the archive a cab file that contains a huge set of drivers (C:\kies_win\CabFile\USB Driver\SAMSUNG_USB_Driver_for_Mobile_Phones.exe.cab). I extracted the .cab file and ran a driver upgrade in Device Manager for the CDC Serial with the phone in normal mode, it did not do jack.
Thanks for your help.
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
your not the only one with this problem i have it too with same mt6575 someone help please
Need to uninstall device and reinstall drivers
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
ronbo76 said:
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
Click to expand...
Click to collapse
Your USB program does give a lot of information I have never seen before, but I still haven't been able to figure out how to get the driver to load.
thanks, John
I'm having the same problem installing the MT6575 USB VCOM drivers. Is there a workaround to get this installed? I"m using WIN 6 64bit
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
ivy13 said:
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
Click to expand...
Click to collapse
Tried your first method but still get Code 10 error. Could not understand your second method. Please help. Me device is Qmobile Noir A2
hye.. any progress? am having the same issue.. just for MTK6575 com port driver
Just made my Amoi N820 work
So happy
You get Code 10 becouse your windows couldn't recognize the driver but that's irrelevant becouse flashing will work
No solution?
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
orion~X said:
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
Click to expand...
Click to collapse
i have thet problem to.
is ther solution?
I HAVE SOLUTION FOR THIS PROBLEM!!
Just ignore the error Code 10! Start the SPFlashtool and load the scatterfile, click on download and connect your switch off Phone with the computer. It will work fine.
Having the Same Problem
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Hi.
me test for me not work.
iphone 4s.
plz help me.
hihi2u2 said:
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Click to expand...
Click to collapse
Did you ever get this problem solved as I have the same issue with an MTK 6592 chip based phone?
I have the same problem too.
Installation of Media Tek preloaded drivers gives me Code 10 error.
Has anyone found the solution?
my phone is totally dead without power now after I tried to flash with SP Flash tool using correct ROM. I noticed in device manager that there is a CODE 10 error in mediatek preloader usb driver.. is this the culprit? my phone can no longer be detected now in SPFlash or MTK Droid tools... so hopeless... this is a brandnew phone I bought to be given as gift to my cousin...
I did it! I did it! I did it!
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
I've been struggling with my UMI Rome for days. It has/had the black screen problem, sometimes won't enter recovery mode, sometimes wouldn't allow charge, sometimes works just fine (yesterday). Last night i mistakenly cut off power during a battery recharge. -- today it has all the above problems (bricked) so I am trying doing a flashing again using the tutorials and tools on the Tehnotone.com site. Sintetix's reply above helps me at least have a better clue on what is going on. Wish me luck! BTW, I am using a Dell Windows 10 pc. (Results to be reported here.)
Sintetix said:
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
Click to expand...
Click to collapse
I tried what you said. It wouldn't install properly. It kept saying error (code 10) and showed in device management with a caution sign every time I installed the driver. I disabled the forced driver signature thingamabop but it still does it. I guess I'm screwed. Has anyone else fixed this?
Hi All,
I am having an issue with my S4 that when I plug them into my computer I get USB device not recognized. I have searched the forum for the past 2 days trying all kinds of different solutions the major one was changing my USB/charging port board on my phone.
I need to ODIN my device to an MJ7 image. At first I got the error and did a factory reset through safestrap recover. Still got the error so I did an advance wipe of every option. (Looking back shouldnt have done that) That took away my recovery, but I can get to download mode, but its not detected by my computer to use ODIN with. So I am stuck without a custom recovery without the ability to boot into anything.
Here is what I have tried so far:
1. Reinstall/uninstall drivers, reinstall/uninstall kies.
2. Changed USB ports on computer.
3. Changed USB cables
4. Changed computers from Win 8 x64 to Win 7 x64.
5. Changed computer to my MACbook using Heimdall.
6. Changed USB charging port board on my phone.
7. Tried everything again. *Still doesnt detect it*
Any ideas that I havent done already, or how to fix? I do have nandroid backup of my ROM, but dont have a custom recovery to flash it.
Cant ODIN back cause its not detected by my computer. Thanks in advance for your help.
