USB Debugging if you can't access settings - LG V30 Questions & Answers

I have a rooted/unlocked Verizon V30 and tried to install the Havoc OS rom on my phone. For some reason, it will not download the updates upon initial boot. It does not bootloop, it just looks like it is working on finding these updates and they never show. I wanted to access TWRP and for whatever reason I can't figure out, it will not boot into it. So without getting into android and the settings to enable usb debugging I am seriously confused on what to do next. I have also tried to do factory reset, but after hitting yes 2x, it only brings me to the same question and will not progress unless I hard reset.
If I could get usb debugging on and then push TWRP I could either flash back to what I was using or try and reinstall...
Any assistance is greatly appreciated! Thank you!

Bobert3332 said:
I have a rooted/unlocked Verizon V30 and tried to install the Havoc OS rom on my phone. For some reason it will not download the updates upon initial boot. It does not bootloop, it just looks like it is working on finding these updates and they never show.
Click to expand...
Click to collapse
I almost have no idea what you're talking about. What updates? You mean you're trying to download the Havoc ROM? Or you have it installed and you're trying to do something else?
Bobert3332 said:
I wanted to access TWRP and for whatever reason I can't figure out, it will not boot into it. So without getting into android and the settings to enable usb debugging I am seriously confused on what to do next. I have also tried to do factory reset, but after hitting yes 2x, it only brings me to the same question and will not progress unless I hard reset.
If I could get usb debugging on and then push TWRP I could either flash back to what I was using or try and reinstall...
Any assistance is greatly appreciated! Thank you!
Click to expand...
Click to collapse
What firmware are you on right now? VS996 you flashed with TWRP flashable zip? US998 20h? Havoc ROM?
If you are still on rooted stock firmware, the best way to access TWRP is what the WTF instructions recommend. Why are you trying to do it differently?
End of Section 6. Hint: it says STRONG SUGGESTION.
___
If you've done something strange and need to re-install TWRP for some reason, go see the WTF instructions again...
If by "USB debugging" you mean fastboot flash commands (because I don't understand what you are saying), Verizon firmware doesn't have fastboot flash commands. Of the North American variants, only US998 has fastboot flash commands. That's why in WTF INSTRUCTIONS you had to temporarily Frankenstein to US998 to unlock the bootloader and install TWRP.
But you should still have had TWRP unless you've done something wierd. However you've factory reset it seems.

ChazzMatt said:
I almost have no idea what you're talking about. What updates? You mean you're trying to download the Havoc ROM? Or you have it installed and you're trying to do something else?
What firmware are you on right now? VS996 you flashed with TWRP flashable zip? US998 20h? Havoc ROM?
If you are still on rooted stock firmware, the best way to access TWRP is what the WTF instructions recommend. Why are you trying to do it differently?
End of Section 6. Hint: it says STRONG SUGGESTION.
___
If you've done something strange and need to re-install TWRP for some reason, go see the WTF instructions again...
If by "USB debugging" you mean fastboot flash commands (because I don't understand what you are saying), Verizon firmware doesn't have fastboot flash commands. Of the North American variants, only US998 has fastboot flash commands. That's why in WTF INSTRUCTIONS you had to temporarily Frankenstein to US998 to unlock the bootloader and install TWRP.
But you should still have had TWRP unless you've done something wierd. However you've factory reset it seems.
Click to expand...
Click to collapse
The update is the initial boot screen on Havoc, as in when you boot android for the first time and it has you select your language. That part. Then it says it is updating, and does that indefinitely. If I could do step 6 I would, but as the title says, I cant enable usb debugging because i cant access settings. This is where I am stuck. I can no longer get into any settings besides those that come on havoc are rom specific. Does this help clarify? Sorry for the confusion. I followed the WTF as best as I could, and I believe I installed TWRP per the instructions but I cannot get back to it to save my life.

Bobert3332 said:
The update is the initial boot screen on Havoc, as in when you boot android for the first time and it has you select your language. That part. Then it says it is updating, and does that indefinitely.
If I could do step 6 I would, but as the title says, I cant enable usb debugging because i cant access settings. This is where I am stuck. I can no longer get into any settings besides those that come on havoc are rom specific. Does this help clarify? Sorry for the confusion. I followed the WTF as best as I could, and I believe I installed TWRP per the instructions but I cannot get back to it to save my life.
Click to expand...
Click to collapse
OK, so you actually installed the Havoc ROM. I thought you were possibly on stock firmware still -- either VS996 (from TWRP flashable zip) or US998. You basically have a ROM problem, so you should also post in the Havoc ROM thread.
To install Havoc ROM -- which to my knowledge is still based on LOS-16 -- you needed to be coming from Oreo blobs, meaning Oreo stock firmware or similar LOS-16 ROMs based on Oreo blobs.
You can't install LOS-16 firmware from stock Pie or LOS-17 ROMs (which are Pie blobs).
If you were EVER on stock Pie -- just to see what it was like -- you not only have to downgrade back to Oreo to run LOS-16 ROMs but you also have to run permissive kernel from now and sometimes you need to flash permissive zip to even boot:
tech_infinity said:
If the ROM doesn't boot for you then try using permissive SElinux. Use zip from here: https://zackptg5.com/android.php
Click to expand...
Click to collapse
@tech_infinity is the expert on ROMs. Maybe he can help you more.
______
What I was referring to is on stock firmware I recommend a couple of apps that will let you boot to TWRP, as long as you give them root privileges.
You can also reboot to TWRP from the Magisk Manager app, but that reboot to recovery choice is deep in the options menu. Open up Magisk Manager, look in the menu for Modules, then click on that three dots menu...
Another option is the Reboot Recovery app. Make a shortcut button on the desktop. Click on it, it says are you sure, and it boots to Recovery.

Bobert3332 said:
The update is the initial boot screen on Havoc, as in when you boot android for the first time and it has you select your language. That part. Then it says it is updating, and does that indefinitely. If I could do step 6 I would, but as the title says, I cant enable usb debugging because i cant access settings. This is where I am stuck. I can no longer get into any settings besides those that come on havoc are rom specific. Does this help clarify? Sorry for the confusion. I followed the WTF as best as I could, and I believe I installed TWRP per the instructions but I cannot get back to it to save my life.
Click to expand...
Click to collapse
Which gapps are using? Before the checking for updates screen appears, ensure you've got good internet connection / if need be take hotspot from someone who has good internet. It gets stuck for a while if you've bad internet.
Edit: One thing you could do is go back and disable internet (both wifi and mobile data) in the initial options. Then press skip all the way. It won't check for updates then. Then sideload apk of the apps @ChazzMatt recommends to reboot into recovery or if you've flashed magisk, goto modules menu, click on right top corner and select reboot to recovery. Maybe try different gapps this time

