I tried to change the Chinese Firmware to Global firmware to (Meizu Pro 7) and now I have a problem.
I followed this guide on this web:
chinahandys .net (I can't copy the link here since I have a new user
and so I deleted the file "boot.img"
I also couldn't open the Update.zip file with Winrar or another archive program.
then, I tried to do this :
"10. In FlashFire, select the small plus icon at the bottom right and select “Flash ZIP or OTA”. Select the “update.zip” file and confirm the pop-up with the tick at the top right"
but I couldn't find the “update.zip” file there.
finally, I tried to open the update.zip by pressing "Update".
since then my phone won't start.
The only thing i can do is pressing the "plus" button and another button below which will lead to me to a screen of Updating the system. when I try to do it's wrong because "firmware not found".
My phone is stock on the screen "flyme".
please help me!! I just bought this phone
(danhdongufixer) he is on Facebook.... He single handily brought my pro 7 plus back from the dead get ahold of him he's wizard .
I had same problem and this guy fixed my phone get in touch with him because there is nothing else you can do meizu left a lot of us hanging for over 3 months and no help . Good luck
You maybe don't use the good Firmware
maorsah said:
I tried to change the Chinese Firmware to Global firmware to (Meizu Pro 7) and now I have a problem.
I followed this guide on this web:
chinahandys .net (I can't copy the link here since I have a new user
and so I deleted the file "boot.img"
I also couldn't open the Update.zip file with Winrar or another archive program.
then, I tried to do this :
"10. In FlashFire, select the small plus icon at the bottom right and select “Flash ZIP or OTA”. Select the “update.zip” file and confirm the pop-up with the tick at the top right"
but I couldn't find the “update.zip” file there.
finally, I tried to open the update.zip by pressing "Update".
since then my phone won't start.
The only thing i can do is pressing the "plus" button and another button below which will lead to me to a screen of Updating the system. when I try to do it's wrong because "firmware not found".
My phone is stock on the screen "flyme".
please help me!! I just bought this phone
Click to expand...
Click to collapse
Hi,
For 3 month, I hope you have find the solution. If you don't, here is mine :
I had the same problème on my phone.
I couldn't reinstall it, I think the version that I downloaded wasn't compatible with the "Chinese" version of my mobile.
You need to find the good firmware !
Could you try with this chinese firmware : MEIZU PRO7 Standard Version -Flyme6.1.3.2A-7.0
It's worked on my phone.
So,
Press and hold the volume up and power button until the screen goes on recovery mode.
Connect the device to the laptop or PC, you can open the device. You will see an empty partition named recovery.
Now copy the downloaded firmware of your phone and place it in the recovery partition. Just copy update.zip to recovery partition.
Now in the phone select update firmware and clear data and press next.
The phone will reboot and install the firmware.
Wait, wait, wait 15mn be patient.
tell me if it's working on your phone.
excuse me for my poor English !
Math32 said:
Hi,
For 3 month, I hope you have find the solution. If you don't, here is mine :
I had the same problème on my phone.
I couldn't reinstall it, I think the version that I downloaded wasn't compatible with the "Chinese" version of my mobile.
You need to find the good firmware !
Could you try with this chinese firmware : MEIZU PRO7 Standard Version -Flyme6.1.3.2A-7.0
It's worked on my phone.
So,Press and hold the volume up and power button until the screen goes on recovery mode.
Connect the device to the laptop or PC, you can open the device. You will see an empty partition named recovery.
Now copy the downloaded firmware of your phone and place it in the recovery partition. Just copy update.zip to recovery partition. Now in the phone select update firmware and clear data and press next.
The phone will reboot and install the firmware.
Wait, wait, wait 15mn be patient.
tell me if it's working on your phone.
Click to expand...
Click to collapse
Hello!
Was everything, such as google playstore and english language, still working on you phone after you updated the firmware?
I was also wondering if theres need to backup the IMEI somewhere?
Im currently running a modified verision of 6.1.3.2A which doesnt have all the features for the 2nd display and hence looking for an upgrade.
Leone1 said:
Hello!
Was everything, such as google playstore and english language, still working on you phone after you updated the firmware?
I was also wondering if theres need to backup the IMEI somewhere?
Im currently running a modified verision of 6.1.3.2A which doesnt have all the features for the 2nd display and hence looking for an upgrade.
Click to expand...
Click to collapse
I used this chinese version less than 10mn. I would advise you to install the G firmware !
I didn't install the playstore (too thing in chinese in this firmware) that's why after running the version 6.1.3.2A, i used this tutorial :
https://forum.xda-developers.com/showpost.php?p=75297402&postcount=70
"Download the firmware Flyme 6.1.3.2G from here
http://www.flymeos.com/firmwarelist?modelId=88&type=1
after you can do the instructions in video
https://www.youtube.com/watch?v=aDp6oZL4Wx4 "
Be careful when you install superSU to do the same thing as in the video. I don't do the same than on the vidéo that's why i need to reinstall the chinese firmware. After the installation i wait 15mn and my phone stays on Flyme. i restart it and it worked for installing busybox and flashfire.
