I need some help.
My Amazfit bip is dead.
after try to mod .fw + .res file ( update .res file + .fw file all process complete ) "update complete" message show on bip. next step my should be auto restart .
but. after it shutdown. it's not wake up again. T_T
I'm try push button / connect to charger. not happen.
some one have solution to turn it on again.
Or some way to give a factory reset on it? please tell me :crying:
Thank you.
I have the same problem.
After a few minutes of Google I found a instruction from Huami.
1. Wait 36 hours and then press the button 30 seconds
2. If it's don't work charge the amazfit about 20 minutes then try it again
3. Contact the support :/
In this moment I am at point 2
Any news? I have the same problem.
Hello,
i have a bricked Amazfit BIP so i decided to open it up.
I saw there is a Winbond 25Q64FWIQ flash onboard, so i'm wondering if anyone has a flash dump to try to reflash mine with a chip programmer
I have same problem, is there anyone can share how to solve the problem?please
Same problem over here. I already have ordered a new one because I wasn't able to fix the dead one. No solution I was searching for is working for me.
Had the same problem.
Let the watch battery completely run empty ( about 40 days)
Then put it back on charge...
My watch turned back to life
My Amazfit BIP is dead after once I have powered off the watch, not firmware upgrade problem, just normal condition. No water damage and no dropping no scratches. Charge the device still give no result. Any ideas?
***A bricked phone usually can recover by flashing a firmware. BUT BIP watch cannot easily recover using stock firmware because it cannot connect computer using usb.
Jason_20 said:
My Amazfit BIP is dead after once I have powered off the watch, not firmware upgrade problem, just normal condition. No water damage and no dropping no scratches. Charge the device still give no result. Any ideas?
***A bricked phone usually can recover by flashing a firmware. BUT BIP watch cannot easily recover using stock firmware because it cannot connect computer using usb.
Click to expand...
Click to collapse
How are you supposed to flash something that is completely OFF??
Probably it is either frozen or simply died. If there is no way to reset via hardware (press the power on/off button for a long time?), then follow the advice in the post above yours and let the battery go to zero then try to charge it again then turn it on.
lfom said:
How are you supposed to flash something that is completely OFF??
Probably it is either frozen or simply died. If there is no way to reset via hardware (press the power on/off button for a long time?), then follow the advice in the post above yours and let the battery go to zero then try to charge it again then turn it on.
Click to expand...
Click to collapse
I am waiting for my bip battery completely drain out. Maybe two months later and the battery becomes empty.
any news? i have the same problem also. Flashed firmware from 3rd party app and now its dead.
Related
Hi,
I was flashing my i780 with i780_DXHC4_Rev12 and it got stuck at the phone part (after created COM successful), I took the battery out... and try to flash the Phone part again... the phone doesn't turn on at all, (fn+enter+power)... and even I try Power button only... still doesn't work... any help?
kyborg said:
Hi,
I was flashing my i780 with i780_DXHC4_Rev12 and it got stuck at the phone part (after created COM successful), I took the battery out... and try to flash the Phone part again... the phone doesn't turn on at all, (fn+enter+power)... and even I try Power button only... still doesn't work... any help?
Click to expand...
Click to collapse
Try taking the battery off for 24 hours.
then try to light it up...
Nadavi.
1:00AM will wait for 24 hours
kyborg said:
Hi,
I was flashing my i780 with i780_DXHC4_Rev12 and it got stuck at the phone part (after created COM successful), I took the battery out... and try to flash the Phone part again... the phone doesn't turn on at all, (fn+enter+power)... and even I try Power button only... still doesn't work... any help?
Click to expand...
Click to collapse
Mine got stuck at the phone part because I didn't have the 64bit modem drivers for XP at hand .. (only 32bit..) .. yet the phone did turn on, only the phone part wasn't updated. No idea what happened in your case
inertiax3 said:
Mine got stuck at the phone part because I didn't have the 64bit modem drivers for XP at hand .. (only 32bit..) .. yet the phone did turn on, only the phone part wasn't updated. No idea what happened in your case
Click to expand...
Click to collapse
Could you please upload or link me to all the correct modem drivers needed to flash the phone part?
Thanks,
Eran.
search the forum, it 's there
any other tips?
waited for 24 hours :| sill doesn' work
i have same trouble...when i upgrade the phone dead because batrey low..now the phone dead. please same body help....
i got same problem too.
my phone dead because i was upgrade rom with low battery.
please help us. thankyou
amisui said:
i got same problem too.
my phone dead because i was upgrade rom with low battery.
please help us. thankyou
Click to expand...
