Related
Hello all,
My Umi z charger cable has broken. Tried charging with One plus 3T charger but it doesn't work.
Anybody can recommend what charger cable shall work and where it shall be available?
I have no problem charging with any mix if cable and charger ..even standard USB chargers with adaptor to c fitting
Any decent USB A to USB C cable should work.
Use Nexus's usb cable
I have a Nexus 6P and I use the tiny cable they gave with the phone to charge Z pro with my laptop.
It charges pretty quickly with that cable on my laptop. But yea any decent cable would do. You can also order chargers on Umi's website.
I use this cable...
https://www.amazon.de/gp/product/B01MY27YKY/ref=oh_aui_detailpage_o09_s01?ie=UTF8&psc=1
In principle, however, every cable should be suitable.
Make sure it is suitable for data transfer and loading.
Some cables have too much resistance, and then the charging time increases.
Hello,
I have found this comment about the cable :
Note: I tested PC mode with a USB Type-C to HDMI cable I bought on Amazon. Because the Mate 10 and Mate 10 Pro support USB 3.1 it’s technically possible that you can screen share to a monitor and charge the device at the same time. I asked Anker if a powered USB hub with HDMI support like this would work, but they said it depends on wiring and whether a hub has been designed to communicate with the Mate 10 or not. I also asked Huawei for clarification, and they have vowed to get back to me on the specifics of what to look out for in a compatible hub. I’ll update the review as more information comes in. Thanks to Bram Peeters for raising this issue.
Source : https://www.androidauthority.com/huawei-mate-10-pro-review-807465/
Is there a HUAWEI reference for this cable ?
Does it need to be HDCP compatible, with Netflix eg ?
Best regards
Hi Pascal... I already tried the desktop mode. Technically any type-c to hdmi adapter should work. I'm using this: https://www.incipio.com/chargers/usb-c/usb-c-digital-av-multiport-adapter.html ... and I added an HDMI to VGA cable adapter because there's a VGA cabled monitor at home that's not in use.
My current setup:
** Mate 10
** Incipio 3-port AV adapter
++ Logitech 2 in 1 wireless combo (keyboard and mouse using 1 usb dongle) attached to the 3-port adapter
++ Charger attached to the type-c port
** HDMI to VGA adapter
** monitor
Works without any issues except that the charger cannot push enough power to actually charge the phone. It still drops so probably from 80% you have a good 2 hours average of desktop mode time to perform stuff. I am thinking of getting a DELL type-c to hdmi adapter (just a simple hdmi adapter no extra ports) for playing games.
I got myself a Macbook usb 3.1 dongle ( Lmao ) and i can't seem to push power fast enough to charge my phone, it helps though, having power in drains the battery slower than having no power in
404ErrorUsernameNotFound said:
I got myself a Macbook usb 3.1 dongle ( Lmao ) and i can't seem to push power fast enough to charge my phone, it helps though, having power in drains the battery slower than having no power in
Click to expand...
Click to collapse
In fact, few months ago, i was looking for a USB C HUB (With or not HDMI, Ethernet) with power delivery,
for an ACER SWITCH V10 (2017), to connect many external USB HDD and KEYS.
I have found many products on Amazon.
And these products (USB C HUB) like EgoIggo HUB USB C (GN30E) on Amazon, could be fully adapted
with a Mate 10 PRO. Some of them are too Mac OS X or/and Windows compatible, with or not drivers.
Look the description :
[Multi-operation] 3 USB 3.0 ports, 2 Card Readers for SD and micro SD, 1 HDMI Slot, 1 RJ45 Eternet Port and 1 USB Type-C Charging Port. Compatible with new devices equipped with a Type-C USB port.
[High transfer speed] With a data rate of up to 5 Gbps, the three USB 3.0 ports allow you to connect your keyboard, mouse, USB flash drive and external hard drive to the laptop. An SD player and a micro SD player support SD / SDHC / SDXC cards up to 2 TB. An HDMI slot that supports resolutions up to 4K. An RJ45 Ethernet port allows a super-fast internet network up to 1Gbits / s, but also backwards compatible with 10 / 100Mbps
[Unique Design] This Hub is very small and thin, but robust, whose connection cable is properly flexible, which makes the connection very stable. This elegant aluminum-shaped design perfectly matches the style and color of MackBook and MackBook Pro.
[Power Delivery] USB-C Power Delivery (PD) for Macbook Macmini and other USB-C devices, capable of simultaneously transferring data and charging devices.
[Ultra Portable] This hub is packed with a small box of cardboard and well protected by a nice cover that prevents it from scratching your mackbook. Incredibly compact size and very practical to carry everywhere.
Best regards
404ErrorUsernameNotFound said:
I got myself a Macbook usb 3.1 dongle ( Lmao ) and i can't seem to push power fast enough to charge my phone, it helps though, having power in drains the battery slower than having no power in
Click to expand...
Click to collapse
same concern with the incipio that I'm currently using.
From what I see, it will just drain the battery however we use it. Probably faster if we use the same adapter as Pascal's find. If I have the chance I will test Huawei's adapters (they have a different brand of adapter here in the Philippines) - I can try and borrow: see if it CAN push the power enough to charge the phone. But I'm already assuming that it won't.
Given the fact that the type-c port provides 100% of what it's supposed to run on desktop mode, powering the adapter.. powering whatever usb device is plugged in, that power requirement is the one that needs to be addressed.
But overall not bad for a phone especially when you can still use the phone while working on desktop mode. We can't do work on the phone of course but just enough to get a few things done with a screen and keyboard/mouse combo...