I wish you bon courage !
Math32 said:
I used this chinese version less than 10mn. I would advise you to install the G firmware !
I didn't install the playstore (too thing in chinese in this firmware) that's why after running the version 6.1.3.2A, i used this tutorial :
https://forum.xda-developers.com/showpost.php?p=75297402&postcount=70
"Download the firmware Flyme 6.1.3.2G from here
http://www.flymeos.com/firmwarelist?modelId=88&type=1
after you can do the instructions in video
https://www.youtube.com/watch?v=aDp6oZL4Wx4 "
Be careful when you install superSU to do the same thing as in the video. I don't do the same than on the vidéo that's why i need to reinstall the chinese firmware. After the installation i wait 15mn and my phone stays on Flyme. i restart it and it worked for installing busybox and flashfire.
I wish you bon courage !
Click to expand...
Click to collapse
Ah ok, so you only used it to be able to flash the global rom on?
Ive read multiple places that its not possible to update from A to G, thats why i was thinking about going to the 7.0.0.0A ROM instead. The shop i bought it from (CECT, who are not very well informed at all) told me it would brick the phone to go to G from A, my phone is apparently not intended for global sale thats why they make their own version and flashes it on...
So now im just looking for someone who can confirm that updating to the A-rom wont remove google play or english.
EDIT: I have the Helio P25 model
Related
Hallo everyone.
I have just tried to follow this guide to install Google Play and so on: http://forum.xda-developers.com/showthread.php?t=2256075
Guide:
I'm here for help you, and yes I bought K900
Here is the international .inb file to flash.
Part One: How flash international version:
1. create SDFUSE folder in the / of sdcard.
2. insert inb file there
3. go to fastboot mode (Vol+ + Power) and choose sdfuseupdate
4. done.
you'll get official international 47 rom (ROW region). It has google apps, it has play store.
INB file is here:
https://mega.co.nz/#F!xNdywAJA!AFbE_HikuoFODLpoc1j7Yg
But right after the message saying SDCARD UPDATE COMPLETED (as i remember it), the phone wont start again. The three buttons on the front flashes and nothing else happens.
Any clues to what might be the problem?
I hope you can help me!
Best regard
Jonas Kristiansen
Question
Hi Jonas,
Sorry to hear that.
Did you totally brick your phone? Can you still go into recovery or Hboot?
Is your phone recognized by adb and fastboot?
If you tell me more, maybe I can help.
Denis
Jonas Kristiansen said:
Hallo everyone.
I have just tried to follow this guide to install Google Play and so on: http://forum.xda-developers.com/showthread.php?t=2256075
Guide:
I'm here for help you, and yes I bought K900
Here is the international .inb file to flash.
Part One: How flash international version:
1. create SDFUSE folder in the / of sdcard.
2. insert inb file there
3. go to fastboot mode (Vol+ + Power) and choose sdfuseupdate
4. done.
you'll get official international 47 rom (ROW region). It has google apps, it has play store.
INB file is here:
https://mega.co.nz/#F!xNdywAJA!AFbE_HikuoFODLpoc1j7Yg
But right after the message saying SDCARD UPDATE COMPLETED (as i remember it), the phone wont start again. The three buttons on the front flashes and nothing else happens.
Any clues to what might be the problem?
I hope you can help me!
Best regard
Jonas Kristiansen
Click to expand...
Click to collapse
Same problem
Hello
I have same problem, i brick my K900. I try to start it, but phone is really little ignorant, absolutly not response to all. Flash using xFSTK is without chance.
Yep, Recovery and DroidBoot is unavilable. Phone only one flash touch buttons and nothing more... :crying:
Can you help me? I thing, hard-brick is too hard to solve.
Sorry for my english...
Maybe it will be usefull:
Volume down, hold it, then power button, Testing Menu appear, Droidboot, Recovery, Clear cache, Clear data (factory reset), reboot.
how unbrick ur k900 device
Jonas Kristiansen said:
Hallo everyone.
I have just tried to follow this guide to install Google Play and so on: http://forum.xda-developers.com/showthread.php?t=2256075
Guide:
I'm here for help you, and yes I bought K900
Here is the international .inb file to flash.
Part One: How flash international version:
1. create SDFUSE folder in the / of sdcard.
2. insert inb file there
3. go to fastboot mode (Vol+ + Power) and choose sdfuseupdate
4. done.
you'll get official international 47 rom (ROW region). It has google apps, it has play store.
INB file is here:
https://mega.co.nz/#F!xNdywAJA!AFbE_HikuoFODLpoc1j7Yg
But right after the message saying SDCARD UPDATE COMPLETED (as i remember it), the phone wont start again. The three buttons on the front flashes and nothing else happens.
Any clues to what might be the problem?