Click to collapse
This happened to me several times...
Please do the following with a fully charged battery and not USB or charger connected :
toutch the battery contacts fast several times (it creates a small sparkle that you may not see) then press the start button. That should do the trick
come on , can same body help us. !!!!!!! any sofware can flash i780 with dead position? i think the phone dead because not boot+rom+phone instaled. mirage updater only can flash in on condition.
nCoder said:
This happened to me several times...
Please do the following with a fully charged battery and not USB or charger connected :
toutch the battery contacts fast several times (it creates a small sparkle that you may not see) then press the start button. That should do the trick
Click to expand...
Click to collapse
Thank nCoder for your trick, i'll try to night
http://www.youtube.com/watch?v=XJ6l_sSHfec
http://www.youtube.com/watch?v=Fz2II5euldc
I follow you trick lick battery then press start (only start button / shift+enter and start)
but it not happend when i press start button.
what i was wrong?
best regard,
To Upgrade samsung i780
Hi i want samsung i780 firmware OS and it's procedure.
my x10 die suddenly, there was 94% battery left, not plugged out long, few hrs later notice phone was off,and it will not power on again, press power to try to turn it on all it does is vibrate and that's it.
tried to flash stock 2.1 back on but not sure if it did anything, took over night or flash tool to finish, still no boot after that, press power and it vibrates that's all, sometimes it doesn't even vibrate, battery is good, works fine in another x10, put a fully charge battery in it and same result.
anyone know what happened to it?
was running eternity 3a rooted with DT.
I'm going to have to send that in for warranty, hope they won't find anything on it and void the warranty.
Was the phone quite hot at the time or heating up when trying to boot?
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
sharathx10 said:
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
Click to expand...
Click to collapse
That usually does the trick. Unplug battery for 1 minute, reinsert it and try again.
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
do you have a SD card inside. Might be a bad SD card try taking it out and booting it. Happened to me before.
blagus said:
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
Click to expand...
Click to collapse
Hi, just wanted to jump in and ask a few questions about this situation.
Do you always experience this issue? How long before it freezes? What "act" are you doing to prevent freezing? Does the phone work normally afterwards?
Hope you can help me out with some answers, I want to look into this.
instead of starting a new thread,i'll post here..
i have this restart problem..
Before this i try to fix my friend X10.. after many tries and a month acctually,i give up..
Now one more of my friend gave me another X10 which have the same problem..
Problem:
The phone will boot but after several minutes it will auto shut down and when i try to power up no vibrate and stuck at black screen.
when i pull the battery out and on again it vibrate and boot.just after boot animation it will shut down again..
Solution that i have tried so far:
Update with SEUS.
Send to profesional phone service to downgrade to 1.6.
Upgrade/flash with flash tool with GENERIC
Upgrade/flash with flash tool with X10_1.0_SE_StockRom_MultiTouch
Wipe user data in flash tool & x recovery
after several tries i got it work and i root and install x recovery.
Flash from xrecovery with custom rom Eternity.build003a.signed
format memory card.
Change battery.
All the solution i've tried doesn't make the problem dissappear.
anyone have ideas or solution?
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
gonix said:
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Click to expand...
Click to collapse
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Screen-shots are from the old PC Companion, byt they still looks very much like them in the new version
http://forum.xda-developers.com/showpost.php?p=17458289&postcount=8
Emperor.dk said:
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
Click to expand...
Click to collapse
Oh I know someone who has the same x10 with me. I guess Ill have to try your suggestion.
SmG67 said:
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Click to expand...
Click to collapse
It doesnt help because when Im in the part where it says, press the back button while inserting the usb, the phone cannot be detected and so the update cannot continue.
Hi guys,
I was flashing my S10 by Odin, using USB-C connector which is also charging the laptop.. (why didnt use the second one I idiot??)
Odin sudently stoped flashing, stuck maybe on 90% and I was waiting more then hour, but flashing did not succesful, if laptop discharged the battery and switched off.
Samsung is totaly dead, I tried everything like get to recovery mode, Odin mode, leave the battery fully discharged, unplug and replug battery... No any sign of life. PC doesn't see it..
It seems there is nothing I can do for unbrick it, but maybe YOU know some trick that may rescue my phone...?
