Related
I have just received my Iocean X7 Elite and was about to install a new rom. I had successfully rooted the device and then was trying to flash
the recovery with SP Flash Tool.
After the recovery flashed my phone refuses to turn on I believe its somehow bricked but have no idea how this could have happened. I did
format flash i only downloaded the recovery to the device.
In Device Manager when i plug the phone it it either shows up as 'DA USB VCOM Port' or 'MTK USB Port'.
When I try to use SP Tool to flash the stock Rom back onto the device I get an error saying 'BROM ERROR : S_FT_ENABLE_DRAM_FAIL(4032)'
I have no idea what to do next can someone help me.
I have tried what this thread suggests:
bump
same as u..but differ phone model.(N9589)
had a few upgrd...til the recent brick it.
Tried a few version of flash tool and still the same
Joshafc said:
I have just received my Iocean X7 Elite and was about to install a new rom. I had successfully rooted the device and then was trying to flash
the recovery with SP Flash Tool.
After the recovery flashed my phone refuses to turn on I believe its somehow bricked but have no idea how this could have happened. I did
format flash i only downloaded the recovery to the device.
In Device Manager when i plug the phone it it either shows up as 'DA USB VCOM Port' or 'MTK USB Port'.
When I try to use SP Tool to flash the stock Rom back onto the device I get an error saying 'BROM ERROR : S_FT_ENABLE_DRAM_FAIL(4032)'
I have no idea what to do next can someone help me.
I have tried what this thread suggests:
Click to expand...
Click to collapse
Same problem here - tried to install stock firmware and got this error...
these are common problems when flashing MT65xx based phones,
ie : error 4008, 4xxx, 5xxx whatever those codes mean, no explanation after extensive search on google.
once I managed to flash this one phone successfully, but I don't know exactly what I did.
as long as I recall, I tried to delete the whole flashtool folders, re-extract them, let the phone cool down a bit
and oh, try to press volume up, or down button (varies on devices) while connecting to USB, once the flashing progress bar starts, release the button.
In the flashtool option, at the OPTIONS-->DA DOWNLOAD ALL-->, check WITHOUT BATTERY.
and in the option, DA DOWNLOAD ALL--> SPEED, check DO NOT SWITCH SPEED.
try flashing your phone without battery inserted, it works many times for me.
NOTE : BEWARE, flashing your MTK65xx based phone, sometimes this tool tried to REMOVE YOUR PHONE's IMEI information, so take caution !
I haven't managed how to prevent IMEI removal when flashing those phones, because I'm not a developer.
Hope this helps.
tukulll said:
these are common problems when flashing MT65xx based phones,
ie : error 4008, 4xxx, 5xxx whatever those codes mean, no explanation after extensive search on google.
once I managed to flash this one phone successfully, but I don't know exactly what I did.
as long as I recall, I tried to delete the whole flashtool folders, re-extract them, let the phone cool down a bit
and oh, try to press volume up, or down button (varies on devices) while connecting to USB, once the flashing progress bar starts, release the button.
In the flashtool option, at the OPTIONS-->DA DOWNLOAD ALL-->, check WITHOUT BATTERY.
and in the option, DA DOWNLOAD ALL--> SPEED, check DO NOT SWITCH SPEED.
try flashing your phone without battery inserted, it works many times for me.
NOTE : BEWARE, flashing your MTK65xx based phone, sometimes this tool tried to REMOVE YOUR PHONE's IMEI information, so take caution !
I haven't managed how to prevent IMEI removal when flashing those phones, because I'm not a developer.
Hope this helps.
Click to expand...
Click to collapse
Thank you for your reply, but this doesn't help... ;(
Anyone?
I think I figured out that the error above means you are trying to flash an incorrect ROM. Make sure you are using the right one and also make sure you're using the latest version of sp flash tool.
Once I downloaded a later version of the flash tool it began installing the ROM but then a different error appeared.
So I formatted the nand with the sp flash tool.
Then I flashed the stock ROM again and it worked
Formatting it seemed to make the errors go away even though its advised not to do so.
Sent from my iOCEAN X7 using xda app-developers app
vessk0 said:
Anyone?
Click to expand...
Click to collapse
I fixed this error by completely removing and reinstalling other drivers for mtk vcom loader
anyone heard Iocean will recall all of the x7 elite's? i've had a mail today they should do it, but i don't know if it's true or not.
Schumi_wk said:
anyone heard Iocean will recall all of the x7 elite's? i've had a mail today they should do it, but i don't know if it's true or not.
Click to expand...
Click to collapse
I haven't heard about that. Maybe its a fake email. Did it say what the fault was?
Joshafc said:
I think I figured out that the error above means you are trying to flash an incorrect ROM. Make sure you are using the right one and also make sure you're using the latest version of sp flash tool.
Once I downloaded a later version of the flash tool it began installing the ROM but then a different error appeared.
So I formatted the nand with the sp flash tool.
Then I flashed the stock ROM again and it worked
Formatting it seemed to make the errors go away even though its advised not to do so.
Sent from my iOCEAN X7 using xda app-developers app
Click to expand...
Click to collapse
How to format the nand with sp flash tool, I use the latest version?
And can you point me to good original stock ROM?
Thank you!
lolet said:
I fixed this error by completely removing and reinstalling other drivers for mtk vcom loader
Click to expand...
Click to collapse
I tried reinstalling drivers, also tried other drivers, but this doesn't help...
I've had the same problem with the following installation Sp Tools
SP_Flash_Tool_exe_v3.1316.0.150
Rom: MP_mt89_v9_iocean_ousheng_jb2_20130520-184014_zhongyeqing_PC
http://d-h.st/ESX
Iocean X7 Youth
I don't have the same problem but i flashed the latest version of official rom for iOcean x7 Youth : 03 july 2013 : and wtf no more internal sdcard only the rom stockage. So i can't download anything, i can't use camera .
On the official website, I read that before flashing the 20 may 2013 rom one and the 03 July 2013 one, your baseband version have to be 23/04 or higher( you have to flash the 23/04 official rom first). This is only avalaible for the YOUTH version.
So tomorrow i will try what i said below to see if i have internal sd card again.
noob question::: since the iocean x7 young and turbo are the same phones...only different clock rates...will flashing the firmware for turbo on iocean x7 young work??assuming that the mtk6589T and mtk6589 are the same chipset only different clock rates??
Micromax A116 (Cant flash Rom)Brick Problem Solved
tukulll said:
these are common problems when flashing MT65xx based phones,
ie : error 4008, 4xxx, 5xxx whatever those codes mean, no explanation after extensive search on google.
once I managed to flash this one phone successfully, but I don't know exactly what I did.
as long as I recall, I tried to delete the whole flashtool folders, re-extract them, let the phone cool down a bit
and oh, try to press volume up, or down button (varies on devices) while connecting to USB, once the flashing progress bar starts, release the button.
