Another update(1.3.8a) available here.
1.3.8a update
I can see the update too, but when I go to install, the message to proceed is in Chinese. I'm a bit nervous installing the update since I am on English and I'm worried I'll be getting a Chinese update!
areynoldsnz said:
I can see the update too, but when I go to install, the message to proceed is in Chinese. I'm a bit nervous installing the update since I am on English and I'm worried I'll be getting a Chinese update!
Click to expand...
Click to collapse
Went ahead anyway and it was fine.
Hi everyone, i have 1.3.6d pacefied FW, how i can install a clean non pacefied version? thx in advice
areynoldsnz said:
Went ahead anyway and it was fine.
Click to expand...
Click to collapse
any notable improvement?
rgonzm said:
Hi everyone, i have 1.3.6d pacefied FW, how i can install a clean non pacefied version? thx in advice
Click to expand...
Click to collapse
If your watch is a Chinese model (A1602) then you can update to rel.39 (1.2.51) and it should prompt you to install stock 2.6.0.12 (WOS2). ** Caution: don't try to install rel.39 directly, it may brick your watch).
If you have an international model (A1612) then you can try this (I haven't tested it tho):
https://forum.xda-developers.com/smartwatch/amazfit/fw-tool-stock-firmware-installers-2017-t3725494
I just got the update 1.3.8. I'm updating it now via the notfication on the watch. Hope everything works fine
Upgraded but yet again wiped my heart rate and sleep data off my watch. Last update did that as well.
Everything seems to be working though
So has anyone seen a changelog for this update?
Strange?? Update doesn't show for me but my brother already updated his Pace. We have the A1612/International model on official 1.3.7 FW.
macmel said:
Strange?? Update doesn't show for me but my brother already updated his Pace. We have the A1612/International model on official 1.3.7 FW.
Click to expand...
Click to collapse
I got the same bahaviour, no update available for my A1612 but one of my fried got it ...
It must be going out in stages, i have still not received the update on my watch either. I am still on 1.3.7, model 1612.
lfom said:
If your watch is a Chinese model (A1602) then you can update to rel.39 (1.2.51) and it should prompt you to install stock 2.6.0.12 (WOS2). ** Caution: don't try to install rel.39 directly, it may brick your watch).
If you have an international model (A1612) then you can try this (I haven't tested it tho):
https://forum.xda-developers.com/smartwatch/amazfit/fw-tool-stock-firmware-installers-2017-t3725494
Click to expand...
Click to collapse
Thx so much for your reply, i'll try later and post my results.
Update 1.3.8a
After updated the watch didnt Sync the charge informartion with the app
Anybody has This problem too?
Update 1.3.8a
I received this update last night and after updating it, I am not receiving any notifications and I don't have any stats regarding charging, ie. after I unplug the watch from my charger, is says "not being charged".
updated right now. Im getting the "Activity data sync failed (Code HO2)" just as with the previous update. This is getting a bit ridiculous.
edit: yes unpairing and repairing fixes it, at the cost of your daily activity. just as with 1.3.7
Got it as well with the same behavior as 1.3.7
Sent from my SM-G955F using Tapatalk
orenfl said:
Got it as well with the same behavior as 1.3.7
Click to expand...
Click to collapse
+1.
Just received
lfsouza said:
After updated the watch didnt Sync the charge informartion with the app
Anybody has This problem too?
Click to expand...
Click to collapse
I had this same problem. You must reset your watch to the factory settings. Next charge your watch battery to full.
Wysłane z mojego Nexus 5X przy użyciu Tapatalka
Related
I bought my phone on dec 4th and until that time I didn't receive any updates for my phone.
I have the European PLK-L01432B121 Firmware but the only option for me is to update my phone manually which is kinda annoying.
Does anyone else experience this problem?
I didn't find anything related to my problem on xda or somewhere else...
Sebster
Yes. Your not the only one. I'm in the UK and still on B121 and not received any ota updates. I'm hoping the MM ota will be rolling straight out to us this month.
Sebster97 said:
I bought my phone on dec 4th and until that time I didn't receive any updates for my phone.
