Related
So we just managed to get our Huawei P9 Plus (VIE-AL10C00B106) successfully rooted
0.) *** if you have your Bootloader UNLOCK Code from Huawei, jump to STEP 3 ****
1.) downloaded DC-Unlocker, created a account, added 4 Credits(4EUR) to account. Device should have USB DEBUG Mode enabled and you need to enable 'Manufacture' mode: in dial pad type *#*#2846579#*#* - you enter the "Project Menu", go to "Background settings" -> "USB ports settings" and switch to "Manufacture mode". Dont forget to have your device Drivers (ADB) installed
2.) Once your P9 Plus is normal booted, start DC-Unlocker (here we tested 1.00.1299) , select "huawei phones" with "auto detect" and hit the Search-Button. Your device should be found and listed with IMEI, FW ect.
If you have entered your account details under "SERVER" in dc-unlocker, you can now use the "read bootloader" Button to get your bootloader unlock code - your Credits are GONE then. SAVE THIS CODE BEFORE CLOSING DC-UNLOCKER!!!!!!
3.) Boot your device in fastboot - screen should show "locked" as status on the white screen. Type command "fastboot oem unlock XXXXXXXX" (replace the XXXX with your unlock code from DC Unlocker)
4.) Phone Screen should show a WARNING Message and offer to press VOL UP to UNLOCK phone - WARNING, if you select UNLOCK and press PWR Button to agree, DEVICE WILL INSTANTLY RESETED TO MANUFACTUR DEFAULT
5.) Download the Root-SuperSU-v2.65.zip (DIRECT DOWNLOAD) and put it on a SD-Card
6.) Download the TWRP3.0.2_EMUI4.1_H95X File (DIRECT DOWNLOAD)
7.) Reboot your phone and re-enable USB DEBUG Mode, dont forget to ALLOW Debugging via PC if promped. Insert your SD-Card with the SuperSU Zip into your phone if not already done.
8.) RUN TWRP3.0.2_EMUI4.1_H95X, it will reboot your phone in Fastboot mode. By pressing 1 and then enter, you will Install TWRP 3.0.20. Follow the instructions, by pressing enter again your phone should reboot
9.) while rebooting, HOLD VOL UP and VOL DOWN together pressed until Phone tell you "booting", it should boot into TWRP now
10.) On TWRP, in the right Corner, you can Switch Language from Chinese to English (selectable, dont worry). Now go to INSTALL, move to EXT_SDCARD as source and select the SuperSU ZIP -> INSTALL
the installation of SuperSU may show mounting/unmount errors, but will be installed anyway.
After Operation is done, reboot your Phone into normal Mode. You should find SuperSU installed on your device now.
Working Firmware Versions :
VIE-AL10C00B102*
VIE-AL10C00B106
VIE-AL10C00B163
If anything goes wrong, you may RESTORE your phone to TOTAL Stock by downloading
*VIE-AL10_C00B102 (initial CN nonspecific_Android 6.0_EMUI4.1) firmware - DOWNLOAD HERE (LINK will be added later)
Put the UPDATE.APP File (~2.8GB) (content of SDupdate_Package.tar.gz) in an folder named "dload" on your MicroSD Card and reboot phone with holding VOL UP and VOL DOWN. If the Huawei Logo appears, keep Buttons pressed until DEVICE gives you a vibration impulse. Device should now completly restore initial Firmware from SD-Card. PHONE IS LOCKED again after is operation.
****** i will add Firmware Files B102(initial full release), B106(update) and B163(latest update) LATER to this thread, need to Upload them first ******
Thanks. Can Xposed work on ?
Faisal Alro8y said:
Thanks. Can Xposed work on ?
Click to expand...
Click to collapse
I flashed the framework and installed apk but it still keeps telling me "framework not running"
I'll try later again
not sure but is anyone having an issue trying to link google contacts and google calendar to the phone?
Yes, I had some problems but exported them from the web and inported them back in to the phone
Sathelp said:
Yes, I had some problems but exported them from the web and inported them back in to the phone
Click to expand...
Click to collapse
how did u do that?? so u exported it from Google contacts den used their Computer software to upload it all back in?? back there is no backup made to google moving forward yeah??
anyone knows when the international ROM will be out? i heard some variants actually allow for Google accounts to sync with the phone.
Yes, exported from the web page on my PC and put the file on my phone, then opened contacts on the phone, selected inport from the menu and imported them from the file I cresated. I found no other way at the time other than moving them to your sim card on another phone, then use that sim on your P9+
Calendar and contact sync adapter work fine here, we installed the apks I posted in the mate thread...
Does this unlock also work with the International versions for example VIE-L29 ?
Could anyone test if FlashFire works?
Guys here real TWRP with decrypt option. Chinese TWRP ****. My sources are clear and free for every one
http://forum.xda-developers.com/p9-plus/development/recovery-twrp-t3388330
Anyone could you please backup oeminfo p9 plus AL10 and share ? Thanks
Sent from my HUAWEI NXT-L29 using Tapatalk
somboons said:
Anyone could you please backup oeminfo p9 plus AL10 and share ? Thanks
Sent from my HUAWEI NXT-L29 using Tapatalk
Click to expand...
Click to collapse
Down Here:
Unzip to:
/storage/sdcard0/TWRP/BACKUPS/YOUR_SERIAL_NUMBER/2016-06-13--04-34-28_OEMinfo_A10/
Restore Backup with: TWRP
hi, i apologize for such a noob question, but i've never rooted a phone before so i'm wondering what are the benefits of rooting the Huawei P9 plus? i understand the basic gist of what rooting does and why you'd want it for phones with heavy, heavy bloat (like, say, a Samsung S5 from a US carrier). but the VIE-AL10 unit's bloatware can mostly be uninstalled (i have the china unlocked version), and with NiLS lockscreen, Nova Launcher, and the Android N theme that i got from this forum, i was able to get the phone running mostly like a normal, clean phone without any sign of those tacky Chinese bloat.
so i'm just wondering at this point what more can root do? what do you guys plan on doing, or have done, to your P9 plus after rooting?
thanks, and apologies again if this is a really dumb question for those experienced in this.
tested on L29.
Phone unlocks but I got stuck on Encryption unsuccessful loop. I did full format, but this removed the OS completely.
I have TWRP running though
Ok working unlocked rooted xposed.
Will rooting/unlocking the bootloader void the warranty or trigger some sort of counter that cannot be reset ?
How to turn phone into recovery after switching of the phone ? need to help my brother in abroad.
sam razzy said:
How to turn phone into recovery after switching of the phone ? need to help my brother in abroad.
Click to expand...
Click to collapse
Power plus volume up+ volume down.
Basically press all the buttons together.
who could help me to have the stock firmware for AL10 ?? Thanks
jvelasco said:
Down Here:
Unzip to:
/storage/sdcard0/TWRP/BACKUPS/YOUR_SERIAL_NUMBER/2016-06-13--04-34-28_OEMinfo_A10/
Restore Backup with: TWRP
Click to expand...
Click to collapse
Can you unpacke and upload only oeminfo ? I don't have P9 plus , I will add in my SRK Tool huawei.
