When i was updating the twrp i managed to hard brick my phone, it just shows the 1+ logo and "powered by android" when turned on. if i hold the power button and volume up it shows the cyanogenmod logo and "fastboot mod" and stays there. If i hold power button and volume down it just shows the 1+ logo without the "powered by android".
i followed this guide https://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
completed all the steps but the installed program cant recognise my phone when i plug it in.
When its in fastboot mode logo i can see it in device manager under portable devices listed as "ONE E1001" (it has a yellow ! triangle next to it)
When i try to turn the recovery (powerbutton+volume down) where it shows just the 1+ logo with no "powered by android" i can see it in the device manager under android phone as "Android Bootloader Interface"
When i just turn it on where it does display "powered by android" i can see it same as in fastboot mode, as "ONE E1001" under portable devices, (a yellow ! triangle appears after some time too)
i tried a similar guide here: https://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
did everything, i have like 5 driver now from all the guides, i think all of them work, i just cant manage to get the programs to realize when the phone is pluged in. Is it possible that something is still wrong with the drivers?
pls help );
PlsHelpMeee said:
When i was updating the twrp i managed to hard brick my phone, it just shows the 1+ logo and "powered by android" when turned on. if i hold the power button and volume up it shows the cyanogenmod logo and "fastboot mod" and stays there. If i hold power button and volume down it just shows the 1+ logo without the "powered by android".
i followed this guide https://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
Click to expand...
Click to collapse
You're talking about Cyanogenmod logo. What was on your phone before? What did you do exactly?
Are you sure you know how to use Fastboot?
"fastboot oem device-info" output?
And then explain precisely at what step you have error.
Kéno40 said:
You're talking about Cyanogenmod logo. What was on your phone before? What did you do exactly?
Are you sure you know how to use Fastboot?
"fastboot oem device-info" output?
And then explain precisely at what step you have error.
Click to expand...
Click to collapse
i had CM12 before i tried to upgrade, i managed to go through the entire first guide now, the CM logo isn't appearing anymore, now its the 1+ logo and below it "fastboot mode" the drivers were a problem after all
now im stuck at the new recovery that is installed and cant install the ROM from it, even my old one that i had before all of this (CM12) that i have on my sd card.
OK, so you flash something incompatible.
After CM13 or so, the bootloader have to be upgraded and then you have to use a version compatible with it.
First look with fastboot command I give if BL still unlocked.
Do you know how to use fastboot commands?
Kéno40 said:
OK, so you flash something incompatible.
After CM13 or so, the bootloader have to be upgraded and then you have to use a version compatible with it.
First look with fastboot command I give if BL still unlocked.
Do you know how to use fastboot commands?
Click to expand...
Click to collapse
kind of, "fastboot oem device-info" output is
(bootloader) Device tampered: true
(bootloader) Device unlocked: false
(bootloader) Charger screen enabled: false
(bootloader) Display panel:
(bootloader) console_enabled: 0
(bootloader) exec_console_unconsole: 0
OKAY [ 0.010s]
finished. total time: 0.011s
if i could install the twrp from here i could install the ROM too i think, is there a guide to do so while stuck like this?
"fastboot oem unlock" gives me
FAILED (remote: oem unlock is disabled)
finished. total time: 0.009s
i cant use adb commands, in the command prompt my computer doesent even see the device when i type "adb devices", i think its because oem, debuging, isnt turned on but i cant turn it on if i cant install a ROM and check it "on" in the settings of the androis OS.
all i can use are fastboot comands since my computer can see it as a fastboot device while not as a adb device. i have a bricked phone with a locked bootloader i think.
BL is locked so only solution is mega unbrick guide.
I never tried but oos 3.1.4 won't flash either...
Kéno40 said:
BL is locked so only solution is mega unbrick guide.
I never tried but oos 3.1.4 won't flash either...
Click to expand...
Click to collapse
i did the mega unbricked guide, this one ==> https://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
i have the recovery dom the guide installed but it cant install any ROMs or the twrp, im trying to install them over fastboot but it also cant be done because my device is locked and i cant flash anything remotely. I also cant use adb for some reason because the command prompt cant see my phone under "adb devices". is there anything i can install with that recovery? i just stuck, spent so much time and still nothing :crying:
i think adb devices dont show because usb debugging is not turned on, i dont know how it can be turned on without and actual operating system on the phone..
THis guide push you back with OnePlus recovery and OOS.
That's not what you have?
You did something wrong...
At which step does it stop?
A few day ago, one of the file ws missing. Do you have it all?
---------- Post added at 10:43 PM ---------- Previous post was at 10:43 PM ----------
THis guide push you back with OnePlus recovery and OOS.
That's not what you have?
You did something wrong...
At which step does it stop?
A few day ago, one of the file ws missing. Do you have it all?
Kéno40 said:
THis guide push you back with OnePlus recovery and OOS.
That's not what you have?
You did something wrong...
At which step does it stop?
A few day ago, one of the file ws missing. Do you have it all?
---------- Post added at 10:43 PM ---------- Previous post was at 10:43 PM ----------
THis guide push you back with OnePlus recovery and OOS.
That's not what you have?
You did something wrong...
At which step does it stop?
A few day ago, one of the file ws missing. Do you have it all?
Click to expand...
