Hi, my Moto z ,with lcd broken, after i replace the lcd it's broken again. and i have a lot of problem after the last replacement, infact the phone, not turn on, so i thougth it was the battery, but after change whit a new, the phone still not to turn on.
So i think, Maybe it should be recharge the battery, so i let him on charge for 4 Hours.( whit the original charger) but him still not turn on. And then i choose to let lose.
A few day a go, i decide to plug the phone to my pc (The phone is whitout battery, because the new one i selled it), and magically it turn on, but still a problem, a big problem, the phone not showing on pc, the Pc not recognize the phone, even go to device management (on windws 10) it not show.
I try a lot of things, but still not to recognize the phone to pc. So anyone can help me? my point is to have access to my memory.
P.S: the phone is still conected to wifi, so maybe can i "Hack" the phone? to have access to my memory?
P.P.S: Sorry for my bad english
Related
I successfully flashed my X10 with 2.1 and had no issues. I believe last week I got the multitouch update from SE. No problems. Today however, I had a major problem. I was testing a program called Blacklist by calling my phone from another phone to see if it works. When I went to slide the slide over to send the call to voicemail, the phone buzzed for about two seconds and shut off. When I tried to turn the phone back on it buzzed like it should and that was it, nothing. I updated the phone with the PC Companion, the Update service, and it updated and reinstalled the software according to the program but still wouldn't turn on. I tried to reflash the phone using the X10 Flash tool from this site; it flashed successfully but still nothing. I even left the battery out of the phone while I was at work; still nothing happened. So with all this, any ideas???
Does anybody recognize this and have any suggestions?
I would contact the dev who created Blacklist.
I don't think it was Blacklist that caused it. Even when I reflashed the OS it still had the same problem. My friend mentioned about flashing the baseband. But I'm trying to see what this forum has to say.
If it was the OS, then SEUS or PC Companion "repair software" should work. It basically wipes your phone and does a fresh install, which would fix any errors you created.
Also, try this... Remove the battery and leave the back off the phone. Then plug the phone into the charger/wall with the battery out. Wait for a minute or longer, and then insert the battery while it is still plugged in. Wait a minute, and then try and turn the phone on. If it doesn't work, try altering the steps a bit like starting with the phone plugged in, or plugging it into usb port on your PC rather than the wall. I haven't had to do this myself, but I read somewhere that this works when the x10 dies.
I hope this helps. Let us know how it turns out.
I just tried this and still nothing. I am going to try to downgrade to 1.6 and see what happens.
I downgraded to 1.6 and still nothing.
Forgive me if these questions appear naive or insulting....
Sometimes (actually most times) it is something simple, so let's back up. Since it vibrates when pressing power on button, it would appear the phone's power circuit is functional. How much charge did you have left in the battery when this happened? What happens with the LED notification light when you plug it in to charge? Basically, are you sure the battery isn't dead or worse bad? A red/pink LED notification would be a sign the battery is charging/working.
**If it is not charging check to see if the USB cable or port damaged? I think my usb cable quit working after my first flash. I thought it was my phone until I read about usb cables suddenly not working after flashing... weird? Now I use an HTC cord.
use x10 flash unbricker it solved all my problems when my phone would work.
Hey i had this problem (but i dont have the MT update yet ) but it was my memory card stopping the X10i to not turn on :s try a new memory card XD
@agentJBM
I thought about the same thing last night, so I plugged the phone into the charger for the night. The battery feels warm like it's been charging. When I plug the charger in the green light comes on for a bit then turns off, which is normal. However, still the same issue.
@soldier33 Do you have a link???
@Si-The-Spike I thought about this before. I pulled the memory card and the sim card out and tried to see what would happen, nothing.
I at least know this much: the phone is able to be put into flash mode, and the phone is able to accept a charge. I just can't figure out why it can't boot.
I cant seem to find a working lnik anymore. So ill upload the one I have saved. Hoepfully it works.
Much appreciated
sorry it taking so long got very slow upload speed just 20kb. and the file size is 130mb
here you go zshare.net/download/87207469347a26f2/
Thanks. I'll try it out tonight.
Unfortunately it did not work. I'm completely lost on what happened.
Try completely uninstalling SEUS, PC Companion, and Flash Tool & firmware from your PC. Do a fresh install of SEUS and then try to update/repair software. I read it may take 4 or so attempts, especially if you are having battery trouble.
I've never done it but there is a way to open in safe mode as well by pressing menu button while turning phone on. Try searching that as well.
my x10 worked almost correctly, then my friend called me. when i want end call, my phone frozes. i taked battery off. now i cant turn phone on. yesterday it turn itself off then i connect phone with pc, nothing happened. i take sim card off and tryng again, then phone charge. i m put sim back and phone works. today i trie it wit usb and charger but nothing hapend whats the problem an how to fix it?
