Hello everybody. (sorry for my writing mistakes )
XT910 with stock firmware: http://savepic.org/6550017.png
IMEI - EMEA region
Worked fine.
But then...
Through BMM installed - LiquidSmooth KitKat (http://forum.xda-developers.com/showthread.php?t=2782971)
and then
"SPYDERIRD_U.01.6.7.3-94_SPI-328_04.11.01P_0A.74_ASIA_RETAIL_HKTW_CFC_HWp2b_SIGNED.xml.zip"
(I do not know why. It was not me. But I want to help restore the phone.)
When the process is finished (Successfully О_о), the phone no longer worked.
Now:
Normally mode, Recovery - not working:
Invalid Flash Mode (S) (Boot Failure)
0A.77
To return to normal mode - first press power key to poser down
Device is LOCKED. Status Code: 0
Battery OK
OK to Program
Connect USB
Data Cable
Invalid CG OTV (CG: system): Invalid SP Data
Invalid CG HAB (CG: system, status: 0X004E)
Invalid CG OTV (CG: system)
What we tried to install (AP Fastboot - RSDLite 6.1.5):
- SPYDERIRD_U.01.6.7.3-94_SPI-328_04.11.01P_0A.74_AUSTRALIA_NZ_CFC_HWp2b_SIGNED.xml.zip
- SPYDERIRD_U.01.6.7.3-94_SPI-328_04.11.01P_0A.74_AUSTRALIA_OPTUS_CFC_HWp2b_SIGNED.xml.zip
- SPYDERIRD_U.01.6.7.3-94_SPI-328_04.11.01P_0A.74_MEA_RETAIL_CFC_HWp2b_SIGNED.xml.zip
- SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSO2DE_HWp2b_Service1FF_fastboot.xml.zip
- SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_Service1FF_fastboot.xml.zip
- 673.94.324.XT910.AsiaRetail.en.03.xml.
- 9.8.2O-124_SPUEM-14_S7_USASPDRICS01RTFE1007.0R_USASPDRJBRTFR_P013_A014_p2b_S1FF_fb_CFC.xml.zip (Retail FR)
- 9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml.zip (Retail GB)
Always:
11/28/14 11:48:56 [Device ID: 0] 1/19 flash mbm "allow-mbmloader-flashing-mbm.bin"
11/28/14 11:48:56 [Device ID: 0] 2/19 reboot-bootloader
11/28/14 11:49:00 [Device ID: 0] 3/19 flash mbmloader "mbmloader.bin"
11/28/14 11:49:01 [Device ID: 0] 4/19 flash mbm "mbm.bin"
11/28/14 11:49:02 [Device ID: 0] 5/19 reboot-bootloader
11/28/14 11:49:06 [Device ID: 0] 6/19 flash cdt.bin "cdt.bin_signed"
11/28/14 11:49:06 ERROR: 6/19 flash cdt.bin "cdt.bin_signed" -> Phone returned FAIL. - on device ID 0.
11/28/14 11:49:06 [Device ID: 0] 6/19 flash cdt.bin "cdt.bin_signed" -> Phone returned FAIL.
11/28/14 11:49:06 ERROR: Failed flashing process. - on device ID 0.
This metod:
1-download cdt.bin ( http://www.mediafire.com/?ua1nj6ds6r0vtue )
2-download fastboot files ( http://dfiles.eu/files/bih3tmg7b )
3-restart your phone in to bootloader ( fastboot ) mode
4-connect your phone via usb cable
5-open cmd.exe in your pc an go to fastboot files
6-flash cdt.bin via this command -------------------------------------- fastboot flash cdt.bin cdt.bin
7-restart your phone in to stock recovery
8-do triple wipe and restart your phone
Nothing helps! Can you help? What can we do?
Thanks for help...
No one has any ideas?
that's interesting: tried to remove CID and failed, because: (see picture)
Code:
Erasing CID ... INFOCommand Restricted
Wrong command?
And:
Code:
CID:5
XT910S ?
Why can not we delete CID?
Thanks for "help".
Mission completed.
Thread is closed.
did u manage to fix your i have the same problem with you please some one should help,i just want to get my phone back to normal, i have the same firmware with u
jamil1982 said:
did u manage to fix your i have the same problem with you please some one should help,i just want to get my phone back to normal, i have the same firmware with u
Click to expand...
Click to collapse
This is my script for FastBoot (0A:77 Bootloader and for XT910S)
Warning! This will remove your CID!
Use this method only when all other methods have failed.
https :// yadi .sk/d/M2EmR9HKdA3pF
unpack RAR: in C:/MyRecover/
Connect your phone (AP Fastboot mode) to PC.
