Related
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
your not the only one with this problem i have it too with same mt6575 someone help please
Need to uninstall device and reinstall drivers
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
ronbo76 said:
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
Click to expand...
Click to collapse
Your USB program does give a lot of information I have never seen before, but I still haven't been able to figure out how to get the driver to load.
thanks, John
I'm having the same problem installing the MT6575 USB VCOM drivers. Is there a workaround to get this installed? I"m using WIN 6 64bit
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
ivy13 said:
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
Click to expand...
Click to collapse
Tried your first method but still get Code 10 error. Could not understand your second method. Please help. Me device is Qmobile Noir A2
hye.. any progress? am having the same issue.. just for MTK6575 com port driver
Just made my Amoi N820 work
So happy
You get Code 10 becouse your windows couldn't recognize the driver but that's irrelevant becouse flashing will work
No solution?
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
orion~X said:
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
Click to expand...
Click to collapse
i have thet problem to.
is ther solution?
I HAVE SOLUTION FOR THIS PROBLEM!!
Just ignore the error Code 10! Start the SPFlashtool and load the scatterfile, click on download and connect your switch off Phone with the computer. It will work fine.
Having the Same Problem
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Hi.
me test for me not work.
iphone 4s.
plz help me.
hihi2u2 said:
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Click to expand...
Click to collapse
Did you ever get this problem solved as I have the same issue with an MTK 6592 chip based phone?
I have the same problem too.
Installation of Media Tek preloaded drivers gives me Code 10 error.
Has anyone found the solution?
my phone is totally dead without power now after I tried to flash with SP Flash tool using correct ROM. I noticed in device manager that there is a CODE 10 error in mediatek preloader usb driver.. is this the culprit? my phone can no longer be detected now in SPFlash or MTK Droid tools... so hopeless... this is a brandnew phone I bought to be given as gift to my cousin...
I did it! I did it! I did it!
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
I've been struggling with my UMI Rome for days. It has/had the black screen problem, sometimes won't enter recovery mode, sometimes wouldn't allow charge, sometimes works just fine (yesterday). Last night i mistakenly cut off power during a battery recharge. -- today it has all the above problems (bricked) so I am trying doing a flashing again using the tutorials and tools on the Tehnotone.com site. Sintetix's reply above helps me at least have a better clue on what is going on. Wish me luck! BTW, I am using a Dell Windows 10 pc. (Results to be reported here.)
Sintetix said:
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
Click to expand...
Click to collapse
I tried what you said. It wouldn't install properly. It kept saying error (code 10) and showed in device management with a caution sign every time I installed the driver. I disabled the forced driver signature thingamabop but it still does it. I guess I'm screwed. Has anyone else fixed this?
I have a motorola motostart (xt390) and wish to unlock bootloader, root, etc. Nevertless, I just can't get into fastboot mode.
Powering up with VOL Down it access the recovery mode. The same for VOL UP+DOWN.
When i try powering up with VOL UP pressed the device simply don't power up.
Is it a malfunctioning device or some roms for this hardware simply have mysteriuos ways to enter fastboot?
The ROM is a brazilian retail, Gingerbread (2.3.6) version MAUI.11AMD.W11.37.SP.V9.F4.P1, build: ARGONM_W_07.15.04R_D.
Please! Help!
Nobody? hehehe
I have found a clue: if I plug the device without batery and hol VOL_UP the windows detect, and install the drivers, to a "MTK USB Port (COM X)". If I release the VOL_UP the USB port gets disconected.
Someone know what I can do with a MTK port?
erlyneto said:
I have found a clue: if I plug the device without batery and hol VOL_UP the windows detect, and install the drivers, to a "MTK USB Port (COM X)". If I release the VOL_UP the USB port gets disconected.
Someone know what I can do with a MTK port?
Click to expand...