In the flashtool option, at the OPTIONS-->DA DOWNLOAD ALL-->, check WITHOUT BATTERY.
and in the option, DA DOWNLOAD ALL--> SPEED, check DO NOT SWITCH SPEED.
try flashing your phone without battery inserted, it works many times for me.
NOTE : BEWARE, flashing your MTK65xx based phone, sometimes this tool tried to REMOVE YOUR PHONE's IMEI information, so take caution !
I haven't managed how to prevent IMEI removal when flashing those phones, because I'm not a developer.
Hope this helps.
Click to expand...
Click to collapse
Thanks a lot. My Micromax a116 was brick. Now its alive.
Here I am with the same problem in a N920e... AND IT'S NOT MINE! :crying:
I'll have to pay it to the owner if I can't solve this:
DaniPhii said:
Here I am with the same problem in a N920e... AND IT'S NOT MINE! :crying:
I'll have to pay it to the owner if I can't solve this:
View attachment 2243401
Click to expand...
Click to collapse
Clearly: Wrong driver. I had also this error. SPflash tool did not readback. I did not flash anything! I fixed this by showing the nonpresent devices in devicemanagement (google for show nonpresent devices for explanation)
Go to com ports, and delete all mediatek drivers except preloader driver. Now start over. It can help if you choose the same usb port where you had success last time.
SP flash tool shows in the statusbar which driver it is using.
mistraller said:
Clearly: Wrong driver. I had also this error. SPflash tool did not readback. I did not flash anything! I fixed this by showing the nonpresent devices in devicemanagement (google for show nonpresent devices for explanation)
Go to com ports, and delete all mediatek drivers except preloader driver. Now start over. It can help if you choose the same usb port where you had success last time.
Click to expand...
Click to collapse
Yes, you got it
SP Flash Tool couldn't find my phone, but now it works
It's exactly a windoze driver problem.
Going to devicemanagement, in LAN-Devices I a had an Alcatel device,
chosing driver by hand and use the mtk usb driver, now Flashtool finds the phone
Thanks a lotttttttt....
shiv.kbh said:
Thanks a lot. My Micromax a116 was brick. Now its alive.
Click to expand...
Click to collapse
Thanks a lot man i unbricked my bolt a58 with this...thanks thanks...
Hello guys I got a x920 and was working good until it started doing something similar like Samsung Galaxy S3 Sudden Death.
The phone would randomly get a screen freeze, and the half bottom of the screen got distorted like green and pink lines, then slowly, the pixels were turning to black until the whole screen gets black, but the backlight would remain on.
I had to pull the battery out, and sometimes the phone would work again instantly, some other times, it wouldn't turn on, only after some time, and after a lot of battery pulls.
But last time I got this sudden death, the phone never came back.
I had the stock rom and only root.
My model version is: e2001v21_v89_zlh_hd
Most people with this phone have the e2001_v89_zlh_hd, and most roms on needrom.com are for e2001_v89_zlh_hd, there are a lot of roms for e2001v21_v89_zlh_hd though but I tried everything and I got DRAM Failed.
I use windows 8
SP flash tool v3.1304.0.119, v3.1308.0.125, v3.1316.0.150
And several other roms for both versions.
There is a solution from a French guy about the DRAM failed problem here, but I got the S5 rom downloaded as he stated, and can't get pass the first red bar on SP flash tool.
Do you have any idea what is going on with the 2 versions of the phone? People say that they read on chinese forum that v2.1 (e2001v21_v89_zlh_hd) has got different EMMC. So I guess roms from the e2001_v89_zlh_hd wont work.
I would like to know if you guys have any working rom for my e2001v21_v89_zlh_hd because I really need the phone at the moment. I must get it back to life.
ps (Is windows 8 suitable for flashing? I have installed mtk drviers normally through a weird process enabling manual driver installation through the advanced startup thingy on Windows 8, otherwise it wouldn't let me install the drivers.)
Voliminal_8 said:
Hello guys I got a x920 and was working good until it started doing something similar like Samsung Galaxy S3 Sudden Death.
ps (Is windows 8 suitable for flashing? I have installed mtk drviers normally through a weird process enabling manual driver installation through the advanced startup thingy on Windows 8, otherwise it wouldn't let me install the drivers.)
Click to expand...
Click to collapse
ok, there is no difference for using window 8 , xp, win 7, as long as u have installed the driver correctly.
as u said u can see the red bar, that mean yr driver was installed correctly.
all u need is the right preloader.bin
as i can understand from my past experiance, i think that the later batch of the phone, the manufacturer might use different DRAM or they might have changed the coding of the ram. that is why we see quite often there is complaint of DRAM fail when u try to flash the official rom for the phone. Not for newer model of the phone ( yr phone has two/three batches).
so may be u could ask the http://www.needrom.com/mobile/star-tengda-x920/ - smartdigi to create a preloader.bin from their phone for u , then u replace the preloader.bin in yr rom and flash it.
smartdigi is a team from Greece, and so am I, so yes, I just sent a message.
I hope I'll find a solution.
Voliminal_8 said:
smartdigi is a team from Greece, and so am I, so yes, I just sent a message.
I hope I'll find a solution.
Click to expand...
Click to collapse
i had read tru the needrom wed regarding thier rom, i saw there is a instruction to pass tru the "DRAM fail."
had u tried that before.
they also had rom that match with yr version.
Yes, I downloaded the rom, and still got DRAM failed.
Is there any way to install smartdigi rom through sp flash tool and not sd card?
here's the link http://www.needrom.com/mobile/star-tengda-x920
Yes, I downloaded the rom, and still got DRAM failed.
Is there any way to install smartdigi rom through sp flash tool and not sd card?
here's the link http://www.needrom.com/mobile/star-tengda-x920
Voliminal_8 said:
Yes, I downloaded the rom, and still got DRAM failed.
Is there any way to install smartdigi rom through sp flash tool and not sd card?
here's the link http://www.needrom.com/mobile/star-tengda-x920
Click to expand...
Click to collapse
ok, i just want to know if the procedure as they decribe will work, as i cannot test it, as i don.'t have the phone.
did u manage to get the preloder from them.
if u get the preloader from smartdigi , u stilll get the "DRAM fail" , then i think , may be their phone is an older batch,
for me, if u can read back from from the SP flash tool, (version 3.1316, (i justy learn that there is v3.1328 available)), then definitely u can flash yr phone with this preloader.bin
note
since u can't even go to recovery, then there is no way u can flash the rom with card flash rom from smartdigi, the only way to recover yr phone is tru cable flash rom that mean, u have to pass tru the "DRAM fail"
Well, I found the problem, the drivers installed are MTK USB Port, and not Preloader VCOM drivers.
I use windows 8 x64, I restarted with bypassing the signature thing.
The problem is, when I try to manually select the vcom driver, after the installation it shows up as MTK USB Port, and not as a vcom port.
