This mod enables the Earpiece speaker to be used at the same time with the main rear speaker when using listening to music, and watching videos etc...
Updated
Now TRUE STEREO with Earpiece playing the LEFT channel and rear speaker playing the RIGHT channel. Test with app of your choice.
Click to expand...
Click to collapse
To install open the zip file and extract the "default_gain.conf" file and copy it to "/system/etc/default_gain.conf" using your preferred method.
Then set permissions to rw-r-r or 0644 ( e.g "chmod 0644 /system/etc/default_gain.conf" ) and REBOOT your device.
Volume levels are pushed to maximum possible without distortion with EQ on Earpiece speaker to remove low frequencies. Good luck.
Works on my SM-910K running MarshMallow 6.0.1.
WARNING!!!
THIS HAS ONLY BEEN TESTED ON THE DEVICE MENTIONED ABOVE. MAKE SURE TO BACKUP YOUR DEFAULT "default_gain.conf" FILE BEFORE INSTALLING THE NEW ONE.
(E.g "adb pull /system/etc/default_gain.conf [safe location here]" or "adb shell cp /system/etc/default_gain.conf /sdcard/default_gain.conf.bak" )
To be SAFE DO a NANDroid backup in Recovery.
Happy modding.
NOTE:
If you cannot find "/system/etc/default_gain.conf" file on your device then this MOD will NOT WORK for you. If that is the case you can try the other surround mods for other variants of the Note 4. This has only been tested to work on the N910K.
I created this one because the mods for the other variants didn't work on my phone since it uses the "default_gain.conf" file instead of the 'normal' "mixer_paths.xml" file.
Source
https://github.com/salvenose/dual_mod
Changelog
v1 -> Initial Dual Speaker Mod
v2 -> Upgrade to true stereo
v3 -> Fix for audio leak through earpiece while Headphone connected
Tried it on my N910F running 6.0.1 and seems like it works,but need to cover the main speaker to hear anything from the earpiece.
alexetna95 said:
Tried it on my N910F running 6.0.1 and seems like it works,but need to cover the main speaker to hear anything from the earpiece.
Click to expand...
Click to collapse
If there was a quick ON/OFF toggle you would notice that it makes quite a difference than with it turned off completely. Especially when you receive a notification etc... with your phone lying on a flat surface.
I haven't yet figured out how to manipulate the EQ settings for the front earpiece so that it only outputs mid-treble range without any bass.
Once I do, I'll be able to boost the volume without causing distortion. Otherwise it might damage the earpiece.
Where shoud I found that toogle ?
Actually I didn't find a "default_gain.conf" file in etc,so I just simply copied the one from your mod zip.
alexetna95 said:
Where shoud I found that toogle ?
Actually I didn't find a "default_gain.conf" file in etc,so I just simply copied the one from your mod zip.
Click to expand...
Click to collapse
If you didn't find a "default_gain.conf" file then the mod definitely won't work. It's not working for you.
Would this work on N910U?
It works on the 910C running Nemesis
Good job OP, this mod on 910C it is been hit and miss with a lot of distortion. This is the best implementation I have used. ?
Finaly N910c has this mod
It is working. Thank you very much :highfive::highfive:
Came from @mangui's post in NEMESIS REFINED V3.8.5 N7 Port by*ananjaser1211
Confirmed!!! This work good on 910C , thanks very good mod
Working, but after first call - microphone stop working
Fixed call microphone
alextalexus said:
Working, but after first call - microphone stop working
Click to expand...
Click to collapse
I've fixed it ?
Hi theres a bug
when I plug in earphones , sound still comes out of front mic
Here is the source pushed to GitHub
https://github.com/salvenose/dual_mod
Possible Fix
Ryuce said:
Hi theres a bug
when I plug in earphones , sound still comes out of front mic
Click to expand...
Click to collapse
Can you tell me if this fix works
https://raw.githubusercontent.com/salvenose/dual_mod/master/default_gain.conf
sVenose said:
Can you tell me if this fix works
https://raw.githubusercontent.com/salvenose/dual_mod/master/default_gain.conf
Click to expand...
Click to collapse
Thanks bro its fixed!
Ryuce said:
Thanks bro its fixed!
Click to expand...
Click to collapse
Alright. Just added v3 to the original post. Have a nice day and God bless you.
Wooooow
Thats awesome
V3 Working great on N910C ,
I found another bug
When i make phone call people i call cant hear me
Ryuce said:
I found another bug
When i make phone call people i call cant hear me
Click to expand...
