Hello,
I actually have successfully build some kernels. Mainly, this is the linux way:
- get kernel sources
- get hardware specific changes
- get the toolchain -> i'm using google prebuilt tree, with ARM tool chain 4.4.3 already compiled
- build with usual steps: def_config, configure, kernel, modules
All is ok.
Now, i found Android.mk files. Precisely, a previous kernel, with sensors related to my device, that i would like to port.
But here comes the trouble. I have hard time to do the link between Linux kernel for ARM and Android makefile. I don't see how it goes with my kernel, how i could compile this using the prebuilt tools i could grab from Google.
In short, how to include .mk files into a classic kernel ? What should i get in the end ? A module ? A replacement binary ? More precisely, what is exactly NDK and where it stands in the above layers ?
ARM Linux Kernel <--> Dalvik JVM <--> APK
Last, is it possible with Google prebuilt to compile the .mk without referencing your kernel ?
Thank you !
Thank you for your help
Damn ! Either the questions is too obvious, either it is too complex. Any help ?
Self reply: downloading the NDK is mandatory
- you can use your favorite toolchain, provided with the NDK
- you can embed the .mk into your application, for Eclipse / Android studio, it will use the NDK to compile
Hello!
This is a development thread for the project of upgrading of the Linux kernel for the U8500 platform.
Builds provided here (at the moment of writing this message) are not considered to be used as a daily driver, by any means, - these are rather a dev preview versions.
For now, there are a several LK builds (the highest currently supported kernel version is 3.10).
Because builds here are really not stable, I'll just leave a disclaimer here.
Code:
#include <std/disclaimer.h>
/*
* I am not responsible for bricked devices, dead SD cards, thermonuclear
* war, or the current economic crisis caused by you following these
* directions. YOU are choosing to make these modificiations, and
* if you point your finger at me for messing up your device, I will
* laugh at you.
*/
Working features
RIL
Camera (front & rear) - only works in <3.8
Video (playback & recording)
Audio (playback & recording)
Wifi
Bluetooth (broken in >=3.8, needs a workaround to manually startup)
USB, ADB
Tethering (not tested)
GPS (not tested)
Sensors
Known bugs
IRQs are mishandled by some device drivers (abb_btemp, abb_fg)
proximity sensor might not work (not tested, cause it's broken on my device)
deep sleep might not work at a times
MMC driver works unreliably in >=3.8 (contiguous usage might lead in a data corruption)
networking is not fully-functional (no mobile data)*
camera is broken in 3.8
*some other features of the android kernel might not present - it's because these kernels lacks android-specific patches.
Sources
LK 3.5
LK 3.6
LK 3.7
LK 3.8
LK 3.9
LK 3.10
Downloads
http://xda.mister-freeze.eu/XDA-files/ChronoMonochrome/misc/upgrading
Installation
install chrono kernel r5.2 or higher (this is needed to pick up the necessary scripts, incl. bootscripts, etc)
reboot to recovery
install build linked in "Downloads" section
Credits
Linux kernel development community
Google
ST-Ericcson
Samsung
Team Canjica
XDA:DevDB Information
U8500 Linux kernel upgrading project, Kernel for the Samsung Galaxy Ace II
Contributors
ChronoMonochrome
Kernel Special Features:
Version Information
Status: Alpha
Created 2017-05-09
Last Updated 2017-05-10
Reserved
Porting
The porting a higher kernel version tehnique I'll describe here is not intended to be a guide for dummies. I'll assume you've already built a kernel for your device, familiar with git versioning control usage and with some porting / coding tehniques.
Firstly, you need a cleaned source for your device. By "cleaned" I mean, there are no Linux incremental patches, android changes applied, manufacture-specific patches are avoided when possible and so on - you need sources as closest to a "pure" Linux kernel as possible. Otherwise you'll have later need to deal with conflicts resolution, you'll most likely be unable to resolve and the kernel won't boot.
So, without a further forewords, the tehnique is below:
1) As was previously mentioned, a clean kernel source is required, I'll assume we are starting from LK-3.4 ( https://github.com/ChronoMonochrome/Chrono_Kernel-1/commits/ea228ee0f5e9935841aff25c62fa163cd78dc01d ) and porting a higher kernel versions. A kernel base needs to be tested for any bugs just to distinguish, which bugs were intruduced during porting from those ones that already present in a kernel base.
2) The following steps will mostly use git bisect and git merge commands in order to merge all the changes from a higher kernel versions and help to find / resolve the bugs that were introduced. I suggest copying a git kernel repo that you use for building to a somewhere else, so you can use it , e.g. for grepping a different versions source, bisecting the revisions and so on, so don't need to bother messing up in your main repo that you use for build.
3) Firstly, lets just try to merge a higher kernel version, e.g. LK 3.5 by issuing a command git merge lk-3.5. You'll likely have a lot of merge conflicts, most of which you can resolve with resetting the paths to a some revision (either a kernel base - lk 3.4, or the version you do port, or just another suitable conflict resolution). So I suggest to write those paths to a text file, like so:
Code:
arch/arm/boot
arch/arm/mach-ux500
arch/arm/plat-nomadik
drivers/mmc
include/linux/mmc
drivers/usb
include/linux/usb
drivers/mfd
include/linux/mfd
...
Write all the paths you intend to reset to the kernel base, you most likely need to re-use them later. To actually perform a resetting source, you can issue
Code:
for path in $(cat file_with_a_paths.txt | xargs)
do
git checkout COMMIT $path
done
Be sure not to put to this file anything not the device-specific! Resetting to the kernel base should be avoided when possible (never ever try resetting archictecture-specific paths, e.g. arch/arm/kernel, arch/arm/mm and so on - unless you really know that kernel will boot thereafter, instead, you have to manually resolve such conflicts). Resolve any other conflicts by resetting paths to the porting source (e.g. LK 3.5).