Run MyRecoverV1.bat
done.
After that, you can install any firmware (RSDLite 6.1.5)
reccomend: Britain Retail 4.1.2 : https :// yadi .sk/d/zcq12jT5d44mu
After finish all task whitout errors, reboot cellphone, press Volume up, volume down and Power, and selet "BP Tools"
Get Root
Install BMM 0.3.4
Now your phone loaded automatically (without BP TOOLS)
VasyaAgPro said:
This is my script for FastBoot (0A:77 Bootloader and for XT910S)
Warning! This will remove your CID!
Use this method only when all other methods have failed.
https :// yadi .sk/d/M2EmR9HKdA3pF
unpack RAR: in C:/MyRecover/
Connect your phone (AP Fastboot mode) to PC.
Run MyRecoverV1.bat
done.
After that, you can install any firmware (RSDLite 6.1.5)
reccomend: Britain Retail 4.1.2 : https :// yadi .sk/d/zcq12jT5d44mu
After finish all task whitout errors, reboot cellphone, press Volume up, volume down and Power, and selet "BP Tools"
Get Root
Install BMM 0.3.4
Now your phone loaded automatically (without BP TOOLS)
Click to expand...
Click to collapse
Downloading Right now thank You i will give u feed back:good:
after running my MyRecoverV1.bat see what i got
---------------------------------------------------------------
Delete CID for kwyjibo jr by Vasya
---------------------------------------------------------------
Press any key to continue . . .
---------------------------------------------------------------
getvar:all FAILED (remote: unsupported command)
finished. total time: 0.008s
getvar:all FAILED (remote: unsupported command)
---------------------------------------------------------------
0A3BEC240400A007 fastboot
0A3BEC240400A007 fastboot
CID delete:
erasing 'cid'... INFOCommand restricted
FAILED (remote: )
erasing 'cid'... INFOCommand restricted
FAILED (remote: )
finished. total time: 0.010s
sending 'mbm' (512 KB)... OKAY [ 0.089s]
writing 'mbm'... OKAY [ 0.486s]
sending 'mbm' (512 KB)... OKAY [ 0.089s]
writing 'mbm'... OKAY [ 0.507s]
finished. total time: 0.596s
rebooting into bootloader... OKAY [ 0.007s]
finished. total time: 0.008s
< waiting for device >
erasing 'cid'... INFOCommand restricted
FAILED (remote: )
finished. total time: 0.011s
rebooting into bootloader... OKAY [ 0.008s]
finished. total time: 0.009s
< waiting for device >
sending 'mbm' (512 KB)... OKAY [ 0.102s]
writing 'mbm'... OKAY [ 0.489s]
sending 'mbm' (512 KB)... OKAY [ 0.103s]
writing 'mbm'... OKAY [ 0.483s]
erasing 'cid'... INFOCommand restricted
FAILED (remote: )
erasing 'cid'... INFOCommand restricted
FAILED (remote: )
finished. total time: 0.010s
rebooting into bootloader... OKAY [ 0.007s]
< waiting for device >
sending 'mbm' (512 KB)... OKAY [ 0.102s]
writing 'mbm'... OKAY [ 0.488s]
finished. total time: 0.592s
sending 'mbm' (512 KB)... OKAY [ 0.090s]
writing 'mbm'... OKAY [ 0.508s]
finished. total time: 0.599s
erasing 'cid'... INFOCommand restricted
FAILED (remote: )
erasing 'cid'... INFOCommand restricted
FAILED (remote: )
finished. total time: 0.010s
rebooting into bootloader... OKAY [ 0.006s]
finished. total time: 0.007s
< waiting for device >
cid: 5
finished. total time: 0.018s
Press any key to continue . . .
any help please?
this is what my phone is showing
jamil1982 said:
this is what my phone is showing
Click to expand...
Click to collapse
CID not erased, for 0A:74 BootLoader try to use:
http://forum.xda-developers.com/showthread.php?t=2372614
If you want to check, removed CID or not:
Just see on last line in MyRecoverV1:
Code:
< waiting for device >
[COLOR="Red"]cid: 5[/COLOR]
finished. total time: 0.018s
When CID : DEAD - you win
If another thread not helps you:
Run MyRecoverV2 and MyRecoverV3 and again V1
it should help.
VasyaAgPro said:
CID not erased, for 0A:74 BootLoader try to use:
http://forum.xda-developers.com/showthread.php?t=2372614
If you want to check, removed CID or not:
Just see on last line in MyRecoverV1:
Code:
< waiting for device >
[COLOR="Red"]cid: 5[/COLOR]
finished. total time: 0.018s
When CID : DEAD - you win
If another thread not helps you:
Run MyRecoverV2 and MyRecoverV3 and again V1
it should help.
