Let's try unbrick X722
You ask the same thing in several threads.
We offer tests but few comments results.
After several days the people with bricks disappear. Fixed up?
I suggest that anyone who has brick, write it, but if we propose a solution, say whether it works or not, to discard it
We can have 2 cases: hard brick and soft brick.
Hard brick of impossible moment. Requires zip qfil. It is proposed to build one.
Brick soft with fastboot function. Here you can do tests.
Who has a brick ?, publish how it came, and if you have fastboot.
Greetings.
P.S. Sorry for the English. I use a translator
Possible soft brick solution ...
Possible hard brick solution ...
F.J.V said:
Possible soft brick solution ...
Click to expand...
Click to collapse
I installed the 26 s with twrp
soft brick because it goes into fastboot, it enters edl mode.
does not enter recovery mode in any way.
different startup screens by pressing and holding the power button for more than 20 seconds.
I tried all the procedures by using minimal adb and fastbooot without any results
I have two options, I am in Italy, but I strongly doubt it, or send it back to bangood that I have already contacted, or buy another, I'm following over xda, pda, leeco.re, androids.op? sorry.
from the tests I did between a while do not even work the buttons
if you have any questions i can answer.scusate google translate
I seem to have realized that the phone has in the recovery twrp and the recovery stock, failing to decide which start, so it stops at boot, if i try to delete with adb either the stock recovery or twrp tells me ok.
if I try to install the stock or twrp tells me failed
I got this discussion on facebook for n cool1.I wonder if it can work on x722? "If you're interested in getting the device started, I unpacked the firmware file with YGPD and flashed directly that with MiFlash in edl mode. lack of IMEI, but after solving I'm hard brick, I'm scared no more !!! "
YGPD is Coolpad (Yulong) Flayhing Tool and it makes temp folders on C disk during flash preparation.
You could make recovery replacement hack while flashing some coolpad phones.
Try this:
Download Recovery.zip
Decompress.
recstock722.img is recovery stock 722.
Copy recstock722.img to fastboot folder
Open Command Window in Fastboot Folder
writes:
fastboot boot recstock722.img
This does not flashea recovery, only charge on phone.
If all goes well the phone restarts in recovery stock.
Load update.zip (5.8.001D) with recovery.
If I succeed flash another rom and another recovery
Greetings.
[/COLOR]
F.J.V said:
Try this:
Download Recovery.zip
Decompress.
recstock722.img is recovery stock 722.
Copy recstock722.img to fastboot folder
Open Command Window in Fastboot Folder
writes:
fastboot boot recstock722.img
This does not flashea recovery, only charge on phone.
If all goes well the phone restarts in recovery stock.
Load update.zip (5.8.001D) with recovery.
If I succeed flash another rom and another recovery
Greetings.
Click to expand...
Click to collapse
https://imageshack.com/i/pnfE9OeIp
Has the 26s entered the unlock code for the bootloader?
x722 For people who can not charge the phone being in soft brick
If you have the phone that does not charge anymore
connect it to the mains power supply
press volume up and down together and power key
only release when you hear half-vibration
the charging LED lights up
I have a Hard Brick... i lost my hopes..
ste73 said:
https://imageshack.com/i/pnfE9OeIp
Has the 26s entered the unlock code for the bootloader?
Click to expand...
Click to collapse
No.
I have stock rom 20S bangood unmodified
vsrocha said:
I have a Hard Brick... i lost my hopes..
Click to expand...
Click to collapse
Nothing at the moment, but ...
Does it go into EDL mode?
To enter EDL mode:
Press (vol +), (vol-) and plug into the PC.
If the PC recognizes 9008 you have to wait for qfil.
F.J.V said:
Nothing at the moment, but ...
Does it go into EDL mode?
To enter EDL mode:
Press (vol +), (vol-) and plug into the PC.
If the PC recognizes 9008 you have to wait for qfil.
Click to expand...
Click to collapse
Yes, recognizes, i don't need Press (vol +), (vol-) just plug.
Check this...
http://www.leeco.re/topic/2592-hard-bricked-x722/?do=findComment&comment=53338
vsrocha said:
I have a Hard Brick... i lost my hopes..
Click to expand...
Click to collapse
because brick hard
ste73 said:
because brick hard
Click to expand...
Click to collapse
i install miui 8 but i did not know the diference between X720 e X722, after this i had soft brick...
and my anxious speak loud and i install a fast rom for X720...
mate... too bad has three models and diferents roms.
I just read ROM for Le Pro 3 and install soon.
:crying:
I have a silly question, isn't possible change the Qfil le_zl1_qfil_ufs for X722, the unic difference between them is X720 Snapdragon 821 and X722 Snapdragon 820?
F.J.V said:
Nothing at the moment, but ...
Does it go into EDL mode?
To enter EDL mode:
Press (vol +), (vol-) and plug into the PC.
If the PC recognizes 9008 you have to wait for qfil.
Click to expand...
Click to collapse
With Le Eco in financial troubles, it's unlikely they will release the qfil that is needed. I'm thinking of sending back my hard brick X722 to the vendor I bought it from, and just ask how much it would cost to get if fixed.
Try this modified qfil ROM.
modqfil_ufs.zip
It's not official.
It is qfil 720 with some X722 files.
I do not promise anything.
