Related
I checked out a few other threads, on a couple forums and dont think anyone has been stupid enough to do this so far...
about 4 months ago, I was lost and my phone was dead, having bodged a car charger together I plugged it in.
The phone turned on, booted up and I got the SatNav software running, but before I could drive off it started flashing.. screen, lights, like a tiny disco....
Then it smoked, quite a lot for a second or two, by this time I'd took battery out and dis-connected the charger but it was too late, the phone was dead.
I got home, put the battery in a desktop charger til it was full and the phone has remained at it's current condition since.
So; it won't turn on, vibrate or flash any lights. The ONLY thing it does, is power up the right hand side bottom white light between the home key and back button.
I've been Ebaying since the day I killed it for a spares one, tried buying a main board but no joy anywhere without paying over £70 (and that's for a complete but knackered handset).
My dad's good with phones, his mate better also both of which said i've burnt out some chips. Some do kinda, have small 'holes' in, and I wiped a 2GB card too, wont work in anything else.
Without spending silly amounts on a new phone can I not do anything with this? Apparently everything except the main board should work (screen, digitizer etc)..
Help anyone please? -ta.
I suggest that you contact your local support team because I think this is something that needs to be examined at a repair center.
http://www.sonyericsson.com/cws/corporate/common/contact/phonelist
I dropped my X10a, and cracked the screen/digitizer. Is it easier to replace the whole housing or just the digitizer? Any suggestions on which company supplies OEM parts at the best prices?
agentJBM said:
I dropped my X10a, and cracked the screen/digitizer. Is it easier to replace the whole housing or just the digitizer? Any suggestions on which company supplies OEM parts at the best prices?
Click to expand...
Click to collapse
I've found some an i will keep looking but here is some at the bottom of my post and if you know of some please do post them here and all update this. good luck
http://forum.xda-developers.com/showthread.php?p=15712166#poststop
well i have an odd problem, one one section of my screen doesn't pick up touches, only the area where the "C" is on the keyboard...its annoying due to thats where the OK buttons are...
i can still navigate sense i can use the track ball..
anyone else have this issue, or something similar?
Try wiping back to factory if stock or reflash the rom if rooted?
I had a weird issue with the touch screen on condemned 18.3 where on the lockscreen trying to drawdown the slider and then draw the pattern, it would freak out and glitch and not follow my finger at all and take several tries to get the pattern correct.
I then wiped and flashed the latest 4.0 GSB and haven't had any issues since.
That's not quite a touch screen failure as yours is, but I thought it would help as an example as something gone wrong and how I was able to remedy it.
i've tried flashing a few different roms, went from cs18.3 to a 2.1 sense rom, back to the latest gsb. it appears its must be a problem with the digitizer...
really sucks, i have to wait to april to upgrade this phone...
might be on craigslist looking for a cheap droid 1...
Ah man, that's unfortunate. Probably wouldn't be worth it to try to replace the screen/digitizer either. Yeah, that's probably your best bet, looking to get another phone. That's how I got my Eris, from craigslist. Great way to go about doing so.
Good luck to ya.
I actually have the same problem and something leads me to believe that an update is causing this. I had it bad a few weeks ago (can't press C, V or X - though I can swipe to the keys sometimes) and then I got a few market updates for Handcent, SuperUser, and something else which then cleared it up for a few days. Then I got more updates and it's back to the failing keyboard!
I really don't know how to pin point it and I haven't done any resetting or testing yet, but I have like gut feeling something is wrong with the software, not the touchscreen since someone else is having this problem.
Mine has been failing little by little. Im now down to the top right corner, bottom left, and bottom middle not responding. It hard to even get the apps drawer to open. It all started with the letter C with me too. Just gets worse.
****, my whole qwerty row doesn't work, neither does the trackball. Upgraded to a SGS2, but I still tinker with the ol' eris.
mine moved, it started working fine for a few days, then just a smaller section to the left of C doesn't work, only really effects when i have an "OK" to press...but track ball still works and typing is so much easier now.
my wife thinks its because i dropped my phone that it started working again
I know this thread is a couple of months old, but...