Is it possible that some box as Octoplus or some like that will be working for my problem?
Many thanks for any idea, Regards, Tomas.
I would recommend trying to return to manufacturing (RMA) the phone just explain that it's hardware bricked doesn't turn on etc and you should get a new phone. How ever if they find out that you tried to flash custom software on your phone your warranty is voided and you might have to buy a new phone.
download official firmware and flash every file except for HOME CSC using Odin. This should revert you back to stock rom and allow you to boot properly.
It's not normal that flashing takes so long in first place.
Something already went wrong while it was still flashing.
My S10 flashes in like 10 minutes completely.
That's strange anyway because mine stopped one or two times flashing
causing a soft brick but I always could enter Download Mode again and reflash.
I'd basically never flash with a notebook not connected to a charger
but in your case I think you could wait even more hours and nothing would happen anymore.
One exception could be that you flashed the wrong firmware.
I wouldn't send it to Samsung if that's the case (in my opinion).
Just don't do such stuff if you don't know what you are doing and learn from it.
A honest option is to aquire a device with broken display and ideally broken back glass and change the motherboard.
It's not that difficult and you could exchange the battery e.g.. (plus it's fun)
Thanks for all answers.
Unfortunately, the rom I flashet was stock and 100% right for my phone. Downloaded from sammobile.
Also now I'm not able to flash anything because PC does not see my phone when connected...not any sound and Odin wont show that device is connected.
One more information-I'm not some fish to do something what I dont know about..my job is technician in mobile phone repair servis and shop. But 99% repairs I'm doing is hardware repair- like broken LCD change, battery change, charging connector repair by soldering... Sometimes software repair of course, I flashed by Odin many many times, but flashing takes max 10 minutes.. this is why used charging port co connect the phone. There was some another problem I'm sure.
Anyway thanks for your answers.
I'll send the bricked phone on eBay, maybe somebody have the right tool to make it done.
Thx again.
NOTHING
You can charge it without it being turned on I assume.
That should get you to 80 or more % so you can repair it with the companion software
glovesave said:
You can charge it without it being turned on I assume.
That should get you to 80 or more % so you can repair it with the companion software
Click to expand...
Click to collapse
Sorry, I do not quite understand how to charge it without being turned on, once connected to the power it will automatically start and restart infinitely, is there any detailed operation method can tell me?
Can you both to recovery and charge there?
Standard way per internet:
"
Recovery Mode SONY Xperia 1 III
At first hold down the Power key for a few seconds to switch off SONY Xperia 1 III.
After that hold down Volume Down and Power button for a couple of seconds.
If the SONY logo appears release the Power key."
In your case see if you can match step 2 up with the phone rebooting if that makes sense.
I would try that with power cable in first, then without the cable in, if the other doesn't work. Then put power in while in recovery mode.
Hope that works
IKIZZN said:
Please help me, my Hong Kong version 512 grey xperia 1 iii arrived on the first day, I tried to brick the Taiwan version of the firmware, and now I am prompted as shown in the picture, and reboot infinitely. I want to use xperia companion to fix it, but it says it needs more than 80% battery so it keeps failing. I'd like to know how to charge it in case of infinite reboot. I'm really afraid of using newflasher as a white guy, I can't understand what partitioning or whatever I said in other posts, adb always prompts waiting for device, and the driver is always a yellow exclamation mark. Please have no big brother to help me! I am more anxious to use the phone also stall on such a thing!
View attachment 5378119
Click to expand...
Click to collapse
Were you able to fix your phone? I have the same problem, I unlocked my phone and rooted it but then decided to relock my phone. Silly me i didn't charge my phone before using the Sony companion to repair it now it just keeps rebooting when I tried to charge it. Anyone has a solution to this is very much appreciated.
I had the same problem and brought it back to the store. It seemed that there was a problem with the fingerprint button, which kept the phone in restart boot. The only thing you need to do is to bring it back, have them/Sony check the phone. Ultimately you will get a New phone. I did. Yesterday. Hope it does not occur again.
I have same problem please help us. I have XQ-BC72 HK and I used New Flasher to flash RU or TW and corrupted. And I tried to fix with Xperia Companion but I have no charge.
Bro I solve the problem and phone is running now... Contact me...
THREAD LOCKED
First post and thread title removed by OP.
Regards,
shadowstep
Forum Moderator