Click to collapse
Yes i have the same problem,
I have to restart my phone, then it worka fine
Hi again,
After update to erobotrom v1.2, I have the same problem - microphone stop working. Somebody have the original mixer_path and default_gain or the other solution for this problem. Thx.
Related
guys anyone tried call recording for our cm11 ? or mokee?? i tried many apps .. but no use.. someone posted automatic call recorder works .. i too tried ... the source of that file is changed automatically .. i tried xposed module cm recording .. that one works only our voice is recorded .. opponent voice is not clear..we need perfect recorder like LEWA OS inbuilt ..!! some one try to port that dialer to cm 11 . any ideas . develpers help needed .. thanks in advance.. guys discuss here about call recording
arunon2013 said:
guys anyone tried call recording for our cm11 ? or mokee?? i tried many apps .. but no use.. someone posted automatic call recorder works .. i too tried ... the source of that file is changed automatically .. i tried xposed module cm recording .. that one works only our voice is recorded .. opponent voice is not clear..we need perfect recorder like LEWA OS inbuilt ..!! some one try to port that dialer to cm 11 . any ideas . develpers help needed .. thanks in advance.. guys discuss here about call recording
Click to expand...
Click to collapse
try to use Xposed modules
search Enable cm call recording in download section
Have a nice day
Sent from my p715 using XDA Free mobile app
shamescool said:
try to use Xposed modules
search Enable cm call recording in download section
Have a nice day
Sent from my p715 using XDA Free mobile app
Click to expand...
Click to collapse
i tried dude .. no use .. only our own voice is clear .. opponent voice is low .. thats the prob
arunon2013 said:
i tried dude .. no use .. only our own voice is clear .. opponent voice is low .. thats the prob
Click to expand...
Click to collapse
so our only chance is using 3rd party voice recorders:banghead:
Sent from my p715 using XDA Free mobile app
yes..we need our developers help.. waiting for their reply
Sent from my LG P715 using XDA Premium 4 mobile app
Yes, I need this feature as well.
As far as I managed to understand, problem is the lack of ability for line recording, as opposed to microphone recording which is enabled. Obviously with microphone recording, the far side's volume is very week, so that's why you it doesn't work properly.
Digdis said:
Yes, I need this feature as well.
As far as I managed to understand, problem is the lack of ability for line recording, as opposed to microphone recording which is enabled. Obviously with microphone recording, the far side's volume is very week, so that's why you it doesn't work properly.
Click to expand...
Click to collapse
exactly same prob ..
Im not using CM 11 ATM ,but have you guys tried this app?
http://forum.xda-developers.com/android/apps-games/app-boldbeast-call-recorder-galaxy-htc-t2923904
i found it in the android general forum.
kalel29 said:
Im not using CM 11 ATM ,but have you guys tried this app?
http://forum.xda-developers.com/android/apps-games/app-boldbeast-call-recorder-galaxy-htc-t2923904
i found it in the android general forum.
Click to expand...
Click to collapse
Thanks. Still same problem. I asked for help in this thread, as this app seems very flexible and dev seems pretty responsive.
Digdis said:
Thanks. Still same problem. I asked for help in this thread, as this app seems very flexible and dev seems pretty responsive.
Click to expand...
Click to collapse
The problem with call recording is in kernel. Our kernel does not support 2 way recording (so both voices recording from line). It will record from headphones. No way to fix with any problem. Only way is to add 2-way call recording in kernel.
christi9503 said:
The problem with call recording is in kernel. Our kernel does not support 2 way recording (so both voices recording from line). It will record from headphones. No way to fix with any problem. Only way is to add 2-way call recording in kernel.
Click to expand...
Click to collapse
That's not entirely true. If you look at what I wrote in this app's thread to the dev, I managed to produce a scenario (involving the headphones) in which I managed to make it work.
Digdis said:
That's not entirely true. If you look at what I wrote in this app's thread to the dev, I managed to produce a scenario (involving the headphones) in which I managed to make it work.
Click to expand...
Click to collapse
Yeah, using headphones. With speaker it will not work without line recording imo.
christi9503 said:
Yeah, using headphones. With speaker it will not work without line recording imo.
Click to expand...
Click to collapse
Nope. Without headphones, recording when speaker is activated also works.
Digdis said:
Nope. Without headphones, recording when speaker is activated also works.