Note. While resetting with a paths is probably not the most accurate tehnique, but people don't live that long to use more accurate approach, e.g. performing git cherry-pick for every upstream commit and then manually resolving all the conflicts, you'll just sooner or later get bothered and will abandon it.
4) When you're done with the previous steps you can try building kernel. You'll likely have a build errors - because some part of a source got not updated (e.g. the device-specific drivers), you need manually implement the necessary by a higher kernel version changes. Firstly check if an upstream kernel contains the necessary fixes (example: https://github.com/ChronoMonochrome/Chrono_Kernel-1/commit/9fae8c449b710f502662da1cbcf26ece5a098af9 , https://github.com/ChronoMonochrome/Chrono_Kernel-1/commit/fe027c25d6db0d100937deb5248e249ec5b24ee7 ). If the driver you are porting doesn't exist in the upstream, you can also try to find a similar change and mimic it: https://github.com/ChronoMonochrome/Chrono_Kernel-1/commit/5f2e7afbf2ac3284dc62b3d96a0627c7f99ed4e9 ( ported similarly to https://github.com/ChronoMonochrome/Chrono_Kernel-1/commit/526c597 ). In the worst case scenario you will need to examine the upstream changes and apply the changes so that the drivers complies to the upstream changes: https://github.com/ChronoMonochrome/Chrono_Kernel-1/commit/ea6432d167 .
5) If everything is done properly and you're lucky enough, the compiled kernel might already bootup. If not, you'll need to find a culprint that doesn't let the device to boot up. Switch to a copy of your kernel sources, reset the source to the base kernel version (e.g. LK 3.4), issue git bisect good, then issue git bisect bad lk-3.5, git will reset to a somewhere in a middle between of LK 3.4 and LK 3.5.
6) Save your changes in the kernel repo, by assigning a some branch to it, switch to the source base, merge all the fixes you've already introduced, then merge the revision you have got in the previous step by bisecting the tree. Repeat these steps until you'll find a first bad commit.
7) If you are already on this step, the most trickiest part starts here - testing (hopefully) working kernel for bugs (if any). While logs can be useful sometimes (so you can google the failing messages and find something useful), there are also many bugs you can find only performing git bisect tehnique decribed above.
The decribed algorithm only possible thanks to having a clean kernel source. The usage of this guide is not limited only to the kernel porting, it can be used on other projects as well, this is just what I've come across to, when I've ever started porting Linux kernel versions higher than LK3.4.
Reserved
I wonder if any of this expertise couldn't look pretty cool here too.
Wooooowwwewe
Oooh
Look whose good boys have been trying to win the STE mastermind prize as of lately
https://github.com/novathor-mainline/linux
https://git.kernel.org/pub/scm/linu...inux-nomadik.git/log/?h=ux500-skomer-v5.5-rc1
mirhl said:
Oooh
Look whose good boys have been trying to win the STE mastermind prize as of lately
https://github.com/novathor-mainline/linux
https://git.kernel.org/pub/scm/linu...inux-nomadik.git/log/?h=ux500-skomer-v5.5-rc1
Click to expand...
Click to collapse
Seriously!
mirhl said:
Oooh
Look whose good boys have been trying to win the STE mastermind prize as of lately
https://github.com/novathor-mainline/linux
https://git.kernel.org/pub/scm/linu...inux-nomadik.git/log/?h=ux500-skomer-v5.5-rc1
Click to expand...
Click to collapse
Wow, that's incredible
Exynos4412 already got some mainline support, it would be very nice to have this one supported too.
Aaaaand it's done, kinda.
ST-Ericsson NovaThor U8500 - postmarketOS
wiki.postmarketos.org
device/testing/linux-postmarketos-stericsson · master · postmarketOS / pmaports · GitLab
postmarketOS package build recipes
gitlab.com
Project Treble for Xperia XZs
With this project, you can run (almost) any Generic System Image(GSI) on your Xperia XZs. This means you can test LineageOS, Havoc, Pixel Experience...
No repartitioning necessary! This method is re-using the oem partition.
What is Project Treble?
Understanding Project Treble and Android updates
Talkin’ Treble: How Android engineers are winning the war on fragmentation
What are GSIs?
Android Source: Generic System Image (GSI)
Downloads:
ROM: Download the latest aosp_f8331_*-TREBLE-NIGHTLY.zip from sx.ix5.org/files/builds/keyaki/aosp/
TWRP: Download twrp-kagura-oem-to-vendor.img Wait until a treble-compatible recovery is made
How to install:
Back up your stuff
Wipe data and caches
Install the zip via TWRP (or unzip and install just the /boot and /vendor images via fastboot)
Install any GSI via "fastboot flash system your-gsi-image.img"
To use Magisk: Flash twrp-kagura-oem-to-vendor.img as recovery. Reboot into recovery and install Magisk like you usually would. If you want to go back to another ROM, you need to re-flash your old TWRP recovery as well.
Bugs: See post #2
DO NOT POST HERE FOR FLASHING HELP OR YOU WILL BE REPORTED. Read everything before posting.
If you have questions, ask them in this thread: AOSP 9.0 Pie builds for F8331/F8332
List of GSIs: phhusson's treble Generic System Image
Important: You need an A-Only, ARM64 GSI!
GSIs based on phhusson's work offer the best compatibility.
Magisk: For Magisk to work, you need to tweak your TWRP installation, since it doesn't know that we have shuffled /vendor to the oem partition. You need to change /oem to /vendor in TWRP's fstab file.
See above for a tweaked TWRP.
If you want to go back to any other AOSP-based ROM that is not a GSI, simply re-flash the regular oem image and install like you usually would.
For developers:
This method is repurposing the oem partition to hold /vendor and odm(blobs). There's 400mb of space on that partition and we are only using ~260mb for blobs, while vendor is only about 20-30mb.
Re-partitioning can be quite dangerous if you do not know what you are doing. This method should be safe for everyone.
