Related
I now know the Allwinner A13 is a stripped down version of the Allwinner A10, to be clearer the specifications of my Tablet (from UniFlash and AnTuTu Benchmark) are as follows:
Manufacturer: None
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3, NEON)
CPU frequency: 60.0 ~ 1008.0 MHz
Screen resolution: 800 x 444
GPU vendor: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
RAM size: 512 MB DDR2 RAM
Knowing this, I used UniFlash to make a backup of the firmware bt after using UniFlash to try and load a CM9 Rom on to the Tablet, the Tablet died. After alot of googling I discovered AllWinner based chipsets use Live Suite (sometimes called LiveSuit) to flash firmwares on to the device.
To Flash firmware on to the device you need to follow the attached instructions ((http://dragondevs.com/viewtopic.php?f=159&t=390):
Download LiveSuite (http://www.softpedia.com/get/System/System-Miscellaneous/Live-Suit-Pack.shtml)
Install Live Suite
Start Live Suite
Select the Live Suite image file (folder icon
Turn device off (to be sure hold power button for 12 - 20 seconds)
Hold "Volume Up" button down
Connect the device to your PC (while still holding "Volume Up" down)
Start pressing the power button (you may need to do this once a second for 5/6 seconds)
If you haven't installed windows will ask to install a driver for a device (Dive Id will be something like Vf73465789123465435_Id, if the device is in the right mode, A13-MID, ADB-Interface indicates the tablet has connected in anouther mode).
Once this has finished LiveSuite will detect the device and a wizard will flash the firmware for you.
I have found a working firmware which according to AnTuTU Benchmark gives my tablet a rating of 3047 (see firmware section), this is on the higher end of reported A13-MID tablets
I have found out how to install CWM on to the device via SaussageMod (http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms/). This solution is untested, further more it may be unnessary futher investigation has shown this website (https://www.miniand.com/forums/forums/2/topics/73) has developed a way of create Live Suite images. This is simplier than installing clockworkmod recovery,
I tried to load the following images on to my tablet and failed completely: http://forum.xda-developers.com/showthread.php?p=31043317 It didn't work and forced me to do a firmware refresh.
My other step for the day was to create Ubuntu 10.10 installation then I began following this guide to construct an Xperia Play CM9 Rom/Kernel. once I have created a working ROM (I own an Xperia Play). I'm hoping to be able to modify the kernel to include the relevent A13 drivers, but one step at a time.
TODO
Create Ubuntu Partition
Follow Xperia Play CM9 Rom/Kernel Guide and create working rom (test on my Xperia Play)
Download CT repository (https://github.com/christiantroy) and compare with Xperia Play CM9 rom
Find the relevent drivers from https://github.com/amery/linux-allwinner leaked source
Retrieve offical MALI 400 MP drivers (parts of it have been released) compare with leaked source
Use UniFlash backup of original Rom along with LiveSuite image creation to try and restore original firmware (see If I understand it properly)
Examine Build.prop find out why original firmware displayed ina phone layout and new one is in tablet mode (potentially reference CM supported Tablets).
Attempt to compile a A13 (Sun5i) based rom
Create a google code page to hold all of these thoughts properly.
Left blank will include rom/firmwares here for future reference
Firmware
https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1 - My public Dropbox
http://www.azhuo.net/en/products_A13B_Allwinner-A13_7_inch_Android_4.0_Upgrade.html - password is: tabletpc
http://dragondevs.com/viewtopic.php?f=159&t=390 - McPad F1 firmware
Novo 7 Tools
https://dl.dropbox.com/u/74970692/Novotools_v1.0.apk
SausageMod
http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms
Gapps - http://goo.im/gapps/
I have the same tablet and it would be very cool if you succeeded in your attempt to create a CM9 rom for it. I tried ROM made by Tragidy from this thread but there is a problem with touchscreen driver, ROM booted successfully but I could not even unlock the screen cause touchscreen did not work. I finaly flashed rom DCPAD2121.zip using livesuite which I belive is the original ROM that came with tablet and it worked.