I hope you can help me!
Best regard
Jonas Kristiansen
Click to expand...
Click to collapse
(my english is veryyyyyyyyyy bad)
dont worry . there is a simple method :
this method work for hardbrick and softbrick too.
first download a favorite Rom you want
u can choice ur Rom from this page : http://m.kaskus.co.id/post/5300581ffbca17d47b8b457c#post5300581ffbca17d47b8b457c
download and install manufacturing flash tool and intel android device usb driver
https://dl.dropboxusercontent.com/u/26833962/K900 Tools/ManufacturingFlashTool_Setup_6.0.2.exe
http://software.intel.com/en-us/android/articles/intel-usb-driver-for-android-devices
second Refer this : http://forum.xda-developers.com/show...postcount=3245
This method require computer with driver and software installed and USB cable for sure
( unzip ur rom and open xml file on ur rom with manufacturing flash tool softwre)
maybe this video can help you too :
https://www.youtube.com/watch?v=BhvA_T694kw
This method works on my hardbrick device succeesfully
tatu63 said:
(my english is veryyyyyyyyyy bad)
dont worry . there is a simple method :
this method work for hardbrick and softbrick too.
first download a favorite Rom you want
u can choice ur Rom from this page : http://m.kaskus.co.id/post/5300581ffbca17d47b8b457c#post5300581ffbca17d47b8b457c
download and install manufacturing flash tool and intel android device usb driver
https://dl.dropboxusercontent.com/u/26833962/K900 Tools/ManufacturingFlashTool_Setup_6.0.2.exe
http://software.intel.com/en-us/android/articles/intel-usb-driver-for-android-devices
second Refer this : http://forum.xda-developers.com/show...postcount=3245
This method require computer with driver and software installed and USB cable for sure
( unzip ur rom and open xml file on ur rom with manufacturing flash tool softwre)
maybe this video can help you too :
https://www.youtube.com/watch?v=BhvA_T694kw
This method works on my hardbrick device succeesfully
Click to expand...
Click to collapse
hi tatu63
Me too got my K900 bricked while updating Rom from MFT .
Its not starting anymore. Complete black screen no menu lights at all.
When i connect my phone to usb cable it shows this in MFT tool and hangs up
07/01/14 12:47:15.886 DEBUG : New Android device -> serial: MedfieldEC710F76 status: 0 port: 1
and
Hi there
i have alcatel pixi 7 (i213)
i root it then backuped with MtkDroidtools
now i want to install recovery cwm BUT
my recovery size is 16 mb
im unpacking - repacking stock recovery but after flashing its even not booting
flashing recovery 16 mb and its booting
after repack it is 5-6 mb
i think its uses other pack method
help PLS
blabla
if someone needs...
stock recovery : https://mega.co.nz/#!G4kDkJpL!CH3oWWqDm_6rDLGlHgoOISvg-jd436FXnNkdtCboGh0
CTRecovery_2.5 : https://mega.co.nz/#!jh82HKoR!D-BbITkkfHqMNy6hewgCLV_7Xw9xZJoX8YfezwqHpKQ
Hi!
I have bricked my pixi 7 (i213). After root i have started debloating stock firmware and misstyped some command and of course i didn't made a copy.
If anyone could upload and share custpack and system (android) images/partitions or whole stock firmware it would be great.
Xcore_Rj said:
if someone needs...
stock recovery : https://mega.co.nz/#!G4kDkJpL!CH3oWWqDm_6rDLGlHgoOISvg-jd436FXnNkdtCboGh0
CTRecovery_2.5 : https://mega.co.nz/#!jh82HKoR!D-BbITkkfHqMNy6hewgCLV_7Xw9xZJoX8YfezwqHpKQ
Click to expand...
Click to collapse
whats that custom recovery for?
is it compatible with my zeki quad core 4.4.2 android tablet?
i need one!! :fingers-crossed:
hmmm
emm
download mobile upgrade
here's the link http://www.alcatelonetouch.com/glob...n/PIXI_7/otu/mobile-upgrade-s-4-1-8-setup.exe
open it
select pixi 7 or i213
and follow steps
contact if any problems
glad to help
Sent from my I213 using XDA Free mobile app
Thanks for the reply.
Mobile upgrade pops up message that there is no new firmware for my tablet. I think its stock fw wasn't from alcatel. It's custom made by Orange telecomunication company ... don't know what to do next .
Marcin Tomczczyk said:
Thanks for the reply.
Mobile upgrade pops up message that there is no new firmware for my tablet. I think its stock fw wasn't from alcatel. It's custom made by Orange telecomunication company ... don't know what to do next .
Click to expand...
Click to collapse
mine is from orange too..but its updating...
so i can give my system.img..its already rooted..try so..
https://onedrive.live.com/?cid=b84e72ba94787c35&id=B84E72BA94787C35%211315&ithint=file,img&authkey=!ACvvZMgyUIoS2rU
if after flashing it will not boot flash boot.img too https://mega.co.nz/#!T80ihQAA!wiofxhYpc_5sfrKpUYIINSU-Vzb7vFqENI1EbaPyT-0
Thanks for the upload, share and help!