Click to collapse
i did all the steps, all of them work, when the program finished downloading/instaling things on my phone it turned on my phone and it was tuck at the 1+ logo again. when i held the power button+volume down it went to the custom recovery that was installed from the program from the guide. that recovery cant do anything i tried to install a new ROM even the twrp but it always says it failed.
i thought the guide was suposed to install a operating system too but it didnt. now i only have the OnePlus recovery (from the guide) and nothing else. When i try to just turn on the phone (just the power button) its stuck in the 1+ logo. power button+volume up gets the 1+ logo and "fastboot mode" below it
the original recovery tool link doesent work so i downloaded the mini version he posted in the comments, this one ==> https://www.androidfilehost.com/?fid=24269982087019810
maby the OS didnt come with it???
PlsHelpMeee said:
i did all the steps, all of them work, when the program finished downloading/instaling things on my phone it turned on my phone and it was tuck at the 1+ logo again. when i held the power button+volume down it went to the custom recovery that was installed from the program from the guide. that recovery cant do anything i tried to install a new ROM even the twrp but it always says it failed.
i thought the guide was suposed to install a operating system too but it didnt. now i only have the OnePlus recovery (from the guide) and nothing else. When i try to just turn on the phone (just the power button) its stuck in the 1+ logo. power button+volume up gets the 1+ logo and "fastboot mode" below it
the original recovery tool link doesent work so i downloaded the mini version he posted in the comments, this one ==> https://www.androidfilehost.com/?fid=24269982087019810
maby the OS didnt come with it???
Click to expand...
Click to collapse
You have to use the other. This mini tool is from dec 2015.
At last you should have OnePlus recovery + OOS.
Can you retry on an older computer (easier on win 7).
See if it works. At the end, try to fahs the OOS 3.1.4 zip from here :
http://downloads.oneplus.net/oneplus-x/oneplus_x_oxygenos_3.1.4/
Kéno40 said:
You have to use the other. This mini tool is from dec 2015.
At last you should have OnePlus recovery + OOS.
Can you retry on an older computer (easier on win 7).
See if it works. At the end, try to fahs the OOS 3.1.4 zip from here :
http://downloads.oneplus.net/oneplus-x/oneplus_x_oxygenos_3.1.4/
Click to expand...
Click to collapse
I downloaded the oxygen OS form the link, i managed to install it with the 1+ recovery. Everything is working now, thank you for everything!!
Cool if you have done it !
Now unlock bootloader, flash new TWRP and you're good to go to flash all recents customs roms.
My top 3 : Candy 7 // Sultan's LOS // OmniROM
PlsHelpMeee said:
I downloaded the oxygen OS form the link, i managed to install it with the 1+ recovery. Everything is working now, thank you for everything!!
Click to expand...
Click to collapse
Hi, thank you for the information, you made my day! I confirm only the official rom can be flashed. Then I could unlock oem / bootloader and install lineageos on my oneplus x.
Related
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script to get into fastboot at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
So you solve it! :good:
:/
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
foreverman said:
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
Click to expand...
Click to collapse
Then try enter in lelus fastboot mode, ad then flash x-loader, uloader, boot.img and recovery.img from stock rom for your device type model. Then repeat steps 1 and 2
Where can I find the lelus script?
Sent from my Note II
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Then you need a Technician with a Octopus Box to repair your partition table...
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Can you boot into recovery? We now have a custom recovery for locked bootloaders (and CM roms). If you can get into recovery, I would try some adb commands to mount the partitions.
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
ciccillover said:
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
Click to expand...
Click to collapse
Your EMMC partition is wiped or fried... you really need a JTAG service or a Box like octopus because your L9 is Hard-bricked...
Thanks for your opinion. Yet, I still want to hear from others.
I'm running into more and more problems with the L9 as their me grows.
-Fastboot doesn't work under Windows 8.1 and 10, but under the now obsolete(for me) Windows 7, unlike my other devices, which are fine with Win 10.
-ADB seems to work, but requiring the device to be still able to boot.
-I always boot to recovery from within Android as long as the L9 ain't bricked. After a failed rom install, during which the sd card failed(could no longer write or be formatted afterwards, the last time stamps of files and folders were set during the failed install) I discovered a problem with TWRP(Artas182x's and Edwin's), which may have been present since a long time: Trying to invoke TWRP via keypress will brick the device!
So, if my P760 no longer boots, there's only download mode available, sort of the final line of defense.
-There's sort of a trick if even download mode fails: After a failed attempt unplug phone, force switch-off, if the phone is in brick state. Then switch on, force switch-off again, and only then attempt download mode again. And have patience while holding down the vol button, it might take up to 20 seconds for the phone to switch itself on into download mode. (A single forced powerdown will cause Fastboot NOT to work the next time)
But I'm absolutely clueless about the recovery issue, for now TWRP is semi-working, can only be accessed via Android, as long as the phone is fully working.
W/o Fastboot, I now have flashed stock rom several times and rooted it with Kingo rooter just to be able to run Flashify to install TWRP. If Flashify is the culprit for the TWRP issues, I could need a recommendation for a better working app.
ciccillover said:
Thanks for your opinion. Yet, I still want to hear from others.
Click to expand...
Click to collapse
Tried OMAP flasher ? It needs memory configuration file in order to work with our device
No, I didn't. I have sold the phone for spares.
Inviato dal mio LG-D855 utilizzando Tapatalk
I never needed the OMAP drivers and tools. As they are ancient, they will probably make even more problems with newer Windows versions.
I could by no means invoke Fastboot on this device with Windows 8.1 and 10, Seven worked. So you had to go for Download Mode instead to recover to stock rom, then root with the Kingo tool, then install TWRP via Rashr or Flashify, the most time consuming way to recover from the frequent bricks.