Click to collapse
I think that's the same as download mode for when you have to flash it with SPFT. That's how I get spft to recognize my O+8.75.
xshinta9 said:
I think that's the same as download mode for when you have to flash it with SPFT. That's how I get spft to recognize my O+8.75.
Click to expand...
Click to collapse
Sorry by my ignorance, but SPFT is a software?
I find the SPFT that you mentioned. But, as far as I could understand the software, it is used to flash or dump rom from MTK based phones.
But there are problems:
1)XT390 appears to be based on MTK6*** phones, but is not the same, so, the roms should not work in it, right?
2)I can't use this tool to send commands to the device (like fastboot mode on other Motorola android phones), so i can't get my device id to unlock the bootloader in the morotola web site...
Do you know anything about that software, its roms and XT390? There are any ways to open a command line utility on it?
Hi bro, unfortunately I have zero knowledge on it thus far. 'am figuring out how to unlock my phone's bootloader as well, (it's a local-based chinese phone as well that's marketed under a different name)
Hello please help i have a big problem on my NEO N003 1/4g T13
I have flashed to newest Stock room from the website neo then i try magerto room he was fine as the beginning then after 2 days he start freezing and sometimes working then the camera is no longer working i tell my self its just poor room
i decide to use the stock room but after i flashed work normal for 10 minute then freeze the screen turn black utile you remove the battery and put back in 2 minutes
after many times trying to flash it by sp flash tool i hit format ...my imei is gone and no signal on the sim card ( thats not a big problem)
but the phone still freezing and restarting ...black screen ......
after that the phone not able to turn on even the logo just black you can see he is trying turn on but no logo no nothing
in the device manager detect MediaTek Usb port before was detect preloader MediaTek somthing ......
look at the picture and the sp tool not working MediaTek Usb port and i got this error (look at the picture)
please help me i use the phone only 1 month please help me
this Morning accidentally i put the phone into Preloader Mode and make normal flash and my phone is a live a was very Happy i went to write the imei must root the phone...i have install root programe name is geno (he is work fine on lenovo P780) but in neo N003 he just freeze and tun off and no longer can trun it on again just black screen.
Now when i plug the phone via usb port windows detect it MediaTek USB Port how i can put it again in Mediatek Preloader VCOM ???
Always get error 4032 on sp flash tool (format , upgrade, download) all he same error
Guys please Help me .
Please Help Help !!!!!
Help me For God Sake I am going Crazy !!!!!
benladen said:
Hello please help i have a big problem on my NEO N003 1/4g T13
I have flashed to newest Stock room from the website neo then i try magerto room he was fine as the beginning then after 2 days he start freezing and sometimes working then the camera is no longer working i tell my self its just poor room
i decide to use the stock room but after i flashed work normal for 10 minute then freeze the screen turn black utile you remove the battery and put back in 2 minutes
after many times trying to flash it by sp flash tool i hit format ...my imei is gone and no signal on the sim card ( thats not a big problem)
but the phone still freezing and restarting ...black screen ......
after that the phone not able to turn on even the logo just black you can see he is trying turn on but no logo no nothing
in the device manager detect MediaTek Usb port before was detect preloader MediaTek somthing ......
look at the picture and the sp tool not working MediaTek Usb port and i got this error (look at the picture)
please help me i use the phone only 1 month please help me
this Morning accidentally i put the phone into Preloader Mode and make normal flash and my phone is a live a was very Happy i went to write the imei must root the phone...i have install root programe name is geno (he is work fine on lenovo P780) but in neo N003 he just freeze and tun off and no longer can trun it on again just black screen.
Now when i plug the phone via usb port windows detect it MediaTek USB Port how i can put it again in Mediatek Preloader VCOM ???
Always get error 4032 on sp flash tool (format , upgrade, download) all he same error
Guys please Help me .
Click to expand...
Click to collapse
benladen said:
Help me For God Sake I am going Crazy !!!!!
Click to expand...
