Hej, so i recently, actually 20 minutes ago, tried to flash my phones recovery... Which i totally failed, probably... So the symptoms are, Turns onto the POwered by android screen with a little text message saying Orange state and some other that it's not safe and stuff.
Making things harder this phone has a broken power button...
I followed every little detail of how to do it and stuff.
Hi , first you didn't give us any of informations ? What is model of your phone , did you tried with usb Jig stick ?
Teddy Lo said:
Hi , first you didn't give us any of informations ? What is model of your phone , did you tried with usb Jig stick ?
Click to expand...
Click to collapse
My phone: Just5 Cosmo L707
I used The ADB and Fastboot software.
Did you tried to flash with SP Flash tool and do you have firmware for your device ?
Teddy Lo said:
Did you tried to flash with SP Flash tool and do you have firmware for your device ?
Click to expand...
Click to collapse
No i did not try... Right now my phone is just in a boot loop where it stays a little, powers off, boots, stays a little, powers off.
Yeah i shuld have it, think...
If you have it just flash firmware with SP flash tool you will find scatter.txt inside of firmware if is right if not I don't know how to help you because the support for your phone provide just Manual , but not firmware .
Related
Hi everyone this is my first post. I have serious trouble. I bought a X10i few days back it was slow, I upgraded it using PCC. I was working fine but than i give it to my bro, it again slowed down and used to stuck so he restored it but dont know what happened it didnt complete. Now when i push the power button it vibrates and green light blinks but no response the screen remains black . I have no idea wat firmware it have and wat baseband it have. I used the flash tool 0.3.0, 0.2.9, 0.2.8 when i flash the firmware 2.1.A.045 global GGL, 3.0.1G.0.75 global ggl, 2.3_aro it goes into flash mode but at one stage or another it gives an error messsage "ABORT FLASHING" and somthing about turning on the debugging mode. I also used PCC and SEUS but it aborts in during installation, I than tried flash tool 0.2.5 and it flashed the X10i and give me message of flashing complete i did it with the firmware mentioned above but again. When i turn on the phone it just vibrates and green light blinks and nothing else even for two hours .
SO PLEASE I NEED HELP WHAT SHOULD I DO. NO SE Costumer Services here
civic_minded said:
Hi everyone this is my first post. I have serious trouble. I bought a X10i few days back it was slow, I upgraded it using PCC. I was working fine but than i give it to my bro, it again slowed down and used to stuck so he restored it but dont know what happened it didnt complete. Now when i push the power button it vibrates and green light blinks but no response the screen remains black . I have no idea wat firmware it have and wat baseband it have. I used the flash tool 0.3.0, 0.2.9, 0.2.8 when i flash the firmware 2.1.A.045 global GGL, 3.0.1G.0.75 global ggl, 2.3_aro it goes into flash mode but at one stage or another it gives an error messsage "ABORT FLASHING" and somthing about turning on the debugging mode. I also used PCC and SEUS but it aborts in during installation, I than tried flash tool 0.2.5 and it flashed the X10i and give me message of flashing complete i did it with the firmware mentioned above but again. When i turn on the phone it just vibrates and green light blinks and nothing else even for two hours .
SO PLEASE I NEED HELP WHAT SHOULD I DO. NO SE Costumer Services here
Click to expand...
Click to collapse
Could be a hardware LCD problem.
If it was lcd problem it must have sound and alerts but nothing
Try this: http://forum.xda-developers.com/showpost.php?p=17404856&postcount=4
thanks i will try any download links for the stock firmware
civic_minded said:
thanks i will try any download links for the stock firmware
Click to expand...
Click to collapse
Check the firmware or flash tool thread here or in the development forum.
I tried that too same result . What kind of forum is this no gurus or experts here who can give an expert advice or suggestion. Too much disappionted
only another "amateur" suggestion i'm afraid.
1) pull out battery (leave for 30 secs)
2) replace battery/DO NOT turn on
3) download a fresh install of SEUS.
