Hi All,
This thread is to add onto the already created thread started by @otonieru, this is not my own work and is mostly due to the aforementioned member. I have also taken tips from that thread from other members, sorry if I don't mention you but if you let me know I'll add your name onto this thread.
Thanks goes to: @otonieru @Blasembauer @Mr. Orange 645
What you'll need
- Tempered Glass Screen Protector (try to get one without the matrix dots)
- Installation Guide - if you have one it makes the process easier, if not it's fine
- LOCA UV Glue (1000mPa should be fine)
- UV Lamp (30W+ if possible)
All in all this cost me under £20, all ordered on Amazon UK.
How do I install the Tempered Glass with LOCA UV Glue?
Video demonstration here:
https://www.youtube.com/watch?v=bwwKim90sS8
1. Clean screen, remove dust particles etc.
2. Tape up all speaker & microphone & charging ports, volume & lock keys. Most importantly securely tape up your earpiece! Otherwise you'll run into some low volume problems during calls. Use thick tape if possible (If you have an installation guide from the tempered glass, apply this on top after taping up the phone).
3. Apply your LOCA Glue onto the screen in this kind of shape [ >----< ] [ ] Being the top and bottom screen and >---< being the glue. From my experience I used 'Xfactor LOCA UV Glue 1000mPa*s' and it worked a treat (Bought from Amazon UK).
4. Working from bottom to top, place the Tempered Glass on, ensuring the glue spreads evenly to the edges. If the glue seeps out from the edges just clean it with tissue, but best to do this once the glue has spread evenly across the screen and no bubbles are present. Push out any remaining area the glue hasn't spread to, and push out and bubbles. Take off installation guide if you've used one now. The Tempered Glass can be freely positioned at this point if it's out of alignment as the glue hasn't set yet.
5. Place under UV lamp for 10-20mins. Be careful not to knock the TGSP. I used a 30W UV Nail Lamp that was big enough to fit the whole phone in and it cured within 10mins.
6. Clean up hardened glue with a brush, hardened UV Glue will take some pressure to scrub off so be patient. Use water or Isopropanol Alcohol to aid in this.
7. Enjoy your Tempered Glass with full adhesive
If you need to reapply follow steps 1-6 again.
I got UV Glue stuck in my earpiece and the volume is ridiculously low
Method A:
Firstly, try brushing your earpiece lightly with a brush, making sure not to push any UV glue further into the earpiece.
Method B:
Failing method A, you will need in addition to that:
- A Can of Compressed Air, the type you use for electronics/ screens etc (can get one from Asda for £3)
- Isopropanol Alcohol
You will need to soak your earpiece with the Alcohol and start brushing the earpiece. After it's been soaked for 2-3mins use your Compressed Air to clear the earpiece; the UV glue should have been softened and removed once the air blows into the earpiece.
Failing both these methods, you've probably wrecked your earpiece....
I've got Air Bubbles after applying the TGSP
Unfortunately you'll have to remove the TGSP and reapply, following all the steps again, make sure to thoroughly clean the screen using the alcohol wipes & dust stickers.
If there's any other problems/ questions that users have, feel free to post and I'll add it to the OP.
Do you have glues to recommend, I've been looking for them on aliexpress(unfortunately is the easiest place for me to order them ) I saw ones but idk about the quality.
https://www.aliexpress.com/item/Free-Shipping-tp-1000-UV-Glue-LOCA-Liquid-Optical-Clear-Adhesive-for-iPhone-Samsung-HTC-Glass/32271580944.html?spm=2114.search0104.3.9.qNtfdA&ws_ab_test=searchweb0_0,searchweb201602_4_10152_10065_10151_10068_10344_10342_10343_10340_10341_10307_10137_10060_10155_10154_10056_10055_10054_5470020_10059_100031_10099_5460020_10338_10339_10103_10102_440_10052_10053_10142_10107_10050_10051_10173_5380020_10326_10084_10083_10080_10082_10081_10110_10111_10112_10113_10114_143_5570011_10312_10313_10314_5560020_10078_10079_10073,searchweb201603_19,ppcSwitch_7&btsid=cd42bca1-82dc-4542-860a-017481d2be5a&algo_expid=0b632118-0504-46ba-b5b6-6c47126ef5bb-1&algo_pvid=0b632118-0504-46ba-b5b6-6c47126ef5bb
It says that is a Genuine glue and is the same from a video on youtube.
Do you think that it should be good?
Blasembauer said:
Do you have glues to recommend, I've been looking for them on aliexpress(unfortunately is the easiest place for me to order them ) I saw ones but idk about the quality.
https://www.aliexpress.com/item/Free-Shipping-tp-1000-UV-Glue-LOCA-Liquid-Optical-Clear-Adhesive-for-iPhone-Samsung-HTC-Glass/32271580944.html?spm=2114.search0104.3.9.qNtfdA&ws_ab_test=searchweb0_0,searchweb201602_4_10152_10065_10151_10068_10344_10342_10343_10340_10341_10307_10137_10060_10155_10154_10056_10055_10054_5470020_10059_100031_10099_5460020_10338_10339_10103_10102_440_10052_10053_10142_10107_10050_10051_10173_5380020_10326_10084_10083_10080_10082_10081_10110_10111_10112_10113_10114_143_5570011_10312_10313_10314_5560020_10078_10079_10073,searchweb201603_19,ppcSwitch_7&btsid=cd42bca1-82dc-4542-860a-017481d2be5a&algo_expid=0b632118-0504-46ba-b5b6-6c47126ef5bb-1&algo_pvid=0b632118-0504-46ba-b5b6-6c47126ef5bb
It says that is a Genuine glue and is the same from a video on youtube.
Do you think that it should be good?
Click to expand...
Click to collapse
Yes that is the same viscosity as the one I used, so it should work okay
If you warm up any of the LOCA glue before you use it, it will become less viscous and flow better I think.
Please, please follow the OP's advice and tape your earpiece. I foolishly trusted someone in the other thread who said the LOCA would not penetrate the earpiece mesh and could just be simply brushed away once dried. WRONG.
I was using a full coverage protector that only had a tiny cutout for the speaker and that was it (still the best looking TGSP available, no dots). I couldn't get the speaker taped and thought, i'll take a chance. It's water proof and LOCA is WAY thicker than water. Well, I manage to get LOCA in my speaker grill, I carefully peeled it off once dried, and brushed it away, but no joy. I could barely hear anything from the speaker. I tried rubbing alcohol and more brushing, but nothing would fix it. I did not think about compressed air, wish I would've now.
In any case, I bit the bullet, disassembled my phone and cleaned out the speaker grill from the inside. Goodbye warranty and IP68. That screen protector was really nice though and the first truly oleophobic TGSP I had found. And with my thin Cafele case, it was invisible. I was pretty happy despite the speaker incident. Until the very next day when I pulled my phone out of my pocket and the TGSP had cracked...on nothing. Just the phone in my pocket, nothing else, but something had hit the edge and cracked it. So it wound up not being worth it.