I installed clockwordmod using sausagemod successfully, but there is a big problem - no hardware "back" key and only volume up works.
novo7tools.apk works OK for reboot, reboot to recovery or shutdown.
syncing
Thanks, it's slow going at the moment, I only spending ~1 hour each day on it and at the moment trying to sync the CM9 source is painful (it keeps timing out, due to "remote side corruption").
I figure I would start there as all the firmware images I can find are ICS roms (meaning the drivers must be ICS).
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
WillingMagic said:
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
Click to expand...
Click to collapse
I tried that ROM, on my tablet after flashing the ROM it got stuck in a boot loop. It might be an idea to steal the config he created. The ROM is pre CM9 release. The A10 Flash kitchen software seems to work. I was hoping on producing a complete Live Suit image that people could flash (figuring our what CT has done on the A10 took a while).
Still having fun trying to sync the repositories, given up on trying to use a Debian VM, I'll will install full Ubuntu on a drive tomorrow, hopefully that will help fix things. It doesn't help most of the guides I can find are out of date and I keep having to make corrections.
I've also uploading all firmware I can find to my dropbox (at 200mb each they will take a while), I won't with tools simply because others ask you not too.
The Dropbox firmware was out of date when I tried to download it sun5i_android_a13-pfdq88_en_D06 firmware worked well for me, the firmwares are located at: https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
WillingMagic said:
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
Click to expand...
Click to collapse
I wiped the caches I couldn't send a logcat or dmesg as the device simply boot looped.
I've been providing links to threads whenever I come across others work, I'm new to android rom development for me this is a research effort which will hopefully produce something cool for my £50 tablet. Basically my day job has switched to developing UI's and I am looking for something new to learn (instead of why is Vaadin, Guice, SWT, Javascript, etc... is putting that button there).
Said dev career has also made me hate Git with a passion (not as bad as perforce but still) since Git integrates poorly with Visual Studio and Eclipse and you end up getting everyone overwriting each others changes. The idea of google code is simply because it makes a good platform for projects and you can use things like git with it. I didn't know about an Allwinner wiki, with all of my Googling I haven't come across it, where is it?
I don't care about build times I'm just researching, alas Debian has caused me enough problems so I've installed ubuntu on to a old disk I had lying around. Considering I've just tried to install Ubuntu via a Net install CD and it has screwed up the GRUB installation (nicely taking out my windows partition as well) can you blame me?
The reason for nabbing the config (and the Xperia Play and Christian Troys) is to understand how they work. Over the years I've found most Open Source software documentation is poor unless you have a set level of knowledge about it already.
Lastly I like automation, I want things to just work. Livesuit does that since I am normally a windows user, I as hoping in the distant future once I understand the build process to set up a Jenkins server to do it and create the whole lot automatically (via the Allwinner flash kitchen). In the even longer term I would like to update FlashTool to do what LiveSuit does. In the near term (next couple of months) I just want to be able to build a CM9 image.
All android and kernel source are keep on git, so changing it is stupid.
This is allwinner wiki: http://rhombus-tech.net/allwinner_a10 you can also update http://elinux.org/Hack_A10_devices
Everyone use CWM and it's standard for unofficial firmware/ROMS
brandonlee2 said:
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
Click to expand...
Click to collapse
Here's my upload, I packed it in rar format: http://www.mediafire.com/?we4zhgop29bg3dj
I also found it here: https://docs.google.com/open?id=0BzQuMwoMQqvba1VtQ1p1ZWJkR2M
from this forum post: http://www.slatedroid.com/topic/35314-a13-generic-tablet/page__view__findpost__p__421128
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
myfluxi said:
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
Click to expand...
Click to collapse
Mind sharing your repo ?
Trying 4.1.2
Hi all,
So I've tried compiling from 4.1.2 source for my A13 Emgeton Consul 3
It boots up and gets to the CM10 boot animation but it doesn't get past it.
I can adb at first boot until adb stops.
logcat from boot attempt:
http://pastebin.com/gLTrieHm
My build.prop:
http://pastebin.com/Ap9M1tjW
Any pointers as to why it doesn't get past the boot animation?
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
phoivos86 said:
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
Click to expand...
Click to collapse
Mine came pre-rooted.
Just received my MID A13 Tablet. Is this thread dead?
koodiifin said:
Just received my MID A13 Tablet. Is this thread dead?
