amazfit pace touch does't work - Amazfit

Hi everyone,
my amazfit pace has stopped working, it is switched off and when it comes back on the touch no longer works. I tried to disassociate it but at the restart not working the touch I'm firm at the choice of language.
I took it on gearbest and they offered me the repair with shipping to my load (about 20 €).
Do you think it's convenient?
Is there a way to try and unlock it?
Thank you!

Touchscreen stops working if battery is bellow 5%. If it's not the case, clean it well with a soft dry fabric, turn it off then back on. If it doesn't help, factory reset again using these adb commands with watch connected to computer via USB:
Code:
adb wait-for-device
adb reboot wipe
If it still doesn't work then digitizer failed, you need to replace it.

Related

[Q] how to test touchscreen with adb

Hello, all ROM makers, developers, hackers and advanced users.
I have a problem and hope you can give me some good advice.
Here is my sad story
You can read the full description if you want. Or you can skip it - the main question in the end of this post..
I have bought a new Sony ericsson Live! with walkman (wt19i) phone during my newyear holydays in Prague. It seemd to be working fine.
It is from rev.3, manufacture date 11/49 (mounth/week)
When I came back home and started using it, I saw that after some inactivity period (about couple hours or maybe more) the touch screen, back and menu snsor buttons stops any responsing. Hardware buttons (home, volume, camera, walkman and power) are still working. The system also continues to work as usual, so I can turn it on (but can not slide to unlock), I can hear if somebody calls me (but can not answer). Alarms, notifications and all another functions are still working.
Once or twise it started to work again (by itself, without any actions by me) but after few time the problem repeated. I was very unhappy and sure it was a hardware problem (and of course the Czech warranty does not work in Russia), but now i'm not so sure.
The phone had 4.0.2.A.0.58 firmware (android 2.3.4) from the box. First of all I tried to install SE PC Companion software, connect phone with usb and make factory reset... touchscreen started to work! But soon I saw this problem again.
The next day a new update was released and installed it (firmware .62). My phone was working again, but with the same result after some time.
You shoud know, that simple softreset (or ejecting and inserting battery) has absolutesy no effect on problem. After system starts I can not even unlock it. But flashing a new (or even the same) firmware (with flash tool or SE PCC) makes touchscreen and buttons working for some time. Have no idea why, but installing ROM with CWM (even with full wipe) does not make touch working.
Then I tried to use another custom kernels and ROMs. I unlocked the bootloader with fastboot tool, flashed one of custom ROMs from this forum (pre-rooted and with CWM). Then tried to use CM7.2 ROM... then another kernel and another ROM. Official, official-based, totally unofficial. The problem was with me each time after couple hours
I thought it is because some troubles in lock screen. Tried to install "no lock" app, so my phone did not use lock... but after some time touch freezes in home screen.
I disabled screen off while charging in settings and tried to leave the phone "wired" for some time... actually it worked fine all the time, and when I dicsonnected it it was still working... for couple hours.
I tried to install "no sleep" applications that does not allow CPU and screen to suspend. But it have no influense.
I even flashed CM9.0 ICS (very) beta ROM with the same result.
If it is just hardware problem - why it solves (for some time, but solves) with flashing? If it is a software problem - why it doesnt solve with new kernels and ROMs? My brain is ready to explode.
Now I have only one last idea and ask you to help me.
The question is:
How can I use adb or adb shell comands to get more information about the problem with touch?
I saw there is some log (logcat, stderr) tools, debug tools. I saw working lsmod, dmesg and mount commands in shell.
I think I shoud get all this information when all is ok. And then get it again when touch stops working and then compare, is it a good idea?
Where exactly shoud I see? How to test or get some touch input device info with adb? Is there any item in /dev that i can explore? Or something in dmesg? Where are touch driver located and how can I check if it is working?
I have some basic linux and andriond skills, but have not enought expierence.
I very (VERY) hope somebody can give me any useful advice to continue solving the problem. Where to see, what to do?
Thank you
P.S.: and sorry for mistakes, of course. English is not my native language.
P.P.S.: i am not sure where is the best place for this question: here or in xperia subforums. But I decided that this question is not xperia-specific and can be useful for other people in future.
Anybody? I have Lenovo Yoga B6000 with touchscreen problem and will be good if anyone know how can i test TS through ADB or shell.