There's an area on mine at the top right below the notification pull-down that appears to be dead. I'm thinking it's because I've dropped it about 10 times, but nothing looks wrong with the screen otherwise. I've thought about buying a replacement screen for about 15 bucks, but I'll be able to upgrade at the end of March, so I'm really just thinking about holding off (though if the new screen/digitizer worked, it'd make for a good mp3 player with the wifi script).
Digitizer is going bad. Same exact problem happened to mine. I replaced it myself and it works perfect. I found how to videos on youtube and bought a digitizer for about $37 online. Only took a half hour to tear apart and replace. On the difficulty level, I'd give it a 6 or 7.
MBL85 said:
Digitizer is going bad. Same exact problem happened to mine. I replaced it myself and it works perfect. I found how to videos on youtube and bought a digitizer for about $37 online. Only took a half hour to tear apart and replace. On the difficulty level, I'd give it a 6 or 7.
Click to expand...
Click to collapse
YMMV.
Someone gave me an Eris that had digitizer problems along the lower left side of the screen (in portrait orientation). I bought a replacement digitizer ($22 iirc), installed it, and it worked perfectly - for about the first 30 minutes. Then, the problem re-appeared in exactly the same location with the new digitizer.
Same behavior for a variety of stock or developer ROMs, so highly doubtful that it was a "software problem". Very very odd - the chip that does the capacitive sensing is on the flex circuit attached to the digitizer, so it gets replaced when you replace the digitizer; I suppose that the signals that come off the mini-connector between the digitizer assembly and the phone's mobo are only power, ground, and I2C signals.
But there you go; taken all those observations together, I'd suspect that I had a problem on the phone's motherboard which was thermally dependent.
Despite my (negative) experience, the odds are still in favor that a digitizer replacement will fix the problem; but there is an outside chance that it won't.
just sayin',
bftb0
Or, how I learned to not rip open phones on a messy desk.
My S2 was my first android phone, and man has it been an incredible phone. Really the only issue was some lockups with an att update, wherein I switched to ParanoidAndroid.
Unfortunately, recently the phone began having power button issues. It wouldn't wake from power presses, it would wake and work, or it would wake and suddenly restart the phone.
I figured it was the power button, so like a true fool, I got to work ripping open the phone to clean the inner guts.
Attached are a few bad pics I got. Good lord these phones get dirty as hell inside!
After spending 15 minutes cleaning the phone and the crap out of the power button, I went to re-assemble it.
When I realized that it was the volume button I was cleaning.
When I realized the power button dropped when I ripped it open.
The lesson here for me:
Open your phone as a last resort
Open your electronics in clean areas, so when you drop things...
and be careful!
I get these a lot. I can solder a new power button on for $50 including return shipping. You can email me @ seivad17 [at] msn.com if interested.
What's the problem? You just need to replace the power button. If you're not afraid of opening up your phone, then you can surely buy a cheap soldering kit and learn how to solder using youtube videos. That's what I did. You'll fix your phone and learn a very useful skill for a very, very small price.
I opened up my phone to fix the power button, and it started working, even though I didn't do much other than blowing some canned air into the area where the actual switch is. But in taking it apart, the vibrator motor got pulled off of its ribbon cable, so it doesn't work anymore. I've taken it apart a couple other times to look closer and see whether it's something I could just solder back on, or if I could buy a replacement part, but every time I open the case I get one or two new cracks in it, so I don't think I'll open it again to finish the job. I'll just live without the vibrator motor until I get a new phone.
Mine also failed recently due to the power button. It's nearly two years old, so I replaced it anyway. Think I'm going to buy a replacement power switch and see what I can do--maybe give it to a friend or something.
The strange thing is, when I pull it apart and use the phone without the actual power tab (rubber) in the slot, it will work. But not every time. So I'm thinking the button itself was being pressed too firmly while in the case/my pocket, which caused the switch itself to fail.
GiSS88 said:
Mine also failed recently due to the power button. It's nearly two years old, so I replaced it anyway. Think I'm going to buy a replacement power switch and see what I can do--maybe give it to a friend or something.
The strange thing is, when I pull it apart and use the phone without the actual power tab (rubber) in the slot, it will work. But not every time. So I'm thinking the button itself was being pressed too firmly while in the case/my pocket, which caused the switch itself to fail.
Click to expand...