Click to expand...
Click to collapse
I've gone a bit quiet on the development front, setting up a file/media server & samba domain server to power my home network is eating up my time.
My dropbox contains every image I could find for the tablet, as mentioned previously you can root the device using saussage mod, although my device and every one of those images is already rooted. You can prove this by installing super user.
Sassage mod's clockworkmod recovery doesn't work for me and I was looking at the backup tool in order to generate my own one. If you are aimed at any development, let me know and I will update the main thread
Many have said that they have "lost" "forget" to take backup from original rom. So, i'd like to have backup from my original to go back if/when something goes wrong. How do i do that? What software i need. Do i need to root?
This is from my info sheet:
Model TWD_MID
android version 6.0.1 ?????
Baseband 1.5
Kernel 3.0.8+
Buildnumber: nuclear_evb-eng6.0.1 IMM76D 20120917 test keys
I am in a desperate need for some help:
My tablets specs are these:
Phone model: A13-MID
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3.NEON)
CPU frequency: 60.0 - 1008.0 MHz
Screen Resolution: 800 x 444
GPU vendor: ARM
GPU render: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
Memory size: 353.5 MB
Android version: 4.0.4
Build number: nuclear_pfdq88c-eng 4.0.4 IMM76D 20120821 test-keys
Kernel: Linux version 3.0.8+
I just installed OpenVPN installer and installed the OpenVPN binary in the system/xbin
After that I tried to connect to my university's VPN but when it tried to connect, the tablet lost wifi connection and ever since it doesnt connect to any available wifi network!! I manually deleted the OpenVPN binary, but problem remains!
Do you know where could I find the stock ROM for this tablet in order to re-flash it?
Do you have any other proposals? Anything will help!
Thank you very much!!
Windows 8.0 phone - Good wireless connection; full battery; working Nokia and Microsoft accounts; enough empty space available; hard reset twice or more; correct time and date.
I do not receive any apps updates yet I always get an error message saying "We are currently unable to check for updates."
*first-time user of a windows phone
weird...
which version of software is on device? settings - about (version OS and firmware)
for easy check and flash latest official version of WP software you can use Nokia Software Recovery Tool, Windows 7 or 8.x is needed...
If you want to update to Preview for Developers WP8.1 version check here
dxdy said:
weird...
which version of software is on device? settings - about (version OS and firmware)
for easy check and flash latest official version of WP software you can use Nokia Software Recovery Tool, Windows 7 or 8.x is needed...
If you want to update to Preview for Developers WP8.1 version check here
Click to expand...
Click to collapse
thanks for replying
the version is OS 8.0.10211.204
firmware version 1232.5951.1249.1017
ahmedeissa said:
thanks for replying
the version is OS 8.0.10211.204
firmware version 1232.5951.1249.1017
Click to expand...
Click to collapse
is possible you have too old software and update server not recognize or give update for current phone version. you can use Nokia Software Recovery Tool to update to latest official WP8 version: 3051.40000.1349.0025 (this is latest official version of WP8.0 called "Black")... also dont forget to update Nokia system apps after software upgrade (you can use app SysApp Pusher from Store)
after if you want test version of WP8.1 via Preview for Developers, just use links from my previous post
thanks for replying. before i saw your reply i had already used Nokia Software Updater for Retail and i updated my phone's system
to firmware version: 3051.40000.1349.0002 and not 3051.40000.1349.0025 as you mentioned
and the software version is still OS 8.0 not 8.1 or other versions
when i connect to the software updater it tells me that there are no newer versions. it doesn't show the 8.1 version
8.1 not official released. You must activate Preview for Developers to install 8.1. Read my first post, there is link how to make this
Sent from my Lumia 920 using Tapatalk
dxdy said:
8.1 not official released. You must activate Preview for Developers to install 8.1. Read my first post, there is link how to make this
Sent from my Lumia 920 using Tapatalk
Click to expand...