I have the European PLK-L01432B121 Firmware but the only option for me is to update my phone manually which is kinda annoying.
Does anyone else experience this problem?
I didn't find anything related to my problem on xda or somewhere else...
Sebster
Click to expand...
Click to collapse
Yes - unless we've done manual updates or beta tests, most of the us are probably still on B121.
Not quite sure why you think this a problem though.
numbnutsuk said:
Yes. Your not the only one. I'm in the UK and still on B121 and not received any ota updates..
Click to expand...
Click to collapse
Same here numbnuts (like the name! :silly 2 phones did the same, signed up for mm beta, nothing
I even signed up for the Indian MM release for ****s n giggles.
lybad said:
Yes - unless we've done manual updates or beta tests, most of the us are probably still on B121.
Not quite sure why you think this a problem though.
Click to expand...
Click to collapse
A lot of people already got their Updates to B140 and B170 so I was wondering why I don't receive them via OTA...
It's a problem because I think it is very annoying to do a manual update every time a new update rolls out. When Honor implement a OTA feature, than it should work.
numbnutsuk said:
Yes. Your not the only one. I'm in the UK and still on B121 and not received any ota updates. I'm hoping the MM ota will be rolling straight out to us this month.
Click to expand...
Click to collapse
I've heard that with the release of the Honor 5x, MM for it will be rolled out the next days!
We're getting closer :good:
Hi sorry for necroing thread
i've still not gotten an OTA update yet for 6.0 mashmellow
anyone else have this issue? i'm on B180
morcup said:
Hi sorry for necroing thread
i've still not gotten an OTA update yet for 6.0 mashmellow
anyone else have this issue? i'm on B180
Click to expand...
Click to collapse
still on B121 no OTA whatsoever..........
O.
Im currently sitting on 6.0.
I signed up for the early update programme and it pushed the update though
oppossum said:
still on B121 no OTA whatsoever..........
O.
Click to expand...
Click to collapse
1. Backup with HiSuit all your stuff.
2. Factory reset phone.
3. Don´t setup any apps, just anything the setup wizard asks, including wifi and google account.
4. After completing setup, check for update.
5. After each update, repeat again from line 2.
6. At B730, restore HiSuit backup except for apps already included in the ROM.
Hi,
I have a problem with updates. I didn't recieve any OTA updates with my Honor 7.
I have updated my phone manually to B170 but i didn't before no updates for B130 and other updates.
Somebody a solution for this of have the same problem ?
Right now, people with b130 are receiving the ota update to b180 so you could have just waited. Now you can either manually update to b180 or b320 or just wait a week or two for final marshmallow release. I think it will arrive as ota to everybody
Wysłane z mojego PLK-L01 przy użyciu Tapatalka
Yes, But i didn't get any OTA the last few months, No OTA update for B130 and B170 and not for B180.
daveknoop said:
Hi,
I have a problem with updates. I didn't recieve any OTA updates with my Honor 7.
I have updated my phone manually to B170 but i didn't before no updates for B130 and other updates.
Somebody a solution for this of have the same problem ?
Click to expand...
Click to collapse
I got B130 rooted, and did recive a update today to B180. But it fails every single time at 9%... dont know what to do...
gmortena said:
I got B130 rooted, and did recive a update today to B180. But it fails every single time at 9%... dont know what to do...
Click to expand...
Click to collapse
Same problem
PlanetTeamSpeak said:
Same problem
Click to expand...
Click to collapse
you have to unroot the honor 7
in supersu app " Settings Full unroot"
Then flash orginal recovery.img with Honor 7 Multi-Tool.
Then you can run the uppdate
warning! use only the supersu unroot cause problem to me! better reflash the 130first
Inviato dal mio PLK-L01 utilizzando Tapatalk
yume-smart said:
warning! use only the supersu unroot cause problem to me! better reflash the 130first
Inviato dal mio PLK-L01 utilizzando Tapatalk
Click to expand...