Do not try if you do not have brick
Comment results.
Greetings.
F.J.V said:
Try this modified qfil ROM.
modqfil_ufs.zip
It's not official.
It is qfil 720 with some X722 files.
I do not promise anything.
Do not try if you do not have brick
Comment results.
Greetings.
Click to expand...
Click to collapse
downloading!! :fingers-crossed:
Don't work for me.
After descompress show this error.
Flash file not found, please make sure QFIL flash file is correct.
Does anyone know how to translate the scripts?
https://imageshack.com/i/potoxDAkj
https://imageshack.com/i/pnyUkScQj
depending on how I press the power button
ste73 said:
Does anyone know how to translate the scripts?
https://imageshack.com/i/potoxDAkj
https://imageshack.com/i/pnyUkScQj
depending on how I press the power button
Click to expand...
Click to collapse
Hello, no idea of Chinese.
I compared it with my terminal, I think I recognize the screens.
The first:
http://imageshack.com/i/potoxDAkj
This leaves when I'm in EDL and restart. This screen exits and starts normal.
The second:
http://imageshack.com/i/pnyUkScQj
This leaves when I'm in recovery and restart. This screen exits and starts normal.
The two screens precede the boot, it depends on where you restart.
Every time you do some testing, even if nothing seems to happen, boot into fastboot and try unlocking.
Greetings.
Related
Hello my friend just made an update of his phone which is a redmi 3 pro
His little bro shutdowned the phone while update was in process. The result is that now the phone have a bootloop, can't access the recovery (blackscreen when trying) and have a locked bootloader.
So I am not sur how to unlock the BL if I can't install a dev rom and can't boot. Not sur how to get into the recovery with the 2 same problems.
Could anyone help me for this one? Which is hard to me.
Thanks
PS: I tried to do something with unpacking boot and remove a ",verify" thing in the ramdisk but I guess I'll need the unlockedbootloader to flash the new boot.img?
Kicroy said:
Hello my friend just made an update of his phone which is a redmi 3 pro
His little bro shutdowned the phone while update was in process. The result is that now the phone have a bootloop, can't access the recovery (blackscreen when trying) and have a locked bootloader.
So I am not sur how to unlock the BL if I can't install a dev rom and can't boot. Not sur how to get into the recovery with the 2 same problems.
Could anyone help me for this one? Which is hard to me.
Thanks
PS: I tried to do something with unpacking boot and remove a ",verify" thing in the ramdisk but I guess I'll need the unlockedbootloader to flash the new boot.img?
Click to expand...
Click to collapse
I have the similar problem with my Redmi3. The Fastboot screen is the only screen that I can get now. Let me know if you have answer. Thanks.
If you can acces fastboot then just connect the phone to computer in fastboot and enter fastboot oem edl in cmd (maybe you will need Minimal ADB and fastboot to do it). Then flash official ROM via MiFlash.
ohoh seems interesting then it won't say couldn't verify or smthg? will tell that to my friend asap, thanks
EDL mode allows flashing with locked bootloader. Some models have this mode locked, but I think that is not the case with Redmi 3.
Kicroy said:
ohoh seems interesting then it won't say couldn't verify or smthg? will tell that to my friend asap, thanks
Click to expand...
Click to collapse
to go to edl mode just turn off your phone.plug the cable to your laptop or desktop but not to your phone.now be ready to press both volume up and down button as you plug the usb cable to ur phone.immediately after inserting the usb cable press both volume buttons at the same time.it should vibrate and go to edl mode.edl mode appears in black screen so to know if its in edl mode or not open miflash and click refresh ,your device should be shown as com10,20 or com something like that .once you go to edl mode you know what to do if you have used miflash to flash roms.hope this helps you.
jokerpappu said:
to go to edl mode just turn off your phone.plug the cable to your laptop or desktop but not to your phone.now be ready to press both volume up and down button as you plug the usb cable to ur phone.immediately after inserting the usb cable press both volume buttons at the same time.it should vibrate and go to edl mode.edl mode appears in black screen so to know if its in edl mode or not open miflash and click refresh ,your device should be shown as com10,20 or com something like that .once you go to edl mode you know what to do if you have used miflash to flash roms.hope this helps you.
Click to expand...
Click to collapse
I have a problem with my redmi 3. It makes reboot and it does not charge if its not closed.
Can you help me to fix or do you now where i can find a solution.....
geuthym said:
I have a problem with my redmi 3. It makes reboot and it does not charge if its not closed.
Can you help me to fix or do you now where i can find a solution.....
Click to expand...
Click to collapse
Well about that i dont know.but your best bet to solve it is by changing the software.if that does not helps then you should take your device to a technician for repairing.
jokerpappu said:
Well about that i dont know.but your best bet to solve it is by changing the software.if that does not helps then you should take your device to a technician for repairing.
Click to expand...
Click to collapse
When i bouht it the software it was unnoficial then i put with miflash the china dev. All the problem start when i make updates apps and the android web view.
geuthym said:
When i bouht it the software it was unnoficial then i put with miflash the china dev. All the problem start when i make updates apps and the android web view.
Click to expand...
Click to collapse
try flashing official global rom then see if the problem still persists or not
Hey! I am back with some news of my friend!