Well according to some German website it's stated that the Mate 10 is Compatible with USB [email protected]*2A so we might need to get a USB PD compatible charger to hopefully gain more juice than using draining the battery slowly
404ErrorUsernameNotFound said:
Well according to some German website it's stated that the Mate 10 is Compatible with USB [email protected]*2A so we might need to get a USB PD compatible charger to hopefully gain more juice than using draining the battery slowly
Click to expand...
Click to collapse
probably if we use an adapter with a type-c slot going to the type-c port of the hdmi/type-c adapter....
I was looking at the Tronsmart multiport charger I think. It has a type-c port so you can use a type-c to type-c cable... BUT it only pushes out as fast charge on the mate 9... so of course that's also a fast charge on the mate 10... BUT again, that's if we plug the phone directly to the charger... would that be a different case if we plug it to the hdmi adapter? I'm actually planning to buy it.. just so I have a multiport adapter especially when out and about. This one says Power Delivery.. probably I'll grab this thing by end of the month and the type-c end to end cable...
http://www.tronsmart.com/products/tronsmart-u5p-60w-usb-pd-desktop-charger-with-voltiq
hopefully I can report back as soon as I get it.
current dilemma is we have a super charge adapter... and yet it's not pushing enough juice... hopefully the type-c type-c scenario works so we won't have draining issues...
***** UPDATE *****
CORRECTION ON THE BRAND...
I was referring to Anker and yes the idea for Power Delivery appears to work.
https://www.anker.com/products/variant/PowerPort%2B-5-Ports-USB-C-/A2053111
Still using my desktop mode original setup:
Mate 10 - Incipio 3-port adapter (type-c/hdmi/regular usb) - hdmi to vga adapter (vga cable LED monitor) - TYPE-C to TYPE-C cable going to the new Anker desktop charger (type-c port is Power Delivery capable) ....
Phone shows FAST CHARGING instead of just charging...
https://imgur.com/a/V7qII
Started around 68% now I'm at 74%. So I guess that should be the solution. Just grab a PD (power delivery) capable charger. The one from Tronsmart should work without issues as well.
Cheers guys!:good:
Baseus O HUB Type-C multi-function converter Adapter
Hi, I'm using a mate 10 and I've just bought a Baseus O HUB Type-C multi-function converter Adapter (HDMI + Type-c charging port + USB3.0). Can't seems to get it to work (PC mode or mirror) when connected to HDMI (tried on Panasonic LED TV & Toshiba projector).
Wireless mouse and keyboard working and phone is charging when I've plug in the charger to the hub. Is there any setting that I've missed?
Regarding Desktop mode: I bought an adapter and successfully connected my mate 10 to an HD TV, but the resolution is low, does it depend on the TV, the cable, the adapter or there is a way to set the desktop mode resolution? I haven't found it ...
drkprd said:
CORRECTION ON THE BRAND...
I was referring to Anker and yes the idea for Power Delivery appears to work.
https://www.anker.com/products/variant/PowerPort%2B-5-Ports-USB-C-/A2053111
Still using my desktop mode original setup:
Mate 10 - Incipio 3-port adapter (type-c/hdmi/regular usb) - hdmi to vga adapter (vga cable LED monitor) - TYPE-C to TYPE-C cable going to the new Anker desktop charger (type-c port is Power Delivery capable) ....
Phone shows FAST CHARGING instead of just charging...
https://imgur.com/a/V7qII
Started around 68% now I'm at 74%. So I guess that should be the solution. Just grab a PD (power delivery) capable charger. The one from Tronsmart should work without issues as well.
Cheers guys!:good:
Click to expand...
Click to collapse
so standard Mate 10 Pro charger (which says fast charging when plugged into phone) doesnt fast charge the phone when connected to the USB Hub. But youre saying if i buy this Anker charger my phone will fast charge when connected to a USB hub?
What is the exact spec of that Anker charger that makes it different to the Huawei charger in the box? Sorry for confusion, thanks in advance.
pixielott46 said:
so standard Mate 10 Pro charger (which says fast charging when plugged into phone) doesnt fast charge the phone when connected to the USB Hub. But youre saying if i buy this Anker charger my phone will fast charge when connected to a USB hub?
What is the exact spec of that Anker charger that makes it different to the Huawei charger in the box? Sorry for confusion, thanks in advance.
Click to expand...
Click to collapse
Anker desktop charger that I'm using: https://www.anker.com/products/variant/PowerPort%2B-5-Ports-USB-C-/A2053111
It has Power Delivery - which powers most usb-c devices nowadays especially Macs and other Google devices if I got that correct.
The description has this:
USB Type-C, Premium 5-Port 60W USB Wall Charger with Power Delivery for Apple MacBook, Nexus 5X / 6P and PowerIQ for iPhone, iPad, Samsung & More
The stock charger will definitely work without problems IF DIRECTLY attached to the phone but this time we have an external device - the multi-port hdmi/type-c/usb adapter. Yes it has a type-c port included and you can attach the stock charger but from my experience especially with the Incipio adapter, it requires more "push" because the stock charger just slows down the drain when using desktop mode. It does not increase the phone's battery juice while in use.
:angel:
** Also, Huawei stock supercharger adapter pushes 22.5W of power BUT ONLY if connected directly to phone. Power delivery pushes 29W of power REGARDLESS of which device it's connected to. The Huawei charger is also picky so it might not be using all 22.5W if connected to an in-between adapter.
drkprd said:
Anker desktop charger that I'm using: https://www.anker.com/products/variant/PowerPort%2B-5-Ports-USB-C-/A2053111
It has Power Delivery - which powers most usb-c devices nowadays especially Macs and other Google devices if I got that correct.