4) run SEUS and follow instructions, complete as instructed.
5a) turn on phone, if fixed - yipee,
5b) if not - plug into usb and see if device shows in "computer"
6) (if 5b=yes) you know the phone is at least "contactable". good place to start for further troubleshooting.
7) post your results and be patient my friend, xda (x10) is currently up to its knees in new toys (unlocked bootloader) so people might take a moment to answer you.
hit thanks if i helped, seems my count is low no idea why, i think i'm helpful
Again I installed the fresh SEUS and did as instructed and no luck same result. It completely downloads the firmware but when it comes to installing the firmware its aborts. When i connect X10i to the pc it detects it as "SMEC Flash device" in device manager.
Further instruction needed
HELP!!!!!!!!!!!!!!!!!!!!
their is no firmware for so which fw should i use for flash and i dont know if the set came from other country so which fw should flash it with
If you plug in to your pc and open flashtool what does it (flashtool) say??
Sent from my X10i using XDA App
civic_minded said:
I am living in Pakistan and their is no firmware for so which fw should i use for flash and i dont know if the set came from other country so which fw should flash it with
Click to expand...
Click to collapse
Global generic
sounds silly, but charge the phone and make sure its not just really flat?
civic_minded said:
I am living in Pakistan and their is no firmware for so which fw should i use for flash and i dont know if the set came from other country so which fw should flash it with
Click to expand...
Click to collapse
I am no "Amateur or Noob", I gave you the reflashing options, as I said, if no reflashing option available here doesn't work, then it's probably a hardware issue or you're simply doing something wrong.
"[email protected] "
When i plug it into PC and flash tool is on, flash tool recognizes it and the phone can go into flash mode as well but if i go for root option than it say to connect the phone in usb and turn off the debugging
civic_minded said:
"[email protected] "
When i plug it into PC and flash tool is on, flash tool recognizes it and the phone can go into flash mode as well but if i go for root option than it say to connect the phone in usb and turn off the debugging
Click to expand...
Click to collapse
Debug mode has to be turned on in application settings in order for flash tool to be able to root the phone. Therefore all settings except flash option will be disabled.
+1, if flashing did not work then I'm afraid its out of my league! Good luck anyway, and remember, u catch more bees with honey.
Sent from my X10 using XDA App
[email protected] said:
+1, if flashing did not work then I'm afraid its out of my league! Good luck anyway, and remember, u catch more bees with honey.
Sent from my X10 using XDA App
Click to expand...
Click to collapse
thanks for the advice and i dont know why you guys are getting so much sentimental on what i said
Hi everyone! I'm asking a desperate help to solve a problem about recovery an almost bricked Huawei G610S-U00.
I tell you the story...
Few days ago I've tried to flash the original firmware of this device with the SP Flash Tool. The firmware has been downloaded from another forum.
The flash procedure ends successfully but when I've tried to reboot the phone it powers on correctly but the screen remain black. I can say it turn on correctly because you can see the back ligth of the screen and you also che feel the vibration pushing the power on button.
Now I think that the problem is due to an wrong scatter file or a wrong firmware version.
Now the situation is that the phone turns on and is recognized by the SP Flash Tool and I can do flashing operations but I need the correct files to flash.
Can anyone help me in this situation?
I really thank everyone could help!
Thank you very much
andbrigo said:
Hi everyone! I'm asking a desperate help to solve a problem about recovery an almost bricked Huawei G610S-U00.
I tell you the story...
Few days ago I've tried to flash the original firmware of this device with the SP Flash Tool. The firmware has been downloaded from another forum.
The flash procedure ends successfully but when I've tried to reboot the phone it powers on correctly but the screen remain black. I can say it turn on correctly because you can see the back ligth of the screen and you also che feel the vibration pushing the power on button.
Now I think that the problem is due to an wrong scatter file or a wrong firmware version.
Now the situation is that the phone turns on and is recognized by the SP Flash Tool and I can do flashing operations but I need the correct files to flash.