Click to collapse
Why no one try to Help me please
:crying::crying::crying::crying::crying::crying::crying::crying::crying::crying:
Up up up
help !!!!
benladen said:
Up up up
help !!!!
Click to expand...
Click to collapse
help
benladen said:
Now when i plug the phone via usb port windows detect it MediaTek USB Port how i can put it again in Mediatek Preloader VCOM ???
Always get error 4032 on sp flash tool (format , upgrade, download) all he same error
Guys please Help me .
Click to expand...
Click to collapse
On my phone, mine has the same chip as yours, to flash in preloader mode, I do it in this order,
1 connect phone to pc via usb with battery removed,
2 load flashtool with scatterfile and rom to flash,
3 click on download in flashtool,
4 put battery into phone
SPflashtool then searches for the preloader driver, loads it briefly and then loads the DA Usb Vcom port driver and then proceeds with flashing
This will only work if you have the usb vcom preloader drivers installed on your pc
To check if you have preloader driver installed, open device manager on your pc, connect your phone with usb cable and battery removed, put in battery while watching device manager, if driver is installed you should see 'Preloader Usb Vcom port' appear in the ports section,
but it will only be there for a few seconds, and will dissappear again. If you do not see this you need to install the Vcom driver.
Hope this helps
you help me a lot man !!!!!
oscarblue48 said:
On my phone, mine has the same chip as yours, to flash in preloader mode, I do it in this order,
1 connect phone to pc via usb with battery removed,
2 load flashtool with scatterfile and rom to flash,
3 click on download in flashtool,
4 put battery into phone
SPflashtool then searches for the preloader driver, loads it briefly and then loads the DA Usb Vcom port driver and then proceeds with flashing
This will only work if you have the usb vcom preloader drivers installed on your pc
To check if you have preloader driver installed, open device manager on your pc, connect your phone with usb cable and battery removed, put in battery while watching device manager, if driver is installed you should see 'Preloader Usb Vcom port' appear in the ports section,
but it will only be there for a few seconds, and will dissappear again. If you do not see this you need to install the Vcom driver.
Hope this helps
Click to expand...
Click to collapse
Thank you so much man you help me a lot !!!
This how i get preloader
1-remove the battery
2-connect the phone to usb but before windows detect the device put the battery back
windows will detect preloder driver !!that's great
Now must go to my office i have windows 7 there to flash the phone with stock room and i will put the result later here
because i have win8.1 at home i get a lot of problem flashing this phone on it .
thank's again Peace.
oscarblue48 said:
On my phone, mine has the same chip as yours, to flash in preloader mode, I do it in this order,
1 connect phone to pc via usb with battery removed,
2 load flashtool with scatterfile and rom to flash,
3 click on download in flashtool,
4 put battery into phone
SPflashtool then searches for the preloader driver, loads it briefly and then loads the DA Usb Vcom port driver and then proceeds with flashing
This will only work if you have the usb vcom preloader drivers installed on your pc
To check if you have preloader driver installed, open device manager on your pc, connect your phone with usb cable and battery removed, put in battery while watching device manager, if driver is installed you should see 'Preloader Usb Vcom port' appear in the ports section,
but it will only be there for a few seconds, and will dissappear again. If you do not see this you need to install the Vcom driver.
Hope this helps
Click to expand...
Click to collapse
Hello, I can't Flash the phone over the preloder i have try 2 pcs and 2 diffrent drivers no luck the sp tool give me errors 4010... 2020
after trying many times i got flashed over the mediatek usb port ....
then the usb disconnect and the MediaTek DA USB VCOM connect and the flash begin utill 100%
but the phone not starting just black screen
try to format , upgrade , download nothing try 23 stock roms the old and the new nothing
please help help !!!
Do you see the preloader driver in device manager when you connect your phone as I described above?
Which build of SPflashtool are you using? the tool is quite buggy and sometimes helps to try another version
oscarblue48 said:
Do you see the preloader driver in device manager when you connect your phone as I described above?