Hi guys,
I'm repasting what I wrote in my previous thread hoping you can have a clearer view of my issue.
My phone has the standard ROM, WP 6.5, nothing changed
I never flushed the phone, never formatted it, etc, everything is legit!
My TG01 has died many months ago and now I'm looking into ways of having it re-activated. I will explain to you my possible theories why it died, so maybe some of you will have an idea how to fix it
- For the first 4-5 months I only used PC USB (synchronization) charging, as I had a UK mains which obviously does not work in Europe. I noticed that the battery indicator was never really accurate, showing me the battery levels very vaguely.
- I often synchronized my Outlook e-mails with my mobile phone, one day my phone died when I chose to synchronize all e-mails. It died to an extent that the battery was completely empty. My PC wouldn't recognize it and it would only start for 5 seconds (the red led lamp would shine) and then die...
I somehow managed to revive it with my normal charger but afterwards it used to overheat quite a lot...
- One day I left it to synchronize again and the battery died on me again (at least that's what I think had happened)... the difference that USB PC charging did not work anymore as well mains charging. I was desperate enough to buy a replacement battery from eBay and I still have the same story. When I connect the phone to the charger I don't even see the diode lighting up anymore.. NOTHING. Any tips?
Could it be that the replacement battery is also so empty that even a mains can't charge it anymore? I heard someone mention something with cutting a wire etc, ... would that help me? IF so.. how do you exactly do that?
Thanks!
Hi guys,
So far no luck in getting updates from you, but I've got an update for myself:
I somehow managed to get the LED diode turn red when I connected it to the computer, which should be indicating the fact that the phone is charging, right? When I try to power it up the device manager recognizes a device called TOSHIBA DL... does this mean my phone is in some sort of emergency state?
The screen lights up a bit as well, but remains black.
yess this means your tg01 is NOT bricked. try take your battery out and put it back in so its totaly switched off then press n hold CAMERA, VOL UP, POWER keys to perform a master reset. if that doesnt work try this,
use the short pin method, put a .tsw in a PRG folder at the root off your sd card and short pins 1 and 3
if not,
download a tg01 rom in a .bin and flashh the .bin via tgdownloader
if you dont know these methods please tell me and i will link and help you.
Hi!
Thanks for your reply. If you could guide me a bit with the pins method, that would be great.
Also, when I plug in the mobile phone to charge now the red light is now flashing, instead of remaining constant, what could that indicate?
Phone never turns on now
hi there, it sounds like your battery has gone flat try leaving it on charge via USB for a few hours see if that will kickstart it and for the pin method
http://forum.xda-developers.com/showthread.php?t=654674
try to charge your battery first as it may just be a flat battery but if not you may need to reflash your rom via the pin method
if there are any problems or you are unsure message me back
Well, my RAZR XT910 screen broke some time ago. In pocket. You know, this whole issue thing with them.
Anyway, I finally want to try fix it. So, Screen is dead, touch too. But I can't give it to service repair, so I want to replace screen myself.
But, before I do it, I wanted to try if phone works. So, I charged it, turned on (without sim card and sdCard).
And.. yeah. Notification light works. I see. I had installed Light manager. It informs me about no sim. I connected it to USB. And... Internal storage is empty. Strange. I had ton of stuff on it. Anyway, I inserted sdCard and connected phone to USB again. Aaannddd... It does not detect external storage.
So.... My question. Can something else be broken on my phone? I don't want to buy LCD and after replacing it I'll realize that phone itself is also screwed up. And how to check if it works without screen?
Hey there. I found a bit old phone in my house, Huawei G730-U10 with MTK6582. Here's problem:
Phone won't turn on at all (no reaction) with battery in and USB out.
With battery in and USB in (connected to charger or PC, no matter what), at first it turns on red led that stays still, and after some time it starts vibrating with interval of about 10 seconds and PC sees it for 2 secs (it connects and after 2 secs - disconnects), then everything repeats. I assume it's bootlooping, but there's no anything on screen (it doesn't even turn on, full darkness). This continues even after taking out USB, only way to stop it - take out battery and place it back.
With battery out and USB in, red led starts blinking with very quiet beeping (very very very quiet).
As you could guess - recovery, fastboot and other things aren't working.
I've checked main board, everything is ok, connected and working fine.
I think there's problem in ROM (not firmware ROM, but ROM that's read-only memory). Something's wrong, maybe there's wrong preloader (or there's no preloader at all), maybe boot partition is damaged, I don't know.
Service center tried to fool me on buying new board for 100$ (althrough it costs 40 on aliexpress), I think they didn't even look at it, so I can't trust them.
I don't need suggestions like "try to flash new rom", you think I didn't try? How is this possible if I can't make PC to see phone for more than 2 secs? Flashtool isn't working even without battery mode.
Do you have any ideas?
Thanks for help.