Click to expand...
Click to collapse
But it doesn't work when you use earpiece right?
christi9503 said:
But it doesn't work when you use earpiece right?
Click to expand...
Click to collapse
It does in one very awkward scenario. Copying here what I wrote in the Boldbeast call recorder thread. Here's the scenario:
- Plugged headphones
- Made the call and started recording (Let's call it stage 1). At this point I couldn't hear the call sound in my headphones, but still in the phone (no such problem if I don't record)
- Turned speaker on (stage 2). Now I hear the call in the speaker of course
- Turned speaker off, at this point I could hear the call in my headphones (stage 3)
Now when playing back the recording, I could see that in stage 1 I could hear the far side low, but in stages 2 & 3 I could hear it fine.
Note that stage 3 is the interesting one. The speaker is off, I hear the sound in my headphones, and the far end is recorded fine.
I really can't put a finger on the reason to the problem. I'm just saying I reached a state where I could record a 2-way call, without having the speaker on at this stage.
Digdis said:
It does in one very awkward scenario. Copying here what I wrote in the Boldbeast call recorder thread. Here's the scenario:
- Plugged headphones
- Made the call and started recording (Let's call it stage 1). At this point I couldn't hear the call sound in my headphones, but still in the phone (no such problem if I don't record)
- Turned speaker on (stage 2). Now I hear the call in the speaker of course
- Turned speaker off, at this point I could hear the call in my headphones (stage 3)
Now when playing back the recording, I could see that in stage 1 I could hear the far side low, but in stages 2 & 3 I could hear it fine.
Note that stage 3 is the interesting one. The speaker is off, I hear the sound in my headphones, and the far end is recorded fine.
I really can't put a finger on the reason to the problem. I'm just saying I reached a state where I could record a 2-way call, without having the speaker on at this stage.
Click to expand...
Click to collapse
i cant understand .. could u explain me via video .. thanks in advance
arunon2013 said:
i cant understand .. could u explain me via video .. thanks in advance
Click to expand...
Click to collapse
Had problems in the past uploading videos, so will guide you step by step. Please try to keep up.
First of all make sure your device is properly rooted and that you uninstall all other call recording apps.
Now install BoldBeast call recorder.
After installation, go to the application setup, Call settings :
- Set call recording mode to 22
- Enable root options (took me a few times until it worked, but it should work)
- Fix Recording Issues - mark all options except for Auto switch speaker on
(On a side note - these settings were the only ones that somehow worked. You are welcome to try other ones)
Now after setting this up, you will see a record icon for any call you make. Clicking it will start recording the call (showing a blue paw icon in the status bar). You can then hear the recorded calls by selecting the phone icon in the app.
Now to scenario I described:
- Plug your earphones in
- Make a call
- Click the record button. At this point, you won't hear the audio in your earphones but still in the phone
- Turn the speaker on, then turn it off
- You will now hear the audio in your earphones
Now after you hangup, you will hear both sides of the call starting the point you turned the speaker on and off.
This is really awkward. I guess christi is right by saying that the problem is in the kernel/ROM (as it worked properly with stock JB & KK). In addition, this app's dev told me it should have worked for me (using another mode - 34), and that he couldn't help if it didn't. So, I guess that until the kernel/ROM is fixed, we won't have call recording working normally in this ROM.
Digdis said:
Had problems in the past uploading videos, so will guide you step by step. Please try to keep up.
First of all make sure your device is properly rooted and that you uninstall all other call recording apps.
Now install BoldBeast call recorder.
After installation, go to the application setup, Call settings :
- Set call recording mode to 22
- Enable root options (took me a few times until it worked, but it should work)
- Fix Recording Issues - mark all options except for Auto switch speaker on
(On a side note - these settings were the only ones that somehow worked. You are welcome to try other ones)
Now after setting this up, you will see a record icon for any call you make. Clicking it will start recording the call (showing a blue paw icon in the status bar). You can then hear the recorded calls by selecting the phone icon in the app.
Now to scenario I described:
- Plug your earphones in
- Make a call
- Click the record button. At this point, you won't hear the audio in your earphones but still in the phone
- Turn the speaker on, then turn it off
- You will now hear the audio in your earphones
Now after you hangup, you will hear both sides of the call starting the point you turned the speaker on and off.