And the LG Flash Tool 2014 always needed several attempts to get the job done. The latest official recovery tool from LG works in D/L Mode, but will always download the rom image anew.
First of all I would thank Crowds he is the best reference that I've to return in case of any problem I face. (He doesn't sleep - any time I ask he immediately supports)
I bought Lenovo K910 and I've managed successfully to install new ROM "VIBEUI_v2.0_1443" and Gapps with Crowds support.
I advised two of my friends to buy this good and cheap phone. For one of them I installed the latest rom successfully. But with the other I had a big problem The phone stuck on Lenovo Logo.
I was trying to install TWRP 2.7.0.0 batch before installing my new ROM, but during installation and after the phone rebooting the batch command screen shows <Waiting for Device> and the phone is stuck on logo screen.
I tried to connect the phone to PC many times, but PC doesn't recognize the phone. When I try to turn off the phone by pressing the power buttons, the phone restart on logo screen like the shown in this video.
I've read in many site that I have to do the following:
Download and install "minimal adb and fastboot"
Just type on the command line without pressing Enter:
Code:
[COLOR="Blue"][B][I]fastboot [COLOR="Plum"][STRIKE]boot[/STRIKE][/COLOR] recovery.img[/I][/B][/COLOR]
you should place your recovery image file in "minimal adb and fastboot" directory
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds - in my case the phone is restarting)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery command line
Click to expand...
Click to collapse
In my case when I press and hold power button the phone is restarting on logo screen so I have to wait for battery consumption
I tried many times with TWRP images but it failed...
I tried with CWM image and it succeeded to load, but I don't have otg cable to load recovery or ROM from usb storage (The problem was in installing TWRP and my ROM should has no problem)
I want to flash TWRP on phone not only loading by "minimal adb and fastboot".
I decided to flash TWRP 2.7.1.2 batch through modifying the batch file. I just used fastboot commands
Code:
[COLOR="blue"][I]fastboot oem device-info
fastboot oem unlock
fastboot oem device-info
fastboot [COLOR="Red"][U][B]flash[/B][/U][/COLOR] recovery data/recovery.img
fastboot flash aboot data/lock/emmc_appsboot.mbn
fastboot flash rpm data/lock/rpm.mbn
fastboot flash sbl1 data/lock/sbl1.mbn
fastboot flash dbi data/lock/sdi.mbn
fastboot flash tz data/lock/tz.mbn
fastboot reboot[/I][/COLOR]
Finally I succeeded to install Recovery and phone works well in the new recovery mode and the system mode that I've not update it yet
I want to share you the problem solution in brief:
Download and extract this file "flashrec TWRP v2.7.1.2" from here
Just select without executing "flashrec_Modified.bat" file from the extracted files.
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds or wait for the battery to be almost empty)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery batch file
and as me the phone start the recovery mode in TWRP and can be rebooted in system without any problem
i must extract "flashrec TWRP v2.7.1.2 this file on phone or where? can u explain a
agsao said:
First of all I would thank Crowds he is the best reference that I've to return in case of any problem I face. (He doesn't sleep - any time I ask he immediately supports)
I bought Lenovo K910 and I've managed successfully to install new ROM "VIBEUI_v2.0_1443" and Gapps with Crowds support.
I advised two of my friends to buy this good and cheap phone. For one of them I installed the latest rom successfully. But with the other I had a big problem The phone stuck on Lenovo Logo.
I was trying to install TWRP 2.7.0.0 batch before installing my new ROM, but during installation and after the phone rebooting the batch command screen shows <Waiting for Device> and the phone is stuck on logo screen.
I tried to connect the phone to PC many times, but PC doesn't recognize the phone. When I try to turn off the phone by pressing the power buttons, the phone restart on logo screen like the shown in this video.
I've read in many site that I have to do the following:
In my case when I press and hold power button the phone is restarting on logo screen so I have to wait for battery consumption
I tried many times with TWRP images but it failed...
I tried with CWM image and it succeeded to load, but I don't have otg cable to load recovery or ROM from usb storage (The problem was in installing TWRP and my ROM should has no problem)
I want to flash TWRP on phone not only loading by "minimal adb and fastboot".
I decided to flash TWRP 2.7.1.2 batch through modifying the batch file. I just used fastboot commands
Code:
[COLOR="blue"][I]fastboot oem device-info
fastboot oem unlock
fastboot oem device-info
fastboot [COLOR="Red"][U][B]flash[/B][/U][/COLOR] recovery data/recovery.img
fastboot flash aboot data/lock/emmc_appsboot.mbn
fastboot flash rpm data/lock/rpm.mbn
fastboot flash sbl1 data/lock/sbl1.mbn
fastboot flash dbi data/lock/sdi.mbn
fastboot flash tz data/lock/tz.mbn
fastboot reboot[/I][/COLOR]
Finally I succeeded to install Recovery and phone works well in the new recovery mode and the system mode that I've not update it yet
I want to share you the problem solution in brief:
Download and extract this file "flashrec TWRP v2.7.1.2" from here
Just select without executing "flashrec_Modified.bat" file from the extracted files.
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds or wait for the battery to be almost empty)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery batch file
and as me the phone start the recovery mode in TWRP and can be rebooted in system without any problem
Click to expand...
Click to collapse
Please explain me. idont know how to do
prxzero said:
Please explain me. idont know how to do
Click to expand...
Click to collapse
What Is your problem?