Is USB debugging still checked on phone? You must use the USB cable provided with phone...
safestrap enabled, Hyperdrive driven
Thanks for the reply. I cant select USB debug on my phone because my phone does not boot into the main OS, it is stuck at the samsung custom padlock screen. The USB debug option was on when the OS was installed though. My phone will only boot into stock recovery and into download mode. I tried to use the original USB cable provided with the phone as I read this could be the problem, but I tried 4 other ones too and phone still gets detected as "Unknown Device" in device manager, so ODIN cant even see phone in download mode to restore. I have tried to install KIES and the Samsung Mobile phone drivers 1.5.x.x drivers. Just read somewhere where someone had this issue and installed Samsung mobile phone driver v1-4-6-0 so I am trying that now.
odlay75 said:
Thanks for the reply. I cant select USB debug on my phone because my phone does not boot into the main OS, it is stuck at the samsung custom padlock screen. The USB debug option was on when the OS was installed though. My phone will only boot into stock recovery and into download mode. I tried to use the original USB cable provided with the phone as I read this could be the problem, but I tried 4 other ones too and phone still gets detected as "Unknown Device" in device manager, so ODIN cant even see phone in download mode to restore. I have tried to install KIES and the Samsung Mobile phone drivers 1.5.x.x drivers. Just read somewhere where someone had this issue and installed Samsung mobile phone driver v1-4-6-0 so I am trying that now.
Click to expand...
Click to collapse
Tried Samsung Mobile phone drivers version 1.4.6.0 and still the same outcome "USB device not recognized". I went down to a local electronics store and bought two different brand microUSB data cables. Tried them both along with my original one from samsung, and still the same result. Any other ideas??
Anyone else have any ideas? Thinking of sending it in and having it JTAG'ed back to stock. Can anyone recommend any services? Heard mobiletechvideos is good.
odlay75 said:
Anyone else have any ideas? Thinking of sending it in and having it JTAG'ed back to stock. Can anyone recommend any services? Heard mobiletechvideos is good.
Click to expand...
Click to collapse
Go to Saferoot thread in dev forum...your answer may be there
safestrap enabled, Hyperdrive driven
Once you got into android modding, an unrooted phone becomes almost useless.
Now my problem is that I´ve got one.
Couple of days ago my Elephone P9000 arrived from amazon but I can´t connect it to a PC since it says that no device is detected.
Yes, the drivers are installed properly!
I thought that isn´t a problem because there is Kingroot.
Turns out the following rooting apps don´t work for me:
Kingroot (Kingoroot), iRoot, z4root, Framaroot, Towelroot, Oneclickroot, Universal Androot, Root Genius, Baidu
Custom Recovery isn´t installed because, of course, no root.
Now how do I root?
ThisIsMyMaster said:
Once you got into android modding, an unrooted phone becomes almost useless.
Now my problem is that I´ve got one.
Couple of days ago my Elephone P9000 arrived from amazon but I can´t connect it to a PC since it says that no device is detected.
Yes, the drivers are installed properly!
I thought that isn´t a problem because there is Kingroot.
Turns out the following rooting apps don´t work for me:
Kingroot (Kingoroot), iRoot, z4root, Framaroot, Towelroot, Oneclickroot.
Custom Recovery isn´t installed because, of course, no root.
Now how do I root?
Click to expand...
Click to collapse
The first thing you need to accomplish is to get your PC to recognize your phone, rooting from there is going to make life easier, but yes, I know you already know that. If your using windows 10, maybe check this thread out on Elephone Forum:
http://bbs.elephone.hk/forum.php?mod=viewthread&tid=12240&page=1&ordertype=1#pid129322
jotei66 said:
The first thing you need to accomplish is to get your PC to recognize your phone, rooting from there is going to make life easier, but yes, I know you already know that. If your using windows 10, maybe check this thread out on Elephone Forum:
(link removed)]
Click to expand...
Click to collapse
That´s the tutorial that I was going to do but when my phone is shut down, my pc doesn´t detect the device and flash tool neither.:crying:
ThisIsMyMaster said:
That´s the tutorial that I was going to do but when my phone is shut down, my pc doesn´t detect the device and flash tool neither.:crying:
Click to expand...
