[Guide] VoLTE + VoWiFi on OPT 3.6.1 OOS - 17 Mar 2019 - OnePlus 2 General

I started searching for a solution to enable VoLTE for OnePlus 2 since the device was not supported by my carrier and stumbled on this thread by dagoban.
Credits goes to dagoban and jamal2367 (his thread in German is here)
Warning:
a. You can break your phone, so make sure you know what you are doing.
b. I've tested this method with quite a number of PIE custom roms, it doesn't work.
Requirements:
a. OxygenOS 3.6.1 - here
b. Root with Magisk 17.3 and add Module VoEnabler 1.4 by Toucan
c. TWRP Recovery version 3.2.1-0
d. Root Explorer
e. Download QPST 2.7.460 from here
f. Download QUD Windows installer QUD.WIN.1.1 Installer-10037.3 Setup.zip from here
g. Put your SIM in slot 1
Steps:
1. Flash OxygenOS 3.6.1
2. Flash TWRP Recovery 3.2.1-0
3. Flash Magisk 17.3 (had issue with later versions, so do not update when prompted)
4. Install QPST 2.7.460 on your Windows PC or Laptop
5. Install QUD on your Windows PC or Laptop
6. Reboot your your Windows PC or Laptop
7. In Magisk 17.3, add VoEnabler-v1.4 module
8. For good measure, reboot OPT
9. Add APN for your SIM if required by carrier
10. In some cases, you might need to call your carrier to make sure that VoLTE is activated for your SIM card
11. In Settings, SIM & Network, Enable VoLTE
12. With Phone (dialer), key in *#801#
13. Set Serial and Full-port switch to ON
14. With Phone (dialer), key in *#*#4636#*#* and check that VoLTE is enabled (show as TURN OFF VOLTE PROVISIONED FLAG)
15. Run PDC app in Administrator Mode (use "Type here to search" to key in PDC, right click on PDC and click on Run as administrator)
16. If QDI comms errors occurs, try other USB ports and reinstall the two software, reboot and try again.
17. In PDC, select your device, click on OEM_Overseas, deactivate Sub0
18. Click on OpenMkt-Commercial-CU, deactivate Sub1
19. Click on Remove button and close PDC
20. Run Root Explorer, navigate to /system/etc/firmware/mbn_ota
21. Delete mcfg_sw_OEM_Overseas-Commercial.mbn
22. Delete mcfg_sw_CMCC_CSFB_DSDS_Comercial_Volte.mbn
[Before Deletion]
[After Deletion]
23. Run PDC app in Administrator Mode again
24. Click on Oversea-Commercial_DS again and click on remove
25. Close and run PDC again
26. Set Volte_OpenMkt-Commercial-CMCC, active Sub0 and Sub1
27. Click on Activate button
28. Close PDC
29. If successful, you should be able to see VoLTE Logo on the right hand side of the status bar
30. If you don't see it, try rebooting your OPT
31. Enjoy
XDA:DevDB Information
[Guide] VoLTE + VoWiFi on OPT 3.6.1 OOS, Tool/Utility for the OnePlus 2
Contributors
zard
Version Information
Status: Testing
Stable Release Date: 2019-03-17
Created 2019-03-17
Last Updated 2019-03-17

Reserved #1

Reserved #2

If it doesn't work on pie then its useless cause all custom roms before pie has volte
Sent from my ONE A2003 using XDA Labs

Vishal Gharat1 said:
If it doesn't work on pie then its useless cause all custom roms before pie has volte
Sent from my ONE A2003 using XDA Labs
Click to expand...
Click to collapse
You're right but my purpose of sharing is because there are users who's carrier has not provided support to OnePlus 2 based on Oxygen OS 3.6.1.
Sent from my Pixel 3 XL using Tapatalk

Here's another method by Airpil, my post at his thread is here https://forum.xda-developers.com/showthread.php?p=79325534.
Using this method, I had successfully gotten VoLTE working on Pixel 2 XL (no VoLTE icon on status bar though) Pie with April patch.
This same method with Magisk 18.2 modded to get diagnostic port also works on Android Q beta 1.
Android Q beta 2 doesn't work, possibly because it needs the latest Magisk Canary build 19003 or 19004 to be modded. There's information on OP of that thread but I don't understand how to do it. If anyone understands how to do it, please reply here or PM me.
Sent from my Pixel 3 XL using Tapatalk

I have two OnePlus phones. One with OnePlus 2 Oxygen 3.6.1. I have made the changes described here and I have VoLTE (but no VOWIFI) on the DIGI.HU mobile network. Hurray!
The Other is OnePlus 3 Oxygen 9.0.3. I also tried and managed VoLTE service on DIGI.HU network.
However, restarting OnePlus 3, the service disappeared and QPST (PDC) never wants to connect to OnePlus 3 again.
Oneplus 2 can still connect to the same laptop on QPST. I tried to install the drivers on another machine ls the program but did not help, no connection.
Can somebody help me?

