Related
My tab started giving al kind of errors on internal apps and stuff so i shut it down and now it is in reboot loop.
I can get it into odin download mode or fastboot mode. But i cannot see it with adb or fastboot (it doesent show up when using adb devices or fastboot devices.
i can use odin to do a pda flash but outcome is stil the same.
also did nvflash from Retail 3.1 CWM Recovery, Root & full back up!
al goes fine but after that still no adb reboot recovery or adb devices
iam desperate please help me with this
renedg said:
My tab started giving al kind of errors on internal apps and stuff so i shut it down and now it is in reboot loop.
I can get it into odin download mode or fastboot mode. But i cannot see it with adb or fastboot (it doesent show up when using adb devices or fastboot devices.
i can use odin to do a pda flash but outcome is stil the same.
also did nvflash from Retail 3.1 CWM Recovery, Root & full back up!
al goes fine but after that still no adb reboot recovery or adb devices
iam desperate please help me with this
Click to expand...
Click to collapse
Here's what you do.
Download the file linked below
Download ODIN attached below
Once both are downloaded, extract PDA_SIGNED_P7105.tar
Boot your tablet into ODIN and plug it into your PC
Open the ODIN program on your PC and check the box next to PDA
Click the PDA button and navigate to the file you downloaded earlier
Press Start and let it flash
Once it is done, it will still boot loop.
You need to go into recovery (It will now be the default recovery) and wipe data/factory reset only.
Reboot and it should load up, however you will be on 3.0.1.
You can get back to 3.1 by rooting and installing recovery again or by using the update feature in the tablet's settings.
Good luck!
http://www.mediafire.com/?gcenefqc3khcc0c
renedg said:
My tab started giving al kind of errors on internal apps and stuff so i shut it down and now it is in reboot loop.
I can get it into odin download mode or fastboot mode. But i cannot see it with adb or fastboot (it doesent show up when using adb devices or fastboot devices.
i can use odin to do a pda flash but outcome is stil the same.
also did nvflash from Retail 3.1 CWM Recovery, Root & full back up!
al goes fine but after that still no adb reboot recovery or adb devices
iam desperate please help me with this
Click to expand...
Click to collapse
Please DO NOT ask Questions in the Development forum
Moving to General
When i have done this and go into recovery (power and left volume) i stil get usb icon and download (odin) and still no device found with adb or fastboot (driver i sbeing loaded so somehow my system does regonize it as fastboot or recovery device but with fastboot devices or adb devices still no device in list.
It is alive again. Thanks all who helped out
renedg said:
when i have done this and go into recovery (power and left volume) i stil get usb icon and download (odin) and still no device found with adb or fastboot (driver i sbeing loaded so somehow my system does regonize it as fastboot or recovery device but with fastboot devices or adb devices still no device in list.
Click to expand...
Click to collapse
it is alive again. Thanks all who helped out
You are the man! My IO Galaxy Tab 10.1 is alive again!
Thanks!
Hi All,
I am done the ODIN step, but it still in bootloop mode. I dont know how to do with the Fastboot recover mode. I tried with my Windows 7 and it can't recognized my fastboot driver and stay in the <waiting for device>. Is there any solution for me. Thank you so much.
ericc191 said:
Here's what you do.
Download the file linked below
Download ODIN attached below
Once both are downloaded, extract PDA_SIGNED_P7105.tar
Boot your tablet into ODIN and plug it into your PC
Open the ODIN program on your PC and check the box next to PDA
Click the PDA button and navigate to the file you downloaded earlier
Press Start and let it flash
Once it is done, it will still boot loop.
You need to go into recovery (It will now be the default recovery) and wipe data/factory reset only.
Reboot and it should load up, however you will be on 3.0.1.
You can get back to 3.1 by rooting and installing recovery again or by using the update feature in the tablet's settings.
Good luck!
Click to expand...
Click to collapse
Hello, I have also followed these directions however I am having issues rebooting into recovery using adb.
When I execute adb devices no devices are found.
Any additional help would be appreciated. Thanks
UPDATE:
Success!! I was able to correct the boot loop problem by installing fastboot on a linux machine and running sudo fastboot -w. Also my tablet was in fastboot mode (Power + Volume down, then Select the usb symbol).
Instructions for installing fastboot were found here http://forum.xda-developers.com/showpost.php?p=14675422&postcount=2
boot looping SOLVED! Honeycomb 3.1 google i/o galaxy tab 10.1
[IO TAB] Boot looping? Try this to get your tab back...
I had an issue with my IO 10.1 Tab boot looping. I imagine that this would work for retail as well but have not tried it.
This process will factory reset your device.
You will need fastboot and recovery.img to boot into recovery in order to perform a factory reset.
Fastboot & Stock IO recovery comes from this post as an attachment at the bottom.
You need adb to continue (windows).
1. Extract files to where adb resides (platform-tools folder in android SDk main folder) e.g
C:\Program Files\Android\android-sdk\platform-tools .
2. Plug your tab in to a power source and then hold down the power button until it shuts down. Wait until the tab displays the charging battery.
3. Press and hold the volume down (left button in landscape) and power buttons until the usb and odin icons show up. Volume down to move left and volume up to select the usb logo. Now you should be in fastboot. Plug the usb into your computer.
4. Time to fire up adb!
Start / run / cmd , cd\,
Than, cd to your platform-tools folder or wherever your adb is at. (should be in platform-tools inside of android-sdk-windows)
5. In cmd type "adb start-server" without quotes to start adb. All comands should exclude quotes.
6. Type "fastboot devices" your device serial should appear!If not:
Edit the “<PATH TO ANDROID SDK>\extras\google\usb_driver\android_winusb.inf” file and copy/paste the following lines and add them to the [Google.NTx86] section (for 32bit Windows) and/or [Google.NTamd64] (for 64bit Windows).
NO Empty line above this set, though galaxy tab 10.1v but works for all variants!(tab detected as adb xxx device)
;Galaxy Tab 10.1v
%SingleAdbInterface% = USB_Install, USB\VID_04E8&PID_6860&REV_9999&MI_01
%CompositeAdbInterface% = USB_Install, USB\VID_04E8&PID_6860&MI_01
%SingleAdbInterface% = USB_Install, USB\VID_04E8&PID_6601
%SingleAdbInterface% = USB_Install, USB\VID_0955&PID_7000
;
Download the fastboot zip attached to this post (includes both Win and Linux version) and extract the files to your “<PATH TO ANDROID SDK>\platform-tools” folder
7. Now, type "fastboot boot recovery.img"
8. Now you should boot into recovery. For "adb command lines" to work boot with clockworkmod recovery img (Command and files here: http://droidbasement.com/db-blog/?p=2032)
If you want to try other stuff like push a system restore, kernel or whatever, now you can. If you fail at it, you can always repeat the steps leading up to this point to get back to recovery.
9. Time to just get the tab back! Select "wipe data/factory reset" and confirm, clear cache.
10. After that is done select "reboot device".
Credits to JASKRU from rootwiki, with some additions and modifications extracted from different sources!
for rooting the tab install the zip file from this post in recovery mode (loading recovery.img from fastboot):
http://droidbasement.com/db-blog/?p=2054
P.S don't reboot into recovery with adb command "adb reboot recovery" as it doesn't work, correct way is with fastboot command as mentioned in step 7!