Sources are up now.
local_manifests
kernel (with patches)
sony's repo_update
ix5_repo_update: run ix5_repo_update.sh and then treble_repo_update.sh
You need to tweak the following:
Kernel dtsi to disable "odm" and load /vendor from "bootdevice/by-name/oem"
PlatformConfig on tone
device-sony-common:
adreno-symlinks branch
symlink from /vendor/odm/lib to /vendor/lib instead of from /odm/lib: Extra symlinks for build.prop and radio (aosp already symlinks /odm to /vendor/odm, but it omits build.prop and our radio folder)
Misc fixes
PRODUCT_FULL_TREBLE_OVERRIDE needs to be "true"
device-sony-tone: treble fixes:
Mount oem as /vendor in fstab
"TARGET_COPY_OUT_VENDOR := vendor" needs to be set
Set VNDK versions, and override properties that get set because the build system is made to believe our XZ shipped with Oreo
device/sony/odm with odm files
Unpack the oem blobs under device/sony/odm/odm and follow the README in device/sony/odm/README.
We need to put the odm files("blobs") somewhere. They get symlinked from /vendor/odm to /odm; both locations need to be accessible.
sepolicy: Use the broad-updates branch (it's kinda hack-ish now because /odm/pm-service is using /dev/binder, which messes with sepolicy). Sepolicy is on permissive for these builds because of that issue.
Tested:
AOSP Extended (calling works, bluetooth may crash)
Havoc (no calling, bluetooth may crash)
Camera should work everywhere
Bugs are the same as the regular AOSP builds, plus some more if the GSI is not built well or doesn't have tweaks for Sony devices.
Happy holidays, I hope you have fun with this!
XDA:DevDB Information
Project Treble for Xperia XZ F8331/2, ROM for the Sony Xperia XZ
Contributors
local__hero
ROM OS Version: 9.x Pie
ROM Kernel: Linux 4.x
ROM Firmware Required: .184 or later stock firmware
Based On: AOSP
Version Information
Status: Nightly
Created 2018-12-30
Last Updated 2018-12-30
XDA:DevDB Information
Project Treble for Xperia XZs [Pie 9.0], ROM for the Sony Xperia XZs
Contributors
local__hero
Source Code: https://git.ix5.org/felix/local-manifests-ix5
ROM OS Version: 9.x Pie
ROM Kernel: Linux 4.x
ROM Firmware Required: Stock Oreo firmware, best .184
Based On: AOSP
Version Information
Status: Nightly
Created 2019-01-28
Last Updated 2019-06-10
Reserved
Reserved
Gb321 single card installation error
Man, can you explain the installation better? I don't understand how it installs on the vendor, boot and twrp (I'm Brazilian, I'm sorry for my bad English)
There's three vendors and none of them is image how can I flash them
Thread closed at op's request.
Thank you for your contributions :highfive:
strongst
Forum Moderator
Arch Linux is an independently developed, x86-64 general-purpose GNU/Linux distribution that strives to provide the latest stable versions of most software by following a rolling-release model. The default installation is a minimal base system, configured by the user to only add what is purposely required.¹
NOTE: The Arch Linux packages are no longer updated. Consider taking a look at the postmarketOS port instead.
Introduction
With Android 5.0 (Lollipop), the ASUS MeMO Pad 7 (ME176C(X)) was updated with UEFI boot, making it possible to boot any Linux distribution on it. archlinux-me176c aims to make Arch Linux fully work on the ASUS MeMO Pad 7 (ME176C(X)). It provides additional packages and documentation for using Arch Linux on this device.
With me176c-boot, Linux can be installed in dual/multi boot configurations together with Android. Arch Linux is a minimal distribution, therefore most of the setup (partitioning, installing a desktop environment, ...) will be left up to you. However, it also allows you to customize it entirely to your liking, and configure it for any use case you can imagine.
Installation
Warning: Although the wiki article below provides many recommendations, at the end, setting up the installation will be left up to you. There is no step-by-step guide. If you have never used Arch Linux before, you may want to try it on a desktop PC or virtual machine first. You can easily brick your tablet if you don't know what you are doing!
All documentation is available in ASUS MeMO Pad 7 (ME176C(X)) - ArchWiki. As a wiki article, I encourage everyone to contribute and share their experiences with everyone else.
If you need any help or further suggestions, do not hesitate to ask in this thread!
FAQ
Can I use other Linux distributions on this tablet? Yes! However, you will need to set up more things manually. There are a few notes for this in linux-me176c: Porting - Using linux-me176c in other distributions
Source Code
Documentation: ArchWiki
Packages: archlinux-me176c (GitHub)
¹ Source: https://wiki.archlinux.org/index.php/Arch_Linux (GFDL 1.3)
XDA:DevDB Information
Arch Linux for ASUS MeMO Pad 7 (ME176C(X)), Tool/Utility for the Asus MeMO Pad 7
Contributors
lambdadroid
Source Code: https://github.com/me176c-dev/archlinux-me176c
Version Information
Status: No Longer Updated
Created 2019-04-02
Last Updated 2020-05-12
Reserved
Hi!
Seem awesome!
Do this have a full hardware accelerated graphics support?
Is this compatible with k013 ?
shim80 said:
Do this have a full hardware accelerated graphics support?
Click to expand...
Click to collapse
Yes. (It has Intel Graphics just like on normal Intel PCs, and therefore OpenGL and Vulkan support is provided by Mesa.)
shim80 said:
Is this compatible with k013 ?
Click to expand...
Click to collapse
Yes, K013 == ME176C(X).
Thanks for the answers.
Also, if wan't to go back to Android, can I do it?
shim80 said:
Also, if wan't to go back to Android, can I do it?
Click to expand...
Click to collapse
The recommended setup is to keep Arch Linux on an external SD card. Then you can have Android and Arch Linux installed at the same time ("dual boot").
@lambdadroid man when running
# pacman -Sy me176c
or trying to install base packages it says
error: me176c:signature from "lambdadroid is known trust error: failed to update me176c (invalid or corrupted database (GPG signature)
when running
$ pacman-key --finger keyid
it says pub
ed25519 2017-08-10 [sc] [expired: 2019-08-17] uid [expired]
should I try an offline instalation?