Click to collapse
Plz can you explain how to reflash the 130. Plz
And after reflash b130 can i directly update B180?? If not can you tell me how many versions came after b130. Coz i want to install B320. How can i came up there easily plz explain me. Thnx advance
m.younusrahman said:
Plz can you explain how to reflash the 130. Plz
And after reflash b130 can i directly update B180?? If not can you tell me how many versions came after b130. Coz i want to install B320. How can i came up there easily plz explain me. Thnx advance
Click to expand...
Click to collapse
Go to updater in setting
select local update
select firmware file
and start flashing
daveknoop said:
Yes, But i didn't get any OTA the last few months, No OTA update for B130 and B170 and not for B180.
Click to expand...
Click to collapse
Had the same problem.
I had to update from B121 to all updates until B170. With the B170 I suddenly received B180 (two weeks ago I guess) ota.
There is no reason for that, I already talked to the costumer support of Honor.
But a Tip from me: Turn off Flight Mode so that you have a mobile signal. Then turn on wifi and see if you get an update via the EMUI Update app
Greetings Sebster
Sent from my Huawei PLK-L01 using XDA Labs
@Sebster97: I have the same problem, I'm on B130 (not rooted) now and my Updater says "No updates". And that tip doesn't work. And... I don't see why it should work anyway.
BogV said:
@Sebster97: I have the same problem, I'm on B130 (not rooted) now and my Updater says "No updates". And that tip doesn't work. And... I don't see why it should work anyway.
Click to expand...
Click to collapse
I've noticed, that, if you hit the update button and afterwards disable flight mode, the update app says "Look for updates" instead of "No updates available". So I tought, maybe with disabled flight mode you have the access to an update.
I also read it on other posts here.
Honor rolls out the updates in VERY strange stages. Nobody (maybe even Honor) doesn't know, how the useres in diffrent areas are able to update
Sent from my Huawei PLK-L01 using XDA Labs
Mine says "Check for updates" and "No updates" in either way, airplaine mode on or off.
I also tried several times to check for updates while being in another country, same result.
One thing you got right: Honor's way to seed the updates it's A MESS! After almost 2 months of using the phone, I've got only one update, from B120 to B130, while others are already on MM, using the same PLK-L01 European version. This is crazy!
BogV said:
Mine says "Check for updates" and "No updates" in either way, airplaine mode on or off.
I also tried several times to check for updates while being in another country, same result.
One thing you got right: Honor's way to seed the updates it's A MESS! After almost 2 months of using the phone, I've got only one update, from B120 to B130, while others are already on MM, using the same PLK-L01 European version. This is crazy!
Click to expand...
Click to collapse
I suggest, manually download and update from here or here
rspn69 said:
I suggest, manually download and update from here or here
Click to expand...
Click to collapse
+one
Thanks man
Is it possible to update the B140 too b320?
How?
update problem
rspn69 said:
Go to updater in setting
select local update
select firmware file
and start flashing
Click to expand...
Click to collapse
im using plk l01 and its on b130... ive tried alot to update automatically and via local... but both doesn't work for me. anyone pls help....
not working
Too51oll said:
+one
Click to expand...
Click to collapse
ive tried manually by downloading 6.0 ver for plk l01.. i downloaded.. unzipped.. putted into dload folder and pressed volume up+down and power.. it showed software is updating.. and when it reached 14 it shows failed..... ?
I just got an update to the November security patch for my Mi 9. Nothing much has changed visually from the previous version just a security patch
I think it rolled out pretty quick tbh.
Country: UK
I just got it in France, maybe there are a few bugs fixed, a security update is normally around 240 Mb as I know
got the notification last night, but now it's gone )
Installed manually.
Everything looks OK for now and I personally ddin't see any kind of change except android patch but again we will see during time, maybe is something which one can see so quickly.
EDIT
Now here is what I have noticed so far.
- Clicking on Settings->Security status->Google Play system update I got offer to update Security patch level to 1 October 2019.
- Under display fingerprint sensor works really, really quick, i would say instantly.
- Anti-flicker mode now works without any issue (turning on this option I would get rhythmic backlight change, pattern was about two times in one second from high to low).