He tried to run the EDL mode but when he does that the phone simply goes into the bootloop again... He asked a vendor from Aliexpress to get a french rom, is there a way that the phone doesn't have EDL because of the rom or something like that? I mean is EDL a hardware-thing or a software-thing
same problem
cukru said:
If you can acces fastboot then just connect the phone to computer in fastboot and enter fastboot oem edl in cmd (maybe you will need Minimal ADB and fastboot to do it). Then flash official ROM via MiFlash.
Click to expand...
Click to collapse
I have same problem, but this way is not work, because bootloader is locked. Im forget for replacing recovery.img in update package with twrp.
I had this problem before few monthes
my solution was to "force" putting this device on EDL mode
I clicked on vol up + vol down + power together and got into EDL mode, then miflash it.
google - xiaomi understanding download mode
it will send you into miui forum
then second method, download mode, it is what I've described
So, i installed Xposed, and like many people, i got stuck in the logo... No big deal there... Went to look for some help, and it said to go to fastboot, so I went, but it got stuck in the fastboot logo. Then I connected it to the computer and when I try to list the ADB devices I Ialways get an error saying the server is outdated...
I really need some help! I can't find anything online to help me!
Thanks in advance!
Edit: I submitted a bootloader unlock request to Xiaomi earlier today, but I can't see if its approved or not because phone doesn't work
well,
if you are in fastboot mode then the command is "Fastboot Devices", Not "adb Devices"
_____________________________________________
and about boot loop problem try to flash miui fastboot rom.
_____________________________________________
And about bootloader request problem you can go to edl mode and flash miui without any permissions
Thanks:good::good:
nishant2222 said:
well,
if you are in fastboot mode then the command is "Fastboot Devices", Not "adb Devices"
_____________________________________________
and about boot loop problem try to flash miui fastboot rom.
_____________________________________________
And about bootloader request problem you can go to edl mode and flash miui without any permissions
Thanks:good::good:
Click to expand...
Click to collapse
I tried, but i cant seem to go to edl mode through fastboot, any tips? and because of bootloader lock i cant flash fastboot rom with MI Flash
Edl mode needs a specific fastboot version.
For the Redmi Note 3 Pro / Special Edition
Download and extract this package on your PC.
Enter fastboot mode by holding Power and Vol- at the same time. Wait until the Mi Bunny appears, then connect the phone to the PC.
Run reboot.bat in the extracted package. A command prompt will appear. Press a key to reboot the phone to EDL mode.
Upon entering EDL mode, the screen should turn blank. The notification LED might be blinking red. Done.
To get out of EDL mode, hold the Power button for about 10 seconds.
Click to expand...
Click to collapse
Above quote taken from xiaomi reddit wiki.
If the above doesn't work, see the link for deep flash cable, shouldn't be need for kenzo/kate.
How you flashed/installed xposed on locked bootloader is another question?
You may need to update your adb/fastboot version + device drivers(adb)
corkiejp said:
Above quote taken from xiaomi reddit wiki.
If the above doesn't work, see the link for deep flash cable, shouldn't be need for kenzo/kate.
How you flashed/installed xposed on locked bootloader is another question?
You may need to update your adb/fastboot version + device drivers(adb)
Click to expand...
Click to collapse
Ok, so when i try to reboot in edl, it just reboots as normal after screen goes blank...
I installed Xposed with an APK
Sorry if i'm being annoying, but I just want this fixed
KaiZix said:
Ok, so when i try to reboot in edl, it just reboots as normal after screen goes blank...
I installed Xposed with an APK
Sorry if i'm being annoying, but I just want this fixed
Click to expand...
Click to collapse
Mate, watch any video on YouTube. You're not understanding from text instructions.
AtomR said:
Mate, watch any video on YouTube. You're not understanding from text instructions.
Click to expand...
Click to collapse
Can't find any... Recommendations?
EDL Mode: - https://www.youtube.com/watch?v=LDGViyDYPbU
If you can't get into EDL mode, you may need to use the deep flash cable method.
corkiejp said:
EDL Mode: - https://www.youtube.com/watch?v=LDGViyDYPbU
If you can't get into EDL mode, you may need to use the deep flash cable method.
Click to expand...
Click to collapse
I can't get into EDL mode, and I can't make/buy a deep flash cable... I'm getting really scared now...
About ADB, how can I fix it?
KaiZix said:
I can't get into EDL mode, and I can't make/buy a deep flash cable... I'm getting really scared now...
About ADB, how can I fix it?
Click to expand...
Click to collapse
Installing Mi Flash should have put the correct drivers on your PC.
But can be got from here: - https://xiaomifirmware.com/downloads/download-pc-drivers-xiaomi-redmi-note-3/
And I already linked adb/fastboot tools.
IF your comfortable opening your device, there is also a test point method you could try.
http://en.miui.com/thread-244814-1-1.html
Could not find a English video, so maybe try googling more and you might find one.
If not, you could ask at local repair shop, if they would fix it for you. Using Cable/ TP method.
Note for other readers:- MIUI roms need a special version of xposed, for it to work. And installing from an app would more than likely would have use the wrong version. Should never be done on a locked bootloader, only asking for trouble. (Rovo89 is currently trying to bring MIUI support to the official version for nougat roms)
Hii Friends,
I am new to xda as i got an problem with my Redmi Note 3.