Click to collapse
Firstly is your PC finding your phone ok with the PC on? If yes.. all good - if no you need to sort this out first.
Then, ensure you have installed the MTK driver on your PC (these are the Media Tek drivers which will find your phone when it is off) instructions here:
https://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
Then flashtools should work fine with your phone off.
Just a tip using FlashTools (Im on windows 10 - I dont know if this applies to other windows)
In flashtools, press download first (without phone connected), give it 5 secs and then connect your phone to your PC with the volume up button pressed at the same time. Once you see FlashTools starting to flash your phone, release the volume button. I have to do this all the time in order for my phone to be found on Windows 10.
jotei66 said:
Firstly is your PC finding your phone ok with the PC on? If yes.. all good - if no you need to sort this out first.
Then, ensure you have installed the MTK driver on your PC (these are the Media Tek drivers which will find your phone when it is off) instructions here:
https://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
Then flashtools should work fine with your phone off.
Just a tip using FlashTools (Im on windows 10 - I dont know if this applies to other windows)
In flashtools, press download first (without phone connected), give it 5 secs and then connect your phone to your PC with the volume up button pressed at the same time. Once you see FlashTools starting to flash your phone, release the volume button. I have to do this all the time in order for my phone to be found on Windows 10.
Click to expand...
Click to collapse
To start of, I am using Windows 10 as you do.
When I connect my phone when it´s turned on, I get the small icon in the taskbar that allows me to remove the device safely or open devices and printer.
There, my device is put to a section called not specified and it has a small yellow icon.
Only is it called "P9000" which is alright.
Windows explorer acts like no device is connected at all.
When I connect my phone as it is turned off, I still get the notification "USB Device wasn´t recognized." and
windows explorer still doesn´t care as well as the flash tool.
The link you gave me isn´t the one I previously used to install the drivers so I gave it a try.
There are two different ways mentioned in the posts #1 and #4 so I started with the first one.
(Spoiler: Both don´t work for me!)
Everything worked until a step almost at the end where I am told to connect my off-switched phone to the pc.
The tutorial tells me that there should now be a preloader unknown device or something at Device Manager > Ports (COM & LPT) that I would need to proceed further.
I didn´t get that one.
Dead end for me so I went on to the next tutorial in post #4.
In that post I am told to remove a MTK USB Port at Device Manager > Ports (COM & LPT) right after installing the .inf driver files (Yes, I installed the 64 bit version and do have a 64 bit PC).
Ignoring that step didn´t help any of the problems I had before so I got a dead end here, too.
The "Volume-Up-Trick" did help me neither, probably cause of the not working drivers.
ThisIsMyMaster said:
To start of, I am using Windows 10 as you do.
When I connect my phone when it´s turned on, I get the small icon in the taskbar that allows me to remove the device safely or open devices and printer.
There, my device is put to a section called not specified and it has a small yellow icon.
Only is it called "P9000" which is alright.
Windows explorer acts like no device is connected at all.
When I connect my phone as it is turned off, I still get the notification "USB Device wasn´t recognized." and
windows explorer still doesn´t care as well as the flash tool.
The link you gave me isn´t the one I previously used to install the drivers so I gave it a try.
There are two different ways mentioned in the posts #1 and #4 so I started with the first one.
(Spoiler: Both don´t work for me!)
Everything worked until a step almost at the end where I am told to connect my off-switched phone to the pc.
The tutorial tells me that there should now be a preloader unknown device or something at Device Manager > Ports (COM & LPT) that I would need to proceed further.
I didn´t get that one.
Dead end for me so I went on to the next tutorial in post #4.
In that post I am told to remove a MTK USB Port at Device Manager > Ports (COM & LPT) right after installing the .inf driver files (Yes, I installed the 64 bit version and do have a 64 bit PC).
Ignoring that step didn´t help any of the problems I had before so I got a dead end here, too.
The "Volume-Up-Trick" did help me neither, probably cause of the not working drivers.
Click to expand...
