A2017X_8.x non-treble Adreno 530 GPU DriverFix [email protected]
Suited for : NON-TREBLE OREO 8.x
ALWAYS TAKE A BACKUP BEFORE PROCEEDING !!!
This aroma installer brings you the latest Non-Treble Adreno 530 GPU drivers for a better gaming experience. Less heat, higher fps,…
Source & credits: https://forum.xda-developers.com/mi-mix/development/driver-adreno-530-540-gpu-driver-t3815853
I updated them for our Axon7 so you ony have to install the zip
[B]Installation : [/B]
1. Take a full backup !
2. Flash Adreno GPU Drivers zip
3. Reboot
4. Done !
5. Check aida64 app from playstore / the aida64/display will either show [email protected] in stead of [email protected] In that case you’ve successfully installed new drivers !
Pictures below show GPU before and after install. (this is on 8.1 treble but you will see something similar. As long as it changed to [email protected] you're all ok)
ENJOY !
Huge thanks to @totmakina for testing it on his B23 :good:
Works on b23 china stock firmware?
i guess it is just opengl?
ive looked inside and saw some vulkan api files....nice,gonna try this asap
works here on stock rooted b23 oreo
Thanks
Thanks for the thread. i kinda forgot about this completely (im moving soon and currently im using my phone for xda since my laptop isn't available for me yet)
Don't forget that ppl with stock oreo rom will also get vulkan api back (since its completely missing in stock oreo, at least in the G version)
raystef66 said:
(...)
Click to expand...
Click to collapse
Don't know if it's my carrier, but I get Phone Not Allowed and no signal after I flash this.
I'm on Lineage 20190130; clean install.
GodOfPsychos said:
Thanks for the thread. i kinda forgot about this completely (im moving soon and currently im using my phone for xda since my laptop isn't available for me yet)
Don't forget that ppl with stock oreo rom will also get vulkan api back (since its completely missing in stock oreo, at least in the G version)
Click to expand...
Click to collapse
Same on china oreo,but this driver zip does the upgrade very good
bootloops/stuck on pinguin on stock b23 oreo ( no root,no magisk)
Predatorhaze said:
bootloops/stuck on pinguin on stock b23 oreo ( no root,no magisk)
Click to expand...
Click to collapse
This driver fix is tested on all stock roms now and all were ok after upgrade. Only thing can happen, noticed on Pie, but then we're talking about the treble driverfix, is messing up your screen and the ability to responsiveness due to un-clean flash.
On Oreo stock there's no issue.
You might find the reason on something else.
raystef66 said:
This driver fix is tested on all stock roms now and all were ok after upgrade. Only thing can happen, noticed on Pie, but then we're talking about the treble driverfix, is messing up your screen and the ability to responsiveness due to un-clean flash.
On Oreo stock there's no issue.
You might find the reason on something else.
Click to expand...
Click to collapse
it worked before on b23 stock with magisk and modified boot.img.
I saw you tested this on stock b23 yes,but was it rooted(magisk) or not?
if its something else,then its the motherboard.Ive had treble system but then went back to b23 trough edl.I did not removed the vendor partition before i flashed b23 in miflash
i will try again with the boot img and magisk installed
@raystef66 works on stock b23 rooted magisk 18.1
Works on b02 Oreo with magisk 16.7, but had to wipe cache, otherwise bootloop.
Can i flash this through stock recovery, or only per twrp ?
Im on B23 chinese oreo
Tunox said:
Can i flash this through stock recovery, or only per twrp ?
Im on B23 chinese oreo
Click to expand...
Click to collapse
You could try using stock recovery (install zip from SD) but no garantee (mount system problem)
If you're up to flashing a custom recovery like twrp3218 or 3230 throught EDL, you can do that by renaming it to recovery.img and put it into the folder flash/recovery (in the EDL TOOL). Just flash the recovery, reboot into twrp recovery and flash the file.
After that you can flash the initial stock recovery again if you want.
Ui freeze sometimes with this driver.Sometimes it force reboots,other time it says system has stopped,other time the screen come back.It also drains more power for me
Predatorhaze said:
Ui freeze sometimes with this driver.Sometimes it force reboots,other time it says system has stopped,other time the screen come back.It also drains more power for me
Click to expand...
Click to collapse
As mentioned these drivers are tested on latest Oreo stock roms, for all versions. And all went flawless afaik and no power drains.
Which rom are you applying it to ?
raystef66 said:
As mentioned these drivers are tested on latest Oreo stock roms, for all versions. And all went flawless afaik and no power drains.
Which rom are you applying it to ?
Click to expand...
Click to collapse
Power drain maybe not true but the ui freeze is.I tried on oreo custom and China stock oreo
A2017X_8.x non-treble Adreno 530 GPU DriverFix [email protected]
Suited for : NON-TREBLE OREO 8.x
ALWAYS TAKE A BACKUP BEFORE PROCEEDING !!!
This MODULE brings you the latest Non-Treble Adreno 530 GPU drivers for a better gaming experience. Less heat, higher fps,…
Source & credits: https://forum.xda-developers.com/mi-mix/development/driver-adreno-530-540-gpu-driver-t3815853
I updated them for our Axon7 so you ony have to install the module within magisk and reboot !
Installation :
1. Take a full backup !
2. Flash Adreno GPU Drivers Module in Magisk18.x
3. Reboot
4. Done !
5. Check aida64 app from playstore / the aida64/display will either show [email protected] in stead of [email protected] In that case you’ve successfully installed new drivers !
ENJOY !
Delete
I confirm. The patch works on my A2017U, 8.0.0 stock B20. I used adreno 5xx - v313 rev23 - non-treble.zip.
While with 330 and 331 the phone wouldn't boot.
raystef66 said:
A2017X_8.x non-treble Adreno 530 GPU DriverFix [email protected]
Suited for : NON-TREBLE OREO 8.x
ALWAYS TAKE A BACKUP BEFORE PROCEEDING !!!