- Entering *#*#4636#*#* in dialer and after that Phone information1 or Phone information2 there is new option present "Enable DSDS" and it's activated at me (I have two SIM's).
since the update i have a bootloop with the error gerätesuche wurde unerwartet beendet ( Device search ended unexpectedly )
cant use my mi 9 now
schwedenpower said:
since the update i have a bootloop with the error gerätesuche wurde unerwartet beendet ( Device search ended unexpectedly )
cant use my mi 9 now
Click to expand...
Click to collapse
Factory reset would help, maybe?!
maybe but all my data is after reset lost
schwedenpower said:
maybe but all my data is after reset lost
Click to expand...
Click to collapse
Yes, you always have to be prepared for that when you update a phone. I take it you have backups for all important stuff, right?
schwedenpower said:
maybe but all my data is after reset lost
Click to expand...
Click to collapse
Yes, but what's the alternative, leave phone one the shelf?!
Where is the link for manual instalation?
hellexplore said:
Where is the link for manual instalation?
Click to expand...
Click to collapse
Here You go!
https://bigota.d.miui.com/V11.0.6.0...QFAEUXM-V11.0.6.0.QFAEUXM-6709a792ca-10.0.zip
Jehonan said:
Here You go!
https://bigota.d.miui.com/V11.0.6.0...QFAEUXM-V11.0.6.0.QFAEUXM-6709a792ca-10.0.zip
Click to expand...
Click to collapse
This is global stable right? I'm on 11.0.2 global stable but i don't have recieved this ota yet.
hellexplore said:
This is global stable right? I'm on 11.0.2 global stable but i don't have recieved this ota yet.
Click to expand...
Click to collapse
No , this is EEA Global
hellexplore said:
This is global stable right? I'm on 11.0.2 global stable but i don't have recieved this ota yet.
Click to expand...
Click to collapse
No it's not!
This is EEA Global!
Here, this is latest Global version OTA update.
https://bigota.d.miui.com/V11.0.3.0...QFAMIXM-V11.0.3.0.QFAMIXM-cf0def2d5a-10.0.zip
Jehonan said:
No it's not!
This is EEA Global!
Here, this is latest Global version OTA update.
https://bigota.d.miui.com/V11.0.3.0...QFAMIXM-V11.0.3.0.QFAMIXM-cf0def2d5a-10.0.zip
Click to expand...
Click to collapse
Manually installed and changed to 11.0.3 and November security patch successfully!
I don't received notification, seems is has been retired
so, one question, can we flash this update via TWRP?! like, the EEA one? im rooted with magisk too, it will need root again?!
thanks in advance!
it's seems to back online.
Mahdian57 said:
Manually installed and changed to 11.0.3 and November security patch successfully!
Click to expand...
Click to collapse
Any problems with 11.0.3?
I worry about bootloop since my other xiaomi got bootloop after installing latest update. Never worried about this before, so I got to be more careful
foccacia said:
Any problems with 11.0.3?
I worry about bootloop since my other xiaomi got bootloop after installing latest update. Never worried about this before, so I got to be more careful
Click to expand...
Click to collapse
this issue (boot loop) was not happening
Hi!
I've recently purchased an EU 8/128 device and installed the realme ui update from the india website.
Now the nfc and brightness sensor don't work.
I've seen other users withba similar problem, but it isn't clear to me what should I do now: can I go back to coloros 6? Can the bugs be solved in any other way? Should I take the phone back for a refund?
Thank you in advance to anyone willing to give an advice.
NFC versions upgrade to India version will cause some problems like you said, I don't know if you upgraded to c03 or c01. The NFC versions just upgrade to c01. You can take it back to the service center and ask for help or you must wait for NFC c03 c04 firmware.
donkeyman1234 said:
NFC versions upgrade to India version will cause some problems like you said, I don't know if you upgraded to c03 or c01. The NFC versions just upgrade to c01. You can take it back to the service center and ask for help or you must wait for NFC c03 c04 firmware.
Click to expand...
Click to collapse
Thank you. How do I check wether I have c03 or c01?
The nfc version would be the realme ui update for global phones? Are you sure I'll be able to install it after it comes out?
See "About phone" in the setup.