Follow each step to install TWRP and root. I will not be responsible if you brick your device. If you follow each step you will have TWRP and root installed on your AT&T Ascend XT H1611
Updated instructions, let me know if anything needs clarifying or needs cleaning up
Step 1: Save all your data before continuing and back up your pics and files to your PC (unlocking the bootloader will wipe everything)
Step 2: Make sure to have "usb debugging" AND "enable OEM unlock" enabled from developer options in the phones settings, if you don't know how to do this here is a video since the instructions are not included in the rootmygalaxy guide below: https://www.youtube.com/watch?v=6ikbcfZfmRA Do this first!
Install adb, fastboot and usb drivers to unlock the bootloader as per the link below. Update FEB 27, 2017: when going to the link in the rootmygalaxy guide below that brings you to the Huawei unlock portal use a different browser than chrome since it keeps redirecting you to the EMUI 5.0 page. Use edge or another browser, once logged in it will bring you to the unlock page. If not and it redirects you to the EMUI 5.0 page click on "download" at the top of the page then on the next page below the search bar click on the "unlock bootloader" link which will bring you to the unlock portal. Again not working with chrome, use a different browser
http://rootmygalaxy.net/unlock-bootloader-on-huawei-devices/
By the time you are done Step 2 you should have your bootloader unlocked. **Do not continue any further if you do not**
Step 3: Download the latest TWRP.img file from here:
https://drive.google.com/file/d/0B6BmerE0MoCOdlU4RHRYT1pmeUE/view
The img must be placed in the same folder you have adb and fastboot so put it there and remember where you put it on your PC.
Step 4: Put the SuperSU zip from https://download.chainfire.eu/1019/S...0103215521.zip on your microSD card and remember where you put it.
Step 5: From windows command line with phone on and USB debugging enabled type (all adb commands below are in bold):
a) adb devices (to make sure you device is recognized)
b) adb shell reboot bootloader
Step 6: Confirm phone goes to FASTBOOT & RESCUE mode.
a) fastboot devices (to make sure you device is recognized)
b) fastboot boot TWRP.img (boots TWRP.img from Step 3)
c) Phone will boot into TWRP. Always select Keep Read Only from first screen every time you go into TWRP.
Peek around a bit if you want to, then use TWRP to backup your stock recovery to external micro SD.
d) Reboot bootloader from inside TWRP to flash this custom recovery image (no adb command this time, you are rebooting to bootloader from TWRP, you will see this option under "reboot" in TWRP).
e) fastboot flash recovery TWRP.img (now flashes TWRP recovery to the phone)
Step 7: After phone reboots, get into TWRP recovery repeating Step 6, a and b or hold power button and volume up button from power off state, then release when you see Huawei logo.
Step 8: From TWRP:
a) Once again, always select Keep Read Only from first screen every time you go into TWRP!
b) Press Settings to adjust display brightness and vibrations settings, then press home button.
c) Wipe - Format Data (Warning: You are about to blow away your files on internal storage - which you should have backed up by now. Read the red text and confirm by typing yes and blue check mark button.
d) Home - Backup - Select all six partitions, then Select Storage - Micro SDCard (very important), OK, then Swipe to Backup. When the backup is finished, Home - Advanced, File Manager, /external_sd/TWRP/BACKUPS/........ and make sure your backup files exist for each of the six partitions.
e) Home - Install then Select Storage - Micro SDCard, find your SuperSU.zip, and flash it. Swipe to confirm Flash. Be patient, as it takes a few minutes.
f) After flashing SuperSU, Wipe Dalvik and Cache, then reboot. Be patient, as it takes a few minutes. My phone rebooted several times. You should have root after your phone boots up and you set it back up!
Step 9: Be sure to make another TWRP backup of System, Data, and Boot after you get root and phone is set up again!
All credit goes to enigma2446, strtrcr_87, yuweng and divineBliss. Hopefully I cleaned the instructions up one step further since there has been a lot of questions and confusion.
Here are the old original instructions/thread for historical purposes:
https://forum.xda-developers.com/showpost.php?p=69811031&postcount=1
I'm sure that new ones are better and anyone who uses them, please leave comments/updates so they can be further improved if necessary.
You forgot to note that "enable oem unlock" must be checked under developer options.
---------- Post added at 03:22 AM ---------- Previous post was at 02:57 AM ----------
Also, should we re-clock bootloader and FRP after rooting? How is that done?
FRP? There is no known way to relock the bootloader. If you figure it out, please post how.
Gungho-sd said:
You forgot to note that "enable oem unlock" must be checked under developer options.
---------- Post added at 03:22 AM ---------- Previous post was at 02:57 AM ----------
Also, should we re-clock bootloader and FRP after rooting? How is that done?
Click to expand...
Click to collapse
Gungho-sd said:
You forgot to note that "enable oem unlock" must be checked under developer options.
Click to expand...
Click to collapse
Very good, I will add it to the guide.
Gungho-sd said:
You forgot to note that "enable oem unlock" must be checked under developer options.
---------- Post added at 03:22 AM ---------- Previous post was at 02:57 AM ----------
Also, should we re-clock bootloader and FRP after rooting? How is that done?
Click to expand...
Click to collapse
OEM unlock is in the Huawei bootloader unlock instructions. Be kind of redundant mentioning it here.
Sent from my Nexus 6P using Tapatalk
clsA said:
OEM unlock is in the Huawei bootloader unlock instructions. Be kind of redundant mentioning it here.
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
Added it as a reminder even though that is the case as you pointed out. I know how you feel clsA, 600 views and 2 thanks. It would be nice to see more appreciation to those helping out. The Ascend XT is a good phone at $100-$149 and quite a bit of work has gone into making it into a great phone. Thanks to XDA we will get there.
Let's show some appreciation to those working on this, it takes but a second to hit the "Thanks" button. No donations or money required.
I get a "E: failed to mount /data (Invalid argument)" error when I try to backup my recovery image.
bibinini said:
I get a "E: failed to mount /data (Invalid argument)" error when I try to backup my recovery image.
Click to expand...
Click to collapse
Step 8 c / Format Data
Sent from my Nexus 6P using Tapatalk
clsA said:
Step 8 c / Format Data
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
I should do that step right now even though I am on 6C, currently in the process of backing up my stock recovery? Is my stock recovery just "Recovery"? Or should I backup System as well?
bibinini said:
I should do that step right now even though I am on 6C, currently in the process of backing up my stock recovery? Is my stock recovery just "Recovery"? Or should I backup System as well?
Click to expand...
Click to collapse
no just follow the guide and ignore 0 data size
One problem with the "rootmygalaxy" instructions. Right after the line, "Boot your Huawei device into bootloader mode using the following command:" I cannot find the next breadcrumb. Where is this "bootloader mode" and how can I has one?
savannah996 said:
One problem with the "rootmygalaxy" instructions. Right after the line, "Boot your Huawei device into bootloader mode using the following command:" I cannot find the next breadcrumb. Where is this "bootloader mode" and how can I has one?
Click to expand...