Now I'm on a quest to find a good full coverage PET/TPU/hybrid screen protector. Thought I found the perfect one in the Dendrobates soft glass. Looks and feels good, but the edges won't stick down no matter what.
Good luck to everyone trying the TGSP and LOCA. It truly is the best way to protect your screen on this phone. I just had bad luck with them cracking too easy (though one did give its life to save my screen), and then when I clogged my speaker, I decided to go another route.
I have such a love-hate relationship with this curved screen. LOL
Do you meet yellowing effect after few days ? Can i use Loca glue 2500mPa instead ? What is difference between 1000 and 2500 ? Thanks.
for the tempered glass, i recommended this. no matrix dot. Hold up pretty well
https://www.amazon.com/gp/product/B072QBYF6L/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
Cloudran said:
Do you meet yellowing effect after few days ? Can i use Loca glue 2500mPa instead ? What is difference between 1000 and 2500 ? Thanks.
Click to expand...
Click to collapse
I believe that is the viscosity of the LOCA glue, the less thick the easier it is to spread evenly. And no I didn't see any yellowing effect.
Mr. Orange 645 said:
Please, please follow the OP's advice and tape your earpiece. I foolishly trusted someone in the other thread who said the LOCA would not penetrate the earpiece mesh and could just be simply brushed away once dried. WRONG.
I was using a full coverage protector that only had a tiny cutout for the speaker and that was it (still the best looking TGSP available, no dots). I couldn't get the speaker taped and thought, i'll take a chance. It's water proof and LOCA is WAY thicker than water. Well, I manage to get LOCA in my speaker grill, I carefully peeled it off once dried, and brushed it away, but no joy. I could barely hear anything from the speaker. I tried rubbing alcohol and more brushing, but nothing would fix it. I did not think about compressed air, wish I would've now.
In any case, I bit the bullet, disassembled my phone and cleaned out the speaker grill from the inside. Goodbye warranty and IP68. That screen protector was really nice though and the first truly oleophobic TGSP I had found. And with my thin Cafele case, it was invisible. I was pretty happy despite the speaker incident. Until the very next day when I pulled my phone out of my pocket and the TGSP had cracked...on nothing. Just the phone in my pocket, nothing else, but something had hit the edge and cracked it. So it wound up not being worth it.
Now I'm on a quest to find a good full coverage PET/TPU/hybrid screen protector. Thought I found the perfect one in the Dendrobates soft glass. Looks and feels good, but the edges won't stick down no matter what.
Good luck to everyone trying the TGSP and LOCA. It truly is the best way to protect your screen on this phone. I just had bad luck with them cracking too easy (though one did give its life to save my screen), and then when I clogged my speaker, I decided to go another route.
I have such a love-hate relationship with this curved screen. LOL
Click to expand...
Click to collapse
Ah man that sucks! If only that problem was brought up quicker, the solution would've saved you from losing your warranty & waterproofing .. I thought I had to go down the same route as you until someone suggested using a can of compressed air! Completely solved my issue.
Yeah....I wasn't happy. Live and learn though.
Then about three weeks later, my wife broke the screen on her S8+. So I'll be replacing her screen and losing her warranty as well.
I just try to keep in mind if that's the worst of my problems, then it's not all that bad.
I just ran into this thread, and it got me curious. I have previously tried the Rhinoshield TGSP, but it didn't fit, and sensitivity was an issue, and now I'm contemplating trying this with LOCA glue.
However, can anyone tell me first, if there are any problems on removal? I'd hate to damage the screen, or have permanent marks from the glue.
ahadzivasilev said:
I just ran into this thread, and it got me curious. I have previously tried the Rhinoshield TGSP, but it didn't fit, and sensitivity was an issue, and now I'm contemplating trying this with LOCA glue.
However, can anyone tell me first, if there are any problems on removal? I'd hate to damage the screen, or have permanent marks from the glue.
Click to expand...
Click to collapse
Nope no damage whatsoever as long as you follow the instructions to tape up the earpiece. LOCA Glue is very easy to remove, once it's set it just turns into a jelly-like substance which peels off easily.
Good day everyone
in case of a glass with this form... how do i can seal the speaker from getting impregnated with LOCA?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
x-geo said:
Good day everyone
in case of a glass with this form... how do i can seal the speaker from getting impregnated with LOCA?
View attachment 4301613
Click to expand...
Click to collapse
Don't use those ones, the Loca under the black parts will not cure properly
Sent from my SM-G950U using Tapatalk
dlinfiniti said:
Don't use those ones, the Loca under the black parts will not cure properly
Sent from my SM-G950U using Tapatalk
Click to expand...
Click to collapse
Thanks for your answer, and yes... i have one without the black parts.. totally trasparent
Anyone know the best way to clean glue from around the side buttons (volume rocker)? I taped up my phone but it managed to leak in because I put too much glue . The buttons work fine but I don't want problems down the road
Im still struggling to find a tempered glass with no dot matrix. I had read KUMHIO brand on Amazon, but im in Canada and that one doesnt seem to be available on Amazon.ca. Also it's reviews on amazon.com say it doesnt have a oelophobic coating
Does anyone know of an other one?
alirz said:
Im still struggling to find a tempered glass with no dot matrix. I had read KUMHIO brand on Amazon, but im in Canada and that one doesnt seem to be available on Amazon.ca. Also it's reviews on amazon.com say it doesnt have a oelophobic coating
Does anyone know of an other one?
Click to expand...
Click to collapse
But which is the problem of dot matrix? Cuz use one and I don't have any problems with bubbles, and I can't even see the dot matrix.
baophucdinh31 said:
for the tempered glass, i recommended this. no matrix dot. Hold up pretty well
https://www.amazon.com/gp/product/B072QBYF6L/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
Click to expand...
Click to collapse
How is it in terms of surface smoothness and clarity? is it comparable to the whitestone dome glass?
janver22 said:
How is it in terms of surface smoothness and clarity? is it comparable to the whitestone dome glass?
Click to expand...
Click to collapse
i never use the white dome ( for obvious reason: price) but i would the kimiho tempered glass is pretty clear, although it doesnt comes with the oleophobic coating. So will spend a lot of time cleaning your screen. If you want to can buy the coating, for buy a screen with that coating
I recommending this. Currently what i'm using right now.
https://www.amazon.com/gp/product/B07675RF1S/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
Related
This installation tips should be applicable to most of the protective films on Tilt 2/TP2.
There are quite a few posts already comparing various protective shields for the TP2. It would be redundant to discussing which one is better.
After reading on most of the threads on this subject, I went ahead and got the GadgetShieldz. I am quite careful with my phones and I have only used screen protectors but never full coverage shield. I figure using the coupon, it only cost $5.59 and it is cheap enough for me to experiment.
http://forum.xda-developers.com/showthread.php?t=605241&highlight=gadgetshieldz
The package arrived quite fast even during the holiday. There were no instructions sent. No problem, I went on line and got the instruction. However, this instruction is only for the installing the screen protector.
http://www.gadgetshieldz.com/Installation.html
The instruction is good and easy to understand. Since I do not have baby soap, I use Neutrogena body soap instead. It worked fine.