Amazfit BIP - Installed Firmware via gadgetbridge - Bricked

Hi,
I installed the 9.14 firmware as instructed on a previous thread.
The uploading of the res and fw file completed in the amazfit bip. However the amazfit reboot and its not opening since.
12hrs already passed and still its not turning on.
What I noticed is that the bluetooth signal can be detected by other phones. Then I can connect via Ble Scanner but it will disconnect.
Is there a way to force flash the firmware?
Thank you.
Same problem here.
Same. Anyway solution so far?
vernel1008 said:
Hi,
I installed the 9.14 firmware as instructed on a previous thread.
The uploading of the res and fw file completed in the amazfit bip. However the amazfit reboot and its not opening since.
12hrs already passed and still its not turning on.
What I noticed is that the bluetooth signal can be detected by other phones. Then I can connect via Ble Scanner but it will disconnect.
Is there a way to force flash the firmware?
Thank you.
Click to expand...
Click to collapse
Only one idea: Delete Gadgetbride, restart your Phone, install Mi Fit-App, Switch your Phone language to english (If isn't) and try to install Firmware again.
HTH
I had the same problem, i was desperate and ready to throw it away, but i finally did what urs1956 said and it worked!! (Only thing is that i paired it with an other device at first).
i am the same probleme but juste uptdate firmware with mi fit... and black screen... bricked...
Nothing work.
Hello,
I have the same issue (black screen) after installed a firmware french, the watch started to upload the new chinise version 1.0.80 when I appaired again the watch with mifit and instead restart : black screen.....
I see the watch in bluetooth but I can't appair it again !!!
Some ideas?
jrebillard said:
Hello,
I have the same issue (black screen) after installed a firmware french, the watch started to upload the new chinise version 1.0.80 when I appaired again the watch with mifit and instead restart : black screen.....
I see the watch in bluetooth but I can't appair it again !!!
Some ideas?
Click to expand...
Click to collapse
Me. too
sleep in black screen.
My conversation with Amazfit/Huasmi
Molly (Amazfit)
Feb 10, 00:47 PST
Hello,
Thank you for contacting Amazfit.
We are very sorry that you have trouble with your device.
Have you ever flashed the ROM of your watch?
Can you please send us a screenshot of your watch screen?
If the screen turned off, please charge it to have a try.
If it doesn't work, please remove the device from the charger, put it on the table, make it untouched for 24-48 hours to let the battery drains and then charge it to see if it solves the issue.
If your issue persists, please get touch with the seller to return the device to have it examined.
Thank you for your understanding!
Sincerely,
Molly | Amazfit Support
Feb 9, 16:19 PST
Amazfit BIP bricked after firmware update: Hi,
I did a firmware update which apparently failed as since then the watch will show a black screen only.
The watch is discoverable in the android bluetooth settings, however, I cannot pair or connect to it.
Is there any way of "forcing" an update via bluetooth?
Kind regards
That same answer from support.
wait for battery drains and then charge it << Not resolve this problem.
I'm wait sinc Last month until now. It's sleeping.
https://amazfitwatchfaces.com/cor/
any news?
Hello,
i have a bricked Amazfit BIP so i decided to open it up.
I saw there is a Winbond 25Q64FWIQ flash onboard, so i'm wondering if anyone has a flash dump to try to reflash mine with a chip programmer