Is your phone stuck on logo screen? what were you doing to get the problem??
agsao said:
First of all I would thank Crowds he is the best reference that I've to return in case of any problem I face. (He doesn't sleep - any time I ask he immediately supports)
I bought Lenovo K910 and I've managed successfully to install new ROM "VIBEUI_v2.0_1443" and Gapps with Crowds support.
I advised two of my friends to buy this good and cheap phone. For one of them I installed the latest rom successfully. But with the other I had a big problem The phone stuck on Lenovo Logo.
I was trying to install TWRP 2.7.0.0 batch before installing my new ROM, but during installation and after the phone rebooting the batch command screen shows <Waiting for Device> and the phone is stuck on logo screen.
I tried to connect the phone to PC many times, but PC doesn't recognize the phone. When I try to turn off the phone by pressing the power buttons, the phone restart on logo screen like the shown in this video.
I've read in many site that I have to do the following:
In my case when I press and hold power button the phone is restarting on logo screen so I have to wait for battery consumption
I tried many times with TWRP images but it failed...
I tried with CWM image and it succeeded to load, but I don't have otg cable to load recovery or ROM from usb storage (The problem was in installing TWRP and my ROM should has no problem)
I want to flash TWRP on phone not only loading by "minimal adb and fastboot".
I decided to flash TWRP 2.7.1.2 batch through modifying the batch file. I just used fastboot commands
Code:
[COLOR="blue"][I]fastboot oem device-info
fastboot oem unlock
fastboot oem device-info
fastboot [COLOR="Red"][U][B]flash[/B][/U][/COLOR] recovery data/recovery.img
fastboot flash aboot data/lock/emmc_appsboot.mbn
fastboot flash rpm data/lock/rpm.mbn
fastboot flash sbl1 data/lock/sbl1.mbn
fastboot flash dbi data/lock/sdi.mbn
fastboot flash tz data/lock/tz.mbn
fastboot reboot[/I][/COLOR]
Finally I succeeded to install Recovery and phone works well in the new recovery mode and the system mode that I've not update it yet
I want to share you the problem solution in brief:
Download and extract this file "flashrec TWRP v2.7.1.2" from here
Just select without executing "flashrec_Modified.bat" file from the extracted files.
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds or wait for the battery to be almost empty)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery batch file
and as me the phone start the recovery mode in TWRP and can be rebooted in system without any problem
Click to expand...
Click to collapse
Hi..
i just try to install CM12 to this device, with twrp 2.8.6.1 from master lie.
First time its working well, but suddenly this device restarting and stuck on the "lenovo" logo screen.
Every time i presh power button always restarting (like ON-OFF-ON-OFF forever).
when i connectto charger also restarting....
i cant go to twrp using vol- & pwr, when i use minimal adb cannot detected..
Can you help me...
Help
hi.
i try to do something to enable notifications on my lenovo vibe z.
i install new rom from needrom, but it didn't help. So i try to install other one, but i wipe my phone and restart without installed system.
Now when i go to twrp have just flashing teamwin logo, and only when phone is in this mode i can communicate through adb
i have checked many forums and try allot stuff to fix it but nothing works
Please Help!
U are not alone I also in same stage
Is there any one plz help
As long as the hardware is not physically broken, your K910 is unbrickable
http://www.teamsuperluminal.org/unbrick-lenovo-k910/
I followed the guide to revive my K910. You can refer to this forum post in which I documented my experiences:
http://www.teamsuperluminal.org/forums/topic/flash-back-to-lenovo-stock-just-temporarily/
nowbo said:
Is there any one plz help
Click to expand...
Click to collapse
Thanks for your reply
I will apply today. Hope for the best.
Will inform you as soon as this applied..
Have you fixed that problem?
Still at same stage
EcoDan said:
Have you fixed that problem?
Click to expand...
Click to collapse
Hi,
I am still on same stage (Black screen with lenovo logo). Try several ways but can't get out of this. Please help me If any one successful to startup this device or can get on the boot screen where I can do factory reset.
---------- Post added at 07:25 AM ---------- Previous post was at 07:21 AM ----------
wxppro said:
http://www.teamsuperluminal.org/unbrick-lenovo-k910/
I followed the guide to revive my K910. You can refer to this forum post in which I documented my experiences:
http://www.teamsuperluminal.org/forums/topic/flash-back-to-lenovo-stock-just-temporarily/
Click to expand...
Click to collapse
I Try this method but can't get out from that black screen ( Lenovo logo and powered by android)
My device is Lenovo Vibe shot Z90a40. I also try with boot unlock-er but nothing sitll work. So its about 20 days can't use my Lenovo Vibe Shot.
Please help me If you know how to get out of this issue..
Thanks
[/COLOR]
I Try this method but can't get out from that black screen ( Lenovo logo and powered by android)
My device is Lenovo Vibe shot Z90a40. I also try with boot unlock-er but nothing sitll work. So its about 20 days can't use my Lenovo Vibe Shot.
Please help me If you know how to get out of this issue..
Thanks[/QUOTE]
You need to carefully follow each steps in the method - if you short that magic pin and then connect the USB cable (with battery disconnected), your computer will report seeing the device at either COM port 9008 or 9006. Then you can download the factory image to revive the phone. Of course you need to have the right device driver installed. Like I said, as long as the hardware is not broken, this procedure will succeed for sure.
I love you man!