Any solution?
Voliminal_8 said:
Well, I found the problem, the drivers installed are MTK USB Port, and not Preloader VCOM drivers.
I use windows 8 x64, I restarted with bypassing the signature thing.
The problem is, when I try to manually select the vcom driver, after the installation it shows up as MTK USB Port, and not as a vcom port.
Any solution?
Click to expand...
Click to collapse
no, it does not matter if it is preloader port or vcom port, actually they don,t make difference if u flash the rom.
that mean yr computer is talking to the phone correctly.
now the most important part is the "preloader.bin" file in yr rom must match the dram in yr phone.
that is why u hve to ask who has yr exactly same model of yr phone to create a preloader.bin.
or just try to download the preloader.bin as many as u can.
if u have a friend who has the phone same as as yours, then i can help to create from his phone, or u can create the preloader.bin from his phone
edit,
try to download the latest sp flas tool v3.1324 or v3.1328 ,flash the rom with it.
I tried several roms, with different preloader.bin files, non seems to work.
I tried with all sp flash tool versions, all 3.13904.0.119, 3.1308.0.125, 3.1316.0.150, 3.1328.0.183
Some versions of SP, are not showing up all the files gathered from the scatter file. Some other do.
Well, a smartdigi member, told me to use windows 7, because the mediatek drivers have gone as fas as windows 7 x64.
Voliminal_8 said:
I tried several roms, with different preloader.bin files, non seems to work.
I tried with all sp flash tool versions, all 3.13904.0.119, 3.1308.0.125, 3.1316.0.150, 3.1328.0.183
Some versions of SP, are not showing up all the files gathered from the scatter file. Some other do.
Well, a smartdigi member, told me to use windows 7, because the mediatek drivers have gone as fas as windows 7 x64.
Click to expand...
Click to collapse
ya, u could try with win7.
for me i can flash with win8 also.
i use win 7 at home, win8 at office, no problem.
u could try with win7, i think most likely , u will get the same result.
i had brick my s7589, i unbrick it with the right preloader. after that i tried with the preloader.bin that was originally came with the rom.
this time , it can pass tru the "dram fail", get the purple color, then yellow, then finish with green color. then i try to swith on the phone, but, no response from the phoe. it was bricked again.
then i flash back with the right preloader.bin, the phone back to life again.
did u manage to get preloader.bin from smartdigi?
for me, it is the best solution to unbrick the phone. may be there is some other ways that i don't know
stevenma61 said:
ya, u could try with win7.
for me i can flash with win8 also.
i use win 7 at home, win8 at office, no problem.
u could try with win7, i think most likely , u will get the same result.
i had brick my s7589, i unbrick it with the right preloader. after that i tried with the preloader.bin that was originally came with the rom.
this time , it can pass tru the "dram fail", get the purple color, then yellow, then finish with green color. then i try to swith on the phone, but, no response from the phoe. it was bricked again.
then i flash back with the right preloader.bin, the phone back to life again.
did u manage to get preloader.bin from smartdigi?
for me, it is the best solution to unbrick the phone. may be there is some other ways that i don't know
Click to expand...
Click to collapse
Well... installed windows 7 in another partition.
It was like I never did it, exactly the same result. Everything behaved the same.
I don't know... maybe I have crappy mtk drivers, or I'm doing something wrong while installing them.
Let me describe the steps, and if I'm somewhere wrong you can tell me.
Well, after a clean windows 7 install, I connect the phone to the pc (with or without battery,I think I tried both, didn't see something change) it gets to "other devices" as an "unknown device". right click to update driver software, select the folder with vcom drivers.
It gets recognized as a mtk usb port.
Try to flash like that, same results.
Then I go to update driver again, but this time I click "let me pick from a list of device drivers on my computer." I uncheck show compatible hardware, then I choose MTK Preloader USB VCOM Port.
the device now shows up to the device manager as "MTK Preloader USB VCOM Port".
Try to flash, everything is the same...
I read somewhere, that the normal installation of vcom drivers is kinda different, that it get's shown up as "MTK Preloader USB VCOM Port" right away, and I read that when you install the vcom driver correctly, it connect and disconnects the device every 3 seconds.
Well.. I didn't manage to get the preloader.bin yet, I'll ask for it, but why the official rom on needrom.com preloader.bin is not working with my phone? And why would smatdigi preloader.bin would work for me?
I tried roms that are for e2001v21_v89_zlh_hd but even their preloader wouldn't work for me.
first of all, stop playing with those preloaders. random flashing will brick your motherboard of your computer too, if you flash a wrong BIOS file. clear? okay. the DRAM error occurs if the Rom is mismatching the "signature" of your device. so, before trying to flash it, take another one, in this case, the right one. ( for example: my device (n9770) got few cameras, few board revisions, ddr or ddr2 Ram and so on, only one Rom or a mix of different files will work)so flashing a wrong firmware causes more "damage" or "errors". have you backed up your firmware before rooting?
you need to find a full backup of your device ( most likely a Rom directly from your vendor) including ALL needed partitions for flashtool. ROM's of new devices are hard to find, even for n9770 (mt6577) there are ROM versions from 06-2012 till now. so, if you got a "newer" device, you need to get the correct firmware and flashtool should flash without problems. also, your drivers are working perfectly, otherwise flashtool won't show the red bar wich is checking the device.you may need to check if the "second" driver is installed correctly, because the device will switch from preloader mode to "flash mode". maybe the driver for the preloader is installed correctly, but it can't switch to flash mode.
Chrizzly92 said:
first of all, stop playing with those preloaders. random flashing will brick your motherboard of your computer too, if you flash a wrong BIOS file. clear?
Click to expand...
Click to collapse
Clear bro, but I never really managed to do a flash. Just never. I only get dram failed.
Chrizzly92 said:
okay. the DRAM error occurs if the Rom is mismatching the "signature" of your device. so, before trying to flash it, take another one, in this case, the right one. ( for example: my device (n9770) got few cameras, few board revisions, ddr or ddr2 Ram and so on, only one Rom or a mix of different files will work)so flashing a wrong firmware causes more "damage" or "errors". have you backed up your firmware before rooting?
Click to expand...
Click to collapse
I don't think I did any more harm, since nothing really fot flashed.
Not I don't have a backup :/
Chrizzly92 said:
you need to find a full backup of your device ( most likely a Rom directly from your vendor) including ALL needed partitions for flashtool.
Click to expand...
Click to collapse
I bought it from focalprice, even if they send me any rom, it will be one of the officials found in needrom.com ... So I don't think they'll handle it.
Chrizzly92 said:
also, your drivers are working perfectly, otherwise flashtool won't show the red bar wich is checking the device.you may need to check if the "second" driver is installed correctly, because the device will switch from preloader mode to "flash mode". maybe the driver for the preloader is installed correctly, but it can't switch to flash mode.
Click to expand...