Related

[Q] Download Mode issues

So, got my V30 here, Frankensteined H931 to US998, never had basically any issues with it so far. Decided to attempt to install the TWRP flashable US998 30b from John Fawkes and that's when all hell broke loose. But I won't get into all that, here's the primary issue now:
I get Download Mode when I power the V30 off and hold Volume Up + insert USB cable (and I've done this with multiple USB cables as well as multiple USB ports), but I never get a connection to the computer anymore in that mode. Nothing, no connects at all, no sounds to indicate a connection, while the V30 shows it's in Download Mode and is waiting for a connection.
If I power it off back to TWRP (3.2.3.7, just flashed earlier as instructed because of the Pie attempt), I get all the proper connections, sounds, etc, can copy files over to the internal as well as external storage, no issues.
Normally when most people say they can't get into Download Mode it's some issue where the device won't power on into that mode when the USB cable is attached - that's not the case here as stated: it powers on and says Download Mode and waiting for a connection, but regardless of any USB cable or port there's never a connection.
I'm suspecting it's a software issue since obviously on a reboot into TWRP the USB port works exactly as expected.
Any suggestions? Because of this I'm unable to do a clean proper US998 20h KDZ flash or the 30b KDZ flash either so thankfully I did have a backup of my previous 20h Oreo install. Of course, because it's all pooched now that is effectively useless because of course of the encryption and upon restoring the backup it won't boot because of the password crap and forces me to format DATA and start all over again.
/me hates encryption when this BS happens, seriously...
So, any tips or tricks that might get me back to a working connection with Download Mode? Flashing a particular partition or something? I'm basically about to redo it with a clean 20h TWRP flashable here in a bit, not left with many other options now.
Anything is appreciated, thanks...
1) Try flashing US998 20e TWRP-FLASHABLE zip. See if that gets you download mode back.
If not, then
2) Try different LGUP.
______
After you get Download mode back, try these steps. Helpful people been testing this out...
For users with TWRP who get stuck on LG logo.
* Flash Verizon VS996 Nougat Partition DL -- EXCEPT for Recovery partitions, to keep TWRP. Do NOT choose all partitions!
You will probably lose download mode, but you've prepped your phone, corrected any partitions. (This is not just for Verizon users, this is for all North American variants -- except for T-Mobile H932.)
* Flash US99820e TWRP flashable zip to get back Download mode.
* Then REFURBISH to US998 20h KDZ.
* Now flash TWRP recovery again and then flash John's zip US99830b.
"Phone booted immediately on pie and everything is working great."
---------- Post added at 01:01 AM ---------- Previous post was at 12:58 AM ----------
rmgibbs1861 said:
ATT 931 on US998. Hangs on the LG Logo for PIE. Will there. be another release for US998 Pie? I do miss Anxious!
Click to expand...
Click to collapse
See Instructions above. Going to write something up in the US998 thread.
Yah, the 20e thing got download mode working normally meaning when the device went into that mode I'd get the traditional notification from Windows that a USB device was now attached - that's what was missing previously for whatever reason.
So I flashed 20h clean with the dev patched LGUP, no issues with Partition DL because I wanted it truly clean without anything that shouldn't be there, and that meant the factory recovery partition as well.
Then I attempted to flash the 30b KDZ, no joy, just stuck at the LG logo and I've wasted enough time on this now so, I'll just wait till some other point and maybe give it a shot in the near future.
Kinda sucks starting over totally clean but hey, this phone has worked near-perfectly since I got it in May so it'll be fine with a clean fresh start. I'm not even going to install Magisk this time, I can't think of a single reason I even need root anymore but if I do I'll worry about that a later time.
br0adband said:
Yah, the 20e thing got download mode working normally meaning when the device went into that mode I'd get the traditional notification from Windows that a USB device was now attached - that's what was missing previously for whatever reason.
So I flashed 20h clean with the dev patched LGUP, no issues with Partition DL because I wanted it truly clean without anything that shouldn't be there, and that meant the factory recovery partition as well.
Then I attempted to flash the 30b KDZ, no joy, just stuck at the LG logo and I've wasted enough time on this now so, I'll just wait till some other point and maybe give it a shot in the near future.
Kinda sucks starting over totally clean but hey, this phone has worked near-perfectly since I got it in May so it'll be fine with a clean fresh start. I'm not even going to install Magisk this time, I can't think of a single reason I even need root anymore but if I do I'll worry about that a later time.
Click to expand...
Click to collapse
You need to do the VS996 Nougat Partition DL step. It preps the phone.
This is what you need to do:
I have all the steps above. The first 20e flash was just to get Download mode back.
ChazzMatt said:
After you get Download mode back, try these steps. Helpful people been testing this out...
For users with TWRP who get stuck on LG logo.
* Flash Verizon VS996 Nougat Partition DL -- EXCEPT for Recovery partitions, to keep TWRP. Do NOT choose all partitions!
You will probably lose download mode, but you've prepped your phone, corrected any partitions. (This is not just for Verizon users, this is for all North American variants -- except for T-Mobile H932.)
* Flash US99820e TWRP flashable zip to get back Download mode.
* Then REFURBISH to US998 20h KDZ.
* Now flash TWRP recovery again and then flash John's zip US99830b.
"Phone booted immediately on pie and everything is working great."
Click to expand...
Click to collapse
Let me start firstly by saying, thank you ChazzMatt! V30 owners around the globe are incredibly fortunate to have your dedicated write-ups and support for these terrific phones. FWIW, I'm seriously impressed with the level of knowledge and your willingness to deep dive issues with folks... thanks again!
Getting to the topic however; I have the identical issue occurring with my LS998U (V30+) that I just went through the unlock process with yesterday. This morning I TWRP flashed the VS99630c ROM and everything worked A-OK except download mode. Exact same symptoms as br0adband is describing - phone appears to enter download mode as normal (though the initial "LG V30 ThinQ" boot screen appears to have replaced the bootloader warning screen?) but is not initiating the USB port for a connection at all.
Connections are established and work normally in TWRP and when booted into the OS so there appears to be something fundamentally wrong with Pie or the flash method.
I'm 99% confident it's not a PC side issue as there isn't even a connection for LGUP or drivers to fault out on.. I also tried my other US998 phone which is on dotOS and everything worked normally.
I'm about to try the TWRP flashable 20e per ChazzMatt's suggestion and will report back if I have success (or not).
Windza said:
Let me start firstly by saying, thank you ChazzMatt! V30 owners around the globe are incredibly fortunate to have your dedicated write-ups and support for these terrific phones. FWIW, I'm seriously impressed with the level of knowledge and your willingness to deep dive issues with folks... thanks again!
Click to expand...
Click to collapse
You're welcome!
Windza said:
This morning I TWRP flashed the VS99630c ROM and everything worked A-OK except download mode. Exact same symptoms as br0adband is describing - phone appears to enter download mode as normal (though the initial "LG V30 ThinQ" boot screen appears to have replaced the bootloader warning screen?) bu
I'm about to try the TWRP flashable 20e per ChazzMatt's suggestion and will report back if I have success (or not).
Click to expand...
Click to collapse
VS996 firmware doesn't have bootloader unlocked warning. Verizon never thought it would ever be unlocked.
While flashing 20e should give you download mode back, to me or seems both of you are sort of missing the point of the preliminary VS996 Nougat Partition DL flash (while omitting the Recovery partitions to keep TWRP)
Maybe in your case you don't need it -- since you made it to the other side of Pie, but that Nougat flash fixes any Partition problems. Just be sure to keep TWRP during that.