Amazfit Stratos - Looping Startup

When I try to access the fastboot of my Stratos Amazfit it is no longer recognized by the computer. Can someone help me?
It is looping at startup and does not turn on.
I need help getting my watch back.
Thank you in advance.
[email protected]
I'm having the same thing.
It gets to the point of optimizing apps, then starts over. (Repeats nonstop)
Mine was precipitated by installing an apk with android commander.
The apk was supposed to contain a Doctor Who watch face.
Thanks.
tiltawurl said:
I'm having the same thing.
It gets to the point of optimizing apps, then starts over. (Repeats nonstop)
Click to expand...
Click to collapse
Try this using adb (command line), it will erase all data on watch and restart, no requirements besides adb:
Code:
adb reboot wipe
lfom said:
Try this using adb (command line), it will erase all data on watch and restart, no requirements besides adb:
Code:
adb reboot wipe
Click to expand...
Click to collapse
It takes the command and "does something."
One time when it rebooted after the wipe, it only had "total 30" apps to optimize.
Another time, "total 18" apps to optimize.
Still, however, rebooted itself while "launching apps," getting back to its original "total 44" apps to optimize and the reboot loop.
I'm not particularly concerned about loss of data, since I've only had the watch a little over a month,.
Voiding the warranty (rooting) would not be acceptable, since my last resort would be sending it back to Amazfit for reset.
Thanks.
tiltawurl said:
It takes the command and "does something."
One time when it rebooted after the wipe, it only had "total 30" apps to optimize.
Another time, "total 18" apps to optimize.
Still, however, rebooted itself while "launching apps," getting back to its original "total 44" apps to optimize and the reboot loop.
I'm not particularly concerned about loss of data, since I've only had the watch a little over a month,.
Voiding the warranty (rooting) would not be acceptable, since my last resort would be sending it back to Amazfit for reset.
Thanks.
Click to expand...
Click to collapse
You must use the command when it finishes updating apps or it will not work (it will erase all data and restart watch), if you are on Windows:
Code:
adb wait-for-device & adb reboot wipe
If you are on macOS/Linux:
Code:
adb wait-for-device; adb reboot wipe
Other than this, other options require unlocking bootloader, what voids warranty.
Amazfit support sent me a reset tool that worked perfectly.
tiltawurl said:
Amazfit support sent me a reset tool that worked perfectly.
Click to expand...
Click to collapse
dude, can u write e-mail of Amazfit support or something?
i have same problem with my new Stratos 3, commands doesnt help me...(
still hope to resolve this =(
tiltawurl said:
Amazfit support sent me a reset tool that worked perfectly.
Click to expand...
Click to collapse
Can you please share this woderful tool to the community?
Thx in advance!

Stratos - adb swipe

Hello.
Is it possible to send adb swipe command to Stratos? Touch is not working and bootloader is locked but I want to upload trainings before reinstalling ROM. I already tried it but im not sure if im doing sometihng wrong or is it just impossible.
Yes, it works. Try using a remote Android controller app, there are a couple the works (they only require adb).
PS: don't get your hopes high on fixing any hardware issue by reflashing firmware, it is a mith. Unless you flashed the wrong firmware on watch and this caused the problem, reflashing won't help. If watch's bootloader is still locked you should try to contact the seller and get the device replaced Instead...