Click to collapse
How can I check that the second drivers is installed correctly?
just open your device manager and check, if the device gets recognized correctly. start a flash and check, if there are any devices gets loaded while trying to flash. if so, install the correct driver. there are some issues with that sometimes.
if this won't work, try using MTD tool. flasing through there should work always, but it got some issues with vcom drivers. you need to assign every vcom port to the mtk device. explaining of this is retty hard since english isn't my motherlanguage, so its best to check google or xda for that.
also, can you start your device into recovery, or is it really "dead"? no bootlogo, nothing?
No the device is hard bricked, no recovery at all. Not anything. :/
I can't use MtkDroidTool, it doesn't detect my device.
hmn, i would suggest its a hardware failure. never saw a device "dying" without flashing before.
btw: i meant SPMultiPortFlashDownloadProject tool, this is a more advanced variant of sp flash tool. just google for it and put a log in here, so i (we) can check whats the matter.
Chrizzly92 said:
hmn, i would suggest its a hardware failure. never saw a device "dying" without flashing before.
btw: i meant SPMultiPortFlashDownloadProject tool, this is a more advanced variant of sp flash tool. just google for it and put a log in here, so i (we) can check whats the matter.
Click to expand...
Click to collapse
I already have this tool and used it with the same results.
Which log do you need? It has 3 but 2 of them are really long, cant fit them in one post.
Voliminal_8 said:
I already have this tool and used it with the same results.
Which log do you need? It has 3 but 2 of them are really long, cant fit them in one post.
Click to expand...
Click to collapse
did u manage to get the preloader from smartdxxx............. ???????
it just takes 5 minutes (the most) to create the preloader from the phone.
take up the battery from the phone, run sp flash tool, connect the phone to computer, 5 sec, the rom_0 is read
put back battery, on the phone, connect the phone to computer, run mtk droik tool, 30 secs later, the preloader is created.
china phones
stevenma61 said:
did u manage to get the preloader from smartdxxx............. ???????
it just takes 5 minutes (the most) to create the preloader from the phone.
take up the battery from the phone, run sp flash tool, connect the phone to computer, 5 sec, the rom_0 is read
put back battery, on the phone, connect the phone to computer, run mtk droik tool, 30 secs later, the preloader is created.
Click to expand...
Click to collapse
been to a lot off repair phones shop and all stead screen x920 done buy a SquareTrade 2 yr warranty £30.99 ins on phones
Hi folks,
Today it's a great day for me : I have successfully patched the kernel to have a 100% working TWRP 3.2.1 for our Maze Alpha 4G.
I have port a Jemmini build for Bluboo S1 and I have patch the kernel to have a working touch panel
I have followed this Thead
For the Maze Alpha 6G version, you can test it and tell me please.
How to flash:
I Fastboot method (must unlock device) :
1- Reboot your phone in bootloader mode : adb reboot bootloader or phone off, press and hold at the same time POWER and Vol+ buttons
2- Connect your phone to your computer with adb/fastboot already installed
3- Unlock your bootloader : fastboot oem unlock (it will erase you data, only data)
4- Flash the recovery : fastboot flash recovery recovery_maze_alpha_4G_twrp-321.img
II SPFlashTool method (no need to unlock device) :
1- Download latest version of SPFlashTools.
2- Execute it and load the provided scatter (the recovery image must be in the same folder as the scatter and must be renamed to recovery.img) then press "Dowbload" button
3a- windows SPFlashTools users : phone off, press VOL+ and connect it to your PC (running SPFlashTool and waiting for phone connetion)
3b- linux SPFlashTools users : phone off and connected to PC , press VOL+ and POWER while your PC is running SPFlashTool (with sudo) and waiting for phone connetion.
Update : you can found here the latest version: TWRP 3.3.0 for MAze Alpha 4Ghttps://github.com/dreambo/android_device_maze_alpha/releases/tag/3.3.0
have a nice day.
Works great on Maze alpha 4G. Thanks.
But I forgot to save original recovery...
super_sonic said:
Works great on Maze alpha 4G. Thanks.
But I forgot to save original recovery...
Click to expand...
Click to collapse
You can get the original recovery from the stock rom designed for SPFlashTool, provided here
dreambo said:
You can get the original recovery from the stock rom designed for SPFlashTool, provided here
Click to expand...
Click to collapse
Thanks. Can you share stock recovery.img, if you have it? I have recovery-verified.img from V05 but I don't know if there is a new update and if size is correct: 11,54MB. Your TWRP recovery has got a size of 14.24MB...
Can you make a small procedure on how to install it? Will help many nOOb's out.
And people need to report back issues and successes !!!! Again I see many questions and people with issues that we seniors try to help out with that end up in no more response which to me is not done and not helping others.
I have a 6GB version that I could test on but at the moment I am using it for other stuff and I can't risk bricking it this week.
Would finally love to start some stuff happening on this phone.
Ok in the process of doing so on my 6GB/64GB version.
edit : congratz I now have a 'phone' that can only go into TWRP . Should have never ever done this!
Says no OS installed ... really nice
Edit 2: after hours wasted was able to get your zipped rom on the Maze but I got no boot with that TWRP, so flashed recovery-verified.img from the 6GB rom from Alpha I had downloaded ... It would then start up but show 4GB out of 6GB. No good but at least all the rest seemed to work. All other effort to get it going back with the proper kernel etc resulted in frustration.
So now to flash the official rom back via their tool... that one got me really frustrated and was completely my fault that I couldn't figure it out. But you know angry, frustrated, must get it back to work, can do this ... After all these years of toying with phones we are so used to pressing 'power and vol+ or vol-' together to make something work. Now in the end I re-read the manual again and saw that you only have to push vol+ and NOT vol+ and power together or it wont go in the mode it should go to make it flash!!
In case this happens : The best advice I can give to people is to download the proper MTK drivers. Search for vcom drivers for MTK and you will find.
Print out the instructions and mark every step you do to the letter. The flashing itself only takes like 3 or 4 minutes
lukesan said:
Ok in the process of doing so on my 6GB/64GB version.
edit : congratz I now have a 'phone' that can only go into TWRP . Should have never ever done this!
Says no OS installed ... really nice
Edit 2: after hours wasted was able to get your zipped rom on the Maze but I got no boot with that TWRP, so flashed recovery-verified.img from the 6GB rom from Alpha I had downloaded ... It would then start up but show 4GB out of 6GB. No good but at least all the rest seemed to work. All other effort to get it going back with the proper kernel etc resulted in frustration.
So now to flash the official rom back via their tool... that one got me really frustrated and was completely my fault that I couldn't figure it out. But you know angry, frustrated, must get it back to work, can do this ... After all these years of toying with phones we are so used to pressing 'power and vol+ or vol-' together to make something work. Now in the end I re-read the manual again and saw that you only have to push vol+ and NOT vol+ and power together or it wont go in the mode it should go to make it flash!!
