Galaxy S6 Edge SM-G925F bricked - Galaxy S6 Edge Q&A, Help & Troubleshooting

Hello, my phone recently powered off by itself and when I powered it back on again it was stuck on the flashing Samsung logo. When I try to flash the stock firmware in odin it fails and I get the log below, help!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

debuffs said:
Hello, my phone recently powered off by itself and when I powered it back on again it was stuck on the flashing Samsung logo. When I try to flash the stock firmware in odin it fails and I get the log below, help!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
You are flashing an older bootloader. That's why odin fails at sboot.bin.
You need to flash the latest firmware and it will work.

Related

GalaxyS2 I9100G odin flash FAIL!

I was flashing a firmware from "I9100GZCKH4" to "I9100GDXLP6_I9100GOLBLP6_XME" on my Samsung S II GT-I9100G, and it failed. Now the screen shows "SOFTWARE UPDATE FAIL"
Odin says...
Message
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GDXLP6_I9100GOLBLP6_I9100GDXLP6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.img
<ID:0/005> NAND Write Start!!
<ID:0/005> factoryfs.img
<ID:0/005> hidden.img
<ID:0/005> MLO
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Happen to me once..make sure KIES not running in background..if u dont know how to check, just uninstall KIES..dont worry, u can get KIES installer later with just google it..
Sent from my GT-I9100G using xda premium

***URGENT HELP*** Write failure to stock rom

Hello all,
I rooted my galaxy s3 and all went fine, then the battery died (battery is no longer in use) so i bought a new one and all was well, upon flashing stock rom, the write failed.
When booting the phone up it says: "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
(LONG DELAY HERE)
<OSM> I9305XXBLL5_I9305EVRBLL2_I9305BVBLL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas? I need help!
Bad flash wrong firmware or more likely file is corrupt .
Make sure Kies is not running as well .
jje

[Q] Problem with Odin (SM-T230NU)

Greetings!
I downloaded the GALAXY Tab 4 7.0 firmware for Slovakia and I am trying to put it to my SM-T230NU with Odin. No SD card in device, rooted.
When I click start on Odin:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230XXU0ANE6_T230OXX0ANE2_T230XXU0ANE6_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> timh.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
How can I solve this problem? Thanks a lot!

NAND Write Fail Error Message...Please Suggest how to overcome and Fix !!!!

I've Samsung Galaxy S3 (GT-I9300T) purchased from Australia-Telstra.
The phone is stuck at Samsung Boot Up logo and is unable to proceed further.
However i've downloaded all the firmware versions from the below mentioned location:
.sammobilecom/firmwares/d...GT-I9300T/TEL/[/url]
2014-04-01_Australia_(Telstra)_4.3_I9300TDUUGNC1_I9300TTEL GNC1_YES
2013-11-01_Australia_(Telstra)_4.1.2_I9300TDUEMJ1_I9300TTE LEMJ2 YES
2013-01-01_Australia_(Telstra)_I9300TDUELL2_I9300TTELELL2_ YES
2012-11-01_Australia_(Telstra)_I9300TDUDLK2_I9300TTELDLK2_ YES
2012-08-01_Australia_(Telstra)_I9300TDUBLH1_I9300TTELBLH1_ YES
After using the Odin3 i get the error message mentioned below (NAND WRITE START....FAIL):
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUUGNC1_I9300TTELGNC1_I9300TDUUGNA2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Desprado_14 said:
I've Samsung Galaxy S3 (GT-I9300T) purchased from Australia-Telstra.
The phone is stuck at Samsung Boot Up logo and is unable to proceed further.
However i've downloaded all the firmware versions from the below mentioned location:
.sammobilecom/firmwares/d...GT-I9300T/TEL/[/url]
2014-04-01_Australia_(Telstra)_4.3_I9300TDUUGNC1_I9300TTEL GNC1_YES
2013-11-01_Australia_(Telstra)_4.1.2_I9300TDUEMJ1_I9300TTE LEMJ2 YES
2013-01-01_Australia_(Telstra)_I9300TDUELL2_I9300TTELELL2_ YES
2012-11-01_Australia_(Telstra)_I9300TDUDLK2_I9300TTELDLK2_ YES
2012-08-01_Australia_(Telstra)_I9300TDUBLH1_I9300TTELBLH1_ YES
After using the Odin3 i get the error message mentioned below (NAND WRITE START....FAIL):
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUUGNC1_I9300TTELGNC1_I9300TDUUGNA2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Tens of threads on this subject: Search results

Flashing stock ROM for Samsung galaxy s4 gt-i9505 keeps failing with Odin

hello everyone,
I am trying to follow this guide: https://forum.xda-developers.com/showthread.php?t=2265477
I download the stock rom from the links in the documentation itself.
After my first try this is the log:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK9_I9505H3GEMJ2_I9505XXUEMK9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
Fine, the pit is missing, I download it from the guide itself again and add it to the process and toggle on Re-Partition.
Log says:
Code:
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
Nothing more than this.. so I don't know where is failing. Any suggestion? Thanks in advance!

Categories

Resources