Click to collapse
thanks for your reply. Is the phone's hardware compatible with android? (jellybean)
also there's freedom.apk for android phones, is there something similar to it that would work with windows phones?
also as you may know there's "black market" for android phones that allows you to download applications for free. is there something like it for windows phones 8.0?
ahmedeissa said:
thanks for your reply. Is the phone's hardware compatible with android? (jellybean)
also there's freedom.apk for android phones, is there something similar to it that would work with windows phones?
also as you may know there's "black market" for android phones that allows you to download applications for free. is there something like it for windows phones 8.0?
Click to expand...
Click to collapse
you cant flash android on WP devices or use apk files... is impossible... and why to go switch from horse to donkey
also no way to use black market or any other market on WP. Why you think WP OS is most secure OS without one malware or virus? because no c*ap and bogus app like on android...
if you want app for free watch for promotional period of apps.. in 3 year i collect pay software worth more than $2000... just be patient and many good apps and games can get free or for cheap price...
just use app as
http://windowsphone.com/s?appId=890485c3-7c32-42e3-b906-61ea62caeaa3
http://windowsphone.com/s?appId=e09858f0-0cf7-4b33-b754-54dd121b3c5d
http://windowsphone.com/s?appId=286ba4a5-33c3-489a-a5a1-8675503aadca
P.S.
all topic about illegal/pirated stuff here on forum is forbidden, but only for info you can use max 10 pirated XAP files on developer unlocked phone (but you must pay $19/year to Microsoft for Developer unlock)...
Similar, but worse problem here.
dxdy said:
is possible you have too old software and update server not recognize or give update for current phone version. you can use Nokia Software Recovery Tool to update to latest official WP8 version: 3051.40000.1349.0025 (this is latest official version of WP8.0 called "Black")... also dont forget to update Nokia system apps after software upgrade (you can use app ... from Store)
after if you want test version of WP8.1 via Preview for Developers, just use links from my previous post
Click to expand...
Click to collapse
Hello. I have a similar problem, and as you stated I believe the OS version is so old that the server does not recognize it. So I have tried several of Nokia's apps, Software Updater for Retail, Care Suite and they do recognize the phone, the software and it immediately states there is an update ready. However, when it tries to put the phone in Flash Update mode, the phone does not boot and I get an error saying there was a problem. If I disconnect the phone, press volumen-down and on buttons I can reset it and Works fine, but I am unable to do an update.
Here are the details for the phone:
Lumia 920
Country Variant PR
OS Versión 8.0.10211.204
Firmware revisión number 1232.5957.1308.0002
Radio Software version 1.0.202093.3
Firmware Update Notifier 1.1.0.3
Silent Installer 1.5.0.0
Build ID 153556
Extras+Info App Versión 3.8.1.10
I really don't know what to do. My phone hasn't even received GDR2, much less 3 and for sure it probably won't receive 8.1. Any information on how I can manually place the phone in Flash Update mode so maybe the care suite Works??? I was able, through the care suite to put in in test mode, but not in flash update mode.
Thanks in advance. Posting in the Nokia forums was absolutely no help at all. Could it be that I am doing something wrong with the care suite??? I used instructions from several sites to try to use the care suite.
To delete.
anaheiim said:
What is error?
Click to expand...
Click to collapse
Hello Anaheiim.
When the software tries to make the Nokia go into Flash Update mode, the phone stays at the NOKIA logo after rebooting. After about a minute, the application on the PC, say for example the Multisoftware Updater cancels out. In the case of Multisoftware updater, the error says : product in UEFI mode did not appear.
I can reset my phone and I get back the normal operations, but it appeas it never goes into a mode that is needed to download the software, or I don't have a driver or something similar to talk to the phone from my PC when it goes into that mode.
To delete.
anaheiim said:
What is error?
Click to expand...
Click to collapse
Hello Anaheiim.
When the software tries to make the Nokia go into Flash Update mode, the phone stays at the NOKIA logo after rebooting. After about a minute, the application on the PC, say for example the Multisoftware Updater cancels out. In the case of Multisoftware updater, the error says : product in UEFI mode did not appear.
I can reset my phone and I get back the normal operations, but it appeas it never goes into a mode that is needed to download the software, or I don't have a driver or something similar to talk to the phone from my PC when it goes into that mode.
To delete.
anaheiim said:
And following this tutorial? He said what? http://forum.xda-developers.com/showthread.php?t=2515453
The difference here is that you must go into flash mode manually.