You may temporarily lose download mode again
Then TWRP-flashable zip US998 20e fix that.
Then REFURBISH to US998 20h. You'll temporarily lose TWRP at that point.
Re-Install TWRP and the three root files.
Then flash US998 30b TWRP-flashable zip.
ChazzMatt said:
While flashing 20e should give you download mode back, to me or seems both of you are sort of missing the point of the preliminary VS996 Nougat Partition DL flash (while omitting the Recovery partitions to keep TWRP)
Click to expand...
Click to collapse
While my "missing the point" is entirely possible ChazzMatt, I was under the impression that I was already AT the preliminary Nougat step after having just stepped through the Frankenstein and unlock methods?
My progression through those steps was simply;
Frankenstein per your post here; https://forum.xda-developers.com/lg...ssflashing-t3780969/post76510671#post76510671
Unlock the bootloader, install TWRP et. al. per your directions here ;https://forum.xda-developers.com/showpost.php?p=76584629&postcount=193
Upon completing these steps, Nougat is already installed at which point I figured I was ready to flash VS99630c. What am I missing here... should I have reflashed Nougat?
I didn't have any issues like others are reporting with the upgrade to 30c (TWRP flashed it flawlessly and it booted right up).
It wasn't until I decided I'm not ready for Verizon Pie (tastes gross) and went to step back to US99820h that I realised Download Mode was broken.
Is all of this not just a case of Download Mode being broken in 30c for everyone?
ChazzMatt said:
Then TWRP-flashable zip US998 20e fix that.
.
Click to expand...
Click to collapse
Yup - just as you said. 20e restored Download Mode.
ChazzMatt said:
Then flash US998 30b TWRP-flashable zip.
Click to expand...
Click to collapse
Does Download Mode work for anyone after this step or is TWRP back to a 20 series ROM the only way back to a working LGUP?
Sorry if I'm only confusing things more but I figure I'm not the only one tripping up on this... once I understand it better, I promise I'll step in and help educate other folk
It really is true about ChazzMatt's willingness to help around here.
What I never could understand is why some users, after receiving help AND successfully using it to fix their phones, don't even bother saying thank you. I'll happily spend my daily Thanks quota on helpful posts, even if they have no relevance for me at all. And I see Chazz do the same, every day. Others too, of course. But it seems some people feel being thankful is beneath them. Or something... I just don't understand it.
</rant>
Windza said:
While my "missing the point" is entirely possible ChazzMatt, I was under the impression that I was already AT the preliminary Nougat step after having just stepped through the Frankenstein and unlock methods?
My progression through those steps was simply;
Frankenstein per your post here; https://forum.xda-developers.com/lg...ssflashing-t3780969/post76510671#post76510671
Unlock the bootloader, install TWRP et. al. per your directions here ;https://forum.xda-developers.com/showpost.php?p=76584629&postcount=193
Upon completing these steps, Nougat is already installed at which point I figured I was ready to flash VS99630c. What am I missing here... should I have reflashed Nougat?
I didn't have any issues like others are reporting with the upgrade to 30c (TWRP flashed it flawlessly and it booted right up).
It wasn't until I decided I'm not ready for Verizon Pie (tastes gross) and went to step back to US99820h that I realised Download Mode was broken.
Is all of this not just a case of Download Mode being broken in 30c for everyone?
Click to expand...
Click to collapse
No, download mode isn't broken for everyone. Most people flash to Pie with no issues and download mode still works. It's when reverting to US998 Download mode seems to go away for a number of poeple (not sure how many and may depend on the LGUP used)
_______
OK, if all you wanted was for Download mode to be restored and you had no problems getting to Pie before that, then ignore what I said.
I thought you were trying to get to Pie and couldn't. In that case the workaround involves flashing Verizon VS996 Nougat -- NOT US998 Nougat like in Frankenstein -- via Partition DL mode except for Recovery partitions. That's a necessary prep stage for Pie. Both people in this thread weren't doing that. OK, so you had good reason. :silly:
THEN going to US998 20e via TWRP flashable zip, which restores Download mode. But if the goal was to get to Pie (yours wasn't) flashing 20e to get Download mode was also step zero. It was also necessary to restore Download mode so you could then flash VS996 Nougat via Partition DL mode (except for Recovery), to then flash back US998 20e TWRP flashable zip AGAIN, to then REFURBISH to US998 20h.
The VS996 Nougat part is important for those people hitting the LG logo wall.
ChazzMatt said:
No, download mode isn't broken for everyone. Most people flash to Pie with no issues and download mode still works. It's when reverting to US998 Download mode seems to go away for a number of poeple (not sure how many and may depend on the LGUP used)
Click to expand...
Click to collapse
This is good news... thanks for confirming!
I've likely done a few hundred ROM flashes and plenty of roots/unlocks in the past 15-20yrs and this was the first time I had a genuine "Oh crap" moment where a low level mode like Download Mode truly failed.
I was also having trouble getting back into TWRP (Noxx PM refused to work on 30c) which fostered a rapidly growing concern that without TWRP and Download Mode, I was effectively bricked (or at least in for a few hours of work to find a resolution).
I breathed a sigh of relief when attempting a Master Reset led me back to TWRP... I still had options!
Anyhow, it's probably fitting for me to exit this thread on the same subject I entered on by saying thank you again for the information share and willingness to help out :good:
Cheers!
ChazzMatt said:
No, download mode isn't broken for everyone. Most people flash to Pie with no issues and download mode still works. It's when reverting to US998 Download mode seems to go away for a number of poeple (not sure how many and may depend on the LGUP used)
_______
OK, if all you wanted was for Download mode to be restored and you had no problems getting to Pie before that, then ignore what I said.
I thought you were trying to get to Pie and couldn't. In that case the workaround involves flashing Verizon VS996 Nougat -- NOT US998 Nougat like in Frankenstein -- via Partition DL mode except for Recovery partitions. That's a necessary prep stage for Pie. Both people in this thread weren't doing that. OK, so you had good reason. :silly:
THEN going to US998 20e via TWRP flashable zip, which restores Download mode. But if the goal was to get to Pie (yours wasn't) flashing 20e to get Download mode was also step zero. It was also necessary to restore Download mode so you could then flash VS996 Nougat via Partition DL mode (except for Recovery), to then flash back US998 20e TWRP flashable zip AGAIN, to then REFURBISH to US998 20h.
The VS996 Nougat part is important for those people hitting the LG logo wall.
Click to expand...
Click to collapse
I lost download mode and TWRP for some reason and all I have is system recovery and nothing works in it for me . Is there anything I can do now? All I see is MTP android device.
KDZ 99820a
Hello i wanna thank all of you guys for the amazing support on this device, he LG v30 is an amazing phone just bought a US99830B , downgraded it with LGUP to oreo, unlocked bootloader in oreo and installed TWRP downloaded 99830B flasheable zip and flashed it , then i waned to try lineage 17 and flashed it in TWRP clean install booted up in android 10 but noticed lots of bugs and no WIFI, flashed modem for oreo in TWRP wifi came back up but wanted to go back to PIE restored from a backup that performed for PIE and got botloop maybe because of the incompatible modem, tried download mode, no USB activity back to TWRP restored lineage OS and im back in the system, i took your advice to flash 99820b in TWRP my download mode is back and im on oreo, my question is if i KDZ 99830B from 99820b will download mode still work even tho it doesn't when i flash stock 99830b download mode gets lost, i dont want to flash the KDZ and end up with no download mode and no TWRP and have a hard brick
Update : I have KDZ 99820a using LGUP and locked bootloader I'm back to stock is there any issues if I update to the 99830b which is the original software that the phone came with? Can I perform that update via KDZ?
SOU55 said:
Hello i wanna thank all of you guys for the amazing support on this device, he LG v30 is an amazing phone just bought a US99830B , downgraded it with LGUP to oreo, unlocked bootloader in oreo and installed TWRP downloaded 99830B flasheable zip and flashed it , then i waned to try lineage 17 and flashed it in TWRP clean install booted up in android 10 but noticed lots of bugs and no WIFI, flashed modem for oreo in TWRP wifi came back up but wanted to go back to PIE restored from a backup that performed for PIE and got botloop maybe because of the incompatible modem, tried download mode, no USB activity back to TWRP restored lineage OS and im back in the system, i took your advice to flash 99820b in TWRP my download mode is back and im on oreo, my question is if i KDZ 99830B from 99820b will download mode still work even tho it doesn't when i flash stock 99830b download mode gets lost, i dont want to flash the KDZ and end up with no download mode and no TWRP and have a hard brick
Update : I have KDZ 99820a using LGUP and locked bootloader I'm back to stock is there any issues if I update to the 99830b which is the original software that the phone came with? Can I perform that update via KDZ?
Click to expand...
Click to collapse
Losing your download mode has nothing to do with stock.
Why did you lock your bootloader back? You can run stock rooted firmware just fine and have lots of advantages like DTS surround sound stereo.
I don't understand why people lock the bootloader back just because they decide they don't want custom ROMs. The best thing to do is run rooted stock firmware, have everything you want.
ChazzMatt said:
Losing your download nose has nothing to do with stock.
Why did you lock your bootloader back? You can run stock rooted firmware just fine and have lots of advantages like DTS surround sound stereo.
I don't understand why people lock the bootloader back just because they hate custom ROMs. The best thing to do is run rooted stock firmware, have everything you want.
Click to expand...
Click to collapse
Don't get me wrong i like having rooted devices because of the endless possibilities it offers but this time mayor newer games that are coming out they have the ability to detect if you are rooted or if your bootloader has been unlocked and they kick you out of their servers, that's the main reason why i want to go full stock, and I was so afraid to do so because some people are reporting when moving from oreo to pie it creates bootloop and since I had issues when I was rooted and flashed via twrp 99830.zip download mode won't detect the USB cable only when I rolled back with LGUP to oreo downloadode started working and I KDZ oreo to have official recovery and relocked bootloader but I want pie is just I am not sure if I can go up with LGUP to pie using 99830b (which my phone originally came with pie) from 99820b
Could you please help me with the same problem with download mode on h932? I'm on stock pie now. I want to downgrade to nought but my PC not recognize phone in download mode. Thank you.
Or_dos said:
Could you please help me with the same problem with download mode on h932? I'm on stock pie now. I want to downgrade to nought but my PC not recognize phone in download mode. Thank you.
Click to expand...
Click to collapse
First try a different USB port, different cable and/or different computer. If you never rooted the phone, there is very little chance that your actual Download Mode got corrupted, and one of the above will most likely solve it (although many doubt it because it sounds too trivial).
Also, make sure you're using the latest Dual Mode Dev patched LGUP from one of ChazzMatt's ROM threads.
Next I would try the Update Recovery mode in LG Bridge (on the Update tab).
Finally, if none of those work, you can try force installing the Pie OTA using LGUP FOTA mode (doesn't require Download Mode). It's described in the thread linked below. Best to read the whole thread for context, it's just a few pages.
[H932][T-MOBILE] URL for the H932 Pie OTA file
https://forum.xda-developers.com/lg-v30/help/h932-url-h932-pie-ota-file-t3991417
Hopefully one of those will work for you. Please report your results, regardless of outcome.
Good luck to you :fingers-crossed:
TheDannemand said:
First try a different USB port, different cable and/or different computer. If you never rooted the phone, there is very little chance that your actual Download Mode got corrupted, and one of the above will most likely solve it (although many doubt it because it sounds too trivial).
Also, make sure you're using the latest Dual Mode Dev patched LGUP from one of ChazzMatt's ROM threads.
Next I would try the Update Recovery mode in LG Bridge (on the Update tab).
Finally, if none of those work, you can try force installing the Pie OTA using LGUP FOTA mode (doesn't require Download Mode). It's described in the thread linked below. Best to read the whole thread for context, it's just a few pages.
[H932][T-MOBILE] URL for the H932 Pie OTA file
https://forum.xda-developers.com/lg-v30/help/h932-url-h932-pie-ota-file-t3991417
Hopefully one of those will work for you. Please report your results, regardless of outcome.
Good luck to you :fingers-crossed:
Click to expand...
Click to collapse
I tried all things with cabels, PCs and drivers, i'm not sure but as i know LG phone in download mode should be recognized as anything, but in my case i have no any devices in the device manager. I didn't root this phone but i bought it with unlocked bootloader so it is possible that it was rooted. I tried lock bootloader but it didn't helps so i unlocked it again. Now i'm going to try to flash OTA file. Thank you so much for help.
Or_dos said:
I tried all things with cabels, PCs and drivers, i'm not sure but as i know LG phone in download mode should be recognized as anything, but in my case i have no any devices in the device manager. I didn't root this phone but i bought it with unlocked bootloader so it is possible that it was rooted. I tried lock bootloader but it didn't helps so i unlocked it again. Now i'm going to try to flash OTA file. Thank you so much for help.
Click to expand...
Click to collapse
Does Download Mode start on the phone?
Just to make sure: From Power off, press and hold VolUp while plugging in the cable. Then load LGUP. Again make sure you're using the Pie compatible LGUP from one of ChazzMatt's ROM threads.
Otherwise I'd try LG Bridge next.
As for force installing the Pie update with LGUP FOTA (the thread I linked) we've only had one confirmed case of it fixing Download Mode so far, although not many tried it yet. On Oreo we had many users confirming it, but Pie is different.
I should add that if you have working Pie, but just would like to roll back, there is a risk that the FOTA will mess up what you have. So if it doesn't fix your Download Mode, you could be worse of. Just a heads-up
TheDannemand said:
Does Download Mode start on the phone?
Just to make sure: From Power off, press and hold VolUp while plugging in the cable. Then load LGUP. Again make sure you're using the Pie compatible LGUP from one of ChazzMatt's ROM threads.
Otherwise I'd try LG Bridge next.
As for force installing the Pie update with LGUP FOTA (the thread I linked) we've only had one confirmed case of it fixing Download Mode so far, although not many tried it yet. On Oreo we had many users confirming it, but Pie is different.
I should add that if you have working Pie, but just would like to roll back, there is a risk that the FOTA will mess up what you have. So if it doesn't fix your Download Mode, you could be worse of. Just a heads-up
Click to expand...
Click to collapse
Actually the main problem is that phone doesn't recognize by PC when download mode is on the screen. I have tried to use lg bridge to recover, but anyway it reboots my phone and then my phone doesn't recognize. Now i'm trying to solve lg up error with FOTA update, it looks like wrong dll file. I'll keep you up to date.
Thank you!
Or_dos said:
Actually the main problem is that phone doesn't recognize by PC when download mode is on the screen. I have tried to use lg bridge to recover, but anyway it reboots my phone and then my phone doesn't recognize. Now i'm trying to solve lg up error with FOTA update, it looks like wrong dll file. I'll keep you up to date.
Thank you!
Click to expand...
Click to collapse
Got it! Thank you for the update.
Completely uninstall LGUP and remove all folders of it. Then install the Dual Mode LGUP from ChazzMatt's H932 ROM thread linked below, using his exact installation steps. That's important: LGUP isn't just LGUP!
[H932][STOCK][PIE]LG V30 U.S. T-Mobile H932 H93230d_00_0902.KDZ
https://forum.xda-developers.com/lg-v30/development/h932-lg-v30-s-t-mobile-h932-t3952258