Can anyone help me in this situation?
I really thank everyone could help!
Thank you very much
Click to expand...
Click to collapse
No one can help?
Same problem here. I've downloaded a rom and flashed via SPFlash tools and I end at black screen. But once connected to usb the phone is recognized by the PC so it can be flashed if I have the right files. So if possible , someone with G610s , please make a whole backup and give us the file so we can flash . Please !
jazzymc said:
Same problem here. I've downloaded a rom and flashed via SPFlash tools and I end at black screen. But once connected to usb the phone is recognized by the PC so it can be flashed if I have the right files. So if possible , someone with G610s , please make a whole backup and give us the file so we can flash . Please !
Click to expand...
Click to collapse
Hi, I've solved the problem using a full backup given me from a friend.
I upload it to a cloud and then I will give you the link.
:good:
Mine is blank as well
andbrigo said:
Hi, I've solved the problem using a full backup given me from a friend.
I upload it to a cloud and then I will give you the link.
:good:
Click to expand...
Click to collapse
Hi bud, i understand it's an old thread but same thing happened to my G610 U00 and the only option i have is a proper rom for sp flashtool, please if you may, upload the link to the one that saved your phone, thanks ahead!
Hello, I have a big problem with the phone. It's no turning on after trying to flash.
I can see it as MTK USB Port (ComX), but there is no way to flash it again because of "enable dram failed (4032)" in FlashTool.
How to fix it?
pawelb93 said:
Hello, I have a big problem with the phone. It's no turning on after trying to flash.
I can see it as MTK USB Port (ComX), but there is no way to flash it again because of "enable dram failed (4032)" in FlashTool.
How to fix it?
Click to expand...
Click to collapse
Remove the back cover and connect your phone with the pc through data cable and kept pressing the red button for 10 secs which is near the sd card slot and release it. It will vibrate and lit up after 2-3 secs then remove the cable and start it.
Manek88 said:
Remove the back cover and connect your phone with the pc through data cable and kept pressing the red button for 10 secs which is near the sd card slot and release it. It will vibrate and lit up after 2-3 secs then remove the cable and start it.
Click to expand...
Click to collapse
It doesn't work. No vibration at all.
pawelb93 said:
It doesn't work. No vibration at all.
Click to expand...
Click to collapse
Prepare the rom to flash, then press firmware ugrade, plug your usb cable, keep pressed the red button for 20 secconds to reset preloader and tell us what is going on ?
stympy said:
Prepare the rom to flash, then press firmware ugrade, plug your usb cable, keep pressed the red button for 20 secconds to reset preloader and tell us what is going on ?
Click to expand...
Click to collapse
Now, I am also having the same problem. I followed your instruction but persist the same error DRAM FAILED 4032 and also I dont have any nandroid backup. Whether it will be related to preloader issue ?
Hi pawelb93 and Manek88,
+1
I'm having the same problem as well. I was using this tuto and all went fine because I got the big green circle of success from Flash tool. Then I unplugged my phone and it hasn't booted since. It was :crying: a 4GB international version with Jelly Bean 4.2.
d8v8n8 said:
Hi pawelb93 and Manek88,
+1
I'm having the same problem as well. I was using this tuto and all went fine because I got the big green circle of success from Flash tool. Then I unplugged my phone and it hasn't booted since. It was :crying: a 4GB international version with Jelly Bean 4.2.
Click to expand...
Click to collapse
My problem has been solved.
Hii d8v8n8 have you tried pressing the red button by plugging to pc ??
If you have a 4032 dram problem you need to format whole drive using sp flash tool and install a fresh stock rom.
Manek88 said:
My problem has been solved.
Hii d8v8n8 have you tried pressing the red button by plugging to pc ??
If you have a 4032 dram problem you need to format whole drive using sp flash tool and install a fresh stock rom.
Click to expand...
Click to collapse
Hi Manek88,
Yup, I pressed and pressed the red button, once even for a full minute without a break but to no avail.