Click to expand...
Click to collapse
thanks i will check the link please can u give me the easy way on how to make a motorola factory cable? i have some factory cables that came with my polar 3 box whenever i connect the cable from my phone to the system the phone show white led light and my system doesnt recognize the phone so i dont know if the phone is charging or not and im afraid of loosing the power battery,but with normal cable my system recognize it but the white led light doesnt show, thank you once again
---------- Post added at 09:14 AM ---------- Previous post was at 08:45 AM ----------
strange i run all the bat but it give me the same
cid: 5
jamil1982 said:
thanks i will check the link please can u give me the easy way on how to make a motorola factory cable? i have some factory cables that came with my polar 3 box whenever i connect the cable from my phone to the system the phone show white led light and my system doesnt recognize the phone so i dont know if the phone is charging or not and im afraid of loosing the power battery,but with normal cable my system recognize it but the white led light doesnt show, thank you once again
Click to expand...
Click to collapse
Only one way for factory cable: (see picture)
jamil1982 said:
strange i run all the bat but it give me the same
cid: 5
Click to expand...
Click to collapse
Now run MyrecoverV2 and V3, then V1 for check.
VasyaAgPro said:
Only one way for factory cable: (see picture)
Now run MyrecoverV2 and V3, then V1 for check.
Click to expand...
Click to collapse
I run the V2 and V3 then Run the V1 again it showed the same thing, but I noticed its like the number has change from 0a.74 to 0A.74 and now its Showing 0A.75
jamil1982 said:
I run the V2 and V3 then Run the V1 again it showed the same thing, but I noticed its like the number has change from 0a.74 to 0A.74 and now its Showing 0A.75
Click to expand...
Click to collapse
hmm...
now - run all .bat files - V1, then 2, then 3 (after 3 NOT run again 1 !)
and finally "info.bat. (https :// yadi .sk/d/HdYWqS1gdAhfr)
Put info.bat to "MyRecovery" dir and run.
Log insert here.
VasyaAgPro said:
hmm...
now - run all .bat files - V1, then 2, then 3 (after 3 NOT run again 1 !)
and finally "info.bat. (https :// yadi .sk/d/HdYWqS1gdAhfr)
Put info.bat to "MyRecovery" dir and run.
Log insert here.
Click to expand...
Click to collapse
OHHH MY G You are Genius :good: after running Myrecover1 again it deleted the cid everything went smooth and the number on my Ap fastboot display 0A.77 then i run this 9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml.zip, it run perfect without any error:laugh: then my phone restart showing Costumer error. Contact Resseller, the i off it and on it to boot menu then select Bp Tools, my phone restart, its time for me to get rid of the Costumer error. Contact Resseller if u can provide me the link i will be very greatfull thanks for everything:good::good::good:
Im rooted using this method http://forum.xda-developers.com/showthread.php?t=2298408 then install BMM Everything went ok only the Costumer error. Contact Resseller but im ok like this thank you so much
xt910 bricked and cant find firmware
Hi,
I also have xt910 razr maxx and i bricked it after installing some kind of custom rom app.
I want to flash stock firmware but all the links on internet are broken. I guess I need this one:
SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_ Service1FF_fastboot.xml.zip
Can aybody help me with a working link of this file pls, its kinda urgent.
Thanks.
VasyaAgPro said:
No one has any ideas?
that's interesting: tried to remove CID and failed, because: (see picture)
Code:
Erasing CID ... INFOCommand Restricted
Wrong command?
And:
Code:
CID:5
XT910S ?
Why can not we delete CID?
Click to expand...
Click to collapse
I have one Moto X 2 , and he it's presenting this problem:
C:\Program Files (x86)\Minimal ADB and Fastboot>mfastboot oem unlock XXXXXXXXXXXXXXXXXXXXX
...
(bootloader) Check 'Enable OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.016s
Yes , I activated USB debugging and also in Rlz Debug " *#*#759#*#* "
Someone could help me ? Thanks!!!
Hi,
I have problem formatting partitions
➜ platform-tools ./fastboot erase system
******** Did you mean to fastboot format this ext4 partition?
erasing 'system'...
ERROR: usb_read failed with status e00002e8
FAILED (status read failed (Invalid argument))
finished. total time: 0.003s
➜ platform-tools ./fastboot erase boot
erasing 'boot'...