I love you man! I wish you all the happiness and wealth!:victory::victory::victory::angel::angel::highfive::highfive:
hey there!
i need some help here please!
i was trying to unlock my bootloader (using this guide) and it went all fine till step 17 (command "fastboot oem unlock-go"), it said i got no permission for unlocking. and now i'm stuck here. the only thing that works is fastboot mode. from there i can switch to adb using the reboot-to-edl-patch, but then i'm stuck again. device-manager shows device as usual (ports COM & LPT) and the red light is blinking, but command "adb devices" replies an empty list. tried "adb kill-server", replugging phone, rebooting computer, still the same.
so what can i do now?
thanks for helping!
Hi. You can install a fastboot rom in edl-mode with mi flash. I recomend a developer rom for this action. Then you can try the unofficial unlock from the start, but i recomend the official unlock.
Odatosz said:
Hi. You can install a fastboot rom in edl-mode with mi flash. I recomend a developer rom for this action. Then you can try the unofficial unlock from the start, but i recomend the official unlock.
Click to expand...
Click to collapse
sorry, forgot to say that miflash does not show the device after i selected the rom. i need to do something before i can flash via edl-mode. but what?
Make sure that you have the correct drivers installed on a 64bit machine, with driver signature off. And you cant get adb device list from there, so thats normal. Try to install the 7.1.8 fastboot rom that should work.
Well even m in a same situation.... as u said ur mobile is giving u red led blinks.. ..
And in device Manger ur fone is showed as Qualcomm 900E instead of 9008 and that's the reason adb couldn't list ur device
All u need to do is do a Google search - xiaomi deep flash cable
shetty_chadda said:
Well even m in a same situation.... as u said ur mobile is giving u red led blinks.. ..
And in device Manger ur fone is showed as Qualcomm 900E instead of 9008 and that's the reason adb couldn't list ur device
All u need to do is do a Google search - xiaomi deep flash cable
Click to expand...
Click to collapse
phone is showed as showed as Qualcomm 9008, and meanwhile i'm able to flash fastboot-rom again. still can't unlock though
AnF replies: FAILED: <remote: oem unlock is not allowed>
finished. total time: 0.016s
drivers are installed correctly, i'm working in signature-off-mode.
tried 7.1.8 rom, can't unlock that either..
maybe a stupid question, but anyway: phone had miui version 8 before i started trying to unlock.. is something wrong with that?
thanks for helping!
no1dev said:
phone is showed as showed as Qualcomm 9008, and meanwhile i'm able to flash fastboot-rom again. still can't unlock though
AnF replies: FAILED: <remote: oem unlock is not allowed>
finished. total time: 0.016s
drivers are installed correctly, i'm working in signature-off-mode.
tried 7.1.8 rom, can't unlock that either..
maybe a stupid question, but anyway: phone had miui version 8 before i started trying to unlock.. is something wrong with that?
thanks for helping!
Click to expand...
Click to collapse
There is no problem with miui 8. You just have to follow the steps from this post: [Tips and Tutorials] Redmi Note 3 [ SnapDragon ] - Unlock the BEAST in Seconds!!! . Just google it, because i cant post links here... Make a efs partition backup before you proceed! With a bad flash you can lose your IMEI like lots on the forum did... I would say to unlock your phone with the official unlock. Good luck!
no1dev said:
phone is showed as showed as Qualcomm 9008, and meanwhile i'm able to flash fastboot-rom again. still can't unlock though
AnF replies: FAILED: <remote: oem unlock is not allowed>
finished. total time: 0.016s
drivers are installed correctly, i'm working in signature-off-mode.
tried 7.1.8 rom, can't unlock that either..
maybe a stupid question, but anyway: phone had miui version 8 before i started trying to unlock.. is something wrong with that?
thanks for helping!
Click to expand...
Click to collapse
Odatosz said:
There is no problem with miui 8. You just have to follow the steps from this post: [Tips and Tutorials] Redmi Note 3 [ SnapDragon ] - Unlock the BEAST in Seconds!!! . Just google it, because i cant post links here...
Click to expand...
Click to collapse
en.miui.com/thread-253680-1-1.html
abihary said:
en.miui.com/thread-253680-1-1.html
Click to expand...
Click to collapse
There you go. Don't forget to read my edit from the other post!
Odatosz said:
There you go. Don't forget to read my edit from the other post!
Click to expand...
Click to collapse
tried that, but no success in unlocking. same reply as mentoined above (FAILED: <remote: oem unlock is not allowed>)
is there any other rom i could try to flash? not to unlock the bootloader afterwards, but to just unbrick my phone?
I would recomend to install a global developer rom for now. And unlock your bootloader with the official method.
---------- Post added at 07:13 PM ---------- Previous post was at 07:09 PM ----------
Just install a developer ROM like you did before. Then you can decide what to do next. I would recommend to unlock your bootloader officially if you want custom ROMs on your phone.
good news: i finally managed to unbrick it!
flashing the fastboot 7.1.8 rom, and then flashing the original emmc_appsboot.mbn file via fastboot:
fastboot flash aboot emmc_appsboot.mbn
fastboot flash abootbak emmc_appsboot.mbn
fastboot reboot
during reboot holding volume-up + power and starting mi pc suite
..and suddenly it's unbricked!
so happy right now!
Glad to hear that.
no1dev said:
hey there!
i need some help here please!
i was trying to unlock my bootloader (using this guide) and it went all fine till step 17 (command "fastboot oem unlock-go"), it said i got no permission for unlocking. and now i'm stuck here. the only thing that works is fastboot mode. from there i can switch to adb using the reboot-to-edl-patch, but then i'm stuck again. device-manager shows device as usual (ports COM & LPT) and the red light is blinking, but command "adb devices" replies an empty list. tried "adb kill-server", replugging phone, rebooting computer, still the same.
so what can i do now?
thanks for helping!