Which build of SPflashtool are you using? the tool is quite buggy and sometimes helps to try another version
Click to expand...
Click to collapse
I don't see preloader driver i see just mediatek usb port
I am using SP Flash Tool v3.1328.0.183 and other versions
Now the flash not working again stop at the red bar 100% and give error 4032
i am sick with that error
i read some people get they phones alive with an loading an other preloader and the flash get throw !!!
look at this
thank you for responding man.
any One what i can do now ??!!!
Help for god sake !!
Ok, i think the only way your going to unbrick your phone is to flash the exact correct rom for it, Do you have a copy of the stock rom for your phone suitable for SPflashtool?
The link that you show is for a Feiteng H9500, that is very unlikely that it will work on your phone, the reason your phone is bricked is because you have probably flashed the wrong preloader block, and that is whats causing the trouble, you need to make sure you have the correct rom for your device before you start.
I think the only time you had a little success is when you accidentally entered preloader mode and if it were my phone I would concentrate on getting the preloader driver installed. There are some tutorials on here to install the drivers, it can be a bit tricky, and not all mediatek devices are the same, so a bit of trial and error may be needed
Once you have the Preloader usb vcom drivers installed I would then attempt to flash just the preloader and dsp_bl blocks initially from the correct rom for your phone, and then if successful flash the remainder of the rom, without preloader and dsp_bl
If you flash the wrong preloader/dsp_bl you will almost certainly brick your phone, so it must be either from a backup you have made of your original rom or from the exact stock rom for your phone.
oscarblue48 said:
Ok, i think the only way your going to unbrick your phone is to flash the exact correct rom for it, Do you have a copy of the stock rom for your phone suitable for SPflashtool?
The link that you show is for a Feiteng H9500, that is very unlikely that it will work on your phone, the reason your phone is bricked is because you have probably flashed the wrong preloader block, and that is whats causing the trouble, you need to make sure you have the correct rom for your device before you start.
I think the only time you had a little success is when you accidentally entered preloader mode and if it were my phone I would concentrate on getting the preloader driver installed. There are some tutorials on here to install the drivers, it can be a bit tricky, and not all mediatek devices are the same, so a bit of trial and error may be needed
Once you have the Preloader usb vcom drivers installed I would then attempt to flash just the preloader and dsp_bl blocks initially from the correct rom for your phone, and then if successful flash the remainder of the rom, without preloader and dsp_bl
If you flash the wrong preloader/dsp_bl you will almost certainly brick your phone, so it must be either from a backup you have made of your original rom or from the exact stock rom for your phone.
Click to expand...
Click to collapse
Thank you for you respond ,
i have Preloader usb vcom inslalled on my PC i have 3x stock roms from the NEO website all does not working always red bar 100% and get error 4032 on SP flash tool
Do you want to say that i will contact someone have the same model of my phone and tell him to make backup to his phone and upload it for me ? is it right ?
i have lenovo P780 when i turn it off and plug it to usb he detect it preloader mediatek then Disappears , thats what the NEO N003 must be :crying:
any way if some one have a rom work with my phone plz upload it for me
thank you again peace.
benladen said:
Thank you for you respond ,
i have Preloader usb vcom inslalled on my PC i have 3x stock roms from the NEO website all does not working always red bar 100% and get error 4032 on SP flash tool
Do you want to say that i will contact someone have the same model of my phone and tell him to make backup to his phone and upload it for me ? is it right ?
i have lenovo P780 when i turn it off and plug it to usb he detect it preloader mediatek then Disappears , thats what the NEO N003 must be :crying:
any way if some one have a rom work with my phone plz upload it for me
thank you again peace.
Click to expand...
Click to collapse
So the preloader vcom driver is installed ok on your pc, but you do not see it when you connect your phone, maybe you need to connect in a different way, on my phone I have to connect switched off phone with the battery removed, and when the battery is put in, then you see preloader driver pop up in device manager, there are many different MTK phones and different ways to connect.