I was talking about polish part of the Orange corporation, not the international one. So this might be the answer why mobile upgrade not updating my tablet firmware . They don't give a f... .
Also still not booting after flashing system and boot images.
Does your firmware have custpack partition? It is partition with stock apk's and other stuff from alcatel. I was deleting packages from this partition also.
I know i'm asking a lot but if your firmware does have this partition, could you also upload it?
Could you also upload custpack partition? I have no other way to unbrick this tablet .
zzzz
Is this compatible with my l212? I think its not. Can you check my Dump System? If we are the same partition then i can flash that.
How to root?
Hello everybody.
I bought the tablet, and try to find a way to root it.
All the tools I found didn't make the job...
How do you root your device?
Thanks for your support!
Greetings
ThMusch said:
I bought the tablet, and try to find a way to root it.
All the tools I found didn't make the job...
How do you root your device?Greetings
Click to expand...
Click to collapse
I Had some problems with rooting this piece of crap the conventional way, but I managed to do it using iRoot. The bad thing is that iRoot's SU app will keep installing a lot of useless stuff in Chinese. To get rid of them, you first need to install SuperSU from the Play Store (If I recall correctly CWM Superuser will work fine as well, but ChainsDD Superuser won't, so keep this in mind) after rooting it and then using manually remove the Chinese SuperUser apk that comes with iRoot and once you get rid of it, you can uninstall the remaining Chinese apps the normal way.
Marcin Tomczczyk said:
Could you also upload custpack partition? I have no other way to unbrick this tablet .
Click to expand...
Click to collapse
I am in the middle of unbricking my Pixi 7 after failed installation of fonts (my font folder CHMOD got messed up and now the device is not booting as it can't reed it), and if I success, I'll post here about the process.
@edit
Okay, if anyone ever has problem with recovering their Pixi 7, here are the steps to make a clean installation using Mobile Upgrade S. The only requirement is to have the device already installed on at least one of your USB ports (otherwise your OS won't detect it, as it will try to install the drivers, but will fail because it sees the device to be disconnecting shortly after plugging it in – at least it was my case):
1. Download Mobile Upgrade S and SP Flash
2. Grab this scatter file.
3. Open the file you just downloaded. Find the following section:
...
partition_index: SYS3
partition_name: PRO_INFO
file_name: NONE
is_download: false
...
Click to expand...
Click to collapse
And replace is_download to true;
4. Open Flash tool and in your download section select your edited scatter file.
5. Go to Readback and select Add.
6. Double-click the added line and save it as pro_info.img
7. Set it as follows: Type : hex , Region EMMC_USER , start : 0x100000 , lenght 0x300000
8. Click Read Back, turn off your Pixi and connect it to your PC via USB cable. It should start the read immediately and after few seccond you should get a success messgae. If it's not the case, try a different USB port.
9. After you got your read, disconnect your Pixi and open newly created pro_info.img file in a hex editor.
10. Find your device version (it's soimewhere at the beggining, around adress 0xA3, and looks like XXXI213-XXXXXXX, where X can be any character, for example mine was COXI213-2DRGPL1) and change it to ENXI213-2BALGB1.
11. Replace your software version (Right after your device ver. Mine was AAZY1AAZ0Z0BD00) for AAZY1AAY0Y0BD00.
12. Save changes to your file.
13. Go back to your SP Flash tool > Download tab
14. Select your scatter file. Deselect all checkboxes. Leave PRO_INFO checked only.
15. Click on PRO_INFO location and select the file you just edited.
16. Select Download and connect your Pixi.
17. When done, run Mobile Upgrade S and follow the standard upgrading process (be aware, that it will take a lot of time to download the ROM, as the download speed goes around 20-50 KB/s. It took me aroung 8h to download it).
18. After installation run your Pixi for the first time and wait for it to boot (don't panic if it takes a bit of time. It will be booting for about 2-5 minutes for the first time).
Nidrax said:
I Had some problems with rooting this piece of crap the conventional way, but I managed to do it using iRoot. The bad thing is that iRoot's SU app will keep installing a lot of useless stuff in Chinese. To get rid of them, you first need to install SuperSU from the Play Store (If I recall correctly CWM Superuser will work fine as well, but ChainsDD Superuser won't, so keep this in mind) after rooting it and then using manually remove the Chinese SuperUser apk that comes with iRoot and once you get rid of it, you can uninstall the remaining Chinese apps the normal way.
I am in the middle of unbricking my Pixi 7 after failed installation of fonts (my font folder CHMOD got messed up and now the device is not booting as it can't reed it), and if I success, I'll post here about the process.