Click to collapse
From a command prompt type
Adb reboot bootloader
Or
Power off
Hook phone USB to PC
Hold power and volume down
Fastboot mode is the Bootloader
Sent from my Nexus 6P using Tapatalk
clsA said:
From a command prompt type
Adb reboot bootloader
Or
Power off
Hook phone USB to PC
Hold power and volume down
Fastboot mode is the Bootloader
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
Ok I did see that "fastboot&rescuemode" screen before it says phone locked in green and frp unlock in red underneath. So I use the regular pc command prompt to enter "fastboot oem unlock your-unlock-password"? (of course I used my code) It didnt work. I imagine the "C" drive is not where the command prompt should look. haha im so computer illiterate sorry.
savannah996 said:
Ok I did see that "fastboot&rescuemode" screen before it says phone locked in green and frp unlock in red underneath. So I use the regular pc command prompt to enter "fastboot oem unlock your-unlock-password"? (of course I used my code) It didnt work. I imagine the "C" drive is not where the command prompt should look. haha im so computer illiterate sorry.
Click to expand...
Click to collapse
Does "fastboot devices" display your serial number?
The adb and fastboot commands all should be from the fastboot directory
Sent from my Nexus 6P using Tapatalk
clsA said:
Does "fastboot devices" display your serial number?
The adb and fastboot commands all should be from the fastboot directory
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
All I know is I installed the adb setup from the link in this thread but I have no icons for the program nor "adb" in my program file list or in the program file folder of "C" drive. (on my laptop running windows 8.1) here is a pic of what my screen looks like when I hold power and vol-down. https://drive.google.com/file/d/0B3TVcujYJWema01IVVZaUTlwX0tBS2NxNUYwUmxsVTltQ0I0/view?usp=sharing
savannah996 said:
All I know is I installed the adb setup from the link in this thread but I have no icons for the program nor "adb" in my program file list or in the program file folder of "C" drive. (on my laptop running windows 8.1) here is a pic of what my screen looks like when I hold power and vol-down. https://drive.google.com/file/d/0B3TVcujYJWema01IVVZaUTlwX0tBS2NxNUYwUmxsVTltQ0I0/view?usp=sharing
Click to expand...
Click to collapse
You should have an c:\adb or c:\fastboot folder
Open the command prompt from their
(Shift + right click - command prompt here)
Type
fastboot devices - hit enter
Your phone serial number should show
Next type
fastboot OEM unlock your unlock
You also want to copy the H1611.twrp.img to the adb / fastboot folder so you can boot or flash it later
Sent from my Nexus 6P using Tapatalk
Something must have not installed properly on my pc because im not seeing the folders. . Ill work on it tomorrow.
savannah996 said:
Something must have not installed properly on my pc because im not seeing the folders. . Ill work on it tomorrow.
Click to expand...
Click to collapse
Obviously adb seems to be working because you booted to the fast boot and rescue mode
If you type fastboot devices, it should return a result or you do not have fastboot installed.
Under your "local drive" whether it is "C" or something else it should be there. adb.exe and fastboot.exe should be there.
I understand this might be a little off topic, I'm very familiar with Samsung devices, just got this phone a few weeks ago. Got it rooted and Xposed running fine, just curious if anyone here has flashed suhide yet and if it works or soft bricks the phone.
Sent from my H1611 using Tapatalk
hi folks,
tomorow should be getting my hands on the Ulephone power 2.
its the 5.5 screen 4gb ram 64gb rom.
all looks good until i have seen that the normal duel sim is one is hybrid for sdcard which is the norm right,
ant
but............
usually its sim 1 is for 4g cards and the hybrid is for 2g/3g/sdcard. yeah?
well the power 2 looks like its sim slot 1 is a 2g/3g slot and the hybrid is 4g or sdcard??????????
so will have to choose 4g or sdcard??? that cant be right?
I don't try this device with sim.
I know you can use the older power (1) have a sim 4g and SD card
So i believe the power 2 have the same method.
My first steps: How to root this device? i don't find a twrp.
I try to root with kingroot kingoroot, no results
Please?
The power 2 is the same as the power wrt the sim/memory card tray; both sim slots support 4g, but only one at a time. So if you put two 4g sims in, only one of them will have 4g (you choose which one), with a sim and a memory card the 4g should default to the inserted sim, but you might have to check this in settings.
Received my power 2 a couple of weeks ago after having it on pre-order for a month and I love it (sold the original power towards the cost).
I haven't tried rooting it yet, but was thinking of trying to flash twrp for the original power and seeing if that works. The great thing about these phones is that they're very hard to brick as you can always flash them as long as they still switch on.
Slàinte
mmidders
Hello my friends. I just bought the ulefone power 2 and i try to root it. Can anyone help me pls ???
mmidders said:
The power 2 is the same as the power wrt the sim/memory card tray; both sim slots support 4g, but only one at a time. So if you put two 4g sims in, only one of them will have 4g (you choose which one), with a sim and a memory card the 4g should default to the inserted sim, but you might have to check this in settings.
Received my power 2 a couple of weeks ago after having it on pre-order for a month and I love it (sold the original power towards the cost).
I haven't tried rooting it yet, but was thinking of trying to flash twrp for the original power and seeing if that works. The great thing about these phones is that they're very hard to brick as you can always flash them as long as they still switch on.
Slàinte
mmidders
Click to expand...
Click to collapse
I'm sure it's not working the twrp from the power (1).
If you have troubles with bootloops you can flash again the facatory rom and SP flash tools.
Press the power volume + and - and SP flash tools gonna flash.
The only way is to made a twrp from the k6000 http://fvknl.pro/k6000-plus-root-guide/
I don't know how, that device is almost the same...
There has been 2 ulefone Updates since launch
Android 8.0 is scheduled for end of the year.
Updates are fine, who can create a TWRP? So we can finally root the device
geheimke said:
Updates are fine, who can create a TWRP? So we can finally root the device
Click to expand...
Click to collapse
up
TWRP please!
Not so easy to do it. It will take very long time to port or build twrp
It sucks that power 2 still doesn't have root or twrp. I refuse to touch unrooted phones. I just received it as gift. I will keep it in a drawer and check next month or so.
I find that it lacks optimisation, kinda laggy in 3D/games ..
On Antutu, scores is 44000. I tested a galaxy S5 of a friend, it was 72000. For a phone that is several years older than Power 2.
I understand that it comes not with high end cpu/gpu but still..
I will copy my post from needrom website.
I have successfully rooted my two Power 2 phones. I had to port the TWRP recovery from Oukitel k6000 plus using Carliv Image Kitchen and following some online tutorials.
The only issue is, TWRP is semi functional, that is, touch doesn't work. I had to connect a mouse to my phone via OTG usb port and using some dongle to make USB smaller to fit the port. Also it comes with Russian language as default, but can be changed to English or any other as the original TWRP from Oukitel k6000+ (3rd button from second column, then click on Globe tab at the top right then choose English and the only button at the bottom to accept the change).