You must have the firmware dowloaded before you update and turn the phone to recovery mode to update (because I doubt your phone will get ota), or you can try recovery mode online update.
donkeyman1234 said:
See "About phone" in the setup.
You must have the firmware dowloaded before you update (because I doubt your phone will get ota), or you can try stock recovery mode to online update.
Click to expand...
Click to collapse
We are talking about an hypothetical nfc version of realme ui, right?
Where would I be able to download it?
Thank you again for all the help. I'm a bit worried that I rendered my newly bought phone kinda useless ?
The global version comes with NFC. But when
you updated to India Rom ,NFC is gone. If you can't change back to global version, you may take it back to service center, I am sure it won't cost you anything, at least in my country they won't charge.
I drink from the keg of glory
donkeyman1234 said:
The global version comes with NFC. But when
you updated to India Rom ,NFC is gone. You may take it back to service center, I am sure it won't cost you anything, at least in my country they won't charge.
Click to expand...
Click to collapse
I managed to solve the issue.
I read in another thread that realme ui for nfc devices was avaiable in russia via OTA. So I downloaded the update from the official russian website (https://www.realme.com/ru/support/software-update) and proceded to install via recovery mode.
Much to my delight, it worked wonderfully! The NFC bug is gone as well as all the other ones (auto brightness, system updater)
Thanks to donkeyman1234 for the support
I am glad it can be rolled back to c01 via recovery mode. Hope everyone with global version using India Rom c01~c03 can restore back to global realme ui c01.
LucaLKS said:
I managed to solve the issue.
I read in another thread that realme ui for nfc devices was avaiable in russia via OTA. So I downloaded the update from the official russian website (https://www.realme.com/ru/support/software-update) and proceded to install via recovery mode.
Much to my delight, it worked wonderfully! The NFC bug is gone as well as all the other ones (auto brightness, system updater)
Thanks to donkeyman1234 for the support
Click to expand...
Click to collapse
Amazing news!!! I had the exact same problem with my Global version. I had version RMX1921EX_11_A.05 on my phone and installed the indian version of RMX1921EX_11_C.03 on top. It worked for the most part but full of the bugs already mentioned (battery drain, NFC stopped, auto brightness gone)
@LucaLKS was your model you got fixed an RMX1921EX or RMX1921EUEX?
@donkeyman1234 Do you think I will be able to do the same on my RMX1921EX and roll back from RMX1921EX_11_C.03 to a C.01 through stock recovery?
Cheers guys
mario0788 said:
Amazing news!!! I had the exact same problem with my Global version. I had version RMX1921EX_11_A.05 on my phone and installed the indian version of RMX1921EX_11_C.03 on top. It worked for the most part but full of the bugs already mentioned (battery drain, NFC stopped, auto brightness gone)
@LucaLKS was your model you got fixed an RMX1921EX or RMX1921EUEX?
@donkeyman1234 Do you think I will be able to do the same on my RMX1921EX and roll back from RMX1921EX_11_C.03 to a C.01 through stock recovery?
Cheers guys
Click to expand...
Click to collapse
I don't know where to check. I can't find it in about phone
LucaLKS said:
I don't know where to check. I can't find it in about phone
Click to expand...
Click to collapse
There is an app called AIDA64 in google store which reads the system information. Could you please download and screenshot the system and android tabs? I will be able to compare our phones and see whether their are the same or not. Cheers
mario0788 said:
Amazing news!!! I had the exact same problem with my Global version. I had version RMX1921EX_11_A.05 on my phone and installed the indian version of RMX1921EX_11_C.03 on top. It worked for the most part but full of the bugs already mentioned (battery drain, NFC stopped, auto brightness gone)
@LucaLKS was your model you got fixed an RMX1921EX or RMX1921EUEX?
@donkeyman1234 Do you think I will be able to do the same on my RMX1921EX and roll back from RMX1921EX_11_C.03 to a C.01 through stock recovery?
Cheers guys
Click to expand...
Click to collapse
I think you should give it a try. Just download the firmware and boot into recovery mode. I hope you make it. (It won't hurt if you can't flash it)
donkeyman1234 said:
I think you should give it a try. Just download the firmware and boot into recovery mode. I hope you make it. (It won't hurt if you can't flash it)
Click to expand...