@edit
Okay, if anyone ever has problem with recovering their Pixi 7, here are the steps to make a clean installation using Mobile Upgrade S. The only requirement is to have the device already installed on at least one of your USB ports (otherwise your OS won't detect it, as it will try to install the drivers, but will fail because it sees the device to be disconnecting shortly after plugging it in – at least it was my case):
1. Download Mobile Upgrade S and SP Flash
2. Grab this scatter file.
3. Open the file you just downloaded. Find the following section:
And replace is_download to true;
4. Open Flash tool and in your download section select your edited scatter file.
5. Go to Readback and select Add.
6. Double-click the added line and save it as pro_info.img
7. Set it as follows: Type : hex , Region EMMC_USER , start : 0x100000 , lenght 0x300000
8. Click Read Back, turn off your Pixi and connect it to your PC via USB cable. It should start the read immediately and after few seccond you should get a success messgae. If it's not the case, try a different USB port.
9. After you got your read, disconnect your Pixi and open newly created pro_info.img file in a hex editor.
10. Find your device version (it's soimewhere at the beggining, around adress 0xA3, and looks like XXXI213-XXXXXXX, where X can be any character, for example mine was COXI213-2DRGPL1) and change it to ENXI213-2BALGB1.
11. Replace your software version (Right after your device ver. Mine was AAZY1AAZ0Z0BD00) for AAZY1AAY0Y0BD00.
12. Save changes to your file.
13. Go back to your SP Flash tool > Download tab
14. Select your scatter file. Deselect all checkboxes. Leave PRO_INFO checked only.
15. Click on PRO_INFO location and select the file you just edited.
16. Select Download and connect your Pixi.
17. When done, run Mobile Upgrade S and follow the standard upgrading process (be aware, that it will take a lot of time to download the ROM, as the download speed goes around 20-50 KB/s. It took me aroung 8h to download it).
18. After installation run your Pixi for the first time and wait for it to boot (don't panic if it takes a bit of time. It will be booting for about 2-5 minutes for the first time).
Click to expand...
Click to collapse
Great to hear that my instructions helped you and good that you posted it here http://forum.android.com.pl/topic/211918-stock-rom-do-pixi-7/?p=3776346
KINGROOT 4.5.2 works for my pixi7 (i213)
Code:
**** DISCLAIMER ****
This post is an EXPERT-LEVEL Post.
I am NOT RESPONSIBLE for what you do to your device.
Please not that I am still working on a solution to this brick.
Hello XDA-Developers,
I recently got my hands on a Meizu M3 note and, of course, wanted the newest - nougat - firmware on it. It seems I accidently flashed a incompatible (or currupted) Update (flashed an A Firmware on a G version phone). Sadly it broke down and showed only vertical stripes on it's display.
Image here: https://ibb.co/cpGunm
After some hours research I found some information on how to reflash the M3 note via SP Flash Tool here and here. Since the first tutorial is for the M3 and M3s and the second tutorial is for the M model of the device (I've got the L model) there are some changes needed for it to somehow magically work.
I exchanged files provided (such as preloader.bin, lk.bin etc) with the matching ones from the latest Official Global Firmware from Meizu. Just extracted them out of the update.zip. (Don't forget to select the Authentication File!)
Image here: https://ibb.co/k3zYDR
Short flashing tutorial: make sure your device is turned off and disconneced then click "Download" and connect your device via USB. Don't worry if it now shows an error like "Download DA Failed", just dismiss the error and click "Download" again. It should flash the device now.
Sadly it is not possible to flash the boot.img provided in the latest official update.zip from Meizu (you'll get an security mismatch error). BUT the boot-verified.img provided by the chinese archive is flashable and is accepted by the device. The device is now in a bootloop, fastboot is accessible via holding Vol - and Power, but no recovery access via Vol+ and Power
The files seem to be repaired now but the display still shows these stripes - I think the firmware actually fried something on the display chipset. I bought a replacement screen and then will update this thread as soon as possible. If you have any Ideas of how to unbrick the device feel free to discuss.
Update 18.11.2017
Thanks to @ncristian !
I did as he suggested, downloaded and flashed the files from the russian forum here (if you do not speak russian and want to get straight to the point: Direct Download Link)
I still have the stripes on my screen but the device booted up successfully and got recognized again by my computer! While booting up I could see the stripes changing their color slightly as the bootanimation of flyme was playing. I guess I will have to replace the screen to make the display error go away... I will update this post as soon as I did so
Update 10.11.2018
Sadly I never actually exchanged the screen, I'm running a Pro 7 Plus as a daily driver now and I'm loving it
Update 19.05.2019
I have attached the boot-verified.img as someone requested it
I had the same problem and I solved thanks to this: https://4pda.ru/forum/index.php?showtopic=739028&st=24480#entry65580668 and Google Translate; I downloaded the .zip, installed drivers, launched the flash tool and flashed files contained in the folder L691H (Remember to install drivers and disable antivirus or it will not work). Then I downloaded FlyMe 6.1.0.0G, went into recovery with vol up + power, copied the update.zip into the device "Recovery" and flashed it; the only problem I had is that the phone charged but he didn't recognize the battery level; by reflashing the files contained in the 4pda .zip, the battery level went up (obviously, after leaving the phone charging for about an hour).