However and fortunately from another poster, stympy, I got the suggestion that it might be a driver problem. For the unfortunate user, please click on the embedded links for the steps it took me to get things sorted out.
I wish sincerely for the wary who landed here to be able to solve his or her issue with our trials and errors posted here. Thank you all.
Club of anonymous brickers
Hi, I just wanted to leave a comment about how I unbricked my Chineese p780 4Gb. Maybe useful to somebody.
Flashed the wrong ROM, got the brick, the only sign of life was a red LED when connecting to USB. After the second flashing got the same DRAM_FAIL (4032) error. Finally, after finding the right ROM I got phone's screen blinking for a second, but still not loading and not functioning.
So, after some experiments I found out that fresh driver/tools versions do matter a lot and I managed to flash the same needed ROM with fresher tools.
Setup (can't post links, I downloaded these from lenovo-forums dot ru):
- driver SP_Flash_Tool_Driver_Auto_Installer_v1.1236.00
- SP_Flash_TOOLS v5.1352.01
- very nice light and functional ROM LiFe v0.7 with modified preloader
- alternative modem V51 S820
Good luck!
1eqinfinity said:
"Club of anonymous brickers"
Click to expand...
Click to collapse
:highfive:
1eqinfinity said:
(...) Finally, after finding the right ROM I got phone's screen blinking for a second, but still not loading and not functioning.
So, after some experiments I found out that fresh driver/tools versions do matter a lot and I managed to flash the same needed ROM with fresher tools. (...)
Good luck!
Click to expand...
Click to collapse
Thanks 1eqinfinity for confirming this :good: and I'm glad you were successful as well .
hello dear
I have samsung note3 clone sm-n9006 fcc id a3lsm-n9006 no way to flash it because of "enable dram failed (4032)" in FlashTool.
now phone is dead
How to fix it?
Please Help me Also
I rooted and Suddenly reset My phone My phone was Only showing Logo and i also Dont Have Any backup And I download Stock rom From Internet And Flashed My Phone By sp flash tool But After It Not Starting Please Help and Thankss Please
ShreyashM576 said:
I rooted and Suddenly reset My phone My phone was Only showing Logo and i also Dont Have Any backup And I download Stock rom From Internet And Flashed My Phone By sp flash tool But After It Not Starting Please Help and Thankss Please
Click to expand...
Click to collapse
Look for your phone on uncle Google and see what kind of hardware do you have....
After that you can repair the phone...
stympy said:
Look for your phone on uncle Google and see what kind of hardware do you have....
After that you can repair the phone...
Click to expand...
Click to collapse
My Phone Has Mt6582 Chipset And android lollipop
And It Doesnt Start
But Shows Com port On my pc i tried Flashing again By Sp flash tool but it say D Ram Fail
ShreyashM576 said:
My Phone Has Mt6582 Chipset And android lollipop
And It Doesnt Start
But Shows Com port On my pc i tried Flashing again By Sp flash tool but it say D Ram Fail
Click to expand...
Click to collapse
Can you tell me how many Gb have the internal memory and how much RAM?
NVM.
Try to flash one of this 3 Firmware. LINK HERE!
If you dont see anything inside the folders tell me! Or wait one hour to get uploaded!
stympy said:
Can you tell me how many Gb have the internal memory and how much RAM?
NVM.
Try to flash one of this 3 Firmware. LINK HERE!
If you dont see anything inside the folders tell me! Or wait one hour to get uploaded!
Click to expand...
Click to collapse
It has 1Gb Of Ram
And 8Gb Of internal Storage
Links To download Rom Is Not Showing
Will they work For my phone
ShreyashM576 said:
It has 1Gb Of Ram
And 8Gb Of internal Storage
Links To download Rom Is Not Showing
Will they work For my phone
Click to expand...
Click to collapse
Press on the "LINK HERE". Should take you to Google Drive.
Try second and third.
Should work.
ShreyashM576 said:
It has 1Gb Of Ram
And 8Gb Of internal Storage
Links To download Rom Is Not Showing
Will they work For my phone
Click to expand...