Specs Before Dead:
Miui 8.2.4
Android 6.0
32 Gb Rom,3 Gb Ram
I was trying to flash Android 8.0 Rom via Twrp {Flashed Through Mi Flash Tool}. Twrp Flashed Successfully and Then I started with flashing with Oreo Rom.It also got flashed successfully but the problem I think is I forgot to flash Lazy Flasher due to which the phone booted but was lock even though i entered the right password It started to reset the phone. Then the phone turned off never revived from there.
As I tried to power up many times and tried almost all the combination Keys like Power+Vol up,Power+Vol down,Power+Vol up+Vol Down,etc.Only Red Light is blinking while connected to charging or PC. In PC the Port shows Qualcomm 900E and cannot be recognized in Mi Flash Tool. As Mi flash tool detects Qualcomm 9008.Even I manually Tried to change the driver to 9008 but didn't help me to flash the ROM.Shown an error: Device attached is not working; in Mi Flash Tool
Even I showed in a repair center near me but he ended up with no solution even. I have been trying to get it in Edl mode so that i can flash Fast boot Rom but no clue for that.
If any clue for this would be really appreciated!!!
Your Believer
R$(Rishabh Sharma)
Thinker Hour =)
Here you go:
https://forum.xda-developers.com/re...mi-note-3-pro-special-edition-mm-rom-t3453470
Say if it was working
Useless Thread Dude
Maximaro said:
Thinker Hour =)
Here you go:
https://forum.xda-developers.com/re...mi-note-3-pro-special-edition-mm-rom-t3453470
Say if it was working
Click to expand...
Click to collapse
As I mentioned all the problem in the thread....there's nothing wrong with bootloader.
Thanks but no thanks
More info required: Official unlock or Unofficial unlock?
After flashing oreo ROM lazy flasher is not required you need to format data ( apart from wiping data ) to boot the device.
when connected to PC when the red light is blinking that means you're in EDL mode, now try holding power + vol down button, keep holding until you get a vibration & get into fastboot mode.
Then you can use fastboot commands to check if the bootloader is still unlocked & can flash TWRP again if erased.
But, if device is unable to enter fastboot mode then you must flash MIUI fastboot ROM through EDL.
The procedure is the same for flashing but you need appropriate drivers en.miui.com/forum.php?mod=attachment&aid=NzU4MzF8ZWU0ZWM1OTR8MTM5ODc1NDUzM3w2NDg1MDkzM3wxOTY5Nw%3D%3D
look like EDL mode
I can buy ur phone if u want to sell it. Reply if u r interested.
Unofficial Unlock
VaibhavKumar07 said:
More info required: Official unlock or Unofficial unlock?
After flashing oreo ROM lazy flasher is not required you need to format data ( apart from wiping data ) to boot the device.
when connected to PC when the red light is blinking that means you're in EDL mode, now try holding power + vol down button, keep holding until you get a vibration & get into fastboot mode.
Then you can use fastboot commands to check if the bootloader is still unlocked & can flash TWRP again if erased.
But, if device is unable to enter fastboot mode then you must flash MIUI fastboot ROM through EDL.
The procedure is the same for flashing but you need appropriate drivers
I have tried holding all the combination keys as mentioned earlier but no results. So without getting in Fastboot mode i cannot flash the rom and I don't think so that my device is in EDL mode because PC device manager shows Qualcomm 900E instead of 9008.
Thanks for replying to the thread and please provide other solution.
Click to expand...
Click to collapse
OK
forever.parv said:
I can buy ur phone if u want to sell it. Reply if u r interested.
Click to expand...
Click to collapse
ok
Hello,
Is there a solution to this problem? I too have the exact issue now.
Thanks
Rahim.
I am ready to buy the phone + also can help you solve the issue.. which one do you want
Test Point Method
bro just go for test point method, it works for me
for that use have open backcover of your phone
Solution please
evansourav said:
I am ready to buy the phone + also can help you solve the issue.. which one do you want
Click to expand...
Click to collapse
It would be great if u provide a solution for this.
Rishabh Sharma_10 said:
It would be great if u provide a solution for this.
Click to expand...
Click to collapse
Can you turn off the device?
Yudhz® said:
look like EDL mode
Click to expand...
Click to collapse
Yeah his phone in EDL mode. I went through this problem. Now everything is working fine.
---------- Post added at 05:19 PM ---------- Previous post was at 05:15 PM ----------
You're already in EDL mode. So start from edl part. Try this... http://en.miui.com/thread-235865-1-1.html
evansourav said:
Can you turn off the device?
Click to expand...
Click to collapse
The device is already dead.
What happens when you plug charger? What about Qualcomm QHSUSB BULK? Is it showing up in EDL? Vibration Works? LCD Backlight Turns On?
santoshbodake said:
bro just go for test point method, it works for me
for that use have open backcover of your phone
Click to expand...
Click to collapse
Once happened to me this method worked for me
same issue here have you got any solution
This happens to me once...but i got it solved. This is really an edl mode of the phone. Keep trying connecting it to pc and try pressing those volume and power buttons if there is any voice connecting to pc means your phone is not dead. So, keep trying.
https://forum.xda-developers.com/redmi-note-3/how-to/unlock-unofficially-install-zcx-twrp-t3586778
Here, this helped me. If you follow the instructions correctly, you will be able to unlock bootloader, boot into twrp and then flash your custom rom. Skip to the part when you will have the red led blinking.