I am trying to fix this with no luck so far. But at least I am rooted and I was able to flash "SR1-SuperSU-v2.82-SR1-20170608224931.zip" which is the latest as of writing this. SuperSu functions properly and I am able to use AdAway.
If anyone is interested in the recovery image, I will post it. I flashed it using fastboot though after unlocking the bootloader using "fastboot oem unlock"
Click to expand...
Click to collapse
Rebel_X said:
I will copy my post from needrom website.
Click to expand...
Click to collapse
I would very much like to give this a go with my ulefone power 2!
Here you go, TWRP for Ulefone Power 2
What you need to do before you start flashing:
0) You need to have ADB installed on your computer, if you have Windows, the easiest way is by using 15 Seconds ADB Installer v1.4.3.
1) Your bootloader must be unlocked, otherwise flashing recovery will fail using fastboot command. PLEASE NOTE: When unlocking the bootloader, your phone will do a factory reset automatically, so backup all your important files beforehand.
To unlock the bootloader:
a) Go to Settings -> About Phone -> Build number (tap on it 7 times to unlock Developer Options) -> Tap on back to Settings menu then Developer Options.
b) Now move the slider for "OEM Unlocking" to enable it, say yes to the warning message.
c) Enable "USB Debugging"
d) Connect your phone to your computer via USB cable, say Yes for the dialog on your phone to trust your computer for debugging using USB.
e) Run command prompt and type
Code:
adb reboot bootloader
Then press enter
f) Once in bootloader, type
Code:
fastboot oem unlock
Then press Volume UP on your phone to allow OEM Unlock. It shouldn't take long, just few seconds and a message will appear on command prompt saying success or OK.
g) Type
Code:
fastboot reboot
To reboot your phone, it might reboot twice, it will do a factory reset and you will have to "Enable Developer Options and USB Debugging" again. As a side note, you will also notice that OEM Unlocking is grayed out. It will remain like that unless you do "fastboot oem lock" or erase the entire phone (might erase imei, but can be restored using SN Writer Tool) and/or flash bootloader using SP_FLASH_TOOL, but I digress.
2) Before you flash TWRP recovery, you must have SuperSu zip file on your phone beforehand, otherwise, your phone will not boot to Android. It has to do with something about the original TWRP for Oukitel k6000+, since the author of that TWRP port said so in the instructions about how to flash the recovery.
So download SR1-SuperSU-v2.82-SR1-20170608224931.zip from this link or the original SuperSu thread on XDA, and copy the file into your phone, say inside the Download folder in the internal memory of your phone.
3) Open command prompt again if it is not already open, type
Code:
adb reboot bootloader
4) Once in bootloader, type
Code:
fastboot flash recovery C:\TWRP-recovery-20170618-1340.img
Note: You replace the path for the TWRP recovery to where you have the file, to make it easier, just put it in the root of C drive.
Also, if you don't already know, while in command prompt, you can type C:\TWRP then press TAB to auto-complete the file name for you, so you don't have to type lengthy file names. Keep pressing TAB to cycle between similar occurrences, that is, if you have more than one file that their names start with TWRP
5) Press power button until phone shuts down. Then press Volume UP + Power and keep holding until you see super tiny text with 3 options to cycle between. Release your fingers from Volume Up + Power, then cycle between the options using Volume Up only, choose "RECOVERY" which is the first in the menu, then press Volume DOWN to select.
6) Wait a few seconds, you will be inside TWRP, connect your phone with a mouse since touch doesn't work here. Once you do, you will see a mouse pointer appear. I used a wireless mouse with bluetooth dongle, with an adapter to change USB port size.
7) Slide the slider to the right, to enable modifications to System partition. Don't press anything else, unless you know Russian, I don't .
8) To change the language to English or your own language, click on the third button of the second column. Then click on the Globe tab on the top right corner, change language, then press the only button at the bottom to accept. Language of the UI is changed.
9) Click "Install", browse for the SuperSu zip file you have downloaded to your phone, for example inside the Download folder. And then select it.
10) Slide to the right to flash SuperSu.
11) From the TWRP menus, you can reboot your phone.
12) Enjoy your rooted Power 2 phone. :good:
---------- Post added at 04:47 AM ---------- Previous post was at 04:47 AM ----------
alpsayin said:
I would very much like to give this a go with my ulefone power 2!
Click to expand...
Click to collapse
Check the post above :good:
hello , i got a ulefone power 2 but unfortunately its not powering on. As i am from india and returning or replacing is costly and timetaking process, i need you guys to help me. I tried to flash it with software available on the website but stuck. I need some checksum.ini file which is not there in the firmware file provided. So anyone please help me. the phone doesnt even show the ulefone logo. i can just see the charging percentage when the charger is connected, then keeping it connected i tried to turn on but didnt work. keeping the charger connected ,after some time the display goes off and no mater how long you press the power button , the display doesnt show up. I can only see the notification bulb.
Soft bricked :laugh: trying to recover the phone, official ulefone guide is useless. Getting some error about a missing checksum.ini file. Will keep this thread updated
All went well until step 9, where I realised factory reset deleted the supersu zip. So I tried to reboot into system to download it again. It never booted. Doesnt even go into adb mode.
Fastboot mode and TWRP intact (TWRP needs a mouse). I was able to flash original recovery via fastboot, getting "cannot load system.img" error when I try to flash system (it appears I might need to update my adb/fastboot version).
UPDATE: was able to flash the stock rom. And tried to follow the guide again, and faced the same symptoms. If i have working TWRP, then the system doesnt boot. And vice-versa. Will keep updated, i'm a persistent mf
Rebel_X said:
Here you go, TWRP for Ulefone Power 2
What you need to do before you start flashing:
0) You need to have ADB installed on your computer, if you have Windows, the easiest way is by using 15 Seconds ADB Installer v1.4.3.
1) Your bootloader must be unlocked, otherwise flashing recovery will fail using fastboot command. PLEASE NOTE: When unlocking the bootloader, your phone will do a factory reset automatically, so backup all your important files beforehand.
To unlock the bootloader:
a) Go to Settings -> About Phone -> Build number (tap on it 7 times to unlock Developer Options) -> Tap on back to Settings menu then Developer Options.
b) Now move the slider for "OEM Unlocking" to enable it, say yes to the warning message.
c) Enable "USB Debugging"
d) Connect your phone to your computer via USB cable, say Yes for the dialog on your phone to trust your computer for debugging using USB.
e) Run command prompt and type
Code:
adb reboot bootloader
Then press enter
f) Once in bootloader, type
Code:
fastboot oem unlock
Then press Volume UP on your phone to allow OEM Unlock. It shouldn't take long, just few seconds and a message will appear on command prompt saying success or OK.
g) Type
Code:
fastboot reboot
To reboot your phone, it might reboot twice, it will do a factory reset and you will have to "Enable Developer Options and USB Debugging" again. As a side note, you will also notice that OEM Unlocking is grayed out. It will remain like that unless you do "fastboot oem lock" or erase the entire phone (might erase imei, but can be restored using SN Writer Tool) and/or flash bootloader using SP_FLASH_TOOL, but I digress.