'fastboot' is not recognized as an internal or external command,
operable program or batch file.
FIRST STEP: add the attached fastboot files into the container folder of adb (in sdk folder)
This is mine:
C:\Program Files\Android\android-sdk\platform-tools
of course I did that and mine is in the same folder as yours
I get to step six and thats when it gives me the error
E:\android-sdk-windows\platform-tools>fast boot devices
'fast' is not recognized as an internal or external command,
operable program or batch file.
also when I go to the left instead of odin this is my pic (in attachment)
NOW if I hit the power button and the right on in landscape mode I do get the android system recovery options says Android System Recovery <3e> (pic attached)
I have tried wiping date clearing cache as far as fastboot goes it still doesnt let me in fastboot eventhough im not sure at this point what fastboot even is
I finally got CWM 4.0.0.4 on it but now what because somehow im on 3.0.1 on my tab it wont charge and idk what to do
These steps were tested on 3.1.can you update your firmware from kies or on device?fastboot is needed to boot into the recovery image as in your pic which you already have managed being in older firmware.
E:\android-sdk-windows\platform-tools>fast boot devices
I believe something is still wrong, did you extract the contents of zip file in the platform-tools or the complete folder?Second, how was your tab once in fastboot recongnized by windows it should be as an adb. Device and not fastboot. Third, try manually installing the driver from extras folder, google, usb in android sdk. Last is your system 64bit or 32bit as the modification in inf file should be made accordingly. The only issue is driver or fastboot exe not being in adb folder.
Adding, once in recovery as in the pic, try command adb devices and let know if your device is detected hence you can push a restore fileto your device and reboot or push original recovery.zip file and apply it from sdcard (internal memory).
Last try odin option and flash firmware as tar file mentioned in this forum, try the bootloop or blank screen threads.
tried this route but it cannot find my device via ADB - used the PDANet driver - note i did not get a driver in the extras folder
ideas?
mughalgxt said:
These steps were tested on 3.1.can you update your firmware from kies or on device?fastboot is needed to boot into the recovery image as in your pic which you already have managed being in older firmware.
E:\android-sdk-windows\platform-tools>fast boot devices
I believe something is still wrong, did you extract the contents of zip file in the platform-tools or the complete folder?Second, how was your tab once in fastboot recongnized by windows it should be as an adb. Device and not fastboot. Third, try manually installing the driver from extras folder, google, usb in android sdk. Last is your system 64bit or 32bit as the modification in inf file should be made accordingly. The only issue is driver or fastboot exe not being in adb folder.
Adding, once in recovery as in the pic, try command adb devices and let know if your device is detected hence you can push a restore fileto your device and reboot or push original recovery.zip file and apply it from sdcard (internal memory).
Last try odin option and flash firmware as tar file mentioned in this forum, try the bootloop or blank screen threads.
Click to expand...
Click to collapse
solved my problem -
first fastboot.exe is located in the android-sdk\tools directory. i copied it to my android-sdk\platform-tools directory
Then i get into the tablet's fastboot mode (holding down power + volume down, then select the USB icon) i plug in the cable to my PC's USB, then go to device manager and you should see a fastboot device with an exclamation mark. right click on this and select update driver then navigate to android-sdk\extras\google\usb_driver directory and select android_winusb.inf - it should now install the driver
open up a cmd window and follow the instructions highlighted above starting at step 7
animatechnica said:
solved my problem -
first fastboot.exe is located in the android-sdk\tools directory. i copied it to my android-sdk\platform-tools directory
Then i get into the tablet's fastboot mode (holding down power + volume down, then select the USB icon) i plug in the cable to my PC's USB, then go to device manager and you should see a fastboot device with an exclamation mark. right click on this and select update driver then navigate to android-sdk\extras\google\usb_driver directory and select android_winusb.inf - it should now install the driver
open up a cmd window and follow the instructions highlighted above starting at step 7
Click to expand...
Click to collapse
IN Short, follow the steps in my previous post from 1st till end! Flashing the bootloader file from my thread in development section, is easiest way. Replacing fastboot with recovery option in bootscreen solves many issues for non-developers!
yes and i should add your method was very effective ! thanks
what threw me off initially was not finding the fastboot.exe which was in a different folder and the usbdriver - which needed to be installed separately and can be found by launching SDK manager, selecting Available packages-Third-party Add ons-Google Inc - Google USB Driver Package revision 4
mughalgxt said:
IN Short, follow the steps in my previous post from 1st till end! Flashing the bootloader file from my thread in development section, is easiest way. Replacing fastboot with recovery option in bootscreen solves many issues for non-developers!
Click to expand...
Click to collapse
Thanks!!!
This totally worked!
vokhoa408 said:
Thanks!!!
This totally worked!
Click to expand...
Click to collapse
Is this thing getting Ice cream sandwich?
that might solve all these problems.
Samsung Galaxy Tab 10.1 boot loop
Edit: *Fixed!* Ok, so here is my advice to all you other noobs who bricked your tablet, be AWARE that your tablet actually is conscious, it chooses when it wants to work. Just do everything it says on here, all the fixes I have listed, reboot a bunch of times, yell at it, and when you cry a true tear of pain and remorse, and it splashes down on the surface, it will recognize this and all of a sudden work. Booted to 3.0.1 and going to update, that all that is holy.
Hi Guys, I am having the same problem and need some expert advice please, I have a Samsung Galaxy Tab 10.1 with Android Honeycomb 3.1, running Windows XP Pro SP3
I've gone over every solution to this problem on xda over two days and none have worked for me, either that or i'm not doing it correctly.
I successfully rooted my Tab a few days ago, then tried to install a 'boosted' theme and everything is messed up now. When I boot it just hangs on the samsung loading screen, and it reboots to the same screen.
I have tried wiping data/factory reset in cwm
I have tried wiping cache partition
I have tried running Odin through downloading mode
I have adb and fastboot installed on my computer
I have Samsung Android adb interface driver in Device Manager
I have PDAnet installed
When I boot holding the volume down and power button to get the two options, the only two options I have are the Odin Downloading green guy on the right, and an icon with a box and an arrow coming out of it that takes me to CWM on the left.
So I cannot choose fastboot mode on the Tab, when I try to run 'fastboot flash system new.img' through cmd.exe it just says < waiting for device >
I"m a total noob to this and should have left well enough alone when I successfully rooted it, i'm sure I must be just missing a small step, if I could get a bit of guidance it would be greatly appreciated, thanks.
I have a Vibrant T959. I just flashed from the latest official Cyanogenmod (android 4.2), to the latest unofficial cyanogenmod (Android 4.4.4).
However the phone is crashing in the setup process. I need to get back into clockworkmod, however I have tried the hold vol+, vol-, and power technique tons of times, and it does not work. I had trouble with that method before but would always just use rom manager to reboot to recovery, but needless to say, can't do that this time.