Click to expand...
Click to collapse
The solution is here:
download the required files from the given link: [50mb]
https://mega.nz/#!1NhDTQoR!cP7vrchwswOfj3oHQ5saZ2d0JkcmunEn5pqyOcpZDoE
INSTRUCTIONS: [redmi note 3]
1. Get into fastboot mode. Charge the phone first. Hold the power button and the volume down button simultaenously.
2. If you can open your current rom, open developer options by clicking on the build no several times in the about phone menu in settings. and select allow oem unlocking and usb debugging.
3. if not leave it... go on and connect your phone to the PC while in fastboot mode.
BUT, before that: open Command prompt on your PC. (search it on the search box). right click on it and open it in administrator mode.
type in: bcdedit /set testsigning on
hit enter and restart your pc
(this is imp.)
4. open the zip file and extract the contents. open the boot edl mode folder and click the edl.bat file. allow it to run.
5. now screen will turn black, do not disturb it. Now flash the twrp by running flash twrp.bat from the 'flash TWRP' folder.
6. Now go to Unlock folder and run the unlock bootloader.bat file.
your phone will boot into the TWRP recovery mode automatically.
if it opens in chineese you select every tab and find the globe icon.
if the globe icon is found on any of the tab select it and change the language to ENGLISH.
wipe your system from the wipe tab:
Now download the latest CM13 SNAPSHOT BUILD ROM FOR YOUR REDMI:
https://download.cyanogenmod.org/get/kenzo-snapshot.zip
and GAPPS:
http://opengapps.org/?api=6.0&variant=mini
do select the arm 64 version and mini one.
download from your pc and copy it to micro sd card. enter this card into you phone and go to mount in twrp.
mount the micro sd card storage.
select the zip file on the micro sd card from the install tab on twrp and flash it.
now go back and flash open gapps zip file.
now REBOOT to system. everything will work fine....
Yesterday I tried to flash a a new rom on my Xperia Z2 (unlocked bootloader).
From TWRP I did an advanced wipe and selected basically everything except my mircoSD (because it has the new files).
After a long time of waiting I tried to flash the ZIP file and it gave me an error. I thought this had to do with the wipe so I decided to reboot my phone.
As you can imagine, it got stuck on the Sony logo (because system would be empty).
From this moment I couldn't do anything with my phone, except from the tool Emma.
I now have some clean installation of Sony their Android 6.0.1 for the Z2 (23.5.A.0.570) but Im unable to flash TWRP through fastboot.
The command adb devices shows my phone, fastboot devices gives an empty response.
When I restart to the bootloader from adb and try to flash TWRP I get the message "< waiting for device >".
I tried on three different PCs including a clean install of Windows with all kind of different drivers, yet I cant get fastboot to work.
Am I stuck with this unrooted version of Android now or do you guys have any suggestions for me?
Thanks in advance!
Install drivers correctly
EugenStanis said:
Install drivers correctly
Click to expand...
Click to collapse
As I said I've tried all kind of different drivers (Android tools, Sony drivers and flahstool drivers). So for me it's hard to tell what I'm doing wrong.
My computer notices the phone (if I hold volume up and attach the charger), it just doesn't show up under fastboot devices.
EugenStanis said:
Install drivers correctly
Click to expand...
Click to collapse
Okay, apparently it was because of the driver signature stuff in Windows 10.. The fastboot command now works fine!
Next problem occurred though, flashed the newest TWRP recovery but as soon as I enter "adb reboot recovery" my phone just normally boots again..
Why do things never work out the right way for me as they are intended..
PaulusE said:
Okay, apparently it was because of the driver signature stuff in Windows 10.. The fastboot command now works fine!
Next problem occurred though, flashed the newest TWRP recovery but as soon as I enter "adb reboot recovery" my phone just normally boots again..
Why do things never work out the right way for me as they are intended..
Click to expand...
Click to collapse
Manually boot into recovery by booting up your device normally and when you see a violet LED, press vol+.
Greetings…
W̶i̶l̶l̶ ̶d̶o̶n̶a̶t̶e̶ ̶2̶0̶ ̶U̶S̶D̶ ̶t̶o̶ ̶w̶h̶o̶e̶v̶e̶r̶ ̶c̶a̶n̶ ̶f̶i̶x̶ ̶m̶y̶ ̶p̶h̶o̶n̶e̶ Fixed and contacted both Bordo_Bereli51 and Ante0.
My Huawei Mate 10 got in a bootloop after installing Xposed Framework
It was on Android Oreo 8.0 rooted and bootloader unlocked
Lock state info:
FB LockState: LOCKED
USER LockState: UNLOCKED
Leaving the device to boot normally: HUAWEI logo then reboots.
Vol up+power: eRecovery mode … doesn’t work (wiped data and cache .. tried to download firmware through wifi .. nothing works). ... then tried this method it worked while downloading the firmware .. but after verifying the firmware then installing it when it gets from 0% to 1% it fails and a red exclamation mark appears. :crying:
Vol down + power: fastboot: always get: FAILED (remote: Command not allowed) ). even though the bootloader is supposed to be unlocked. :crying:
Vol up and down: download mode .. on USB: stuck at 5% … without USB connection to computer: nothing happens (a red exclamation mark appears).
The device has an SD card slot: I tried placing the UPDATE.APP in dload folder and pressed both volume buttons but nothing appeared .. did I do something incorrectly?