I think i bricked my lgv30 trying to root it. please help me.

I was trying to unlock the bootloader and root my lg v30 (h931) or at&t v30 using this method https://forum.xda-developers.com/showpost.php?p=76584629&postcount=193
I used this method to try to get back to android 8 to root: https://forum.xda-developers.com/lg...ssflashing-t3780969/post76510671#post76510671
I used this android nougat version: https://lg-firmwares.com/downloads-file/13784/US99810d_01_0411\
and used the duel patched dev version, I can't find a link I have like 8 million tabs open right now.
What happened:
I was following everything in that guide exactly and got the the point of flashing my phone with android nougat. Everything seemed to be working find and it said it was completed successfully, now my phone isn't detected by my computer at all and my phone will not power on. LG doesn't have a recovery or fastboot mode on the v30 but normall the shortcut to it is volume down and power button and when I do that the lg v30 splash screen comes up and keeps booting over and over. If I try to boot any other way its just completely black and comes up with a not connected screen for like a frame and then goes to black again. there is also a picture but I can't make it out in the one frame It is on screen.
I know I was an idiot for thinking I could root my phone and I am really really regretting it now but if anyone has any ideas I literally will try anything at this point. Thank you so much.
I just found the think on master reset and now I am on android 7.1.2 working. I guess I will try and continue? this has been an emotional rollercoaster
legolessedd said:
I just found the think on master reset and now I am on android 7.1.2 working. I guess I will try and continue? this has been an emotional rollercoaster
Click to expand...
Click to collapse
Just read the instructions carefully in web browser. Not an app.
Yes, Master Reset is clearly in the Frankenstein instructions.
ChazzMatt said:
Just read the instructions carefully in web browser. Not an app.
Yes, Master Reset is clearly in the Frankenstein instructions.
Click to expand...
Click to collapse
yes sorry, actually im having a new issue that I can't find a solution for anywhere. I followed all the instructions for installing havoc on my lg v30 but it has been at a white spilling loading wheel for about an hour now. I know the first build can take a while but this seems a little extreme
edit, I just ran adb bootloader recovery and now im in TWRP. not sure why that didn't work last time but it worked!
legolessedd said:
yes sorry, actually im having a new issue that I can't find a solution for anywhere. I followed all the instructions for installing havoc on my lg v30 but it has been at a white spilling loading wheel for about an hour now. I know the first build can take a while but this seems a little extreme
Click to expand...
Click to collapse
Since you have a former AT&T H931 you did all the extra prep steps necessary to install LOS custom ROM for that model?
V30 CUSTOM ROMs FAQ
https://forum.xda-developers.com/showpost.php?p=79459374&postcount=2
See question number 3 of the custom ROM FAQ. H931 and H933 need a lot of extra steps to run custom ROM.
That FAQ is linked in the WTF Instructions thread.
ChazzMatt said:
since you have a former AT&T H931 you did all the extra prep steps necessary to install LOS custom ROM for that model?
https://forum.xda-developers.com/lg-v30/how-to/root-v30-t3927154
See question number 3 of the custom ROM FAQ. H931 and H933 need a lot of extra steps to run custom ROM.
Click to expand...
Click to collapse
I messed up, I totally missed that im really sorry. I have a problem then. I can send adb commands to my device but once I do that it goes away from being an adb device and I can't send the fastboot command to boot into TWRP, also in any of the states I can't get it to be recognized by lgup right now. what do I do? im really sorry
ChazzMatt said:
Just read the instructions carefully in web browser. Not an app.
Yes, Master Reset is clearly in the Frankenstein instructions.
Click to expand...
Click to collapse
sorry for another ping but do I flash it with this rom in twrp to then flash my next rom? https://forum.xda-developers.com/lg-v30/development/rom-fw-lg-v30-joan-us998-30b-twrp-t3973811
the tutorial you linked doesn't have a link to a rom that I can see, really sorry
edit: I flashed it and my phone has the lg logo on it, im going to let it boot for a while, but im worried about ending up in the same place I as stuck in before.
ChazzMatt said:
since you have a former AT&T H931 you did all the extra prep steps necessary to install LOS custom ROM for that model?
https://forum.xda-developers.com/lg-v30/how-to/root-v30-t3927154
See question number 3 of the custom ROM FAQ. H931 and H933 need a lot of extra steps to run custom ROM.
Click to expand...
Click to collapse
I think I really messed up. so the rom in the the post didn't work either so I tried to do a master reset and now I am stuck at the splash screen with that lg logo staring back at me for all eternity. all I can do is enter the master reset menu now but it doesn't do anything. my computer won't see my phone as an adb device right now and I can't enter download mode. the lg tool detects my phone but I can't select it because it is an unknown device. am I just screwed?
legolessedd said:
I can't enter download mode. the lg tool detects my phone but I can't select it because it is an unknown device. am I just screwed?
Click to expand...
Click to collapse
Have you tried entering Download mode manually before opening LGUP?
1) Go into download mode (power off completely, then hold volume up button while plugging in USB cable)
2) open patched LGUP and KDZ via REFURBISH. At this point, you would flash US998 Oreo 20h KDZ instead of trying to flash US998 30b Pie. After you recover your phone to 20h Oreo, then you can take another run at US998 Pie if you wish.
3) IF your bootloader is unlocked, it will remain unlocked. However, you will lose TWRP, since you are flashing the full KDZ.
At that point, you will then go through Section 6 of the WTF instructions again to reintall TWRP and root.