In case this happens : The best advice I can give to people is to download the proper MTK drivers. Search for vcom drivers for MTK and you will find.
Print out the instructions and mark every step you do to the letter. The flashing itself only takes like 3 or 4 minutes
Click to expand...
Click to collapse
Haha I did the same exact thing..and managed to get it working after flashing it with the spflash tool but the trick is if you have Windows 10 latest version you won't be able to do this..at least I couldn't because of driver incompatibility so in my case:
1 I installed Windows 7 and installed mtk drivers for spflash tool
2.booted into twrp
2.1 if you can't boot into twrp or it doesn't turn on you can still try this
3.Start sp flash tool and download the zip the one(in case of trouble)that the moderator published
4. Load the scatter file and make sure that all of the files and the scatter are in the same folder.
5.click download and leave it like that
6.plug in your phone in fastboot if you can't try one of the following
6.1 just plug it in turned off and monitor spflash tool status
6.2 plug it in holding volume up key (just volume not power)
6.3 in twrp go to boot and boot into bootloader
And the tool should do the rest
If all else fails check the drivers one more time
After all that if you are feeling adventurous flash twrp one more time and do not factory reset through twrp ! Because that was the problem in my case and after you unlock bootloader boot your phone and go through the setup without setting the password because twrp will be locked.
Good luck.
frumac96 said:
Haha I did the same exact thing..and managed to get it working after flashing it with the spflash tool but the trick is if you have Windows 10 latest version you won't be able to do this..at least I couldn't because of driver incompatibility so in my case:
1 I installed Windows 7 and installed mtk drivers for spflash tool
2.booted into twrp
2.1 if you can't boot into twrp or it doesn't turn on you can still try this
3.Start sp flash tool and download the zip the one(in case of trouble)that the moderator published
4. Load the scatter file and make sure that all of the files and the scatter are in the same folder.
5.click download and leave it like that
6.plug in your phone in fastboot if you can't try one of the following
6.1 just plug it in turned off and monitor spflash tool status
6.2 plug it in holding volume up key (just volume not power)
6.3 in twrp go to boot and boot into bootloader
And the tool should do the rest
If all else fails check the drivers one more time
After all that if you are feeling adventurous flash twrp one more time and do not factory reset through twrp ! Because that was the problem in my case and after you unlock bootloader boot your phone and go through the setup without setting the password because twrp will be locked.
Good luck.
Click to expand...
Click to collapse
Wait a sec., missing a couple of things here.
1) Do you have a 6GB ?
2) In case you have a 6GB did you manage to get it working, rooted and all?
Your point 6) well I flashed mine on the latest 64bit win10 ... but.... if the phone is off and you connect the usb cable my phone tried to boot up either in twrp with no com port. Also booting it in bootloader doesn't make the comport visible so you can't flash.
The only way to make mine visible for the flashtool was to press vol+ and then connect the usb cable.
Btw I am glad someone finally responds and spreads information. A very good post! Your first 'thanks' well deserved!
I wonder where the guys are that I was trying to help. Did they throw their phones away or something? Sharing is caring I thought.
I want to root mine to alter the camera settings and the media xml file. I find it strange that our sensor, which is the same as in my wife's Xiaomi's, takes seriously bad pictures.
lukesan said:
Wait a sec., missing a couple of things here.
1) Do you have a 6GB ?
2) In case you have a 6GB did you manage to get it working, rooted and all?
Your point 6) well I flashed mine on the latest 64bit win10 ... but.... if the phone is off and you connect the usb cable my phone tried to boot up either in twrp with no com port. Also booting it in bootloader doesn't make the comport visible so you can't flash.
The only way to make mine visible for the flashtool was to press vol+ and then connect the usb cable.
Btw I am glad someone finally responds and spreads information. A very good post! Your first 'thanks' well deserved!
I wonder where the guys are that I was trying to help. Did they throw their phones away or something? Sharing is caring I thought.
I want to root mine to alter the camera settings and the media xml file. I find it strange that our sensor, which is the same as in my wife's Xiaomi's, takes seriously bad pictures.
Click to expand...
Click to collapse
Sorry forgot to mention I have a 4 GB version but since maze is not providing the roms on their website any further development will be limited..thank God for dreambo he is the only guy doing any work here and like you said nobody is responding to any questions asked..shame really because maze is a great phone with a terrible camera..which drivers did you use on Windows 10? because I tried a hundred of them and non of them recognize my phone..and in adb I can run the command fastboot reboot bootloader but after reboot none of the commands are working .
And yes I did manage to install twrp and root using magisk and I to hope that all those other guys didn't brick their phones
frumac96 said:
Sorry forgot to mention I have a 4 GB version but since maze is not providing the roms on their website any further development will be limited..thank God for dreambo he is the only guy doing any work here and like you said nobody is responding to any questions asked..shame really because maze is a great phone with a terrible camera..which drivers did you use on Windows 10? because I tried a hundred of them and non of them recognize my phone..and in adb I can run the command fastboot reboot bootloader but after reboot none of the commands are working .
And yes I did manage to install twrp and root using magisk and I to hope that all those other guys didn't brick their phones
Click to expand...
Click to collapse
This is the filename I used on Windows 10 VCOM Drivers (All MTK Devices & All Windows OS version).zip I think I downloaded it from XDA somewhere.
Also something you must know https://www.howtogeek.com/167723/ho...8.1-so-that-you-can-install-unsigned-drivers/
Another thing I experienced is that one USB connector is not the other one on a pc. Always connect it to the ones directly on the main board next to the other device outputs like audio etc. and preferably not go through ones that have been extended via a cable like the ones on top of the casing or so. Also a must have application is usbdeview.
Well should be easy to get it going if you can boot it into 'fastboot' then you can try as much as you want to. But djeeeeezzzz the letters are very small when you boot it with a power+volume up . Also check that volume up will toggle between 'fastboot', 'recovery' and 'normal start' and volume minus will select it, not the power button which would be more logical to me.
I might have another go at trying to get it working on my 6GB but it involves having a lot of time and knowing that I will get frustrated. Installing all apps and settings is also a time consuming thing. Once you have TWRP on it it all becomes easy to backup. So many things to test or try.
Maybe dreambo has an idea on how to get mine up to a 6GB one as it is probably only indicated in the kernel.
Anyway I will continue to write down my progress.
Ok more frustration. Done multiple things to try to get this running. It's good to know that the original rom is easy to install again after practice.
Take 1: Try to install clean 6GB rom and immediately install TWRP.