No longer updated
The binary repository has been down for a while now - I have no plans to update the Arch Linux packages again. This is mostly because I'm no longer using Arch Linux myself on the me176c / K013.
However, as a replacement a postmarketOS port with same functionality has been around for a while. Since it's much more comfortable to install (simply through Fastboot/SD card with a large number of selectable UI interfaces) I prefer it over Arch Linux at this point. I would recommend it to anyone who would like to use a more standard "Linux" distribution on me176c / K013.
Kirisakura-Kernel for the Asus Zenfone 9
Hello everyone,
To keep it short: Here is Kirisakura - Kernel for the Asus Zenfone 9 aka DaVinci. The Zenfone line-up internal codenames were traditionally derived from alcoholic drinks. Two years ago the Zenfone 6 bore the title "Kirin". The Zenfone 7 was codenamed "Tequila", while the Zenfone 8 bore the title "Sake".
This year seems to make a change however. The Zenfone 9´s internal codename is "DaVinci".
I would appreciate if everybody that flashes the kernel, reads at least once through this opening post and the following ones.
As far as we, @tbalden and me, are aware and as far as we know this project, alongside CleanSlate kernel for the Zenfone 9, marks the first release of a source compiled custom QGKI 2.0 kernel as a standalone flashable zip and project here on XDA.
The introduction of GKI and QCOMs adaptation QGKI means unfortunately that building a monolithic kernel becomes harder and harder. This results in the "kernel" itself no longer just sitting in one partition or the zImage, but it´s spread across different partitions (no longer being monolithic) now. Since there´s no requirment to keep monolithic builds working as in the past, it´s no longer possible to compile the source as is (without applying major rewrites, tricks or hacks) in the monolithic fashion on 5.10 kernels. The same was true for the Pixel 6/Pro.
That means the "kernel" project you´re seeing here needs to be compiled in a build environment to achieve the GKI/QGKI way. Since only Google releases the full build environment alongside the kernel sources itself in a proper fashion with git history, it became very complicated and seemingly impossible to do this on the Zenfone 9 at first glance. A big thanks at this place to Asus. From all the sources of SD8 Gen 1 QGKI devices published, the Asus Source is the most complete. A big thanks to Asus for publishing the sources on time and complete! Also for listening to us if the source is not complete and something is missing.
With excellent teamwork and a lot of hardwork, @tbalden and me managed to compile the Zenfone 9 kernel in QGKI 2.0 fashion after a lot of failed attempts and misery. It´s been a pleasure to work with him over the years here on XDA.
Kirisakura - Kernel is designed to bring a handful of beneficial features to the device, while ensuring excellent performance and smoothness to get you safely through the day!
If you expect a custom kernel to magically improve your devices battery life manifold and this is your only priority then this might not be the right place for you.
However the kernel is built to keep battery life close to the same as you would experience the on stock kernel while being tuned to perform better in various UI related benchmarks. The same benches are used by google to verify and ensure UI smoothness on the Pixel devices. The scheduler is tuned to yield lower jitter and reduce jank frames.
If that got your curious, I welcome you to continue reading if you´re still interested!
This project aims to keep most of the subsystems updated, way ahead of the stock kernel, thereby improving security and performance, while keeping stability as the foucs during testing! This includes Linux-Stable, CAF-Upstream and kernel/common.
A very positive development. Google pushed for CFI and SCS to be enabled by default in the android-common kernel. Starting with 5.4 kernel ( SD 888 ) CFI and SCS were enabled by default. It was a lot of work to get these features working nicely on the kernel I did the years back. So it´s nice to see this is now there by default in everybody can profit from it.
I put the explanations and links in hide tags here.
Spoiler: Documentation Control-Flow-Integrity (CFI) / Shadow Call Stacj (SCS)
Kernel Control Flow Integrity (Kernel-CFI), which is achieved by linking the kernel with LLD and Link Time Optimization (LTO), more precisely ThinLTO, are quite unique security features.
The recently released Kirisakura-Kernel for the OnePlus 8 Pro was featured on the XDA-Portal due to the inclusion of CFI. The featured article explains CFI in great details, is easy to understand and definitely worth to read.
If possible the latest Kirisakura-Kernel releases for various devices aim to include CFI in enforcing mode so users can benefit from this security features.
Another security feature is Shadow Call Stack (SCS).
SCS is another security patchset that is aimed at preventing attacks via return oriented programming (ROP).
ROP is a technique where the attacker gains control of the kernel stack to overwrite function return addresses and redirect execution to carefully selected parts of existing kernel code.
If you´re interested here are a few good links:
Google Security Blog explaining SCS.
LLVM doc about SCS
Android DOCs documenting SCS
If reading about upstream in the paragraph above got you curious, have a read about Linux-Stable and why it is important here. The stable-process is not the same for every subsystem, but the general idea, rule of thumb and benefits are applicable for other subsystems as well.
Read more about the Release-Model following this link.
This conversation on the LKML mailing list also shows the power of Linux-Stable and why it´s very beneficial to not just say it´s not worth and a potentiol source for bugs:
Starting with the Initial Message , the following reply and a good summarizing statement.
Quick explanation of QCOM-Upstream. CLO-git is the place where development from Qualcomm for their SoCs happens. This includes the Snapdragon 8+ Gen1 that´s built into the different SKUs of the Zenfone 9.
The kernel-bases available on QCOMs git, are basically the foundations OEMs use, to build their own kernel additions on top for devices featuring Qualcomm SoCs.
The Qualcomm developers push regular updates to the bases of the different SoCs, a bit similar to how Linux-Upstream works. OEMs usually stop updating the initial base after the phone is released.
This kernel focuses amongst the other features to provide the latest CAF-Updates merged in a regular manner, to provide updates, improvements and enhancements for SoC specific drivers and subsystems! This might take a while, because a lot of device specific testing is done on my end to ensure stability.