Click to expand...
Click to collapse
Thanks Anaheiim. I am downloading the files in the requisities section of that thread and will follow the steps carefully. On your response you state "you must go into flash mode manually". But I don't see that mentioned in the tutorial, am I missing something??? Is there somewhere I can find how to place a Lumia 920 in flash mode manually???
Thanks again, at least I see a possibility of this working now!!!
To delete.
anaheiim said:
In the link that I give you
Part:
Follow the tutorial
Click to expand...
Click to collapse
Will do Anaheiim, thanks!!! Will follow the tutorial exactly and let you know how it goes. Super helpful, thanks. After the install I will leave a donation. Again, thanks a lot I can't tell you how helpful it is to have people like you that have gone through all this!
Hello again Anaheiim, unfortunatelly it has been no luck with the method you posted. I downloaded all the components fine. I downloaded the firmware I needed. I am able to get to the point when I try to recover the phone. I turn it off, plug the USB cord (already connected to the PC) and press the volumen down-power keys at the same time until I get ONE quick vibration. I then click the retry button on the tool on the PC. It starts trying to update, the phone shows the NOKIA logo mid-screen, most of the time it reboots and it shows it again and then goes directly into the Windows Phone logo and then back in to the start menú. Otherwise it just sits at the Nokia Logo. Either way, the PC App after a few minutes tells me it can't recover. Usually no error. Tried several different USB ports. Sometimes on some ports I get this error: DTL Connection: Could not connect to media. DTL Back-End error code = 0x8400A403. DTL Back-End: Driver initialization failed. DCM status code = 0x84004415, Common USB DCM: No device found from the target USB port, last error code = 0x80070003. .
Exception..
But that's it. Doesn't ever go into Flash Update mode.
To delete.
Re Register the softpub.dll
Disable third party firewall if any
Automatically detect settings for a proxy server from your LAN
SORRY WAS INACTIVE FOR SOMETIME... NOW IM BACK YOU CAN ASK AGAIN...
ALL CHIPSETS UNBRICKING METHOD HAS BEEN POSTED
Hi you may ask me anything related to android and I promise to answer within 24 hours and m reply will definitely work for you.
*****************************************************
SPECIALIST IN ROOTING, DEVELOPMENT, HACKING, SECURITY BYPASS, RECOVERY, FLASHING, CUSTOM ROM'S
*****************************************************
SEE YOU SOON
*****************************************************
•NOT RESPONSIBLE FOR ANY DAMAGE CAUSED TO YOUR DEVICE•
LG Aristo v10g Metropcs
How do i start configuring this phone without a google account?
A friend who was using it gave me this phone but forgot the boot password and the google account was not of him. So, now, we can´t use the phone.
Mephis96 said:
How do i start configuring this phone without a google account?
A friend who was using it gave me this phone but forgot the boot password and the google account was not of him. So, now, we can´t use the phone.
Click to expand...
Click to collapse
You mean to say that the phone is in frp mode?
(Factory reset protection)
Yes
FRP..... thanks, id did not know what it means.
Yes, it is in FRP
Mephis96 said:
FRP..... thanks, id did not know what it means.
Yes, it is in FRP
Click to expand...
Click to collapse
Can you please tell me the phone model and it's info.
LG Aristo v10g from Metropcs
x.ak**** said:
Can you please tell me the phone model and it's info.
Click to expand...
Click to collapse
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
[PC] HOW TO CURE A BRICKED M-TEK DEVICE!!
///////////////////////////////////////////////////////////////////////////////////////////
• Download and Install the Android USB drivers for your device that I have mentioned below.