Hope it helps.
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
EFAYSAL said:
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
Click to expand...
Click to collapse
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
SubwayChamp said:
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
Click to expand...
Click to collapse
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
EFAYSAL said:
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
Click to expand...
Click to collapse
Ok, I guess that your device is actually in bootloop and don´t booting.
Tutorial that you followed has many steps and don´t need to do all this to just root device and it contains some files like lk.bin that you can´t be sure that should be for your device.
Some users use this file (lk.bin) of an unlocked device and think that flashng in other device then get unlock it but no need, your device can be unlock it just follow some commands in fastboot mode.
Now you can do the next;
Try to flash again your rom stock (I guess that you don´t have a backup), if for some reason your official tool doesn´t work then use only some images like boot, system and userdata with the scatter.txt to flash them through SP Flash Tool.
Here a link to TWRP https://youtu.be/6vj_BY6xJdA, you can root it with supersu v2.78 0r v2.82 and here some files that can be usefull too https://drive.google.com/uc?id=0BwJgeCYTpnEHNlg2VUlieHFTYVU&export=download
Update steps that you are following to can assist. What extension has your rom and if it is recogniced for SP Flash Tool. I didn´t ask you if you can enter to fastboot mode and if you can then you can know if your bootloader is unlocked typing fastboot oem info
Most info that you give and some screenie will help to understand better
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
EFAYSAL said:
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
Click to expand...
Click to collapse
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
SubwayChamp said:
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
Click to expand...
Click to collapse
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
EFAYSAL said:
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
Click to expand...
Click to collapse
I´m not sure if you are connecting correctly your device at right time and form to can flash it properly. Every device has more or less a specific way to do it. My last alcatel it was connected just with device power off and after to tap on download, but in other device Blu Dash was connected pressing just vol_up and my last mt6757 Bluboo had to press both vol up and down at time to connect to pc and after to tap on download option. To have sure that is well done increase volume in your pc, you will hear a first sound that is cause pc is recognicing but then you have to hear a second sound that is when SPFlashTool is recognicing device and you will see a red line in down side of the tool window, release button inmediately and let tool to work.
This is a good rom for your device according the author is optimized https://droid1311.blogspot.com/2017/08/alcatel-fl02-aka-flash-plus-2-via.html and this is the link directly if you have troubles with pop-up-adds https://drive.google.com/file/d/0BwAGh1drb91SeDZwV1VXbXpjQWM/view
Also you can try with other versions of SP Flash Tool, most stable maybe should be v5,1628 https://androidmtk.com/smart-phone-flash-tool leth me know how you go
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
SPFlashTool 5.1628:
I try all the way with and without pressing any button but no luck . And when it work finishing with error.
SPFlashTool 5.1628:
I try all the way to get that mode but nothing works. So I try to click download button then conect the phone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
EFAYSAL said:
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
I try all the way to get that mode but nothing works. So I try to click download button then conect the pkone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
Click to expand...
Click to collapse
There is a part that is not variable in the way to use this tool, ever you have to tap on download before to connect device and is recommendable too connect cable usb to pc (not yet to device); from here is when the button that you have to press can vary but like I said you before in my last mt6757 (a very similar to yours) works pressing both vol at same time to connect terminal cable to device and now you will see a red line (could be violet-ish)
Try before just flashing only preloader file to recreate some partitions and then do other flash for the other files.
Of course you have to be sure that all drivers are installed correctly cause this tool needs to put your device in download mode (a special level) and also keep it in this state so find VCOM drivers for Alcatel and adb/fastboot installer and try to uninstalling some older drivers that you don´t use and many times we keep in our pcs and for a short data transmission can helo that all the rom move it in same folder where SPFlashTool is allocated.
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
EFAYSAL said:
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
Click to expand...
Click to collapse
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
- In what android version are you, 6.0?
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
- Did you try to flash just preloader, only this file?
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
SubwayChamp said:
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
Click to expand...
Click to collapse
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
SubwayChamp said:
- In what android version are you, 6.0?
Click to expand...
Click to collapse
Yes, last time it was 6.0 before the root
SubwayChamp said:
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
Click to expand...
Click to collapse
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
SubwayChamp said:
- Did you try to flash just preloader, only this file?
Click to expand...
Click to collapse
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
SubwayChamp said:
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
Click to expand...
Click to collapse
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
EFAYSAL said:
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
Yes, last time it was 6.0 before the root
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
Click to expand...
Click to collapse
You need to try two different ways to flash files and restore your device.
First method: fastboot mode
You need to get device enter to fastboot in order to flash some files like system, boot and userdata, then there are two main methods to do it:
- Pressing pwr + vol down
- And I mentioned that sometimes work pressing both volume button + pwr and a menu have to appear to can select an option to enter to (fastboot mode), in some devices this method is not working but you have to try several times attempting to.
Second method: SPFlashTool
You have to ever press first of all Download box and connect terminal cable to pc and the buttons thhat you need to press at time to connec cable usb to your device may vary, sometimes vol down, sometimes both vol but never pwr button; if pc recognice then you have to release all buttone an let it pc continue the flash process.