The description has this:
USB Type-C, Premium 5-Port 60W USB Wall Charger with Power Delivery for Apple MacBook, Nexus 5X / 6P and PowerIQ for iPhone, iPad, Samsung & More
The stock charger will definitely work without problems IF DIRECTLY attached to the phone but this time we have an external device - the multi-port hdmi/type-c/usb adapter. Yes it has a type-c port included and you can attach the stock charger but from my experience especially with the Incipio adapter, it requires more "push" because the stock charger just slows down the drain when using desktop mode. It does not increase the phone's battery juice while in use.
:angel:
** Also, Huawei stock supercharger adapter pushes 22.5W of power BUT ONLY if connected directly to phone. Power delivery pushes 29W of power REGARDLESS of which device it's connected to. The Huawei charger is also picky so it might not be using all 22.5W if connected to an in-between adapter.
Click to expand...
Click to collapse
hi, thanks for your detailed reply. the edit with the wattage is especially useful. one last question. Does the Anker charger "fast-charge" the huawei mate 10 pro when connected directly? or just standard usb charging?
If yes, i will replace my huawei official charger with this anker one. handy that it has some usb ports as well so i can charge my bicycle lights overnight etc as well
thanks in advance for the further information
pixielott46 said:
hi, thanks for your detailed reply. the edit with the wattage is especially useful. one last question. Does the Anker charger "fast-charge" the huawei mate 10 pro when connected directly? or just standard usb charging?
If yes, i will replace my huawei official charger with this anker one. handy that it has some usb ports as well so i can charge my bicycle lights overnight etc as well
thanks in advance for the further information
Click to expand...
Click to collapse
that's one of the things I actually was surprised with and didn't really expect...really good news for us because it does!! The phone registers FAST CHARGING even if I have "everything" connected for desktop mode.
* phone + incipio type-c hdmi usb combo
* incipio + hdmi-vga converter
* vga converter + vga led monitor
* Anker multi-port with type-c power delivery + anker type-c to type-c cord ..... connected to the incipio
** and a recent addition: since the incipio only has 1 regular USB port, I bought a 4-port usb hub... connected it to the incipio so that basically splits 1 into 4 usb ports... I attached my wireless keyboard/mouse combo and my Western Digital 1 Terabyte external HDD...... NO PROBLEMS WHATSOEVER.... haha!.. phone still chargers UP with fast charging indication...
Now I guess I have a full working desktop system with the mate 10
(I'm using the regular mate 10 but I guess that shouldn't affect the charge input/output)
drkprd said:
that's one of the things I actually was surprised with and didn't really expect...really good news for us because it does!! The phone registers FAST CHARGING even if I have "everything" connected for desktop mode.
* phone + incipio type-c hdmi usb combo
* incipio + hdmi-vga converter
* vga converter + vga led monitor
* Anker multi-port with type-c power delivery + anker type-c to type-c cord ..... connected to the incipio
** and a recent addition: since the incipio only has 1 regular USB port, I bought a 4-port usb hub... connected it to the incipio so that basically splits 1 into 4 usb ports... I attached my wireless keyboard/mouse combo and my Western Digital 1 Terabyte external HDD...... NO PROBLEMS WHATSOEVER.... haha!.. phone still chargers UP with fast charging indication...
Now I guess I have a full working desktop system with the mate 10
(I'm using the regular mate 10 but I guess that shouldn't affect the charge input/output)
Click to expand...
Click to collapse
Just an FYI to others, the Huawei Mate 10 Pro has 3 different charging modes. One is USB Charging, very very slow. One is Fast charging, like regular charging i guess. SuperCharging is really really fast. This Anker charger only fast charges my device.
I cant get SuperCharge unless I use the Huawei official charger or the Huawei AP09S PowerBank.
How can I SuperCharge with 3rd party accessories?!
pixielott46 said:
Just an FYI to others, the Huawei Mate 10 Pro has 3 different charging modes. One is USB Charging, very very slow. One is Fast charging, like regular charging i guess. SuperCharging is really really fast. This Anker charger only fast charges my device.
I cant get SuperCharge unless I use the Huawei official charger or the Huawei AP09S PowerBank.
How can I SuperCharge with 3rd party accessories?!
Click to expand...
Click to collapse
To understand the chargin technologies one must understand how Watts Volts and Ampere work. Volt x Ampere = Watt. Explaining Volt and Ampere is kinda long story but to keep it short: Imagine a garden hose: The pressure of the water is Volt, the speed of the water is Ampere. Watt is the amount of water thats pouring out.
There are various technologies for charging, in the end it matter how many Watts there are. But different combinations of Volts and Ampere are possible to achieve the same amount of Watts.
There is a new universal standard called Power Delivery which was introduced with USB 3.1 Type C. So this is a standard that comes with usb 3.1 type c and that is why all the new usb3.1 type c laptops support it. (PD supports multiple protocols (combinations of V and A to reach up to 100W) and the more powerful ones mostly support the lower ones too. that means a 100W PD charging brick could charge a 5Vx3A=15W Phone, a 14Vx2A=28W iPad Pro, a 60W Macbook, an 80W Ultrabook etc.)
Previous Charging standards are something around 5V and 1A,2A, computer usb 2.0 ports only give 0.5A and usb3.0 ports give 1A, which is why some laptops have a dedicated phone charging port that delivers 2A (most phones used 5V/2A before fast charging technologies hit the market, it is also the protocol phones fall back to if the charging brick does not support the fast charging technology of the phones manufacturer)
Phone manufacturers have their own technoligies or license them from other companies. Qualcom has QuickCharge which many smartphones use (Samsung uses QuickCharge 2.0 with 9V and 1,67A (Delivers roughly 15W))
Huawei has its own SuperCharge which is based on 5V/4A and 4,5V/5A (delivers around 22W). So in order to use supercharge you have to get a charging brick that explicitely supports 4,5V/5A protocol and a cable that supports 5A (since standard USB 3.1 Type C Power Delivery protocols are based on a maximum of 3A most usb-c cables dont support 5A).
