Related
I have a Nexus one, and followed the instructions here:
http://forum.xda-developers.com/showthread.php?t=631389
However, most of the page is devoted to getting the system up and running in a debian environment.
I substituted a stage3 gentoo build found here:
http://mirrors.kernel.org/gentoo/releases/arm/autobuilds/current-stage3/armv7a-unknown-linux-gnueabi/
And to my surprise, I was able to chroot into the partiton, and get it running. Besides a bunch of small annoying things, it is working. I was (and am) able to compile new packages, including the kernel.
The only issue I'm seeing is when I go to boot up off the kernel.
I started with his stock 2.6.33 kernel config, and did a "make oldconfig", resulting in the config file seen in the next post.
After having to wrangle with the kernel errors (some of the headers were just f*cking gone), I got it to compile, but when I go to boot off of it (with fastboot), the system just hangs. There are no log files, so I know the kernel didn't load right.
We need to use some very experimental parts of the kernel, as well as usertools (mesh networking over wifi), and need to use stock tools. Has anyone gotten a stock kernel to compile for the nexus one? Are there any debug tools available to check status in the event of a kernel panic? The framebuffer isn't available for the video card, so I have no way of visually checking on the progress of the kernel to see where it panics'.
Can anyone help me out?
Thanks
I don't remember his name, but there is a gentoo dev that posts in these threads. Good work so far. If I run across his post I'll let you know.
Kernel Config...
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.29
# Mon Feb 8 20:59:13 2010
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION="-droid-debian"
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
#
# RCU Subsystem
#
CONFIG_CLASSIC_RCU=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_GROUP_SCHED=y
CONFIG_FAIR_GROUP_SCHED=y
CONFIG_RT_GROUP_SCHED=y
CONFIG_CGROUP_SCHED=y
CONFIG_CGROUPS=y
CONFIG_CGROUP_DEBUG=y
CONFIG_CGROUP_FREEZER=y
CONFIG_CGROUP_CPUACCT=y
CONFIG_RESOURCE_COUNTERS=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_PANIC_TIMEOUT=5
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_KALLSYMS=y
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_ASHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_BLOCK=y
CONFIG_LBD=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_DEFAULT_AS=y
CONFIG_DEFAULT_IOSCHED="anticipatory"
CONFIG_FREEZER=y
#
# System Type
#
CONFIG_ARCH_MSM=y
CONFIG_ARCH_QSD8X50=y
CONFIG_ARCH_MSM_SCORPION=y
CONFIG_MSM_MDP31=y
CONFIG_MSM_AMSS_VERSION=6225
CONFIG_MSM_AMSS_VERSION_6225=y
CONFIG_MSM_DEBUG_UART=1
CONFIG_MSM_DEBUG_UART1=y
#
# MSM Board Type
#
CONFIG_MACH_SWORDFISH=y
CONFIG_MACH_MAHIMAHI=y
CONFIG_HTC_35MM_JACK=y
CONFIG_HTC_PWRSPLY=y
CONFIG_CACHE_FLUSH_RANGE_LIMIT=0x40000
CONFIG_MSM7X00A_USE_GP_TIMER=y
CONFIG_MSM7X00A_SLEEP_MODE_POWER_COLLAPSE_SUSPEND=y
CONFIG_MSM7X00A_SLEEP_MODE=0
CONFIG_MSM7X00A_IDLE_SLEEP_MODE_POWER_COLLAPSE=y
CONFIG_MSM7X00A_IDLE_SLEEP_MODE=1
CONFIG_MSM7X00A_IDLE_SLEEP_MIN_TIME=50000000
CONFIG_MSM7X00A_IDLE_SPIN_TIME=80000
CONFIG_MSM_IDLE_STATS=y
CONFIG_MSM_IDLE_STATS_FIRST_BUCKET=62500
CONFIG_MSM_IDLE_STATS_BUCKET_SHIFT=2
CONFIG_MSM_IDLE_STATS_BUCKET_COUNT=10
CONFIG_MSM_SMD=y
CONFIG_MSM_ONCRPCROUTER=y
CONFIG_MSM_RPCSERVERS=y
CONFIG_MSM_HW3D=y
CONFIG_MSM_QDSP6=y
CONFIG_WIFI_CONTROL_FUNC=y
#
# Processor Type
#
CONFIG_CPU_32=y
CONFIG_CPU_32v6K=y
CONFIG_CPU_V7=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
CONFIG_CPU_PABRT_IFAR=y
CONFIG_CPU_CACHE_V7=y
CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
CONFIG_CPU_TLB_V7=y
CONFIG_VERIFY_PERMISSION_FAULT=y
CONFIG_CPU_HAS_ASID=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y
#
# Processor Features
#
CONFIG_ARM_THUMB=y
CONFIG_ARM_THUMBEE=y
CONFIG_HAS_TLS_REG=y
CONFIG_ARM_L1_CACHE_SHIFT=5
#
# Bus support
#
#
# Kernel Features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_VMSPLIT_3G=y
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
CONFIG_ARCH_FLATMEM_HAS_HOLES=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
CONFIG_UNEVICTABLE_LRU=y
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ALIGNMENT_TRAP=y
#
# Boot options
#
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="mem=64M console=ttyMSM,115200n8"
#
# CPU Power Management
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_STAT=y
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_MIN_TICKS=2
CONFIG_CPU_FREQ_SAMPLING_LATENCY_MULTIPLIER=500
#
# Floating point emulation
#
#
# At least one emulation must be selected
#
CONFIG_VFP=y
CONFIG_VFPv3=y
CONFIG_NEON=y
#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
CONFIG_HAVE_AOUT=y
#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_HAS_WAKELOCK=y
CONFIG_HAS_EARLYSUSPEND=y
CONFIG_WAKELOCK=y
CONFIG_WAKELOCK_STAT=y
CONFIG_USER_WAKELOCK=y
CONFIG_EARLYSUSPEND=y
CONFIG_FB_EARLYSUSPEND=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_NET=y
#
# Networking options
#
CONFIG_COMPAT_NET_DEV_OPS=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
CONFIG_XFRM_IPCOMP=y
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_INET_AH=y
CONFIG_INET_ESP=y
CONFIG_INET_IPCOMP=y
CONFIG_INET_XFRM_TUNNEL=y
CONFIG_INET_TUNNEL=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_LRO=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
CONFIG_ANDROID_PARANOID_NETWORK=y
CONFIG_NETFILTER=y
CONFIG_NETFILTER_ADVANCED=y
CONFIG_BRIDGE_NETFILTER=y
#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=y
CONFIG_NETFILTER_NETLINK_QUEUE=y
CONFIG_NETFILTER_NETLINK_LOG=y
CONFIG_NF_CONNTRACK=y
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NETFILTER_XTABLES=y
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=y
CONFIG_NETFILTER_XT_TARGET_CONNMARK=y
CONFIG_NETFILTER_XT_TARGET_MARK=y
CONFIG_NETFILTER_XT_TARGET_NFLOG=y
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=y
CONFIG_NETFILTER_XT_TARGET_RATEEST=y
# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
CONFIG_NETFILTER_XT_TARGET_TCPMSS=y
# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
CONFIG_NETFILTER_XT_MATCH_COMMENT=y
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=y
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=y
CONFIG_NETFILTER_XT_MATCH_CONNMARK=y
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=y
CONFIG_NETFILTER_XT_MATCH_DCCP=y
CONFIG_NETFILTER_XT_MATCH_DSCP=y
CONFIG_NETFILTER_XT_MATCH_ESP=y
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=y
CONFIG_NETFILTER_XT_MATCH_HELPER=y
CONFIG_NETFILTER_XT_MATCH_IPRANGE=y
CONFIG_NETFILTER_XT_MATCH_LENGTH=y
CONFIG_NETFILTER_XT_MATCH_LIMIT=y
CONFIG_NETFILTER_XT_MATCH_MAC=y
CONFIG_NETFILTER_XT_MATCH_MARK=y
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=y
CONFIG_NETFILTER_XT_MATCH_OWNER=y
CONFIG_NETFILTER_XT_MATCH_POLICY=y
# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=y
CONFIG_NETFILTER_XT_MATCH_QUOTA=y
CONFIG_NETFILTER_XT_MATCH_RATEEST=y
CONFIG_NETFILTER_XT_MATCH_REALM=y
CONFIG_NETFILTER_XT_MATCH_RECENT=y
# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set
CONFIG_NETFILTER_XT_MATCH_SCTP=y
CONFIG_NETFILTER_XT_MATCH_STATE=y
CONFIG_NETFILTER_XT_MATCH_STATISTIC=y
CONFIG_NETFILTER_XT_MATCH_STRING=y
CONFIG_NETFILTER_XT_MATCH_TCPMSS=y
CONFIG_NETFILTER_XT_MATCH_TIME=y
CONFIG_NETFILTER_XT_MATCH_U32=y
# CONFIG_IP_VS is not set
#
# IP: Netfilter Configuration
#
CONFIG_NF_DEFRAG_IPV4=y
CONFIG_NF_CONNTRACK_IPV4=y
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
# CONFIG_IP_NF_QUEUE is not set
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_MATCH_ADDRTYPE=y
CONFIG_IP_NF_MATCH_AH=y
CONFIG_IP_NF_MATCH_ECN=y
CONFIG_IP_NF_MATCH_TTL=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_ULOG=y
CONFIG_NF_NAT=y
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=y
CONFIG_IP_NF_TARGET_NETMAP=y
CONFIG_IP_NF_TARGET_REDIRECT=y
CONFIG_NF_NAT_SNMP_BASIC=y
# CONFIG_NF_NAT_FTP is not set
# CONFIG_NF_NAT_IRC is not set
# CONFIG_NF_NAT_TFTP is not set
# CONFIG_NF_NAT_AMANDA is not set
# CONFIG_NF_NAT_PPTP is not set
# CONFIG_NF_NAT_H323 is not set
# CONFIG_NF_NAT_SIP is not set
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_CLUSTERIP=y
CONFIG_IP_NF_TARGET_ECN=y
CONFIG_IP_NF_TARGET_TTL=y
CONFIG_IP_NF_RAW=y
CONFIG_IP_NF_ARPTABLES=y
CONFIG_IP_NF_ARPFILTER=y
CONFIG_IP_NF_ARP_MANGLE=y
# CONFIG_BRIDGE_NF_EBTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_STP=y
CONFIG_BRIDGE=y
# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
CONFIG_LLC=y
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
CONFIG_NET_CLS_ROUTE=y
# CONFIG_DCB is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
CONFIG_BT=y
CONFIG_BT_L2CAP=y
CONFIG_BT_SCO=y
CONFIG_BT_RFCOMM=y
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=y
# CONFIG_BT_BNEP_MC_FILTER is not set
# CONFIG_BT_BNEP_PROTO_FILTER is not set
CONFIG_BT_HIDP=y
#
# Bluetooth device drivers
#
# CONFIG_BT_HCIBTSDIO is not set
CONFIG_BT_HCIUART=y
CONFIG_BT_HCIUART_H4=y
# CONFIG_BT_HCIUART_BCSP is not set
CONFIG_BT_HCIUART_LL=y
CONFIG_BT_HCIVHCI=y
# CONFIG_AF_RXRPC is not set
# CONFIG_PHONET is not set
CONFIG_FIB_RULES=y
CONFIG_WIRELESS=y
CONFIG_CFG80211=y
# CONFIG_CFG80211_REG_DEBUG is not set
CONFIG_NL80211=y
CONFIG_WIRELESS_OLD_REGULATORY=y
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
CONFIG_LIB80211=y
# CONFIG_LIB80211_DEBUG is not set
CONFIG_MAC80211=y
#
# Rate control algorithm selection
#
# CONFIG_MAC80211_RC_PID is not set
CONFIG_MAC80211_RC_MINSTREL=y
# CONFIG_MAC80211_RC_DEFAULT_PID is not set
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
CONFIG_MAC80211_RC_DEFAULT="minstrel"
CONFIG_MAC80211_MESH=y
CONFIG_MAC80211_LEDS=y
# CONFIG_MAC80211_DEBUGFS is not set
# CONFIG_MAC80211_DEBUG_MENU is not set
# CONFIG_WIMAX is not set
CONFIG_RFKILL=y
# CONFIG_RFKILL_PM is not set
# CONFIG_RFKILL_INPUT is not set
CONFIG_RFKILL_LEDS=y
# CONFIG_NET_9P is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH=""
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
#
# CONFIG_MTD_CFI is not set
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PLATRAM is not set
#
# Self-contained MTD device drivers
#
CONFIG_MTD_MSM_NAND=y
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
# CONFIG_MTD_NAND is not set
# CONFIG_MTD_ONENAND is not set
#
# LPDDR flash memory drivers
#
# CONFIG_MTD_LPDDR is not set
#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
CONFIG_MISC_DEVICES=y
CONFIG_ANDROID_PMEM=y
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_KERNEL_DEBUGGER_CORE is not set
CONFIG_UID_STAT=y
# CONFIG_WL127X_RFKILL is not set
CONFIG_APANIC=y
CONFIG_APANIC_PLABEL="crashdata"
# CONFIG_C2PORT is not set
#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_93CX6 is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# SCSI device support
#
CONFIG_MD=y
CONFIG_BLK_DEV_DM=y
CONFIG_DM_DEBUG=y
CONFIG_DM_CRYPT=y
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
CONFIG_TUN=y
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_SMC91X=y
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
CONFIG_BCM4329=m
CONFIG_BCM4329_FW_PATH="/etc/firmware/fw_bcm4329.bin"
CONFIG_BCM4329_NVRAM_PATH="/proc/calibration"
#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#
CONFIG_PPP=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPP_BSDCOMP=y
CONFIG_PPP_MPPE=y
CONFIG_PPPOLAC=y
CONFIG_PPPOPNS=y
CONFIG_SLHC=y
CONFIG_MSM_RMNET=y
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_EVDEV=y
CONFIG_INPUT_KEYRESET=y
#
# Input Device Drivers
#
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_MSM=y
CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI=y
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_TOUCHSCREEN_TSC2007 is not set
CONFIG_INPUT_MISC=y
# CONFIG_INPUT_ATI_REMOTE is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_CM109 is not set
CONFIG_INPUT_UINPUT=y
CONFIG_INPUT_GPIO=y
CONFIG_INPUT_KEYCHORD=y
CONFIG_INPUT_CAPELLA_CM3602=y
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_DEVMEM=y
# CONFIG_DEVKMEM is not set
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_MSM=y
CONFIG_SERIAL_MSM_CONSOLE=y
# CONFIG_SERIAL_MSM_CLOCK_CONTROL is not set
CONFIG_SERIAL_MSM_HS=y
CONFIG_SERIAL_BCM_BT_LPM=y