2) Before you flash TWRP recovery, you must have SuperSu zip file on your phone beforehand, otherwise, your phone will not boot to Android. It has to do with something about the original TWRP for Oukitel k6000+, since the author of that TWRP port said so in the instructions about how to flash the recovery.
So download SR1-SuperSU-v2.82-SR1-20170608224931.zip from this link or the original SuperSu thread on XDA, and copy the file into your phone, say inside the Download folder in the internal memory of your phone.
3) Open command prompt again if it is not already open, type
Code:
adb reboot bootloader
4) Once in bootloader, type
Code:
fastboot flash recovery C:\TWRP-recovery-20170618-1340.img
Note: You replace the path for the TWRP recovery to where you have the file, to make it easier, just put it in the root of C drive.
Also, if you don't already know, while in command prompt, you can type C:\TWRP then press TAB to auto-complete the file name for you, so you don't have to type lengthy file names. Keep pressing TAB to cycle between similar occurrences, that is, if you have more than one file that their names start with TWRP
5) Press power button until phone shuts down. Then press Volume UP + Power and keep holding until you see super tiny text with 3 options to cycle between. Release your fingers from Volume Up + Power, then cycle between the options using Volume Up only, choose "RECOVERY" which is the first in the menu, then press Volume DOWN to select.
6) Wait a few seconds, you will be inside TWRP, connect your phone with a mouse since touch doesn't work here. Once you do, you will see a mouse pointer appear. I used a wireless mouse with bluetooth dongle, with an adapter to change USB port size.
7) Slide the slider to the right, to enable modifications to System partition. Don't press anything else, unless you know Russian, I don't .
8) To change the language to English or your own language, click on the third button of the second column. Then click on the Globe tab on the top right corner, change language, then press the only button at the bottom to accept. Language of the UI is changed.
9) Click "Install", browse for the SuperSu zip file you have downloaded to your phone, for example inside the Download folder. And then select it.
10) Slide to the right to flash SuperSu.
11) From the TWRP menus, you can reboot your phone.
12) Enjoy your rooted Power 2 phone. :good:
---------- Post added at 04:47 AM ---------- Previous post was at 04:47 AM ----------
Check the post above :good:
Click to expand...
Click to collapse
mbs.yaswanth said:
hello , i got a ulefone power 2 but unfortunately its not powering on. As i am from india and returning or replacing is costly and timetaking process, i need you guys to help me. I tried to flash it with software available on the website but stuck. I need some checksum.ini file which is not there in the firmware file provided. So anyone please help me. the phone doesnt even show the ulefone logo. i can just see the charging percentage when the charger is connected, then keeping it connected i tried to turn on but didnt work. keeping the charger connected ,after some time the display goes off and no mater how long you press the power button , the display doesnt show up. I can only see the notification bulb.
Click to expand...
Click to collapse
Yeah, I had the same issue with the software that comes from Ulefone, it was asking for Checksum Generator that I have to download separately, it was like 150kb stand alone executable, you put it in the same folder of your stock ROM and wait forever for it to build the Checksum, which unfortunately didn't work since it complains about multiple RECOVRY images. So scratch that.
What you need to do, is as I did, download SP FLASH TOOL, it works great, no shinanigans or bullsh!t. It flashed the stock ROM in less than 2 minutes (around 1:30 seconds, to be exact) and revived my phone. There are plenty of youtube tutorials on how to use it. It is easy, just load the scatter file, for the other file, you can use the same all in one mtk file that comes with SP FLash Tool (I did this) or use the one from your STOCK ROM.
I hope that helps :good:
---------- Post added at 02:33 PM ---------- Previous post was at 02:27 PM ----------
alpsayin said:
Soft bricked :laugh: trying to recover the phone, official ulefone guide is useless. Getting some error about a missing checksum.ini file. Will keep this thread updated
All went well until step 9, where I realised factory reset deleted the supersu zip. So I tried to reboot into system to download it again. It never booted. Doesnt even go into adb mode.
Fastboot mode and TWRP intact (TWRP needs a mouse). I was able to flash original recovery via fastboot, getting "cannot load system.img" error when I try to flash system (it appears I might need to update my adb/fastboot version).
UPDATE: was able to flash the stock rom. And tried to follow the guide again, and faced the same symptoms. If i have working TWRP, then the system doesnt boot. And vice-versa. Will keep updated, i'm a persistent mf
Click to expand...
Click to collapse
All I can think of, you did something wrong. Initially, while I was trying to port TWRP, I had the same issue, I was trying to save some steps by flashing the recovery after I unlocked the bootloader without rebooting, the result was TWRP was not able to see any partitions.
Flash Stock-ROM and redo the steps. If you flash the preloader you might have to OEM Unlock your phone again.
I mentioned that if you "do not flash SuperSu, the system will NOT boot to Android". Also mentioned that after you unlock the bootloader, you have to RE-ENABLE USB Debugging, and while you are at it, check to see if your bootloader is unlocked inside Developer Options.
Edit: BTW, try not to unlock the bootloader if it is already unlocked. If it is unlocked, then skip the steps for unlocking the bootloader. It might cause an issue.
These are the steps I used to flash TWRP and I was able to flash SuperSu, all rooted apps are working fine, AdAway, Lucky Patcher...etc!
This:
Rebel_X said:
Here you go, TWRP for Ulefone Power 2
2) Before you flash TWRP recovery, you must have SuperSu zip file on your phone beforehand, otherwise, your phone will not boot to Android. It has to do with something about the original TWRP for Oukitel k6000+, since the author of that TWRP port said so in the instructions about how to flash the recovery.
Click to expand...
Click to collapse
And this combined:
Rebel_X said:
Here you go, TWRP for Ulefone Power 2
9) Click "Install", browse for the SuperSu zip file you have downloaded to your phone, for example inside the Download folder. And then select it.
Click to expand...
Click to collapse
Apparently if you dont flash the supersu first time you go into TWRP then it gets messy. Got the root working now. Thank you for the help and of course for the TWRP build!
Also if anyone's wondering it's possible to restore the system via fastboot. Extract the rom zip (can be downloaded from http:/ulefone.com/download/power2.html ) and flash boot, recovery and system;
Code:
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
link for sp flash tool u used.
Rebel_X said:
Yeah, I had the same issue with the software that comes from Ulefone, it was asking for Checksum Generator that I have to download separately, it was like 150kb stand alone executable, you put it in the same folder of your stock ROM and wait forever for it to build the Checksum, which unfortunately didn't work since it complains about multiple RECOVRY images. So scratch that.
What you need to do, is as I did, download SP FLASH TOOL, it works great, no shinanigans or bullsh!t. It flashed the stock ROM in less than 2 minutes (around 1:30 seconds, to be exact) and revived my phone. There are plenty of youtube tutorials on how to use it. It is easy, just load the scatter file, for the other file, you can use the same all in one mtk file that comes with SP FLash Tool (I did this) or use the one from your STOCK ROM.
I hope that helps :good:
---------- Post added at 02:33 PM ---------- Previous post was at 02:27 PM ----------
All I can think of, you did something wrong. Initially, while I was trying to port TWRP, I had the same issue, I was trying to save some steps by flashing the recovery after I unlocked the bootloader without rebooting, the result was TWRP was not able to see any partitions.