Someone please help my meizu m3 note bricked after flashing flyme 7.8 beta.
Rajdas26 said:
Someone please help my meizu m3 note bricked after flashing flyme 7.8 beta.
Click to expand...
Click to collapse
Try reflashing via the original recovery, that might be your easiest solution. If that doesn't work you might try your luck with something like SP flash tool
Hey. Uhmm i know it's an olld post but i'm hopeless now. I need the boot-verified img you have. i can't find it anywhere. can you send it to my gmail ?? [email protected]
shawn_mendes said:
Hey. Uhmm i know it's an olld post but i'm hopeless now. I need the boot-verified img you have. i can't find it anywhere. can you send it to my gmail ?? [email protected]
Click to expand...
Click to collapse
I have attached the file to the first post. Good thing I never delete anything :angel:
m3shat said:
I have attached the file to the first post. Good thing I never delete anything :angel:
Click to expand...
Click to collapse
First of all, thank you mate I successfully downloaded the boot verified. But still it didn't turned on. Just no power but recognized by the sp tool. I'm starting to think that downloaded again the wrong firmware. I also found out that their are two main board(or whatever is that). So this global firmware can be flashed in the both L and M series. I'm wondering what firmware you used to flash. Again, thank you in advance ^_^
l got same problem .. (because I'm not read careful )l tired to flash using many firmware or using boot verified .. i tired that for 2 Days.. So l give up.. take my device to profesional service . and solved. solved with Emmc repair ..
my device is L681H.
SORRY WAS INACTIVE FOR SOMETIME... NOW IM BACK YOU CAN ASK AGAIN...
ALL CHIPSETS UNBRICKING METHOD HAS BEEN POSTED
Hi you may ask me anything related to android and I promise to answer within 24 hours and m reply will definitely work for you.
*****************************************************
SPECIALIST IN ROOTING, DEVELOPMENT, HACKING, SECURITY BYPASS, RECOVERY, FLASHING, CUSTOM ROM'S
*****************************************************
SEE YOU SOON
*****************************************************
•NOT RESPONSIBLE FOR ANY DAMAGE CAUSED TO YOUR DEVICE•
LG Aristo v10g Metropcs
How do i start configuring this phone without a google account?
A friend who was using it gave me this phone but forgot the boot password and the google account was not of him. So, now, we can´t use the phone.
Mephis96 said:
How do i start configuring this phone without a google account?
A friend who was using it gave me this phone but forgot the boot password and the google account was not of him. So, now, we can´t use the phone.
Click to expand...
Click to collapse
You mean to say that the phone is in frp mode?
(Factory reset protection)
Yes
FRP..... thanks, id did not know what it means.
Yes, it is in FRP
Mephis96 said:
FRP..... thanks, id did not know what it means.
Yes, it is in FRP
Click to expand...
Click to collapse
Can you please tell me the phone model and it's info.
LG Aristo v10g from Metropcs
x.ak**** said:
Can you please tell me the phone model and it's info.
Click to expand...
Click to collapse
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
[PC] HOW TO CURE A BRICKED M-TEK DEVICE!!
///////////////////////////////////////////////////////////////////////////////////////////
• Download and Install the Android USB drivers for your device that I have mentioned below.
• Power Off your device and remove the battery (only if it's removable)
• Download the stock ROM or the Custom ROM on your PC that you want to flash. (GIVEN BELOW)
• Download and extract SPFT (Smart Phone Flash Tool) on your PC, you will be able to see the files shown in the picture below. (Pic 1.1)
• Open Flash tool.exe (Pic 1.2)
• Once SPFT is launched tap on Download tab. (Pic 1.3)
• In download tab click on Scatter-Loading button. (Pic 1.4)
• Now locate the Scatter File that you will find in the Stock ROM folder that you downloaded in step 3. (Pic 1.5)
• Click on Download button to start the flashing process.(Pic 1.6)
• After finishing a success message will appear. (Pic 1.7)
///////////////////////////////////////////////////////////////////////////////////////////
Downloads:-
https://androiddatahost.com/b9cyw (DRIVERS)
https://spflashtool.com/download/SP_Flash_Tool_v5.1744_Win.zip (SPFT)
https://www.needrom.com/download/lenovo-s850/ (ROM FOR LENOVO S850, REGISTRATION NEEDED ON WEBSITE TO DOWNLOAD THE ROM)
///////////////////////////////////////////////////////////////////////////////////////////
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
I was working on another project that you can see below give me 1 hour I'll get back to you ASAP.
Best tool like SetCPU for controlling CPU with profiles?
SetCPU doesn't allow core control though
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
How to BYPASS FRP LOCK!