Click to collapse
I had something very similar. Used it for a few days after I switched on the Volume as screen activation (on CM). Then it stopped charging. Ended up being a ribbon cable from charging port to main board was bad. Got it replaced and it's as good as new.
Mine acts strange. When I put the battery, it automatically turns on and power button doesn't work, also USB but if I push USB really hard it gets working but works too bad. I cant make factory restore because of the power button, but also the battery is replacement battery, I charged it outside of the phone with the charger and in 30 minutes dropped from 21% to 10%, even doing nothing. So is it battery problem or my charging dock needs to be replaced? battery is 2200 Mah.
I had the same problem with my Cappy. I was able to get by still because I could still get into recovery. I just downloaded an app from the Play store that allowed me to have advanced reboot option. When I wanted to turn it off I just removed the battery.
I had seen a guy use a type of cleaner for electronic equipment that he sprayed inside a few times and operated the button. He said he was able to fix the problem. I don't remember the spray though.
seivad17 said:
I get these a lot. I can solder a new power button on for $50 including return shipping. You can email me @ seivad17 [at] msn.com if interested.
Click to expand...
Click to collapse
I'm going to fix my s3 and captivate. I looked up how easy it is and I was very pleased. Hoping to get it done soon.
Sent from my LG-D800 using Tapatalk 4
My power button died a few months ago and I've been using an app called "Wake Up Screen!!!" that let's me shake the phone when I want to turn it on.
It's getting a bit old, so I'm thinking of rooting it so I can map the power button to the volume button. Anyone know if I'll need to use the power button during the root process? This stuff is all new to me.
Hello.
So to make a veeeery long story short, the phone leaked water in a lake at about 0.5 meters depth after a minute or two with flaps definitely closed (checked 5-10 times before submersion). The screen then flickered and died.
Phone gets sent away to a service center, tested and results unsurprisingly say its watertight so must be user fault. Sony and service provider refuse to help me in any way to fix the broken phone, so basically they say i have to pay it as normal (it was 4 weeks old at time of damage).
I received the phone back after countless phone calls to sony and service provider trying to get them to take responsibility, especially sony, but to no avail.
So now im trying to fix it myself. I took the phone apart, and the screen connector at the bottom was fried as expected. I bought a new screen and flex connector cable but still my screen wont show. The touchscreen works perfect, and so does the phone. When i connect it to my tv via MHL it works flawlessly. Every function including the new touchscreen works perfect, just that the screen is black on the device.
Am i missing something?? I really want to get this working so i can say IN YOUR FACE to this stupid company SONY. Im thinking the only thing it could be now is some faulty component on the mainboard regarding screen output, seems strange though that everything works perfect via MHL, especially the touchscreen.
Anybody have any ideas? Would be greatly appreciated if anyone can share similar experiences!
Cheers, Vincent from Sweden.
i
vinnibinni said:
Hello.
So to make a veeeery long story short, the phone leaked water in a lake at about 0.5 meters depth after a minute or two with flaps definitely closed (checked 5-10 times before submersion). The screen then flickered and died.
Phone gets sent away to a service center, tested and results unsurprisingly say its watertight so must be user fault. Sony and service provider refuse to help me in any way to fix the broken phone, so basically they say i have to pay it as normal (it was 4 weeks old at time of damage).
I received the phone back after countless phone calls to sony and service provider trying to get them to take responsibility, especially sony, but to no avail.
So now im trying to fix it myself. I took the phone apart, and the screen connector at the bottom was fried as expected. I bought a new screen and flex connector cable but still my screen wont show. The touchscreen works perfect, and so does the phone. When i connect it to my tv via MHL it works flawlessly. Every function including the new touchscreen works perfect, just that the screen is black on the device.
Am i missing something?? I really want to get this working so i can say IN YOUR FACE to this stupid company SONY. Im thinking the only thing it could be now is some faulty component on the mainboard regarding screen output, seems strange though that everything works perfect via MHL, especially the touchscreen.
Anybody have any ideas? Would be greatly appreciated if anyone can share similar experiences!
Cheers, Vincent from Sweden.
Click to expand...
Click to collapse
explain more about phone instead of situation and problem with service center
the touch panel is ok but display is died!
but the phone can boot with another display?!