Cant boot to download mode. just goes straight to fastboot and no adb detection.

pressing the vol - before plugging in, it would show "download mode" for a spit second and go straight to fastboot mode. i cant do anything in fastboot mode since i cant get it to show on "adb devices".
i was just starting to root this V300L30p and managed to flash the h930 to unlock the bootloader. after flashing the unlock bin i waited and held the vol - button as said in the guide but the phone never boot up. i waited 30 mins or so. i tried to get to download mode and reflashed the h930 rom using dual mode LGUP partition dl but it didnt work and i just got "cant open port" i tried refurbish and it also didnt work. i tried master reset and it didnt work in trying to reflash. after a while i just couldnt access the download mode and it just goes too fast to fastboot mode.
electrical potato said:
pressing the vol - before plugging in, it would show "download mode" for a spit second and go straight to fastboot mode. i cant do anything in fastboot mode since i cant get it to show on "adb devices".
i was just starting to root this V300L30p and managed to flash the h930 to unlock the bootloader. after flashing the unlock bin i waited and held the vol - button as said in the guide but the phone never boot up. i waited 30 mins or so. i tried to get to download mode and reflashed the h930 rom using dual mode LGUP partition dl but it didnt work and i just got "cant open port" i tried refurbish and it also didnt work. i tried master reset and it didnt work in trying to reflash. after a while i just couldnt access the download mode and it just goes too fast to fastboot mode.
Click to expand...
Click to collapse
In fastboot mode, is your Bootloader unlocked?
Can you run the getvar command?
What H930 KDZ did you flash? The right one?
ChazzMatt said:
In fastboot mode, is your Bootloader unlocked?
Can you run the getvar command?
What H930 KDZ did you flash? The right one?
Click to expand...
Click to collapse
just ran get var all command. it says "unlocked_count 1" and "unlocked: yes"
i used H93020d_00_OPEN_EU_OP_0326.kdz when it was available in the first post.
edit: also ran fastboot devices, it showed : ???????????? fastboot
edit 2: ran fastboot devices again and phone turned off. did it again and got : LGH930d794576b fastboot
electrical potato said:
just ran get var all command. it says "unlocked_count 1" and "unlocked: yes"
i used H93020d_00_OPEN_EU_OP_0326.kdz when it was available in the first post.
edit: also ran fastboot devices, it showed : ???????????? fastboot
Click to expand...
Click to collapse
OK if your Bootloader is unlocked and you have fastboot, then you don't need Download mode right now.
Install TWRP, root. Follow Section 6 of the WTF instructions.
Later after you restore modem you can worry about Download mode.
ChazzMatt said:
OK then you don't need Download mode right now.
Install TWRP, root. Follow Section 6 of the WTF instructions.
Click to expand...
Click to collapse
thanks man. really eased me up in there.
ChazzMatt said:
OK if your Bootloader is unlocked and you have fastboot, then you don't need Download mode right now.
Install TWRP, root. Follow Section 6 of the WTF instructions.
Later after you restore modem you can worry about Download mode.
Click to expand...
Click to collapse
it says that "Requested download size is more than max allowed"
electrical potato said:
it says that "Requested download size is more than max allowed"
Click to expand...
Click to collapse
See the Section 7 Trouble Shooting Tips.
You're using the TWRP listedto WTF post, right?
ChazzMatt said:
See the Section 7 Trouble Shooting Tips.
You're using the TWRP listedto WTF post, right?
Click to expand...
Click to collapse
tried it on my laptop and it works perfectly
electrical potato said:
tried it on my laptop and it works perfectly
Click to expand...
Click to collapse
That is one of the Trouble Shooting Tips... Try different computer.
Welcome to the Root Club!
ChazzMatt said:
That is one of the Trouble Shooting Tips... Try different computer.
Welcome to the Root Club!
Click to expand...
Click to collapse
another problem arose. now in TWRP. wipe to format data, typed yes, and it returns with red text "failed to mount /system (unknown error 150)". same happens when i try to do a backup.
should i go to advanced wipe and change the file system of /system to others and then back to ext4?
edit: fixed by selecting ext4 in change file system. /system was showing 0mb, after redoing the file system it is now 14mb and able to be backed up
I have problem with lg v30.
It is v30 VS996 (maybe). but it was flashed US998 Pie. And now it has an error on camera and fingerprint.
I can not enter download mode to flash stock rom and bootloader is locked.
Please, tell me what should i do.
Thank you.
CuDem said:
I have problem with lg v30.
It is v30 VS996 (maybe). but it was flashed US998 Pie. And now it has an error on camera and fingerprint.
I can not enter download mode to flash stock rom and bootloader is locked.
Please, tell me what should i do.
Click to expand...
Click to collapse
Try a regular Factory Data Reset from the Settings menu, if you haven't already. If the bootloader is locked and the phone never rooted (which it sounds like) it is unlikely that the actual ROM was corrupted - though or course not impossible.
What happens when you try to enter Download mode?
I tried to reset factory in setting and it had no effect. With reset data on recovery, it showed error message.
When i enter the download mode, it show 5 dots.
I have no idea to solve this issue
CuDem said:
I tried to reset factory in setting and it had no effect. With reset data on recovery, it showed error message.
When i enter the download mode, it show 5 dots.
I have no idea to solve this issue
Click to expand...
Click to collapse
Are you saying you have TWRP (custom recovery) on your phone? With BL locked?
Factory Reset from Settings menu only works with stock recovery, and goes deeper than TWRP wipe.
If you have TWRP, you can use that to re-flash your ROM (as ZIP) and/or to re-flash laf (Download Mode, either as ZIP or as image).
Otherwise it sounds like Download Mode is there, but LGUP isn't picking it up correctly. I suggest starting over with LGUP. People often have the wrong version, since so many are floating around: Uninstall it completely, delete its folders, possibly uninstall USB driver as well. Restart Windows. Now install drivers and LGUP from scratch using the exact versions and installation steps from ChazzMatt's Pie ROM thread linked below:
[US998][STOCK][PIE]LG V30 US998 US99830b_00_0902.KDZ
https://forum.xda-developers.com/lg-v30/development/us998-lg-v30-us998-us99830a000704-kdz-t3952256
If that still doesn't do it, then try different USB port, different cable, even different computer. Some computers are not compatible with LGUP.
TheDannemand said:
Are you saying you have TWRP (custom recovery) on your phone? With BL locked?
Factory Reset from Settings menu only works with stock recovery, and goes deeper than TWRP wipe.
If you have TWRP, you can use that to re-flash your ROM (as ZIP) and/or to re-flash laf (Download Mode, either as ZIP or as image).
Otherwise it sounds like Download Mode is there, but LGUP isn't picking it up correctly. I suggest starting over with LGUP. People often have the wrong version, since so many are floating around: Uninstall it completely, delete its folders, possibly uninstall USB driver as well. Restart Windows. Now install drivers and LGUP from scratch using the exact versions and installation steps from ChazzMatt's Pie ROM thread linked below:
[US998][STOCK][PIE]LG V30 US998 US99830b_00_0902.KDZ
https://forum.xda-developers.com/lg-v30/development/us998-lg-v30-us998-us99830a000704-kdz-t3952256
If that still doesn't do it, then try different USB port, different cable, even different computer. Some computers are not compatible with LGUP.
Click to expand...
Click to collapse
No, my phone bootloader is locked then i can not install TWRP. I tried with your LGuUP you mention above but not successfully.
May i try to flash by fastboot follow this link:
https://androidforums.com/threads/flash-using-fastboot-mode.970254/
thank you
CuDem said:
No, my phone bootloader is locked then i can not install TWRP. I tried with your LGuUP you mention above but not successfully.
May i try to flash by fastboot follow this link:
https://androidforums.com/threads/flash-using-fastboot-mode.970254/
Click to expand...
Click to collapse
Thank you for the update.
I wouldn't recommend that procedure you linked. That post is five years old, for a completely different phone (LG G2), using a KDZ extractor from 2014 which probably doesn't work with today's KDZ files.
I still don't see how your Download Mode could have been damaged on an unrooted phone. I think the problem is most likely your PC or your cable.
But that aside, I say it's time to rip off the bandaid: Unlock the bootloader and put TWRP onto the phone. It's easy on US998. Follow the guide linked below.
(WTF...!) LG V30/V30+/V30S Bootloader Unlock & Root Method (With Clear Instructions)
https://forum.xda-developers.com/showpost.php?p=76584629&postcount=193
LG V30 is one of the most well documented, most rootable, and most supported phones on the planet -- largely thanks to the guy who wrote that guide. So don't look for any other solutions from anywhere else on the internet
TheDannemand said:
(WTF...!) LG V30/V30+/V30S Bootloader Unlock & Root Method (With Clear Instructions)
https://forum.xda-developers.com/showpost.php?p=76584629&postcount=193
LG V30 is one of the most well documented, most rootable, and most supported phones on the planet -- largely thanks to the guy who wrote that guide. So don't look for any other solutions from anywhere else on the internet
Click to expand...
Click to collapse
Thanks for the very kind words. :good:
TheDannemand said:
I still don't see how your Download Mode could have been damaged on an unrooted phone. I think the problem is most likely your PC or your cable.
But that aside, I say it's time to rip off the bandaid: Unlock the bootloader and put TWRP onto the phone.
Click to expand...
Click to collapse
As we discussed elsewhere, however, he would need Download mode to go back to the early Oreo firmware is he wanted to bootloader unlock and root.
There have been reports of other people losing Download mode when updating to US998 Pie -- but those were people using the TWRP flashable zip. The fix was to flash US998 20e (Oreo) TWRP flashable zip and for some reason that restored Download mode. They could then try again to update to US998 Pie if they really wished. I haven't see that reported flashing with KDZ.
The fingerprint and camera issue is also reminiscent of a V30 that was on LOS-17 (which needs a permissive kernel). Even when going back to stock firmware, you still have to run permissive. The fix for THAT problem is to refurbish to Nougat stock firmware and then update back to newer stock firmware (last Oreo which is very stable or Pie which has some issues).
But he can't do that either until he gets Download mode back.
I really don't have any suggestions.
Thank you for pointing that out, @ChazzMatt!
@CuDem: ChazzMatt is completely right. I forgot you have to use Download Mode to roll back to 20b in order to use the WTF bootloader unlock trick. Duh... So that's not a path for you to fix this.
To me it sounds like this phone WAS previously BL unlocked and rooted, and that's where the problems with Download Mode began. Or LOS-17 was installed, causing the Camera and Fingerprint issues mentioned. Maybe the previous owner re-locked the bootloader and sold the phone, pretending it was in better shape than it was?
I can think of the following:
1) If you know the history of the phone and that it was never unlocked or rooted before, then I would still say it is unlikely that its laf partition (which contains Download Mode) was actually corrupted. The phone could still have been Frankensteined incorrectly or "abused" with LGUP, but because of very thorough integrity checking when flashing through Download mode, it would rarely cause you to lose Download mode. So if you KNOW it has never been BL unlocked, I would continue trying on a different computer, with different cables, different USB ports, drivers etc. If fastboot devices returns a serial number, that's a good test that USB drivers and ADB connection is working. But you could still have LGUP issues. Again, some computers (particularly some AMD processors) are simply not compatible with LGUP.
2) See if you can find the OTA update file for US99830b and force update it using LGUP FOTA mode. This works with the phone booted into the OS and MTP (file sharing) turned on. It may not complete the update since you are already on 30b, but it will rewrite laf (Download mode) as its first step. Several H932 owners have done that back in the Oreo days, and a few have done it on Pie. Study the thread linked below for the background and the procedure. But DO NOT use the files shared in that thread, NOR ANY OTHER H932 FILES. You will brick your phone if you flash anything H932 on any other model, or vice versa.
[H932][T-MOBILE] URL for the H932 Pie OTA file
https://forum.xda-developers.com/lg-v30/help/h932-url-h932-pie-ota-file-t3991417
3) Use Qualcomm 9008 mode and the leaked firehose to rewrite the laf partition (or the entire firmware). This is a more complex procedure, which I cannot help you with, but it allows writing almost anything to the phone, and should be compatible with all V30 models EXCEPT H932. See the thread linked below, and be ready for some hard work:
LG V30 Unbrick guide (Qualcomm EDL 9008 Mode, Hardbirck, with no download mode)
https://forum.xda-developers.com/lg-v30/how-to/lg-v30-unbrick-guide-qualcomm-edl-9008-t4048661
4) Contact the XDA member from Moldova who can repair your V30 remotely for a fee. His name always escapes me, but maybe Chazz or others remember. He is also on eBay:
Remote Service Repair Unbrick LG G7 G6 V30 V35 V40 in Qualcomm Mode 9008
https://www.ebay.com/itm/Remote-Ser...794311?hash=item46994ee187:g:gd0AAOSw0qFdJi7a
And that's all I can think of. Once again, please report the outcome back here, as it may help others. Good luck to you
Edit: Oh, and then there is Update Error Recovery on the Update tab in LG Bridge, which has worked for some to fix Download mode. It also runs from inside the OS (at least initially). But I am not sure LG Bridge works with US998, let alone on Frankenstein'ed phones. Still, it's easy, so worth a try.
TheDannemand said:
To me it sounds like this phone WAS previously BL unlocked and rooted, and that's where the problems with Download Mode began. Or LOS-17 was installed, causing the Camera and Fingerprint issues mentioned. Maybe the previous owner re-locked the bootloader and sold the phone, pretending it was in better shape than it was?
Click to expand...
Click to collapse
Running this fastboot command and looking at unlock_count and lock_count can be used to determine if the phone was bootloader unlocked before...
Code:
fastboot getvar all
jptV30 said:
Running this fastboot command and looking at unlock_count and lock_count can be used to determine if the phone was bootloader unlocked before...
Click to expand...
Click to collapse
Oh yeah, right. That's a good idea if you don't know whether the phone has been rooted.