well thanks....!
it worked on my one plus 3t A3010 model.but after factory reset again the volte disappeared will u give a solution for that....

deepudrone 905 said:
well thanks....!
it worked on my one plus 3t A3010 model.but after factory reset again the volte disappeared will u give a solution for that....
Click to expand...
Click to collapse
It works on VoLTE with airtel sim

Related

Visual voicemail apk request

Can someone provide the stock 5.1 visual voicemail apk for boost mobile variant XT1526?
Or can someone tell me how to stop the "9016" texts on CM12.1?
Sent from my Motorola Moto E 2015 4G LTE (XT1526)
visual voicemail apk fix I used
I did a couple of things the first was to make sure I had correct APN....used MVNOSlayer_R4.zip
Next I used the module SprintVVM-03.04.2017.zip in Magisk Manager
Finally I called Boost and asked them to reset my voicemail too.
After doing those things I haven't had a 9016 message
I am using Moto E xt1526
Another fix to the "9016" repetitive push SMS on both the Virgin Mobile and Boost Mobile variants of the xt1526 is this:
1. Install Minimal ADB & Fastboot on your PC or laptop;
2. Install the most current version of Motorola Device Manager on your PC/laptop (provides current USB Device Drivers for your Motorola device);
3. Ensure USB Debugging is enabled under Developer Options;
4. Ensure your bootloader is unlocked (there are excellent tutorials available here on XDA);
5. Boot your xt1526 into fastboot mode and open a command window iwithin the fadtboot/adb path;
6. Execute this command: fastboot erase carrier.
7. Reboot into the OS & the 9016 SMS push messages should now cease.
crazynapkinman said:
Can someone provide the stock 5.1 visual voicemail apk for boost mobile variant XT1526?
Or can someone tell me how to stop the "9016" texts on CM12.1?
Sent from my Motorola Moto E 2015 4G LTE (XT1526)
Click to expand...
Click to collapse
Try this: https://drive.google.com/file/d/0B4-30E6G5pbIWG8tWmtqX2hUaWc/view?usp=drivesdk
It works like 99%. This should give you a better connection also: https://drive.google.com/file/d/0B4-30E6G5pbIQnZlVlU2SjBpRDQ/view?usp=drivesdk
For me it switches between lte and 3g quicker.
I've been using them for some time and have been meaning to share them, just hadn't yet.
Edit: I should mention I have found the vvm doesn't seem to work on a few roms. One being AEX last time I checked. I forget the others right now. I haven't had a chance to figure out why yet. It does work on most roms though.
The vvm zip works great on AEX now.