Geeks Empire said:
explain more about phone instead of situation and problem with service center
the touch panel is ok but display is died!
but the phone can boot with another display?!
Click to expand...
Click to collapse
Hello.
The phone has booted ever since it got water damaged, even with the bad screen. Yes the touch panel works perfect but no display, and i can see and use everything on the phonebon my tv via mhl cable. I even updated firmware whilst using mhl to see if it would help but still no picture on the device.
I have replaced the touch screen and the flex ribbon cable that connects screen to mainboard. I have also removed mainboard and cleaned it with 95% alcohol incase some water or dirt causing a short circuit somewhere.
The mainboard looks fine, and everything works apart from the visual screen. Nothing is overheating. Im really baffled as to what could be wrong, but it surely must be something on the mainboard?
i
vinnibinni said:
Hello.
The phone has booted ever since it got water damaged, even with the bad screen. Yes the touch panel works perfect but no display, and i can see and use everything on the phonebon my tv via mhl cable. I even updated firmware whilst using mhl to see if it would help but still no picture on the device.
I have replaced the touch screen and the flex ribbon cable that connects screen to mainboard. I have also removed mainboard and cleaned it with 95% alcohol incase some water or dirt causing a short circuit somewhere.
The mainboard looks fine, and everything works apart from the visual screen. Nothing is overheating. Im really baffled as to what could be wrong, but it surely must be something on the mainboard?
Click to expand...
Click to collapse
I got same issue on Galaxy S4 but that wasn't water proof so this type of damage was normal for it.
have u tried ur display on another board?
- as Sony said it was user fault... after phone get wet have u tried to dry it with heat?
+ as i read the warranty agreements when u open phone by urself or others (non official center) it will void the warranty.
anyway If ur display not working with another board so thr is problem in display panel and not anything on board.
Please Inform me if u got any info or result of this damage
Thanks
:good:
Geeks Empire said:
I got same issue on Galaxy S4 but that wasn't water proof so this type of damage was normal for it.
have u tried ur display on another board?
- as Sony said it was user fault... after phone get wet have u tried to dry it with heat?
+ as i read the warranty agreements when u open phone by urself or others (non official center) it will void the warranty.
anyway If ur display not working with another board so thr is problem in display panel and not anything on board.
Please Inform me if u got any info or result of this damage
Thanks
:good:
Click to expand...
Click to collapse
Yes the phone is thoroughly dried out. I only opened the phone after i had received it back from sony service. They said it wasnt covered by warranty because it was water damaged and was caused by the user (even though both water indicators behind the 2 flaps are still white and not been exposed to water), and they said that they never repair water damaged phones.
Thats why i decided to open it and try to fix it myself, i had nothing (more) to lose!
I havent tried the new display on another board, thats exactly what i want to do but cant get hold of a new board. I've even been taking apart previous smartphones to see if the display can be connected to it somehow just so i can confirm it works. But the probability is that it does work, as the first "broken" screen worked in the same way as this one, touchscreen fine but no display. Thats why i changed the flex cable also, i thought it must be that when the mainboard seems to be doing everything else perfectly.
Does the problem have to be in one of those 3 components? Screen, flex cable, mainboard, or have i missed something?
Thanks
vinnibinni said:
Yes the phone is thoroughly dried out. I only opened the phone after i had received it back from sony service. They said it wasnt covered by warranty because it was water damaged and was caused by the user (even though both water indicators behind the 2 flaps are still white and not been exposed to water), and they said that they never repair water damaged phones.
Thats why i decided to open it and try to fix it myself, i had nothing (more) to lose!
I havent tried the new display on another board, thats exactly what i want to do but cant get hold of a new board. I've even been taking apart previous smartphones to see if the display can be connected to it somehow just so i can confirm it works. But the probability is that it does work, as the first "broken" screen worked in the same way as this one, touchscreen fine but no display. Thats why i changed the flex cable also, i thought it must be that when the mainboard seems to be doing everything else perfectly.
Does the problem have to be in one of those 3 components? Screen, flex cable, mainboard, or have i missed something?
Thanks
Click to expand...