If SPFlashTool recognice device first flash only preloader file and select now lk.bin too. Flash only these two files and after do again a new flash with the rest of the files, Why you need to do this? your partitions are corrupted and you need to restore them with these files in order to can flash all another files.
Before all of this charge your battery, if you have a cover removable then extract it some minutes and put it again.
Also I read that for this model it´s used this tool instead of SPFlash Tool https://androidmtk.com/download-sugar-mtk-sp-flash-tool (inside the zip you will find a password to start the tool) but I´m not sure what kind of rom it needs, you have to connect your device to begin the process, you will find in product models section in the tool this variant for your device "FL02"
Try first the other tool and then this and let me know how you go, mtk devices are almost unbrickeable so it´s just to find the appropriate way to return it to the life.
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
EFAYSAL said:
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
Click to expand...
Click to collapse
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
I understand that you tried with Sugar tool with no lucky.
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Is there some custom development, recovery, roms for your device?
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
SubwayChamp said:
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
Click to expand...
Click to collapse
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
SubwayChamp said:
I understand that you tried with Sugar tool with no lucky.
Click to expand...
Click to collapse
Yes. After recognizing it keeps trying to download data but no luck.
SubwayChamp said:
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Click to expand...
Click to collapse
I know it is disappointing!. I try this but no luck.
SubwayChamp said:
Is there some custom development, recovery, roms for your device?
Click to expand...
Click to collapse
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
SubwayChamp said:
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
Click to expand...
Click to collapse
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
EFAYSAL said:
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
Yes. After recognizing it keeps trying to download data but no luck.
I know it is disappointing!. I try this but no luck.
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
Click to expand...
Click to collapse
I´ll tell you some ideas with no any specific order that you can try or see if works.
Really very strange that display stays in black, you told me that flashing files through fastboot is working but doesn´t appear not even bootlogo, connect to pc as it is and see how pc recognices in devices manager and my pc if appears like a determined drive d/e/f so it looks that some bad flashing burn your kernel and this case is similar to when a Samsung device need to use jtag method to revive, if in your country no-one knows about Alcatel devices this could be a similar case to what I´m saying then it could be a clue for a technician. I tell you this cause many time ago when I flashed by error a Samsung s4 and only this method revived my device.
Try this, flash your stock recovery only through SPFlash tool and flash after through Alcatel Download tool your stock rom cause some firmwares need to detect stock recovery first to can flash other partitions.
At this stage don´t you have stock recovery, no? so you can try to format data cause sometimes when bootloader is altered then avoid to boot and formatting data can solve this.
If this recovery twrp is for your device you can try flashing through SPFlash tool, you have to put recovery.img and scatter-txt in a same folder. then if succesfull format data, system, wipe cache and dalvik and maybe later try to port some custom rom would be a way to solve this.
To flash any partition through fastboot this is the syntax, just follow one by one any of the files that are in your rom folder so just follow these, if some of then can´t be flashed don´t worry then it´s not flashable:
fastboot flash boot bot.img
fastboot flash cache cache.img
fastboot flash lk lk.bin
and so on till the end
...But after try this if you didn´t get boot to recovery and obviously you can´t delete data nor system then delete first the next partitions trough fastboot typing:
fastboot erase system
fastboot erase cache
fastboot erase userdata
fastboot erase boot
Try all this and let us see how it goes
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
EFAYSAL said:
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
View attachment 4518365
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
Click to expand...
Click to collapse
I see that Sugar tool detects your device like rooted and refuses to flash anything, compare imei number which is in the box, I hope that it couldn´t be changed.
Don´t tell me simply no luck, what it says in SPFlash tool when you tried to flash TWRP and I guess that you put scatter-txt and twrp renamed recovery.img simply in the same folder. Just to be clear, to can flash with this tool your device it has to be off not needed fastboot for this. (provide some screenie)
Other combination of keys to enter to fastboot to flash some partitions when something is missing is, try these three ways:
- Pressing only vol down and at same time connecting to charger (connect first one terminal of cable to your device and then to the charger)
- Pressing the three buttons till a menu appears (you must to release inmediately all)
- Pressing vol up + pwr till a menu appears (you must to release pwr button inmediately) then choose fastboot
In the post 4 I provided a link from Google Drive, in this zip there are 8 items;
- From the item 2 use this version of SP Flash tool, put the four files in a folder and flash them
- In the item 3 you will find some scripts for fastboot, maybe they´re working better and also you have here a subfolder with twrp image.
- And if you get sucessfully install twrp in the item 7 there is a backup with some files to restore from this recovery.
Try one by one and update the info, I hope that your motherboard is not damaged.
WARNING, THIS GUIDE WILL WIPE ALL THE DATA IN YOUR DEVICE.
!!! Whatever you do, it is at your own risk !!!
This procedure will unbrick any Axon 7, returning it to stock. It fixes any kind of brick as long as your hardware is not damaged. You can't damage your hardware using software so if you have a healthy unit, you can recover it from any flashing "accident".
1. GET THE SOFTWARE
You need a Windows PC, Windows 10 is highly recommended. Do this:
01. Install MiFlash in your PC. It includes the Qualcomm Snapdragon SoC drivers, nonetheless you can always install the latest drivers.