This MODULE brings you the latest Non-Treble Adreno 530 GPU drivers for a better gaming experience. Less heat, higher fps,…
Source & credits: https://forum.xda-developers.com/mi-mix/development/driver-adreno-530-540-gpu-driver-t3815853
I updated them for our Axon7 so you ony have to install the module within magisk and reboot !
Installation :
1. Take a full backup !
2. Flash Adreno GPU Drivers Module in Magisk18.x
3. Reboot
4. Done !
5. Check aida64 app from playstore / the aida64/display will either show [email protected] in stead of [email protected] In that case you’ve successfully installed new drivers !
ENJOY !
Click to expand...
Click to collapse
Thanks for this!
Related
This is Touchwiz Nougat for SM-C9000 aka C9LTECHN.
IF YOU FLASH ON C900F YOU DO AT YOUR OWN RISK. YOU HAVE BEEN WARNED
PLEASE BEFORE YOU FLASH ROMS MAKE A COMPLETE BACKUP OF YOUR SYSTEM INCLUDING EFS SO YOU DO NOT BRICK YOUR MOBILE
Modem and Bootloader
Bootloader and Modem from C9000ZHU1BRC2: https://www.androidfilehost.com/?fid=962339331458990219 (SM-C9000)
Stock Odin Firmware
C9000ZHU1BRC2: https://www.androidfilehost.com/?w=files&flid=202643
Roms
Nougat C9000ZHU1BQK1 Debloated: https://www.androidfilehost.com/?fid=889964283620764671 (C900F ported to C9000)
Nougat C9000ZHU1BQK1 DeOdex Debloated: https://www.androidfilehost.com/?fid=673791459329060973 (C900F ported to C9000)
Nougat C9000ZHU1BQL3 Debloated: https://www.androidfilehost.com/?fid=673791459329068625 (Stock HK Firmware)
Nougat C9000ZHU1BQL3 DeOdex Debloated: https://www.androidfilehost.com/?fid=817906626617955776 (Stock HK Firmware)
Nougat C9000ZHU1BRC2 Debloated: https://www.androidfilehost.com/?fid=818070582850509672 (Stock HK Firmware)
Nougat C9000ZZH1BRD1 Debloated: https://www.androidfilehost.com/?fid=674106145207491679 (C900F ported to C9000)
Kernels
Nougat Travis Kernel: https://www.androidfilehost.com/?fid=962157660013070127
Nougat RC2 Stock Kernel: https://www.androidfilehost.com/?fid=962187416754474062
Nougat RD1 Stock Kernel: https://www.androidfilehost.com/?fid=746163614322262568
Xposed for Nougat
https://www.androidfilehost.com/?w=files&flid=229076
These roms includes stock kernel by default and are slightly debloated and or deodexed. Supersu or Magisk is auto installed for root access.
Kernel Features:
Installs SuperSU/Magisk
Permissive
Added IO BFQ Scheduler
Disabled DM_VERITY
Disabled Forced File Encryption
Disabled KNOX
Disabled TIMA
Disabled RKP
Disabled KAP
Disabled Secure Storage
Enabled CIFS Filesystem Support
Enabled NFS Filesystem Support
Increase Battery Charging Levels
Fsync Toggle (Enable/Disable)
Kernel Patched up to 3.10.108
Mild undervolt for our cpu and gpu
Use all cores to boot
F2FS
Ramdisk Optimised
Added core control
Fingerprint fixed fast wakeup enabled
Added more govs
CVE Patches updated as of JAN/2018
Logitech,Microsoft,Sony gamepad support
Kernel Source:
https://github.com/travismills82/c9lte-kernel/commits/Touchwiz-Nougat
very nice rom. very very thank you. you are exellent
ahmetk711 said:
Sen türkmüsün abi ya. Turkcell yazınca. roma tr desteği varmı
Click to expand...
Click to collapse
He is not a turk, and yes there is turkish
evet, turcke dil var
travis82 said:
This is Touchwiz Nougat for SM-C9000
Nougat C9000ZHU1BQK1: https://www.androidfilehost.com/?fid=889964283620764671
Nougat C9000ZHU1BQK1 DeOdex: https://www.androidfilehost.com/?fid=673791459329059940
Nougat Test Kernel: https://androidfilehost.com/?fid=962021903579491176
Nougat QK1 Stock Kernel: https://www.androidfilehost.com/?fid=745849072291687390
Xposed for Nougat: https://www.androidfilehost.com/?w=files&flid=229076
This includes stock kernel and is ported from C900F and is slightly debloated. Magisk is auto installed for root access. I will add more to the main thread here as I cleanup.
Click to expand...
Click to collapse
Wow! this is amazing. You are fast!
Can we flash the same supersu we use on marshmallow to root?
Edit: Thank you @AL_IRAQI
aftermath85 said:
Wow! this is amazing. You are fast!
Can we flash the same supersu we use on marshmallow to root?
Click to expand...
Click to collapse
Yeah
Stuck on samsung galaxy c9 pro screen. can you tell me how can I do that ? instructions ???
MrMutlu said:
Stuck on samsung galaxy c9 pro screen. can you tell me how can I do that ? instructions ???
Click to expand...
Click to collapse
Wipe Data
Flash ROM
Wait for it to boot up ?
which one did you flash ?, i tried it before and it boots up fine
I tried Nougat C9000ZHU1BQK1 DeOdex and I had bootloop. I tried normal and its works fine but battery is decreasing faster.
MrMutlu said:
I tried Nougat C9000ZHU1BQK1 DeOdex and I had bootloop. I tried normal and its works fine but battery is decreasing faster.
Click to expand...
Click to collapse
DeOdex takes a bit longer to boot up, so wait and see
Ok guys 1 I updated deodex try again it might of been my bad **** happens. 2. battery will drain faster till sleep kicks in for apps this should be a known fact right off the table. 3. give it a few days so stuff kicks in your usage is factored in etc. dont be a noob that types before soft kicks in you will just make me go on a wild goose chase with no info can you all give me a debug log before typing crap please seriously? 4th let's get me logs before you upset the dev's your you all are SOL sh!t out of luck on support besides SAMSUCK. Common logic guys and this go's for all devices please.