So as i mentioned before: more powerful charging bricks usually support less powerful protocols. so in order to charge devices that do not support the specific fast chargind protocol, all chargers also support 5V2A. Thats what happens if a Samsung is charged with huawei brick or my mate 10 pro is charged with the samsung brick (the difference being that Huawei seems to label the usb 3.0 pc port 5V/1A as "charging", the normal 5V/2A as fast charging and the Huawei SuperCharge at 4,5V/5A obviously is called SuperCharge). USB Power Delivery aims to end that by providing a standard that is available for all that use a 3.1 type c port. (that means if i have a 60W apple chargin brick for my macbook i can also use the same brick to charge my 29W ipad pro or another 60W usb type c ultrabook with windows with the same brick and cable without thinking twice. before usb type c and PD all laptops had to have dedicated chargers)
enricomemo said:
Regarding Desktop mode: I bought an adapter and successfully connected my mate 10 to an HD TV, but the resolution is low, does it depend on the TV, the cable, the adapter or there is a way to set the desktop mode resolution? I haven't found it ...
Click to expand...
Click to collapse
Hi enrico. I have exactly the same issue and it seems like its related to the 4K TV only. FHD TV work fine with my mate 10 pro but when I connect it to 4K TV it sticks to 640*480 resolution, which is useless obviously. Have you found a solution or anyone else ?
Karl212 said:
Hi enrico. I have exactly the same issue and it seems like its related to the 4K TV only. FHD TV work fine with my mate 10 pro but when I connect it to 4K TV it sticks to 640*480 resolution, which is useless obviously. Have you found a solution or anyone else ?
Click to expand...
Click to collapse
My TV isn't 4k and I too get the 640*480 resolution
Connorsdad said:
My TV isn't 4k and I too get the 640*480 resolution
Click to expand...
Click to collapse
What is the model of your TV ? Maybe its a model-related issue (not the native resolution), I tried with a hdmi 2.0 cable and the problem is still here. I own a samsung 55MU7000.
drkprd said:
CORRECTION ON THE BRAND...
I was referring to Anker and yes the idea for Power Delivery appears to work.
https://www.anker.com/products/variant/PowerPort+-5-Ports-USB-C-/A2053111
Still using my desktop mode original setup:
Mate 10 - Incipio 3-port adapter (type-c/hdmi/regular usb) - hdmi to vga adapter (vga cable LED monitor) - TYPE-C to TYPE-C cable going to the new Anker desktop charger (type-c port is Power Delivery capable) ....
Phone shows FAST CHARGING instead of just charging...
https://imgur.com/a/V7qII
Started around 68% now I'm at 74%. So I guess that should be the solution. Just grab a PD (power delivery) capable charger. The one from Tronsmart should work without issues as well.
Cheers guys!:good:
Click to expand...
Click to collapse
You getting much heat on the device I've used Samsung dex before and the S8 got warm but not very, I'm using the Mate 10 and the Dex hub which charges fast but phones gets quite hot using easy projection
So I have the stock charger, a rather generic charge cable, a generic hdmi cable, and an Insignia NS-PU378CHM Usb-c to three port HDMI /USB 3.0 /USB-C power
The problem: when I hook up hdmi and am running DeX on my TV, the battery drains. Even with external power connected.
So I measure the current the charger is delivering, and when using the hdmi adaptor, I'm getting about 1/2 an amp. When I plug power in directly to the tablet, I get a full amp. Battery drains faster than it charges when using the adapter.
I don't know if I need a better charger, to suuply more current under load, a better hdmi adapter / power adapter, a better power cable (but the fact the cable supplies twice the current when plugged in directly suggests it isn't the cable).
Does anyone have a combo they use that keeps power from draining when running dex on hdmi?
Or should I figure it is impossible to supply enough current to keep the battery charged at 100% when running hdmi / dex?
Thanks,
Joe
drjoe1 said:
So I have the stock charger, a rather generic charge cable, a generic hdmi cable, and an Insignia NS-PU378CHM Usb-c to three port HDMI /USB 3.0 /USB-C power
The problem: when I hook up hdmi and am running DeX on my TV, the battery drains. Even with external power connected.
So I measure the current the charger is delivering, and when using the hdmi adaptor, I'm getting about 1/2 an amp. When I plug power in directly to the tablet, I get a full amp. Battery drains faster than it charges when using the adapter.
I don't know if I need a better charger, to suuply more current under load, a better hdmi adapter / power adapter, a better power cable (but the fact the cable supplies twice the current when plugged in directly suggests it isn't the cable).
Does anyone have a combo they use that keeps power from draining when running dex on hdmi?
Or should I figure it is impossible to supply enough current to keep the battery charged at 100% when running hdmi / dex?
Thanks,
Joe
Click to expand...
Click to collapse
Check out this link https://forum.xda-developers.com/ga...-usb-c-hub-t3917848/post79289417#post79289417 This should supply enough power while using Dex via HDMI!
I'm recopying this from the Galaxy 9 thread referenced above in the hope someone here has tried this adaptor...
This thread is pretty old, but I'm finally looking at upgrading and have some questions about the Ugreen UCB C / USB 3.1 + HDMI Adaptor.
I'm looking at the USB C - 5 Port Adaptor here:
https://www.amazon.com/UGREEN-Adapte.../dp/B077FZQS95
In the notes it says that
USB C PD fast charging is only for laptops but not for phones. Phones only support normal charging.