I'm currently attempting to use the ADB to reboot to recovery (which I've never used). I installed the latest JRE, and downloaded ADB, however currently I am unable to get the drivers for my phone. I understand I'm supposed to launch SDK manager to download them, however SDK manager does nothing, just pops up an empty command window for a split second and quits. Did some searching to see if I can download the ADB drivers seperate, but just found many dead, or untrustworthy looking links.
Been reading for hours, but i'm stumped now. All I need to do is just get back to clockworkmod recovery. Is there any way to do so?
Well just an update, by sheer luck I found a roundabout way to get back into recovery. Apparently from all the web searching lots of people are having the same problem with the 3 button combo not working. Supposedly it might be hardware locked.
Here is what worked for me.
Hold volume down and power, and after a couple seconds plug in a usb cord (other end was attached to pc, but no software or anything running)
Keep holding those 2 buttons for about 30 seconds, you'll see the battery icon flash a number of times, along with a little round loading cursor type thing which will also be flashing.
After about 30 seconds, release the power button but keep holding the volume down button for awhile.
After about 10 seconds, clockworkmod recovery pops right up.
Tags (for anyone else who may have this problem: Samsung vibrant T959 how to enter recovery. recovery fix. recovery not working. can't get to clockworkmod.
Try this!
servohead said:
I have a Vibrant T959. I just flashed from the latest official Cyanogenmod (android 4.2), to the latest unofficial cyanogenmod (Android 4.4.4).
However the phone is crashing in the setup process. I need to get back into clockworkmod, however I have tried the hold vol+, vol-, and power technique tons of times, and it does not work. I had trouble with that method before but would always just use rom manager to reboot to recovery, but needless to say, can't do that this time.
I'm currently attempting to use the ADB to reboot to recovery (which I've never used). I installed the latest JRE, and downloaded ADB, however currently I am unable to get the drivers for my phone. I understand I'm supposed to launch SDK manager to download them, however SDK manager does nothing, just pops up an empty command window for a split second and quits. Did some searching to see if I can download the ADB drivers seperate, but just found many dead, or untrustworthy looking links.
Been reading for hours, but i'm stumped now. All I need to do is just get back to clockworkmod recovery. Is there any way to do so?
Click to expand...
Click to collapse
ADB will work. Use the process given below and let me know if it works
1. Install stand alone SDK tools from here, they should work. (h ttp://dl .google.com/android/ins taller_r23-windows.ex e)(Delete all spaces in between.)
2.Note the folder where you have installed SDK tools.
3. Move all the ADB driver files ( Probably 2 .exe and 2 .dll files, or just copy all the files from the ADB driver folder in which you installed the ADB drivers ) to the SDK tools folder.
4.Make sure all usb drivers for your phone have been installed. ( If not just google it, you will find them in the first or second link)
5. Connect your phone and make sure it is recognized by your PC.
6.Navigate to the SDK folder where you have also copied the ADB files. Hold down SHIFT and right click, Select Open Command Window Here.
7. Type adb devices .It should show you all the connected devices, mainly numbers. If not, the ADB drivers have not been installed correctly.
8. If Step 8 works, to reboot into recovery just type " adb reboot recovery " without quotes.
9. Your phone will reboot into recovery .
(If the steps above don't work, you will have to install the latest custom CWM recovery for your device and then boot into recovery from Step 5. And if you get errors while flashing the rom or the custom recovery then you may have to check if signature verification toggle is enabled and disabled,it SHOULD be disabled.And then repeat the flashing process.)
Hope this works . Happy Flashing!:good:
Glad to know it works for you, for people who can't gain access to recovery any other way, ^ This is the way
Dell Venue 7 BOOT PROBLEM
Hello,
I replaced frameworks-res.apk, and others, for change design, but now i can't boot my tab ! , it just booting booting booting booting and booting, factory reset not helped?, can you help me please?
It's Dell Venue 7 3730
ManXXXX said:
Hello,
I replaced frameworks-res.apk, and others, for change design, but now i can't boot my tab ! , it just booting booting booting booting and booting, factory reset not helped?, can you help me please?
It's Dell Venue 7 3730
Click to expand...
Click to collapse
You need to flash again the stock rom, the factory reset won't work.
You can found it here http://forum.xda-developers.com/showpost.php?p=51090040&postcount=2 and flashing through fastboot
I don't know what frameworks-res.apk you used, but maybe you forgot set the right permissions, or maybe you took the files for other device.
DL VN 7
Is there some tutorial for flash with fastboot??, i never did it, and i don't want destroy some other..
Go here to Dell's opensource site.. http://opensource.dell.com/releases/...loper-edition/
Link
No working link
ManXXXX said:
No working link
Click to expand...
Click to collapse
first
sorry for the late reply.
In the dell's opensource page there aren't files for the 3730 (i don't know why)
but, may be i'm wrong, there aren't tutorials for flashing in fastboot, i only found posts in xda's dell venue general forum.
i'll write here a guide if you still without founding a tutorial and for any others if found this post
you need:
intel usb drivershttps://software.intel.com/en-us/android/articles/intel-usb-driver-for-android-devices , read the instruccions if you are in windows 8 (i'm on win7 so i cannot tell you if is the same method or not)
The tools for fastboot (there are in a folder called "google") is a little confused so better download @social-design-concepts miKIT_BATCH HERE (before continue let's say thanks to @social-design-concepts for his useful tool that also works for root ),extract wherever you want in your computer.
the files to flash HEREdownload the package for your device and once donwloaded extract where you want in your computer
NOW FOR FLASH
1.-
Install the intel android usb drivers, if you did this before, skip
2.-
Open the myKIT_BATCH folder and run the "runme.bat" file, then type ACCEPT, after that type 2 and press "enter" (the option 1 is for update the driver, in myKIT_BATCH's post 1 is explained) the font should be red.
3.-
boot into fastboot (press button "power" and button "volume down" at the same time) your tablet's screen will display a blue android with gears inside and below it the "droidboot" text and your device info in your device's top|left screen corner , if yes connect your tablet to pc to recognize it (if is the first time).
4.- Open a command window
after the pc recognizes your tablet unplug and plug again the usb cable, should be faster the recognicion this time.
Then in myKIT_BATCH window press "enter" to refresh, the font will become green and will display your device's info, if is going fine in the window type 4 and press "enter", will appear another window.
IF everything still going fine in the new command window type:
Code:
fastboot devices
will display your device's info
5.- let's start with fastboot
BUT first ENSURE THAT THE BATTERY HAVE A CONSIDERABLE CHARGED LEVEL
Unfortunately i don't know what happens if the tablet power off when flashing and if fastboot will work fine after so check your battery charge first
i need to tell you that the 1-4 steps are the most difficult steps (you should have at this time the rom downloaded and extracted only extract the downloaded package (the .7z file)
after this explained so let's start.