Amazfit Pace (A1612) can't reset, button not working

Hi everyone,
After hours reading posts, I couldn't find answers for my question. So I got an Amazfit Pace second hand, but it doesn't function as normally would.
The problems so far:
-power button not working
-doesn't connect to smartphone
-wifi, bluetooth, and qr code connection not available
-factory reset from watch just do normal reboot
-from PC can't unlock bootloader, can't wipe the data, can't enter fastboot.
The solutions I've tried so far: full dissasebmly the watch: no corrosion, water damage, broken cables. Downloadad adb tools, and do reset with commands like "adb shell reboot bootloader", "adb wipe reboot", and so on, but every time it just reboots normally. I've downloaded the All In One tool, but it didn't work so far.
I've read similar issues, especially with power button, but those users didn't get answers, and I'm kinda lost.
I would be really happy if someone could direct me to to the right thread, or give hints how to solve this problem. It doesn't matter how hard it is, I did similar things with phones, but this watch is really hard for me...
Thank you for reading it!
selyemretek said:
Hi everyone,
After hours reading posts, I couldn't find answers for my question. So I got an Amazfit Pace second hand, but it doesn't function as normally would.
The problems so far:
-power button not working
-doesn't connect to smartphone
-wifi, bluetooth, and qr code connection not available
-factory reset from watch just do normal reboot
-from PC can't unlock bootloader, can't wipe the data, can't enter fastboot.
The solutions I've tried so far: full dissasebmly the watch: no corrosion, water damage, broken cables. Downloadad adb tools, and do reset with commands like "adb shell reboot bootloader", "adb wipe reboot", and so on, but every time it just reboots normally. I've downloaded the All In One tool, but it didn't work so far.
I've read similar issues, especially with power button, but those users didn't get answers, and I'm kinda lost.
I would be really happy if someone could direct me to to the right thread, or give hints how to solve this problem. It doesn't matter how hard it is, I did similar things with phones, but this watch is really hard for me...
Thank you for reading it!
Click to expand...
Click to collapse
Does touchscreen work? If button and touchscreen don't work, it could be related to a wrong firmware flash, i.e. Stratos firmware instead of Pace.
You can do a factory reset with
Rich (BB code):
adb reboot wipe
But if the problem is related to a firmware issue, bad update,... it may not work.
Firmware issues could be solved flashing stock firmware using Cloner Tool, no need unlocked bootloader, if you can enter into deep flash mode with the button trick. Look for the thread in the forum.
If the problem is hardware related, problably it may have no solution.
Saratoga79 said:
Does touchscreen work? If button and touchscreen don't work, it could be related to a wrong firmware flash, i.e. Stratos firmware instead of Pace.
You can do a factory reset with
Rich (BB code):
adb reboot wipe
But if the problem is related to a firmware issue, bad update,... it may not work.
Firmware issues could be solved flashing stock firmware using Cloner Tool, no need unlocked bootloader, if you can enter into deep flash mode with the button trick. Look for the thread in the forum.
If the problem is hardware related, problably it may have no solution.
Click to expand...
Click to collapse
Thank you for the reply, I tried the "adb reboot wipe" code, but it just keeps rebooting normally like a champ. The PC shows previous songs, and trainings. The touchscreen, stopwatch, timer, compass work, so I can navigate in the watch. I tried that method, just to put it in the deep flash mode by holding down the watch button and reboot from the AIO too, but after the screen lit up and waiting 3-4 secs and double press the button, the watch reboots normally.
At this point I would literally pay someone who can help me.
Edit: I ran the
Rich (BB code):
adb logcat
and while it was running a pressed the power button. It registered, but in the log file it was "'á@'á@" or something (maybe) corrupted code. Also it gave errors for the bluetooth. Here is the log file:
Does Alexa works on amazfit pace, or is there a way to use amazfit pace microphone ?????
Thank you very much Saragota.....
Tigerclaw10000 said:
Does Alexa works on amazfit pace, or is there a way to use amazfit pace microphone ?????
Thank you very much Saragota79.....
Click to expand...
Click to collapse
Tigerclaw10000 said:
Does Alexa works on amazfit pace, or is there a way to use amazfit pace microphone ?????
Thank you very much Saragota.....
Click to expand...
Click to collapse
Look for WOS ROM, it has Verge's Alexa support instead of the Chinese voice assistant. Not sure if it will still work with latest Zepp app versions.
Recently, my PACE also had the same symptoms, without me changing anything in it.
I tried to do a factory reset, but it only reboots.
And I wasn't any smart to unpair with Zepp, now I can't do anything with him anymore.

Categories

Resources