The kernel includes a lot of improvements and contributions from other developers as well. Without this kernel would not exist.
A big part of improvements originate from @arter97´s, @kdrag0n´s and @Sultanxda´s work. Many others contributed in some way or another to this kernel.
A big thanks to all of them at this place!
Now lets continue with a list of features in the next paragraph!
Main Features:
- Based on latest kernel sources from Asus for Android 13 and intended to be used on the latest Asus Stock-Firmware
- compiled with Clang 16.0.2 and built with -O3 speed optimizations
- Linux-Stable-Upstream included to 5.10.181
- upstreamed QCOM base for the Snapdragon SD8+ Gen1 (qcoms internal codename "cape")
- Lazy RCU which should result in power-savings while the device is lightly-loaded or idling, more information here
- include important fixes/improvements from kernel/common
- SSG IO scheduler for reduced overhead and less CPU cycles (more lightweight and android optimized)
- implement ramoops for easier logs in case of kernel panics
- implement LRNG (see arter kernel OP for more info )
- Flashing the kernel will keep root!
- Flashable via EXKM, FKM or Kernel Flasher (free open source solution, get it here)
- Anykernel zip is based on the Anykernel3 release from @osm0sis
EAS related features:
- Implement dynamic WALT-Window size depending on current FPS, collecting information about CPU-Load to provide more precise information for the scheduler
- EAS implementation patched up to latest CAF state
- updates from kernel/common
CPU related features:
- Power saving workingqueues enabled by default
- Change various drivers (WLAN, MM, audio, charger, power, thermal, glink etc) to use power efficient workingqueues. This compliments EAS in general
- vdso32 patches as found on Google Pixel devices (brief documentation here) (CAF 5.10 default, keep for documentation)
- improve suspend/resume from audio driver (caf-upstream for audio-kernel)
- enable suspend_skip_sync to save power during suspend/resume
- speed up face unlock
- reduce camera launch time
GPU related features:
- GPU driver updated to latest CAF-State
File System related features:
- f2fs improvements
UI/UX/Usability related features from CleanSlate:
- CleanSlate features made by @tbalden
- Disclaimer: All CleanSlate features can be controlled via the free companion and config app found on CleanSlate thread here on the Zenfone 9 Forums on XDA. Please consider buying the premium versions if you enjoy using the CleanSlate features, to give a little something back to @tbalden.
- add option to force 240hz touch sample rate
Network related features:
- Wireguard Support (Details)
- advanced TCP algorithms enabled
- use bbr as default TCP congestion algorithm (fasted algo according to this excellent research from @kdrag0n found here )
- includes new bbr
- Enable support for TTL spoofing
Memory related features:
- Speculative Page Faults left enabled (1. 2) (CAF 5.4 default, keep for documentation)
Security related features:
- Control-Flow-Integration (CFI) and Link-Time-Optimization (LTO) (CAF 5.4 default, keep for documentation)
- Use ThinLTO which was first used in the Pixel 4 XL Android R-Kernel instead of full LTO (CAF 5.4 default, keep for documentation)
- Shadow Call Stack (SCS) Security-Feature ( 5.4 default, keep for documentation)
- enable init_on_alloc for even more security, more information can be found in the commit message (CAF 5.4 default, keep for documentation)
Other features:
- clean up asus drivers and fix a few warnings in kernel log
- enlarge dmesg size to ease debugging
Flashing Guide, Download and Changelog
Requirements:
- unlocked Bootloader (this will void warranty and kill future OTA updates on all asus phones at the moment)
- USB-Debugging in developer options enabled
- latest adb and fastboot binaries
- working adb and fastboot environment
- magisk root
- a backup of stock boot.img, vendor_boot.img, vendor_dlkm.img and dtbo.img so you can go back to stock conditions (simplest way is TWRP or to extract from stock firmware via payload extractor)
How to flash the Kernel:
1. Download the latest kernel.zip and make sure you have properly updated to the latest matching Asus Stock-Firmware. When the Zenfone 9 receives an OTA update it takes Asus a while to release the source code for the new OS and me a while to build a new kernel. If you don´t want to face any issues, wait until I either release an updated kernel or give green light because there were no kernel changes.
Always make sure to run the firmware the kernel is built for!
If you feel adventurous and try in advance, make sure you have a backup ready!
2. Flash the kernel.zip in your favorite kernel app (I personally use Kernel Flasher by @capntrips as it´s free OSS) or TWRP once available.
3. Reboot and profit.
DOWNLOAD:
Download is located always in this folder:
AFH is currently down. Please check release posts for attached files.
https://www.androidfilehost.com/?w=files&flid=335947
Important: Read after Download
Please take a look at the second post after flashing the kernel!
Changelog:
Android 12
1.0.0 Initial Release
1.1.0 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-87544785
1.1.0 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-87641829
1.1.3 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-87761015
Android 13
2.0.0
[Kernel][09.12.2022][Android 13] Kirisakura 2.0.0_T for Asus Zenfone 9 aka "DaVinci"
Kirisakura-Kernel for the Asus Zenfone 9 Hello everyone, To keep it short: Here is Kirisakura - Kernel for the Asus Zenfone 9 aka DaVinci. The Zenfone line-up internal codenames were traditionally derived from alcoholic drinks. Two years ago...
forum.xda-developers.com
2.0.6 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-87945357
2.0.12 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-88194923
2.0.18 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-88332217
2.0.19 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-88360955
2.0.21 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-88384057
2.0.24 https://forum.xda-developers.com/t/...s-zenfone-9-aka-davinci.4489055/post-88600875
Donations:
Donations are not mandatory but very welcome if you want to support development or just buy me a coffee/tea
If you like my work: http://paypal.me/freak07
Credits:
Asus for the development device, giving me the opportunity to create this project! This device is absolutely stunning!
@osm0sis for all his work, including the ak3 installer!