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
# CONFIG_DCC_TTY is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
#
# I2C Hardware Bus support
#
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_GPIO is not set
CONFIG_I2C_MSM=y
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SIMTEC is not set
#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_STUB is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_AKM8976 is not set
CONFIG_SENSORS_AKM8973=y
# CONFIG_SENSORS_PCA963X is not set
# CONFIG_SENSORS_MT9T013 is not set
CONFIG_VP_A1026=y
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
CONFIG_W1=y
#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_DS2482=y
# CONFIG_W1_MASTER_GPIO is not set
#
# 1-wire Slaves
#
# CONFIG_W1_SLAVE_THERM is not set
# CONFIG_W1_SLAVE_SMEM is not set
# CONFIG_W1_SLAVE_DS2431 is not set
# CONFIG_W1_SLAVE_DS2433 is not set
# CONFIG_W1_SLAVE_DS2760 is not set
CONFIG_W1_SLAVE_DS2784=y
# CONFIG_W1_SLAVE_BQ27000 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
CONFIG_BATTERY_DS2784=y
# CONFIG_BATTERY_BQ27x00 is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
#
# Multimedia devices
#
#
# Multimedia core support
#
CONFIG_VIDEO_DEV=y
CONFIG_VIDEO_V4L2_COMMON=y
# CONFIG_VIDEO_ALLOW_V4L1 is not set
CONFIG_VIDEO_V4L1_COMPAT=y
# CONFIG_DVB_CORE is not set
CONFIG_VIDEO_MEDIA=y
#
# Multimedia drivers
#
# CONFIG_MEDIA_ATTACH is not set
CONFIG_MEDIA_TUNER=y
CONFIG_MEDIA_TUNER_CUSTOMIZE=y
# CONFIG_MEDIA_TUNER_SIMPLE is not set
# CONFIG_MEDIA_TUNER_TDA8290 is not set
# CONFIG_MEDIA_TUNER_TDA827X is not set
# CONFIG_MEDIA_TUNER_TDA18271 is not set
# CONFIG_MEDIA_TUNER_TDA9887 is not set
# CONFIG_MEDIA_TUNER_TEA5761 is not set
# CONFIG_MEDIA_TUNER_TEA5767 is not set
# CONFIG_MEDIA_TUNER_MT20XX is not set
# CONFIG_MEDIA_TUNER_MT2060 is not set
# CONFIG_MEDIA_TUNER_MT2266 is not set
# CONFIG_MEDIA_TUNER_MT2131 is not set
# CONFIG_MEDIA_TUNER_QT1010 is not set
# CONFIG_MEDIA_TUNER_XC2028 is not set
# CONFIG_MEDIA_TUNER_XC5000 is not set
# CONFIG_MEDIA_TUNER_MXL5005S is not set
# CONFIG_MEDIA_TUNER_MXL5007T is not set
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
# CONFIG_VIDEO_VIVI is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_SOC_CAMERA is not set
#
# Qualcomm MSM Camera And Video
#
CONFIG_MSM_CAMERA=y
# CONFIG_MSM_CAMERA_DEBUG is not set
#
# Camera Sensor Selection
#
# CONFIG_MT9T013 is not set
# CONFIG_MT9D112 is not set
# CONFIG_MT9P012 is not set
CONFIG_S5K3E2FX=y
CONFIG_RADIO_ADAPTERS=y
# CONFIG_RADIO_TEA5764 is not set
CONFIG_DAB=y
#
# Graphics support
#
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=y
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
# CONFIG_FB_BOOT_VESA_SUPPORT is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set
#
# Frame buffer hardware drivers
#
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_MB862XX is not set
CONFIG_FB_MSM=y
CONFIG_FB_MSM_LCDC=y
CONFIG_GPU_MSM_KGSL=y
CONFIG_MSM_KGSL_MMU=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
# CONFIG_LCD_ILI9320 is not set
CONFIG_LCD_PLATFORM=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_GENERIC is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE is not set
# CONFIG_LOGO is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
#
# Special HID drivers
#
CONFIG_HID_COMPAT=y
# CONFIG_HID_APPLE is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
# CONFIG_USB_ARCH_HAS_EHCI is not set
# CONFIG_USB is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# Enable Host or Gadget support to see Inventra options
#
#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
#
# CONFIG_USB_GADGET is not set
#
# OTG and related infrastructure
#
#
# USB Function Support
#
CONFIG_USB_FUNCTION=y
CONFIG_USB_FUNCTION_MSM_HSUSB=y
# CONFIG_USB_FUNCTION_NULL is not set
# CONFIG_USB_FUNCTION_ZERO is not set
# CONFIG_USB_FUNCTION_LOOPBACK is not set
CONFIG_USB_FUNCTION_ADB=y
# CONFIG_USB_FUNCTION_UMS is not set
CONFIG_USB_FUNCTION_MASS_STORAGE=y
CONFIG_USB_FUNCTION_DIAG=y
# CONFIG_USB_FUNCTION_SERIAL is not set
CONFIG_USB_FUNCTION_ETHER=y
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_UNSAFE_RESUME=y
CONFIG_MMC_EMBEDDED_SDIO=y
CONFIG_MMC_PARANOID_SD_INIT=y
#
# MMC/SD/SDIO Card Drivers
#
CONFIG_MMC_BLOCK=y
# CONFIG_MMC_BLOCK_BOUNCE is not set
CONFIG_MMC_BLOCK_DEFERRED_RESUME=y
# CONFIG_SDIO_UART is not set
# CONFIG_MMC_TEST is not set
#
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
CONFIG_MMC_MSM7X00A=y
# CONFIG_MMC_MSM7X00A_RESUME_IN_WQ is not set
# CONFIG_MEMSTICK is not set
# CONFIG_ACCESSIBILITY is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
#
# LED drivers
#
# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_CPLD=y
# CONFIG_LEDS_PCA955X is not set
#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
CONFIG_LEDS_TRIGGER_SLEEP=y
CONFIG_SWITCH=y
CONFIG_SWITCH_GPIO=y
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set
#
# RTC interfaces
#
# CONFIG_RTC_INTF_SYSFS is not set
# CONFIG_RTC_INTF_PROC is not set
# CONFIG_RTC_INTF_DEV is not set
CONFIG_RTC_INTF_ALARM=y
CONFIG_RTC_INTF_ALARM_DEV=y
# CONFIG_RTC_DRV_TEST is not set
#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
# CONFIG_RTC_DRV_DS1374 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
#
# SPI RTC drivers
#
#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_MSM7X00A=y
# CONFIG_DMADEVICES is not set
CONFIG_REGULATOR=y
CONFIG_REGULATOR_DEBUG=y
# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
# CONFIG_REGULATOR_BQ24022 is not set
CONFIG_REGULATOR_TPS65023=y
# CONFIG_UIO is not set
CONFIG_STAGING=y
# CONFIG_STAGING_EXCLUDE_BUILD is not set
# CONFIG_MEILHAUS is not set
# CONFIG_ECHO is not set
# CONFIG_AGNX is not set
# CONFIG_COMEDI is not set
#
# Android
#
CONFIG_ANDROID=y
CONFIG_ANDROID_BINDER_IPC=y
CONFIG_ANDROID_LOGGER=y
CONFIG_ANDROID_RAM_CONSOLE=y
CONFIG_ANDROID_RAM_CONSOLE_ENABLE_VERBOSE=y
CONFIG_ANDROID_RAM_CONSOLE_ERROR_CORRECTION=y
CONFIG_ANDROID_RAM_CONSOLE_ERROR_CORRECTION_DATA_SIZE=128
CONFIG_ANDROID_RAM_CONSOLE_ERROR_CORRECTION_ECC_SIZE=16
CONFIG_ANDROID_RAM_CONSOLE_ERROR_CORRECTION_SYMBOL_SIZE=8