Click to collapse
Ok first things first, lets make sure your P9000 is fine with your phone on. You said:
When I connect my phone when it´s turned on, I get the small icon in the taskbar that allows me to remove the device safely or open devices and printer. There, my device is put to a section called not specified and it has a small yellow icon.
Only is it called "P9000" which is alright.
Click to expand...
Click to collapse
(make sure in dev options on your phone USB debugging is ON and USB config is MTP)
So from that you simply need to (In Device Manager) right click > Update Driver Software > Browse My PC for Driver Software > Let me pick from a list of device drivers from my PC > then choose MTP USB Device
Once windows installs this, a box should pop up showing your P9000 internal storage and SD Card (if you have one in phone)
To ensure that your PC is now finding your phone ok, restart PC and plug your phone in - you should be prompted by windows to choose a default action when this device is connected (I choose transfer files or something similar). Then everytime you connect your phone, a box will pop up showing allowing you to access your P9000.
Now onto when your P9000 is switched off... (the important part for flashing etc)
I followed the instructions at post #4 as I believe due to the anniversary update on windows 10 (the January update I believe) .. if you do not have the January update installed on your PC you would use the instructions #1
Don't worry too much if you receive "USB device not recognised" initially, (from what I have understood this is normal with the Anniversary addition of windows 10) it should disappear after few seconds or so. From what I worked out following post #4 you are kinda installing a MTK device (just so you can install the drivers) and then uninstalling that device BUT keeping the drivers installed (its VERY important when you uninstall the device you untick the delete drivers too, otherwise you have essentially deleted the MTK drivers & would have to start from scratch from post #4)
For me, when I connect my p9000 when its off it still shows "USB device not recognised", then after a few seconds this goes away and I dont have any errors under Device Manager > Ports (COM & LPT) & flashtools works fine as long as I press vol up as I connect my phone.
Hope this helps, I had a headache when I tried to install MTK drivers with my windows 10 (Anniversay Update Edition) - good luck, it was kinda trial and error
jotei66 said:
Ok first things first, lets make sure your P9000 is fine with your phone on. You said:
(make sure in dev options on your phone USB debugging is ON and USB config is MTP)
So from that you simply need to (In Device Manager) right click > Update Driver Software > Browse My PC for Driver Software > Let me pick from a list of device drivers from my PC > then choose MTP USB Device
Once windows installs this, a box should pop up showing your P9000 internal storage and SD Card (if you have one in phone)
To ensure that your PC is now finding your phone ok, restart PC and plug your phone in - you should be prompted by windows to choose a default action when this device is connected (I choose transfer files or something similar). Then everytime you connect your phone, a box will pop up showing allowing you to access your P9000.
Now onto when your P9000 is switched off... (the important part for flashing etc)
I followed the instructions at post #4 as I believe due to the anniversary update on windows 10 (the January update I believe) .. if you do not have the January update installed on your PC you would use the instructions #1
Don't worry too much if you receive "USB device not recognised" initially, (from what I have understood this is normal with the Anniversary addition of windows 10) it should disappear after few seconds or so. From what I worked out following post #4 you are kinda installing a MTK device (just so you can install the drivers) and then uninstalling that device BUT keeping the drivers installed (its VERY important when you uninstall the device you untick the delete drivers too, otherwise you have essentially deleted the MTK drivers & would have to start from scratch from post #4)
For me, when I connect my p9000 when its off it still shows "USB device not recognised", then after a few seconds this goes away and I dont have any errors under Device Manager > Ports (COM & LPT) & flashtools works fine as long as I press vol up as I connect my phone.
Hope this helps, I had a headache when I tried to install MTK drivers with my windows 10 (Anniversay Update Edition) - good luck, it was kinda trial and error
Click to expand...
Click to collapse
I am running the Anniversay Update Edition and don´t get an popup window when connecting my phone turned on.
As far is I can tell, a working connection with the device running is more important in the first place.
Now I don´t quite understand your instructions at this point:
jotei66 said:
So from that you simply need to (In Device Manager) right click > Update Driver Software > Browse My PC for Driver Software > Let me pick from a list of device drivers from my PC > then choose MTP USB Device
Click to expand...