@capntrips for his relentless work on several projects, including kernel flasher!
@tbalden for being the best HTC, Pixel, OnePlus and now Asus wingman!
@LeeDroid and @mwilky for their awesome roms and work I used on multiple devices!
@Captain_Throwback for all the mentoring and guidance!
@Eliminater74 for bringing me into the game and the Inspiration
@nathanchance for his upstream guidance and assistance
@RenderBroken for helping me out
@flar2 for all his work
@joshuous for all the help he provided to me in the past!
@arter97 for giving me advice
@kdrag0n for his help and advices!
@topjohnwu for magisk!
Source Code: https://github.com/freak07/Kirisakura_DaVinci_AI2202/
For necessary changes to other repos, besides the main kernel tree please check tbaldens github, we did the bringup together:
tbalden - Repositories
engineer. Started github with kernel for HTCDoubleshot, migrating version in 2011. kernel follows kernel, patching intuitive new features into CleanSlate line. - tbalden
github.com
F.A.Q:
Question: How do I return back to stock?
Answer: Extract boot.img, dtbo.img, vendor_boot.img and vendor_dlkm.img from the matching factory image provided on googles download page.
If you want to stay rooted make sure to flash a boot.img that has been patched with magisk.
Flash those images via fastboot/fastbootd and you will be back on stock kernel.
boot.img, dtbo.img and vendor_boot.img are to be flashed in regular fastboot.
vendor_dlkm.img is to be flashed in fastbootd (you can get to this with "fastboot reboot fastboot" when you´re in regular fastboot)
Question: How to report bugs properly?
Answer: Have a look at post #3 in the linked thread. The linked guide is a pretty good starting point.
Before reporting any bug make sure you´re running on a stock configuration. That´s means you´re not using any mods, tweaks in kernel managers or other root tweaks , magisk modules, scripts or other modifications that alter various functions like sound mods, data traffic, sleeping behaviour, scheduler, magical battery tweaks etc.
Try to describe the issue as detailed as possible! Give your exact setup, like rom, magisk version, kernel version.
Is the issue reproducible? Does it happen frequently?
Please make sure to meet the points described above, provide logs as detailed in the link above, otherwise debugging is a lot more time consuming and harder. If these requirements aren´t met and I don´t find time to either reproduce the issue myself or I´m not able to reproduce the issue myself reports might just be ignored. If you can already reproduce the issue and provide logs it greatly limits the amount of time I have to spent until I figure out how to reproduce it.
Question: What about unlocking, rooting, passing safetynet, apps detecting root/modifications and other topics that are vaguely related, but not really subject of this thread?
Answer: If you want to modify your phone via root/magisk in any way you need to unlock the bootloader. Unlocking will result in safetynet not passing. This has nothing to do with the kernel. At the moment of writing this, safetynet not passing can be worked around with a magisk module called "Universal SafetyNet Fix".
Not passing safetynet is unrelated to the kernel since hardware attestation is enforced on nearly all newly released devices now.
If you´re not passing safetynet banking apps might for example be detecting root. There are various tricks to hide root/modifications to the phone from banking apps or others but that´s not really subject of this thread.
taken from pixel 6 soon to be adjusted
AOSP Build Environment and Standalone Kernel builds (monolithic builds)
I´m sure some of you followed the movement towards the Generic Kernel Image (GKI) and Qcoms adaption to it called QGKI.
You can find more information about GKI following this link.
What does that mean for custom kernels and this custom kernel?
The last few years the kernel on android devices was more or less compiled as a monolith. That means the kernel is in the zImage with all (most) drivers compiled inline.
However with GKI this changed. There´s the base kernel image while vendor/device specific drivers are compiled as dynamically loadable kernel modules.
On last years devices like the Pixel 5 (using a 4.19 kernel) and this years devices with SD888 on a 5.4 kernel base, there was the possibility to change the QGKI kernel back into a monolithic kernel image. (building the drivers that are on stock kernel external modules back into the zImage to end with a monolithic kernel)
On the Pixel 6 I wasn´t able to achieve this yet. But during my tries I also wondered if maybe finally the time has come to follow suit, instead of trying to enforce old ways, when there´s a new way going forward.
What does that mean. This means that at this point the kernel is shipped as images that are to be flashed via fastboot. At a later stage I´m sure we can modify anykernel3 to allow flashing zips again, but at this early stage fastboot flashable images will be provided.
Those images can be flashed the same way the device is rooted, therefore I think everybody should be able to flash it easily since the device can´t be rooted any other way.
The kernel was compiled using the aosp kernel build environment. Information about it can be found on the documentation page from google.
this one too
and this one as well
Woohoo! Rock'n'roll! ^__^
Update to 1.1.0
Hey guys and girls,
Here´s the next update. It includes quite a few changes.
It also includes the few kernel changes from the latest firmware 32.2040.2040.23.
The link to the latest firmware can be found following this link.
More changes in the changelog below:
Changelog:
- Linux-Stable upstream bumped to 5.10.146
- merge latest CAF-Upstream
- bump clang to prebuilt 14.0.7 from google
- fixed clang warnings in the process
- other improvements and tweaks please check github
Download:
AFH is currently not working properly. Please check this post for the download. Kernel.zip is attached.
https://www.androidfilehost.com/?w=files&flid=335947
Instructions can be found in the OP!
But look at this post too
Have fun, enjoy the kernel and your phone.
Donations are not mandatory but very welcome.
If you like my work and want to buy me a coffee/green tea to keep development going: http://paypal.me/freak07
Freak07 said:
Update to 1.1.0
Hey guys and girls,
Here´s the next update. It includes quite a few changes.
It also includes the few kernel changes from the latest firmware 32.2040.2040.23.
The link to the latest firmware can be found following this link.
