Redmi 5A Remove your phone in "black screen"
1. Prepare the battery cover cap, just click on it with a bank card, so that the hex does not slip.
2.The base cover is covered with a cover, THIS WARRANTY LOSS CAUSES!
But you do not have to take the phone to a service, where you have to make sure that the motherboard is replaced by a motherboard, and you do not have to spend weeks!
3.Remove the battery and the motherboard cable (there are a couple of similar connectors, the connectors for the battery cable will be in the middle)!
4. Find the EDL points on the motherboard and use a tweezer (I specifically use an Iphone clip), and then tweak them with the tweezers, then connect a PC or laptop with a USB cable, and you have to set up the following:
https://www.xiaomigeek.com/download-xiaomi-usb-driver-windows.html
https://www.xiaomigeek.com/download-xiaomi-mi-flash-tool.html
Also to fire a fastboat MIUI Rom
5. After installing and installing the driver, install the MIUI FLASH TOOL and download the downloaded and unloaded fastboot ROM into the application, then click on the fresh button (then the clamp does not need to be held in the EDL points) and it appears that which USB port is connected to the phone.
6. Click on the Flash gonbra and fastboot ROM (we will be jamming and starting to install)
7.We're afraid of planting the plant, then we will disconnect the phone from the USB cable. We will put the battery cable back on. We will put everything back on the phone, then put the phone back on, and the phone is ready to go !!!
You can install TWRP and then use TWRP to help you ...
I was hoping to help and do not have to "brick" put the phone on the shelf!
Hi!
Why and how did you brick your phone in the first place? Carelessness?
Related
Hi guys, i realy need your help, my phone is dead.
My I9100 worked fine for two years, I flashed lots of custom firmwares by Odin. Half a moth ago, when I was going to sleep, I plugged in the charger as usually, and noticed, that it started beeping occasionally. On the display it indicated smth like: Charging... than Not Charging... than Charging and so on.
I thought that I plugged the charger incorrectly and replugged it, but it didn't helped. I was very tired and just simply turned the soud off and left the phone charging. In the morning it indicated that it is charging even when the charger was unplugged.
So I've flashed the firmware - no help, than kernel from stock to fillz - no help , than siyah than again to stock - no help. All flashings were maid via CWM. I realized that flashing will not help when I turned off the phone and it was indicating that it is charging.
I decided not to do anythig. Only USB mode didn't worked because when you want to use your phone as USB you should open the apropriate mode on the phone than there will be smth like : plug the USB data cable to enter the USB data transfer mode. I couldn't do this because my phone thought that the cable is already plugged. In forums i've got hints that my micro usb should be cleaned or small board should be replaced. So i decided to clean it. I disassembled the phone and cleaned that board with micro USB. Than turned on the phone, and connected the cable. Phone recognized it and I managed to transfer files from pc to phone. From this point I can say that all terminals on micro USB are ok.
When i unplugged the cable, phone thought that it is plugged((
The most awful part:
I decided to flash it one more time and go to stock via backup made by CWM a year ago.
But during this process the phone made a reboot by itself and after that there was no loading. I can see only name of the device and thats it.
No recovery. Only download mode.
When i connect it to PC in download mode, there is a sound that USB is connected but the device is Unknown. There is no any information about this device in dev manager on PC. I tried two USB cables, all usb ports, two laptops, all versions of USB drivers for my phone.
Earlier, drivers worked well, but now i can't understand where is the problem: Is the problem still connected with my micro usb port or i just erased boot sector and it is already brick.
I gave my phone to service center, they told that they can't help me with this. They say that usb is ok, we don't know why it is not detecting by pc.
Can the board replacement help in this issue or maybe i can do smth. in linux with my device ??? I'll appreciate any suggestions.
Yesterday I talked to representatives of service center and they told me that the problem is that internal memory is damaged and they cant flash the phone.
I took the phone and tried to flash it via Heimdall with brick fix pit.
After using this pit file, the phone was flashed normally and even turned on normally.
But in the phone info menu I saw no any data about internal memory. (It was damaged and required format). I tried format through phone menu and it did nothing.