5.1.- WIPING
fastboot have some wipe commands so i will explain the 2 that i used:
Code:
fastboot erase cache
This code explains itself, you can try this code to verify that your device is connected
Code:
fastboot erase data
easy to use but powerful, this will erase app's data and also your internal storage (the 11GB that the tablet have to store files), unfortunately i used this without know and i lost 8GB of files
5.2.- NOW TO FLASH
works almost equal with the wipping commands so it's easy to explain.
let's start with system
for a easy explain you ned to open a window where the rom's files are stored in your pc and in the command shell type "fastboot flash system" and after that drag the system file (system.img.tar.gz) to the command window after dragging the file will appear in the command window the full path of the file
I.E i have a dell venue 8 3830 and i want to flash the jellybean 4.2.2 stock rom so i downloaded the Venue_8_WiFi_JB4.2.2v1.42_FLASHPKG and extract this in F:\VENUE 8 3830\stock rom folder so after type the command and drag and drop the system file in my command window will display this:
Code:
fastboot flash system F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.system.img.gz
after this the command press "enter" and you don't need to do nothing (maybe your window will turn off and maybe you try to turn on but will keep off, don't worry only let fininsh) the fastboot program will start to prepare the file for upload to the tablet and after that to flash.
this will finish in 1-2 minutes.
NOW THE BOOT.IMG
is the same way than system but faster.
after finishing flashing system (when the window diplays the elapsed time) type: "fastboot flash boot" and drag and drop the boot.img file in the command window
I.E. in my device will be like this:
Code:
fastboot flash boot F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.boot.img
press "enter" and will do the same like system prepare,upload and flash the file.
there are in the download package more file but only with BOOT and SYSTEM flashed your tab should boot
but if you want to flash the other images you need to type
for recovery:
Code:
fastboot flash recovery F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.recovery.img
and for fastboot:
Code:
fastboot flash fastboot F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.fastboot.img
for my example, for you will be change a little
thanks to all who read and understand this guide, bad english
you are free to comment this if i mistake
ADB Driver
Isrks said:
first
sorry for the late reply.
In the dell's opensource page there aren't files for the 3730 (i don't know why)
but, may be i'm wrong, there aren't tutorials for flashing in fastboot, i only found posts in xda's dell venue general forum.
i'll write here a guide if you still without founding a tutorial and for any others if found this post
you need:
intel usb drivershttps://software.intel.com/en-us/android/articles/intel-usb-driver-for-android-devices , read the instruccions if you are in windows 8 (i'm on win7 so i cannot tell you if is the same method or not)
The tools for fastboot (there are in a folder called "google") is a little confused so better download @social-design-concepts miKIT_BATCH HERE (before continue let's say thanks to @social-design-concepts for his useful tool that also works for root ),extract wherever you want in your computer.
the files to flash HEREdownload the package for your device and once donwloaded extract where you want in your computer
NOW FOR FLASH
1.-
Install the intel android usb drivers, if you did this before, skip
2.-
Open the myKIT_BATCH folder and run the "runme.bat" file, then type ACCEPT, after that type 2 and press "enter" (the option 1 is for update the driver, in myKIT_BATCH's post 1 is explained) the font should be red.
3.-
boot into fastboot (press button "power" and button "volume down" at the same time) your tablet's screen will display a blue android with gears inside and below it the "droidboot" text and your device info in your device's top|left screen corner , if yes connect your tablet to pc to recognize it (if is the first time).
4.- Open a command window
after the pc recognizes your tablet unplug and plug again the usb cable, should be faster the recognicion this time.
Then in myKIT_BATCH window press "enter" to refresh, the font will become green and will display your device's info, if is going fine in the window type 4 and press "enter", will appear another window.
IF everything still going fine in the new command window type:
Code:
fastboot devices
will display your device's info
5.- let's start with fastboot
BUT first ENSURE THAT THE BATTERY HAVE A CONSIDERABLE CHARGED LEVEL
Unfortunately i don't know what happens if the tablet power off when flashing and if fastboot will work fine after so check your battery charge first
i need to tell you that the 1-4 steps are the most difficult steps (you should have at this time the rom downloaded and extracted only extract the downloaded package (the .7z file)
after this explained so let's start.
5.1.- WIPING
fastboot have some wipe commands so i will explain the 2 that i used:
Code:
fastboot erase cache
This code explains itself, you can try this code to verify that your device is connected
Code:
fastboot erase data
easy to use but powerful, this will erase app's data and also your internal storage (the 11GB that the tablet have to store files), unfortunately i used this without know and i lost 8GB of files
5.2.- NOW TO FLASH
works almost equal with the wipping commands so it's easy to explain.
let's start with system
for a easy explain you ned to open a window where the rom's files are stored in your pc and in the command shell type "fastboot flash system" and after that drag the system file (system.img.tar.gz) to the command window after dragging the file will appear in the command window the full path of the file
I.E i have a dell venue 8 3830 and i want to flash the jellybean 4.2.2 stock rom so i downloaded the Venue_8_WiFi_JB4.2.2v1.42_FLASHPKG and extract this in F:\VENUE 8 3830\stock rom folder so after type the command and drag and drop the system file in my command window will display this:
Code:
fastboot flash system F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.system.img.gz
after this the command press "enter" and you don't need to do nothing (maybe your window will turn off and maybe you try to turn on but will keep off, don't worry only let fininsh) the fastboot program will start to prepare the file for upload to the tablet and after that to flash.
this will finish in 1-2 minutes.
NOW THE BOOT.IMG
is the same way than system but faster.
after finishing flashing system (when the window diplays the elapsed time) type: "fastboot flash boot" and drag and drop the boot.img file in the command window
I.E. in my device will be like this:
Code:
fastboot flash boot F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.boot.img
press "enter" and will do the same like system prepare,upload and flash the file.
there are in the download package more file but only with BOOT and SYSTEM flashed your tab should boot
but if you want to flash the other images you need to type
for recovery:
Code:
fastboot flash recovery F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.recovery.img
and for fastboot:
Code:
fastboot flash fastboot F:\VENUE 3830\stock rom\VENUE_8_WIFI_JB4.2.2v1.42.fastboot.img
for my example, for you will be change a little
thanks to all who read and understand this guide, bad english
you are free to comment this if i mistake
Click to expand...
Click to collapse
When i installing the driver, always: Install failed, i have Windows 10 and i added language code
ManXXXX said:
When i installing the driver, always: Install failed, i have Windows 10 and i added language code
Click to expand...
Click to collapse
I found this around here, is for windows 8 but maybe useful for Windows 10
https://software.intel.com/en-us/android/articles/how-to-install-intel-usb-driver-for-android-devices-on-windows-8
ADB Driver
Nah nah this, i think ADB driver.
ManXXXX said:
Nah nah this, i think ADB driver.
Click to expand...
Click to collapse
unfortunately i don't have a computer with windows 10 so i can't solve easily.
i found this googling, so with a little of faith :fingers-crossed: , is the same error than yours http://android.stackexchange.com/questions/118823/how-to-install-adb-drivers-on-windows-10-opoit's for the OPO, but is about the same "intalling adb driver", so could work
in a dessesperate attempt, you can use the update usb drivers in "myKit_BATCH" typing "1" after typyng "ACCEPT"
I fixed it with 15 seconds installer!, i gng try to fix tablet
But i found next problem, after connect tab to PC, just UNKNOWN, and tab is not showing in mykit
ManXXXX said:
But i found next problem, after connect tab to PC, just UNKNOWN, and tab is not showing in mykit
Click to expand...
Click to collapse
Ahh that's add driver not recognize your tablet, I suppose that you connect in fastboot mode,
Try using the option of update the adb driver in Mykit_BATCH, you don't lose nothing trying.