Part One
I have the stock screen protector on my Tilt 2 already and I wanted to pick something easy to try before I attempt to do the screen. So I decided to try out the back first. The center strip for the camera is small and flat and it seems to be the easiest to apply. So I started with this piece first. I would recommend to do this piece first as it would give you some idea what it is going to be like when you are doing the bigger pieces.
I removed the battery cover from the phone. As I was a little worry working with water near the phone. I wiped the battery cover with an alcohol swab to remove any grease. Clean it again with a clean cloth.
Remove the film from the backing and dipped into the soapy solution and I applied it with no trouble at all. I removed the excess water and a tiny bubble with a “credit card”. Everything worked as advertised.
So I proceed with the battery cover. Again dipped the protective film in the wetting solution, followed the instructions by removing the excess water with fingers. Applied the film at the center and positioned it. It was not difficult to move the film, as I probably left the film too wet. Once I am satisfied with the position. I squeezed out the water with my “credit card”, removing any air bubbles at the same time. The center part of the battery cover was a piece of cake but the corners are impossible to apply. I simply could not get the corners down correctly. 30 minutes passed and I am still not satisfied with the result. I actually have to re-wet a corner just to get the finger/tabs into the right places. I was also very careful not apply too much pressure because I do not want to stretch the film. I was thinking this is not going to work and I probably wasted my $5.59 and all my time. Then all of a sudden, it seems the corners are going down on the case. After the first corner went down, the rest was easier. I work the corners mostly with my fingers, only used the “credit card” on some of the edges.
I took me an hour to do the battery cover. I probably had too much water on the film.
I grabbed a tissue paper to wipe off any excess water off the edges of the film (Mistake No 1.). The lint off the tissue paper stuck to some of the excess glue residual. While the film is fitting the corners very well, the edges were fuzzy with lint.
I left the cover out to dry. While the lint was not that visible, it still bothered me. So after a couple of hours, I use my 10 X glass to inspect the edges. I was not happy. By then the film is sitting on the cover pretty firm and it did not like it was going to move. I went ahead and use a hair drier to speed up the process. I am glad that I did. The heat improved the appearance of the film and it was not as lumpy as before. I realized what had happened. The film is made of some kind of polymer plastic. Polymer plastic has a tendency to shrink when exposed to heat. The hair drier was shrinking the film and made the film fitting the cover tighter. This is a GOOD thing. If you stretched the film, this applying of heat should correct some if not all of this. Just be very carefully not to apply too much heat or you distorted the film. The edges of the film must not protrude beyond the case as this would cause the film to lift.
I admit that I am picky, the lint at the edges were bugging me. So I use a few wood tooth picks and a bottle of Glue Off. (Citrus adhesive remover) and remove all the excess glue and the lint off the edges. The results were good. There were still a little glue left on some of the edges but this is not noticeable with a naked eye.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Part Two
Installing the protective film on the sides (Chrome Bezel).
I started with the bottom strip first as it is one of the shortest one. I always choose the easiest task to gain experience. There was a notch on the bottom left size. I believe it is cut out for the microphone. Worrying that I might cover the microphone, I lined up the film strip to the top edge of the chrome bezel (Mistake no. 2). I was careful; not placing the strip too far up or it would catch my finger when I push those hardware buttons on the lower edge. The bottom film strip was short and I more of less got it in a good position.
Then I started both side pieces at the same time, wetting the strips (Mistake no.3). I then placed them on the sides trying to line them up against the upper edge and not too far up so they would protrude above the chrome bezel. I just could not get them in the right position. The film strips were long and limpy. They slide and glide along the edges. It was a chore just trying to position one piece. Doing both was impossible. I had to place one at the edge of the bowl that contained my wetting solution (adhesive side up). Working with one piece was still impossible. I just could not place it correctly; the film would not stick until the wetting solution was almost dry up. By the time the film was ready to be glue down, the position was not right again. So off it went and back to the wetting solution bowl.
I was fretting and not in a happy state until I took a look at the "credit card" that was used to remove bubbles and excess water. I made a bad decision when I tried to line up the film strip against the top edge of the bezel. I should have line it up with the bottom of the bezel. It was actually easy if I slide the "credit card" between the screen and keyboard. The lower edge of the film could just be resting on the "credit card" while it was waiting to be dried. When the film was ready, I pressed the middle and worked my way to the edges of the strip. Once the film is secured (not longer moving) on the chrome bezel. I pulled the "credit card" out and used it to remove bubble and excess water.
The opposite long strip went on without any fuss. The last piece on the top got done in a short time also. It took quite some time but most of the time was waiting for the wetting solution to be dried. Before I figured out how to do this, I was trying constantly holding on to the strip correcting its position.
The cut out on the top piece was a bit tight and I did not get it place perfectly. Otherwise, it was on quite well. I ended up using a X-acto knife and knick off a tiny piece to uncover the whole power button.
The top part of the battery cover was a little too short, an additional of 0.8-1.0mm would be about right.
The smudge on the edge is my finger print.
Part Three
I installed the film on the screen last as I was worried about not doing it correctly and ended up with bad gaps and bubbles. Actually this was the easy part. I did have to peel it off twice before I got this correct. I thought I would speed up the process by getting rid of most of the wetting solution on the film before I apply. The film was applied and was sticky very fast. I could not move the film and position it. So I have to peel it off and wet it again. It was the third try before I got it right. I was worried about too much wetting solution getting to the speaker. I should have applied the same amount just like when I did the back. I did have some Q-tips at hand to soak up any wetting solution that was squeezed off the edges. I then applied the hair dryer carefully to speed up the process,
Conclusion
Do not afraid of the wetting solution. Using more will make it easier to position but it’ll take longer to stick. I would avoid removing and reinstalling the film. This would give the adhesive a chance to get lint or dirt stick on it.
Use a smooth card instead of a credit card. Hotel room key card works great. Hotel room key card does not have embossed letters. You can use it to roll over the edges on the film.
Slide a card between the key board and the screen for the Chrome Bezel. Line the film on the bottom edge. Do not let any film protrude above the screen.
Do not place any tissue close to where you are working. I know about the lint issue but still grabbed the tissue just because it was at hand.
Applying heat with a hair dryer is fine and it will cure the film and you can use the phone next morning. Just be very careful not over heating the phone.
I applied this set in 3 evenings. I did one part at a time so I could give as much time as possible for the film to dry.
GadgtShieldsz fits OK. The top piece for the chrome bezel should be longer and wider.
The back piece could be slightly bigger and the gaps on top 2 corners could be narrower.
The screen piece fits great. It does drags very little but I have no problem with it.
Otherwise, this GadgtShieldsz is hard to beat. It is cheap and provides good coverage (protection) all over,
Learn from my mistakes and may your installation comes out better than mine.
Great job, mate! I think you did excellent! Unfortunately, they don't make shield for the unbranded version I have so I had to buy one from bodyguardz which I still wait to receive, but I bought one for my friend's Omnia and is great, came in 3 days also
I still believe it's the best considering the price!