CONFIG_ANDROID_RAM_CONSOLE_ERROR_CORRECTION_POLYNOMIAL=0x11d
# CONFIG_ANDROID_RAM_CONSOLE_EARLY_INIT is not set
CONFIG_ANDROID_TIMED_OUTPUT=y
CONFIG_ANDROID_TIMED_GPIO=y
CONFIG_ANDROID_LOW_MEMORY_KILLER=y
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_EXT4_FS=y
CONFIG_EXT4DEV_COMPAT=y
CONFIG_EXT4_FS_XATTR=y
CONFIG_EXT4_FS_POSIX_ACL=y
CONFIG_EXT4_FS_SECURITY=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=y
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_DNOTIFY is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
# CONFIG_MSDOS_FS is not set
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
CONFIG_MISC_FILESYSTEMS=y
CONFIG_YAFFS_FS=y
CONFIG_YAFFS_YAFFS1=y
CONFIG_YAFFS_YAFFS2=y
CONFIG_YAFFS_AUTO_YAFFS2=y
CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
CONFIG_NETWORK_FILESYSTEMS=y
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
#
# Kernel hacking
#
CONFIG_PRINTK_TIME=y
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_DEBUG_SLAB=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_VM=y
CONFIG_DEBUG_SG=y
CONFIG_FRAME_POINTER=y
CONFIG_HAVE_FUNCTION_TRACER=y
#
# Tracers
#
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_DEBUG_ERRORS=y
#
# Security options
#
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
CONFIG_CRYPTO_AUTHENC=y
#
# Authenticated Encryption with Associated Data
#
#
# Block modes
#
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_ECB=y
#
# Hash modes
#
CONFIG_CRYPTO_HMAC=y
#
# Digest
#
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
#
# Ciphers
#
CONFIG_CRYPTO_AES=y
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_TWOFISH_COMMON=y
#
# Compression
#
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_LZO is not set
#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_REED_SOLOMON=y
CONFIG_REED_SOLOMON_ENC8=y
CONFIG_REED_SOLOMON_DEC8=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=y
CONFIG_TEXTSEARCH_BM=y
CONFIG_TEXTSEARCH_FSM=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
Gentoo works well with any kernel. So easy way is to wait for the next kernel (android back into next linux kernel : http://www.theregister.co.uk/2010/02/03/android_driver_code_deleted_from_linux_kernel/)
Furthermore, I believe ramdisk fs must be specific (explore an boot.img or read this: http://android-dls.com/wiki/index.php?title=HOWTO:_Unpack,_Edit,_and_Re-Pack_Boot_Images)
If you're not running an android kernel you're probably going to run into a lot of trouble, especially with drivers. Considering the android code isn't checked into the mainline linux kernel, this isn't very surprising.
You could make an ebuild that grabs the kernel source from android's git
and go from there. http://android.git.kernel.org/
Or you could build on your desktop and simply copy the kernel files over to the device which is what I do with the debian setup.
Jairuncloth: but the android checkout isn't linux compatible, is it? We need the standardized /dev for mesh networking...
Also, how did you get your .config to work? I'm assuming you compiled a stock kernel, yes? Have you re-done it for 2.6.33 or .34?
What is the advantage of genoo on the phone?
I considered a few distros to boot on the phone, i thought having to compile all your **** from source on the phone would be a complete nightmare, wouldn't a pre-packaged debian be much much more practical?
Advantage of compiling binaries
There are a number of reasons why pre-compiled binaries are a bit of a waste. Software hooks for software you never intend to connect, catch-all generic processor calls, non-utilization of optimization routines for specific hardware. Maybe not such a big deal on a computer, but on an embedded platform, can be extremely helpful.
And I am not going to be using this thing as a phone at all. It's going to be used as an embedded linux platform.
Are you compiling directly on the phone ?
It won't solve your problems as it is (android)kernel related but cross-compiling on a PC and archiving the built stuff with quickpkg seems to me a better solution to add stuff in the distro.
It will be pre-compiled in a way but without the bloat usually found for example in debian packages (no fanboi stuff here, just old experiences)...
Just my 2 cents...
Yes, we natively compile on the phone. You set it up (which is the hardest part), go to sleep, wake up, voila, stuff done.
The problem I would have is getting Gentoo to recognize that a package has been installed so it would maintain it...plus, once you get the compiler and libraries on there, you might as well compile it natively.
Plus, Gentoo handles all of the dependencies. revdep-rebuild is POWERFUL in that way.
HMM
IDK if anyone else has tried this but i was sitting in class and found a version of linux that is specified for the ARM processors called ARMed by slackware and idk much about this but i was just trying to share this knowledge
Slackware for ARM
http://www.armedslack.org/
Stock Linux
Problem isn't a distro for ARM....problem is getting the linux kernel up and running....
I've got the distro running inside of an android chroot. It's getting .33 or .34 kernel working right that is a PITA.
joelinux said:
Jairuncloth: but the android checkout isn't linux compatible, is it? We need the standardized /dev for mesh networking...
Also, how did you get your .config to work? I'm assuming you compiled a stock kernel, yes? Have you re-done it for 2.6.33 or .34?
Click to expand...
Click to collapse
I used the android kernel for running debian. I haven't made any attempts at getting a stock kernel working.
You may have better luck with a code aurora kernel then stock. If you know what you are doing, you could port their drivers to a stock kernel. Most of that stuff is over my head. I just know the android kernel appears to work fine with debian.
Really? I need access to the SPI and i2c busses. I also need the ethernet card to be stock so we can run open802.11s on it.
I'll try it your way...
You shouldn't have any issue running Gentoo with the Cyanogen kernel or the MSM kernel off CodeAurora. Debian runs fine.