Click to collapse
In Device Manager right click, but where?
Blank space? Definetly not.
According to the linked tutorial, I´d have to right click on something like "unknown device" or something similar.
But that doesn´t show up in my list.
In the next section you said:
jotei66 said:
you are kinda installing a MTK device (just so you can install the drivers) and then uninstalling that device BUT keeping the drivers installed
Click to expand...
Click to collapse
I can understand the point but after installing that driver package, there is no MTK device in my device manager that I could uninstall.
I seriously need to thank you for wasting so much time on me:angel:
When you plug your p9000 (while its turned on) into your laptop/pc... in Device Manager, probably under Universal serial Bus Controllers do you see a unknown device, or anything with a question mark / unknown device beside it ? If so, that's where you right click and follow instructions above to get your PC to recognize your handset. At this point just concentrate on getting pc to recognise while its on, then hopefully we can then move to setting up when its off.
I seriously need to thank you for wasting so much time on me
Click to expand...
Click to collapse
lol its all cool
PS: Just to make sure, in device manager, press View from top menu and "show hidden devices".. maybe it could be hidden?
jotei66 said:
When you plug your p9000 (while its turned on) into your laptop/pc... in Device Manager, probably under Universal serial Bus Controllers do you see a unknown device, or anything with a question mark / unknown device beside it ? If so, that's where you right click and follow instructions above to get your PC to recognize your handset. At this point just concentrate on getting pc to recognise while its on, then hopefully we can then move to setting up when its off.
lol its all cool
PS: Just to make sure, in device manager, press View from top menu and "show hidden devices".. maybe it could be hidden?
Click to expand...
Click to collapse
I can´t believe how stupid I am...
jotei66 said:
Just to make sure, in device manager, press View from top menu and "show hidden devices".. maybe it could be hidden?
Click to expand...
Click to collapse
Well, that solved all of my problems...
Almost...
Drivers are fully working for me now so I wanted to flash TWRP with SP Flash Tool to be able to flash the superuser .zip file.
Since drivers work now, flash tool started flashing and gave me the error you can see in the attached screenshot.
Fortunately, my phone isn´t bricked or anything.
Edit: After a couple of reboots of all my devices, I get back to where I was before: USB Device wasn´t recognized and Flash Tool doesn´t do anything.
ThisIsMyMaster said:
I can´t believe how stupid I am...
Well, that solved all of my problems...
Almost...
Drivers are fully working for me now so I wanted to flash TWRP with SP Flash Tool to be able to flash the superuser .zip file.
Since drivers work now, flash tool started flashing and gave me the error you can see in the attached screenshot.
Fortunately, my phone isn´t bricked or anything.
Click to expand...
Click to collapse
All cool & its an easy thing to miss when your not looking for it (or for that matter if you dont know that menu even existed)
That error is a preloading error, I'm assuming your flashing TWRP Recovery and like you I had similar issue - I shared a simple solution here that worked for me here (it should work fine as long as you are on Stock Elephone 2016810 Base onwards so I believe, Elephone changed the preloader or something like that in later ROMS)
So Basically, you download the Stock Elephone 2016810 Base ROM from HERE & unzip
Grab Flash Tools ver v5.1612 (if your not using that version) HERE - https://www.androidfilehost.com/?fid=24591000424940027
Then download TWRP_3.0.2.8.zip HERE & unzip
Copy the the "MT6755_Android_scatter" & "recovery.img" from TWRP_3.0.2.8 folder into the Elephone_P9000_2016810 Rom folder.
In Splash Tools, first flash the Elephone_P9000_2016810 Rom open "MT6755_Android_scatter" from _810 file & ensure the recovery section location points to "recovery.img" in the _810 folder also
Once your stock _810 ROM is flashed successfully, you then flash TWRP (with only recovery ticked) and ensure the recovery location points to "recovery_TWRP_3028_P9000" and your TWRP should flash fine. Make sure your using Flash Tools ver v5.1612, that worked fine for me.