Results: Dreambo forgot 1 step and that is to allow OEM unlock in the developer options. If you do the adb command to unlock press volume up and it will unlock (very hard to see, very small letters on the display in bootloader mode)
Well TWRP starts but immediately I get a message 'mount decrypt data password' which I tried a couple of things but no go. Also googled... different solutions but always ending in a bootloop to TWRP
A possible solution that I read was to create a startup pin .... no go 'pin not valid'
Take 2: Take all the rom files and change the scatter file with the one dreambo provided.... Thought it was successful but ended up with the same Chinese recovery. Trying to figure out why since the filename was correct like indicated in the scatter file. Came to the conclusion that the original file was/is called recovery-verified.img and not recovery.img. Really really strange this one as in the original scatter file it also points to recovery.img. So this one I will have to investigate. Renaming the TWRP file to recovery-verified.img lead to a error during the initial scan of the flashtool.
So moral of the story is that I am back on square 1 and lost 2 hours today (plus putting all apps and settings back) today.
I get a bit lost, is this TWRP method only working with the 6GB or also with the 4GB version?
CYberdog11 said:
I get a bit lost, is this TWRP method only working with the 6GB or also with the 4GB version?
Click to expand...
Click to collapse
There is no fundamental difference between 6G and 4G version.
It must works in boat versions.
If you have issues with SPFlashTool try this (no need to install any drivers on Windows 10) :
Put the preloader.bin (found in the rom package designed for SPFlashTool) in the same folder as the recovery.img without checking it the list of partitions (only recovery must be checked) and click on Download to flash the recovery, as usual.
Perhaps SPFlashTool cannot read by himself the preloader in the EMMC, and we must provide it.
The linux version of SPFlashTool not works at this moment, I do not know why
With the SPflashtool I always get the error:
ERROR:STATUS_DA_HASH_MISMATCH (0xC0070004)
HINT
CYberdog11 said:
With the SPflashtool I always get the error:
ERROR:STATUS_DA_HASH_MISMATCH (0xC0070004)
HINT
Click to expand...
Click to collapse
From another thread:
mmakdz said:
google translate
Hello
I had the same problem, (error BROM ERROR: STATUS_DA_HASH_MISMATCH)
what I did: I use Windows 7 System
1- clear all drivers for smartphones with "usbdeview-2-17"
2- install Drivers "Drivers_Auto_Installer_v1.1236.00"
3- install "PdaNetA4170"
4- use "SP_Flash_Tool_v5.1708_Win" to flash the rom. first flash the preloader alone and then flash the others.
the problem was the bad installation of the drivers, after that everything went well for me.
try it can work for you too.
the mentioned software is easy to find on google
Click to expand...
Click to collapse
dreambo said:
There is no fundamental difference between 6G and 4G version.
It must works in boat versions.
If you have issues with SPFlashTool try this (no need to install any drivers on Windows 10) :
Put the preloader.bin (found in the rom package designed for SPFlashTool) in the same folder as the recovery.img without checking it the list of partitions (only recovery must be checked) and click on Download to flash the recovery, as usual.
Perhaps SPFlashTool cannot read by himself the preloader in the EMMC, and we must provide it.
The linux version of SPFlashTool not works at this moment, I do not know why
Click to expand...
Click to collapse
If there is no difference between the 4GB and 6GB then why did I literally spend days on trying this and documenting what happened?
lukesan said:
If there is no difference between the 4GB and 6GB then why did I literally spend days on trying this and documenting what happened?
Click to expand...
Click to collapse
Do you have the 2 versions of the phone and do you have notice any difference of the flashing procedure ?
dreambo said:
Do you have the 2 versions of the phone and do you have notice any difference of the flashing procedure ?
Click to expand...
Click to collapse
I only have the 6GB version of the Maze Alpha. But you wrote that the procedure should work for both versions. I think I wrote down what happened with mine if I installed TWRP.
I tried both the 'regular' flashing and then the full rom install with the trick to put the files in the directory and rename but both ended up as I've written in my previous post.
lukesan said:
I only have the 6GB version of the Maze Alpha. But you wrote that the procedure should work for both versions. I think I wrote down what happened with mine if I installed TWRP.
I tried both the 'regular' flashing and then the full rom install with the trick to put the files in the directory and rename but both ended up as I've written in my previous post.
Click to expand...
Click to collapse
From times to times, I notice trouble with flashing using SPFlashTools.
First (when I post my first post relating of the root) I use the linux version : no issues it works perfect, no need of any drivers!
Actually, no way to have it working on linux, why I do not know!
I have tried Windows 10 and I notice that we have to provide the preloader to have it working, as I write in my post.
In theory, and only in theory, the SPFlashTool must works the same manner in any phone with a Mediatek SOC.
But in reality, we have notice that with exactly the same phone the flashing procedure works for some users and not for others!
SPFlashTool is a very capricious software, there is no warranty to have it 100% working in any platform, even with the same OS.
dreambo said:
From times to times, I notice trouble with flashing using SPFlashTools.
First (when I post my first post relating of the root) I use the linux version : no issues it works perfect, no need of any drivers!
Actually, no way to have it working on linux, why I do not know!
I have tried Windows 10 and I notice that we have to provide the preloader to have it working, as I write in my post.
In theory, and only in theory, the SPFlashTool must works the same manner in any phone with a Mediatek SOC.
But in reality, we have notice that with exactly the same phone the flashing procedure works for some users and not for others!
SPFlashTool is a very capricious software, there is no warranty to have it 100% working in any platform, even with the same OS.
Click to expand...
Click to collapse
The thing is that I have no issue with flashing the software as I can perfectly flash the original rom. The problem is that when flashing the TWRP file, in both options by the way, so also via method 1, I get a boot loop.
this phone use mt6739.so i want to flash it the twrp to my phone.i dunno to unlock the bootloader but the twrp file not have for this device.
I just saw this post as I too have a Honor 7S
There is NO TWRP for our device.
The TWRP for the Honor 7A/7C/7X and Honor 7 doesn't work on our device and you got to pay 4 euros to unlock the bootloader before you can even flash TWRP (and there isn't one)
This Device is treble compatible but now I've found out there is zero development and no Devs Interested in it it's a complete and utter waste of time and has gone back into its box, never to be seen again.
hi there, I get this phone recently (because is old) and I created twrp for i,t so here it is, if you want some fun
you can flash it via flashtool on locked bootloader in to boot partition and after that you push twrp.img via adb to internal storage and flash it in to erecovery and recovery slot, and you are good to go
Samuel Ladziansky said:
hi there, I get this phone recently (because is old) and I created twrp for i,t so here it is, if you want some fun
you can flash it via flashtool on locked bootloader in to boot partition and after that you push twrp.img via adb to internal storage and flash it in to erecovery and recovery slot, and you are good to go
Click to expand...
Click to collapse
Hi I have a problem. I'm having brom issues in trying to flash it
Hi
I thinking you dont have "Authentication file" so you using "mtksecurebootdisabler",
so you need patch your drivers with libusb "patch".
Try this one, for me it works.