Thanks
Trav
How is the kernel working that I made please be a bit more vocal it helps me out a lot.
i did'nt used because : i installed after i have set-up fingerprint and pin, after kernel install both pin and fingerprint was unknown, so i put back twrp back-up
criszz said:
i did'nt used because : i installed after i have set-up fingerprint and pin, after kernel install both pin and fingerprint was unknown, so i put back twrp back-up
Click to expand...
Click to collapse
Yea no worries I patched the files in the rom it should be no issue, but I am waiting for the N source to drop cuz like when I worked on Tab S2 I never had an issue with N kernel vs C9. So I know they added in wifi qualcomm source I can tell cuz no more module. So I am hoping I can get the rest perfect like I did tab.
Ok, so do you guys want a port still?, or do you want me to wait for HK Firmware? Both roms work fine on the main op so I'm curious. Next kernel will be Nougat source when Samsung releases it so no more PM'S about that please.
better wait for hk and my personal opinion is to make a rom very colse to stock, remove only app who can be found on market, nothing else, and ofcourse your kernel or stock one. thank you
N source i think it will be a bit better since it will have wifi and better fp firmware in it. My odex rom has all playstore apps removed.
travis82 said:
How is the kernel working that I made please be a bit more vocal it helps me out a lot.
Click to expand...
Click to collapse
I wanted to know if you guys experience a bit slow charging, I'm using the stock kernel & 1.4G rom? ^__^
Still, I am loving our nougat c9pro. Thank you devs and guys
aftermath85 said:
I wanted to know if you guys experience a bit slow charging, I'm using the stock kernel & 1.4G rom? ^__^
Still, I am loving our nougat c9pro. Thank you devs and guys
Click to expand...
Click to collapse
Stock kernel does 1.7a max for fast charge. So it looks like that did not change. Mine I upped it to 2a and I was thinking maybe 2.4a but I don't have a charger to test 2.4 out.
You guys get any slowdowns at all when you fill up ram? I was thinking of Zram and using this instead of a pagefile since the emmc 5.1 chip is slow at read write vs ufs storage. That way all paging will be done in ram and not use the emmc chip. I'll have to try it out this weekend and see if it helps speed up the device in general.
I put odex rom, dirty install and all working fine till now. The same like in barebone prism rom codes like *#06# not working. Must be samsung fault. Very good odex room, no need deodex for me. Also Xposed part from grenify cannot be activated, must be Xposed fault. Thank's Travis82 for rom and hop for hk one soon.
When we recieve HK firmware I have a lot that i will do to speedup the rom and kernel I tested on my port and it was much much much... faster. So until then just wait it up. I noticed same issue as in M that if cores are defined for hotplug that the big cores never slept well to 400mhz so I'll try to get that fixed up when I get source and a new firmware to play with also.
Lineage OS 16 For Xperia X [Treble]Based on Sony Open DevicesI am not responsible for bricked devices, dead SD cards,.Suitable for F5121 and F5122Reboot after your first boot please!
Opinional files:
Disable ForceEncrypt:Link
Required files:
[Tested]
V20190323:Link With: SW_binaries_for_Xperia_Android_9.0_2.3.2_v6_loire.zip
[OEM-Files]
Download Link
How to flash
Read README.txt in zip file please.
Optional step If you want to use a GSI
Flash a GSI compatible System image and boot!
Code:
fastboot flash system < Path of GSI-System.img >
Because of Anti-Rollback, If you want to Use GSI, You need to choose the same or newer one as the treble build date.
Update and known BUG:
V20190323:
Bugs:
1. Quick Charge is broken, you can use computer USB port charge.
2. Camera doesn't work on first boot, you need to reboot.
Source Codes
Sjll Script
Contributors
Sjll @infixremix
ROM OS Version: 9.x Pie
ROM Kernel: Linux 4.x
Paypal
I am very happy to receive your donation.
Version Information
Status: Testing
Created 2019-03-31
Last Updated 2019-03-31
I've used your Treble Pie for a while and it's awesome. Gotta try this as well. Thanks a lot for all the work!
P/s: Can you make a custom overclocked kernel for your Pie ROMs? I've been using Extreme Kernels (for stock Oreo) and they are amazing. I wonder if Pie can also get a similar kernel.
Yeah bro thanks for this work..can you optimize kernel to make sodp rom usable
LOLisLIFE said:
I've used your Treble Pie for a while and it's awesome. Gotta try this as well. Thanks a lot for all the work!
P/s: Can you make a custom overclocked kernel for your Pie ROMs? I've been using Extreme Kernels (for stock Oreo) and they are amazing. I wonder if Pie can also get a similar kernel.
Click to expand...
Click to collapse
lookmanns14 said:
Yeah bro thanks for this work..can you optimize kernel to make sodp rom usable
Click to expand...
Click to collapse
I will try to build a optimize kernel in free time.
Hi,
Can you please help me with the download from the GSI? Where can I get the right file from?
after install, bluetooth and settings tell me that it stops all the time and sim cant be detected. Also there is some encryption so i can't access data or system anymore with twrp... even magisk can't be installed. great...
After running into a ton of errors, I think I've done something wrong. I have a few questions:
1. Where does Disable ForcedEncryption (DFE) go to in the installation process? If I flash the zip before Lineage (or not flasing at all), the phone encrypts itself right on boot. If I flash DFE zip after Lineage, the camera (and all the sensors) die permanently.
2. Regardless of the phone's encryption status, sometimes the phone just fails to recognize all the sensors (except Wifi, battery and GPS). That means no accelerometer, no screen rotation, no compass or light sensor. Rebooting fixes this on Lineage (for a while), but on RR once it occurs all sensors die permanently. Also GPS reception is terrible, as I haven't got a single fix.
Hope anyone who has been using Treble roms could give me an answer. Thanks in advance.
iH8Ecchi said:
After running into a ton of errors, I think I've done something wrong. I have a few questions:
1. Where does Disable ForcedEncryption (DFE) go to in the installation process? If I flash the zip before Lineage (or not flasing at all), the phone encrypts itself right on boot. If I flash DFE zip after Lineage, the camera (and all the sensors) die permanently.