MightyCrys said:
Great job, mate! I think you did excellent! Unfortunately, they don't make shield for the unbranded version I have so I had to buy one from bodyguardz which I still wait to receive, but I bought one for my friend's Omnia and is great, came in 3 days also
I still believe it's the best considering the price!
Click to expand...
Click to collapse
Thanks Bud! I notice that the Bodyguardz has those pieces on the Chrome Bezel. Just remember to slide a card between the keyboard and the screen. This would make the installation much easier and the protective film is straight. If the film is cut right, you do not have to worry about the film protruding above the Bezel. Good luck on your installation and do not forget to post pictures.
Hadn't seen it mentioned here so I thought I'd share. I made a screen protector that fits nicely over the camera glass on the back of the phone. I think that camera glass is pretty tough (in fact, I personally think only the camera glass is Gorilla Glass) but I still feel better with it protected since many cases don't protect that area and it sticks out.
Having gone through several iPhones before making the switch to the Evo 4G last year, I had plenty of extra screen protectors lying around. So I basically just took one (a clear one obviously, not an anti-glare) and cut it to the shape of the camera glass and installed. I've taken multiple pictures to test it and I find no degradation at all in the images. Here are the deets:
(1) Pick a clear protector: one of the kind that has the protector sandwiched between two clear pull-offs labeled "1" and "2". These actually consist of three clear sheets: one protector which is itself protected by two pull-off (disposable) clear sheets.
(2) Normally the white "1" and "2" pull-off stickers are located against one edge (top or bottom) of the protector. Orient the protector so that the "2" pull-off sticker is on the top and "1" is on the bottom. If the edge opposite the stickers has an earpiece hole (ala iPhone), cut straight across inward of the hole so you have one solid piece with no hole. I used a paper cutter to be sure I had cuts that were square but scissors are OK if you are careful.
(3) Turn the phone over so the camera is pointing up. Align the edge of the protector opposite the pull-offs against one of the long edges of the camera glass. Align it such that the protector is on the inside edge of the glass touching the metal ring but flush against the glass. That way you will not have to cut that side. With the "2" sticker still pointing up, write the word "UP" on the protector so that it is about in the middle of the camera glass. You need a reference and you'll peel that top piece off later so it doesn't matter if you write on it.
(4) With a fine point Sharpie or other marker, mark around the three remaining edges. You can see the metal ring under the protector. Just hold the protector as straight as you can and trace around the inside edge of the glass so that the inside edge of your mark aligns very closely with the inside edge of the glass where the glass meets the metal ring. When you're done, it'll look something like this: (___)
(5) Carefully cut on the inside edge of the lines you made to make a shape the same as the glass. Before pulling off any pull-offs, lay the cut piece on the glass to be sure it can lay flat. I had to trim the corners manually a couple times to get just a tiny space between the glass and the metal ring to be sure it would lay flat. When you're done cutting, if you matched inside edge (of the mark) to inside edge (where glass meets metal ring), none of your markings should be visible on the cut piece when you are done. At this point, since you've matched up the size and you won't need to touch the glass any more to align or mess with things, clean the camera glass thoroughly: dust creates bubbles!
(6) On one of the two short edges, attach two strips of narrow scotch/clear tape: one on the top and one on the bottom of the short side. Align them so that the two pieces don't overlap: else they will stick together. So one piece should be against one edge on the top, and the other piece should be against the other edge on the bottom. These are now your new "1" and "2" pull-offs. Why not just use the existing pull-offs? Because it's easier to see, mark, and cut on a "virgin" edge with no pull-offs in the way and also because, when you're done, you still have a good piece of protector film that still has the original pull-offs on it in case you want to make more like this.
(7) With your word "UP" facing up, hold onto the top piece of tape while pulling gently down and inward on the bottom piece to peel off the bottom pull-off sheet. Make sure you are peeling only the bottom layer and not the top two: the bottom layer should be the thinnest when it peels.
(8) Now you should be holding the protector from the top pull-off (your tape) and the bottom part of the protector that contacts the glass is exposed. Be sure not to touch anything at this point but the piece of tape you are holding. While holding onto your top pull off and with the word "UP" facing up, gently lay the protector down onto the camera glass. When it looks aligned, simply drop the side that you are holding (with the tape) down and it should nearly instantly bond with the glass. No need to worry about bubbles or bending at this point due to the size of the protector. If it isn't straight, you should be able to still pull up on the top piece of tape and get the whole thing to pry up (both layers) and realign. If you want to do that, the key to pulling the whole set off together without peeling only one layer is to pull away and out (away from the center of the sheet). When you pull away and in, you'll peel one layer and you'll leave the protector itself on the glass.
(9) With a credit card or small piece of cardboard, work out any bubbles that might be present. Then once the protector has been pressed against the glass firmly, peel slowly up and inward on the top piece of tape. You should be able to peel the top pull-off free, leaving you with only the screen protector protecting the camera glass.
I like the Sprint gel case but it doesn't protect the camera glass. I do like the Otterbox which really protects the whole deal but it's expensive and just makes the phone too big for my taste. Here, at least I have some protection and if keys, a drop, or anything scratches the protector near one of the camera lenses, I can just peel off and repeat the above. The above seems long because I tried to cover all the details but it's really pretty easy.
Mike
Nice write up. But I would think that a protector over the lenses would cause distortion and lower quality pics. Personally, I just use a TPU case with separate openings for the cameras, leds, and speaker. That way the raised case around the lenses prevent them from getting scratched when laying the phone on a flat surface.
I did this as soon as I got the phone and here's what I came up with. First, you can take the battery cover off of the back and use the hole as the trace stencil. You will however have to trace and cut another hole for the flash or all your flash photography will have a blue glow from it lighting up the protector sitting on the lenses.
Sent from my PG86100 using XDA Premium App
nice write up....except this company sells them.
EDIT - XDA won't let me post outside links. google phantom skinz
it comes with the area just around the lens cut out so it does not affect picture quality. i bought a set of these and they come with 2 sets, 2 front and 2 rear.
Post pics
Sent from my PG86100 using XDA App
mcmikecruz1 said:
Post pics
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
sorry OP, not trying to hijack your thread. i actually was going to try what you did until i found these. thought id save myself the headache since i suck at stuff like that.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
MFD00M said:
sorry OP, not trying to hijack your thread. i actually was going to try what you did until i found these. thought id save myself the headache since i suck at stuff like that.
Click to expand...
Click to collapse
Thanks I ment his mod I can never cut curves right
Sent from my PG86100 using XDA App
jnewkirk10 said:
I did this as soon as I got the phone and here's what I came up with. First, you can take the battery cover off of the back and use the hole as the trace stencil. You will however have to trace and cut another hole for the flash or all your flash photography will have a blue glow from it lighting up the protector sitting on the lenses.
Sent from my PG86100 using XDA Premium App
Click to expand...