Do NOT recommend you charge phone through USB 3.0 port as USB port only can only offer max 1.5A current and will charge your phone slowly
So I'm trying to figure out, is this like a powered USB hub that needs a PD brick to power the hub and then the hub powers the tabled (with 1.5A max), and separately powers the HDMI adaptor, UCB 3.1 devices etc., or is this a power-pass through that powers the tablet (slow) and then the tablet powers the USB devices?
In other words, is there an advantage to buying a $20-30 PD wall brick to power this hub, which the tablet doesn't support, or am I as good as I'm going to get with the original Samsung Lightning charger that came with the tablet?
Thanks,
Joe
I bought one of the U-Green hubs rated for 100W PD:
https://www.amazon.com/gp/product/B07RW343WG/
This one has two USB 3.0 ports, a USB C charger-in port, HDMI, and two card readers, one full size SD, one micro-sd.
Because all of the documentation specifies it uses power delivery type chargers, I was worried it would have problems with a Samsung lightning charger. No problems. With the original lightning charger, the tablet recharges to and holds at 100% even when loaded by hdmi, an external hard drive, a USB thumb drive, and a micro sd card. The simpler / cheaper hub I bought when I got the tablet discharges when hdmi + the same charger is plugged in.
The reviews complained it gets hot enough to burn your finger when touched, but I haven't noticed this at all. This could be a function of the total power delivered to the hub I believe the lightning charger is only 15W. The hub is rated at 100W with PD cgarger. So only a fraction of the power is transmitted through the hub when charging with Samsung lightning charger. It seems most of the 100W is used to charge a PD laptop or Apple device, not the peripherals.
The one change I'd make to it, is that I'd like to have a spring loaded recessed slot for the micro sd card reader. In this hub, it is pushed in / pulled out of the slot leaving ~ 1/4 inch sticking out from the body of the reader when the micro sd card is loaded. If you leave the card in all the time (to use as an external hard drive) there will be a danger of the card snapping. A minor quibble.
I'm happy that it allows the tablet to maintain 100% charge while running hdmi.
Joe
I have been trying a couple of multiport adapters (USB-C, USB-A, HDMI) but while USB-A and HDMI seem to work fine, the charging port seems to do nothing. The tablet does not indicate it is being charged, and when connected to a PC there is no data connection.
There is a suspicious remark in the documentation:
Operation
• Connect the plug to a USB-CTM port on your computer.
...
At the time this manual was written, Android smartphones were not supported.
Click to expand...
Click to collapse
So is it possible that this adapter is not supported by our Tab S4? I would be surprised since I read here that other adapters do work.
For completeness, it is a Renkforce USB C naar HDMI + USB 3.0 Multiport-adapter.
sciurius said:
I have been trying a couple of multiport adapters (USB-C, USB-A, HDMI) but while USB-A and HDMI seem to work fine, the charging port seems to do nothing. The tablet does not indicate it is being charged, and when connected to a PC there is no data connection.
There is a suspicious remark in the documentation:
So is it possible that this adapter is not supported by our Tab S4? I would be surprised since I read here that other adapters do work.
For completeness, it is a Renkforce USB C naar HDMI + USB 3.0 Multiport-adapter.
Click to expand...
Click to collapse
Your description is confusing to me, and I had to translate the product description of your adaptor from Dutch to English, but...
Plug the USB C male connector from the adaptor into your tablet. Your adaptor has three ports:
1) USB 3.0 female - connect to a USB device such as a mouse, keyboard, thumb drive, etc. I'm not sure if you can connect this port to a PC or not.
2) HDMI female - hook to a display
3) USB C female - power input port only. Does not carry data. Does not connect to a PC. Plug your power supply into this port using the same cable that you charge your tablet with.. The charging icon should activate. Your tablet should stay charged while using the other ports, or at least discharge more slowly.
It sounds like you are trying to plug the charging port into a PC. Doesn't work as far as I know.
Thanks for the reply. This is what I do:
1. Plug the USB-C cable from the adapter into the tablet C port.
2. Plug HDMI cable (connected to a monitor) into the adapter HDMI port. This is detected, Samsung Dex starts, and the monitor displays the Dex desktop.
3. Plug keyboard/mouse into the USB-A port of the adapter. This is picked up by the tablet and I can use the keyboard/mouse.
Alternatively, when I plug a USB stick into the USB-A port of the adapter, the tablet shows a new USB storage device.
So far, so good.
4. I connect the Samsung power supply to the USB-C port of the adapter. Nothing happens. The tablet does not start charging (or discharging less). I tried different power supplies and cables, makes no difference.
When I connect the power supply with the same cable to the tablet it charges normally. When I connect the tablet using this cable to a PC hub the tablet also start charging, albeit slowy.
So as far as I can see I did nothing wrong. What suprises me most is that almost everything works fine, except charging.
I've ordered a new adapter (different brand) to see if this makes a difference.
I think it should work... I have a couple adaptors similar to yours and they all work. Particularly Insignia NS-PU378CHM I referenced above.
I do think that adaptors that say they support power delivery (PD) work better than cheaper generic adaptors. Even though the Tab S4 doesn't support
PD itself. I strongly recommend the Ugreen adaptor above.
Good luck,
Joe
I would have bought the Ugreen immedeately if they were easily available in this part of the world. Buying from Amazon is expensive and delivery is slow.
I got myself another multiport hub, brand A-Konic, and this time all three ports seem to work correctly. USB-C charging. USB-A OTG and HDMI. However, Samsung Dex on the monitor is only 1280x720 (on the S4 it is 2560x1600; the monitor is 1920x1080). Not sure if this is related to the hub.
I'm glad you found something that works. I don't know about screen resolutions. There are other threads that discuss HDMI resolution. I think the HDMI cable can make a big difference.
