Huawei Y9(2019) Bootloop & FRP Lock - Android Q&A, Help & Troubleshooting

Hello guys.
I would really appreciate if you could shed some light onto my problem.
I recently acquired a Huawei Y9(2019-JKMLX3). The device is full stock, no custom recovery or root.
Also recently, right out of nowhere, the device ran out of battery, and when I tried to turn it on after a charge, I just got an awful bootloop... (Gets to the HUAWEI logo, and restarts over and over again)
Ok, i kind of know how to deal with this situations(already downloaded stock rom), but the real problem is that I can't access recovery by any means. I've tried every key combination, and nothing... Except for one time, when i did get a recovery screen, but i got FRP lock
Haven't been able to get to that screen again.
So, any recommendations? Is it dead, or is it that I'm doing something wrong.
Thanks for the support on this!

where did you get the stock firmware from?? did you resolve your issue from that time??
please share.
Thx

Related

[Q] Need help on my HTC Mozart

I got a very strange problem with my HTC Mozart.
After a night of charging, in the next morning, I got a mostly break Mozart.
It could be turned on but stuck at the logo screen. After a while (maybe 2 minutes), it will restart but still stuck at logo screen.
Condition of mine is:
- Ship ROM with jailbroken.
- Can access hard reset screen, done the hard reset but no result so far.
Could you give me some advices?
Should I proceed flash ROM or smt
Seems to like you had been messed with your rom or you are a victim of a some slutty virus. I think best thing is to do is Flash the phone and put a new rom on it. But first Remove All the unusual apps
Hope this will helpful
Thank you for your response but it's impossible to access uninstallation as I stuck at logo screen.
I don't know whether other got the same problem because I think it's all reset after Hard Reset, isn't it?
I have a same problem! plz help!

[Q] Leader Impression i10a-LE Bricked

I have an Impression i10A-LE tablet that won't bootup. When powering on the device, I get the "Leader" logo, followed by the "Impression" logo a few seconds later. The screen gets stuck on the logo.
I've tried just about every key combination that I've found others mentioning online and NONE of them get me to a recovery screen.
Does anybody have any ideas how I can restore this tablet to factory and/or re-flash it?
has anyone unbricked the leader impression i10a-le,because ive tried everything out there,for the past 2-3mounths and still
im bricked. so if anyone has been successful with the i10a-le pleeessss us know about it. thanks . I wanted to know if anyone with i10a-le had a copy of the update.zip 230mb that came up when u went to settings,about,update. If so i would really appreciate a copy.
I went to there website to try and get assistance ,but its either down or gone altogether.So any help would be very helpful. thanks.

Help needed to all advanced devs!

Hello I'm a user of a Sky Vega Iron (IM-A870)
And I need desperate help.
It's not an ordinary boot loop I wish it was, here's the story.
I rooted my phone just to let you know.
So I installed the wrong version of cwd recovery on my phone and so when I go into recovery mode the screen will turn like this.
imgurDOTcom/iOFieHG (sorry I can't you links yet cause I'm new)
But it wasn't a big deal I just didn't use it.
Now is the deal I decided to update my phone to stock kitkat that the vega devs supported themselves with vega station(the stock updating app)
And when it started installing it suddenly went into cwm.
I wasn't that worried at the moment just tried pulling the battery out and rebooting but...it started a boot loop.
I can't navigate cwm because of the way it is and I'm stuck. Is there another way to factory reset? or to get out of the loop?
Maybe a way to get rid of cwm and get back to stock recovery mode? Please help I need help until tomorrow! (personal reasons)
I searched online hours for solutions yet I can't find one.
Please help. I'm begging anyone out there.
Thank You

ZTE Nubia Z11 Max NX523J Stuck in BootLoop after V1.43 Update Failure

Hi Folks,
The Phone is stuck at Nubia Logo, and just stays there. TWRP was successfully installed and phone was rooted. Before actually loading the update package, i performed a wipe (delvik, system, data) and flashed a Stock Recovery. It prompted for Reboot which i did and the bad luck started.
Now, Vol-Up+Power boots into stock Recovery but unfortunately i do not have a backup nor an official Nubia ROM for the handset & hence can't do anything. Vol-Down+Power boots into Bootloader in which all the options pretty much take me back to Stock Recovery.
I know i made a stupid mistake but it would be really really helpful if anyone could please help put an end to my misery and undo this error. I have already tried discharging completely and then trying to power it back on again but to no avail.
Thanks in advance
Guys, a little help here please!!
My laptop does not recognize the device, it doesn't even appear when connected via USB Cable, although it charges alright.
I tried installing Nubia Recovery Tool but unfortunately it was in Chinese and I could not understand one word of it.
Please HELP!!
Hi Goraya,
I get a lot of answers from Pesa1234, hi is from Italy so his English is not that good.
I use the ComboRom 4.2 and in principle it is good, although I don't have fast charging.

anyone please help me. i just bricked my phone

the phone's model is nubia Z5s mini nx404h. the thing is this model is only sold to Philippines and Russia and its pretty outdated its jelly bean 4.3 but the thing is i rooted it. flashed the suitable TWRP for my device. and i accidentally wiped cache/dalvik then it restarted to recovery thrice even if i choose to reboot to system. the information about this device is so scarce that i had to spend 29 hours just trying to find a way to unlock the bootloader. i succeeded but now this. after certain reboots to recovery i shut it down. and tried to restart it, next thing that's happened its stuck with ZTE logo. buttons dont work. the battery cannot be removed, and its past the 2 weeks handset warranty so im doomed. now every time i try to charge it and connect it into a computer logo will show, again. and it computer says usb not recognized, then thats it. buttons not working nothing is working. please help. im trying everything, almost everything. thanks to anyone who will be kind enough to help me.

Categories

Resources