• Power Off your device and remove the battery (only if it's removable)
• Download the stock ROM or the Custom ROM on your PC that you want to flash. (GIVEN BELOW)
• Download and extract SPFT (Smart Phone Flash Tool) on your PC, you will be able to see the files shown in the picture below. (Pic 1.1)
• Open Flash tool.exe (Pic 1.2)
• Once SPFT is launched tap on Download tab. (Pic 1.3)
• In download tab click on Scatter-Loading button. (Pic 1.4)
• Now locate the Scatter File that you will find in the Stock ROM folder that you downloaded in step 3. (Pic 1.5)
• Click on Download button to start the flashing process.(Pic 1.6)
• After finishing a success message will appear. (Pic 1.7)
///////////////////////////////////////////////////////////////////////////////////////////
Downloads:-
https://androiddatahost.com/b9cyw (DRIVERS)
https://spflashtool.com/download/SP_Flash_Tool_v5.1744_Win.zip (SPFT)
https://www.needrom.com/download/lenovo-s850/ (ROM FOR LENOVO S850, REGISTRATION NEEDED ON WEBSITE TO DOWNLOAD THE ROM)
///////////////////////////////////////////////////////////////////////////////////////////
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
I was working on another project that you can see below give me 1 hour I'll get back to you ASAP.
Best tool like SetCPU for controlling CPU with profiles?
SetCPU doesn't allow core control though
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
How to BYPASS FRP LOCK!
Test conducted on Virtual Machine on my PC
****************************************************************
I am not responsible for any damage you may cause to your device!
****************************************************************
****************************************************************
Never wanted to upload it but did it because I aim at helping people.
****************************************************************
Google FRP (factory reset protection) is aimed at making a stolen phone less valuable.
We usually keep our phones locked with a password or pattern but once its stolen it is easy to erase the data (via Hard Reset) and reuse the phone. With Google FRP in place, whenever the phone is formatted using hardware keys it will ask for the last synced google account details before proceeding further.
///////////////////////////////////////////////////////////////////////////////////////////
Until now, everytime some sort of hack comes out to bypass this screen and then its patched with a security update very soon. Same is the case with LG Aristo. There is a working solution as of now but it may not last long. Let’s see how to get this working –
///////////////////////////////////////////////////////////////////////////////////////////
How to Bypass LG Aristo Google Account –
This process is lengthy, but it’s a sure shot method and works every time.
We need 2 apps to complete this bypass process. They are Shortcut Master Lite and Sidebar Lite. Download the zip file from below link.
DOWNLOAD
>Extract the zip file and transfer the apk files to a micro sd card. Install the SD card in your LG Aristo before proceeding further.
///////////////////////////////////////////////////////////////////////////////////////////
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
Done
Drop a like on all my replies so I can stay encouraged and help you further.
YeshYyyK said:
Best tool like SetCPU for controlling CPU with profiles?
SetCPU doesn't allow core control though
Click to expand...
Click to collapse
You may use Kernel Manager it's super useful and will do what you're asking for!
Hi ! Could you help me with my problem ?? https://forum.xda-developers.com/search.php?searchid=446201503
No one seems to be able to help me... thanks a lot!!!!
antoflos said:
Hi ! Could you help me with my problem ?? https://forum.xda-developers.com/search.php?searchid=446201503
No one seems to be able to help me... thanks a lot!!!!
Click to expand...
Click to collapse
I will definitely help you just give me one hour but can you post the following info:
Model Number:
Exact Problem:
How that problem occured:
Model Number: SM-G935F / Galaxy S7 edge
Exact Problem : I can't go back to the dock ROM
How that problem occured : Last week, I wanted to try to change my phone a SM-G935F on a custom rom " Minotaurus Oreo V10". I did it successfuly but didn't like it so much so I decided to go back to stock Rom.
I used Odin and a stock ROM for that but I think I made a big mistake by not wiping with TWRP before flashing with Odin.
It resulted that my phone was stocked on the S7 edge logo. Luckly I can go on download mode so it's not hard bricked but Odin failed on every flash I've tried. It stoped at the step "config.msi"
To flash I used this dock Rom : SM-G935F_1_20161201150115_pbdym44h2s_fac
x.ak**** said:
I will definitely help you just give me one hour but can you post the following info:
Model Number:
Exact Problem:
How that problem occured:
Click to expand...
Click to collapse
Hey man this quite difficult and i need to install this phone's firmware on my VIRTUAL Machine, basically I request you to wait for the time being so I can save your phone.
Drop a like on all my comments above to encourage me.