Flash Stock-ROM and redo the steps. If you flash the preloader you might have to OEM Unlock your phone again.
I mentioned that if you "do not flash SuperSu, the system will NOT boot to Android". Also mentioned that after you unlock the bootloader, you have to RE-ENABLE USB Debugging, and while you are at it, check to see if your bootloader is unlocked inside Developer Options.
Edit: BTW, try not to unlock the bootloader if it is already unlocked. If it is unlocked, then skip the steps for unlocking the bootloader. It might cause an issue.
These are the steps I used to flash TWRP and I was able to flash SuperSu, all rooted apps are working fine, AdAway, Lucky Patcher...etc!
Click to expand...
Click to collapse
ok what should i select there? formal all+download or download only or firmware upgarade???
IMPORTANT: It appearance that Huawei is no longer going to provide bootloader unlocking services for their devices. Because of this, this guide is of no use unless you can find a way to get a code or you just held onto the code.
Hello, this is a guide for unlocking the bootloader and rooting the Huawei Ascend XT. I am writing this because the current guide is not very well written and does not contain bootloader unlock instructions. This will be split into two parts: Part 1, unlocking the bootloader, and Part 2, rooting the phone.
PLEASE NOTE THAT FOLLOWING THESE INSTRUCTIONS WILL WIPE YOUR DEVICE. I AM NOT RESPONSIBLE FOR AND DAMAGE DONE TO YOUR PHONE!
THINGS YOU WILL NEED:
1. A Huawei Ascend XT with at least 60% of battery left
2. A computer with adb drivers, fastboot drivers, and the Huawei USB drivers
3. A Micro-SD card for your backups (THIS IS VERY IMPORTANT! PLEASE MAKE BACKUPS!)
4. TWRP for this phone. This can be found here: https://forum.xda-developers.com/android/general/huawei-ascend-xt-h1611-t3507933 (credits to enigma2446)
5. The ZIP containing SuperSU. This can be found here: https://forum.xda-developers.com/android/general/huawei-ascend-xt-h1611-t3507933
6. The SDK Platform Tools. These can be found on the android studio website.
PART 1: UNLOCKING THE BOOTLOADER1. Geting the Bootloader Unlock Code: You need to get your bootloader unlock code. You can get this by going to https://emui.huawei.com/en/plugin.php?id=unlock
(EDIT: It appears that this website is down. I have read that if you PM Huawei on Twitter or call them and provide all the details of your phone, they will give you a code. I have not tested this method, bit people have said it worked with the mate 10.) and signing into your Huawei ID. If you dont have one, create one. Then, follow the instructions given to you by Huawei to get the code.
2. Enabling the Enable OEM Unlock Option: To enable this option, you must enable developer options. To do this, go to Settings>About Phone and tap the Build number until it says "You are now a Developer". back out of About Phone, and go to Developer options. turn on "Enable OEM unlock" and press Enable.
3. Enable USB Debugging: While you are still in Developer options, enable the option 'USB debugging" and press OK.
4. Booting Into the Bootloader: once you have completed the first three steps, you can now boot into the bootloader. Connect your phone to your computer, and open the Platform Tools folder you should have downloaded and extracted. Shift-Right click, and press "Open Command Window Here" or "Open Powershell Window Here", depending on your version of windows. Once it is open, make sure your device is detected by typing "adb devices". If it displays your device, you are good to continue. If not, something is not set up right on your computer or phone. Once you verified that your phone is detected, type "adb reboot bootloader".
5. Unlocking the Bootloader: Once your phone has booted into the bootloader, you can now unlock the bootloader. YOUR PHONE WILL BE WIPED ONCE YOU TYPED THIS COMMAND. You can unlock it by typing "fastboot oem unlock <your bootloader unlock code>". Once it has finished, you can reboot your phone, and just run through the setup fast, because you will still have to wipe it again.
PART 2: ROOTING YOUR PHONE1. Move the TWRP image you downloaded (called
Xtrecovery) to your Platform Tools folder and rename it to "TWRP.img"
2. Insert Your Micro-SD Card
3. Move the SuperSU Zip you downloaded to the SD card
4. Re-Enable USB Debugging: Enable Developer options by going to Settings>About Phone and taping the Build number until it says "You are now a Developer". Back out of About Phone, and go to Developer options, and enable USB debugging, and press OK.
5. Boot Into the Bootloader: Type "adb reboot bootloader" into your open CMD window or Powershell window.
6. Verify That your Phone says that the Bootloader is unlocked
7. Type "fastboot boot TWRP.img"
8. TWRP should boot. Tap "Keep Read Only"
9. You should now be in TWRP. Go to Backup>Select Storage and choose your Micro-SD card and tap OK. Uncheck everything and check "Recovery". Then, Swipe the slider to back up your stock recovery partition.
10. Once it has finished backing up, reboot your phone to the bootloader.
11. Once it is in the bootloader, type "fastboot flash recovery TWRP.img" to flash TWRP as your recovery. (I believe this is the point where your warrenty will be invalidated by Huawei, so be careful.)
12. When it finishes flashing TWRP, reboot your phone to TWRP by holding down the power button and volume up
13. It should boot to TWRP. Tap "Keep Read Only", then go to (YOU ARE ABOUT TO WIPE IT AGAIN)Wipe>Format Data and type yes, and hit the enter button.
14. Once it finishes, go to Backup>Select Storage, select your SD card and hit OK, then check every box to backup all six partitions, and swipe to back them up. (At the end, it may seem to get stuck at 98-99%, DO NOT STOP IT! It is generating an MD5 checksum)
15. When it finishes backing everything up, go back to the home screen of TWRP, then go to Install, navigate to where you stored the SuperSU ZIP, select it, then swipe to flash it.
16. When it finishes flashing the SuperSU ZIP, tap "Clear Cache/Dalvik" and swipe to clear them.
17. Reboot your phone. IT WILL REBOOT MULTIBLE TIMES AND APPEAR TO BE STUCK SOMETIMES, BUT DONT TOUCH IT! This is normal and it will eventually boot like normal.
That's it!
Your phone should now be rooted and have SuperSU installed. Please note that this is a Systemless root, and will be removed if you factory reset your phone.Thanks to divineBliss for creating the original instructions.
What do we do after we get root to install custom ROMS? please advise
nedfred0 said:
What do we do after we get root to install custom ROMS? please advise
Click to expand...
Click to collapse
To install a custom ROM, you need the ROM you want to install, gapps depending on the ROM, and the proper firmware. The firmware you are on can be found under about phone and is the last 4 digets of the build number (in the format of B1xx). Once you are on the proper firmware, have your ROM and other things it may require, (every ROM is different), and a backup (just in case), you can flash the ROM from TWRP. Follow the instructions provided by the creator of the ROM to properly flash it.
Where do you get the USB driver at because I am not seeing it at http://consumer.huawei.com/us/support/phones/ascend-xt/
BTJustice said:
Where do you get the USB driver at because I am not seeing it at
Click to expand...