Verizon rooted/unlocked - deleted "My Verizon" system app now stuck on boot

Help!
I've had a verizon V30 I unlocked and rooted via the frankenstein method a few years ago.
I was running out of space recently and did some cursory research about 'my verizon' app and it was pretty large, so I made a titanium backup and then deleted it. Also did this for the basic 'messages' app built in.
Noticed the phone was a little laggy and having some hang issues after that so I rebooted. It's stuck on a Verizon splash screen with a few colorful dots.. seems stuck there.
I've tried clearing the cache and booting into safe mode all with the same result. I really do not want to do a factory reset.
What are my next steps for troubleshooting this or trying to restore that program? Any help is appreciated--I've tried to search a bit but not finding a good first step towards trying to resolve this.
Thanks!
water- said:
Help!
I've had a verizon V30 I unlocked and rooted via the frankenstein method a few years ago.
I was running out of space recently and did some cursory research about 'my verizon' app and it was pretty large, so I made a titanium backup and then deleted it. Also did this for the basic 'messages' app built in.
Noticed the phone was a little laggy and having some hang issues after that so I rebooted. It's stuck on a Verizon splash screen with a few colorful dots.. seems stuck there.
I've tried clearing the cache and booting into safe mode all with the same result. I really do not want to do a factory reset.
What are my next steps for troubleshooting this or trying to restore that program? Any help is appreciated--I've tried to search a bit but not finding a good first step towards trying to resolve this.
Thanks!
Click to expand...
Click to collapse
Early on with the verizon V30 roms I found that uninstalling some of the bloatware caused boot loops. From then on I just froze them; doesnt help your space situatuon though...
If no other suggestions, you could try a dirty flash of the ROM you were running (assuming you flashed TWRP zip).
I believe you'll need MyVerizon anyway, as this is what enables VOLTE and VOWIFI on Verizon (for me, at least). So I would not recommend removing it anyway.
Granted, you're past that. I would think that dirty-flashing the ROM should restore it, potentially? That could be one way to get back to running. Another way might be to reload the APK somehow. You might need to use TWRP to do that, unless there's another way to do it from a TiBu backup? If I can help in some way (I'm on VS996) I'm happy to try.
Unless you actually deleted the apps from System, it's almost certain that a Factory Reset will solve it. But I can understand your reluctance.
I'm not sure a dirty flash will help, since the problem is your data partition. You already tried deleting cache (I presume in TWRP).
And I agree that if you could somehow reload the apk, that might do it. Does ADB install work in TWRP, despite no OS? If so, that's worth trying. First pull the apks you removed from System to your computer, then run adb install apk-filename.
But FIRST make a full TWRP data backup of what you have now!
If you have to Factory Reset, you can use TiBu to restore your user apps from that backup. I haven't tried that in years, but I assume TiBu still has this feature.
Fingers crossed for you :fingers-crossed:
And for others who see this: Careful, selective debloating IS possible, but it always starts with a full backup: TWRP if rooted, otherwise LG Backup, (which saves app data and most OS settings).
Thanks all for responses, appreciated so much. In a bit of a pinch as I needed my phone for a backpacking trip last weekend, I just moved forward as best I could on Friday. Generally I tweak my phone enough to unlock/root then let it be. I guess I got greedy/complacent try trying to de-verizonify it and clear some space as much as possible.
Two things
1) Immediate solution, and still seeking some advice:
I used LGUP to flash the Android 9 kdz as an upgrade I think to the phone. Because I had TWRP as my recovery that ran into an encryption error (I subsequently saw this caveat/warning further down in one of ChazzMatt's posts), and due to that was required to wipe/clear everything.
So now I have 'benefits' of Android 9 but no root. However my bootloader is still unlocked.. so I am still seeking advice how I can get Android 9 root. Please don't tell me I have to go back to 8 and do some stuff before going back to 9 with root. I didn't actually see in any guide how to root on 9. But it is possible I missed it/just need to apply same sequence as shown as on the guide for doing so on 8.
I'm on 30c version of PIE and keep getting bugged to install a system update which I keep putting off because I'm leery of that..but I can't freeze the process without root.
Also because I flashed the stock OS, that means I lost the custom recovery, I don't have TWRP anymore (this seems so, but looking for confirmation), right?
2) retrospect, and a question for future reference
After all this I realized like an idiot I had a TWRP backup made in 2018 after I first unlocked and rooted it. Just hanging out on my SD card, which I could have accessed via TWRP before I flashed the KDZ. If I would have restored that it would have re-installed the OS and retained my data. Is that considered a dirty flash though, like it might not have worked or had subsequent problems?
And secondly on the SD card, I found all the 'dank memes' and other downloads I was worried I'd lost, so most of the data loss tragedy :silly: was averted (main pics backup to cloud, learned that lesson after lg g4 hardware bootloop pain).
water- said:
1) Immediate solution, and still seeking some advice:
I used LGUP to flash the Android 9 kdz as an upgrade I think to the phone. Because I had TWRP as my recovery that ran into an encryption error (I subsequently saw this caveat/warning further down in one of ChazzMatt's posts), and due to that was required to wipe/clear everything.
So now I have 'benefits' of Android 9 but no root. However my bootloader is still unlocked.. so I am still seeking advice how I can get Android 9 root. Please don't tell me I have to go back to 8 and do some stuff before going back to 9 with root. I didn't actually see in any guide how to root on 9. But it is possible I missed it/just need to apply same sequence as shown as on the guide for doing so on 8.
Click to expand...
Click to collapse
With unlocked bootloader on Pie, here's how you reinstall TWRP (IF you are on firmware with fastboot flash commands). Yes, I made a standalone post for this -- but if you read it it's basically just Section 6 of WTF Instructions. However, I had to make a standalone post because too many people kept thinking they had to downgrade back to Oreo, etc.
So, you can reinstall TWRP on Pie if you have unlocked bootloader. The problem is you need to fastboot flash commands to do that. VS996 firmware does not have that, which is why VS996 owners have to TEMPORARILY convert to US998 in the first place to unlock bootloader, install TWRP and root. Yes, your bootloader is already unlocked, but on VS996 you don't have the necessary fastboot flash commands to reinstall TWRP.
Thus, you will need to go back to US998 firmware (flashing KDZ via Dev Patched LGUP) to get fastboot flash commands. You can do it the hard way (US998 Pie KDZ) or you can do it the easy way (US998 Oreo KDZ). With already unlocked bootloader, you don't need to go back early Oreo, you can go to last Oreo. I don't recommend flashing US998 Pie for this, as there's too many people who have trouble with US998 Pie (stuck on LG logo, etc). You just need to temporarily get fastboot flash commands, and get TWRP reinstalled.
That post I have linked in the first sentence is for unlocked Bootloader with fastboot flash commands, on any stock firmware (Pie, Oreo, even Nougat if you wanted that for some reason).
Once you reinstall TWRP, then you can go back to VS996 Pie firmware via TWRP flashable zip.
Thanks for your response, now and two years ago.. super appreciated
I only need to get to the point to put the phone in debug mode (with access to fastboot) to get TWRP installed after flashing the recent oreo kdz. After TWRP installed follow your instructions (thanks!) to flash TWRP pie..
I'll probably give it a go this weekend or tomorrow evening, but do you have a recommended link to US998 Oreo kdz? https://androidfilehost.com/?fid=1395089523397933445 is fine?
Whereafter I'll follow your instructions for installing it (using LGUP patched) at: https://forum.xda-developers.com/lg-v30/development/us998-lg-v30-us998-us99820a040330-kdz-t3786337
In the ROM section, go to ChazzMatt's US998 Pie KDZ thread. It also has instructions for rolling back to Oreo. Follow them to the t.
Make sure to use the Pie-compatible LGUP version in there when you roll back, and install it exactly as described in that thread.
His US998 Oreo thread will have a download link for Oreo 20h (the latest Oreo). Otherwise it's easy to find on lg-firmwares.com.
Good luck to you
Ok really that was pretty easy and not bad once I got everything lined up, did it in maybe 30 minutes or less. I'm in Pie with root now and TWRP recovery. Thank you for the help!
Two points:
1) after flashing TWRP, I got some issues when wiping, I was able to flash the VS996 ROM but kept seeing some red "twrp can't mount system" or something like this. It would be a hassle but do I need to go back and reformat/reflash? or do it dirty at least?
2) maybe related to the above, maybe (probably not) not.. and I realize magisk and other avenues might cover it these days but I'm trying to debloat the TWRP flashed VS996 ROM with Titanium Backup.. stuff like NFL and slacker radio, google music.. like I did on Oreo. But Titanium keeps giving me an error about 'can't find the apk' -- Ti says I have root. I have read a bit that Android 10 really packages the apps in there so it's not like you can just remove the ones you want. is this the case for 9 too?
suggestions for alternative tool if Titanium is kind of a dinosaur in that regard?
Thanks
Well done!
1) It's best to use Format Data in TWRP to avoid that mounting error. Unless you are certain you have no mounting problems, I would recommend doing that before spending more time setting up the OS.
2) Before trying to freeze apps with TiBu, see if they can be Disabled in the regular Apps menu. Most of the "optional" bloatware can. Of course make a TWRP backup before freezing anything with TWRP!
Water-, there is already a debloated Verizon 99630c rom out there somewhere, if you would like to try it. I'm on it now.
Sorry, I can't link it. It was made by micromod777. So do a search for him.
I also use tibu, but there is another app (?) out there called migrate that backs everything up. You might look for it and try it. (I did use it a month or so ago myself just to try it - - worked for me).
water- said:
Ok really that was pretty easy and not bad once I got everything lined up, did it in maybe 30 minutes or less. I'm in Pie with root now and TWRP recovery. Thank you for the help!
Two points:
1) after flashing TWRP, I got some issues when wiping, I was able to flash the VS996 ROM but kept seeing some red "twrp can't mount system" or something like this. It would be a hassle but do I need to go back and reformat/reflash? or do it dirty at least?
Click to expand...
Click to collapse
You're welcome!
See points "f" and "g" of the screenshot. When you were installing TWRP I think you missed the "format data" part... And/or possibly the "reboot recovery" step immediately after.
If you were reading in an app (XDA or Tapatalk) instead of web browser, it's possible that section was truncated and you didn't see it.
ChazzMatt said:
You're welcome!
See points "f" and "g" of the screenshot. When you were installing TWRP I think you missed the "format data" part... And/or possibly the "reboot recovery" step immediately after.
If you were reading in an app (XDA or Tapatalk) instead of web browser, it's possible that section was truncated and you didn't see it.
Click to expand...
Click to collapse
hmmm
it's possible.. ..i definitely gave formatting a shot (hence the red errors.) and believe I rebooted to recovery.
Where I'm at now, OS booting/operating flawless (bloat aside) and root verified, can boot back into TWRP no problem...
recommended course of action?
water- said:
hmmm
it's possible.. ..i definitely gave formatting a shot (hence the red errors.) and believe I rebooted to recovery.
Where I'm at now, OS booting/operating flawless (bloat aside) and root verified, can boot back into TWRP no problem...
recommended course of action?
Click to expand...
Click to collapse
Sorry, I'm in another hemisphere for several weeks on leave of absence for family matters. Didn't see this until now. Hope you got it worked out.
ChazzMatt said:
Sorry, I'm in another hemisphere for several weeks on leave of absence for family matters. Didn't see this until now. Hope you got it worked out.
Click to expand...
Click to collapse
Not a problem at all! Maybe you mistook this post for another, as you'd fairly promptly replied to me through here over the last two weeks! much to my appreciation.
Basically I'm saying when I was doing some of the wipe functions in TWRP before flashing the new OS, and while flashing it, I saw some red mount system error messages.
However my phone is fully functional, I can reboot into TWRP recovery, I'm not noticing any functional issues with it right now.
Can I ignore because functional phone and recovery access = functioning fully! or is there some check I should do or whatnot. I mean I could clear data and start over again but It's been a week+ of customizing and getting it how I like it, kind of a hassle if it's not needed/necessary.
Thanks
water- said:
Not a problem at all! Maybe you mistook this post for another, as you'd fairly promptly replied to me through here over the last two weeks! much to my appreciation.
Basically I'm saying when I was doing some of the wipe functions in TWRP before flashing the new OS, and while flashing it, I saw some red mount system error messages.
However my phone is fully functional, I can reboot into TWRP recovery, I'm not noticing any functional issues with it right now.
Can I ignore because functional phone and recovery access = functioning fully! or is there some check I should do or whatnot. I mean I could clear data and start over again but It's been a week+ of customizing and getting it how I like it, kind of a hassle if it's not needed/necessary.
Thanks
Click to expand...
Click to collapse
Do you have encryption on? TWRP will show a mount error upon start, and prior to the passcode being entered.