This is really awkward. I guess christi is right by saying that the problem is in the kernel/ROM (as it worked properly with stock JB & KK). In addition, this app's dev told me it should have worked for me (using another mode - 34), and that he couldn't help if it didn't. So, I guess that until the kernel/ROM is fixed, we won't have call recording working normally in this ROM.
Click to expand...
Click to collapse
thanks for ur explanation .. ( dis question is for christi .. he s promised me to make kernal with 2 way call recording ) wat about ur promise man ? can u remember it?
arunon2013 said:
thanks for ur explanation .. ( dis question is for christi .. he s promised me to make kernal with 2 way call recording ) wat about ur promise man ? can u remember it?
Click to expand...
Click to collapse
Firstly, I got my device back. Secondly, I have never ever promised anything like that. I said that I will watch on it and see what can be done, so never promised a thing. This is not a priority for me since it's not my job or anything like this. I am making this for free and I have never charged anything so far. Who wants can donate, but again, I am not charging, so I am making this when I want/ have free time/ have the mood for it. If you still doubt it, or anyone does, I have the pm saved. Please don't say I promised when I didn't do such thing. Things like this drive me nuts. Have a nice day.
cool man.. i just said simply.. dont be serious. sorry if i anything did wrongly..
Sent from my p715 using XDA Premium 4 mobile app
This is a fix for the audio skipping when playback starts (audiophiles must have noticed it, while others dont bother ) and audio howling/distortion on full volume.
The audio_hw module is taken from omni, so thanks @rooque for that. And the MTP (acdbs) are mi note's files taken from ivans repo .
Tested working on rr and aicp.
Flash using CWM/TWRP.
Please test and confirm.
Thank You.
Edit: Updated the zip file since it was causing puchier sound in earpiece.
I guess it is to fix audio cracking when in full volume for speaker
24likan said:
I guess it is to fix audio cracking when in full volume for speaker
Click to expand...
Click to collapse
Yes and it also fixes audio skipping in the begining.
vasishath said:
Yes and it also fixes audio skipping in the begining.
Click to expand...
Click to collapse
Thanks bro
vasishath said:
This is a fix for the audio skipping when playback starts (audiophiles must have noticed it, while others dont bother ) and audio howling/distortion on full volume.
The audio_hw module is taken from omni, so thanks @rooque for that. And the MTP (acdbs) are mi note's files taken from ivans repo .
Tested working on rr and aicp.
Flash using CWM/TWRP.
Please test and confirm.
Thank You.
Edit: Updated the zip file since it was causing puchier sound in earpiece.
Click to expand...
Click to collapse
after flashing the zip,the sound quality has improved drastically but i am facing a bug now..Whenever i call someone with loudspeaker on,the other person cant hear anything...infact i am able to hear my voice from the mic as if my voice is getting reflected back...please fix this issue...thanks
Not works on los 14.1,it give no sounds,both speaker and headset
Hi All. The sound is fixed as you know but not on all ROM. So i've made a Fix zip. Tried on US and G version.
Edit: working on A2017 (Chinese version)
IMPORTANT: I'm not responsible for anything which could be happen. I suggest to make a backup from TWRP.
First of all i didn't fix it. Thanks @Unjustified Dev , @DrakenFX and Anynomous Dev
Instruction:
Flash zip via TWRP.
Download:
v4.1
https://www.androidfilehost.com/?fid=457095661767153882
v4
https://www.androidfilehost.com/?fid=457095661767152958
v2
https://www.androidfilehost.com/?fid=529152257862718359
WesTD said:
Hi All. The sound is fixed as you know but not on all ROM. So i've made a Fix zip. Tried on US and G versions.
IMPORTANT: I'm not responsible for anything which could be happen. I suggest to make a backup from TWRP.
First of all i didn't fix it. Thanks @Unjustified Dev , @DrakenFX and Anynomous Dev
Instruction:
Flash zip via TWRP.
Download:
uploading.
Click to expand...
Click to collapse
Thanks for that.
Do correct me if I'm wrong, but this still does not make use of the AKM DAC, right? This still uses the Qualcomm inbuilt DAC?
Thanks in any case!
joaste said:
Thanks for that.
Do correct me if I'm wrong, but this still does not make use of the AKM DAC, right? This still uses the Qualcomm inbuilt DAC?
Thanks in any case!
Click to expand...
Click to collapse
It's wired for it's AKM DAC the issue was we were dependent on ZTE crappy patch that made us bypass and force audio on. Now the amplifier HAL correctly calls to the NXP driver to properly calibrate and initialize audio in all usecases. It's more so the developer is trying to recreate how stock handles stuff like voice speaker, speaker reversing, mono + stereo, etc.