Click to collapse
The drivers come with HiSuite. Download it and you should be good to go.
randomness725 said:
The drivers come with HiSuite. Download it and you should be good to go.
Click to expand...
Click to collapse
Thanks. I tried that but couldn't get it to go so I downloaded these instead which did the job:
https://www.androidfilehost.com/?fid=817550096634745788
does this work on the new h1711 huawei assend xt2
xaneth201 said:
does this work on the new h1711 huawei assend xt2
Click to expand...
Click to collapse
It will not. The TWRP recovery image is device specific and might brick your device if you flash it to your phone.
bricked 1711
randomness725 said:
It will not. The TWRP recovery image is device specific and might brick your device if you flash it to your phone.
Click to expand...
Click to collapse
Well I did not see that, so yeah, I have bricked it. IT comes up and says it is unlocked, it used to sit there then boot into the system.
So I downloaded the TWRP, tried to reboot to recovery and nothing.
Now, it just gets to the yellow warning screen, then goes black. Just bought this today on a black friday sale for 49.00
But did it for a reason. Now I would like to be able to recover it....
I was able to run adb and fastboot, so know that the drivers work, but it looks like it won't even get there now.
And it won't even go to the recovery, so I guess this phone is a real brick.
Can't seem to get the back cover off to remove the battery either.
You need a copy of the stock H1711 recovery image to use
"fastboot flash recovery H1711-stock-recovery.img" to restore the stock recovery. Until someone creates a working H1711 TWRP, I don't know where you'll find a stock H1711 recovery image file.
scrungydoolittle said:
Well I did not see that, so yeah, I have bricked it. IT comes up and says it is unlocked, it used to sit there then boot into the system.
So I downloaded the TWRP, tried to reboot to recovery and nothing.
Now, it just gets to the yellow warning screen, then goes black. Just bought this today on a black friday sale for 49.00
But did it for a reason. Now I would like to be able to recover it....
I was able to run adb and fastboot, so know that the drivers work, but it looks like it won't even get there now.
And it won't even go to the recovery, so I guess this phone is a real brick.
Can't seem to get the back cover off to remove the battery either.
Click to expand...
Click to collapse
download hisuite, enable oem unlocking and usb debbuginig, you gotta also get tha password or the unlocking, denn u run cmd and type:
adb devices
i hope i helped
there is easy way to get unlock bootloader pass for all huawei
just by IMEI search on google "hardreset24 unlock bootloader" there is full info how to do it
BTJustice said:
Where do you get the USB driver at because I am not seeing it at http://consumer.huawei.com/us/support/phones/ascend-xt/
Click to expand...
Click to collapse
Here is the site for USB drivers for all Huawei models:
http://huaweiadvices.com/download-huawei-usb-drivers/
Good luck....
Does the phone even have a fastboot mode?
RomLord14495 said:
Does the phone even have a fastboot mode?
Click to expand...
Click to collapse
Sure it does
Notes on booting up the phone (from power off)
Bootloader (fastboot) = power + volume down + USB hooked to pc
eRecovery = power + volume up + USB hooked to PC
TWRP = power + volume up
Click to expand...
Click to collapse
Optionally you put phone into bootloader/fastboot or recovery modes by typing from an adb prompt "reboot bootloader" or "reboot recovery"
Hi there. The website link for submitting your imei to get the unlock code doesn't work. Does anyone know how to get this code now?
dominoes20 said:
Hi there. The website link for submitting your imei to get the unlock code doesn't work. Does anyone know how to get this code now?
Click to expand...
Click to collapse
You'll have to use DC Unlocker and pay to unlock until the page returns
Since unlocking the bootloader is no longer supported, I have a suggestion but am afraid to try myself.
So, download stock version of rom (aka fastboot rom). Extract, replace recovery.img with twrp (renamed to recovery.img). Restart phone in EDL mode, flash. In theory, edl is working fastboot mode so it shouldn't matter if bootloader is unlocked, correct?
ezopantyd said:
there is easy way to get unlock bootloader pass for all huawei
just by IMEI search on google "hardreset24 unlock bootloader" there is full info how to do it
Click to expand...
Click to collapse
Imma try this out, I’m stuck in a weird situation where my sd card slot broke. When I sent it in for service, they said it was rooted and refused to fix it. I specifically did not root it so that I could send it in for warranty service. So it’s mission to try and root, unlock boot loader etc so that I can have more storage space
---------- Post added at 11:50 AM ---------- Previous post was at 11:36 AM ----------
ezopantyd said:
there is easy way to get unlock bootloader pass for all huawei
just by IMEI search on google "hardreset24 unlock bootloader" there is full info how to do it
Click to expand...
Click to collapse
Can you be a little more specific? I didn’t get that info on google
Greetings…
W̶i̶l̶l̶ ̶d̶o̶n̶a̶t̶e̶ ̶2̶0̶ ̶U̶S̶D̶ ̶t̶o̶ ̶w̶h̶o̶e̶v̶e̶r̶ ̶c̶a̶n̶ ̶f̶i̶x̶ ̶m̶y̶ ̶p̶h̶o̶n̶e̶ Fixed and contacted both Bordo_Bereli51 and Ante0.
My Huawei Mate 10 got in a bootloop after installing Xposed Framework
It was on Android Oreo 8.0 rooted and bootloader unlocked
Lock state info:
FB LockState: LOCKED
USER LockState: UNLOCKED
Leaving the device to boot normally: HUAWEI logo then reboots.
Vol up+power: eRecovery mode … doesn’t work (wiped data and cache .. tried to download firmware through wifi .. nothing works). ... then tried this method it worked while downloading the firmware .. but after verifying the firmware then installing it when it gets from 0% to 1% it fails and a red exclamation mark appears. :crying:
Vol down + power: fastboot: always get: FAILED (remote: Command not allowed) ). even though the bootloader is supposed to be unlocked. :crying:
Vol up and down: download mode .. on USB: stuck at 5% … without USB connection to computer: nothing happens (a red exclamation mark appears).
The device has an SD card slot: I tried placing the UPDATE.APP in dload folder and pressed both volume buttons but nothing appeared .. did I do something incorrectly?
Here are more info:
product-model: ALP-L29
vendorcountry: hw/meafnaf
build-number: System 8.0.0.38(0310)
fastboot getvar rescue_enter_recovery
getvar:rescue_enter_recovery FAILED (remote: FAIL:need all image flashed!)
fastboot oem oeminforead-SYSTEM_VERSION
...
(bootloader) :ALP-L29 8.0.0.128(C185)
Please help.
thanks in advance
====================
FIXED: Thanks to Bordo_Bereli51 who wrote this post and thanks for Ante0 for recommending DC Pheonix and for taking a lot of his time explaining a lot of things to me privately. contacted both as promised.
How I fixed it (credits to Bordo_Bereli51 for the guide .. I only modified it a bit and added some info from my experience):
1- I purchased a 19 euro -3 days pass for DC Pheonix.