Click to collapse
No glow here and the photos are just as sharp as without the protector on. I've taken some flash shots with the protector on and I've compared macro shots of flowers. The flash doesn't cause any glow on the protector and there is no discernible distortion. Of course, it might depend on the type/brand screen protector you are using. You really have to use a crystal clear one.
Mike
Here's a flower I shot after I put the protector on.
I still need to do this. I have heard people say that leaving the protector covering the LEDs causes a glare/glow in photos taken using the flash, but if you say otherwise, then that saves me the trouble of having to cut a hole for the LEDs.
I'm looking for the best screen protector. Most important is functionality, so the least amount of stylus/touch sensitivity reduction.
I've tried the armorsuit military shield that uses liquid applicator and it causes too much friction and sensitivity reduction.
I'm now looking at the various generic film protectors and the 1 glass protectors linked below
intelliGLASS https://www.amazon.com/dp/B00TD9G9R2/ref=cm_sw_r_awd_WSgevb1JDHSXF
Glass protectors offer the best damage protection. I'm curious as to the performance with this shield.
Has anyone tried it?
I have, and the screen protector does not seem to affect stylus or touch functionality in any way
Sent from my SHIELD Tablet using Tapatalk
2me3 said:
I'm looking for the best screen protector. Most important is functionality, so the least amount of stylus/touch sensitivity reduction.
I've tried the armorsuit military shield that uses liquid applicator and it causes too much friction and sensitivity reduction.
I'm now looking at the various generic film protectors and the 1 glass protectors linked below
intelliGLASS https://www.amazon.com/dp/B00TD9G9R2/ref=cm_sw_r_awd_WSgevb1JDHSXF
Glass protectors offer the best damage protection. I'm curious as to the performance with this shield.
Has anyone tried it?
Click to expand...
Click to collapse
Glass is always incredible, and this one is no exception. Quality and packaging is great. I like the slight curves on the edges of the protector, makes it feel nice to the touch. I showed off my tablet to family to check it out, and until I told them it had a screen protector on, they couldn't tell what I'd added to it LOL.
I ordered the intelliARMOR intelliGLASS HD for mine. It's arrived however still waiting on my tablet to return from Nvidia (FedEx says Tuesday!) so it can try it on lol
Hoping it doesn't interfere with the case.
2me3 said:
I'm looking for the best screen protector. Most important is functionality, so the least amount of stylus/touch sensitivity reduction.
I've tried the armorsuit military shield that uses liquid applicator and it causes too much friction and sensitivity reduction.
I'm now looking at the various generic film protectors and the 1 glass protectors linked below
intelliGLASS https://www.amazon.com/dp/B00TD9G9R2/ref=cm_sw_r_awd_WSgevb1JDHSXF
Glass protectors offer the best damage protection. I'm curious as to the performance with this shield.
Has anyone tried it?
Click to expand...
Click to collapse
Chris_c81 said:
I ordered the intelliARMOR intelliGLASS HD for mine. It's arrived however still waiting on my tablet to return from Nvidia (FedEx says Tuesday!) so it can try it on lol
Hoping it doesn't interfere with the case.
Click to expand...
Click to collapse
I've been using it since I bought my Shield and its great! I can upload some pictures of it on my Shield if you want to see how it looks. There is a small cutout for the sensor on the middle upper right but other than that its an edge to edge fit (as much as it can)
Pilz said:
I've been using it since I bought my Shield and its great! I can upload some pictures of it on my Shield if you want to see how it looks. There is a small cutout for the sensor on the middle upper right but other than that its an edge to edge fit (as much as it can)
Click to expand...
Click to collapse
Do you use the official case with it mate? Does it fit well? I've had their glass products before on my HTC ONE M8 and been pleased with the quality.
Chris_c81 said:
Do you use the official case with it mate? Does it fit well? I've had their glass products before on my HTC ONE M8 and been pleased with the quality.
Click to expand...
Click to collapse
If you are referring to the magnetic folio cover then yes that's all I use with a vinyl wrap on the back to prevent scratches. There are no issues at all other than the screen protector getting dirty from the folio but the smudges wipe right off.
Pilz said:
If you are referring to the magnetic folio cover then yes that's all I use with a vinyl wrap on the back to prevent scratches. There are no issues at all other than the screen protector getting dirty from the folio but the smudges wipe right off.
Click to expand...
Click to collapse
Yeah that's the one. Excellent, thanks mate. Can't wait to get my tablet back now. Missing playing VainGlory on it! Playing on the smaller phone screen just doesn't compare lol
Chris_c81 said:
Yeah that's the one. Excellent, thanks mate. Can't wait to get my tablet back now. Missing playing VainGlory on it! Playing on the smaller phone screen just doesn't compare lol
Click to expand...
Click to collapse
My last RMA was in that recall but I had to RMA it for a different reason. Thankfully my new one (I recieved it about a month ago) is working great and doesn't have the defective battery. I usually play games on my Shield TV now but I still enjoy gaming on the tablet.
Pilz said:
My last RMA was in that recall but I had to RMA it for a different reason. Thankfully my new one (I recieved it about a month ago) is working great and doesn't have the defective battery. I usually play games on my Shield TV now but I still enjoy gaming on the tablet.
Click to expand...
Click to collapse
Coincidentally I RMA'd my Shield Tablet last Monday for a broken LCD beneath the glass. Crack occurred for no particular reason, I had never dropped it. All I recall is the night before it got quite hot. Don't think it's related to the battery issue but I'm convinced the heat of it had something to do with the crack. They accepted and my replacement was sent out yesterday due delivery Tuesday. I'm assuming it'll be a model with the unaffected battery else I'll have to RMA again...!
Chris_c81 said:
Coincidentally I RMA'd my Shield Tablet last Monday for a broken LCD beneath the glass. Crack occurred for no particular reason, I had never dropped it. All I recall is the night before it got quite hot. Don't think it's related to the battery issue but I'm convinced the heat of it had something to do with the crack. They accepted and my replacement was sent out yesterday due delivery Tuesday. I'm assuming it'll be a model with the unaffected battery else I'll have to RMA again...!
Click to expand...
Click to collapse
That's good to hear, mine was an advanced RMA so I had it in 2 days and sent the original back without any issues. My original one was almost non functional after downgrading from the original 3.0 back to 2.2.1 and no matter how many times I flashed the stock image or a different ROM it stuttered and froze. They suspected there might have been hardware damage from the OTA 3.0 somewhere in the CPU/GPU which doesn't make sense and they never gave me an answer on what was wrong. I'm still glad this one is working better, in fact I'm typing this reply on it.
Applied the IntelliGlass by IntelliArmor to my Shield today. Here's my impressions and mini-review.
The protector comes well packaged in a book style packaging. You get everything you'll need inside to make applying the protector a breeze. Includes:
- protector
- dust removal sheet
- alcohol wipe
- lint free cloth
- smudger
Simply cleaned the screen with the wipe, applied the dust removal sheet several times and then began peeling off the backing and lining up the glass protector. My first hit was slightly off, enough to irritate me anyway! So had to gently prise it off and re-seat it. Second hit was perfect. The bubbles smoothed out easily with my thumb pressure.