2. Regardless of the phone's encryption status, sometimes the phone just fails to recognize all the sensors (except Wifi, battery and GPS). That means no accelerometer, no screen rotation, no compass or light sensor. Rebooting fixes this on Lineage (for a while), but on RR once it occurs all sensors die permanently. Also GPS reception is terrible, as I haven't got a single fix.
Hope anyone who has been using Treble roms could give me an answer. Thanks in advance.
Click to expand...
Click to collapse
Trust me....its weird (this is what i do with every pie Rom I DONT GUARANTEE SUCCESS ON TREBLE ROMS BECAUSE I WASNT ABLE TO TEST THEM YET)
Flash OEM image which is advertised here
Flash the Rom without anything
Reboot
Go back to recovery by Holding
Power + vol up
Screen turns black= quickly switch to
Power + vol down
Flash disable force encrypt
Reboot
Done!
(Remember to flash anything else that you want)
Some random said:
Trust me....its weird (this is what i do with every pie Rom I DONT GUARANTEE SUCCESS ON TREBLE ROMS BECAUSE I WASNT ABLE TO TEST THEM YET)
Flash OEM image which is advertised here
Flash the Rom without anything
Reboot
Go back to recovery by Holding
Power + vol up
Screen turns black= quickly switch to
Power + vol down
Flash disable force encrypt
Reboot
Done!
(Remember to flash anything else that you want)
Click to expand...
Click to collapse
I only run into these problems on Treble roms. No problem with sensors or encryption with native ones, such as AOSP or Paranoid.
iH8Ecchi said:
I only run into these problems on Treble roms. No problem with sensors or encryption with native ones, such as AOSP or Paranoid.
Click to expand...
Click to collapse
Hmmmmm
Well like that it worked with all pie ROMs that I used
I've been trying to flash this ROM but couldn't flash the Lineage OS Zip file. It says "Zip treble compatibility error!"
"Invalid zip file format!"
can someone please help me out?
Fardin Rehman said:
I've been trying to flash this ROM but couldn't flash the Lineage OS Zip file. It says "Zip treble compatibility error!"
"Invalid zip file format!"
can someone please help me out?
Click to expand...
Click to collapse
Use Twrp-Q (Ask Simeone for Link)
Some random said:
Use Twrp-Q (Ask Simeone for Link)
Click to expand...
Click to collapse
Yeah I have TWRP-Q just need to flash recovery and then try again. Thank you very much for helping
Can anyone please tell me which Gcam can i use on this ROM?
New version of LOS 16 + Treble
This version of LOS is outdated and does not work on latest Treble.
An updated LOS build (with Expanded volume and latest security patch) can be downloaded on this thread and installed over latest Treble.
Since this phone requires arm64 A-only GSIs to boot, the compatible version should be lineage-16.0-2019xxxx-UNOFFICIAL-treble_arm64_avN.img.xz.
Installation tutorial: Click here. Keep in mind that system.img refers to the LOS build above.
Getting Magisk to work: Click here.
iH8Ecchi said:
This version of LOS is outdated and does not work on latest Treble.
An updated LOS build (with Expanded volume and latest security patch) can be downloaded on this thread and installed over latest Treble.
Since this phone requires arm64 A-only GSIs to boot, the compatible version should be lineage-16.0-2019xxxx-UNOFFICIAL-treble_arm64_avN.img.xz.
Installation tutorial: Click here. Keep in mind that system.img refers to the LOS build above.
Getting Magisk to work: Click here.
Click to expand...
Click to collapse
Thanks man the ROM is great! But is it possible to make the camera work like it did on the original Xperia X stock ROM. I mean the camera is pretty dark on all custom ROMs is there any fix for that?
Fardin Rehman said:
Thanks man the ROM is great! But is it possible to make the camera work like it did on the original Xperia X stock ROM. I mean the camera is pretty dark on all custom ROMs is there any fix for that?
Click to expand...
Click to collapse
You can use Chippa_a's Unofficial LOS16 instead. That one has some heating issues and gaming performance might not be optimal (due to CPU throttling), but camera and battery life is almost identical to stock. In fact, I only use Treble LOS as daily driver because I play games on my phone quite a lot.
If you still insist on using Treble however, you can check out Google Camera ports (scroll down a little bit on Treble page). With HDR+ or Night Mode the picture quality is stellar, but taking pictures might be a bit slow. As far as I know it only runs on Treble and Omni.
iH8Ecchi said:
You can use Chippa_a's Unofficial LOS16 instead. That one has some heating issues and gaming performance might not be optimal (due to CPU throttling), but camera and battery life is almost identical to stock. In fact, I only use Treble LOS as daily driver because I play games on my phone quite a lot.
If you still insist on using Treble however, you can check out Google Camera ports (scroll down a little bit on Treble page). With HDR+ or Night Mode the picture quality is stellar, but taking pictures might be a bit slow. As far as I know it only runs on Treble and Omni.
Click to expand...
Click to collapse
Yeah I am using the gcam port and I get pretty good pictures with it but not very good video quality so I guess I'm gonna give it a try to Chippa_a's Unofficial LOS16.
Xperia XZ1 G8341 Vanilla AOSP ROM
This is my first ROM and its fully Vanilla. I Just followed this Build guide without any modifications whatsoever.
The future goal is to build a stable Rom with mostly FOSS Software, stability and useful tools/settings.
Bugs/missing functions i discovered so far:
- Camera Not working always and -> Lens Distortion. Although RAW should be possible.
- Sony Bootlogo has some Artifacts
- No automatic APN setting
- No NFC 25.05 working
- No 90/120Hz mode (or does it?)
- No Display Colour Calibration
- Low Singlethread Geekbench Score (836) and (6060 Multicore) [Governors and schedulers not optimized]
Fingerprint Sensor is working and it takes some time to find Network (not sure if bug or normal).
I hope to find usable answers to those problems + ideas and hope, to receive enough feedback to improve as much as possible.