Android Pie Beta update for Nokia 6.1 Plus

Beta Labs is closed and the official pie update is rolling out to all the users.
Hello everyone ,
It's a good news for Nokia 6.1 plus users as we have an official update for Android Pie.
It's still in beta so we have to registering order to get that update.
Steps to register for Android Pie beta for Nokia 6.1 Plus :
1. Visit this link [url]https://www.nokia.com/en_int/phones/betalabs[/URL]
2. Sign in or Sign up for the Nokia account
3. Now we have to enter our IMEI number in order to validate our device( You can get it by dialling *#06# or go to Settings > System > About Phone > Status > SIM Status > Network.). Use imei1
4. Next you need is your network provider name( You can get it by going to Settings > System > About Phone > Status > SIM Status > Network.)
5. Select you country
6. Accept the terms and conditions and press "Register for Beta Labs"
7. After its successful validaiton you will get the option to "Request OTA" in the "Get the Beta Software over the air".
Current build number : 00WW_3_25B
Known issues :
Pro Mode Camera Slide up action does not initiate Pro mode
SMS After first OTA of Pie build, SMS may be queued for up to 5 minutes before being successfully sent. After the first instance, all normal thereafter
Display If user does a record, playback, delete video, may on rare occasions see a backlight screen issue
Display Ambient display and auto brightness may not always be optimised
Display On very rare instance, screen may not turn off when in handheld voice call
Display Sometimes, ambient light will not light up in gesture/lifting phone
Camera On occasions, no beauty effect in Bokeh preview mode, but works ok after capture
Camera Low light performance, on occasion, may not be optimised
Actions Pulling down of status bar to open the notification drawer from Notch area is not working
Camera Device may occasionally not be able to exit Slow motion/Time lapse mode after stopping video record
Display When inserting wired headset, screen may turn off after covering proximity sensor.
Note :
1. Build is pretty much stable but few bugs are expected.
2. This method only seems to work for devices shipped with global ROM.
3. We can revert back to Oreo stable build but all the data will be lost in doing so.
Sceint said:
Hello everyone ,
It's a good news for Nokia 6.1 plus users as we have an official update for Android Pie.
It's still in beta so we have to registering order to get that update.
Steps to register for Android Pie beta for Nokia 6.1 Plus :
1. Visit this link https://www.nokia.com/en_int/phones/betalabs
2. Sign in or Sign up for the Nokia account
3. Now we have to enter our IMEI number in order to validate our device( You can get it by dialling *#06# or go to Settings > System > About Phone > Status > SIM Status > Network.). Use imei1
4. Next you need is your network provider name( You can get it by going to Settings > System > About Phone > Status > SIM Status > Network.)
5. Select you country
6. Accept the terms and conditions and press "Register for Beta Labs"
7. After its successful validaiton you will get the option to "Request OTA" in the "Get the Beta Software over the air".
Current build number : 00WW_3_25B
Known issues :
Pro Mode Camera Slide up action does not initiate Pro mode
SMS After first OTA of Pie build, SMS may be queued for up to 5 minutes before being successfully sent. After the first instance, all normal thereafter
Display If user does a record, playback, delete video, may on rare occasions see a backlight screen issue
Display Ambient display and auto brightness may not always be optimised
Display On very rare instance, screen may not turn off when in handheld voice call
Display Sometimes, ambient light will not light up in gesture/lifting phone
Camera On occasions, no beauty effect in Bokeh preview mode, but works ok after capture
Camera Low light performance, on occasion, may not be optimised
Actions Pulling down of status bar to open the notification drawer from Notch area is not working
Camera Device may occasionally not be able to exit Slow motion/Time lapse mode after stopping video record
Display When inserting wired headset, screen may turn off after covering proximity sensor.
Note :
1. Build is pretty much stable but few bugs are expected.
2. This method only seems to work for global ROM.
3. We can revert back to Oreo stable build but all the data will be lost in doing so.
Click to expand...
Click to collapse
Damn. Doesn't work for my device:
"Sorry, it looks like beta labs isn't currently supported on your phone".
Worked for me but i dont think ill install it, these bugs are kinda big for me. Does anyone know when we should get official pie?
sirjohnrl said:
Worked for me but i dont think ill install it, these bugs are kinda big for me. Does anyone know when we should get official pie?
Click to expand...
Click to collapse
I think it might take a month or 2 for it to be stable.
skoop99 said:
Damn. Doesn't work for my device:
"Sorry, it looks like beta labs isn't currently supported on your phone".
Click to expand...
Click to collapse
Do you have a global ROM??
Sceint said:
Do you have a global ROM??
Click to expand...
Click to collapse
I got the same error, that my phone is not supported for beta labs. And yes it's a china variant (TA-1099) with Global ROM.
cleidoscope said:
I got the same error, that my phone is not supported for beta labs. And yes it's a china variant (TA-1099) with Global ROM.
Click to expand...
Click to collapse
My guess is, they must be validating the IMEI to see if it is a device shipped with global ROM or not.
There is an OTA zip link in https://forum.xda-developers.com/android/general/nokia-x6-6-1-plus-software-info-t3832796
You can try that method once.
Sceint said:
My guess is, they must be validating the IMEI to see if it is a device shipped with global ROM or not.
There is an OTA zip link in https://forum.xda-developers.com/android/general/nokia-x6-6-1-plus-software-info-t3832796
You can try that method once.
Click to expand...
Click to collapse
This requires root though, and I have the September patch which means I cannot unlock the bootloader anymore.
Sceint said:
My guess is, they must be validating the IMEI to see if it is a device shipped with global ROM or not.
Click to expand...
Click to collapse
Do you want to say the phones with the model's number TA-1099 and the "global ROM" are official? Is the TA-1099 model not the Chinese version and is not only for China market?
Does the pure China version(TA-1099 model, that is for China market and with the original China ROM) have the same Pie beta update's offer?
I think all 1099s are Chinese versions that manually installed unofficial naked android.
My nokia 6.1 plus model is TA-1083. Can I get the andriod Pie upgrade
Sceint said:
My guess is, they must be validating the IMEI to see if it is a device shipped with global ROM or not.
There is an OTA zip link in https://forum.xda-developers.com/android/general/nokia-x6-6-1-plus-software-info-t3832796
You can try that method once.
Click to expand...
Click to collapse
Hi Sceint,
Can you help to capture Beta Pie roll back Oreo OTA and stable Pie OTA link?:highfive:
How to Capture OTA Update URL for your Android
https://bit.ly/2RBaqX4
Mang Kuki Haokip said:
My nokia 6.1 plus model is TA-1083. Can I get the andriod Pie upgrade
Click to expand...
Click to collapse
Tell you what. Use the link in the OP, and find out.
Has anyone got the stable OTA Android Pie update?
Mang Kuki Haokip said:
My nokia 6.1 plus model is TA-1083. Can I get the andriod Pie upgrade
Click to expand...
Click to collapse
The official update is our and you must have got it.
Xkernels said:
Hi Sceint,
Can you help to capture Beta Pie roll back Oreo OTA and stable Pie OTA link?:highfive:
How to Capture OTA Update URL for your Android
https://bit.ly/2RBaqX4
Click to expand...
Click to collapse
Beta labs is closed for this device now, so I don't think I will be able to capture that link.
Edit :I am on stable update now.
Bookworm Yevgen said:
Has anyone got the stable OTA Android Pie update?
Click to expand...
Click to collapse
Yes, most of the people seems to have got it
i wanted to downgrade my android version from 9 to 8 or 8.1... How can I do that without PC?
Hey. I got Pie yesterday.
Not bad. Annoyingly it seems to handle Bluetooth differently, so my Fitbit stopped working, and I had to re-pair it.
And the screen auto-brightness dims too far sometimes.
Otherwise, nice & stable.
@Sceint okay guys,
I succeeded with converting the v3.38 OTA package by payload_dumper.py into fastboot-flashable images
and uploaded the whole package plus cmd. > https://mega.nz/#!TahAQApb!guFwQxAbA3Vms2gh7x6VOvdDs8WvcrkPgiuHQW
Key:
guFwQxAbA3Vms2gh7x6VOvdDs8WvcrkPgiuHQWblfKc
best regards