Here are more info:
product-model: ALP-L29
vendorcountry: hw/meafnaf
build-number: System 8.0.0.38(0310)
fastboot getvar rescue_enter_recovery
getvar:rescue_enter_recovery FAILED (remote: FAIL:need all image flashed!)
fastboot oem oeminforead-SYSTEM_VERSION
...
(bootloader) :ALP-L29 8.0.0.128(C185)
Please help.
thanks in advance
====================
FIXED: Thanks to Bordo_Bereli51 who wrote this post and thanks for Ante0 for recommending DC Pheonix and for taking a lot of his time explaining a lot of things to me privately. contacted both as promised.
How I fixed it (credits to Bordo_Bereli51 for the guide .. I only modified it a bit and added some info from my experience):
1- I purchased a 19 euro -3 days pass for DC Pheonix.
2- Download Firmware Finder and click the "Common Base" tab, then download a FullOTA-MF firmware (all 3 files) which is approved for installation ( I copied the "changelog" link and pasted it in the 6th icon at the top "Firmware Checker" and it returned "Firmware approved for install" I' was not able to repack other non approved firmwares).
3- extract UPDATE.APP from update.zip
4- run DC Phoenix program .. tap the "Standard" button in Update mode .. select "update" and choose the UPDATE.APP you just extracted.
5- let it flash everything successfully then redo step 4 again.
6- Here's the trick before it flashes anything ... as soon as you see "utilizing backdoor" (or something like that) open Task Manager and force close DC Phoenix (it has to be BEFORE flashing anything, otherwise you might get errors like:
"error: exec '/system/bin/sh' failed: No such file or directory"
and AFTER utilizing backdoor (so you can use fastboot commands)
7-Download HWOTA8_Mate10 , place the 3 files you downloaded in step 2 in the "repack" folder, and rename "update_data_full_public.zip" to "update_data_public.zip" and "update_full_*ALP-L29*_hw_*meafnaf*.zip" to "update_all_hw.zip". Then run "repack.bat" and wait for it to finish.
8- run "ota.bat" in "ota" folder.
9- When it flashes the recovery_ramdisk and kernel plug your usb cable out and Reboot to recovery by pressing volume up + power button
10- When the phone is in recovery now ADB works (in case you need to do things manually).
11- When this process also finishes, the command center will tell you to press enter, so it boots to erecovery, which will flash the files.
12- Now your phone is unbricked after the flash.
Do not forget to do factory reset by pressing again at boot: (power + volume up) and selecting (factory reset).
After boot allow (OEM Unlock) under (developer settings) or otherwise the FRP will still be locked but the phone will work.
if someone will fix it can u tell me cause i have the same problem
---------- Post added at 06:58 AM ---------- Previous post was at 06:58 AM ----------
wait do u have twrp?
Dolev234786 said:
if someone will fix it can u tell me cause i have the same problem
---------- Post added at 06:58 AM ---------- Previous post was at 06:58 AM ----------
wait do u have twrp?
Click to expand...
Click to collapse
I have the same problem.
Dolev234786 said:
if someone will fix it can u tell me cause i have the same problem
---------- Post added at 06:58 AM ---------- Previous post was at 06:58 AM ----------
wait do u have twrp?
Click to expand...
Click to collapse
No, I don’t have TWRP.
hero3210 said:
No, I don’t have TWRP.
Click to expand...
Click to collapse
What does fastboot mode say, unlocked on both phone and frp?
ante0 said:
What does fastboot mode say, unlocked on both phone and frp?
Click to expand...
Click to collapse
yes both are unlocked
Dolev234786 said:
yes both are unlocked
Click to expand...
Click to collapse
Post input & output when you try to flash using fastboot
ante0 said:
Post input & output when you try to flash using fastboot
Click to expand...
Click to collapse
My device used to be bootloader unlocked
But I always get "FAILED (remote: Command not allowed)" for any fastboot command
I searched here and a lot of people had the same issue and they fixed it by relocking then re-unlocking the bootloader
I tried that .. relocked successfully but now I cannot unlock it again.
This is the current info from info.bat:
Lock state info:
FB LockState: LOCKED
USER LockState: RELOCKED
in fastboot mode it says:
PHONE Relocked
FRP Lock
=====
Input and output of fastboot:
fastboot flash recovery_ramdisk SYSTEM.img
target reported max download size of 471859200 bytes
sending sparse 'recovery_ramdisk' 1/7 (460797 KB)...
OKAY [ 3.650s]
writing 'recovery_ramdisk' 1/7...
FAILED (remote: Command not allowed)
finished. total time: 3.661s
Thanks for taking time to reply
hero3210 said:
My device used to be bootloader unlocked
But I always get "FAILED (remote: Command not allowed)" for any fastboot command
I searched here and a lot of people had the same issue and they fixed it by relocking then re-unlocking the bootloader
I tried that .. relocked successfully but now I cannot unlock it again.
This is the current info from info.bat:
Lock state info:
FB LockState: LOCKED
USER LockState: RELOCKED
in fastboot mode it says:
PHONE Relocked
FRP Lock
=====
Input and output of fastboot:
fastboot flash recovery_ramdisk SYSTEM.img
target reported max download size of 471859200 bytes
sending sparse 'recovery_ramdisk' 1/7 (460797 KB)...
OKAY [ 3.650s]
writing 'recovery_ramdisk' 1/7...
FAILED (remote: Command not allowed)
finished. total time: 3.661s
Thanks for taking time to reply
Click to expand...