I've had IntelliArmor products before and as with all glass protection I've owned in the past, they are the ultimate screen protection and offer so much more then plastic ones. The best advantage for me though is that your finger feels like its on the actual screen as plastic protectors can give differing feeling under the finger.
I've been unlucky enough to drop my phone before onto a hard surface and if it were not protected by a glass screen protector, I'm confident the screen would have shattered. Instead the screen was fine below the shattered and chipped glass protector. So I've had first hand experience that glass protectors do the job. I've no reason to believe any different of this product, without me chucking my Shield on the floor - which I won't do for a review!
The glass is not too thick and plays nicely with the Official Nvidia case which is an added bonus as not all glass protectors play well with flip style cases. Fortunately this one does.
My only gripe at the moment is when swipe typing. It currently seems a bit hindered by the glass protector. However, I need more time with it as I'm not 100% convinced it has all to do with the protector.
If you're in the market for a Shield screen protector, then I highly recommend the IntelliGlass. Worth the extra £'s in my humble opinion.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Chris_c81 said:
Applied the IntelliGlass by IntelliArmor to my Shield today. Here's my impressions and mini-review.
The protector comes well packaged in a book style packaging. You get everything you'll need inside to make applying the protector a breeze. Includes:
- protector
- dust removal sheet
- alcohol wipe
- lint free cloth
- smudger
Simply cleaned the screen with the wipe, applied the dust removal sheet several times and then began peeling off the backing and lining up the glass protector. My first hit was slightly off, enough to irritate me anyway! So had to gently prise it off and re-seat it. Second hit was perfect. The bubbles smoothed out easily with my thumb pressure.
I've had IntelliArmor products before and as with all glass protection I've owned in the past, they are the ultimate screen protection and offer so much more then plastic ones. The best advantage for me though is that your finger feels like its on the actual screen as plastic protectors can give differing feeling under the finger.
I've been unlucky enough to drop my phone before onto a hard surface and if it were not protected by a glass screen protector, I'm confident the screen would have shattered. Instead the screen was fine below the shattered and chipped glass protector. So I've had first hand experience that glass protectors do the job. I've no reason to believe any different of this product, without me chucking my Shield on the floor - which I won't do for a review!
The glass is not too thick and plays nicely with the Official Nvidia case which is an added bonus as not all glass protectors play well with flip style cases. Fortunately this one does.
My only gripe at the moment is when swipe typing. It currently seems a bit hindered by the glass protector. However, I need more time with it as I'm not 100% convinced it has all to do with the protector.
If you're in the market for a Shield screen protector, then I highly recommend the IntelliGlass. Worth the extra £'s in my humble opinion.
]
Click to expand...
Click to collapse
I'm glad to see its working well for you. I wouldn't use my tablet without one know how clumsy I can be.
Chris_c81 said:
Applied the IntelliGlass by IntelliArmor to my Shield today. Here's my impressions and mini-review.
The protector comes well packaged in a book style packaging. You get everything you'll need inside to make applying the protector a breeze. Includes:
- protector
- dust removal sheet
- alcohol wipe
- lint free cloth
- smudger
Simply cleaned the screen with the wipe, applied the dust removal sheet several times and then began peeling off the backing and lining up the glass protector. My first hit was slightly off, enough to irritate me anyway! So had to gently prise it off and re-seat it. Second hit was perfect. The bubbles smoothed out easily with my thumb pressure.
I've had IntelliArmor products before and as with all glass protection I've owned in the past, they are the ultimate screen protection and offer so much more then plastic ones. The best advantage for me though is that your finger feels like its on the actual screen as plastic protectors can give differing feeling under the finger.
I've been unlucky enough to drop my phone before onto a hard surface and if it were not protected by a glass screen protector, I'm confident the screen would have shattered. Instead the screen was fine below the shattered and chipped glass protector. So I've had first hand experience that glass protectors do the job. I've no reason to believe any different of this product, without me chucking my Shield on the floor - which I won't do for a review!
The glass is not too thick and plays nicely with the Official Nvidia case which is an added bonus as not all glass protectors play well with flip style cases. Fortunately this one does.
My only gripe at the moment is when swipe typing. It currently seems a bit hindered by the glass protector. However, I need more time with it as I'm not 100% convinced it has all to do with the protector.
If you're in the market for a Shield screen protector, then I highly recommend the IntelliGlass. Worth the extra £'s in my humble opinion.
View attachment 3427492
View attachment 3427493
View attachment 3427494
Click to expand...
Click to collapse
Q: dirt under the neckline falls?
Brigadir120370 said:
Q: dirt under the neckline falls?
Click to expand...
Click to collapse
I have no idea what you just said.
Chris_c81 said:
I have no idea what you just said.
Click to expand...
Click to collapse
Sorry for the bad translation! I ask you: dust gets under the protection?:смущенный:
Brigadir120370 said:
Sorry for the bad translation! I ask you: dust gets under the protection?:смущенный:
Click to expand...
Click to collapse
Ah! Ok no problem.
No I've not experienced any dust gathering underneath the edges. It's a pretty good seal once it's on.
Chris_c81 said:
Ah! Ok no problem.
No I've not experienced any dust gathering underneath the edges. It's a pretty good seal once it's on.
Click to expand...
Click to collapse
Thank you so much!
Hey all, I've been seeing more of these clear glass back mods around, so I decided to do have some fun and do one for our Z2. Total time taken was under an hour, and I have a standard rear glass in case I want to restore back to stock later. Cost is < $5 USD. UPDATE: I have written a full step by step guide with instructions below, it's fairly straightforward.
RESULTS:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
INSTRUCTIONS:
Here is the step-by-step guide to how I did it. You don't have to buy a new back, since you can reuse your existing one, but I got another one anyway, since it's quite cheap and it's good to have a spare. They are < $USD 5 each for a replacement glass Z2 back shipped. NOTE: I am not responsible for any damage you do to your own phone, but this is a pretty safe operation generally speaking.
Prerequisites:
* Suction cup (a car windscreen phone holder will also work)
* Hairdryer or heat gun
* Business card or plastic prying tool
* Metal scraping tool of some type (a flathead screwdriver or razor blade will work)
* Thin double-sided tape (black)
* (Optional) Chemical paint remover (such as methylene chloride)
* (Optional) Spare glass back
* (Optional) Clear protective case so you can show off your phone!
Phone with optional spare back. I didn't use the spare back, but modified the stock back instead, you will see why later.
STEP 1: Remove back of case:
- The back glass is held on only by glue that goes around the outside edge. The glue will soften at a certain temperature.
- Use your heat gun (or hairdryer) to heat up the back glass till it becomes slightly too hot to touch.
- There are many videos showing how to open the back glass, including THIS ONE and THIS ONE.
- Once the back is heated up, use the suction cup to lift the glass up (preferably start at the top or bottom to get leverage), enough to slide a business card or plastic pry tool inside.
- Do not poke the card too far in, as there is a ribbon cable which can get caught.