Unjustified Dev said:
It's wired for it's AKM DAC the issue was we were dependent on ZTE crappy patch that made us bypass and force audio on. Now the amplifier HAL correctly calls to the NXP driver to properly calibrate and initialize audio in all usecases. It's more so the developer is trying to recreate how stock handles stuff like voice speaker, speaker reversing, mono + stereo, etc.
Click to expand...
Click to collapse
How was this fix done exactly? Was it just fiddling with some configuration files or did you have to completely rewrite the way android works the audio so it calls the driver correctly? And if so, is it the same way Dolby does? I'm so curious how you guys and the anonymous dev managed to fix it
Also, I can't wait for this to upload. This + LOS based roms and this phone would be absolutely perfect. Too bad it's not mainstream enough to get more attention
If we flash this, will it cause any issues once it's officially merged into LOS and we update LOS on the phone?
WesTD said:
Hi All. The sound is fixed as you know but not on all ROM. So i've made a Fix zip. Tried on US and G versions.
IMPORTANT: I'm not responsible for anything which could be happen. I suggest to make a backup from TWRP.
First of all i didn't fix it. Thanks @Unjustified Dev , @DrakenFX and Anynomous Dev
Instruction:
Flash zip via TWRP.
Download:
uploading.
Click to expand...
Click to collapse
The download is not available.
Teet1 said:
How was this fix done exactly? Was it just fiddling with some configuration files or did you have to completely rewrite the way android works the audio so it calls the driver correctly? And if so, is it the same way Dolby does? I'm so curious how you guys and the anonymous dev managed to fix it
Also, I can't wait for this to upload. This + LOS based roms and this phone would be absolutely perfect. Too bad it's not mainstream enough to get more attention
Click to expand...
Click to collapse
Has nothing to do with dolby. There's a file libtfa9890.so stock audio hal calls this file does it's magic. On lineage we don't have the amp source which is packed into the audio hal on stock. We use an amplifier hal all this hal does it try to produce whatever the heck the stock audio hal did when it loaded libtfa9890.so. It basically allows you to instrument custom calls without touching the audio hal of the ROM therefore keeping it clean. ZTE gave us a patch that force loaded libtfa9890 and immediately said ignore all cases turn on the speaker. What the dev did is rewrite the patch to properly call all functions such as calibrate, set mode , speaker on , speaker off ,etc. This way we don't just force speaker we actually start saying if in call handle the speakers this way. If music is playing handle them this way. We don't just say if need sound ramp up the amp and make sound.
link added.
Has anyone who flashed it have a decrease in system performance?
Sent from my ZTE A2017U using Tapatalk
WesTD said:
link added.
Click to expand...
Click to collapse
Just installed this fix.
It works, it works, Hallelujah!.
Ya so this zip works on the Chinese version, so you can update the op
Also passed the stereo test. Left and right channels are both working independently and awesomely.
The distortion has nearly disappeared.
Calls work.
Thanks to all the devs especially unjustified dev and anonymous dev.
Thanks also to drakenfx and westd.
Also now that patch 3 is out, can we expect another zip in the future!
Unjustified Dev said:
Has nothing to do with dolby. There's a file libtfa9890.so stock audio hal calls this file does it's magic. On lineage we don't have the amp source which is packed into the audio hal on stock. We use an amplifier hal all this hal does it try to produce whatever the heck the stock audio hal did when it loaded libtfa9890.so. It basically allows you to instrument custom calls without touching the audio hal of the ROM therefore keeping it clean. ZTE gave us a patch that force loaded libtfa9890 and immediately said ignore all cases turn on the speaker. What the dev did is rewrite the patch to properly call all functions such as calibrate, set mode , speaker on , speaker off ,etc. This way we don't just force speaker we actually start saying if in call handle the speakers this way. If music is playing handle them this way. We don't just say if need sound ramp up the amp and make sound.
Click to expand...
Click to collapse
Genius. Didn't mean to say Dolby, meant zte I had Dolby Atmos on the mind. But if it's nothing to do with Dolby, how come they didn't release the source for a direct fix instead of releasing a half assed patch for devs to work with? Then there wasn't be an issue of it being closed or open source
WesTD said:
link added.
Click to expand...
Click to collapse
My latest Gerrit patch?