Just Flash all files (boot, recovery [or any working TWRP], system,vendor, userdata and the OEM Binaries [
SW_binaries_for_Xperia_Android_9.0_2.3.2_v9_yoshino.img] and you should be good to go.
XZ1 Single Sim(25.05.19)
XZ1 Dual Sim
SW_binaries_for_Xperia_Android_9.0_2.3.2_v9_yoshino.img
120Hz Mode
Obviously I am not responsible for bricked devices or anything that this could be related to.
XDA:DevDB Information
RumiRom, ROM for the Sony Xperia XZ1
Contributors
celeron1
ROM OS Version: 9.x Pie
ROM Kernel: Linux 4.x
Based On: Stock AOSP Userdebug
Version Information
Status: Testing
Created 2019-05-25
Last Updated 2019-05-30
Don't use V8 binaries, V9 are out
https://developer.sony.com/file/dow...-for-aosp-pie-android-9-0-kernel-4-9-yoshino/
Worse perfomance is expected because of lack of qti perf framework
marios199546 said:
Don't use V8 binaries, V9 are out
https://developer.sony.com/file/dow...-for-aosp-pie-android-9-0-kernel-4-9-yoshino/
Worse perfomance is expected because of lack of qti perf framework
Click to expand...
Click to collapse
Neat!
Im gonna try these. Thanks a lot.
I would marry if you turn 60fps to 90-120-144 omg plz plz
ΒΕΓΑ said:
I would marry if you turn 60fps to 90-120-144 omg plz plz
Click to expand...
Click to collapse
There is little to nothing about this I could find for the xz1 except one oreo based rom. I have to compile the kernel for it and find out if 60+ hz is really working and how to succesfully implement a toggle option for it. Since im new at this it might take some time without help but its something I want to impliment.
The Xz1s Display obviously is really underperforming in non Sony roms without the "Bravia engine" (colour apperence) imo compared to other open roms. I tried the Bravia magisk module but could not see any difference (also did not checked what it should do at system level).
So if someone has more knowledge feel free to share
I compiled a Kernel from here and modified:
arch/arm64/boot/dts/qcom/dsi-panel-somc-poplar-base-sde.dtsi
arch/arm64/boot/dts/qcom/dsi-panel-somc-poplar-sde.dtsi
arch/arm64/boot/dts/qcom/dsi-panel-somc-poplar.dtsi
(changed 60hz to 90/120hz).
How can I check if the Panel really is working under those frequencies and if other steps are needed?
When compiling I got an Error with drivers/staging/wlan-qc/qcacld-3.0 -> so i removed them from drivers/staging/Kconfig (So apparently no Wifi).
These are the Kernels (boot):
90Hz
*Update 29.05. I Fixed Wifi for the 120Hz version. link in first post
Camera seems to work without problems (also Raw) so I guess there is something wrong with the precompiled Sony Kernel.
Also the Sony bootlogo is not present (no artifakts??)
And again. Flash at own risk.
What about the version for two SIM cards?
Model G8342.
Your rom works perfect on my phone, thanks dev.
Btw, doesn't it support Treble? I cannot boot any of the GSI roms on the forum...
Riskypedia said:
Your rom works perfect on my phone, thanks dev.
Btw, doesn't it support Treble? I cannot boot any of the GSI roms on the forum...
Click to expand...
Click to collapse
It should support Treble.
Maybe you also need to flash "Disable DM Verity" and "Magisk" after
Can be used on G8342 ? ?
Sent from my Sony Xperia XZ1 using XDA Labs
celeron1 said:
I compiled a Kernel from here and modified:
arch/arm64/boot/dts/qcom/dsi-panel-somc-poplar-base-sde.dtsi
arch/arm64/boot/dts/qcom/dsi-panel-somc-poplar-sde.dtsi
arch/arm64/boot/dts/qcom/dsi-panel-somc-poplar.dtsi
(changed 60hz to 90/120hz).
How can I check if the Panel really is working under those frequencies and if other steps are needed?
When compiling I got an Error with drivers/staging/wlan-qc/qcacld-3.0 -> so i removed them from drivers/staging/Kconfig (So apparently no Wifi).
These are the Kernels (boot):
90Hz
120Hz
Camera seems to work without problems (also Raw) so I guess there is something wrong with the precompiled Sony Kernel.
Also the Sony bootlogo is not present (no artifakts??)
And again. Flash at own risk.
Click to expand...
Click to collapse
Can i use this kernel with stock sony rom? (Existenz patched btw...)
ΒΕΓΑ said:
Can i use this kernel with stock sony rom? (Existenz patched btw...)
Click to expand...
Click to collapse
The Kernel is for AOSP (Linux kernel 4.9) so normally it shouldnt work with the Stock Firmware but i dont know if it works with the patched Existenz rom.
therma.cpp said:
What about the version for two SIM cards?
Model G8342.
Click to expand...
Click to collapse
Its for the single Sim.
Im not satisfied with the current State but I can build a dual sim version as well. (Building on hdd due to small SSD so it might take a while)
Screen is not responsive (SOV36). Any suggestions?
update: not the rom. tried to flash different rom and same result.
sinkoo1979 said:
Screen is not responsive (SOV36). Any suggestions?
update: not the rom. tried to flash different rom and same result.
Click to expand...
Click to collapse
Does it respond different while charging?
Is the screen properly clean?
Try flashing the last stock rom > same result?
If not try flashing any gsi > result?
Then full cfw flash + sw binary.
And do factory resets before flashing.
Hoping for the best. Not sure how and if the SOV36 model differs from the rest
celeron1 said:
Does it respond different while charging?
Is the screen properly clean?
Try flashing the last stock rom > same result?
If not try flashing any gsi > result?
Then full cfw flash + sw binary.
And do factory resets before flashing.
Hoping for the best. Not sure how and if the SOV36 model differs from the rest
Click to expand...
Click to collapse
no
yes
no
did not work
works with stock
sinkoo1979 said:
no
yes
no
did not work
works with stock
Click to expand...
Click to collapse
Dis you try one of these GSIs and did you flash the SW-Binaries after?