I decided to flash the phone via Odin with normal 16 GB pit file and had a bad luck. I experienced freez during repartition. After this, phone is a complete brick.
When I connect it to PC without battery pressing vol down and rower buttons it connects as unknown device but there is nothing on the phone display. No recavery no download mode. Nothing - just reflection of my frustrated face).
Currently i'm tring to make a Jtag, maybe it'll put it in the download mode, but hope is dying....
I've herad somewhere that it is possible to put it in the download mode in linux. If somone did this, could you please give me the contact of this person?
Hello, I have issues connecting my S3 international model (i9300) to any PC. It has CM11 since at least 6+ months and it worked just fine and connected to my PC two days ago just fine.
Some days ago, it started bootlooping because of the common power button stuck problem [turned on by itself when battery inserted, and rebooted in the Samsung logo, which doesn't even let you go to DOWNLOAD mode or Recovery because it just reboots after a few seconds]
Yesterday I disassembled it following fixit guides and youtube step by step guides to make sure I didn't break anything. I saw the button problem was internal (the button apparently works fine, but internally it has a closed circuit so it seems as pressed). I assembled my phone again and went to bed. Today it was working without bootloop. I saw this as an opportunity to make all the required backups just in case it went to bootloop again but I couldn't get anything from it. Windows doesn't recognize it at all, not even during boot. Here is what I tried:
*Tried in several PCs/Notebooks/OS with different cables that work with other phones
*In all cases it charges the battery, but the PC doesn't see it as a device.
*I rebooted the phone by software (so I don't press the power button at risk of getting bootloop again) going to terminal emulator and using 'reboot' command.
*Rebooting the phone connected to the PCs doesn't either cause any device to be detected by the PC during the booting of the phone.
*Thinking it might be the port of my phone, I tried an OTG adaptor and several pendrives. They all were detected by the phone and I was able to write and read the USB drives.
Click to expand...
Click to collapse
At first I suspected I left a ribbon/flex cable not connected to the board, but being able to use OTG USB drives and being able to charge it didn't convince me it was the case. I want to avoid disassembling it without knowing first which ribbon to look at and any other test/information you could tell me to provide in order to find the solution.
As I was trying to flash global rom via miflash, It gave an error at %50 helloblabla and stuck at nowhere. Just red led blinking. When I connect it to the pc, It is seen as diagnostics 900e (com10). I hold volume + and - and plug the usb cable after taking out battery and usb cable for 10 seconds and putting them back from back but It doesn't work. I cannot see my device in miflash to flash the device.
Use the deep flash method mentioned here
http://en.miui.com/forum.php?mod=viewthread&tid=310325&extra=page=1&page=1&mobile=2
Had the same issue on my rn3 and was able to recover it using this method(when test point seemed the only option). You just need a copper wire strand to do this. Short the usb 2nd pin as in the video, then remove cable and reinsert. Phone will be detected as unknown device, then update driver and phone will be shown as qdownloader 9008 mode. Next open miflash and flash rom.
tuxing said:
Use the deep flash method mentioned here
http://en.miui.com/forum.php?mod=viewthread&tid=310325&extra=page=1&page=1&mobile=2
Had the same issue on my rn3 and was able to recover it using this method(when test point seemed the only option). You just need a copper wire strand to do this. Short the usb 2nd pin as in the video, then remove cable and reinsert. Phone will be detected as unknown device, then update driver and phone will be shown as qdownloader 9008 mode. Next open miflash and flash rom.
Click to expand...
Click to collapse
See, the person I bought the phone will do it for me. That's not something I want to do.
Use the modified fastboot to reboot to edl from fastboot. google "fastboot edl"
justinxfan said:
Use the modified fastboot to reboot to edl from fastboot. google "fastboot edl"
Click to expand...
Click to collapse
I wish I could go in fastboot mode Device doesn't turn on at all. It needs deep flashing as I can learn. Will do it soon today.