Other option is trying the dell's method http://opensource.dell.com/releases/Venue_8_3830_CloverTrail_plus/developer-edition/Download the pdf file and read the instructions from page 2 to page 9 if still not working
here is the sdk tools for windows that the pdf wants
I downloaded SDK tools, i installed Google usb driver, because it say not installed, when it was installing it said: Disable adb driver, ineffectual, error code -1, but after install it work good, so i will test with this, when no i will try another way, that u wrote here
Finally, tried method, no work, finally, update ADB no working for me, cuz installation always fail, next one DELL method, working but i found problem, dell wrote update driver via google extra with codes, BUT
My first code: USB\VID_413C&PID_B119&REV_????, ????, i think there is something wrong
My second code: USB\VID_413C&PID_B119, i think this one is alright, but then up
Finally with dell next page i'm in!, but my kit no working, in every command shut down, so i using windows cmd, it working too
Mhm bruh, no i'm in flash system, sending 'system' awesome, but it's more than 2 minutes , when it will work, omg u r awesome
Bruh, yay, i did it, thq u r master <33
ManXXXX said:
Bruh, yay, i did it, thq u r master <33
Click to expand...
Click to collapse
Are you telling that the dell method works?
The good new is that your tablet is back (with some problems in the way but work, ). after all now you know how to flash through fastboot. If anyelse goes wrong again, you know what to do
NOTE: Maybe your want to replace the framework-res again, but only will work if is for your device. So i recomend that you modify your stock framework-res by yourself (you can use images or xmls from other sources to your framework-res, this should be safer) using apktool manually or a program (there are some of them in xda, choose your favorite )
Yay 50% of dell method worked, just 50% because Dell have tutorial for setting up ADB service, after it i used your tut, thanks, and believe me i will not test it NEVER again.
Acer Predator 8 GT-810 system\etc backup please!
Make a backup folder etc
Do you still need it? I can send it you tomorrow or something like that.
p8tgames said:
Do you still need it? I can send it you tomorrow or something like that.
Click to expand...
Click to collapse
hey man if u able to send me a back up. Will that solve my problem ?
I made mistake to wipe everything in my phone and now i dont have OS ( i cant start my phone) i can only enter TWRP and thats all. i can use pc to transfer files to my phone and then install the files from there , so i wonder if any1 send me back up will that save me ???
i cand find anywhere OS for acer predator gt 810
there is official avolo zip on acers' page. flash that zip and you're safe
Flash archive corrupted
Hi, I downloaded this archive and I want to flash my tablet, but Intel Phone Flash Tool Lite(flasher for x86 devices) say, that archive corrupted. I downloaded firmware 3 time, but its not working.I used TWRP to install firmware, it installed, but i have BootLoop.Please, someone, do Backup of firmware.
dvijetrecine said:
there is official avolo zip on acers' page. flash that zip and you're safe
Click to expand...
Click to collapse
Hi, I downloaded this archive and I want to flash my tablet, but Intel Phone Flash Tool Lite(flasher for x86 devices) say, that archive corrupted. I downloaded firmware 3 time, but its not working.I used TWRP to install firmware, it installed, but i have BootLoop.Please, someone, do Backup of firmware
Alex_merser54 said:
Hi, I downloaded this archive and I want to flash my tablet, but Intel Phone Flash Tool Lite(flasher for x86 devices) say, that archive corrupted. I downloaded firmware 3 time, but its not working.I used TWRP to install firmware, it installed, but i have BootLoop.Please, someone, do Backup of firmware
Click to expand...
Click to collapse
Use fastboot to flash the stock ROM instead of Intel flash tool. (If you know what you're doing, just read the part in blue below.)
fastboot is for Android devices, whether they have Qualcomm or Intel processors. Using Intel Flash tool is more akin to using Qualcomm's QPST for flashing, which is also something that should only be attempted
after trying fastboot. The Intel flash tool expects the .zip file to be in a format such as a Chuwi ROM with Windows is. Intel Flash tool unfortunately doesn't expect the .zip to be in the Android format like Acer's stock
ROM "AV0L0-something.zip" is.
With the tablet off, and plugged into your computer, hold both volume buttons and power it on. (You probably already knew this step, but here just in case )
It will vibrate longer than it usually does when turning on.
The screen should indicate that the device is in download, or "dnx" mode.
Open a command prompt in administrator mode,(the title of the window should say "Administrator: Windows Command Prompt" or "Administrator: <current directory>")
Type:
Code:
fastboot
If command not found, then either copy fastboot.exe into System32, or add the path it is in to your PATH variable, or simply navigate to its directory within the command prompt.
If you're not familiar with the PATH variable, you can just shift+right-click on fastboot.exe, click "Copy Path" and then paste it into the command prompt to use it's full path in place of simply "fastboot".
Once you're able to type "fastboot" or paste the full path and press enter and it returns the fastboot help message, type:
Code:
fastboot devices
this will either return a single line containing your device's serial number, or it will return nothing at all
If you see a serial number, you're in business.
(make sure the tablet is not low on battery before you continue):
Type:
fastboot update <path to ROM .zip>
Click to expand...
Click to collapse
This should initiate a full reflashing of the stock ROM. The tablet will reboot a couple times, you should hear/feel an even longer vibration during the process, do not touch it or unplug it from the computer until it is at the initial Google device setup screen waiting for your input.
Note that this full reflashing will also overwrite TWRP with the stock recovery.
if "fastboot devices" returns nothing at all, and also doesn't say "command not found" then do the following:
open device manager on computer, find the tablet's driver (may be under portable devices, or COM ports. sometimes under USB.)
if you can't find it, look for an "unknown device" with a yellow exclamation mark on it. If you see that, then you may not have had the driver installed in the first place. To verify, unplug the tablet from the computer
and see if the unknown device disappears from device manager.
If you were able to find the tablet in device manager, then right click and "Uninstall Device" and be sure to check the box to uninstall the driver software as well before clicking OK.
Then, unplug the tablet from your computer if you haven't already.
Download the latest driver from the same place on Acer's website that you downloaded the stock ROM from. Install the driver and restart your computer if it says it needs to.
Afterward, ensure the tablet is off and try the steps above again.
biorpg said:
Use fastboot to flash the stock ROM instead of Intel flash tool. (If you know what you're doing, just read the part in blue below.)
fastboot is for Android devices, whether they have Qualcomm or Intel processors. Using Intel Flash tool is more akin to using Qualcomm's QPST for flashing, which is also something that should only be attempted
after trying fastboot. The Intel flash tool expects the .zip file to be in a format such as a Chuwi ROM with Windows is. Intel Flash tool unfortunately doesn't expect the .zip to be in the Android format like Acer's stock
ROM "AV0L0-something.zip" is.
With the tablet off, and plugged into your computer, hold both volume buttons and power it on. (You probably already knew this step, but here just in case )
It will vibrate longer than it usually does when turning on.
The screen should indicate that the device is in download, or "dnx" mode.