How "non responsive" is it? Laggy/Not at all/Ghost touches etc.?
Since this is off-Topic i will delete this message after you read it. You shuld open a new Thread where the Problem could be discussed.:good:
celeron1 said:
Dis you try one of these GSIs and did you flash the SW-Binaries after?
How "non responsive" is it? Laggy/Not at all/Ghost touches etc.?
Since this is off-Topic i will delete this message after you read it. You shuld open a new Thread where the Problem could be discussed.:good:
Click to expand...
Click to collapse
Nothing at all
sinkoo1979 said:
Nothing at all
Click to expand...
Click to collapse
Try flashing a oreo based stock rom.(or if you only tried oreo then pie), then flash gsi etc
ΒΕΓΑ said:
I would marry if you turn 60fps to 90-120-144 omg plz plz
Click to expand...
Click to collapse
don't you think it would be the least manner to put some pics of your ass when you come around with "marrying-for-asking"? XD :silly::silly:
New release has arrived but beware! Additional items updated.
Untested version (newest release, don't download): https://drive.google.com/file/d/1V16L3NZBVCwrbJFAo04ckDG_H5gLEalN/view?usp=sharing
This is just the 7.10.12 beta but a bit more optimized than ever. I will be pushing out updates with optimization once a week or month.
This thread is totally about the Redmi 2 (1GB version), Redmi 2 Prime issues won't be covered because you probably won't be using this ROM on it. However this ROM will work like a beast on the 2GB version.
Please do not quote this whole post.
Code:
/*
* Your warranty is now void.
* I am not responsible for bricked devices or dead SD cards.
* Please do some research if you have any concerns about
* how to install/flash this ROM. Or simply ask.
* YOU are choosing to make these modifications, and
* if you point the finger at me for messing up your device,
* I won't be able to help you.
*/
Xposed
SuperSU
Root
BusyBox
Everything will be covered in this thread.
Download links
TWRP : https://www.androidfilehost.com/?fid=962187416754461194
ROM (AFH) : https://www.androidfilehost.com/?fid=6006931924117893861
ROM (GDrive) : https://drive.google.com/open?id=1FDSfd-UwSKMw1nl_ZyTIftRDdkjTrKW1
Xposed : https://www.androidfilehost.com/?fid=6006931924117894520 (Install as a normal apk. Tap on framework > install/update > reboot.)
SuperSU flashable zip: https://www.androidfilehost.com/?fid=6006931924117894517 (Flash it only after MiUi has been completed booted to home/start screen.)
Requirements:
TWRP recovery
Redmi 2 (1GB RAM) phone
Prerequisite:
Do a back up of everything you don't want to lose.
or simply do a nandroid backup.
Note:
You can do factory reset before installing the rom.
However this ROM is downgrade/upgrade compatible which means no matter what your present MiUi is, this will support it.
Update/Upgrade/Downgrade only supported on/over MiUi rom. (If you're on MiUi rom say 9.2.x(last release for Redmi 2)even then you don't need to wipe the data or do a factory reset.)
Procedure:
Copy to external card/memory card. Flash the zip via TWRP recovery. No data wipe/factory reset required (if you're on MiUi). Do factory reset if you want.
OR use adb to sideload the zip while in TWRP adb sideload. Code: adb sideload <filename>.
Cache and dalvik cache wipe is a must.
Known Bugs/Issues:
Music Player's playlist is weirdly arranged while in player screen.
VoLTE doesn't work. Because it is based on 4.4.4 kitkat MiUi8 ROM which never had the VoLTE.
Music Player(if running in background) freezes when RAM is cleaned.
What did I do?:
Removed the possible backdoor SystemAdSolution.apk.
Zipaligned all apks.
Changed few things in build.prop.
Everything under 500mb.
Recommended action post installation:
Do NOT install SuperSU or BusyBox right away. Let the ROM boot for the first time. First boot takes 5 mins.
Download rootuninstaller and remove : BugReport.apk and MiPicks.apk.
You may also remove/uninstall KLO bugreport.
Do NOT uninstall Updater.apk. Turn off auto updates. Do NOT update to newer MiUi versions.
How's it (compared to last/latest MiUi released for Redmi 2)?
It's now more stable when on 4G network. VoLTE/HD calling still not supported.
RAM usage has been optimized. If PUBG is supported, it will run just fine on it.
App opening time has been significantly decreased. You'll enjoy it.
Battery back up has been improved. Charge speed is 1% per minute till 60%.
Latest SuperSU works flawlessly. Xposed works flawlessly. Greenify works.
Few FAQs:
I want Mi Account to work. It will work
I want Mi backup to work. It will work
Can I update play store and apps? Why not? Do it!
I want to update MiUi. Working on it. Just wait and you'll get a better and stable update.
Bootloop! Flash the ROM again from the recovery. Still no factory reset required.
Little bit about the ROM:
ROM Version: 7.10.12
MiUi Version: 7.10.12 Beta Release
ROM Android Version: 4.4.4
ROM Kernel Version: 3.10.28
Stability: Stable
Changelog
1. 11 June 2019 (first release) - HM2014811_signed_061119_211244.zip
[If you're coming from MiUi v9.2.3.0 (last MiUi update for Redmi 2)]
Screen Recorder (stock version) makes a comeback here.
RAM optimization
Battery Improvement. Faster charging (negligible).
More Free RAM when cleaning recent apps. (considering when used Greenify).
Faster App execution than before.
Little to no known bugs.
[If you're coming from any other ROM.]
Fastest MiUi8/9 for Redmi 2 till date.
Everything from the above list follows.
Lemme show you what this MiUi is capable of*. Check attachments.
*The free RAM is because of a RAM booster app, I have uploaded it in the extras post.
Extras
RAM Booster: attached as 2x.apk
Xposed Installer: attached as XpostedInstaller...apk
SuperSU: attached as UPDATE-SuperSU....zip
How to use:
1) RAM Booster: tap on "one click optimization" and then tick select "enable turbo mode" and then tap on "one click randomization" and accept the warning. All app will close and you will have much free RAM from before. Repeat no more than 3 times. Restart the phone once every 24 hours if you're using this booster.