Click to collapse
It worked? How about some feedback?
And witch one!
Giving Brom Error S NOT ENOUGH MEMORY when using Third rom with given Flash Tool and I tried It with The Latest version Of Flash Tool but Its Not working Now Trying Second Rom
ShreyashM576 said:
Giving Brom Error S NOT ENOUGH MEMORY when using Third rom with given Flash Tool and I tried It with The Latest version Of Flash Tool but Its Not working Now Trying Second Rom
Click to expand...
Click to collapse
Ok. Waiting for feedback.
Hello Everyone,
I Rooted My Galaxy S2 (Indian 'G' Version), Then Installed A recovery Via ROM manager app. I forgot to unlock Bootloader, Then I downloaded CM11 Nighlty ROM zip....... Inside the zip there was Boot.img (which i thought that it is Cwm recovery) and flashed it with an app and it failed to flash.... And I rebooted my phone and BOOM!! My phone's dead.... Bricked (i think so)..... No Display, No download Mode, Nothing! I tried to bring it to download Mode by USB JIG..... But still no Luck! Please Help me friends! (Pardon me if I posted in wrong place! This is my first time in XDA)
Hello ... calm .. everything has solution .. we are going to see what can be ... tell me ... the phone when you plug to the charger ... has take the load? it has appear something on screen?
leocadenas said:
Hello ... calm .. everything has solution .. we are going to see what can be ... tell me ... the phone when you plug to the charger ... has take the load? it has appear something on screen?
Click to expand...
Click to collapse
No Sir, When I keep that for chargingbnothing Happens! No display! The phone won't turn on with battery but gets heated near camera area. Also I used 'Rashr' app to flash boot.img from nightly zip. Tried USB jig but still invain.
Amogh Thambi said:
No Sir, When I keep that for chargingbnothing Happens! No display! The phone won't turn on with battery but gets heated near camera area. Also I used 'Rashr' app to flash boot.img from nightly zip. Tried USB jig but still invain.
Click to expand...
Click to collapse
if you can't get into download mode in any way, your phone is bricked. There is nothing you can do now.
gsstudios said:
if you can't get into download mode in any way, your phone is bricked. There is nothing you can do now.
Click to expand...
Click to collapse
Okay. Thanks a lot! I guess I have to change it's motherboard!
Amogh Thambi said:
Okay. Thanks a lot! I guess I have to change it's motherboard!
Click to expand...
Click to collapse
yep, that's one way to solve it.
I think the same.. but ....... to obtain a new motherboard.. at least .. in my country .. mmmmm it is impossible!!! only used.... and not ten points.... Where are you Amogh Thambi ?
leocadenas said:
I think the same.. but ....... to obtain a new motherboard.. at least .. in my country .. mmmmm it is impossible!!! only used.... and not ten points.... Where are you Amogh Thambi ?
Click to expand...
Click to collapse
Here in India, A local shop owner told me that he could replace the motherboard for 3000RS (50$ approx) or Revive my hardbricked phone by repairing it for 1500RS (25$ Approx). It will be double cost if I go to official Samsung Care.
Amogh Thambi said:
Here in India, A local shop owner told me that he could replace the motherboard for 3000RS (50$ approx) or Revive my hardbricked phone by repairing it for 1500RS (25$ Approx). It will be double cost if I go to official Samsung Care.
Click to expand...
Click to collapse
Did you try changing your battery? Try to find a similar Samsung Battery and boot into download mode then. The boot.img is the kernel, and if it didn't flash, the ROM/Stock ROM should still boot up, or at the maximum should give you a bootloop. I still feel it is some battery fallacy, since the processes which you followed don't have any such errors.
Regards.
warrior1208 said:
Did you try changing your battery? Try to find a similar Samsung Battery and boot into download mode then. The boot.img is the kernel, and if it didn't flash, the ROM/Stock ROM should still boot up, or at the maximum should give you a bootloop. I still feel it is some battery fallacy, since the processes which you followed don't have any such errors.