Test conducted on Virtual Machine on my PC
****************************************************************
I am not responsible for any damage you may cause to your device!
****************************************************************
****************************************************************
Never wanted to upload it but did it because I aim at helping people.
****************************************************************
Google FRP (factory reset protection) is aimed at making a stolen phone less valuable.
We usually keep our phones locked with a password or pattern but once its stolen it is easy to erase the data (via Hard Reset) and reuse the phone. With Google FRP in place, whenever the phone is formatted using hardware keys it will ask for the last synced google account details before proceeding further.
///////////////////////////////////////////////////////////////////////////////////////////
Until now, everytime some sort of hack comes out to bypass this screen and then its patched with a security update very soon. Same is the case with LG Aristo. There is a working solution as of now but it may not last long. Let’s see how to get this working –
///////////////////////////////////////////////////////////////////////////////////////////
How to Bypass LG Aristo Google Account –
This process is lengthy, but it’s a sure shot method and works every time.
We need 2 apps to complete this bypass process. They are Shortcut Master Lite and Sidebar Lite. Download the zip file from below link.
DOWNLOAD
>Extract the zip file and transfer the apk files to a micro sd card. Install the SD card in your LG Aristo before proceeding further.
///////////////////////////////////////////////////////////////////////////////////////////
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
Done
Drop a like on all my replies so I can stay encouraged and help you further.
YeshYyyK said:
Best tool like SetCPU for controlling CPU with profiles?
SetCPU doesn't allow core control though
Click to expand...
Click to collapse
You may use Kernel Manager it's super useful and will do what you're asking for!
Hi ! Could you help me with my problem ?? https://forum.xda-developers.com/search.php?searchid=446201503
No one seems to be able to help me... thanks a lot!!!!
antoflos said:
Hi ! Could you help me with my problem ?? https://forum.xda-developers.com/search.php?searchid=446201503
No one seems to be able to help me... thanks a lot!!!!
Click to expand...
Click to collapse
I will definitely help you just give me one hour but can you post the following info:
Model Number:
Exact Problem:
How that problem occured:
Model Number: SM-G935F / Galaxy S7 edge
Exact Problem : I can't go back to the dock ROM
How that problem occured : Last week, I wanted to try to change my phone a SM-G935F on a custom rom " Minotaurus Oreo V10". I did it successfuly but didn't like it so much so I decided to go back to stock Rom.
I used Odin and a stock ROM for that but I think I made a big mistake by not wiping with TWRP before flashing with Odin.
It resulted that my phone was stocked on the S7 edge logo. Luckly I can go on download mode so it's not hard bricked but Odin failed on every flash I've tried. It stoped at the step "config.msi"
To flash I used this dock Rom : SM-G935F_1_20161201150115_pbdym44h2s_fac
x.ak**** said:
I will definitely help you just give me one hour but can you post the following info:
Model Number:
Exact Problem:
How that problem occured:
Click to expand...
Click to collapse
Hey man this quite difficult and i need to install this phone's firmware on my VIRTUAL Machine, basically I request you to wait for the time being so I can save your phone.
Drop a like on all my comments above to encourage me.
Huawei P10+ Firmware on Huawei P10 - by accident
Hi:
On my P10, I used Firmwarefinder for Huawei to find the firmware (Oreo with EMUI 8) and after verifying, I downloaded and upgraded the P10 to new firmware. After reboot, the dpi is seemed changed (as picture attached) and when I went to check it on about phone, it says Model is VKY (which is Huawei P10+) - picture attached.
Is there a way to rollback and install the correct firmware on this phone somehow?
antoflos said:
Model Number: SM-G935F / Galaxy S7 edge
Exact Problem : I can't go back to the dock ROM
How that problem occured : Last week, I wanted to try to change my phone a SM-G935F on a custom rom " Minotaurus Oreo V10". I did it successfuly but didn't like it so much so I decided to go back to stock Rom.
I used Odin and a stock ROM for that but I think I made a big mistake by not wiping with TWRP before flashing with Odin.
Click to expand...
Click to collapse
***********************************************************************************
I AM NOT RESPONSIBLE FOR ANY FURTHER DAMAGE THAT MAY BE CAUSED TO YOUR DEVICE...(UNLIKELY TO HAPPEN)
***********************************************************************************
For being able to make the downgrade operation you will have to use a Windows based computer on which you will then install Odin (an official program developed by Samsung and used on update types of operations).
***********************************************************************************
Download Odin on your computer; afterwards install the program by following on screen prompts.
The Samsung Galaxy S7 Edge USB drivers must be installed on your PC too – use Samsung KIES in that respect.
Download the stock / official Android OS for your S7 Edge – from SamMobile or from Samsung’s official website.
Power off your device and reboot into download mode: press and hold the Power, Volume Down and Home buttons for a few moments; then connect your phone with your computer with the help of the USB cable.