There maybe an easier solution someone can point you too, but I know this worked for me no problems - you should now have TWRP recovery on stock _810 ready for you to flash your chosen ROM
jotei66 said:
All cool & its an easy thing to miss when your not looking for it (or for that matter if you dont know that menu even existed)
That error is a preloading error, I'm assuming your flashing TWRP Recovery and like you I had similar issue - I shared a simple solution here that worked for me here (it should work fine as long as you are on Stock Elephone 2016810 Base onwards so I believe, Elephone changed the preloader or something like that in later ROMS)
So Basically, you download the Stock Elephone 2016810 Base ROM from HERE & unzip
Grab Flash Tools ver v5.1612 (if your not using that version) HERE - https://www.androidfilehost.com/?fid=24591000424940027
Then download TWRP_3.0.2.8.zip HERE & unzip
Copy the the "MT6755_Android_scatter" & "recovery.img" from TWRP_3.0.2.8 folder into the Elephone_P9000_2016810 Rom folder.
In Splash Tools, first flash the Elephone_P9000_2016810 Rom open "MT6755_Android_scatter" from _810 file & ensure the recovery section location points to "recovery.img" in the _810 folder also
Once your stock _810 ROM is flashed successfully, you then flash TWRP (with only recovery ticked) and ensure the recovery location points to "recovery_TWRP_3028_P9000" and your TWRP should flash fine. Make sure your using Flash Tools ver v5.1612, that worked fine for me.
There maybe an easier solution someone can point you too, but I know this worked for me no problems - you should now have TWRP recovery on stock _810 ready for you to flash your chosen ROM
Click to expand...
Click to collapse
I´m going to try this now.
Do I have to go back to Stock 20160810 if I have 20161107?
Do I have to go back to Stock 20160810 if I have 20161107?
Click to expand...
Click to collapse
I guess if you download the 20161107 ROM it should work, I'm really unsure, its a newer ROM so I guess it should
jotei66 said:
I guess if you download the 20161107 ROM it should work, I'm really unsure, its a newer ROM so I guess it should
Click to expand...
Click to collapse
It didn´t work.
I did all the steps you´ve told me and ended up with the exact same problem I´ve experienced before: USB Device not recognized and SP Flash Tool doesn´t do anything after pressing the download button.
I was going to reinstall the drivers like you told me form post #4 here: https://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
That didn´t do anything, I still have the same problem of my pc not recognizing my phone.
At least connecting my phone when it´s running works now.
you have to press and keep vol + when connecting the turned off phone to the computer after clicking download in FlashTools.
Regards
Fran Montero said:
you have to press and keep vol + when connecting the turned off phone to the computer after clicking download in FlashTools.
Regards
Click to expand...
Click to collapse
Tried it, didn´t help
ThisIsMyMaster said:
Tried it, didn´t help
Click to expand...
Click to collapse
MMmmm .. have you tried a different USB port? maybe a different lead if you have one? (I have two leads and I know one doesnt work for me, dunno why)
Also, after pressing download in SplashTools.. count to say 7-10 secs and then press Vol UP and connect your phone.... (I know this sounds bit stupid, but it works for me, if I connect straioght away I get errors too ref driver )
jotei66 said:
MMmmm .. have you tried a different USB port? maybe a different lead if you have one? (I have two leads and I know one doesnt work for me, dunno why)
Also, after pressing download in SplashTools.. count to say 7-10 secs and then press Vol UP and connect your phone.... (I know this sounds bit stupid, but it works for me, if I connect straioght away I get errors too ref driver )
Click to expand...
Click to collapse
No, that doesn´t help either.
I think it has to do something with installing the drivers cause after installing them, in Device Manager no new drivers are displayed except for two Mediatek Preloader USB VCOM Port (COM5) and (COM6).
But those only become visible when I check "show hidden devices".
The tutorial said that some more things should have been installed but I didn´t get any error messages so I don´t understand what shouldn´t have worked.