2) Xposed Installer: (SuperSU necessary): Install and update the framework binaries and reboot. And you're done.
3) SuperSU: Install/Flash via TWRP recovery. Wipe Dalvik cache and cache.
Sir @Amosthecoolboy
Is miui 10 possible?
dabakale said:
Sir @Amosthecoolboy
Is miui 10 possible?
Click to expand...
Click to collapse
This thread is currently having the MiUi 8/9.
There might be a possibility of MiUi 10(using themes, afterall MiUi is nothing but a theme) but it will run very slow. It will be nearly useless.
'bro' looks more cool than 'sir'
Any major difference from normal miui?
shivam44 said:
Any major difference from normal miui?
Click to expand...
Click to collapse
RAM optimization and App execution.
Should I wipe system and data if I come from lineage os 15.1?
ttoommxx said:
Should I wipe system and data if I come from lineage os 15.1?
Click to expand...
Click to collapse
unfortunately yes, you will have to wipe the system and data (data especially). Make a nandroid backup before doing so.
@Amosthecoolboy
Please release a build on last stable miui 9
dabakale said:
@Amosthecoolboy
Please release a build on last stable miui 9
Click to expand...
Click to collapse
This one is the first Miui 9. I am working on a version with the latest stable miui 9. Expect it to release before 1st of July.
Amosthecoolboy said:
This one is the first Miui 9. I am working on a version with the latest stable miui 9. Expect it to release before 1st of July.
Click to expand...
Click to collapse
Thanks bro
is there any miui based rom that can bypass miui account?,my phone gets locked and i forget the password
joeyznoise said:
is there any miui based rom that can bypass miui account?,my phone gets locked and i forget the password
Click to expand...
Click to collapse
there is no rom that can do that however there is a tool that can remove or clear the mi account so that you will not be asked to login after the reset.
Why when i try to flash this rom on my redmi 2 prime (2GB Ram Version), it end with fail and say this rom is for wt88047
Ammar MK2 said:
Why when i try to flash this rom on my redmi 2 prime (2GB Ram Version), it end with fail and say this rom is for wt88047
Click to expand...
Click to collapse
wt88047 means 2014811/12/17/18/19/21
and wt86047 means 2014813/816/2014112.
it might not be compatible with redmi 2 prime as I have not tried it.
bro i have 1gb variant but i am getting error 7 in twrp pls help me solve this
vikhyat said:
bro i have 1gb variant but i am getting error 7 in twrp pls help me solve this
Click to expand...
Click to collapse
it may indicate data incompatibility. What rom are you using?
Can you make this compatible for redmi 2 prime (2GB version)?
Ammar MK2 said:
Can you make this compatible for redmi 2 prime (2GB version)?
Click to expand...
Click to collapse
I think it will work on wt88047 which means 2014811/12/17/18/19/21. I don't have the 2GB variant with me to try on.
Analogous to my other projects I present here a custom ROM on stock basis. This ROM is based on the 10.0 DBT FW. It is not supposed to become something big. Actually it was only meant for me, but I thought, maybe it would help some of you who don't want to flash the FWs with Odin.
The ROM is mostly "stock-alike" because I'm no friend of "heavy modifications" anymore.
Neither I nor XDA is responsible for any damage to your device. You flash it at your own risk!
Before you start, make a Nandroid(Backup) of your system. Safe is safe!
Features
Based on last Android 10.0 DBT XXU3BTK1 FW
DBT as CSC active
Stock Kernel
Bluetooth Patch
Removed RMM
Odexed (for better Performance)
Knox-free
A bit debloated (Knox- and MS-stuff)
Stock alike
Flashbable through Custom Recovery
Changelog
Changelog v4.0
Rebased to XXU3BTK1 Android 10.0 (Security Patch from 01.11.2020)
Hopefully Fixxed Bluetooth-Probleme - Should work witout BT Patcher.
Changelog v3.1
Fixxed bluetooth-probs
Patching of bluetooth didnt work anymore, so you have to use now Bluetooth Library Patcher as Magisk Modul, otherwise you lose every reboot your bluetooth connections
Changelog v3.0
Rebased to XXU3BTH4 Android 10.0 (Security Patch from 01.09.2020)
Changelog v2.0
Rebased to XXU3BTFN Android 10.0 (Security Patch from 01.07.2020)
Be on android 10 fw, otherwise it wont work!!!
Changelog v1.0
Initial Release
Rebased to XXS3ATE3 Android 9.0 (Security Patch from 01.05.2020)
What do you need?
actual Custom Recovery, >>here!!<<
my FW (Zip)
are familiar with the matter of flashing:winki:
How to get Root?
You have to patch the TWRP yourself
Alternatively i can provide the patched TWRP see latest twrp file above
Pictures
None, since everybody knows the Stock FWs
Download
Stock ROM Q 10.0 (AndroidFileHost)
Download Modem/Bootloader
Flashable_T510_Firmware (flash it through recovery - follows next!!)
How-To flash:
Place the Zip on the internal or better external memory.
Boot into Recovery -> Hold Vol. Up at restart
--> Fullwipe if coming from another ROM
Then click on install in TWRP
Searches the folder where you put the Zip in
And flash them now by clicking on the zip and dragging the slider to the right at TWRP
Then reboot -> Reboot to System = Boot with Magisk!
The reboot with a fullwipe usually takes a while - can take up to 10 minutes. So keep calm.
Troubeshooting
If you got an bootloop or it stays on samsung logo, make a fullwipe. Otherwis it wont boot correctly into root partition.
I had the same problems. Only a fullwipe solved it.
Credits
Samsung
topjohnwu
MrWaehere
ianmcd
Magendanz
twrp
and others i forgot
If you like it, hit thanks.