So open libusb that you install.
connect your honor7s to the pc with disconnected batery and hold volume down.
in patch option select your usb mtk device "idk how is called" and patch it
after patching reconnect phone and it will works.
usab1oy said:
Hi I have a problem. I'm having brom issues in trying to flash it
Click to expand...
Click to collapse
and little hint
dont flash whole rom if the phone can boot becasue after clean flash "format+download"
you lost log and cust partition because the image files are not secureboot signed and your phone get in to bootloop
and also you lost imei codes so no cellular after that
If you do so
you can fix it in that recovery were I enabled option to format log partition
after you format log to ext4, your phone will boot but without huawei/honor bootanimation
you dont need to worry about cust partition, if you didnt format it it still boot but without bootanimation and you lost some of garbage apps that are in that partition (amazon etc...)
(twrp boots in russian language, idk for now how to change it to boot in english or slovak lanuage (because Im from slovakia) and also it have Lenovo Logo becasuse I use sources from Lenovo A5 that have same cpu)
I will make in future separated thread for this....
Thanks alot for this.. I don't know maybe I should try the disconnected battery. But from a yt link I saw
The link : Honor 7s Dua-Al000
I wonder how his worked
I'll have to know how to disconnect the battery thou. I'm a noob at this.
Samuel Ladziansky said:
Hi
I thinking you dont have "Authentication file" so you using "mtksecurebootdisabler",
so you need patch your drivers with libusb "patch".
Try this one, for me it works.
So open libusb that you install.
connect your honor7s to the pc with disconnected batery and hold volume down.
in patch option select your usb mtk device "idk how is called" and patch it
after patching reconnect phone and it will works.
Click to expand...
Click to collapse
Sorry for the noob question but after patching with the battery disconnected. When I want to use spflash tools would I still use disconnect the battery to flash the recovery and co.
usab1oy said:
Sorry for the noob question but after patching with the battery disconnected. When I want to use spflash tools would I still use disconnect the battery to flash the recovery and co.
Click to expand...
Click to collapse
you can patch it or flash it without disconecting the battery
Here is how:
turn it off
Push and hold volume down
While holding volume down connect usb cable
But is recomended to disconect battery because the phone can boot up instead to go in flash mode.
usab1oy said:
Thanks alot for this.. I don't know maybe I should try the disconnected battery. But from a yt link I saw
The link : Honor 7s Dua-Al000
I wonder how his worked
I'll have to know how to disconnect the battery thou. I'm a noob at this.
Click to expand...
Click to collapse
Well he did with the battery and he add more steps that are not necessary for flashing, like scanning for COM port etc...
When I first try flash my 7s I download flashtool and didn't change any settings, I just load the rom and flash it.
So you must try to find your best way how to do and I will help you
And I wonder how he can flash the Log and Cust partition via flashtool, Maybe he have unlocked bootloader or something
Update: he have in the video description link for "lib usb" but didn't show it in video, or I'm just blind or something
Samuel Ladziansky said:
Well he did with the battery and he add more steps that are not necessary for flashing, like scanning for COM port etc...
When I first try flash my 7s I download flashtool and didn't change any settings, I just load the rom and flash it.
So you must try to find your best way how to do and I will help you
And I wonder how he can flash the Log and Cust partition via flashtool, Maybe he have unlocked bootloader or something
Update: he have in the video description link for "lib usb" but didn't show it in video, or I'm just blind or something
Click to expand...
Click to collapse
Yeah. For the flash mode, I wonder why his own he said I need to hold the volume up and down button at the same time. But thanks I'll do it and let you know.
here is version 3 of twrp recovery port
-fixed language form russia to english
-lenovo banner replaced with original TWRP
Samuel Ladziansky said:
here is version 3 of twrp recovery port
-fixed language form russia to english
-lenovo banner replaced with original TWRP
Click to expand...
Click to collapse
At this point. Might just abandon it. Thanks for everything. Ran into laptop issue on my third trial lol.
Yeah I see, drivers issues, it happens to me too, but I install windows 7 and everything works... but I think is not worth it to format your laptop and install win7 only for this mediatek crap, where you can't unlock bootloader or anything because Huawei trying to protect customers and they believe that their android is best for they're phones
Samuel Ladziansky said:
Yeah I see, drivers issues, it happens to me too, but I install windows 7 and everything works... but I think is not worth it to format your laptop and install win7 only for this mediatek crap, where you can't unlock bootloader or anything because Huawei trying to protect customers and they believe that their android is best for they're phones
Click to expand...
Click to collapse
Honestly. I spend a whole night researching videos for the phone. Only to get that link I send. And after all that. It still didn't work. Lol. I have a Poco x3 pro. I wonder if snapdragon android 12 can be rooted. Probably going to try it next month or so.
Snapdragon is eazy for root.
I have Redmi note 11 and it was easy, now I running on Android 13 from stock android 11, if you will need some help with something, I'm here, and I think there is device forum so there is community for that device
Disclaimer: By attempting any of the processes listed in this thread you accept full responsibility for your actions. I will not be held responsible if your device stops working, catches fire, or turns into a hipster and claims to have been modified before it was cool.
Hi everyone, similar to the previous threads for
OP3, OP3T, OP5, OP5T, OP6, OP6T, OP7, OP7PRO, regular OP7T, T-Mobile OP7T, regular OP7TPRO, T-Mobile OP7TPro 5G, regular OP8, T-Mobile OP8 and OP8Pro here are the EDL packages (also known as MSM tools or unbrick tools) that can revive a bricked OnePlus Nord.
You can also rollback your phone to a previous release of OOS with them if for some reason you would like to go back to an older firmware
You can download the following versions:
AC01AA tools (global firmware):
ANDROID 10:
OOS 10.5.2
OOS 10.5.3
OOS 10.5.4
OOS 10.5.5
OOS 10.5.7
OOS 10.5.8
OOS 10.5.9
OOS 10.5.10
OOS 10.5.11
Mirror for first and last MSMs: https://onepluscommunityserver.com/
AC01BA tools (european firmware):
ANDROID 10:
OOS 10.5.2
OOS 10.5.3
OOS 10.5.4
OOS 10.5.7
OOS 10.5.8
OOS 10.5.9
OOS 10.5.10
OOS 10.5.11
Mirror for first and last MSMs: https://onepluscommunityserver.com/
AC01DA tools (indian firmware):
ANDROID 10:
OOS 10.5.2
OOS 10.5.3
OOS 10.5.4
OOS 10.5.7
OOS 10.5.8
OOS 10.5.9
OOS 10.5.10
OOS 10.5.11
Mirror for first and last MSMs: https://onepluscommunityserver.com/
Warning:
As this happened on OnePlus 8 and OnePlus 8 Pro Pro, it is advised to take backup of /persist partition before crossflashing (eg going from European to Indian build) as fingerprint reader may give an error related to enrollment issue. You can do so by using dd if=/dev/block/bootdevice/by-name/persist of=/sdcard/persist.img (you must have root access, see https://forum.xda-developers.com/oneplus-nord/how-to/guide-how-to-root-oneplus-nord-t4139411 for that) and moving it to your computer/cloud.