Sorry Im at a loss really, maybe follow this tutorial my brother followed to reinstall the MTK and try again with all the above steps, good luck
https://www.youtube.com/watch?v=NbJCbdfPlF8
Make sure your PC is in driver signature disable mode when flashing etc btw
jotei66 said:
Sorry Im at a loss really, maybe follow this tutorial my brother followed to reinstall the MTK and try again with all the above steps, good luck
https://www.youtube.com/watch?v=NbJCbdfPlF8
Make sure your PC is in driver signature disable mode when flashing etc btw
Click to expand...
Click to collapse
Didn´t help either.
Current state:
Phone On > Everything working, I get the popup window and data transfer works :good:
Phone Off > USB wasn´t recognized, Flash Tool isn´t working, no recognition in windows explorer, phone is charging, vol+ doesn´t help
MTP and USB Debugging are activated
While installing the drivers I got no error messages and everything looked same as in the tutorial
ThisIsMyMaster said:
Didn´t help either.
Current state:
Phone On > Everything working, I get the popup window and data transfer works :good:
Phone Off > USB wasn´t recognized, Flash Tool isn´t working, no recognition in windows explorer, phone is charging, vol+ doesn´t help
MTP and USB Debugging are activated
While installing the drivers I got no error messages and everything looked same as in the tutorial
Click to expand...
Click to collapse
Good to hear you can atleast use your phone to transfer etc while on
Just curious (although Im sure you have followed the video / other tutorials to the letter) but
(1) did you ensure when following video tut that when uninstalling the legacy device you unticked the driver box to ensure the drivers were actually kept installed?
(2) Check Device Manager, under the Ports (COM & LPT) section and remember you shouldn't have anything referring to a MTK device in there - ie like MTK USB Port (Com 3) ? (If you have it needs uninstalling)
(3) Seems obvious I know but you are connecting your phone and using FlashTools when your Windows Driver Enforcement is disabled? ( Literally restarting with advanced options & choosng Disbale Driver Enforcement) Many users think once you have installed the driver you can use it with Windows Drivers enforcement enabled, but you have to be in disabled mode.
Finally if you doubled checked all of those, then maybe try a different version of FlashTools (worth a try) and also try running FlashTools as Administrator when you open it - good luck
I'm trying to install stock rom in my OPPO A57 as it went dead and doesnt turn on. While going through the process i had to install Qualcomm USB drivers . After installing the drivers, there was no connection as it didnt showed up in my device manager. Went through several fix videos on youtube. Many of those tutorial videos showed to update the QHSUSB_bulk (found in device manager) with the qualcomm drivers. Unfortunate thing is there is no QHSUSB_bulk in device manager. How do i install the drivers? why QHSUSB-bulk is not showing in device manager? Help please asap.
toposexxum said:
I'm trying to install stock rom in my OPPO A57 as it went dead and doesnt turn on. While going through the process i had to install Qualcomm USB drivers . After installing the drivers, there was no connection as it didnt showed up in my device manager. Went through several fix videos on youtube. Many of those tutorial videos showed to update the QHSUSB_bulk (found in device manager) with the qualcomm drivers. Unfortunate thing is there is no QHSUSB_bulk in device manager. How do i install the drivers? why QHSUSB-bulk is not showing in device manager? Help please asap.
Click to expand...
Click to collapse
By any chance do you have another computer, if you do, try on that one. If not tho, try replacing the USB cable or check if the micro USB port to see if it is damaged somehow, it is always important to check those things first.
I personally own the device and have never faced a issue and even went ahead and installed CM 13.0 on it.
Pleaaaaas
Help me for root my device
S7
I'm going to give u info that you rarely find about this issue.
many users didn't realize that that port will only be active for a very short time. Pressing Power+vol up+vol down at the same time SHOULD ONLY BE DONE AFTER you have load all necessary files into QFIL or DownloadTool, it should the last thing u do.
It is ok to let the device connected to your pc while setting up qfil etc, but your phone must be in shutdown mode.
now open device manager, then press all three buttons at the same time, release aftee you see device manager is showing sign of detection of the qualcomm port, do not wait more than 4 seconds to press DOWNLOAD. And click DOWNLOAD on the QFIL app. I suggest using QFIL v1.0.0.2
after that your phone will reboot normally. QFIL will look like it's still not finish, but it actually had finished flashing so you can close it.