Regards.
Click to expand...
Click to collapse
When i flashed boot.img the battery was almost full.... After it failed to flash... I rebooted to see if everything was okay... But Boom! After i pressed reboot to recovery the phone turned off and died..... Also in the repair shop, we tried booting up with electric source but still no luck! First Weird and Bad experience with samsung
Amogh Thambi said:
Hello Everyone,
I Rooted My Galaxy S2 (Indian 'G' Version), Then Installed A recovery Via ROM manager app. I forgot to unlock Bootloader, Then I downloaded CM11 Nighlty ROM zip....... Inside the zip there was Boot.img (which i thought that it is Cwm recovery) and flashed it with an app and it failed to flash.... And I rebooted my phone and BOOM!! My phone's dead.... Bricked (i think so)..... No Display, No download Mode, Nothing! I tried to bring it to download Mode by USB JIG..... But still no Luck! Please Help me friends! (Pardon me if I posted in wrong place! This is my first time in XDA)
Click to expand...
Click to collapse
Hi, when you connect you i9100 to computer do get any response, like any beeping sound in pc or failed to find drivers error when connected to pc ?
jaysan2 said:
Hi, when you connect you i9100 to computer do get any response, like any beeping sound in pc or failed to find drivers error when connected to pc ?
Click to expand...
Click to collapse
Mine is I9100G ........ And when i connect to PC with battery nothing happens! But when i connect to PC with battery removed it shows "Failed to recognise device" and then it disappears!
Amogh Thambi said:
Mine is I9100G ........ And when i connect to PC with battery nothing happens! But when i connect to PC with battery removed it shows "Failed to recognise device" and then it disappears!
Click to expand...
Click to collapse
hi, as i have seen your posts you have written that you do have tried jig, and no results. try to take out battery and connect the jig and put the battery, i believe this the last chance you might have through jig. Or just jtag it for 25$ it is not that expensive, let me know what happens with jig.
So my phone just got stuck while normal usage. Tried restarting and the phone began boot looping.
Did plenty of research and finally decided to flash. Tried to flash using mi flash in fastboot mode but failed then google search made me realise my bootloader was locked. Did more research and decided to flash using test point EDL method.
Things went pretty well and the flash (miui v8) and the process became successful and when I powered my device the phone went back to boot loop again.
Tried flashing again and the result was the same.
It would be really helpful if somebody could actually help clear the issue. Did pretty much everything I could do as a newbie to flashing.
thank you!
There are 2 varients of rn4 one is mediatek(note 4x) and the other is Snapdragon so check if u flashed right firmware
thisbearisdrunk said:
There are 2 varients of rn4 one is mediatek(note 4x) and the other is Snapdragon so check if u flashed right firmware
Click to expand...
Click to collapse
No, I have flashed the correct file(Mido) and the flashing process went quite well but the problem still exists.
M i L i N said:
No, I have flashed the correct file(Mido) and the flashing process went quite well but the problem still exists.
Click to expand...
Click to collapse
How is ur phone being recognised in mi flash tool?
A serial number appears or something else like "com_port" appears?
thisbearisdrunk said:
How is ur phone being recognised in mi flash tool?
A serial number appears or something else like "com_port" appears?
Click to expand...
Click to collapse
It's recognised as COM4 the first time I tried then sometimes when I connect it shows COM3.
M i L i N said:
It's recognised as COM4 the first time I tried then sometimes when I connect it shows COM3.
Click to expand...
Click to collapse
If it recognises ur phone like that then flashing does nothing to ur phone so the only way is to go into edl mode and then flashing
https://forum.xda-developers.com/re...ool-redmi-note-4-edl-mode-o-removing-t3684024
Use this tool to go into edl mode and then flash
This thread can help ,because i bricked my phone once without unlocking the bootloader and the miflashtool recognised my phone like how it recognised urs and this thread saved my phone
Good luck