Take care,
Joe
drjoe1 said:
I think the HDMI cable can make a big difference.
Click to expand...
Click to collapse
Initially I got a distorted image on the screen but replacing the high quality cable by an even higher quality cable fixed that.
I'll check out the resolution info.
Samsung Galaxy Tab S4 working 100w adaptor ?
Hello I have the following question to all owners of samsung galaxy tab s4. I have a desire to buy the following docking stantion for my tablet. I have a question if it will work correctly.
USB C Hub, USB C Docking Station, QGeeM 12 in 1 Triple Display Type C Hub to Dual 4K HDMI & DP,USB C to USB Adapter,100W PD, Gigabit Ethernet, USB C Card Reader,USB Docking Station
Samsung Galaxy Tab S4 does it support thunderbolt ?
Will work seamlessly with a 100w adapter?
It will work but it won't use all its capacity. The tablet only can charge at 18w.
I am having good luck with the AUKEY 5-in-1 USB-C Hub, here is the AMZN link:
https://www.amazon.com/gp/product/B089M7WSHM/
It will give screen mirroring to TV. I have used it on both a 720p and a UHD (2160x3840) TV.
It can charge through the hub and use HDMI out and ethernet on the S4. I just wish it wouldn't try to make me setup DEX everytime I plug it in.
Hi everyone, I'm thinking about buying an Anker Powerline+ USB-C to USB-A 3.0 but I'm not sure if it will work with my device. Has anyone tried that cable?
P.S: The official USB-C cable for the HTC U11 is not available in my country.
coderch123 said:
Hi everyone, I'm thinking about buying an Anker Powerline+ USB-C to USB-A 3.0 but I'm not sure if it will work with my device. Has anyone tried that cable?
P.S: The official USB-C cable for the HTC U11 is not available in my country.
Click to expand...
Click to collapse
You can pretty much use any usb c cable
Sent from my HTC U11 using Tapatalk
Thank you. Maybe I have a faulty USB port because a bought a cheap USB-C cable and it doesn't work, it just shows "slow charging" and it takes up to 5 hours to reach 100% also when I connect it to my PC it shows a message that the device could not be recognized.
coderch123 said:
Thank you. Maybe I have a faulty USB port because a bought a cheap USB-C cable and it doesn't work, it just shows "slow charging" and it takes up to 5 hours to reach 100% also when I connect it to my PC it shows a message that the device could not be recognized.
Click to expand...
Click to collapse
Check your power block? If you use a QC compatible block and cable it should fast charge. Try the anker cable
Sent from my HTC U11 using Tapatalk
I bought a Quick Charge 3.0 and a USB-C 3.0 and it works perfect. All the problem was related to the cheap cable I bought before.
This is the 100W Baseus deskop charger and I have two issues with it:
1. When two USB C ports are used, the power division is C1=65W and C2=30W. So C1 should still be more than capable enough to handle SFC 2.0 45W charging. But as you can see in the video, SFC 2.0 is not working when two USB C ports are used.
2. When I charge at SFC 2.0 and SFC 1.0 with the same charger, they both cap at 33W. I thought SFC 1.0 is just 25W? When I use the official 25W Samsung SFC 1.0 charger, it just caps off at 24W as expected.
Baseus support sucks big time so I'm having a problem reporting this to them.
kevindd992002 said:
This is the 100W Baseus deskop charger and I have two issues with it:
1. When two USB C ports are used, the power division is C1=65W and C2=30W. So C1 should still be more than capable enough to handle SFC 2.0 45W charging. But as you can see in the video, SFC 2.0 is not working when two USB C ports are used.
2. When I charge at SFC 2.0 and SFC 1.0 with the same charger, they both cap at 33W. I thought SFC 1.0 is just 25W? When I use the official 25W Samsung SFC 1.0 charger, it just caps off at 24W as expected.
Baseus support sucks big time so I'm having a problem reporting this to them.
Click to expand...
Click to collapse
Baseus GaN5 Pro 65 watt can charge at 50watt peak.
after 60 percent,watt same as samsung 25 watt charger.
But your measurement is input power to the charger and not output power to the phone. There's a bit of a difference because of power adapter efficiency. I don't know what is the difference between the Gan5 Pro 65W and this 100W adapter really.
BUMP! Anyone please?
This is normal for such a charger. I have a PZOZ version - 65W GaN 2xUSB C + 1xUSB A. SFC 2.0 works only with 1 device plugged in, if you plug another (it might be a 5W one) - this breaks the SFC. I can assume that this is coming from the controller and the device is actually not capable to support such scenario, even though the power is declared as 100W.
Hmmm, that's interesting. I thought the issue was isolated to BaseUS. Their support is really non-existent. They reply but it's like you're talking to a stupid person that does not understand the issue.
Aside from this issue, do you have any other issues when using both ports? As for me, when I charge my phone while my laptop is plugged in, it sometimes drops the wattage on the laptop device to just 19w. If the laptop is plugged in by itself, it goes up to 59w. Not sure what's going on here.
Are there any usb c car chargers that support sfc 2.0?
kevindd992002 said:
Hmmm, that's interesting. I thought the issue was isolated to BaseUS. Their support is really non-existent. They reply but it's like you're talking to a stupid person that does not understand the issue.
Aside from this issue, do you have any other issues when using both ports? As for me, when I charge my phone while my laptop is plugged in, it sometimes drops the wattage on the laptop device to just 19w. If the laptop is plugged in by itself, it goes up to 59w. Not sure what's going on here.
Are there any usb c car chargers that support sfc 2.0?
Click to expand...