The stock rom you have should be fine as long as it is the correct one for your device.
oscarblue48 said:
So the preloader vcom driver is installed ok on your pc, but you do not see it when you connect your phone, maybe you need to connect in a different way, on my phone I have to connect switched off phone with the battery removed, and when the battery is put in, then you see preloader driver pop up in device manager, there are many different MTK phones and different ways to connect.
The stock ROM you have should be fine as long as it is the correct one for your device.
Click to expand...
Click to collapse
the phone does not start at all not logo no no nothing is just black screen i have try this before connect the device then put the battery on it when it connect it's work first time the preloader device show , but i can not flash the ROM with it the sp flash tool give me error
i was able the flash it with mediatek usb port but the phone does not start black screen
, now i can't enter to the preloader device or even flash it with mediatek usb port !!!!!
yes its correct ROM i flash the phone with it before ...i brick the phone by root it by software name GENO the phone just stop working
i have use all the combination button but not luck i am stuck at mediatek usb port and sp tool give me error 4032....
:crying::crying::crying:
benladen said:
the phone does not start at all not logo no no nothing is just black screen i have try this before connect the device then put the battery on it when it connect it's work first time the preloader device show , but i can not flash the ROM with it the sp flash tool give me error
i was able the flash it with mediatek usb port but the phone does not start black screen
, now i can't enter to the preloader device or even flash it with mediatek usb port !!!!!
yes its correct ROM i flash the phone with it before ...i brick the phone by root it by software name GENO the phone just stop working
i have use all the combination button but not luck i am stuck at mediatek usb port and sp tool give me error 4032....
:crying::crying::crying:
Click to expand...
Click to collapse
If your phone now is completely dead, probably your only hope of reviving it is by using the test point, see 'Modes of the virtual COM ports', here.....
http://forum.xda-developers.com/showpost.php?p=38369102&postcount=11
Ive never done this procedure, so cant help much with it, but if you search these threads for mediatek test point or similar, you might find some info on it
oscarblue48 said:
If your phone now is completely dead, probably your only hope of reviving it is by using the test point, see 'Modes of the virtual COM ports', here.....
http://forum.xda-developers.com/showpost.php?p=38369102&postcount=11
Ive never done this procedure, so cant help much with it, but if you search these threads for mediatek test point or similar, you might find some info on it
Click to expand...
Click to collapse
ok thank you i will see what i can do !!
oscarblue48 said:
If your phone now is completely dead, probably your only hope of reviving it is by using the test point, see 'Modes of the virtual COM ports', here.....
http://forum.xda-developers.com/showpost.php?p=38369102&postcount=11
Ive never done this procedure, so cant help much with it, but if you search these threads for mediatek test point or similar, you might find some info on it
Click to expand...
Click to collapse
Hello, man can you Help me to find Test point
look at the picture down here
thank you.
benladen said:
Hello, man can you Help me to find Test point
Click to expand...
Click to collapse
As I said, Ive never done this myself, only read about it and have no idea where the test point is on your phone, they all appear to be in different places, on an mt6577 I had previously it was easy to find, just by the sim slot, there was no need to even strip the phone down, but on most other models they all seem to be less accessible. It will be somewhere on the main board I would imagine, usually, but not always, a small round brass dot about 2mm accross, and I noticed while searching that some are marked 'KCOLO' or similar. I believe also from what I've read that the manufacturers use this method to input the factory rom, so it must be there somewhere, its just a question of locating it. The best method to find it apparently is by testing different points with a multimeter to find one that corresponds with your battery output.
some more info here... http://forum.xda-developers.com/showpost.php?p=32424838&postcount=616
and a link to rua1's russian thread on the subject, translation with google chrome is not very good but there are some pics throughout the thread that might be helpful.... http://forum.china-iphone.ru/test-pointi-dlya-proshivki-preloader-na-mt6573-75-77-t22559.html
I have an issue after flashing Aerom: Unfortunately I forgot to untick preloader when I flashed the rom. Installation went fine but device is not detected anymore by preloader driver. I tried different windows PCs without success. Flashing with SP Tools is not possible.