Sent from my ZTE A2017U using Tapatalk
FIGURES!!! I just went back to stock (but still have unlocked bootloader)....
Looks like I know what I'll be doing, at some point, this week!
GREAT WORK @DrakenFX
Unjustified Dev said:
My latest Gerrit patch?
Sent from my ZTE A2017U using Tapatalk
Click to expand...
Click to collapse
not latest, 2nd one. @DrakenFX will upload it soon.
WesTD said:
not latest, 2nd one. @DrakenFX will upload it soon.
Click to expand...
Click to collapse
Yeah, I sent him the libraries a few hours ago. Let me know if you need anything else.
Sent from my ZTE A2017U using Tapatalk
Unjustified Dev said:
Yeah, I sent him the libraries a few hours ago. Let me know if you need anything else.
Sent from my ZTE A2017U using Tapatalk
Click to expand...
Click to collapse
Okay man. thanks for your works.
TWRP Flashable Stereo Sound Patch 3.
https://www.androidfilehost.com/?fid=457095661767152906
Thanks to Anonymous Dev. & @Unjustified Dev for all of this.
DrakenFX said:
TWRP Flashable Stereo Sound Patch 3.
https://www.androidfilehost.com/?fid=457095661767152906
Thanks to Anonymous Dev. & @Unjustified Dev for all of this.
Click to expand...
Click to collapse
Can users that already have the audio fix install this (NucleaROM)??
aLexzkter said:
Can users that already have the audio fix install this (NucleaROM)??
Click to expand...
Click to collapse
Yep this would work on any rom that uses amplifier hal which is all of them
Sent from my ZTE A2017U using Tapatalk
What's the improvement of V3 over V2 ?
PS : THX to every1 involved who made this possible !
Install "Ainur JamesDSP v1.7" Magisk module and choose the HQ 64bit driver
Install "Audio Modification Library v.1.8.1" Magisk module
Reboot
Configure JamesDSP app
Confirmed working (speakers & headphones (can't test bluetooth)) on my FIG-LX1 (L31) - EMUI 8.0.0.148(C432) - Magisk v17.1
Edit: If you don't want ringtones/notification-sounds to be processed, switch DSP registration from global to conventional. (3dot menu - top right, screenshot added)
Huge thanks to natanrosenfeld (he made a YT video, explaining a fix for previous version (now fixed with v1.7)) - and especially the JamesDSP dev team!
Great news I seen it on .android-hilfe.de myself
Messing around and cant seem to get it right, either too loud or doesnt work
Viper4android was much easier to setup, using Huawei DTS.irs or srs_2_1.irs then not much else and worked great
redultra82 said:
Great news I seen it on .android-hilfe.de myself
Messing around and cant seem to get it right, either too loud or doesnt work
Viper4android was much easier to setup, using Huawei DTS.irs or srs_2_1.irs then not much else and worked great
Click to expand...
Click to collapse
Have you tried using the same impulse response files with JamesDSP?
Copy the .irs (or .wav, .flac) to /storage/emulated/0/JamesDSP/Convolver and enable Convolver in JamesDSP.
Works great here.
Greetings from "androphil"
callmeWhiskers said:
Have you tried using the same impulse response files with JamesDSP?
Copy the .irs (or .wav, .flac) to /storage/emulated/0/JamesDSP/Convolver and enable Convolver in JamesDSP.
Works great here.
Greetings from "androphil"
Click to expand...
Click to collapse
I did thanks
Can you send screenshot of what you have, not sure on other settings
redultra82 said:
(...)Can you send screenshot of what you have, not sure on other settings
Click to expand...
Click to collapse
Even if we'd share the exact same setup (e.g. settings/IR xy sound great with my Shure SE425 in-ear headphones, but not so great with my AKG Q701) and preference of music, it would still be incredibly subjective and mainly based on taste. Certified sound-engineers would probably disagree, I guess
My suggestion is: leave every (other) option off, download a pack of different IRs (e.g. https://forum.xda-developers.com/zenfone2/general/collection-convolver-samples-389-t3140299) and try each one out. If you found one you like, (slightly) tune it with the EQ. At least that's my "non-pro" approach.
Mostly all I want is to make the phone louder, well the phone speaker, on Bluetooth speakers etc it's fairly OK
Next issue is echo sound on ringtone and notification
I'll try IRS out and maybe someday have Viper4android
It's a system-wide audio-mod, so yes, if you have e.g. Virtual Room Effect turned on or use a noticably "reverberating" impulse response file, you'll experience echo on ringtones/notification-sounds too.