- Reheat the glass and continue around the edge until the entire glass back is removed.
- Do not force the glass up or it will crack, if it takes alot of force, it means the glue somewhere has hardened. Reheat and retry gently. It should lift up easily.
STEP 2: Remove the camera lens frame:
- The only part which needs to be separated from the glass is the camera lens frame. It is a small metal box that is lightly glued in. Apply heat and carefully pull it out.
- Put the lens somewhere safe, you will be re-applying it back later. The glue can be re-used.
- If you order a new glass back, it does not come with a camera lens frame, do not lose it!
The glass removed from the phone, note the camera lens that needs to be removed:
STEP 3: Clean up residue:
- There will be a bunch of residual glue on the phone edge and the glass edge, just peel it off or use a scraper to peel it off.
- A very small flathead can be used to clean the phone side, you will notice a small 'lip' which the glass sits on.
- On the phone side, be careful not to let the small glue bits fall into the gaps, as you will see it all later.
Glue residue on phone side that needs to be cleaned:
STEP 4: Cleanse the glass
- This is the part which takes the most time.
- The paint of the back (whether you have white or black) is on the INSIDE of the glass.
- On top of the paint is another plastic protective layer. With a bit of heat, this can be easily peeled off (see below).
- Once that's done, you can apply some solvent and start scraping the paint off. The paint is not very strong and will remove fairly easily.
- (OPTIONAL) You can use paint remover (meythylene chloride) and soak the paint for a while, then it will just fall off without much scraping. This is much easier, but I did it the hard way since I did not have any paint remover.
- Use a metal tool like the edge of a screwdriver or a razer blade to start scraping. The metal is softer than the glass, so it will NOT scratch the glass at all.
- DO NOT use sandpaper, as the sand will probably scratch the glass.
- Once in a while, wipe off the glass on cloth, then hold up the glass to a white or flat background, then you can see any parts you missed.
- Be careful if you are working on a non-flat surface, if you poke too hard, it will bend and crack the glass. Also be careful around the edges, as you can chip the glass if you push too hard.
The plastic layer over the paint can be easily removed like old skin:
A few pokes and the paint easily comes off:
After all that, you have a clean piece of glass:
STEP 5: Replace the camera lens
- Remember that lens you removed from before? Time to put it back
- Make sure the glass is completely dry first!
- There is a bit of movement allowed in the glue, so doesn't have to 100% perfect alignment
- The frame will sit 'around' the camera when you put the glass back
Stick this back into the clean glass back:
STEP 6: Install the glass back
- You will need to apply double-sided tape around the edge of the phone for the glass to stick onto.
- The tape must sit ON TOP of the inner lip, but not outside the outer lip, or it will protrude from the glass.
- You don't need to cover 100% of the entire lip, but most of the main parts.
- Make sure you clean the inside of the glass first from dust and fingerprints, as it will be hard to get it back out again.
- Press the glass in, make sure that no tape is poking out from the outside. If it is, either use something to push it back in, or use a blade and carefully trim it.
Phone with double sided tape ready to apply glass
FINISHED! Enjoy your unique looking phone
If you want to restore the standard glass back later, just repeat steps 1-3 and use the replacement back you ordered.
Hopefully that helps, let me know your thoughts and results below.
Nice thanks for sharing
Updated first post with a detailed step by step with pictures
If anybody else does this, let me know how you go
SenK9 said:
Updated first post with a detailed step by step with pictures
If anybody else does this, let me know how you go
Click to expand...
Click to collapse
Nic like your work
Add some led in back
If possible
Attach this led with default led
Nice work.
Is there any replacement for the camera lens frame as mine has quite a lot of scratches on it. I'm worried that it might affect the picture quality if the number of scratches increase.
I already have a case installed but it seems that it wasn't able to save the lens from scratches. Is there any other alternative to protect the camera lens frame?
YamenAkhtar said:
Nice work.
Is there any replacement for the camera lens frame as mine has quite a lot of scratches on it. I'm worried that it might affect the picture quality if the number of scratches increase.
I already have a case installed but it seems that it wasn't able to save the lens from scratches. Is there any other alternative to protect the camera lens frame?
Click to expand...
Click to collapse
You might be able to get a frame separately but I haven't seen any around. Actually I'm not even sure if it's glass or plastic, if it's that latter you can repair scratches. As for protection, can't think of much, apart from a thicker case or cutting some leftover screen protector to size and put it on top.
SenK9 said:
You might be able to get a frame separately but I haven't seen any around. Actually I'm not even sure if it's glass or plastic, if it's that latter you can repair scratches. As for protection, can't think of much, apart from a thicker case or cutting some leftover screen protector to size and put it on top.
Click to expand...
Click to collapse
That is the only option.
Can you please let me know where can I find the glass back as mine has already some scratches on it and I have Butterfingers so the phone has fallen down couple of times, didn't break though. Just as a backup, can you provide a link below? Even a back tempered glass would work.
YamenAkhtar said:
That is the only option.
Can you please let me know where can I find the glass back as mine has already some scratches on it and I have Butterfingers so the phone has fallen down couple of times, didn't break though. Just as a backup, can you provide a link below? Even a back tempered glass would work.
Click to expand...
Click to collapse
https://www.aliexpress.com/item/Ori...sing-Door-Case-free-shipping/32799539511.html
This is the one I got, in the picture it looks brand-less, but it actually has a ZUK logo on it. I compared it side by side with my original and could not tell any difference. There might also be some on Flipkart.
Thanks.. Thinking of buying a zuk z2 now
My Phone
Z2 Plus
THIS' SICK!
phone looks Badass
aslam2121 said:
Z2 Plus
Click to expand...
Click to collapse
In the pictures that you've posted, what are the stains/marks in the bottom end and bottom left corner?
What type of glue should we use for sticking the back again
SenK9 said:
https://www.aliexpress.com/item/Ori...sing-Door-Case-free-shipping/32799539511.html
This is the one I got, in the picture it looks brand-less, but it actually has a ZUK logo on it. I compared it side by side with my original and could not tell any difference. There might also be some on Flipkart.
Click to expand...
Click to collapse
Can you upload valid and actual link for this item? This one is dead. Thanks!
SenK9 said:
Updated first post with a detailed step by step with pictures
If anybody else does this, let me know how you go
Click to expand...
Click to collapse
I did it successfully thanks for the help
Does it work with the Z2 Pro too?
I want back glass door Black can u give me link
re
1thesandy1 said:
I want back glass door Black can u give me link
Click to expand...
Click to collapse
Search yourself. For the reason I am a good person, I'll give you the websites where you can find glass back: aliexpress, ebay.
We made a video based on this thread
Hey we just made a video based on this thread. A video showing how to clear back zuk z2.
Here's the video link :- https://www.youtube.com/watch?v=UPwWwD7lg2Y
It will be helpful if you add the the video to the main post..
To everyone who did this mod: do you guys notice any gap between the mainboard and the back panel? Is there any gap to put a thermal pad in to help with cooling?