Huawei P10+ Firmware on Huawei P10 - by accident
Hi:
On my P10, I used Firmwarefinder for Huawei to find the firmware (Oreo with EMUI 8) and after verifying, I downloaded and upgraded the P10 to new firmware. After reboot, the dpi is seemed changed (as picture attached) and when I went to check it on about phone, it says Model is VKY (which is Huawei P10+) - picture attached.
Is there a way to rollback and install the correct firmware on this phone somehow?
antoflos said:
Model Number: SM-G935F / Galaxy S7 edge
Exact Problem : I can't go back to the dock ROM
How that problem occured : Last week, I wanted to try to change my phone a SM-G935F on a custom rom " Minotaurus Oreo V10". I did it successfuly but didn't like it so much so I decided to go back to stock Rom.
I used Odin and a stock ROM for that but I think I made a big mistake by not wiping with TWRP before flashing with Odin.
Click to expand...
Click to collapse
***********************************************************************************
I AM NOT RESPONSIBLE FOR ANY FURTHER DAMAGE THAT MAY BE CAUSED TO YOUR DEVICE...(UNLIKELY TO HAPPEN)
***********************************************************************************
For being able to make the downgrade operation you will have to use a Windows based computer on which you will then install Odin (an official program developed by Samsung and used on update types of operations).
***********************************************************************************
Download Odin on your computer; afterwards install the program by following on screen prompts.
The Samsung Galaxy S7 Edge USB drivers must be installed on your PC too – use Samsung KIES in that respect.
Download the stock / official Android OS for your S7 Edge – from SamMobile or from Samsung’s official website.
Power off your device and reboot into download mode: press and hold the Power, Volume Down and Home buttons for a few moments; then connect your phone with your computer with the help of the USB cable.
After making sure that Odin has recognized your device (the “added” message must be displayed and the ID:COM field should be turned yellow or blue) from the program select the PA option.
Load the firmware file; don’t select the Re Partition and Auto Reboot options; click on Start when done.
Wait while your SGS7 Edge is being updated; when done, remove the USB cord and reboot your phone.
For further info related to the update process reply to my thread
LIKE ALL MY COMMENTS TO ENCOURAGE ME TO HELP YOU.
xironimoh said:
Hi:
On my P10, I used Firmwarefinder for Huawei to find the firmware (Oreo with EMUI 8) and after verifying, I downloaded and upgraded the P10 to new firmware. After reboot, the dpi is seemed changed (as picture attached) and when I went to check it on about phone, it says Model is VKY (which is Huawei P10+) - picture attached.
Is there a way to rollback and install the correct firmware on this phone somehow?
Click to expand...
Click to collapse
No pictures attached!! and yes you can roll back to the stock ROM or even customize the DPI according to your phone [ROOT REQUIRED]
Let me know which one you prefer?
Also like all my comments above to encourage me to help you even faster.
Hey out there,
my HDX 7 (thor) was running CM11 or CM12 for over two years - dunno actually which version in detail - and it was used by my parents, who actually gave me a call this week saying that the kindle won't start anymore. I'm not sure what they did, but it seems that it is now stucked in a bootloop - because it's only booting into fastboot mode when turning on.
ADB isn't working - I tried to flash a new recovery on fastboot mode - sadly I'm only receiving some writing error.
Is there a way to fix this issue with the loop, even when the device can only be adressed via fastboot?
Cheers!
chippler said:
Hey out there,
my HDX 7 (thor) was running CM11 or CM12 for over two years - dunno actually which version in detail - and it was used by my parents, who actually gave me a call this week saying that the kindle won't start anymore. I'm not sure what they did, but it seems that it is now stucked in a bootloop - because it's only booting into fastboot mode when turning on.
ADB isn't working - I tried to flash a new recovery on fastboot mode - sadly I'm only receiving some writing error.
Is there a way to fix this issue with the loop, even when the device can only be adressed via fastboot?
Cheers!
Click to expand...