I2C works (take a look at msm-i2c) and SPI is provided as well (look at SPI_qsd). I'm not sure if the WiFi driver is going to support open802.11s but you can take a look. A "vanilla" kernel.org kernel will never work until/unless CodeAurora and the Qualcomm MSM/QSD tree hit mainline, but that doesn't matter as Android kernels are in no way "not Linux compatible" - the delta between an Android-patched kernel and a stock kernel is very small, especially as things like binder and lowmemorykiller hit mainline.
You can probably just compile the CodeAurora kernel with all of the Android options (PMEM, LowMemoryKiller, binder, adb, logger) disabled, but I don't know why you would even bother as a normal userland will run fine on an "Android kernel."
I'd also like to point out that compiling on the phone is a poor idea unless you have your compile on external storage (with the N1, I'd imagine that would mean NFS). Otherwise, you're going to end up with a very slow filesystem (many tiny files smaller than a NAND block does not do good things for flash filesystems) and worn-out flash. Personally, I'd just build a cross-toolchain and cross-compile - it'll be orders of magnitude faster and you won't have to worry about issues like NAND and heat while compiling.
Hello!
I was hoping someone could help me create an edify file for dsixda's Kitchen to get the S3 working in the kitchen.
I don't know all these mount points etc.
#
# The values below should be set in each file in this folder.
#
# Each file represents a device name (set in ro.product.device of
# build.prop)
#
# If yes, then this device requires changing the mount point
# names in the new updater-script or update-script
# DO NOT SET TO 'yes' IF DEVICE IS BY DELL
change_mnt=no
# If yes, the device is by Dell and requires changing the mount
# point names in the new updater-script or update-script
change_mnt_dell=no
#
# NOTE: The update-script will be converted to updater-script if the
# definition file for the device exists. If 'change_mnt' or
# 'change_mnt_dell' are set to 'yes' then the mount names will
# also be changed.
#
# Mention the mount point names if change_mnt=yes
# Use '\/' instead of '/'
# e.g. sys_mnt=\/dev\/block\/mcblk0p25
#
# If unknown, set to: ???
sys_mnt=
cache_mnt=
boot_mnt=
data_mnt=
sdcard_mnt=
# Set this mount point for the modem.bin in Samsung devices like the Galaxy S2
modem_mnt=
# Set this mount point if you know what it is (e.g. on Motorola Atrix)
webtop_mnt=
# Filesystem info for SYSTEM/DATA/CACHE/etc.
# e.g. param1=ext3, param2=EMMC
param1=
param2=
# If SDCARD filesystem is different from above, then mention it
# e.g. param1_sdcard=vfat, param2_sdcard=MTD
param1_sdcard=
param2_sdcard=
# If CACHE filesystem is different from above, then mention it
param1_cache=
param2_cache=
# If yes, the device does not require using a 'tmp' folder when
# flashing the boot.img in the updater-script
#
# e.g. package_extract_file("boot.img", "/dev/block/blah1");
fix_boot=no
# If yes, the device requires a 'tmp' folder when flashing the
# boot.img in the updater-script, PLUS the boot partition name
# needs to be used, rather than just 'boot'
#
# e.g. Replace: write_raw_image("/tmp/boot.img", "boot")
# with: write_raw_image("/tmp/boot.img", "/dev/block/blah1")
fix_boot2=no
# If yes, the device requires a 'dd' command to write the boot.img
#
# e.g. Replace: write_raw_image("/tmp/boot.img", "boot")
# with: run_program("/sbin/busybox", "dd", "if=/tmp/boot.img", "of=/dev/block/blah")
fix_boot3=no
# Device uses /cache instead of /tmp, e.g. when writing boot.img
use_cache_not_tmp=no
Help is appreciated.
Regards,
dejong12
Has any one been able to set SElinux to permissive from enforcing?
I have tried this
Code:
[email protected]:/ $ su
[email protected]:/ # pm disable com.sec.knox.seandroid
[email protected]:/ # setenforce 0
[email protected]:/ #
With the output of
Code:
[email protected]:/ $ su
[email protected]:/ # pm disable com.sec.knox.seandroid
pm disable com.sec.knox.seandroid
Package com.sec.knox.seandroid new state: disabled
[email protected]:/ # setenforce 0
setenforce 0
[email protected]:/ #
But SElinux is still showing enforcing.
Other methods I was trying was editing /etc/selinux/. This location does not exists.
I have also searched other sources, and non work for this particular build of S4.
I do not believe i can edit the md5 file and get it to flash after the mods.
Rippey574 said:
Has any one been able to set SElinux to permissive from enforcing?
I have tried this
Code:
[email protected]:/ $ su
[email protected]:/ # pm disable com.sec.knox.seandroid
[email protected]:/ # setenforce 0
[email protected]:/ #
With the output of
Code:
[email protected]:/ $ su
[email protected]:/ # pm disable com.sec.knox.seandroid
pm disable com.sec.knox.seandroid
Package com.sec.knox.seandroid new state: disabled
[email protected]:/ # setenforce 0
setenforce 0
[email protected]:/ #
But SElinux is still showing enforcing.
Other methods I was trying was editing /etc/selinux/. This location does not exists.
I have also searched other sources, and non work for this particular build of S4.
I do not believe i can edit the md5 file and get it to flash after the mods.
Click to expand...
Click to collapse
try
Code:
su
cd /system
set enforce 0
getenforce
Didn't work
[email protected]:/ $ su
[email protected]:/ # cd /system
[email protected]:/system # set enforce 0
[email protected]:/system # getenforce
Enforcing
[email protected]:/system #
Sent from my SCH-I545 using xda app-developers app
I found this in the int.rc file, I believe if I # these out, it would stop the setenforce lockout. I tried editing SElinux to 0, but it won't keep the saves. Even with permission changes on the file. Any thoughts on this?
Code:
# Configure SEAndroid booleans and enforcing mode
setsebool debugf# Configure SEAndroid booleans and enforcing mode
setsebool debugfs 1s 1
# create mountpoints
mkdir /mnt 0775 root system
# Allow system UID to setenforce and set booleans.
chown system system /selinux/enforce
chown system system /sys/fs/selinux/enforce
chown -R system system /selinux/booleans
chown -R system system /sys/fs/selinux/booleans
chown system system /selinux/commit_pending_bools
chown system system /sys/fs/selinux/commit_pending_bools
on init
sysclktz 0
loglevel 3
Rippey574 said:
I found this in the int.rc file, I believe if I # these out, it would stop the setenforce lockout. I tried editing SElinux to 0, but it won't keep the saves. Even with permission changes on the file. Any thoughts on this?
Code:
# Configure SEAndroid booleans and enforcing mode
setsebool debugf# Configure SEAndroid booleans and enforcing mode
setsebool debugfs 1s 1
# create mountpoints
mkdir /mnt 0775 root system
# Allow system UID to setenforce and set booleans.
chown system system /selinux/enforce
chown system system /sys/fs/selinux/enforce
chown -R system system /selinux/booleans
chown -R system system /sys/fs/selinux/booleans
chown system system /selinux/commit_pending_bools
chown system system /sys/fs/selinux/commit_pending_bools
on init
sysclktz 0
loglevel 3
Click to expand...