The title pretty much covers it. I see many questions on this, but no definitive answers. I tried the official one but returned it since it would cover the edges of the screen. Bought one off of Amazon that said it didn't do that, but it did as well.
So simply, I'm looking for one that won't cover the screen is good quality. Simple enough, no?
I bought this case by Nillkin for my phone and it came with a free screen protector film (not a glass protector) and I find it pretty decent. I didn't find any issues with fingerprints on it.
You can find it here: https://www.amazon.com/OnePlus-Nill...=1504853058&sr=8-3&keywords=oneplus+5+nillkin
The Nillkin TGSP is probably the most compatible at the moment but it does have the larger gap around the edges, I've still got mine applied, hoping for more luck with the Rhinoshield case and a full face protector as the case is supposed to be much more compatible with them, my advice would be to go for the Nillkin until we all find the perfect replacement.
http://www.dx.com/p/naxtop-tempered...for-oneplus-5-transparent-470989#.WbOz7iNnp74
Anyone tried this one?
Transparent or with black borders?
dasti555 said:
http://www.dx.com/p/naxtop-tempered...for-oneplus-5-transparent-470989#.WbOz7iNnp74
Anyone tried this one?
Transparent or with black borders?
Click to expand...
Click to collapse
Thanks. Looks interesting particularly the all transparent version, curved edges and its cheap enough to experiment. There is no indication on where the adhesion is and no specific mention of a Oleophoic coating but describes an anti-fingerprint coating. I currently have the under screen dust issue with my Orzly tgsp but I love the feel of that screen so am looking for a alternative protector with similar finger feel.
I'm suspecting that my bumper case is causing the Orzly's issue as the dust only comes from the volume rocker area and likely due to the case pushing the Orzly's edge when pressed. Maybe this alternate protector with the curved edges would not have the same issue, while the all transparent version would likely have no issues cutting off the screen view unless the curved edge causes some undesirable optical effect.
If you get one please post your observations.
3DSammy said:
Thanks. Looks interesting particularly the all transparent version, curved edges and its cheap enough to experiment. There is no indication on where the adhesion is and no specific mention of a Oleophoic coating but describes an anti-fingerprint coating. I currently have the under screen dust issue with my Orzly tgsp but I love the feel of that screen so am looking for a alternative protector with similar finger feel.
I'm suspecting that my bumper case is causing the Orzly's issue as the dust only comes from the volume rocker area and likely due to the case pushing the Orzly's edge when pressed. Maybe this alternate protector with the curved edges would not have the same issue, while the all transparent version would likely have no issues cutting off the screen view unless the curved edge causes some undesirable optical effect.
If you get one please post your observations.
Click to expand...
Click to collapse
Well I post it here because I was looking if somebody already bought it. I have orzly with I'm happy however it have rainbow effect in the middle and sometimes it's quiete visible. My friend told me that he bought that one from link I sent (with black borders) and he is told me he don't have rainbow effect or cutted screen.. so i don't know
Like you I'm more interested in the transparent one as I don't know why there is even a black version on any of them.
On my Orzly I've seen the rainbow effect but only when the screen is at an unusual angle while wiping the surface clean but never when using the phone normally. It's only the dust that is driving me crazy. I'm even considering going with just my bumper case and no protector but I'll wait a while before going that route.
This one looks interesting (not glass though), quite clever application method, reminds me of the default screen protector that comes with the phone that a lot of people seem to like
Ringke Invisible Defender Screen Protector
https://www.amazon.com/Protector-Invisible-Guaranteed-Compatible-Clearness/dp/B074137YDH/
Just read the Amazon reviews and they're not that positive.
I still have to receive my oneplus 5. Would you guys recommend keeping the pre-applied film with the orzly bumper over any screenprotector that's on the market now?
ned4spd8874 said:
The title pretty much covers it. I see many questions on this, but no definitive answers. I tried the official one but returned it since it would cover the edges of the screen. Bought one off of Amazon that said it didn't do that, but it did as well.
So simply, I'm looking for one that won't cover the screen is good quality. Simple enough, no?
Click to expand...
Click to collapse
i am in the same boat as you.
found this -
imak Oneplus 5 Transparent Clear Full Cover Edges 0.15mm TPU LCD Screen Protector for Oneplus 5 back Anti-shock Protective Film
http://s.aliexpress.com/BBBjERbi
(from AliExpress Android)
i just want clear protective glass that covers the whole screen. anything similar to whitestone dome protective glass (for s8) would be great.
I bought the one from Nillkin until a better one came along. However it was pure garbage. It didn't fit the whole screen and the top notch was way off center. But the main reason I threw it in the trash was there was the entire right side would not stick to my phone. There was a good 1/8" section all along the right edge that was not sticking and just looked like crap.
Finally the almost perfect tgsp.....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Almost perfect is because its not fully adhesive. Only perimeter adhesive.
so dust will appear along the sides and rainbow will appear sooner or later.
spawn549 said:
Finally the almost perfect tgsp.....
Almost perfect is because its not fully adhesive. Only perimeter adhesive.
so dust will appear along the sides and rainbow will appear sooner or later.
Click to expand...
Click to collapse
Which one is it
i dont recommend it. after few hours of usage tiny dust appearing from speaker and sensor holes going right inside the tgsp. the coating is bad. attracts fingerprint n dust. screen will smudge all over.
srt99 said:
i am in the same boat as you.
found this -
imak Oneplus 5 Transparent Clear Full Cover Edges 0.15mm TPU LCD Screen Protector for Oneplus 5 back Anti-shock Protective Film
http://s.aliexpress.com/BBBjERbi
(from AliExpress Android)
i just want clear protective glass that covers the whole screen. anything similar to whitestone dome protective glass (for s8) would be great.
Click to expand...
Click to collapse
I just picked up two packs for fun - will report back.
spawn549 said:
i dont recommend it. after few hours of usage tiny dust appearing from speaker and sensor holes going right inside the tgsp. the coating is bad. attracts fingerprint n dust. screen will smudge all over.
Click to expand...
Click to collapse
Got it, but wich brand produce this one? Just to look around
No brand packaging on it...i would stay away from non full adhesive due to it attracts dust and rainbow effect. I would rather use a full adhesive tgsp eventhough it will block few mm from the sides
This is the best I found for now. Not full covered but minimal bars on the side and almost no rainbow effect. After 2 weeks no dust at all.
https://fr.aliexpress.com/item/Scre...lus-3-3T-Three-1-3-1-3T-Full/32795224827.html
bibi98 said:
This is the best I found for now. Not full covered but minimal bars on the side and almost no rainbow effect. After 2 weeks no dust at all.
https://fr.aliexpress.com/item/Scre...lus-3-3T-Three-1-3-1-3T-Full/32795224827.html
Click to expand...
Click to collapse
Do you also use a case with this protector? If you do please indicate which one as even an all adhesive tgsp can be lifted by many of the cases being sold.
Disgustip8ed said:
I just picked up two packs for fun - will report back.
Click to expand...
Click to collapse
Anything new about those glass screen protectors?