XDA:DevDB Information
Stock ROM, ROM for the Samsung Galaxy Tab A series
Contributors
hanspampel
ROM OS Version: 10.x Q
Version Information
Status: Stable
Current Stable Version: 30.08.2020
Created 2020-06-01
Last Updated 2020-09-29
hanspampel said:
Analogous to my other projects I present here a custom ROM on stock basis. This ROM is based on the 9.0 DBT FW. It is not supposed to become something big. Actually it was only meant for me, but I thought, maybe it would help some of you who don't want to flash the FWs with Odin.
The ROM is mostly "stock-alike" because I'm no friend of "heavy modifications" anymore.
Neither I nor XDA is responsible for any damage to your device. You flash it at your own risk!
Before you start, make a Nandroid(Backup) of your system. Safe is safe!
Features
Based on last Android 9.0 DBT XXS3ATE3 FW
DBT as CSC active
Stock Kernel
Bluetooth Patch
Removed RMM
Odexed (for better Performance)
Knox-free
A bit debloated (Knox- and MS-stuff)
Stock alike
Flashbable through Custom Recovery
Changelog
Changelog v1.0
Initial Release
Rebased auf XXS3ATE3 Android 9.0 (Security Patch vom 01.05.2020)
What do you need?
actual Custom Recovery, >>here!!<<
my FW (Zip)
are familiar with the matter of flashing:winki:
How to get Root?
You have to patch the TWRP yourself, alternatively I can provide the patched TWRP.
Pictures
None, since everybody knows the Stock FWs
Download
Stock ROM Pie 9.0 (AndroidFileHost)
Download Modem/Bootloader
Flashable_T510_Firmware (flash it through recovery - follows next!!)
How-To flash:
Place the Zip on the internal or better external memory.
Boot into Recovery -> Hold Vol. Up at restart
--> Fullwipe if coming from another ROM
Then click on install in TWRP
Searches the folder where you put the Zip in
And flash them now by clicking on the zip and dragging the slider to the right at TWRP
Then reboot -> Reboot to System = Boot with Magisk!
The reboot with a fullwipe usually takes a while - can take up to 10 minutes. So keep calm.
Credits
Samsung
topjohnwu
MrWhaere
ianmcd
Magendanz
twrp
and others i forgot
If you like it, hit thanks.
XDA:DevDB Information
Stock ROM, ROM for the Samsung Galaxy Tab A series
Contributors
hanspampel
ROM OS Version: 9.x Pie
Version Information
Status: Stable
Current Stable Version: 01.06.2020
Created 2020-06-01
Last Updated 2020-06-01
Click to expand...
Click to collapse
MOD EDIT : No need to quote the ENTIRE first post ...
Does this rom lag or feel sluggish to you?
Sent from my SM-T510 using Tapatalk
Not more like on Stock. Samsung didnt made a good job with this Tab. It feels more sluggish as on my old Tab A 2016. Maybe its the SoC or the OneUi stuff.
No problem here, using it with custom kernel with oc and everything works fine. As fast as nexus stock
klemen241 said:
No problem here, using it with custom kernel with oc and everything works fine. As fast as nexus stock
Click to expand...
Click to collapse
which kernel are you using on this rom? is it this one?
https://forum.xda-developers.com/galaxy-tab-a/development/kernel-infinity-kernel-1-2-ask1-t4028739
I thought it was made for LineageOS?
zfk110 said:
which kernel are you using on this rom? is it this one?
https://forum.xda-developers.com/galaxy-tab-a/development/kernel-infinity-kernel-1-2-ask1-t4028739
I thought it was made for LineageOS?
Click to expand...
Click to collapse
Yea that's the one. Works with stock too, I checked the frequencies after flashing and it's oc
klemen241 said:
Yea that's the one. Works with stock too, I checked the frequencies after flashing and it's oc
Click to expand...
Click to collapse
What about if you play games? like Pokémon go will it runs hot??
zfk110 said:
What about if you play games? like Pokémon go will it runs hot??
Click to expand...
Click to collapse
I only use it for Netflix, so no idea. I think it's safe
hanspampel said:
Not more like on Stock. Samsung didnt made a good job with this Tab. It feels more sluggish as on my old Tab A 2016. Maybe its the SoC or the OneUi stuff.
Click to expand...
Click to collapse
Its failing CTS profile. any idea how to fix it? on stock firmware without kernel
zfk110 said:
Its failing CTS profile. any idea how to fix it? on stock firmware without kernel
Click to expand...
Click to collapse
no.. safetynet now does hardware checks
Update to Q-based BTFN FW.
Changelog v2.0
Rebased auf XXU3BTFN Android 10.0 (Security Patch vom 01.07.2020)
Be on android 10 fw, otherwise it wont work!!!
Read Troubleshooting in OP!
Thanks for the update.
I am currently using your v1.0 (Android 9).
To update to v2.0 (Android 10) i have to flash stock rom XXU3BTFN first and repeat the procedure to patch TWRP, flash TWRP, flash multidisabler ...?
does the rom work with the T510N version also?
@seppfx
Yepp, you need latets bootloader and twrp etc. Otherwise it won't boot.
@AndroSysQ
Im not confirm what's the difference between both models.
hanspampel said:
@seppfx
Yepp, you need latets bootloader and twrp etc. Otherwise it won't boot.
@AndroSysQ
Im not confirm what's the difference between both models.
Click to expand...
Click to collapse
from what i have read it has 3GB instead of 2GB ram and 64GB instead of 32GB storage.
I think the rest of the internal components are the same.
It is the wifi(T510/T510N) version and not the LTE(T515/T515N)
Hmm try it out if you want. I don't guarantee it will work. If so, it could be that it show not the correct Infos about your tab, ram, emmc etc.
@seppfx
You can push the twrp inside the AP_ file, delete recovery.img and rename twrp to this one. So you don't have to format Data again.
I'm on Android 10. And as you know that TWRP version is T510XXS3ATE3 and TWRP is still not available for T510XXU3BTFN So how am I suppose to do all these stuffs. Can I flash your file through TWRP on Android 9 ?
Please clear my doubts.
No, you must be on android 10, as i said before. Flash Magendanz TWRP. There is a q twrp in his thread.
Can you please post a link of that TWRP ? I'm unable to find that.
Take a look at here.