After making sure that Odin has recognized your device (the “added” message must be displayed and the ID:COM field should be turned yellow or blue) from the program select the PA option.
Load the firmware file; don’t select the Re Partition and Auto Reboot options; click on Start when done.
Wait while your SGS7 Edge is being updated; when done, remove the USB cord and reboot your phone.
For further info related to the update process reply to my thread
LIKE ALL MY COMMENTS TO ENCOURAGE ME TO HELP YOU.
xironimoh said:
Hi:
On my P10, I used Firmwarefinder for Huawei to find the firmware (Oreo with EMUI 8) and after verifying, I downloaded and upgraded the P10 to new firmware. After reboot, the dpi is seemed changed (as picture attached) and when I went to check it on about phone, it says Model is VKY (which is Huawei P10+) - picture attached.
Is there a way to rollback and install the correct firmware on this phone somehow?
Click to expand...
Click to collapse
No pictures attached!! and yes you can roll back to the stock ROM or even customize the DPI according to your phone [ROOT REQUIRED]
Let me know which one you prefer?
Also like all my comments above to encourage me to help you even faster.
Hello everyone. A couple of days ago, I bricked my huawei mate 10 pro BLA-AL00 by flashing the wrong firmware. After a few days of experimentation, I was able to revive the phone by flashing the board software back onto the phone. Now the problem is that I am on a super early build of emui and it seems like its the stock factory software with a bunch of debugging programs on it. I am having some trouble updating the firmware to android 8. I downloaded this exact firmware file: https://androidhost.ru/bzx
I am having some trouble figuring out what files I need to flash. There is a main dload folder after extracting the files, but if I try to copy that onto a usb drive and flash it using the dload method, my phone will once again brick itself. I have tried flashing the all_cn firmware file using TWRP recovery, but that also bricks my device and puts it into a bootloop. I have also tried using the huawei update file extractor software and tried manually flashing the firmware using fastboot commands, but once again will just end up in a bootloop. Am i doing something wrong? I would really appreciate any help. Thanks
Hi,
I'm in the exactly same case. Did you manage to fix it?
iBen68 said:
Hi,
I'm in the exactly same case. Did you manage to fix it?
Click to expand...
Click to collapse
I finally managed to figure everything out after days of research and testing. You must download the BLA-AL00 8.1.0.351 full ota firmware from pro-teammt.ru and extract the update.zip folder. Next, I used MRT Dongle 3.19 cracked to flash the firmware. https://www.gadgetsdr.com/mrt-dongle-latest-crack/ To activate the program, you must use the keygen provided to generate a activation code after pasting in your device id. The device id can be found by opening the mrt program for the first time. Paste in the activation code found by the keygen into the activator and the program should open. Next, click on hw flasher and put your phone into fastboot mode. Make sure your bootloader is unlocked. I assume it is unlocked as you only flashed the board firmware. Under write flash click on the 3 dots near the bottom of the page, select the update.app file you extracted before, and click on start. Don't worry if it says fail for the first few commands. It should successfully flash everything else. Once this process is finished, your phone should reboot. We need to do one final step and write the oeminfo back into the phone. Put your phone back into fastboot mode by plugging in your phone and holding down the power and volume down buttons. In MRT, click on update hw soft_ver, select huawei mate 10 pro, and click on start. After flashing, your phone should reboot normally now into an operating system!!!
Thank you for your answer ! My Mate 10 Pro is BLA-L09, how did you know you have to use this specific firmware (BLA-AL00 8.1.0.351 full ota firmware) for your BLA-AL00? I guess I should use BLA-L09 full ota but which version?
iBen68 said:
Thank you for your answer ! My Mate 10 Pro is BLA-L09, how did you know you have to use this specific firmware (BLA-AL00 8.1.0.351 full ota firmware) for your BLA-AL00? I guess I should use BLA-L09 full ota but which version?
Click to expand...
Click to collapse
It took me a very long time and a large amount of downloading to figure out the exact firmware I needed to use. I just downloaded a bunch of version and see if it would flash onto my phone. Finally, the 8.1.0.351 firmware worked! For the bla-l09, im not too sure the exact version needed. I would experiment around and try a bunch of different full ota firmware from pro-teammt.ru Maybe you could flash the bla-al00 firmware and rebrand the phone? Im not too familiar with rebranding, but I know its possible.
I have tried with BLA-L09 8.0.0.115 firmware then my phone has reboot in a better factory version (EMUI 8 instead of EMUI 5), but still in factory mode, with the developpers apps. I've done the hw soft_ver update, but it still boot on this factory version. I've tried to flash another firmware (still BLA-L09 but another version), and now my phone stays shut down. I cannot even see it on my COM port. I've tried to use test point, I can hear the USB plug computer song but nothing happen. Phone no detected, black screen, no vibration. I've tested all the possible key combinaison (volume up, volume down, power button), still nothing .
Any idea of a last chance?
I was so close thank to your help!