Bootloader (and ADB) mode working. Fastboot detects the device (in device manager it is listed as HTC Dream) In developer settings ADB and oem unlock are Activated. If I try to unlock boot loader via "fastboot oem unlock", I cannot select "Yes" (Volume up) on the device, only "No" (Volume Down)....not rooted, no custom recovery
How can I recover the right preloader or install custom recovery?
alohahe3000 said:
I have an issue after flashing Aerom: Unfortunately I forgot to untick preloader when I flashed the rom. Installation went fine but device is not detected anymore by preloader driver. I tried different windows PCs without success. Flashing with SP Tools is not possible.
Bootloader (and ADB) mode working. Fastboot detects the device (in device manager it is listed as HTC Dream) In developer settings ADB and oem unlock are Activated. If I try to unlock boot loader via "fastboot oem unlock", I cannot select "Yes" (Volume up) on the device, only "No" (Volume Down)....not rooted, no custom recovery
How can I recover the right preloader or install custom recovery?
Click to expand...
Click to collapse
Having just gone through the joy of unbricking my new P9000, after I didn't untick preloader when flashing, I've learned more today about using "meta-mode" with a MediaTek phone than I ever wanted to!
This is what debricked my phone. I wonder if this is of use to you? I make no claims it won't brick your device, so please read up on using this mode beforehand!!
Have Device Manager open to see what's going on with drivers
In SP Tools, load a stock ROM and tick *just* the Preloader. Hit Download.
Then hold down *only* the Volume + key (keep it pressed!) and plug the phone in. This bypasses the higher functions of the phone's memory and loads a basic driver - Mediatek USB VCOM will appear in the Device Manager under Ports. Keep Vol + pressed and it will flash the Preloader part of the memory.
With the Preloader flashed, the other parts of the phone (such as recovery) should be flashable, as hopefully the preloader driver will now load.
Brilliant, it´s working now. Thanks a lot.
[Solved] Bricked -Brom Protocol Error- during flashing recovery with SP Flash Tool
tldr; Doing nothing fixed my phone
In my case, I received a "Brom Protocol Error" during the flashing of a recovery with SP Flash Tools. Phone was bricked, didn't turn on anymore.
When connecting to my pc, I would see "USB VCom Driver" be active but whatever I tried, SP Flash Tools would never start flashing again. The phone also never activated the "USB preloader Driver". Trying to get to meta-mode with connecting USB while pressing Volume+ didn't work either.
Solution worked out to be : Let the phone drain its battery. Over a few days I had removed the back cover and had been watching YouTube-movies about shorting test-points, the phone laying on my desk not charging. Right before I desoldered the battery I connected the phone again and pfew : It went to "USB Preloader Driver" and I could flash again
Connect to P9000, YES
Was completely lost on how to flash a new ROM to the phone. Have used SP Flash many times before. Without knowing the +Volume trick was completely lost. Wasted weeks on this. Thank you alohahe3000.
nephster said:
Having just gone through the joy of unbricking my new P9000, after I didn't untick preloader when flashing, I've learned more today about using "meta-mode" with a MediaTek phone than I ever wanted to!
This is what debricked my phone. I wonder if this is of use to you? I make no claims it won't brick your device, so please read up on using this mode beforehand!!
Have Device Manager open to see what's going on with drivers
In SP Tools, load a stock ROM and tick *just* the Preloader. Hit Download.
Then hold down *only* the Volume + key (keep it pressed!) and plug the phone in. This bypasses the higher functions of the phone's memory and loads a basic driver - Mediatek USB VCOM will appear in the Device Manager under Ports. Keep Vol + pressed and it will flash the Preloader part of the memory.