More changes in the changelog below:
Changelog:
- Linux-Stable upstream bumped to 5.10.146
- merge latest CAF-Upstream
- bump clang to prebuilt 14.0.7 from google
- fixed clang warnings in the process
- other improvements and tweaks please check github
Download:
AFH is currently not working properly. Please check this post for the download. Kernel.zip is attached.
https://www.androidfilehost.com/?w=files&flid=335947
Instructions can be found in the OP!
But look at this post too
Have fun, enjoy the kernel and your phone.
Donations are not mandatory but very welcome.
If you like my work and want to buy me a coffee/green tea to keep development going: http://paypal.me/freak07
Click to expand...
Click to collapse
Hello sir,
How do you compile the original Kernel? Is any of vendor_boot or vendor_dlkm images the same as original stock or both are different? What about DTBO? I'm trying to build kernel for ROG Phone 6 but I thought kernal was still a monolithic file, so I flashed one only and failed to boot. ROG Phone 6 includes a script that apparently compiles everything but I don't which one is DTBO, vendor boot and vendor dlkm. Where and how you compile this kernel and where does the output go? For example I see kernel-platform/msm-kernel as the one you modified? That one is the vendor_boot?
Thank you for your help
And by the way, any plan for Kirisakura for ROG Phone 6?
Update to 1.1.1
Hey guys and girls,
Here´s the next update. It includes quite a few changes.
It also includes the few kernel changes from the latest firmware 32.2050.2050.29.
The link to the latest firmware can be found following this link.
More changes in the changelog below:
Changelog:
- included few changes from firmware 32.2050.2050.29
- other improvements and tweaks please check github
Download:
https://www.androidfilehost.com/?w=files&flid=335947
Instructions can be found in the OP!
But look at this post too
Have fun, enjoy the kernel and your phone.
Donations are not mandatory but very welcome.
If you like my work and want to buy me a coffee/green tea to keep development going: http://paypal.me/freak07
Lossani said:
Hello sir,
How do you compile the original Kernel? Is any of vendor_boot or vendor_dlkm images the same as original stock or both are different? What about DTBO? I'm trying to build kernel for ROG Phone 6 but I thought kernal was still a monolithic file, so I flashed one only and failed to boot. ROG Phone 6 includes a script that apparently compiles everything but I don't which one is DTBO, vendor boot and vendor dlkm. Where and how you compile this kernel and where does the output go? For example I see kernel-platform/msm-kernel as the one you modified? That one is the vendor_boot?
Thank you for your help
And by the way, any plan for Kirisakura for ROG Phone 6?
Click to expand...
Click to collapse
boot.img contains the zImage, vendor_boot contains first stage kernel modules, vendor_dlkm contains second stage kernel modules.
Kernel is no longer monolithic by default. I´m using the build environment to get the relevant images for GKI.
Freak07 said:
boot.img contains the zImage, vendor_boot contains first stage kernel modules, vendor_dlkm contains second stage kernel modules.
Kernel is no longer monolithic by default. I´m using the build environment to get the relevant images for GKI.
Click to expand...
Click to collapse
Do you have any kind of tutorial to follow to pack the kernel like you do in AnyKernel zip?
Thank you
Lossani said:
Do you have any kind of tutorial to follow to pack the kernel like you do in AnyKernel zip?
Thank you
Click to expand...
Click to collapse
I´m sorry but a step by step tutorial I don´t have the time to type that all down.
Please check tbaldens github for ZF9. We did the "bringup" of the ZF9 GKI environment together.
That here contains the scripts/methods we basically use both.
GitHub - tbalden/android_kernel_asus_zf9_build_env
Contribute to tbalden/android_kernel_asus_zf9_build_env development by creating an account on GitHub.
github.com
Check all the other zf9 repos as well.
We took basically the asus build script inside the ROG 6 source, readjusted it for the ZF9 source, as the build environment for the ROG 6 was more complete than ZF9.
You either need to remove avb from fstab (that lands in vendor_boot) or disable vbmeta flags for verity/verfication before you can flash any modified vendor_dlkm.
Be aware, disabling the flags triggers an inevitable wipe.
Otherwise check the scripts and work yourself through all the repos.
Unfortunately with GKI kernels you need to adjust the ABI. Now it gets complicated. The gki kernel, the zImage is usually compiled, from the common repo, while the qcom specific drivers are built in the msm repo. Since I don´t care about preserving googles abi for the GKI kernel, I compile the zImage from the updated msm repo, as well as the qcom modules.
That means in my build environment common repo is a symlink of msm repo, while I compile with the same script found in ROG 6 source. I think once you start working through the build environment you´ll understand. Tbalden doesn´t need to do that, as his kernel is close to stock with only a few mild changes, so easier to keep abi in check.
Unfortunately at the moment there´s no easy way to compile it.
Freak07 said:
I´m sorry but a step by step tutorial I don´t have the time to type that all down.
Please check tbaldens github for ZF9. We did the "bringup" of the ZF9 GKI environment together.
That here contains the scripts we basically use both.
GitHub - tbalden/android_kernel_asus_zf9_build_env
Contribute to tbalden/android_kernel_asus_zf9_build_env development by creating an account on GitHub.
github.com
Check all the other zf9 repos as well.
We took basically the asus build script inside the ROG 6 source, readjusted it for the ZF9 source, as the build environment for the ROG 6 was more complete than ZF9.
You either need to remove avb from fstab (that lands in vendor_boot) or disable vbmeta flags for verity/verfication before you can modify vendor_dlkm.
Otherwise check the scripts and work yourself through all the repos.
Unfortunately with GKI kernels you need to adjust the ABI. Now it gets complicated. The gki kernel, the zImage is usually compiled, from the common repo, while the qcom specific drivers are built in the msm repo. Since I don´t care about preserving googles abi for the GKI kernel, I compile the zImage from the updated msm repo, as well as the qcom modules.
That means in my build environment common repo is a symlink of msm repo, while I compile with the same script found in ROG 6 source. I think once you start working through the build environment you´ll understand. Tbalden doesn´t need to do that, as his kernel is close to stock with only a few mild changes, so easier to keep abi in check.