I've managed to make the speakers slightly louder by choosing the highest IR Volume Level (30dB), but I think the device's speaker volume level/overall sound-quality is just physically limited. They are not the "best" speakers after all.
callmeWhiskers said:
It's a system-wide audio-mod, so yes, if you have e.g. Virtual Room Effect turned on or use a noticably "reverberating" impulse response file, you'll experience echo on ringtones/notification-sounds too.
I've managed to make the speakers slightly louder by choosing the highest IR Volume Level (30dB), but I think the device's speaker volume level/overall sound-quality is just physically limited. They are not the "best" speakers after all.
Click to expand...
Click to collapse
I noticed the room effect and turned it off, but just using Irs or some of them and seemed to be an echo,
Speaker is good enough, it is only a phone after all, there are small bluetooth speakers now that have great volume to help
A nice guy from the Telegram channel pointed out, that you can avoid processing system sounds (ringtones/notification) by switching DSP registration mode from global to conventional (screenshot added to OP).
YEEEES!!!! This mod is also working on Huawei P20Pro with EMUI8.1.. I just follow the same steps above. Thanks a lot man!
callmeWhiskers said:
Install "Ainur JamesDSP v1.7" Magisk module and choose the HQ 64bit driver
Install "Audio Modification Library v.1.8.1" Magisk module
Reboot
Configure JamesDSP app
Confirmed working (speakers & headphones (can't test bluetooth)) on my FIG-LX1 (L31) - EMUI 8.0.0.148(C432) - Magisk v17.1
Edit: If you don't want ringtones/notification-sounds to be processed, switch DSP registration from global to conventional. (3dot menu - top right, screenshot added)
Huge thanks to natanrosenfeld (he made a YT video, explaining a fix for previous version (now fixed with v1.7)) - and especially the JamesDSP dev team!
Click to expand...
Click to collapse
Hi do you know if I can change mixer path values without root and using adb on pc? , I'm trying to raise volume of WhatsApp calls, calls and maybe a bit of loud speaker volume but I'm trying to avoid root etc. Thanks any advice would be appreciated or a link to tutorials. I'm on psmart. Thanks again
jason13v8 said:
Hi do you know if I can change mixer path values without root and using adb on pc? , I'm trying to raise volume of WhatsApp calls, calls and maybe a bit of loud speaker volume but I'm trying to avoid root etc. Thanks any advice would be appreciated or a link to tutorials. I'm on psmart. Thanks again
Click to expand...
Click to collapse
Sorry - I'm not an expert, so don't take my word for it - but I don't think that's possible, since all these files are stored in locations, where (non root) users don't have write permissions. Even with a rooted and/or custom recovery device, I don't think it's possible to alter app-specific volumes by just changing mixer_paths.xml values.
callmeWhiskers said:
Sorry - I'm not an expert, so don't take my word for it - but I don't think that's possible, since all these files are stored in locations, where (non root) users don't have write permissions. Even with a rooted and/or custom recovery device, I don't think it's possible to alter app-specific volumes by just changing mixer_paths.xml values.
Click to expand...
Click to collapse
Sorry I know I mentioned whats app but really I just mean overall volume. With my moto g5 I was able to edit mixer path values which led to louder everything. But that was only with root as I'm new to adb. Thanks for your response
jason13v8 said:
Sorry I know I mentioned whats app but really I just mean overall volume. With my moto g5 I was able to edit mixer path values which led to louder everything. But that was only with root as I'm new to adb. Thanks for your response
Click to expand...
Click to collapse
In case your bootloader is unlocked, iirc you could theoretically fastboot flash TWRP - and use TWRP's "privileged" terminal (e.g. (mount /system), adb pull/push and edit the file(s)), and then (re)flash stock recovery again - without actually rooting the device.
Again, I'm not an expert (also didn't try it myself) and can't guarantee above mentioned procedure works, despite my inner-Sherlock-Holmes tells me, your bootloader is actually not unlocked.
callmeWhiskers said:
In case your bootloader is unlocked, iirc you could theoretically fastboot flash TWRP - and use TWRP's "privileged" terminal (e.g. (mount /system), adb pull/push and edit the file(s)), and then (re)flash stock recovery again - without actually rooting the device.