Click to collapse

Satechi - USB / USB C car charger with 72W:
Simultaneous Charging: Has both a universal USB A port and a Type-C port
Quick Charge: Devices can be charged quickly on the go
Powerful and compact design: Type-C power 60W (max), Type-A power 12W (max), total 72W
Equipped with an LED indicator to check the charging status
With Power Delivery for particularly fast charging
Compatible with almost all USB devices and most USB Type-C devices
The Satechi USB C and USB A Car Charger is the perfect solution for charging your devices on the go. Never worry about how to charge your smartphone, tablet, computer or other device while on the go. Simply connect the charger to your car's cigarette lighter and connect the other end of the USB cable to the USB port of the desired device. You can already charge your device on the go. Satechi's Dual Car Charger allows you to simultaneously charge a 13" MacBook Pro (2016) via the USB-C port and an iPhone/tablet via the USB-A port. The output power for the USB-C port is 60 W (max) and 12 W for the USB-A port.
ATTENTION: The delivery does not include a USB cable!
Color: white/silver
Brand: Satechi
Model: ST-TCPDCCS
Weight: about 34g
Technical specifications:
Input: DC12V - 24V
USB-C output: 60W (max)
USB A output: 12W (max)
Total Power: 72W
Baseus aluminum 45W USB / USB C car charger:
Charges up to 4 times faster than conventional USB/USB C adapters
Extremely small and light (ideal for travelling)
With support for Power Delivery 3.0 / Quick Charge 4.0
45W output current power
With LED display on the charger
Charge your USB / USB C compatible devices such as smartphones, tablets or MP3 players, etc. in the car now. With the Baseus USB / USB C car charger, your devices are always fully charged while driving. The Baseus Car Charger Auto USB / USB C is ideal for people with active lifestyles who travel a lot. It simply plugs into your vehicle's power outlet (cigarette lighter) and charges while driving.
The power supply also supports the latest Power Delivery 3.0 and Quick Charge 4.0 technologies, with which you can charge your iPhone X up to 50% in just 30 minutes. The car charger always guarantees the maximum charging capacity to charge your electronic devices, with a current output line of up to 6 amps.
ATTENTION: USB/USB C cable not included (can be ordered in store).
The black color
Manufacturer: Baseus
Material: aluminum/plastic
Technical specifications:
Performance/power: 45 watts
Input: 12-24V
USB Output: 4.5V/5A; 5V/4.5A; 9V/3A; 12V/3A; 20V/2.25A
USB-C Output: 5V/3A; 9V/3A; 12V/3A; 15V/3A; 20V/2.25A
Output USB + USB C Total: 5V/6A max
Nmc_alves® said:

Satechi - USB / USB C car charger with 72W:
Simultaneous Charging: Has both a universal USB A port and a Type-C port
Quick Charge: Devices can be charged quickly on the go
Powerful and compact design: Type-C power 60W (max), Type-A power 12W (max), total 72W
Equipped with an LED indicator to check the charging status
With Power Delivery for particularly fast charging
Compatible with almost all USB devices and most USB Type-C devices
The Satechi USB C and USB A Car Charger is the perfect solution for charging your devices on the go. Never worry about how to charge your smartphone, tablet, computer or other device while on the go. Simply connect the charger to your car's cigarette lighter and connect the other end of the USB cable to the USB port of the desired device. You can already charge your device on the go. Satechi's Dual Car Charger allows you to simultaneously charge a 13" MacBook Pro (2016) via the USB-C port and an iPhone/tablet via the USB-A port. The output power for the USB-C port is 60 W (max) and 12 W for the USB-A port.
ATTENTION: The delivery does not include a USB cable!
Color: white/silver
Brand: Satechi
Model: ST-TCPDCCS
Weight: about 34g
Technical specifications:
Input: DC12V - 24V
USB-C output: 60W (max)
USB A output: 12W (max)
Total Power: 72W
Baseus aluminum 45W USB / USB C car charger:
Charges up to 4 times faster than conventional USB/USB C adapters
Extremely small and light (ideal for travelling)
With support for Power Delivery 3.0 / Quick Charge 4.0
45W output current power
With LED display on the charger
Charge your USB / USB C compatible devices such as smartphones, tablets or MP3 players, etc. in the car now. With the Baseus USB / USB C car charger, your devices are always fully charged while driving. The Baseus Car Charger Auto USB / USB C is ideal for people with active lifestyles who travel a lot. It simply plugs into your vehicle's power outlet (cigarette lighter) and charges while driving.
The power supply also supports the latest Power Delivery 3.0 and Quick Charge 4.0 technologies, with which you can charge your iPhone X up to 50% in just 30 minutes. The car charger always guarantees the maximum charging capacity to charge your electronic devices, with a current output line of up to 6 amps.
ATTENTION: USB/USB C cable not included (can be ordered in store).
The black color
Manufacturer: Baseus
Material: aluminum/plastic
Technical specifications:
Performance/power: 45 watts
Input: 12-24V
USB Output: 4.5V/5A; 5V/4.5A; 9V/3A; 12V/3A; 20V/2.25A
USB-C Output: 5V/3A; 9V/3A; 12V/3A; 15V/3A; 20V/2.25A
Output USB + USB C Total: 5V/6A max
Click to expand...
Click to collapse
But I bought the 65W charger and BaseUS said that it can only do PPS 18W.
S23 Ultra requires 10v 4.5 amp to achieve 45 w charging . Charger and Cable both should be capable of 5 amp current capacity and Charger should support PD 3.0 with PPS at 5 amp that is the basic requirement, Cable should have a e-marker chip to identify it as having 5 amp capacity to the charger. usually such cables have 5 amp written on the USB C port and are visibly thicker than the normal 3 amp cables .
ask77 said:
S23 Ultra requires 10v 4.5 amp to achieve 45 w charging . Charger and Cable both should be capable of 5 amp current capacity and Charger should support PD 3.0 with PPS at 5 amp that is the basic requirement, Cable should have a e-marker chip to identify it as having 5 amp capacity to the charger. usually such cables have 5 amp written on the USB C port and are visibly thicker than the normal 3 amp cables .