Click to collapse
Yee - but it's not easy unless you have access to a Linux or OSX (Macintosh) platform. Upside is once successfully recovered you can install Lineage 14.1 which is a newer/mainstream varient of CM based on Android 7.x (Nougat). That said, carefully consider whether you have the skills, tools and stomach to take on this work given the age of the device (2013) and battery which is likely approaching EOL.
https://forum.xda-developers.com/kindle-fire-hdx/general/multi-platform-1-click-bootloader-t3241014
Davey126 said:
Yee - but it's not easy unless you have access to a Linux or OSX (Macintosh) platform. Upside is once successfully recovered you can install Lineage 14.1 which is a newer/mainstream varient of CM based on Android 7.x (Nougat). That said, carefully consider whether you have the skills, tools and stomach to take on this work given the age of the device (2013) and battery which is likely approaching EOL.
https://forum.xda-developers.com/kindle-fire-hdx/general/multi-platform-1-click-bootloader-t3241014
Click to expand...
Click to collapse
Thanks for your reply, already noticed your One-Click-Tool. Can it be used with any Linux distribution? Does it work with Live-CDs or VMs? I admit its much effort to put in, but I see it as a challenge. Actually I was going to use QDLoader -Method. If your tools works with Live-CD/VM I would give it a try.
chippler said:
Thanks for your reply, already noticed your One-Click-Tool. Can it be used with any Linux distribution? Does it work with Live-CDs or VMs? I admit its much effort to put in, but I see it as a challenge. Actually I was going to use QDLoader -Method. If your tools works with Live-CD/VM I would give it a try.
Click to expand...
Click to collapse
Not my original tool; you have @draxie to thank for that. No VMs or live-CDs TTBOMK.
Thx, then I will setup ubuntu on an external drive (usb stick e.g.). Tried Qloader today, but didn't worked due to the latest fw on it.
hello all
hope you're well during this difficult period
i have an android box called "t8-aml-v3"
the development for the device stopped shortly after i purchased it so its been stuck on 4.4.2 for a long time, it was fine but now all these new apps like netflix bein sports having issues with old software,
what I want to know is, is there any way i can flash the device to install just basic stock android the way we can do for any device such as a memory stick,
when i go into recovery mode etc and reset it it doesnt wipe it just factory reset, i even tried installing a rom using clockwork lol it goes through the process but when it reboots its just normal box
could someone please point me in the right direction?
@asustf700t
To get your question answered, if possible, run the Compatibility Test Suite (CTS) what is a free, commercial-grade test suite, available for download here. The CTS runs on a desktop machine and executes test cases directly on attached devices .
jwoegerbauer said:
@asustf700t
To get your question answered, if possible, run the Compatibility Test Suite (CTS) what is a free, commercial-grade test suite, available for download here. The CTS runs on a desktop machine and executes test cases directly on attached devices .
Click to expand...
Click to collapse
hello my friend
i see, okay thank you, i will do now and revert shortly, thanks!
edit -
i havent got a double sided type A so have ordered one from amazon, will let you know once it arrives and i am able to run the test,
cheers
jwoegerbauer said:
@asustf700t
To get your question answered, if possible, run the Compatibility Test Suite (CTS) what is a free, commercial-grade test suite, available for download here. The CTS runs on a desktop machine and executes test cases directly on attached devices .
Click to expand...
Click to collapse
Helllo
The cable arrived today and I downloaded the cts, it asked in the instructions to also install Android studio which I've done, but now I really don't know what to, I went to the install instructions in the website and here
https://source.android.com/compatibility/cts/setup
But I found it rather overwhelming, could you possibly simplify or point me to the exact instruction I need to follow?
I've installed android studio and downloaded/extracted the appropriate CTS version for my device..
Thank you
asustf700t said:
Helllo
...
But I found it rather overwhelming, could you possibly simplify or point me to the exact instruction I need to follow?
I've installed android studio and downloaded/extracted the appropriate CTS version for my device..
Thank you
Click to expand...
Click to collapse
Don't have the time to do so, sorry for this.
BTW: Wondering why you installed Android Studio: CTS works on device you connect to via USB.
jwoegerbauer said:
Don't have the time to do so, sorry for this.
BTW: Wondering why you installed Android Studio: CTS works on device you connect to via USB.
Click to expand...
Click to collapse
hello, ok thanks for your reply
it is because on the instructions I read i needed to use a linux PC to run a command to execute the cts and run it on my adroid device plugged in, i presume now that this isn't necessary lol,
i just need some clarity
Could anyone else possibly let me know