Again, I'm not an expert (also didn't try it myself) and can't guarantee above mentioned procedure works, despite my inner-Sherlock-Holmes tells me, your bootloader is actually not unlocked.
Click to expand...
Click to collapse
Yeah still locked dude, tried DC unlocker but they refunded as I'm on latest security patch and admitted there is nothing they can do right now.
Themes
With MIUI 12 xiaomi introduce many new features and it's new version of game turbo with dream feature voice changer . But problem is that it is only working without earphone , when you plugged in it stop working .
What we all know is that voice changer only working with loudspeaker , right..? .. but it's half truths actually it's working with device microphone ...
My conclusion :
Voice changer is not having bug , may be its due to some limitations or compatibility ..
So what if you use your earphone for sounds output and device microphone for input...
Yes this is possible just follow below steps...
1) go to play store
2) search for lesser Audioswitch ( https://play.google.com/store/apps/details?id=com.nordskog.LesserAudioSwitch)
3) open app
4) go to settings (upper right corner below your battery icon)
5) enable switch microphone
6) back to app main screen
7) click on headphones
8) press the microphone icon next to the headphones
9) select internal microphone ...
10) now start your poobg and enjoy voice changer with head/earphone
11) to reset changes re-start your device...
For low microphone voice issue.. (mostly with AOSP Rom)
While we know that it's bugged because it can't route to the headset mic while connected to headset...
Switch between internal microphone and headphones
May be it will resolve....
Just a hope... Try and confirm us ..
Tested with Mortal os (MemeUi)+K20 PRO ....
No working??? Try this ...
Clear data of lesser Audioswitch app , now from start page select mute (the very first page of app after installing) and follow from 4-9 ...
IF not work reboot Your device and foloow 6-9
Thanks A Lot Technobuzznet to make a video for the same ...
:highfive:
And thanks Raaj52 for awesome MortalOs (MemeUi) the only reason to using MiUi .
not working... Works only on Demo Mode
Vatumb said:
not working... Works only on Demo Mode
Click to expand...
Click to collapse
Working here... Follow the complete process
QadirAliKhan said:
Working here... Follow the complete process
Click to expand...
Click to collapse
Followed the same 5 to 6 times... not working for me (K20 Pro Masik 16.1)
Vatumb said:
Followed the same 5 to 6 times... not working for me (K20 Pro Masik 16.1)
Click to expand...
Click to collapse
Unplugged earphone ..
Reboot device..
Plugged earphone..
Open lease app..
Click on headphones..
Click the microphone icon just next to the headphones button ..
Select internal earphone....
Working with pubg , whatsapp and every app I am using this..
QadirAliKhan said:
Unplugged earphone ..
Reboot device..
Plugged earphone..
Open lease app..
Click on headphones..
Click the microphone icon just next to the headphones button ..
Select internal earphone....
Working with pubg , whatsapp and every app I am using this..
Click to expand...
Click to collapse
If still not working clear data of lesser app..
Open again...
Select mute from first page ....
QadirAliKhan said:
If still not working clear data of lesser app..
Open again...
Select mute from first page ....
Click to expand...
Click to collapse
Works on Normal too.... already made a video and posted on Technobuzznet channel
BTW Thanks
From RajeshRajput
Well it looks like the app could also fix the low headset mic issue by making the input on to the headset mic. But I didn't test it yet
wisnuyogan said:
Well it looks like the app could also fix the low headset mic issue by making the input on to the headset mic. But I didn't test it yet
Click to expand...
Click to collapse
May be many people saying same thing...
While we know that it's bugged because it can't route to the headset mic while connected to headset...
Can you try and confirm back ...
QadirAliKhan said:
May be many people saying same thing...
While we know that it's bugged because it can't route to the headset mic while connected to headset...
Can you try and confirm back ...
Click to expand...
Click to collapse
Sorry I can't. I'm also on miui, it happens on aosp
Vatumb said:
Works on Normal too.... already made a video and posted on Technobuzznet channel
BTW Thanks
From RajeshRajput
Click to expand...
Click to collapse
You are Rajesh from technobuzznet YouTube???
btw ... Thanks a lot to mention me in the video...
App Description says:
Android 11 support:
Due to changes to made Android, this app cannot function on Android 11 and later.
There is now a native output-selection option found in the volume panel, which provides some of the functionality previously offered by this app.
Click to expand...
Click to collapse
Hello im using RN8P and the voice changer cannot be found my device is not rooted though