Instructions:
Launch MsmDownloadTool V4.0.exe.
On the login prompt select "Other" in the dropdown menu and click on Next.
Wait a few seconds until main window shows up.
Click on Target button and select O2 while using global tool or India while using indian tool or EU when using european tool.
Press Start button (this is done so that device will be "captured" automatically by tool instead of going back to normal boot after 10 seconds)
Power your device off.
Let it cool down for one minute.
Maintain volume up and volume down keys for at least 40 seconds to get into Qualcomm EDL mode.
Plug your device to your computer using stock OnePlus cable. (You may let volume keys go once done.)
Wait ~300 seconds.
Enjoy your brand new device.
FAQ:
Does this work on Mac or on Linux?
Unfortunately no, tool is Windows only. You should need at least Windows 7.
Why is my antivirus freaking out when unzipping the archive or running the tool?
In an effort to protect reverse engineering from being done (and by extension prevent conversion process like it was done on 6T and 7Pro), OnePlus now use VM Protect V3 in their MSM tools. As this tries to detect debug environment, this is seen as malicious behaviour by some antivirus.
My device isn't detected
Go to device manager and make sure your phone shows up as QDLOADER 9008.
If it shows up as QHUSB_BULK, it means Qualcomm driver wasn't installed automatically by Windows Update. Download the latest one from Microsoft website at http://download.windowsupdate.com/c..._fba473728483260906ba044af3c063e309e6259d.cab (source https://www.catalog.update.microsoft.com/Search.aspx?q=qualcomm hs usb 9008 ) and install it manually by right clicking on QHUSB_BULK and selecting "Update driver software" and "Browse my computer for driver software" to where you downloaded CAB file.
MSM tool is stuck on "Param pre-processing"
Ensure you're using the Qualcomm drivers linked above.
MSM tool is stuck on "Sahara communication failed"
Unplug your phone, get in fastboot mode, turn off phone, wait 15 secondes and get back in Qualcomm EDL mode. You can also try using a USB 2.0 port instead of a 3.0 one.
What is SMT Download mode?
Just don't try to unlock that mode, it will wipe your IMEI and your Widevine certificate if you use it.
How can I fix "SMT config not found" error?
Please refer to https://forum.xda-developers.com/showpost.php?p=83448961&postcount=61, all credits to @Shadow12347 for finding it out.
Credits:
@Lord Ace for testing 10.5.2 Indian tool on his device.
OnePlus for the device and OS
Related: [OnePlus Nord][ROM][OTA][Oxygen OS] Repo of Oxygen OS Builds
It worked for me,
After unlocking and locking bootloader and ended with corrupted device on locked bootloader
This method helped to solve it.
Thank You
Big thank you!
Thank you very much, just what I'm looking for
Thanks a lot
Good stuff man. Appreciate it!
Does anyone have a persist.img for Global firmware.
I have a different issue which I'd like to try resolve with persist.img
https://forum.xda-developers.com/oneplus-nord/help/nv-backup-warning-t4148599
Big thanks, fixed my semibricked Nord, time to try an GSI again
Small token for the help: Transaction ID: 5NF52401AU895305W
NisseGurra said:
Small token for the help: Transaction ID: 5NF52401AU895305W
Click to expand...
Click to collapse
Thanks for your donation, appreciate
@ Some_Random_Username
I have a NVBackupUI(thread here) error msg that refuses to go away.
I have used your guide to reflash OOS 10.5.2 but the error message is still there.
Do you by any chance have any idea on a way to resolve this?
norder said:
@ Some_Random_Username
I have a NVBackupUI(thread here) error msg that refuses to go away.
I have used your guide to reflash OOS 10.5.2 but the error message is still there.
Do you by any chance have any idea on a way to resolve this?
Click to expand...
Click to collapse
How you got this error..
And is this affecting your phone functionality?
cultofluna said:
How you got this error..
And is this affecting your phone functionality?
Click to expand...
Click to collapse
This is a brand new set and I first noticed it after I set up my phone. The usual data transfers, reinstalling apps etc. But now, it will not go away. Im thinking it's like that out of the box, just that I did not notice it earlier.
So far I have not had any issues functionality wise and my local OP support tells me to ignore it and a future update will fix it. They're not sure of the cause either and could not fix it.
This message keeps coming back even after multiple factory resets + a ROM reflash. I'm trying to rule out a hardware issue.
I did notice that this app is one of those that you remove when you debloat your OP set. I'm sure it would go away if I did that but if theres an underlying issue I might just be setting myself up for a catastrophic failure in future.
Hi, my friend really messed up with his phone. Phone currently have encrypted data partition. Problem is that msmtool doesn't detect phone at all, also device manager doesn't show it while its in msmtool. Anything he can do?
norder said:
This is a brand new set and I first noticed it after I set up my phone. The usual data transfers, reinstalling apps etc. But now, it will not go away. Im thinking it's like that out of the box, just that I did not notice it earlier.
So far I have not had any issues functionality wise and my local OP support tells me to ignore it and a future update will fix it. They're not sure of the cause either and could not fix it.
This message keeps coming back even after multiple factory resets + a ROM reflash. I'm trying to rule out a hardware issue.
I did notice that this app is one of those that you remove when you debloat your OP set. I'm sure it would go away if I did that but if theres an underlying issue I might just be setting myself up for a catastrophic failure in future.
Click to expand...
Click to collapse
norder said:
@ Some_Random_Username
I have a NVBackupUI(thread here) error msg that refuses to go away.
I have used your guide to reflash OOS 10.5.2 but the error message is still there.
Do you by any chance have any idea on a way to resolve this?
Click to expand...
Click to collapse
Unfortunately no idea, MSM tool in upgrade mode doesn't touch to NV items.
Either wait a new OOS build after 10.5.4 or RMA your device.
skayii said:
Hi, my friend really messed up with his phone. Phone currently have encrypted data partition. Problem is that msmtool doesn't detect phone at all, also device manager doesn't show it while its in msmtool. Anything he can do?
Click to expand...
Click to collapse
Make sure his device is off before trying to get in Qualcomm HS-USB 9008 mode, that was something we ran into during testing.
Also as a sidenote encryption state of the phone doesn't matter to use this tool.
Thanks a lot for the unbrick tool!
Some_Random_Username said:
Unfortunately no idea, MSM tool in upgrade mode doesn't touch to NV items.
Either wait a new OOS build after 10.5.4 or RMA your device.
Click to expand...
Click to collapse
Understood. Thank you
Works great thanks a lot for the links i had to install the driver and your post was well made to avoid me any hassles
By the way, it re-locks the bootloader
@ Some_Random_Username
can you tell me how you got this tool?
i could try getting the tool with oxygen os 10.55
thanks for this.