02. Download the EDL flashable stock firmware package for your model:
A2017 (China): B14_MIFAVOR5 Android: 7.1.1
A2017G (Europe): B10_NOUGAT Android: 7.1.1
A2017U (Americas): B35_NOUGAT Android: 7.1.1
03. Unzip the firmware ZIP file to a folder in your hard drive.
2. ENTER EDL MODE
Option A: USING THE REBOOT COMMAND
If you still have access to your system but not to recovery or fastboot, then you just need to install any terminal app, open it and at the app's command prompt enter:
Code:
reboot edl
. You device will reboot into EDL mode. Now you can safely plug your Device to your computer. In your computer right click in the Windows Start Menu icon and select Device Manager. Under Ports (COM & LPT) your device should appear as Qualcomm HS-USB QDLoader 9008 using a virtual COM port. If you can see it, then you can continue to the flash section, step 14. Otherwise, if you do not see anything or a DFU device, then you'll need to explore the next option.
Option B: USING THE BUTTON COMBO
04. Press the VolUp and VolDn buttons in your device and keep them pressed.
05. Now press the power button until the red LED flashes, it does it really quick. Then release the buttons, starting by the power button.
06. Plug the device to your computer.
In your computer right click in the Windows Start Menu icon and select Device Manager. Under Ports (COM & LPT) your device should appear as Qualcomm HS-USB QDLoader 9008 using a virtual COM port. If you can see it, then you can continue to the flash section, step 14. Otherwise, if you do not see anything or a DFU device, then you need an EDL cable.
OPTION C: USING THE EDL CABLE
So, you need to get a Qualcomm EDL cable. With it you can recover from any situation. I use this one, DrakenFX uses this other model. There are cables out there not working properly so do not try to save 4 or 5 bucks and get yours from a reliable source. Alternatively you can solder your own by following this guide. If you are in an emergency (or your patience threshold is very low) and have a thin wire around you, then you can follow this DIY hack video.
Do you already have the EDL cable? then follow these steps:
07. Connect your bricked Axon 7 to your PC using the EDL cable.
08. Press the EDL cable button and keep it pressed.
09. Press the Power button of your bricked unit and keep it pressed too.
10. Wait 20 seconds.
11. Release the power button.
12. Wait 10 seconds.
13. Release the button of the EDL cable.
Voilà, your device is now in EDL mode. The device manager in your PC, under the ports category, should detect it as Qualcomm HS-USB QDLoader 9008. Now you can proceed to the flash section. If this procedure doesn't work, then your unit could have a hardware problem. Your only hope is to dissemble it by following this last resort guide.
3. FLASH FIRMWARE
14. Open MiFlash in your computer.
15. Click Browse button and select the folder you created in step 03 with the stock firmware files.
16. Click Refresh button and your device will appear listed as virtual COM port.
17. Click Flash button and wait for a few minutes until it finishes. Note that the bottom options are not applicable.
18. Now you have a stock Axon 7. Your data partition will still have garbage data, so you should enter recovery by pressing VolUp while rebooting your device with the power button. Release VolUp only when you reach Recovery. Using Recovery do a Factory Reset of your device.
That was the last step. Hopefully now you have a fully functional stock Axon 7.
By the way, this guide can also be used to return to stock any working device for selling or service!!!!
Cheers!!!!
Nice! I just disassembled mine and did it that way the other day.
thank you.
i will save the files and guide for rainy day.
i have A2017 that i converted into A2017U; which file do i need to download?
@Oki
Thnx for this guide :good:
Find the latest A2017G N-B10 here
Harmtan2 said:
Nice! I just disassembled mine and did it that way the other day.
Click to expand...
Click to collapse
Glad to see you solved your issue.
mb0 said:
thank you.
i will save the files and guide for rainy day.
i have A2017 that i converted into A2017U; which file do i need to download?
Click to expand...
Click to collapse
I don't know what you mean about converting an A2017 into an A2017U. They are the same device except for the radio, that that's a hardware difference. You should always use the right modem firmware for your radio hardware so you should use the A2017 modem firmware. After unbricking your unit, you can unlock it again and flash any universal firmware the same way you did before. It is a long but safe process.
yes, i meant to say that i flashed U radio over my A2017
so China version is for me.
mb0 said:
yes, i meant to say that i flashed U radio over my A2017
so China version is for me.
Click to expand...
Click to collapse
If you flashed the A2017U radio in a A2017 hardware and worked fine for you, then you can use the A2017U B35 stock firmware.
What will be the bootloader status after following this guide? I need my phone with a locked bootloader.
My phone shows up as Handset Diagnostic Interface (DFU) (COM3) but it doesn't get detected on Miflash program......
aLexzkter said:
What will be the bootloader status after following this guide? I need my phone with a locked bootloader.
Click to expand...
Click to collapse
It should be locked. But in case you end up with an unlocked phone, then locking it is very easy. You only need to connect your phone, enter into fastboot mode, download the adb/fastboot tools and execute the command fastboot oem lock from your computer.
Oki said:
It should be locked. But in case you end up with an unlocked phone, then locking it is very easy. You only need to connect your phone, enter into fastboot mode, download the adb/fastboot tools and execute the command fastboot oem lock from your computer.
Click to expand...
Click to collapse
I can't get into EDL mode. I hold down volume buttons, then power. When the red led lights up, I unpress power, then the volume buttons, connect the USB cable and nothing happens on my phone (black display) red led still on. On my computer I see ZTE Handset Diagnostic Interface(DFU) (COM3).