ERROR: usb_read failed with status e00002e8
FAILED (status read failed (Invalid argument))
finished. total time: 0.003s
➜ platform-tools
Using ./fastboot format fails similarly.
hrstoyanov said:
Hi,
I have problem formatting partitions
? platform-tools ./fastboot erase system
******** Did you mean to fastboot format this ext4 partition?
erasing 'system'...
ERROR: usb_read failed with status e00002e8
FAILED (status read failed (Invalid argument))
finished. total time: 0.003s
? platform-tools ./fastboot erase boot
erasing 'boot'...
ERROR: usb_read failed with status e00002e8
FAILED (status read failed (Invalid argument))
finished. total time: 0.003s
? platform-tools
Using ./fastboot format fails similarly.
Click to expand...
Click to collapse
The reason I want to format/erase the partitions is because i cannot flash my phone anymore:
./fastboot flash system ~/Downloads/split_updata.pl/kiw_l24_a6.0.1_emui4.0_d003_US/SYSTEM.img
target reported max download size of 266338304 bytes
erasing 'system'...
ERROR: usb_read failed with status e00002e8
FAILED (status read failed (Undefined error: 0))
finished. total time: 0.001s
Also, when I put the phone in fastboot mode I see this:
PHONE Unlocked
FRP Lock
Could that "FRP Lock" be the reason why fastboot does not work, and if so how can I get rid of this FRP Lock?
The FRP Lock appeared after I decided that I had enough with CM13 and wanted to flash back the stock images. The phone is unlocked, but i cannot boot it up unless with fastboot.
About to throw away this phone ... out of ideas...:crying:
I found this for frp lock:
*to remove the factory reset protection (frp) to do this you need to remove all pin/password/fingerprint locks, then remove all google accounts and finally do a factory reset.
Google frp lock xda honor 5x, there are some threads.
Good luck
Sent from my KIW-L21 using XDA-Developers mobile app
rodolphe06 said:
I found this for frp lock:
*to remove the factory reset protection (frp) to do this you need to remove all pin/password/fingerprint locks, then remove all google accounts and finally do a factory reset.
Google frp lock xda honor 5x, there are some threads.
Good luck
Sent from my KIW-L21 using XDA-Developers mobile app
Click to expand...
Click to collapse
I also looked at those, but they are all talking about a fully operational device. The most I can do with my phone is some limited FASTBOOT operations, like:
./fastboot oem get-bootinfo
...
(bootloader) *******************************************
(bootloader) Bootloader Lock State: UNLOCKED
(bootloader) Root State: ROOT
(bootloader) Bootloader WidevineKey: WidevineKey_VALID
(bootloader) System State: Bootloader in UNLOCKED state
(bootloader) Bootloader Version: 001.001.000
(bootloader) *******************************************
OKAY [ 0.011s]
finished. total time: 0.011s
The way it got bricked is, because it is a KIW-UL00 device and I tried to install the US stock rom in it (KIW-L24), like this:
./fastboot flash boot ./kiw_l24_a6.0.1_emui4.0_d003_US/BOOT.img
./fastboot flash system ./kiw_l24_a6.0.1_emui4.0_d003_US/SYSTEM.img
./fastboot flash recovery ./kiw_l24_a6.0.1_emui4.0_d003_US/RECOVERY.img
after that, I tried to reboot the phone and the the restoration of the stock rom did start. However it got to about 5%, then
the phone started rebooting itself and never finished. As a result, I think the FRP Lock appered and I can no longer run the above
commands even though I have the the right stock rom for KIW-UL00.
Any chance to fix that?
Overall the problem I got into this is that no one has tested CM13 or TWRP3 with this particular Honor 5x model, KIW-UL00, which gets people to follow instructions and get their phones bricked. Should have known this before I started ... sigh ...
I have problem when i try unlock bootloader of my ANE-AL00
CMD-Fastboot say: deactivate find my Phone. But isnt prossible.
https://youtu.be/a5CjIqQCbuw
Hi
Hi?
(bootloader) Necessary to disable Phone finder!
FAILED (remote: Command not allowed)
finished. total time: 0.020s
I have been trying to root my device with no luck. I cannot run most fastboot commands
when I run "fastboot getvar all" only one variable is returned
-----------------------------------------------------------------
C:\Windows\system32>fastboot getvar all
all: locked: yes
finished. total time: 0.013s
------------------------------------------------------------------
when I try to unlock, I get the following error
------------------------------------------------------
C:\Windows\system32>fastboot flashing unlock
...
FAILED (remote: Not implemet.)
finished. total time: 0.006s
------------------------------------------------------
Almost all fastboot commands return the above response. I have enabled USB debugging and toggled oem unlocking. I have ran out of options please help. I have even updated my adb_fastboot to the latest release.