Click to collapse
Yes, it should be those factors. From what you have stated, its most probably the connector on the main board. Before you make more purchases, try to take it to a shop and ask them to test the screen on another phone, so you can see if its the screen or not. It MIGHT be a faulty flex cable that you just purchased, hopefully, since its the cheaper solution. I actually bought one in ebay that was water damaged, changed the screen, middle frame and flex cable, and have a brand new refurbished Z2, good for me the main board was intact. I would take the board out, wash it with 95% alcohol again with a soft toothbrush to brush impurities off the connector piece. Then spray it a little with electrical spray and leave it in rice to thoroughly dry out overnight and try all the connections again. Look through the main board with a magnifying glass and see if anything obvious burned out, the smallest connection can cause problems.
If all fails, then take it to a shop to test the screen or the main board, hopefully they are friendly enough to do it.
Good luck buddy. :good:
elbello said:
Yes, it should be those factors. From what you have stated, its most probably the connector on the main board. Before you make more purchases, try to take it to a shop and ask them to test the screen on another phone, so you can see if its the screen or not. It MIGHT be a faulty flex cable that you just purchased, hopefully, since its the cheaper solution. I actually bought one in ebay that was water damaged, changed the screen, middle frame and flex cable, and have a brand new refurbished Z2, good for me the main board was intact. I would take the board out, wash it with 95% alcohol again with a soft toothbrush to brush impurities off the connector piece. Then spray it a little with electrical spray and leave it in rice to thoroughly dry out overnight and try all the connections again. Look through the main board with a magnifying glass and see if anything obvious burned out, the smallest connection can cause problems.
If all fails, then take it to a shop to test the screen or the main board, hopefully they are friendly enough to do it.
Good luck buddy. :good:
Click to expand...
Click to collapse
Sounds like good advice elbello
Good to know that you have managed to fix a water damaged Z2 using the same mainboard, hopefully i can have the same luck.
So you think it could be the flex cable? Are they known to break easily?
I have already cleaned the board twice with alcohol, maybe using electrical spray might help, and i will check it with a magnifying glass aswell.
Hopefully i can find a shop that will test the screen for me, but this is Sweden, the place where no favours are done, and where everything has to be sent away and fixed by professionals!
Thanks for the replys guys
I have just checked the whole mainboard with a magnifier, and found no oxidation anywhere. I found quite a bit of dirt in some places, and i have once again cleaned the screen connector with 95% alcohol and also the other side of the board behind the screen connector. I dont have any electrical spray at this time so cant test with that.
Another thing i have realised is that there is visual damage to two contact points that are located at the bottom of the phone, very close to where the flex cable connects to the lcd screen. What are these two contacts for, and could they be causing the problem? I will attach an image of them.
Thanks.
vinnibinni said:
I have just checked the whole mainboard with a magnifier, and found no oxidation anywhere. I found quite a bit of dirt in some places, and i have once again cleaned the screen connector with 95% alcohol and also the other side of the board behind the screen connector. I dont have any electrical spray at this time so cant test with that.
Another thing i have realised is that there is visual damage to two contact points that are located at the bottom of the phone, very close to where the flex cable connects to the lcd screen. What are these two contacts for, and could they be causing the problem? I will attach an image of them.
Thanks.
Click to expand...
Click to collapse
From that picture, I dont think that affects the screen at all. Bad thing is you cant try the two pieces you bought with another board so you can narrow the problem down.
I doubt the electrical spray will make wonders, it just good to clean dirt and make the contacts react better after oxidation, but if you state they are clean...
Think your only options is to consider it a loss, sell it in ebay for parts and stuff, or try getting a new flex and see if it was that, but if it wasnt, its like throwing money away. I would say the same for the screen, but those go for $100+ easily.
elbello said:
From that picture, I dont think that affects the screen at all. Bad thing is you cant try the two pieces you bought with another board so you can narrow the problem down.
I doubt the electrical spray will make wonders, it just good to clean dirt and make the contacts react better after oxidation, but if you state they are clean...
Think your only options is to consider it a loss, sell it in ebay for parts and stuff, or try getting a new flex and see if it was that, but if it wasnt, its like throwing money away. I would say the same for the screen, but those go for $100+ easily.
Click to expand...
Click to collapse
Yea i was thinking about selling it for parts, but its not really worth much without a working mainboard. I will probably just keep it and wait till i can get hold of a new board. How much do you think a new board would cost? I cant find one anywhere at the moment when searching on ebay/google.