Click to collapse
Absolutely correct. Already downloading. My only concern is that my version was RMX1921EX and this one is RMX1921EUEX. Hopefully nothing will get bricked. I'm crossing my fingers for it to work :fingers-crossed:
mario0788 said:
Absolutely correct. Already downloading. My only concern is that my version was RMX1921EX and this one is RMX1921EUEX. Hopefully nothing will get bricked. I'm crossing my fingers for it to work :fingers-crossed:
Click to expand...
Click to collapse
If your phone comes with NFC then it is global (not India), that's why when you updated to India Rom, the NFC is gone.
donkeyman1234 said:
If your phone comes with NFC then it is global (not India), that's why when you updated to India Rom, the NFC is gone.
Click to expand...
Click to collapse
I know for a fact that when I bought the phone, I bought the global version and had NFC on board but I'm really confused with Realme's naming and monikers. So let me get it clear.
RMX1921EX is the Indian version?!
RMX1921EUEX is the Global version?!
If that's correct, why did my phone had the version RMX1921EX_11_A.05? That means that RMX1921EX is assigned to both Indian and Global versions? that's what has me confused.
mario0788 said:
There is an app called AIDA64 in google store which reads the system information. Could you please download and screenshot the system and android tabs? I will be able to compare our phones and see whether their are the same or not. Cheers
Click to expand...
Click to collapse
Here you have
https://postimg.cc/JG8tCYZ4
https://postimg.cc/rDQvwsHY
LucaLKS said:
Here you have
https://postimg.cc/JG8tCYZ4
https://postimg.cc/rDQvwsHY
Click to expand...
Click to collapse
Thank you brother. I think you have the EUEX version but still im going to try and install and see what happens!
mario0788 said:
Thank you brother. I think you have the EUEX version but still im going to try and install and see what happens!
Click to expand...
Click to collapse
Let me know what happens.
Speriamo bene
LucaLKS said:
Let me know what happens.
Speriamo bene
Click to expand...
Click to collapse
I DON'T even believe it!!! IT WORKED!!! Finally my phone is optimal again!!! Guys thank so so much !!!
Let's spread the word to everyone who had the same issue!!
:laugh::laugh::laugh:
@LucaLKS
@donkeyman1234
mario0788 said:
I DON'T even believe it!!! IT WORKED!!! Finally my phone is optimal again!!! Guys thank so so much !!!
Let's spread the word to everyone who had the same issue!!
:laugh::laugh::laugh:
@LucaLKS
@donkeyman1234
Click to expand...
Click to collapse
Great!
Hello.
I have a problem with a new Huawei mate 20 pro LYA-L29 running on 9.0.0.243(AUSC636E11) recieved on insurance.
Iam not able to update this software at all. I live in Norway. I also get an error that prevent me from using Google Pay: -Phone is rooted-, wich it is not. (tested with cpu-z.)
I have been in contact with Huawei support who did a remote diagnose as well. They couldent help me further.
They want me to send the phone in to service, but it would be great if I could just solve it my self...Had the phone in for service/fix for 2 month already..
So, is there any way to fix this and get latest update?
moded hisuite and update over it
CROrION said:
moded hisuite and update over it
Click to expand...
Click to collapse
Did yesterday and finally managed to update to 9.1.0.359
GizmoPower said:
Did yesterday and finally managed to update to 9.1.0.359
Click to expand...
Click to collapse
And today updated to 10.0.0.181(C432E7R1P5)
I managed with this update to change region to EU and now my google pay works again.. happy days
Should I go further up, or am I ok?
GizmoPower said:
And today updated to 10.0.0.181(C432E7R1P5)
I managed with this update to change region to EU and now my google pay works again.. happy days
Should I go further up, or am I ok?
Click to expand...
Click to collapse
Go for it, latest i eu is 11.0.0.200
Done. Thank you
And a big thanks to the creator of this method.
Very easy and saved me big time..
Donation made
Latest EU (C432) is now 12.0.0.132