Click to collapse
You need to enable OEM unlock in Settings-developer options. At least frp needs to say unlock else you won't be able to unlock or flash, at least not for free.
But since you can't boot you're pretty much limited to use dc unlocker/dc phoenix
ante0 said:
You need to enable OEM unlock in Settings-developer options. At least frp needs to say unlock else you won't be able to unlock or flash, at least not for free.
But since you can't boot you're pretty much limited to use dc unlocker/dc phoenix
Click to expand...
Click to collapse
Thanks for the reply
Do you recommend that I use dc unlocker or dc pheonix or FunkyHuawei?
do you recommend that I use dc unlocker or dc pheonix or FunkyHuawei?
hero3210 said:
Thanks for the reply
Do you recommend that I use dc unlocker or dc pheonix or FunkyHuawei?
Click to expand...
Click to collapse
Dc phoenix is what you'll need, Mate 10 is not supported in DC Unlocker. (Though DC Unlocker made DC Phoenix)
You'd just want it to flash stock anyway.
And it's cheaper than FunkyHuawei... FH "only" cost 1 credit to flash, but minimum to buy is 5 credits which is $41.
FH is easier though as you'd only need to setup DNS, but it's up to you
HCU/DC Phoenix pass for 3 days is €19, and then you have unlimited usage.
If you need further help you can find me at the telegram group https://t.me/HuaweiMate
as it's easier to do it live than through messages.
There is a "DC Phoenix repair tutorial" if you google it, use Method 1. Basically you just download the firmware update zip you're on now (and hw data zip) from http://pro-teammt.ru/firmware-database/ then extract update.app from it and select it in Phoenix, then extract update.app from hw data zip and select it as customization.
Alternatively you can downgrade to factory build using images from DC Phoenix (the build your phone came with) then update from there when you have a booting phone.
Thank you sooo much man. I really appreciate your help.
What version of Xposed frameworks did you install I have beta 4 working fine on my mate 10 pro.
tokoam said:
What version of Xposed frameworks did you install I have beta 4 working fine on my mate 10 pro.
Click to expand...
Click to collapse
yeah the bootloop was fixed in beta4 (original comment by dev) which wasn't officially released to the channel when I installed it, so I didn't know about it until I got the bootloop.
Anyways, I just managed to fix my issue. I'll post about it now.
ante0 said:
What does fastboot mode say, unlocked on both phone and frp?
Click to expand...
Click to collapse
what would happens if it says unlock on frp? i cant load twrp i have flashed many times but i does not take it.
I bricked my Huawei Mate 10 too
Please help.. I also bricked my Huawei Mate 10 ALP-L29C636...
I installed the EMUI 9.0 on my device using the HWOTA8_Mate10 method which was successful. The EMUI 9.0 ROM was from FirmwareFinder: ROM version ALP-L29C636E2R1P8B108-log (9.0.0.108). I didn't have any issues at all but since Huawei Mate 10's EMUI 9.0 is still in Beta, I decided to switch back to the stable EMUI 8.0.
Here's where the problem started... Since I want to downgrade, I went ahead and downloaded the 3 needed files (update.zip, update_all_hw, update_data_public) from FirmwareFinder: ROM version ALP-L29C636B143 (8.0.0.143). I fired up HWOTA8_Mate10 and started the installation process. The first step was to boot to fast boot and then plug the device, after that, the software asked me to unplug the device and press volume+ and power button but the device won't boot to recovery anymore. The device is now stuck at "Your device is booting now..." I tried rebooting the device but it won't work. Tried to go to eRevovery to wipe cache/factory reset but it will go back to "Your device is booting now..." page. I tried reinstalling the recovery.img via fastboot and tried to boot to recovery mode again but it won't work anymore. I believe my device is now soft bricked . I can still boot to fastboot, I even tried fastboot flash system system.img which was successful but the device still won't boot. Please help how to recover my device. I think I went too far and now I don't know how to fix this issue.
Carnage! said:
Please help.. I also bricked my Huawei Mate 10 ALP-L29C636...
I installed the EMUI 9.0 on my device using the HWOTA8_Mate10 method which was successful. The EMUI 9.0 ROM was from FirmwareFinder: ROM version ALP-L29C636E2R1P8B108-log (9.0.0.108). I didn't have any issues at all but since Huawei Mate 10's EMUI 9.0 is still in Beta, I decided to switch back to the stable EMUI 8.0.
Here's where the problem started... Since I want to downgrade, I went ahead and downloaded the 3 needed files (update.zip, update_all_hw, update_data_public) from FirmwareFinder: ROM version ALP-L29C636B143 (8.0.0.143). I fired up HWOTA8_Mate10 and started the installation process. The first step was to boot to fast boot and then plug the device, after that, the software asked me to unplug the device and press volume+ and power button but the device won't boot to recovery anymore. The device is now stuck at "Your device is booting now..." I tried rebooting the device but it won't work. Tried to go to eRevovery to wipe cache/factory reset but it will go back to "Your device is booting now..." page. I tried reinstalling the recovery.img via fastboot and tried to boot to recovery mode again but it won't work anymore. I believe my device is now soft bricked . I can still boot to fastboot, I even tried fastboot flash system system.img which was successful but the device still won't boot. Please help how to recover my device. I think I went too far and now I don't know how to fix this issue.
Click to expand...
Click to collapse
Spamming every thread won't help you fix your issue.
Pretoriano80 said:
Spamming every thread won't help you fix your issue.
Click to expand...
Click to collapse
I apologize. I panicked since I don't know what to do. I will continue on the thread which I received a response.