HELLO I was trying to unlock my bootloader by flashing a zip file with mi flash in EDL MODE the result was the device is now bricked it only flashes red led no power on no recognition by computer bootloader locked no fastboot no adb
people suggested something called a deep flash cable to connect straight to the CPU Qualcomm port 9008 now the computer recognize the phone but when I try to flash a ROM it gives cannot receive hello packet error
is there any hope left?:crying:
redmi note 3 pro snapdragon
Only Service center ATM.
aliamiri70007 said:
HELLO I was trying to unlock my bootloader by flashing a zip file with mi flash in EDL MODE the result was the device is now bricked it only flashes red led no power on no recognition by computer bootloader locked no fastboot no adb
people suggested something called a deep flash cable to connect straight to the CPU Qualcomm port 9008 now the computer recognize the phone but when I try to flash a ROM it gives cannot receive hello packet error
is there any hope left?:crying:
redmi note 3 pro snapdragon
Click to expand...
Click to collapse
deep flash cable problem.it should show Qualcomm qdloader 9008 or something.
use testpoint method. i did it once by my self with just a screwdriver and forceps
I connect the phone to PC it shows up as Qualcomm 9008
And flash tool shows as com20 but there is no flash button
We're is the flash button?
aliamiri70007 said:
HELLO I was trying to unlock my bootloader by flashing a zip file with mi flash in EDL MODE the result was the device is now bricked it only flashes red led no power on no recognition by computer bootloader locked no fastboot no adb
people suggested something called a deep flash cable to connect straight to the CPU Qualcomm port 9008 now the computer recognize the phone but when I try to flash a ROM it gives cannot receive hello packet error
is there any hope left?:crying:
redmi note 3 pro snapdragon
Click to expand...
Click to collapse
if deep flash mated ( with deep flash cable) not work for you:
open your phone and disconnect your battery and flash your phone
Please help there is no flash button on flash tool even though the computer says the phone is connected Qualcomm 9008
If red notification light flashes, then you are already in EDL mode, and deep flash cable is nothing but the usb cable which has circuit breaker(switch) between green and white cable... jus buy a cheap data cable from market and peel it partially... now peel the green and white wire... ur deep flash cable is ready.. now insert the cable in pc and phone.. and join the green wire and white wire for 8 seconds... you are in EDL mode.
Hey bro i had faced the same issue that u are on. I had lost hope, but there is solution. There is a video on YouTube -
. This you can watch.
Now the procedure is very simple.
1. Remove the backpanel of your phone( don't worry nothing that serious)but do it carefully as the fingerprint wire is connected already so u should not tear it. Remove the fingerprint cable. Then remove the battery's frap type cable and reinsert it and reinsert the fingerpint one and close the panel. Similar to removing the battery and inserting it again.
2. According to that video, take the copper wire and insert it on the middle pins, very very carefully and insert it in the usb port of your computer. Mind it it might not work at the very first try, due to not applying the wire correctly but for sure it works, so take a small wire and not a bunch of wires and connect it with the port connected to your phone.
3. After inserting let your computer detect it and then remove the Usb cable. Remove the wire. And insert the cable again without wire. Now the port is unlocked and you can easily flash stock os through Mi flash application on pc.
It is super simple and don't panic. Hope you get your phone recovered???.
Don't work it can be fixed,dm me if you haven't already
Hello,
I am presently facing a strange issue with my Honor 4c. Nothing has gone wrong on my phone for almost 1 year but recently, impossible to charge my battery while my phone was on. Today, after a few weeks thinking my phone was just dieing, I have tried to make a back up and wanted to save all my data on my computer. However, impossible to connect my phone to my computer. Then I realized the problem was probably due to my USB parameters (No interface asking for mode to choose when I plug USB).
I finally did my back up but issue is still there : I can only use USB while my phone is OFF... meaning I only charge my phone when it is OFF..
I did not find any solution on internet and did not find an option to allow this interface to come back, even by trying to go in "developer options"
Could you please help?
Thanks
Tahir
Hi , if you did back up , remove all accounts from phone and do Factory Reset , also make sure you are using original usb cable and plug in another usb port ...
i can do factory reset but problem is still . i can use original USB cable but not happen any thing. i check all ports..
when i put phone off it is working like charging. but when i put on Phone it is not working not charging no connect to computer..
plz help