Edit: I managed to get into EDL mode thanks to Axon 7 EDL Tool but I got a "File analysis: error" "not important files found" so I went back to MiFlash and also got an error about the files. Will update the post when I get it to work.
aLexzkter said:
I can't get into EDL mode. I hold down volume buttons, then power. When the red led lights up, I unpress power, then the volume buttons, connect the USB cable and nothing happens on my phone (black display) red led still on. On my computer I see ZTE Handset Diagnostic Interface(DFU) (COM3)
Click to expand...
Click to collapse
You can enter EDL mode from the system. Just install any terminal app, open it and enter the command reboot edl
Oki said:
You can enter EDL mode from the system. Just install any terminal app, open it and enter the command reboot edl
Click to expand...
Click to collapse
xD My phone was bricked. I thought this tutorial was mainly targeted for bricked devices.
Anyway, my phone is working now. The downloaded EDL zip was corrupt so it only had a few files inside.
@Oki
Edit: I have a working phone on Nougat B10. But I can't lock the bootloader because I don't have access to fastboot. My phone's variant is A2017G
aLexzkter said:
xD My phone was bricked. I thought this tutorial was mainly targeted for bricked devices.
Anyway, my phone is working now. The downloaded EDL zip was corrupt so it only had a few files inside.
@Oki
Edit: I have a working phone on Nougat B10. But I can't lock the bootloader because I don't have access to fastboot. My phone's variant is A2017G
Click to expand...
Click to collapse
Glad to see you solved your issue. I misunderstood your problem. I thought you had access to the system and not to recovery or fastboot. Anyway, this guide is for unbrick or return to stock. I'll investigate the relock problem. Usually clearing devinfo partition should be enough to relock any bootloader.
Oki said:
Glad to see you solved your issue. I misunderstood your problem. I thought you had access to the system and not to recovery or fastboot. Anyway, this guide is for unbrick or return to stock. I'll investigate the relock problem. Usually clearing devinfo partition should be enough to relock any bootloader.
Click to expand...
Click to collapse
In order to get access to fastboot I had to use the tool Axon7Toolkit, select "unlock bootloader" option, make sure you have an old version of MiFlash installed (20161212) and then you can select "lock bootloader" on Axon7Toolkit.
Thanks for everything.
aLexzkter said:
In order to get access to fastboot I had to use the tool Axon7Toolkit, select "unlock bootloader" option, make sure you have an old version of MiFlash installed (20161212) and then you can select "lock bootloader" on Axon7Toolkit.
Thanks for everything.
Click to expand...
Click to collapse
Well, I am considering to link the older Marshmallow ROMs since the Nougat ROMs have some issues with fastboot. Anyway. It is going to take some time to test the alternatives. Thanks for letting us know!
Some of the most recent firmware for Axon 7 (@NFound's B12 bootstack, I think) doesn't support the EDL button combo. But if you have TWRP installed, you can boot to recovery, then reboot to EDL from there.
I kept getting the device registering in device manager in DFU mode. But I noticed that it briefly registers as QUSB_BULK before reverting to DFU. So I installed zadig winUSB driver and now it registers as QUSB_BULK when I turn on the device pressing all 3 buttons.
How can I proceed now?
Hi there
Thanks for this guide. I have a 2017U, so I got A2017U_B35_NOUGAT_FULL_EDL.zip file. After unzipping and connecting the phone to the computer it gets properly recognized and i can start the process from the MiFlash program. After reaching somewhere between 30-40% of the flashing process, it goes suddenly to 100% and it says that is finished. When I reboot the phone, it appears as if I was still under an unlocked bootloader (warning message + TUX penguin image) and the phone starts but during the initial setup process, i chose to start as a new phone but it says that "This device was reset. To continue, sign in with a Google Account that was previously synced on this device" and obviously this is not what I am interested for.
How can I get rid of this message and get a full clean install, with bootloader relocked and all that??
Thank you for any help you can provide!
Flogisto said:
Hi there
Thanks for this guide. I have a 2017U, so I got A2017U_B35_NOUGAT_FULL_EDL.zip file. After unzipping and connecting the phone to the computer it gets properly recognized and i can start the process from the MiFlash program. After reaching somewhere between 30-40% of the flashing process, it goes suddenly to 100% and it says that is finished. When I reboot the phone, it appears as if I was still under an unlocked bootloader (warning message + TUX penguin image) and the phone starts but during the initial setup process, i chose to start as a new phone but it says that "This device was reset. To continue, sign in with a Google Account that was previously synced on this device" and obviously this is not what I am interested for.
How can I get rid of this message and get a full clean install, with bootloader relocked and all that??
Thank you for any help you can provide!
Click to expand...
Click to collapse
There ate several ways to remove that. One involves TWRP 3.2.1-7 and the other Axon 7 EDL tool, if you dont have TWRP then use the second . Jusy go to the unlock menu and apply the google unlock.
A third way would be to setup the phone with your old google account and do afactory reset from within Android, not from the bootloader. That would remove also the owner safety.
Thank you so much for your guide and software bundle.
I even had to make a EDL cable to restore my device.
After flashing, I do not see vendor as a partition but looks like it is a folder. Is it OK for future ROMs ?