Click to collapse
What exactly are you trying to achieve? The information you want shouldn't be publicly posted. Well not yet anyways, because the ability to set SElinux to Permissive longer than just temporarily is probably needed to get safestrap working.
Sent from my SCH-I535 using XDA Premium 4 mobile app
I need it to be on when I want, as I want. It to be. It's preventing my customization of my rom. It really limits what you can do in fine detail. And quite frankly that destroys the beauty of Android!
Besides the fact it will controls my ability to slightly change something I own. If I wanted that I would go with Apple. But that's a completely different rant lol.
I use Linux, raptor and c, never dabbled in java so some of the things are different to me.
I would even take a working way to disable it temporarily.
Sent from my SCH-I545 using xda app-developers app
I would like some help in modifying my stock rom to include the SuperSU apk and all five su binaries (su, daemonsu, sukernel, supolicy and suinit).
I am aware that there are multiple tutorials out there for this kind of thing but what I'm trying to do requires the system be repacked into a sparse image to flash through fastboot as the phone has no TWRP build available.
Thank You.
Bythos73 said:
I would like some help in modifying my stock rom to include the SuperSU apk and all five su binaries (su, daemonsu, sukernel, supolicy and suinit).
I am aware that there are multiple tutorials out there for this kind of thing but what I'm trying to do requires the system be repacked into a sparse image to flash through fastboot as the phone has no TWRP build available.
Thank You.
Click to expand...
Click to collapse
Hello, you can unzip the flashable SuperSu zip and take a look at the update-binary script, this will shed some light on how the installation works, for example this is an excerpt taken from version 2.82:
Code:
#!/sbin/sh
#
# SuperSU installer ZIP
# Copyright (c) 2012-2017 - Chainfire, CCMT
#
# ----- GENERIC INFO ------
#
# The following su binary versions are included in the full package. Each
# should be installed only if the system has the same or newer API level
# as listed. The script may fall back to a different binary on older API
# levels. supolicy are all ndk/pie/19+ for 32 bit, ndk/pie/20+ for 64 bit.
#
# binary ARCH/path build type API
#
# arm-v5te arm ndk non-pie 7+
# x86 x86 ndk non-pie 7+
#
# x86 x86 ndk pie 17+ (su.pie, naming exception)
# arm-v7a armv7 ndk pie 17+
# mips mips ndk pie 17+
#
# arm64-v8a arm64 ndk pie 20+
# mips64 mips64 ndk pie 20+
# x86_64 x64 ndk pie 20+
#
# Non-static binaries are supported to be PIE (Position Independent
# Executable) from API level 16, and required from API level 20 (which will
# refuse to execute non-static non-PIE).
#
# The script performs several actions in various ways, sometimes
# multiple times, due to different recoveries and firmwares behaving
# differently, and it thus being required for the correct result.
#
# Overridable variables (shell):
# BIN - Location of architecture specific files (native folder)
# COM - Location of common files (APK folder)
# LESSLOGGING - Reduce ui_print logging (true/false)
# NOOVERRIDE - Do not read variables from /system/.supersu or
# /data/.supersu
#
# Overridable variables (shell, /system/.supersu, /cache/.supersu,
# /data/.supersu):
# SYSTEMLESS - Do a system-less install? (true/false, 6.0+ only)
# PATCHBOOTIMAGE - Automatically patch boot image? (true/false,
# SYSTEMLESS only)
# BOOTIMAGE - Boot image location (PATCHBOOTIMAGE only)
# STOCKBOOTIMAGE - Stock boot image location (PATCHBOOTIMAGE only)
# BINDSYSTEMXBIN - Poor man's overlay on /system/xbin (true/false,
# SYSTEMLESS only)
# PERMISSIVE - Set sepolicy to fake-permissive (true/false, PATCHBOOTIMAGE
# only)
# KEEPVERITY - Do not remove dm-verity (true/false, PATCHBOOTIMAGE only)
# KEEPFORCEENCRYPT - Do not replace forceencrypt with encryptable (true/
# false, PATCHBOOTIMAGE only)
# REMOVEENCRYPTABLE - Remove the encryptable flag, needed on newer
# Samsung devices to disable forced encryption
# (true/false, PATCHBOOTIMAGE only)
# FRP - Place files in boot image that allow root to survive a factory
# reset (true/false, PATCHBOOTIMAGE only). Reverts to su binaries
# from the time the ZIP was originall flashed, updates are lost.
# Shell overrides all, /data/.supersu overrides /cache/.supersu overrides
# /system/.supersu
#
# Note that if SELinux is set to enforcing, the daemonsu binary expects
# to be run at startup (usually from install-recovery.sh, 99SuperSUDaemon,
# app_process, or init.supersu.rc) from u:r:supersu:s0 (7.0+), u:r:init:s0 or
# u:r:kernel:s0 contexts. Depending on the current policies, it can also
# deal with u:r:init_shell:s0 and u:r:toolbox:s0 contexts. Any other context
# will lead to issues eventually.
#
# ----- "SYSTEM" INSTALL -----
#
# "System" install puts all the files needed in /system and does not need
# any boot image modifications. Default install method pre-Android-6.0
# (excluding Samsung-5.1).
#
# Even on Android-6.0+, the script attempts to detect if the current
# firmware is compatible with a system-only installation (see the
# "detect_systemless_required" function), and will prefer that
# (unless the SYSTEMLESS variable is set) if so. This will catch the
# case of several custom ROMs that users like to use custom boot images
# with - SuperSU will not need to patch these. It can also catch some
# locked bootloader cases that do allow security policy updates.
#
# To install SuperSU properly, aside from cleaning old versions and
# other superuser-type apps from the system, the following files need to
# be installed:
#
# API source target chmod chcon required
#
# 7-19 common/Superuser.apk /system/app/Superuser.apk 0644 u:object_r:system_file:s0 gui
# 20+ common/Superuser.apk /system/app/SuperSU/SuperSU.apk 0644 u:object_r:system_file:s0 gui
#
# 17+ common/install-recovery.sh /system/etc/install-recovery.sh 0755 *1 required
# 17+ /system/bin/install-recovery.sh (symlink to /system/etc/...) required
# *1: same as /system/bin/toolbox: u:object_r:system_file:s0 if API < 20, u:object_r:toolbox_exec:s0 if API >= 20
#
# 7+ ARCH/su *2 /system/xbin/su *3 u:object_r:system_file:s0 required
# 7+ /system/bin/.ext/.su *3 u:object_r:system_file:s0 gui
# 17+ /system/xbin/daemonsu 0755 u:object_r:system_file:s0 required
# *2: su.pie for 17+ x86(_32) only
# *3: 06755 if API < 18, 0755 if API >= 18
#
# 19+ ARCH/supolicy /system/xbin/supolicy 0755 u:object_r:system_file:s0 required
# 19+ ARCH/libsupol.so /system/lib(64)/libsupol.so 0644 u:object_r:system_file:s0 required
#
# 21+ /system/bin/app_process32 *5 /system/bin/app_process32_original 0755 u:object_r:zygote_exec:s0 required
# 21+ /system/bin/app_process64 *5 /system/bin/app_process64_original 0755 u:object_r:zygote_exec:s0 required
# 21+ /system/bin/app_processXX *5 /system/bin/app_process_init 0755 u:object_r:system_file:s0 required
# 21+ /system/bin/app_process (symlink to /system/xbin/daemonsu) required
# 21+ *5 /system/bin/app_process32 (symlink to /system/xbin/daemonsu) required
# 21+ *5 /system/bin/app_process64 (symlink to /system/xbin/daemonsu) required
# *5: Only do this for the relevant bits. On a 64 bits system, leave the 32 bits files alone, or dynamic linker errors
# will prevent the system from fully working in subtle ways. The bits of the su binary must also match!
#
# 17+ common/99SuperSUDaemon *6 /system/etc/init.d/99SuperSUDaemon 0755 u:object_r:system_file:s0 optional
# *6: only place this file if /system/etc/init.d is present
#
# 17+ 'echo 1 >' or 'touch' *7 /system/etc/.installed_su_daemon 0644 u:object_r:system_file:s0 optional
# *7: the file just needs to exist or some recoveries will nag you. Even with it there, it may still happen.
#
# It may seem some files are installed multiple times needlessly, but
# it only seems that way. Installing files differently or symlinking
# instead of copying (unless specified) will lead to issues eventually.
#
# After installation, run '/system/xbin/su --install', which may need to
# perform some additional installation steps. Ideally, at one point,
# a lot of this script will be moved there.
#
# The included chattr(.pie) binaries are used to remove ext2's immutable
# flag on some files. This flag is no longer set by SuperSU's OTA
# survival since API level 18, so there is no need for the 64 bit versions.
# Note that chattr does not need to be installed to the system, it's just
# used by this script, and not supported by the busybox used in older
# recoveries.
#
# ----- "SYSTEM-LESS" INSTALL -----
#
# "System-less" install requires a modified boot image (the script can patch
# many boot images on-the-fly), but does not touch /system at all. Instead
# it keeps all the needed files in an image (/data/su.img) which is mounted
# to /su. Default install method on all Android-6.0+ and Samsung-5.1+
# devices.
#
# Note that even on 6.0+, system compatibility is checked. See the "SYSTEM"
# install section above.
#
# An ext4 image is created as /data/su.img, or /cache/su.img if /data could
# not be mounted. Similarly, the APK is placed as either /data/SuperSU.apk
# or /cache/SuperSU.apk. This is so we are not dependent on /data decryption
# working in recovery, which in the past has proved an issue on brand-new
# Android versions and devices.
#
# /sbin/launch_daemonsu.sh, which is added a service to init.rc, will mount
# the image at /su, and launch daemonsu from /su/bin/daemonsu. But before it
# does that, it will try to merge /data/su.img and /cache/su.img (leading),
# if both are present. It will also try to install the SuperSU APK.
#
# Files are expected at the following places (/su being the mountpoint of
# the ext4 image):
#
# API source target chmod chcon required
#
# 22+ common/Superuser.apk /[data|cache]/SuperSU.apk 0644 u:object_r:system_file:s0 gui
#
# 22+ ARCH/su *1 /su/bin/su 0755 u:object_r:system_file:s0 required
# 22+ /su/bin/daemonsu 0755 u:object_r:system_file:s0 required
# *1: su.pie for 17+ x86(_32) only
#
# 22+ ARCH/supolicy /su/bin/supolicy_wrapped 0755 u:object_r:system_file:s0 required
# 22+ /su/bin/su (symlink) *2 /su/bin/supolicy 0755 u:object_r:system_file:s0 required
# 22+ ARCH/libsupol.so /su/lib/libsupol.so 0644 u:object_r:system_file:s0 required
# *2: when called this way, su sets the correct LD_LIBRARY_PATH and calls supolicy_wrapped
#
# 22+ ARCH/sukernel /su/bin/sukernel 0755 u:object_r:system_file:s0 required
#
# These files are automatically created on launch by daemonsu as needed:
# 22+ /system/bin/sh /su/bin/sush 0755 u:object_r:system_file:s0 required
# 22+ /system/bin/app_process[64] /su/bin/app_process 0755 u:object_r:system_file:s0 required
#
# These files are injected into the boot image ramdisk:
# 22+ common/launch_daemonsu.sh /sbin/launch_daemonsu.sh 0700 u:object_r:rootfs:s0 required
#
# On devices where / is in the system partition:
# 22+ ARCH/suinit /init 0750 u:object_r:rootfs:s0 required
#
# The automated boot image patcher included makes the following modifications
# to the ramdisk:
#
# - Uses the supolicy tool to patch the sepolicy file
# - Injects /sbin/launch_daemon.sh
# - Creates /su
# - Removes /verity_key
# - Patches /*fstab*
# --- Removes support_scfs and verify flags
# --- Changes forceencrypt/forcefdeorfbe into encryptable
# --- Set ro mounts to use noatime
# - Patches /init.rc
# --- Removes 'setprop selinux.reload_policy' occurences
# --- Adds a SuperSU:PATCH marker with the version of the sukernel tool
# --- Adds a SuperSU:STOCK marker listed the SHA1 of the original boot image
# - Adds /init.supersu.rc
# --- Adds a sukernel.mount property trigger that mounts /data/su.img to /su
# --- Adds the daemonsu service that launches /sbin/launch_daemon.sh
# --- Adds exec /sbin/launch_daemonsu.sh on post-fs-data
# - Patches /init.environ.rc
# --- Adds PATH variable if it does not exist
# --- Prepends /su/bin to the PATH variable
# - Patches /*.rc
# --- Adds a seclabel to services and execs that are missing one
# - In case the device has the root directory inside the system partition:
# --- /system_root contents are copied to /boot
# --- All files mentioned above are modified in /boot instead of /
# --- /boot/*fstab* is modified to mount / to /system_root, and
# bind-mount /system to /system_root/system
# --- Kernel binary is patched to load from initramfs instead of system
#
# In case this documentation becomes outdated, please note that the sukernel
# tool is very chatty, and its output tells you exactly what it is doing
# and how. In TWRP, you can view this output by catting /tmp/recovery.log
# after flashing the ZIP.
#
# The boot image patcher creates a backup of the boot image it patches, for
# future restoration. It cannot re-patch a patched boot image, it will restore
# the previous boot image first. /[data|cache]/stock_boot_*.gz
#
# The boot image patcher currently only supports GZIP compressed ramdisks, and
# boot images in the standard Android boot image format.
#
# During boot image patch, /data/custom_ramdisk_patch.sh will be called,
# with the name of the ramdisk cpio file as parameter. The script must
# replace the input file and return a 0 exit code.
#
# Just before flashing, the boot image patcher will call
# /data/custom_boot_image_patch.sh with the name of the patched boot image
# as parameter. A device-specific patcher can further patch the boot image
# if needed. It must replace the input file and return a 0 exit code.
OUTFD=$2
ZIP=$3
getvar() {
local VARNAME=$1
local VALUE=$(eval echo \$"$VARNAME");
for FILE in /data/.supersu /cache/.supersu /system/.supersu; do
if [ -z "$VALUE" ]; then
LINE=$(cat $FILE 2>/dev/null | grep "$VARNAME=")
if [ ! -z "$LINE" ]; then
VALUE=${LINE#*=}
fi
fi
done
eval $VARNAME=\$VALUE
}
readlink /proc/$$/fd/$OUTFD 2>/dev/null | grep /tmp >/dev/null
if [ "$?" -eq "0" ]; then
# rerouted to log file, we don't want our ui_print commands going there
OUTFD=0
# we are probably running in embedded mode, see if we can find the right fd
# we know the fd is a pipe and that the parent updater may have been started as
# 'update-binary 3 fd zipfile'
for FD in `ls /proc/$$/fd`; do
readlink /proc/$$/fd/$FD 2>/dev/null | grep pipe >/dev/null
if [ "$?" -eq "0" ]; then
ps | grep " 3 $FD " | grep -v grep >/dev/null
if [ "$?" -eq "0" ]; then
OUTFD=$FD
break
fi
fi
done
fi
ui_print_always() {
echo -n -e "ui_print $1\n" >> /proc/self/fd/$OUTFD
echo -n -e "ui_print\n" >> /proc/self/fd/$OUTFD
}
if [ -z "$LESSLOGGING" ]; then
LESSLOGGING=false
fi
UI_PRINT_LAST=""
ui_print() {
if (! $LESSLOGGING); then
UI_PRINT_LAST="$1"
ui_print_always "$1"
fi
}
ui_print_less() {
if ($LESSLOGGING); then
ui_print_always "$1"
fi
}
ch_con() {
LD_LIBRARY_PATH=$SYSTEMLIB /system/bin/toybox chcon -h u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
LD_LIBRARY_PATH=$SYSTEMLIB /system/toolbox chcon -h u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
LD_LIBRARY_PATH=$SYSTEMLIB /system/bin/toolbox chcon -h u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
chcon -h u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
LD_LIBRARY_PATH=$SYSTEMLIB /system/bin/toybox chcon u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
LD_LIBRARY_PATH=$SYSTEMLIB /system/toolbox chcon u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
LD_LIBRARY_PATH=$SYSTEMLIB /system/bin/toolbox chcon u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
chcon u:object_r:system_file:s0 $1 1>/dev/null 2>/dev/null
}
ch_con_ext() {
LD_LIBRARY_PATH=$SYSTEMLIB /system/bin/toybox chcon $2 $1 1>/dev/null 2>/dev/null
LD_LIBRARY_PATH=$SYSTEMLIB /system/toolbox chcon $2 $1 1>/dev/null 2>/dev/null
LD_LIBRARY_PATH=$SYSTEMLIB /system/bin/toolbox chcon $2 $1 1>/dev/null 2>/dev/null
chcon $2 $1 1>/dev/null 2>/dev/null
}
Thanks for the quick response. I have attempted to copy some of the files stated in excerpt to my system image but it seems that I might have missed a few. But I see it stating some chcon commands so I'm just wondering if it'd be possible to chcon the files needed on a linux pc and have it work.
Bythos73 said:
Thanks for the quick response. I have attempted to copy some of the files stated in excerpt to my system image but it seems that I might have missed a few. But I see it stating some chcon commands so I'm just wondering if it'd be possible to chcon the files needed on a linux pc and have it work.
Click to expand...
Click to collapse
I'm not sure what will happen if you run those chcon commands, what happened when you tried it?
Yup, this manual way may be a bit tricky
http://su.chainfire.eu/#embed said:
6. Embedding
6.1. Files
All the files you need are in the latest SuperSU flashable ZIP. The latest 'stable' build can always be retrieved from my server, for the latest 'beta' release you need to check the beta thread in the SuperSU forums.
The installation script inside the ZIP is META-INF/com/google/android/update-binary. This is not a binary as the name suggests, but a shell script, and the standard update ZIP's updater-script file is just a dummy.
This script has comments which document which files go where on which API level, and what their file permissions, ownerhips, and security labels must be. If you have done this exactly right, SuperSU will not complain when you open the app after booting.
6.2. Custom ROMs
It is non-trivial to include SuperSU exactly right on your own. It is therefore often easiest to include the latest SuperSU ZIP inside your own flashable ZIP, and chain its installation.
Click to expand...
Click to collapse
Can you tell us a bit more about your device model & android version, and which files you copied/commands you ran so far?
What errors if any do you get after flashing your modified img?
I secretly hope a custom recovery exists for your device, or porting one proves easier :fingers-crossed:
I'm repacking the image now using img2simg for my first boot attempt.
I have an Alcatel 3 5052A, Device CodeName A3A running Android Oreo 8.1.0. So far I don't believe I can get a custom recovery for this device as the line of devices that this phone was released with seem to have a bootloader which doesn't boot unsigned images, nevermind the fact that it's impossible to flash any partition other than system through fastboot. It's a real pain. Thankfully it does boot GSIs like Phh-Treble so not all hope is lost on that front.
I've copied the su and supolicy binaries, I got daemonsu by copying the su bin, I also copied the SuperSU apk and the libsupol.so library into all of their respective directories.
It has booted but no su, and SuperSU was not in the Launcher so I'm gonna retry it.
Don't give up! there are lots of avenues yet to explore if you want to give the manual method a rest for a while.
What do you get when you try unlocking the bootloader from fastboot?
Are you familiar with SP Flash tools? This is an alternative way to flash images onto various MTK devices.
I see the build.prop has these options but im unsure what values to use:
######## UBOOTENV VARIBLES - r/w as system properties ##########
#
# Now we can load ubootenv varibles to system properties.
# We use a special prefix ("ubootenv.var" as default) to indicate that the 'property'
# actually is an ubootenv varible.
#
# A ubootenv 'property' will be initialized during system booting. And when user set
# a different value, it will be written back to ubootenv device immediately.
#
## prefix of ubootenv varibles - should less than 16 chars.
#UBOOTENV MTD NAME
#ubootenv.var.bootcmd=
#ubootenv.var.cpuclock=
#ubootenv.var.gpuclock=
Click to expand...
Click to collapse
Then init.amlogic.board.rc has these settings:
on early-init
loglevel 3
write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor performance
write /sys/class/freq_limit/limit 0
write /sys/devices/system/cpu/cpu0/cpufreq/scaling_dflt_freq 2016000
mount configfs configfs /sys/kernel/config
#mount usbfs none /proc/bus/usb
insmod /boot/aml_nftl_dev.ko
insmod /boot/optee.ko
insmod /boot/optee_armtz.ko
on init
on property:dev.bootcomplete=1
write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor interactive
on post-fs-data
insmod /system/lib/mali.ko mali_debug_level=2 mali_shared_mem_size=0x40000000
on boot
setprop ro.radio.noril true
#write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor interactive
#write /sys/class/freq_limit/limit 0
#write /sys/devices/system/cpu/cpu0/cpufreq/scaling_dflt_freq 2016000
Click to expand...
Click to collapse
Any help would be appreciated.