How To Guide Downgrade US OEM (DE2117) Android 12 firmware to Android 11 BEFORE installing Lineage!

Lineage installation on N200 REQUIRES that you are running Android 11 or phone will soft loop after installing the Lineage boot.img
If you are updated to Android 12 firmware and want to install Lineage, you MUST downgrade first to:
DE2117 OEM Android 11 FINAL OTA
WARNING: This WILL erase all user data.
1. Place the firmware .zip file in the user root of internal phone storage.
2. Sideload OnePlus firmware Downgrade Tool on phone and use tool to flash the Android 11 firmware.
There is an Emergency Firmware install tool that OnePlus posted to the OP forum that does NOT check root status when the need to downgrade back to A11 was first acknowledged due to modem issue with first A12 OTA release.
This file was removed in a few days when they posted the official Downgrade tool replaced it.
I have used this tool to upgrade DE2117 C_16 to DE2117 C_17 while rooted and the built in upgrade tool failed at 37%.
Nice, first thanks for the hard work you're putting in. Second, is there an advantage to converting first to DE2117 then installing lineage as opposed to just installing lineage from DE2118 that you know of? I know in the other post you answered my other question stating that the Lineage will install on either so I wasn't sure if I'd get any benefit from starting over and converting my DE2118. TIA
Link575 said:
Nice, first thanks for the hard work you're putting in. Second, is there an advantage to converting first to DE2117 then installing lineage as opposed to just installing lineage from DE2118 that you know of? I know in the other post you answered my other question stating that the Lineage will install on either so I wasn't sure if I'd get any benefit from starting over and converting my DE2118. TIA
Click to expand...
Click to collapse
Lineage is using own kernel and boot.img on A11 so in the short run it is not going too make any difference, but when Lineage moves forward to A12 the OEM Firmware has newer drivers and is updated sooner, has more OEM features and bugfixes as well as no carrier bloatware.
It is possible that OP will neuter the Carrier firmware with an OTA update to prevent cross flashing device away from the Carrier rom in the next OTA update by preventing fastbootd from flashing the us oem from a carrier phone.
They have already removed fastboot boot command to boot a boot image without flashing it for test before you flash and to allow Magisk to make a backup of the original boot.img before adding Magisk.
I would convert NOW, before they decide to slam the door on this ability with a future OTA that will not allow you to downgrade and prevent this as they are under contract with the carriers to not allow this to be done.
Ok, thank you for the explanation. Guess I'll back everything up and convert it.
scanman0 said:
Lineage installation on N200 REQUIRES that you are running Android 11 or phone will soft loop after installing the Lineage boot.img
If you are updated to Android 12 firmware and want to install Lineage, you MUST downgrade first to:
DE2117 OEM Android 11 FINAL OTA
WARNING: This WILL erase all user data.
1. Place the firmware .zip file in the user root of internal phone storage.
2. Sideload OnePlus firmware Downgrade Tool on phone and use tool to flash the Android 11 firmware.
There is an Emergency Firmware install tool that OnePlus posted to the OP forum that does NOT check root status when the need to downgrade back to A11 was first acknowledged due to modem issue with first A12 OTA release.
This file was removed in a few days when they posted the official Downgrade tool replaced it.
I have used this tool to upgrade DE2117 C_16 to DE2117 C_17 while rooted and the built in upgrade tool failed at 37%.
Click to expand...
Click to collapse
This worked perfectly after following your convert guide and upgrading to 12. Downgraded back to 11 so I could install lineageOS. Thanks again!
This reddit post has a link to an English version of the downgrade apk which makes it a little easier.
keeps saying verification failed
weirdfate said:
keeps saying verification failed
Click to expand...
Click to collapse
Did you remove root (Restore boot.img) and then factory reset?
You will loose all data doing this anyway.
I m trying as well .. but stuck with verification failed message just as scanman0 I m on stock android12 no root if anyone know how to fix it ... please assit
I just downgraded. Make sure you remove root via magisk. Then proceed to rollback to Android 11. Everything worked fine. I'll install lineage tonight when I get home.
radekmazur said:
I just downgraded. Make sure you remove root via magisk. Then proceed to rollback to Android 11. Everything worked fine. I'll install lineage tonight when I get home.
Click to expand...
Click to collapse
I did not have to remove root. I used the version posted that does not check for root but maybe there's a different reason.
Does the downgrade apk have to be sideloaded via ADB?
T3CHN0T33N said:
Does the downgrade apk have to be sideloaded via ADB?
Click to expand...
Click to collapse
Just place apk in phones working directory, same path where your downloads folder is. Then install from there like any other apk and run. I also kept the FW file in the same directory but I'm not sure if that was necessary.
So, just to confirm, I press "local install" and select the firmware zip and it closes? Is the tool supposed to do anything else or am I good to flash LineageOS?
T3CHN0T33N said:
So, just to confirm, I press "local install" and select the firmware zip and it closes? Is the tool supposed to do anything else or am I good to flash LineageOS?
Click to expand...
Click to collapse
Ummm if I remember correctly hit local install and then it will prompt to point towards which FW to use. After you hit it, it will go back to the previous screen, I think verify and unpack it, then install it. Mine did appear like it was doing nothing after picking the FW and so I picked again which screwed things up so just wait after picking, it should start.
After its done it will give a message saying to restart phone I think for it to take effect, then after you restart it should ask to wipe phone, then restart again and you'd be in A11 presumably. Once in A11 your good to follow the normal procedure to install Lineage. This is all from memory though so I MAY have missed something but I don't think I did.
Link575 said:
Ummm if I remember correctly hit local install and then it will prompt to point towards which FW to use. After you hit it, it will go back to the previous screen, I think verify and unpack it, then install it. Mine did appear like it was doing nothing after picking the FW and so I picked again which screwed things up so just wait after picking, it should start.
After its done it will give a message saying to restart phone I think for it to take effect, then after you restart it should ask to wipe phone, then restart again and you'd be in A11 presumably. Once in A11 your good to follow the normal procedure to install Lineage. This is all from memory though so I MAY have missed something but I don't think I did.
Click to expand...
Click to collapse
When you say "screwed things up" what do you mean? How did it effect the install?
T3CHN0T33N said:
When you say "screwed things up" what do you mean? How did it effect the install?
Click to expand...
Click to collapse
Nothing major, caused the UI to glitch out and made it seem like the process was stuck at 81% but when I closed the app and tried to do it again it jumped to 100 and said to restart the device.
I've downgraded a second time (I'm very indecisive on which OS I want to use) and that one went as expected since I knew to give it a second to start doing its thing.
Link575 said:
Nothing major, caused the UI to glitch out and made it seem like the process was stuck at 81% but when I closed the app and tried to do it again it jumped to 100 and said to restart the device.
I've downgraded a second time (I'm very indecisive on which OS I want to use) and that one went as expected since I knew to give it a second to start doing its thing.
Click to expand...
Click to collapse
Weird, for me it just closes the app and does nothing, both the official and emergency ones. I even tried adding it to magisk's deny-list.
But I just restored the boot image via magisk (didn't restart) and it works now...
scanman0 said:
Did you remove root (Restore boot.img) and then factory reset?
You will loose all data doing this anyway.
Click to expand...
Click to collapse
Yes I factory restored the phone and tried again. Still fails every time
Has anybody had any luck figuring out the verification failed message? I too have tried both the official and emergency apps, of course I can't read the actual message in what I presume is Chinese, but it doesn't do anything and the other version says verification failed. Have not rooted. Kind of at a loss right now and all I want to do is install Lineage! I've already got my unlock token from OnePlus, but my understanding is that the phone still needs to be on A11 before installling Lineage.

Categories

Resources