Open a command prompt in administrator mode,(the title of the window should say "Administrator: Windows Command Prompt" or "Administrator: <current directory>")
Type:
If command not found, then either copy fastboot.exe into System32, or add the path it is in to your PATH variable, or simply navigate to its directory within the command prompt.
If you're not familiar with the PATH variable, you can just shift+right-click on fastboot.exe, click "Copy Path" and then paste it into the command prompt to use it's full path in place of simply "fastboot".
Once you're able to type "fastboot" or paste the full path and press enter and it returns the fastboot help message, type:
this will either return a single line containing your device's serial number, or it will return nothing at all
If you see a serial number, you're in business.
(make sure the tablet is not low on battery before you continue):
Type:
This should initiate a full reflashing of the stock ROM. The tablet will reboot a couple times, you should hear/feel an even longer vibration during the process, do not touch it or unplug it from the computer until it is at the initial Google device setup screen waiting for your input.
Note that this full reflashing will also overwrite TWRP with the stock recovery.
if "fastboot devices" returns nothing at all, and also doesn't say "command not found" then do the following:
open device manager on computer, find the tablet's driver (may be under portable devices, or COM ports. sometimes under USB.)
if you can't find it, look for an "unknown device" with a yellow exclamation mark on it. If you see that, then you may not have had the driver installed in the first place. To verify, unplug the tablet from the computer
and see if the unknown device disappears from device manager.
If you were able to find the tablet in device manager, then right click and "Uninstall Device" and be sure to check the box to uninstall the driver software as well before clicking OK.
Then, unplug the tablet from your computer if you haven't already.
Download the latest driver from the same place on Acer's website that you downloaded the stock ROM from. Install the driver and restart your computer if it says it needs to.
Afterward, ensure the tablet is off and try the steps above again.
Click to expand...
Click to collapse
Thank you, but I just entered EFI and load android.efi file, also I autorun it and reflash via recovery
After few day i find out solution how to install custom ROM to my Lenovo tablet. I think its first guide how to do it because every other guides were for TB2-X30F but not for TB2-X30L.
Installation guide:
FILES TO DOWNLOAD:
ALL FILES: https:// drive.google.com/drive/folders/1heVQAryphuXNVt5k-HsUhfRrVr9MV34D
ALL LINKS WORK ! JUST DELETE THE SPACE BEFORE drive.google.com...
1) On the tablet, at Settings, you must activate on the Developer Options the Bootloader Unlock (OEM unlocking) and USB debugging. Uncheck Verify apps over USB.
How to unlock Developer: https: //youtu.be/g5wkFAWDsg0
2) Download these files directly to your Android device, not to SD card.
a) https:// drive.google.com/file/d/1230xFbPA7DOGMhuX59yagEd6w1gNCI4o/view SuperSU-v2.79.zip (for me working only v2.79)
b) https:// drive.google.com/file/d/1vRW5RZixtNVfKbJ7nL2EUetANydfmLNg/view Gapps.zip (open_gapps-arm-7.1-micro-20180721)
b) https:// drive.google.com/file/d/13Mp8guzzOvb17s88IQyez_9reozpTNbw/view boot.img (from LiOS14-UNOFFICIAL-TB2-X30L)
3) Power off completely the tablet.
4) REMOVE SD CARD ! (because for me a part of system was installed on SD card).
5) Make sure you have a good cable so the connection between PC and tablet is perfect.
6) Download https: //drive.google.com/file/d/1XTDYs7kxagj-CXHsH_yyQnMXqYwAP_hK/view ADB and Fastboot to your PC .(here are the drivers too).
7) Unzip the zip archive and run with Administrator the apps from inside of the zip. To all the questions you must to press key Y to grant all the rights it needs.
8) Press and hold Volume up and plug in usb. Now you are in stock recovery menu.
9) From stock recovery select reboot to bootloader by using volume keys and power keys.
10) Wait about 5-10sec to tablet boot in bootloader mode. (shows lenovo logo in screen when ready)
11) Download the https:// drive.google.com/file/d/15IH55DgmD6SmlILjTukGeNcmYgUPcmCg/view recovery.img(its TWRP version for Lenovo Tab2 x30f so it wont work properly) and copy it into folder adb at local disk C (installed on step 7)
12) Run CMD with administrator and type cd C:\adb to select the adb folder.
13) In cmd type fastboot unlock-go and press enter. In case this command does not work, please try fastboot -s or fastboot oem unlock-go or fastboot oem unlock .
14) Flash recovery with command fastboot flash recovery recovery.img and then type fastboot boot recovery.img
15) From TWRP select Install and browse to emmc folder and then to your folder where you stored all files you downloaded.
(in bottom right corner you have Images... or Zips... here you can choose what type of file you want to install.
Install SuperSU-v2.79.zip
16) Now in menu select Wipe -> Advanced Wipe and check Dalvik Cache, Data and Cache. Wipe them.
17) Go back to menu and select Install. And install boot.img. At top of display check Boot and flash it.
19) Download https:// drive.google.com/file/d/1MlDxidIqLOZv_QZ91i8bsHgGdBMf7l9g/view LiOS14-UNOFFICIAL-TB2-X30L.zip and copy it into folder adb at local disk C (C:\adb).
18) Go to Menu select Advanced and open ADB Sideload. Go back to CMD on your pc and type
adb devices
If its your tablet properly connected you will see some letters and numbers and sideload. After that type
adb sideload LiOS14-UNOFFICIAL-TB2-X30L.zip
Now wait for finish the installation. If its installed corectly you will see Succesful at the top.
19) Repeate step number 15 and again install SuperSU-v2.79.zip (In installation you will see Boot image patcher)
20) Unplug your tablet from PC. And reboot it. First reboot may take 5-10 minutes and can reboot few times. DO NOT INTERRUPT THIS PROCESS.
21) After first start (set language, date..) Turn off devices.
22) Power on devices to recovery mode
(Press continuously the volume up and power key. When the screen on the tablet has started, release the power key and keep pressing the volume up key)
23) Now select again Install and install Gapps (open_gapps-arm-7.1-micro-20180721.zip). Then reboot it.
Now you have installed LiOS14-UNOFFICIAL (Android 7.1), with all stock apps(gapps) and also rooted device.
this is exactly what i was looking for 3 weeks ago. my sister asked if i could have a look at her old tablet. i managed to do it by translating myself through some russian forums. btw. does netflix work? on my sisters one it does not atm. i guess the play protect thing.
binocchio said:
this is exactly what i was looking for 3 weeks ago. my sister asked if i could have a look at her old tablet. i managed to do it by translating myself through some russian forums. btw. does netflix work? on my sisters one it does not atm. i guess the play protect thing.
Click to expand...
Click to collapse
You need to download apk from Netflix site.
https:// help.netflix.com/en/node/57688
direct link to apk
https:// netflixhelp.s3.amazonaws.com/netflix-4.16-200217-release.apk
mutrin said:
You need to download apk from Netflix site.
https:// help.netflix.com/en/node/57688
direct link to apk
https:// netflixhelp.s3.amazonaws.com/netflix-4.16-200217-release.apk
Click to expand...
Click to collapse
my sister is very grateful
Thank you very much.
What build date has this rom? Sec. patches?
Can you please post your local manifest?
Very interesting guide, unfortunately the links don't work...