Click to expand...
Click to collapse
Do you have any reference for that 10V 4.5A information? Some say it's 9V 5A but I never saw any official claims from Samsung regarding that too. I have no issues with cables. I'm using 100W BaseUS cables with e-marker chips on them. They don't have the 5A writing on them but they are obviously thicker than the included Samsung cable (which is only for 25W charging). Here are the specs of the 100W BaseUS desktop charger that I have:
As you can see, it does support PD3.0. Although PPS is not written there, it does support it as well as confirmed by BaseUS support and the video that I showed. I don't see 10V anywhere though so I'm not sure how it works with PPS or something. Does PPS adjust the voltage with fine adjustments or something? Also, that doesn't explain the issue I'm having where SFC 2.0 won't work when two USB ports are used. It only works when the phone is charged alone and this defeats the purpose of buying a multi-port charger in the first place.
Go to settings, about phone , and then status information the last entry there is Rated 10 V 4.5 Amp . Yes pps adjusts voltage with fine adjustment of 20mv . It can provide between 3.3 V to 21 V at upto 5 Amp . Your problem seems to be related to the charger itself which is unable to deliver the required power when two usb ports are used . BTW you can use an app called accubattery which should give you the exact charging data for your phone.
ask77 said:
Go to settings, about phone , and then status information the last entry there is Rated 10 V 4.5 Amp . Yes pps adjusts voltage with fine adjustment of 20mv . It can provide between 3.3 V to 21 V at upto 5 Amp . Your problem seems to be related to the charger itself which is unable to deliver the required power when two usb ports are used . BTW you can use an app called accubattery which should give you the exact charging data for your phone.
Click to expand...
Click to collapse
Ok, I see that now. Well, @Stenlius replied to this thread and says that this is normal. Any comments on that?
What's more weird though is that when it's charging at sfc 2.0, the cable only shows 33w. When I plug in another device in the charger, it renegotiates to sfc 1.0 but still at 33w!
When I use the official 25w samsung charger with the same cable, it goes down to 24w as expected.
SFC 2.0 - So far I have only seen with the Samsung official chargers. I've spent so much money on Belkin, Baseus, UGreen, Anker accessories and never been able to get peak speeds.
JazonX said:
SFC 2.0 - So far I have only seen with the Samsung official chargers. I've spent so much money on Belkin, Baseus, UGreen, Anker accessories and never been able to get peak speeds.
Click to expand...
Click to collapse
Oh wow, that's good to know. Were you getting around the same wattage as I do at 33W? I still have time to return these and is why I'm asking for help here to verify if I don't have an isolated issue or something.
kevindd992002 said:
Oh wow, that's good to know. Were you getting around the same wattage as I do at 33W? I still have time to return these and is why I'm asking for help here to verify if I don't have an isolated issue or something.
Click to expand...
Click to collapse
Never had the tools to measure the wattage output.
I just plug and wait for SFC 2.0 to show up, and if it doesn't - I just get rid of it.
I've tried 120W Xiaomi chargers as well.
Max anything other than samsung genuine chargers can go up to is "Fast Charging" or super charging 1.0.
JazonX said:
Never had the tools to measure the wattage output.
I just plug and wait for SFC 2.0 to show up, and if it doesn't - I just get rid of it.
I've tried 120W Xiaomi chargers as well.
Max anything other than samsung genuine chargers can go up to is "Fast Charging" or super charging 1.0.
Click to expand...
Click to collapse
Well theh that's not the same case as mine. If you read my OP and watched the video, you'll see that I can do sfc 2.0 with this baseus charger but only maxes at 33 watts. I thought you had the same issue as mine.
kevindd992002 said:
Well theh that's not the same case as mine. If you read my OP and watched the video, you'll see that I can do sfc 2.0 with this baseus charger but only maxes at 33 watts. I thought you had the same issue as mine.
Click to expand...
Click to collapse
peak charging only below 20 percent.
after that 3x watt.
after 60 percent 2x watt,same as 25 watt samsung original charger and cable from the box.(3A cable).
basesus gan 2 lite 65 watt and basesus gan 5 pro 65 watt support SFC 2.0.
tested with S23 Ultra.
this image is s23 ultra at 15 percent battery.
charging with samsung original 45 watt charger.
domperidane said:
peak charging only below 20 percent.
after that 3x watt.
after 60 percent 2x watt,same as 25 watt samsung original charger and cable from the box.(3A cable).
basesus gan 2 lite 65 watt and basesus gan 5 pro 65 watt support SFC 2.0.
tested with S23 Ultra.
this image is s23 ultra at 15 percent battery.
charging with samsung original 45 watt charger.
Click to expand...
Click to collapse
Ok, that makes sense. I'll try charging at 15% and see if it makes it to 48W.
Also, have you tried charging yout s23 ultra with more than one usb port plugged in your charger? That does not work as you see in my video.
kevindd992002 said:
Ok, that makes sense. I'll try charging at 15% and see if it makes it to 48W.
Also, have you tried charging yout s23 ultra with more than one usb port plugged in your charger? That does not work as you see in my video.
Click to expand...
Click to collapse
may be there is a problem with your charger.
you can claim warranty.
domperidane said:
may be there is a problem with your charger.
you can claim warranty.
Click to expand...
Click to collapse
No there is none. I posted on reddit before buying this and one guy posted the same issue. Can you test with yours?