VoLTE

Does anybody got VoLTE working with any ROM?
I am on AT&T and AT&T turned off GSM for voice calls and requires VoLTE for LTE. I tried a few ROMs and so far none has VoLTE working. I tried:
MUIU 11.0.4 (Android 9) - doesn't have VoLTE implemented
LOS 17.1 (Android 10) latest build from 20210323 - doesn't have VoLTE implemented. Hacking /system/build.props didn't work
Cipher OS 3.0 (64 bit Android 12) + 0.6 vendor has VoLTE but it is broken. *#*#4636#*#* shows VoLTE provisioned, etc but anytime I am trying to make a call using LTE as network type voice call fail. I still could make calls using WCDMA but then my data is limited to 4G. /vendor/overlay VoLTE fix doesn't seem to work.
OctaviOS 3.4 (32 bit Android 12) + 0.4 vendor has VoLTE but it is broken similarly to Cipher OS 3.0. *#*#4636#*#* shows VoLTE provisioned, but unlike Cipher OS 3.0 buttons are grayed out.
Wulan17 ROMs https://www.pling.com/p/1426249/? Seems to be similar to OctaviOS (at least they too require 0.4-vendor + Magisk in order to boot not into Fastboot). Anybody has any experience with those?

Question Active VOLTE and VOWIFI

Hello friends, I use the device and it does not show me VOLTE, I solved it with the magisk module, it activates the buttons to activate the service and then I select the company profile using the PDC program (it is the same as the volte and vowifi activation of the oneplus 6)
The problem I have is that the change is not permanent, when I restart the cell phone the unwanted profile returns without VOLTE.
Delete the Oversea-Commercial_DS profile but even after reboot the changes are not permanent.
What can you recommend me to solve the problem of activating VOLTE in unsupported countries (which do not have a factory profile)
I clarify to activate I followed the tutorial here
[Guide] VoLTE + VoWiFi working for German carriers
[UPDATE] Updated QPST version + new how to Exciting news, jamal2367 from https://jamal2367.com has developed a way to get VoLTE + VoWifi working for many countries + carriers. If you are on Vodafone and you are having problems with...
forum.xda-developers.com
I have the exact same issue , it reverts back after reboot

How to fix LTE on Andoird 13 GSI on Oneplus Nord N10

I have a nord n10 that i got from tmobile that has unlocked bootloader and is running android 13 gsi the evolutionx version. No matter what gsi I flash it only has an option between 3g and lte, but lte does not work. It shows that its currently on tmobile edge where only messages and calling works. Anyone know a fix to make the lte work?
Did you try that: go into Settings, Phh Treble Settings, IMS features,Install IMS APK for Qualcomm vendor, Reboot the device, Go back to IMS features and request IMS network, and Create IMS APN.
what do I do once I create ims apn.
SupreethChinta06 said:
what do I do once I create ims apn.
Click to expand...
Click to collapse
Go Internet settings/operator settings and enable VoLTE.

Categories

Resources