Is it possible to restore them?
Tanks. Max
I think its first guide how to do it because every other guides were for TB2-X30F but not for TB2-X30L.
I have only found lineage os for x30l, can someone please link lineage (Android 7) for x30f?
The difference between L and F is that L is the sim card variant. Ive read several people getting "insert sim card" when installing L on a F tablet. So I dont want messages like this.
Thanks for this tutorial. It was possible, to upgrade this old Tablet.
Do you know, if there is anything newer version for our Lenovo?
mutrin said:
After few day i find out solution how to install custom ROM to my Lenovo tablet. I think its first guide how to do it because every other guides were for TB2-X30F but not for TB2-X30L.
Installation guide:
FILES TO DOWNLOAD:
ALL FILES: https:// drive.google.com/drive/folders/1heVQAryphuXNVt5k-HsUhfRrVr9MV34D
1) On the tablet, at Settings, you must activate on the Developer Options the Bootloader Unlock (OEM unlocking) and USB debugging. Uncheck Verify apps over USB.
How to unlock Developer: https: //youtu.be/g5wkFAWDsg0
2) Download these files directly to your Android device, not to SD card.
a) https:// drive.google.com/file/d/1230xFbPA7DOGMhuX59yagEd6w1gNCI4o/view SuperSU-v2.79.zip (for me working only v2.79)
b) https:// drive.google.com/file/d/1vRW5RZixtNVfKbJ7nL2EUetANydfmLNg/view Gapps.zip (open_gapps-arm-7.1-micro-20180721)
b) https:// drive.google.com/file/d/13Mp8guzzOvb17s88IQyez_9reozpTNbw/view boot.img (from LiOS14-UNOFFICIAL-TB2-X30L)
3) Power off completely the tablet.
4) REMOVE SD CARD ! (because for me a part of system was installed on SD card).
5) Make sure you have a good cable so the connection between PC and tablet is perfect.
6) Download https: //drive.google.com/file/d/1XTDYs7kxagj-CXHsH_yyQnMXqYwAP_hK/view ADB and Fastboot to your PC .(here are the drivers too).
7) Unzip the zip archive and run with Administrator the apps from inside of the zip. To all the questions you must to press key Y to grant all the rights it needs.
8) Press and hold Volume up and plug in usb. Now you are in stock recovery menu.
9) From stock recovery select reboot to bootloader by using volume keys and power keys.
10) Wait about 5-10sec to tablet boot in bootloader mode. (shows lenovo logo in screen when ready)
11) Download the https:// drive.google.com/file/d/15IH55DgmD6SmlILjTukGeNcmYgUPcmCg/view recovery.img(its TWRP version for Lenovo Tab2 x30f so it wont work properly) and copy it into folder adb at local disk C (installed on step 7)
12) Run CMD with administrator and type cd C:\adb to select the adb folder.
13) In cmd type fastboot unlock-go and press enter. In case this command does not work, please try fastboot -s or fastboot oem unlock-go or fastboot oem unlock .
14) Flash recovery with command fastboot flash recovery recovery.img and then type fastboot boot recovery.img
15) From TWRP select Install and browse to emmc folder and then to your folder where you stored all files you downloaded.
(in bottom right corner you have Images... or Zips... here you can choose what type of file you want to install.
Install SuperSU-v2.79.zip
16) Now in menu select Wipe -> Advanced Wipe and check Dalvik Cache, Data and Cache. Wipe them.
17) Go back to menu and select Install. And install boot.img. At top of display check Boot and flash it.
19) Download https:// drive.google.com/file/d/1MlDxidIqLOZv_QZ91i8bsHgGdBMf7l9g/view LiOS14-UNOFFICIAL-TB2-X30L.zip and copy it into folder adb at local disk C (C:\adb).
18) Go to Menu select Advanced and open ADB Sideload. Go back to CMD on your pc and type
adb devices
If its your tablet properly connected you will see some letters and numbers and sideload. After that type
adb sideload LiOS14-UNOFFICIAL-TB2-X30L.zip
Now wait for finish the installation. If its installed corectly you will see Succesful at the top.
19) Repeate step number 15 and again install SuperSU-v2.79.zip (In installation you will see Boot image patcher)
20) Unplug your tablet from PC. And reboot it. First reboot may take 5-10 minutes and can reboot few times. DO NOT INTERRUPT THIS PROCESS.
21) After first start (set language, date..) Turn off devices.
22) Power on devices to recovery mode
(Press continuously the volume up and power key. When the screen on the tablet has started, release the power key and keep pressing the volume up key)
23) Now select again Install and install Gapps (open_gapps-arm-7.1-micro-20180721.zip). Then reboot it.
Now you have installed LiOS14-UNOFFICIAL (Android 7.1), with all stock apps(gapps) and also rooted device.
Click to expand...
Click to collapse
I have followed the instructions and successfully installed LiOS14. Then, however, I have factory reset the tablet via Settings. Now it always boots to TWRP, no matter what I have tried I could not installed back the LiOS14 I only have TWRP right now.
Any help?
Boyalikus said:
I have followed the instructions and successfully installed LiOS14. Then, however, I have factory reset the tablet via Settings. Now it always boots to TWRP, no matter what I have tried I could not installed back the LiOS14 I only have TWRP right now.
Any help?
Click to expand...
Click to collapse
Same here
For me, this worked:
Lg v20 keeps booting to twerp recovery after factory reset. Megarom
Really not loving this phone and this rom. After learning I can't return to stock. Decided to factory reset it andoesn't then it boots directly to twerp recovery. Do did the first factory recovery from within the phone. Then after it booted into...
forum.xda-developers.com
The tablet can also run on LineageOS 16 which is Android 9.
As I saw that the guys in the Russian 4PDA-Forum had been able to create a LiOS16, I was able to make some adjustments and compile a ROM with most recent security patches which now runs on my good old TB2-X30L / TAB2 A10-30:
lineage-16.0-20210328-UNOFFICIAL-TB2-X30L.zip | by kenschbacher9 for 10
Download GApps, Roms, Kernels, Themes, Firmware, and more. Free file hosting for all Android developers.
androidfilehost.com
it seems that google drives are off. Can someone re-upload please?
Hallo,
I have installed LiOS14-UNOFFICIAL-TB2-X30L.zip. The installation was without problems.
But I am having problem with WiFi - problem of MAC 02:00:00:00:00:00. I have tried a lots of tips but nothig worked. Two times I was succesfull to set some MAC, but always, after while, it was gone. No able to reproduce to set.
Is it really so difficult to set somehow the MAC addres for the WiFi?
As I understand the setting of the MAC differs between different releases of OS. Does anybody know how it work in this release? It should by known where this relaese expects the MAC setting. Am I right?
1. temporary succes: Setting MAC in system/etc/firmware/wlan/qca_cld/wlan_mac.bin (I think. Its longer time ago and there was more attempts). It lasted for few months. It is not mine device so I don't know how it was handled.
2. temporary succes: I copied system/etc/firmware/wlan dir to system/vendor/firmware/wlan. I did it based on how it is in Samsung Galaxy S4 mini with Lineage 16. It worked. After restart I had to swith off and on the airplane mode to set MAC. After few attempts it was gone. No able to reproduce to set the MAC.