Wish i had access to a working board for testing
Hello,
I have the same problem ... black screen on the tv works perfectly, xperia z2 also drowned after 10 seconds under water .... someone back to life solved the screen, that you have replaced?
best regard.
Oscar
vinnibinni said:
Yea i was thinking about selling it for parts, but its not really worth much without a working mainboard. I will probably just keep it and wait till i can get hold of a new board. How much do you think a new board would cost? I cant find one anywhere at the moment when searching on ebay/google.
Wish i had access to a working board for testing
Click to expand...
Click to collapse
Hello ..... no answer .....
I'll buy on aliexpress touch screen digitizer to replace it, anyone know if the screen will return to work? I have to replace more parts? thank you ...
Best Regard
Oscarrrr
Hello,
I'm now in the exact same position.
Water damaged, Touchscreen is still working I can enter recovery any press stuff but no display only shows black.
Had my screen replaced in a shop here but same problem prevails.
They told me to replace Mainboard 3500 THB.
But they didnt have one right then.
He could fix it?
vinnibinni said:
Yea i was thinking about selling it for parts, but its not really worth much without a working mainboard. I will probably just keep it and wait till i can get hold of a new board. How much do you think a new board would cost? I cant find one anywhere at the moment when searching on ebay/google.
Wish i had access to a working board for testing
Click to expand...
Click to collapse
he could you solve your problem? It happens to me the same with a z2 . I board bought new eh and the problem persists . you could help me?
Thinking of buying a used z2 with intermittent touchscreen issues. It works but seems to be intermittent it either takes multiple taps to work or it goes mad like your pressing the keys could this be down to water damage or possibly just a software issue and need re-flashing a ftf by clean install it's a totally stock z2 in mint condition for £50
[email protected] said:
Thinking of buying a used z2 with intermittent touchscreen issues. It works but seems to be intermittent it either takes multiple taps to work or it goes mad like your pressing the keys could this be down to water damage or possibly just a software issue and need re-flashing a ftf by clean install it's a totally stock z2 in mint condition for £50
Click to expand...
Click to collapse
It's probably hardware problem. Trust me, ghost touches make people go crazy,so don't buy it.
Sent from Xperia Z2
Luckily not from an iPhone = Yesterdays technology at tomorrows prices
Ghost touches are a digitizer problem right?
You can buy a new one for about 30-50$
Gesendet von meinem LENNY2 mit Tapatalk
Haldi4803 said:
Ghost touches are a digitizer problem right?
You can buy a new one for about 30-50$
Gesendet von meinem LENNY2 mit Tapatalk
Click to expand...
Click to collapse
Probably yes, but replacing it isn't so easy these days.
Sent from Xperia Z2
Luckily not from an iPhone = Yesterdays technology at tomorrows prices
try this : http://www.mobilerdx.com/2014/10/sony-xperia-z2-display-light-working-problem-solution.html
or this : http://gsm-friends.blogspot.co.id/2015/05/sony-xperia-z2-display-light-ic.html
Hi there,
My girlfriend bought refurbished S6 Edge (from ebay seller) 3 months ago and everything seemed fine for some time. To make this story short, I will skip some details .
After 2 months of use back cover started to detach from the phone. We guessed that problem was in faulty battery and contacted seller immediately, but he never responded. In his ad it was stated that phone comes with 2 year warranty. Then we contacted Samsung and they arranged free shipping to their official service partner.
After almost one more month of waiting, they finally opened it and found out that battery was damaged but someone was already trying to fix that damage before with some tape. They refused to repair it and it was just returned to us as it is.
I was thinking to order a new battery and change it myself, but as it turned out phone now has other problems which were not there before.
- capacitive buttons are not lighting up no matter what (tried everything). Back button only blinks once when booting up.
- adaptive brightness is not working no matter what (it is always on full brightness)
- screen turns off as soon as she presses "call" button
This all looks like problem with proximity and light sensors, but they all seem to work in *#0*# menu, so really not sure what to do.
We already filed a dispute with PayPal, but I guess not much help will come from that. Any suggestion what can we do here?
Thanks!
Sorry man, but it sounds like you're kinda SOL. I would honestly just try selling it as-is before the S7 Edge comes out. That really sucks though.