With the Preloader flashed, the other parts of the phone (such as recovery) should be flashable, as hopefully the preloader driver will now load.
Click to expand...
Click to collapse
Didn't appear
nephster said:
Having just gone through the joy of unbricking my new P9000, after I didn't untick preloader when flashing, I've learned more today about using "meta-mode" with a MediaTek phone than I ever wanted to!
This is what debricked my phone. I wonder if this is of use to you? I make no claims it won't brick your device, so please read up on using this mode beforehand!!
Have Device Manager open to see what's going on with drivers
In SP Tools, load a stock ROM and tick *just* the Preloader. Hit Download.
Then hold down *only* the Volume + key (keep it pressed!) and plug the phone in. This bypasses the higher functions of the phone's memory and loads a basic driver - Mediatek USB VCOM will appear in the Device Manager under Ports. Keep Vol + pressed and it will flash the Preloader part of the memory.
With the Preloader flashed, the other parts of the phone (such as recovery) should be flashable, as hopefully the preloader driver will now load.
Click to expand...
Click to collapse
Mediatek USB VCOM didn't appear. Instead, "unkown device" appeared under "other devices". Can someone help me because I'm about to finish flashing my Tablet and it's Nextbook 7 Premium. Thanks a lot!
nephster said:
Having just gone through the joy of unbricking my new P9000, after I didn't untick preloader when flashing, I've learned more today about using "meta-mode" with a MediaTek phone than I ever wanted to!
This is what debricked my phone. I wonder if this is of use to you? I make no claims it won't brick your device, so please read up on using this mode beforehand!!
Have Device Manager open to see what's going on with drivers
In SP Tools, load a stock ROM and tick *just* the Preloader. Hit Download.
Then hold down *only* the Volume + key (keep it pressed!) and plug the phone in. This bypasses the higher functions of the phone's memory and loads a basic driver - Mediatek USB VCOM will appear in the Device Manager under Ports. Keep Vol + pressed and it will flash the Preloader part of the memory.
With the Preloader flashed, the other parts of the phone (such as recovery) should be flashable, as hopefully the preloader driver will now load.
Click to expand...
Click to collapse
I know this was a LONG time ago, but after spending two days trying so many things to save my p9000 this finally did it. Thank you VERY much!
Wonderful I only had the Elephone a few days, mine had a very temperamental SIM slot and I couldn't get NFC to work for anything useful. A shame, as it had lots of potential, I thought. Glad you are getting your money's worth out of your one!
Hello, guys.
Recently, I've tried to root a Cubot Power 4G following a guide I found online. I probably should have been more catious about it, cause now the phone is stuck on a bootloop. I tried to install a custom recovery to try and fix this, but as there was no official twrp for Cubot, I once again downloaded something that was probably shady. Thus, now the phone is stuck on bootloop, won't access recovery mode, is now turned off because battery gave out, but if I try to connect it to the pc, it will start to bootloop again. I cannot access adb, or at the least I don't know a way to, since it keeps bootlooping and I have no way to access a recovery mode(since there's no one, or at the least, if there is, it's faulty). What can I do here?
@Giordyman
Re-flash phone's Stock ROM by means od MTK Flash Tool. You have to install the Mediatek VCOM drivers before on your Windows computer, if not done yet.
jwoegerbauer said:
@Giordyman
Re-flash phone's Stock ROM by means od MTK Flash Tool. You have to install the Mediatek VCOM drivers before on your Windows computer, if not done yet.
Click to expand...
Click to collapse
I did! Or so I think... The moment I connect it to the pc, it starts bootlooping and so the pc cannot actually connect there
Bootloop is a situation where you cannot get into the "normal" Android system. Take note that as soon Android logo is shown on phone's display Android kernel got successfully initialized, ADB & Fastboot are ready.