I am not Linux expert
nonicktoday said:
The tablet can also run on LineageOS 16 which is Android 9.
As I saw that the guys in the Russian 4PDA-Forum had been able to create a LiOS16, I was able to make some adjustments and compile a ROM with most recent security patches which now runs on my good old TB2-X30L / TAB2 A10-30:
lineage-16.0-20210328-UNOFFICIAL-TB2-X30L.zip | by kenschbacher9 for 10
Download GApps, Roms, Kernels, Themes, Firmware, and more. Free file hosting for all Android developers.
androidfilehost.com
Click to expand...
Click to collapse
Thank you very much, install your rom on my TB2-X30F and it goes very well, the only drawback that I present is that the wifi is very slow but the rom is excellent, thank you very much for your work.
palamaro said:
it seems that google drives are off. Can someone re-upload please?
Click to expand...
Click to collapse
it still work. u just need to remove the space between htttp:// AND drive.google.com...
nonicktoday said:
The tablet can also run on LineageOS 16 which is Android 9.
As I saw that the guys in the Russian 4PDA-Forum had been able to create a LiOS16, I was able to make some adjustments and compile a ROM with most recent security patches which now runs on my good old TB2-X30L / TAB2 A10-30:
lineage-16.0-20210328-UNOFFICIAL-TB2-X30L.zip | by kenschbacher9 for 10
Download GApps, Roms, Kernels, Themes, Firmware, and more. Free file hosting for all Android developers.
androidfilehost.com
Click to expand...
Click to collapse
Hi all, I've been trying to install the L16 version but I cannot install gapps or any zip from twrp. What is the procedure to install it correctly?
Boyalikus said:
I have followed the instructions and successfully installed LiOS14. Then, however, I have factory reset the tablet via Settings. Now it always boots to TWRP, no matter what I have tried I could not installed back the LiOS14 I only have TWRP right now.
Any help?
Click to expand...
Click to collapse
removing battery worked for me
Ive tried this tutorial and i bricked my tablet (i didn t backup the original firmware ) but i learned something new
for everybody who bricked their tablets lenevo tab 2 tb2 x30L do this:
1.first install Qualcomm_USB_Driver_v1.0 https://androiddatahost.com/nbyn6
2.install qfill 2.0.0.5 https://mydevfiles.com/download/qfil-tool-v2-0-0-5/
3.in qfill select flat build , progammer path is where you have your stock rom and load content same thing
4.press volume up +volume down and power button at the same time on your tablet *screen should be black*
5.press download content in qfil as soon as you connect the tablet to pc
stock firmware https://firmwarefile.com/lenovo-tab-2-tb2-x30l
^ english is not my first language so sorry for mistakes ^
[DELETED]
mutrin said:
After few day i find out solution how to install custom ROM to my Lenovo tablet. I think its first guide how to do it because every other guides were for TB2-X30F but not for TB2-X30L.
Installation guide:
FILES TO DOWNLOAD:
ALL FILES: https:// drive.google.com/drive/folders/1heVQAryphuXNVt5k-HsUhfRrVr9MV34D
ALL LINKS WORK ! JUST DELETE THE SPACE BEFORE drive.google.com...
1) On the tablet, at Settings, you must activate on the Developer Options the Bootloader Unlock (OEM unlocking) and USB debugging. Uncheck Verify apps over USB.
How to unlock Developer: https: //youtu.be/g5wkFAWDsg0
2) Download these files directly to your Android device, not to SD card.
a) https:// drive.google.com/file/d/1230xFbPA7DOGMhuX59yagEd6w1gNCI4o/view SuperSU-v2.79.zip (for me working only v2.79)
b) https:// drive.google.com/file/d/1vRW5RZixtNVfKbJ7nL2EUetANydfmLNg/view Gapps.zip (open_gapps-arm-7.1-micro-20180721)
b) https:// drive.google.com/file/d/13Mp8guzzOvb17s88IQyez_9reozpTNbw/view boot.img (from LiOS14-UNOFFICIAL-TB2-X30L)
3) Power off completely the tablet.
4) REMOVE SD CARD ! (because for me a part of system was installed on SD card).
5) Make sure you have a good cable so the connection between PC and tablet is perfect.
6) Download https: //drive.google.com/file/d/1XTDYs7kxagj-CXHsH_yyQnMXqYwAP_hK/view ADB and Fastboot to your PC .(here are the drivers too).
7) Unzip the zip archive and run with Administrator the apps from inside of the zip. To all the questions you must to press key Y to grant all the rights it needs.
8) Press and hold Volume up and plug in usb. Now you are in stock recovery menu.
9) From stock recovery select reboot to bootloader by using volume keys and power keys.
10) Wait about 5-10sec to tablet boot in bootloader mode. (shows lenovo logo in screen when ready)
11) Download the https:// drive.google.com/file/d/15IH55DgmD6SmlILjTukGeNcmYgUPcmCg/view recovery.img(its TWRP version for Lenovo Tab2 x30f so it wont work properly) and copy it into folder adb at local disk C (installed on step 7)
12) Run CMD with administrator and type cd C:\adb to select the adb folder.
13) In cmd type fastboot unlock-go and press enter. In case this command does not work, please try fastboot -s or fastboot oem unlock-go or fastboot oem unlock .
14) Flash recovery with command fastboot flash recovery recovery.img and then type fastboot boot recovery.img
15) From TWRP select Install and browse to emmc folder and then to your folder where you stored all files you downloaded.
(in bottom right corner you have Images... or Zips... here you can choose what type of file you want to install.
Install SuperSU-v2.79.zip
16) Now in menu select Wipe -> Advanced Wipe and check Dalvik Cache, Data and Cache. Wipe them.
17) Go back to menu and select Install. And install boot.img. At top of display check Boot and flash it.
19) Download https:// drive.google.com/file/d/1MlDxidIqLOZv_QZ91i8bsHgGdBMf7l9g/view LiOS14-UNOFFICIAL-TB2-X30L.zip and copy it into folder adb at local disk C (C:\adb).
18) Go to Menu select Advanced and open ADB Sideload. Go back to CMD on your pc and type
adb devices
If its your tablet properly connected you will see some letters and numbers and sideload. After that type
adb sideload LiOS14-UNOFFICIAL-TB2-X30L.zip
Now wait for finish the installation. If its installed corectly you will see Succesful at the top.
19) Repeate step number 15 and again install SuperSU-v2.79.zip (In installation you will see Boot image patcher)
20) Unplug your tablet from PC. And reboot it. First reboot may take 5-10 minutes and can reboot few times. DO NOT INTERRUPT THIS PROCESS.
21) After first start (set language, date..) Turn off devices.
22) Power on devices to recovery mode
(Press continuously the volume up and power key. When the screen on the tablet has started, release the power key and keep pressing the volume up key)
23) Now select again Install and install Gapps (open_gapps-arm-7.1-micro-20180721.zip). Then reboot it.
Now you have installed LiOS14-UNOFFICIAL (Android 7.1), with all stock apps(gapps) and also rooted device.
Click to expand...
Click to collapse
Will this work with x30F?