Unfortunately at the moment there´s no easy way to compile it.
Click to expand...
Click to collapse
Thank you for your reply. I succeded to compile using ROG 6 script but I end up with a vendor_dlkm.img in out/target/platform/taro and in gki folder "dist" outputs Image, vendor_boot.img and another vendor_dlkm.img + dtbo.img but doesn't seem to be the correct size, I guess there's another step missing to compile or I don't know which one of the dlkm is the correct one or if I need another step to make the Image file and vendor_boot.img.
Thank you anyways
Lossani said:
Thank you for your reply. I succeded to compile using ROG 6 script but I end up with a vendor_dlkm.img in out/target/platform/taro and in gki folder "dist" outputs Image, vendor_boot.img and another vendor_dlkm.img + dtbo.img but doesn't seem to be the correct size, I guess there's another step missing to compile or I don't know which one of the dlkm is the correct one or if I need another step to make the Image file and vendor_boot.img.
Thank you anyways
Click to expand...
Click to collapse
check the scripts I just sent you. the vendor_dlkm and vendor_boot from the environment don´t work on the device.
The thing is, asus just uses the kernel environment to precompile zImage,all the modules, dtb and dtbo, then transfer those to their complete build environment and those get includes into the images that end up in the firmware. The zImage they´re using on the device is actually not the one compiled in the build environment, but the GKI kernel uploaded by google. That´s why abi is so important. You´re not supposed to flash the ones produced by the build environment.
Check the scripts how repacking both of those works. If everything is right, that will get you to boot.
the zImage you can get from ASUS_AI2202-32.2030.2030.26-kernel-src/kernel_platform/out/msm-waipio-waipio-gki/dist
Update to 1.1.3
Hey guys and girls,
Here´s the next update. Linux-Stable up to 5.10.149, which also fixed the CVEs discussed here and here.
The link to the latest firmware can be found following this link.
More changes in the changelog below:
Changelog:
- included few changes from firmware 32.2050.2050.34
- merge latest kernel/common
- linux-stable to 5.10.149
- includes a few fixed CVEs
- other improvements and tweaks please check github
Download:
Attached to release post, AFH is currently broken
https://www.androidfilehost.com/?w=files&flid=335947
Instructions can be found in the OP!
But look at this post too
Have fun, enjoy the kernel and your phone.
Donations are not mandatory but very welcome.
If you like my work and want to buy me a coffee/green tea to keep development going: http://paypal.me/freak07
Update to 2.0.0
Hey guys and girls,
Here´s the next update with source for A13 stable merged. (not much changes, hence the fast release)
Update to A13 stable before flashing this.
The link to the latest firmware can be found following this link.
More changes in the changelog below:
Changelog:
- included few changes from firmware 33.0804.2060.65
- merge latest kernel/common
- linux-stable to 5.10.157
- other improvements and tweaks please check github
Download:
Attached to release post, AFH is currently broken
https://www.androidfilehost.com/?w=files&flid=335947
Instructions can be found in the OP!
But look at this post too
Have fun, enjoy the kernel and your phone.
Donations are not mandatory but very welcome.
If you like my work and want to buy me a coffee/green tea to keep development going: http://paypal.me/freak07
Update to 2.0.6
Hey guys and girls,
Here´s the next update. That´s a bigger one. I´ll explain a few things below in more detail.
The link to the latest firmware can be found following this link.
Monolithic kernel build
Thanks to @arter97 it´s now possible to build the 5.10 qcom kernel now as a monolithic kernel, not needing to build as a GKI style kernel.
To explain it simple: The problem is QCOM/Google are no longer required to test if drivers are loading in the correct order and or test compilation of a monolithic kernel at all.
The gki style kernel has 100s of drivers build as external kernel modules, instead of directly into the zImage.
Having a monolithic build eases development a bit, but won´t directly make an impact to the user.
If you´re interested check my github, it contains the commits. and be sure to drop @arter97 a few thanks somewhere!
Introduction of Lazy RCU
Usually I´m not stating remarks about a change improving battery life notably. But this is one of the few kernel changes that really does make a noticeable difference.
This kernel has the entire(!) RCU subsystem updated to latest linux 6.0 kernel state. This also allowed for Lazy RCU to be merged into the kernel, which should result in power-savings while the device is lightly-loaded or idling (which is basically the case all the time a smartphone isn´t being interacted with (nothing touching the screen and no other workload such as video editing is done).
If you´re interested in details check the slides, which are also linked in the article mentioned/linked above.
A very simplified explanation: RCU functionality can be called 1000s of times a second, batching RCU calls can save power by not calling as often.
Please keep in mind, those are kernel changes and battery life will not be improved magically by huge amounts, but there´s definitely an improvments.
Sony Scheduler Improvements
Import some scheduler changes around Walt from Sony Xperia 1 IV. This improves jitter by a significant amount.
More changes in the changelog below:
Changelog:
- merge latest kernel/common lts branch
- linux-stable to 5.10.160
- merge latest qcom upstream to main branch
- bump clang to latest prebuilt from google 16.0.2
- lazy rcu backported
- scheduler improvements from Sony Xperia 1 IV
- remove wlan rx wakelock as it´s unnecssary
- other improvements and tweaks please check github
Download:
Attached to release post, AFH is currently broken
https://www.androidfilehost.com/?w=files&flid=335947
Instructions can be found in the OP!
But look at this post too
Have fun, enjoy the kernel and your phone.
Donations are not mandatory but very welcome.
If you like my work and want to buy me a coffee/green tea to keep development going: http://paypal.me/freak07
is there any possibility you could try to make such a kernel for rog 6 ? if you had a tester
luki2411 said:
is there any possibility you could try to make such a kernel for rog 6 ? if you had a tester
Click to expand...
Click to collapse
hi everybody. this is a very voluminous work, but still, if you decide, I am ready to take an active part in testing.
Hi Freak Will you port this kernel to ROG Phone 6 ?