2- Download Firmware Finder and click the "Common Base" tab, then download a FullOTA-MF firmware (all 3 files) which is approved for installation ( I copied the "changelog" link and pasted it in the 6th icon at the top "Firmware Checker" and it returned "Firmware approved for install" I' was not able to repack other non approved firmwares).
3- extract UPDATE.APP from update.zip
4- run DC Phoenix program .. tap the "Standard" button in Update mode .. select "update" and choose the UPDATE.APP you just extracted.
5- let it flash everything successfully then redo step 4 again.
6- Here's the trick before it flashes anything ... as soon as you see "utilizing backdoor" (or something like that) open Task Manager and force close DC Phoenix (it has to be BEFORE flashing anything, otherwise you might get errors like:
"error: exec '/system/bin/sh' failed: No such file or directory"
and AFTER utilizing backdoor (so you can use fastboot commands)
7-Download HWOTA8_Mate10 , place the 3 files you downloaded in step 2 in the "repack" folder, and rename "update_data_full_public.zip" to "update_data_public.zip" and "update_full_*ALP-L29*_hw_*meafnaf*.zip" to "update_all_hw.zip". Then run "repack.bat" and wait for it to finish.
8- run "ota.bat" in "ota" folder.
9- When it flashes the recovery_ramdisk and kernel plug your usb cable out and Reboot to recovery by pressing volume up + power button
10- When the phone is in recovery now ADB works (in case you need to do things manually).
11- When this process also finishes, the command center will tell you to press enter, so it boots to erecovery, which will flash the files.
12- Now your phone is unbricked after the flash.
Do not forget to do factory reset by pressing again at boot: (power + volume up) and selecting (factory reset).
After boot allow (OEM Unlock) under (developer settings) or otherwise the FRP will still be locked but the phone will work.
if someone will fix it can u tell me cause i have the same problem
---------- Post added at 06:58 AM ---------- Previous post was at 06:58 AM ----------
wait do u have twrp?
Dolev234786 said:
if someone will fix it can u tell me cause i have the same problem
---------- Post added at 06:58 AM ---------- Previous post was at 06:58 AM ----------
wait do u have twrp?
Click to expand...
Click to collapse
I have the same problem.
Dolev234786 said:
if someone will fix it can u tell me cause i have the same problem
---------- Post added at 06:58 AM ---------- Previous post was at 06:58 AM ----------
wait do u have twrp?
Click to expand...
Click to collapse
No, I don’t have TWRP.
hero3210 said:
No, I don’t have TWRP.
Click to expand...
Click to collapse
What does fastboot mode say, unlocked on both phone and frp?
ante0 said:
What does fastboot mode say, unlocked on both phone and frp?
Click to expand...
Click to collapse
yes both are unlocked
Dolev234786 said:
yes both are unlocked
Click to expand...
Click to collapse
Post input & output when you try to flash using fastboot
ante0 said:
Post input & output when you try to flash using fastboot
Click to expand...
Click to collapse
My device used to be bootloader unlocked
But I always get "FAILED (remote: Command not allowed)" for any fastboot command
I searched here and a lot of people had the same issue and they fixed it by relocking then re-unlocking the bootloader
I tried that .. relocked successfully but now I cannot unlock it again.
This is the current info from info.bat:
Lock state info:
FB LockState: LOCKED
USER LockState: RELOCKED
in fastboot mode it says:
PHONE Relocked
FRP Lock
=====
Input and output of fastboot:
fastboot flash recovery_ramdisk SYSTEM.img
target reported max download size of 471859200 bytes
sending sparse 'recovery_ramdisk' 1/7 (460797 KB)...
OKAY [ 3.650s]
writing 'recovery_ramdisk' 1/7...
FAILED (remote: Command not allowed)
finished. total time: 3.661s
Thanks for taking time to reply
hero3210 said:
My device used to be bootloader unlocked
But I always get "FAILED (remote: Command not allowed)" for any fastboot command
I searched here and a lot of people had the same issue and they fixed it by relocking then re-unlocking the bootloader
I tried that .. relocked successfully but now I cannot unlock it again.
This is the current info from info.bat:
Lock state info:
FB LockState: LOCKED
USER LockState: RELOCKED
in fastboot mode it says:
PHONE Relocked
FRP Lock
=====
Input and output of fastboot:
fastboot flash recovery_ramdisk SYSTEM.img
target reported max download size of 471859200 bytes
sending sparse 'recovery_ramdisk' 1/7 (460797 KB)...
OKAY [ 3.650s]
writing 'recovery_ramdisk' 1/7...
FAILED (remote: Command not allowed)
finished. total time: 3.661s
Thanks for taking time to reply
Click to expand...
Click to collapse
You need to enable OEM unlock in Settings-developer options. At least frp needs to say unlock else you won't be able to unlock or flash, at least not for free.
But since you can't boot you're pretty much limited to use dc unlocker/dc phoenix
ante0 said:
You need to enable OEM unlock in Settings-developer options. At least frp needs to say unlock else you won't be able to unlock or flash, at least not for free.
But since you can't boot you're pretty much limited to use dc unlocker/dc phoenix
Click to expand...
Click to collapse
Thanks for the reply
Do you recommend that I use dc unlocker or dc pheonix or FunkyHuawei?
do you recommend that I use dc unlocker or dc pheonix or FunkyHuawei?
hero3210 said:
Thanks for the reply
Do you recommend that I use dc unlocker or dc pheonix or FunkyHuawei?
Click to expand...
Click to collapse
Dc phoenix is what you'll need, Mate 10 is not supported in DC Unlocker. (Though DC Unlocker made DC Phoenix)
You'd just want it to flash stock anyway.
And it's cheaper than FunkyHuawei... FH "only" cost 1 credit to flash, but minimum to buy is 5 credits which is $41.
FH is easier though as you'd only need to setup DNS, but it's up to you
HCU/DC Phoenix pass for 3 days is €19, and then you have unlimited usage.
If you need further help you can find me at the telegram group https://t.me/HuaweiMate
as it's easier to do it live than through messages.
There is a "DC Phoenix repair tutorial" if you google it, use Method 1. Basically you just download the firmware update zip you're on now (and hw data zip) from http://pro-teammt.ru/firmware-database/ then extract update.app from it and select it in Phoenix, then extract update.app from hw data zip and select it as customization.
Alternatively you can downgrade to factory build using images from DC Phoenix (the build your phone came with) then update from there when you have a booting phone.
Thank you sooo much man. I really appreciate your help.
What version of Xposed frameworks did you install I have beta 4 working fine on my mate 10 pro.
tokoam said:
What version of Xposed frameworks did you install I have beta 4 working fine on my mate 10 pro.
Click to expand...
Click to collapse
yeah the bootloop was fixed in beta4 (original comment by dev) which wasn't officially released to the channel when I installed it, so I didn't know about it until I got the bootloop.
Anyways, I just managed to fix my issue. I'll post about it now.
ante0 said:
What does fastboot mode say, unlocked on both phone and frp?
Click to expand...
Click to collapse
what would happens if it says unlock on frp? i cant load twrp i have flashed many times but i does not take it.
I bricked my Huawei Mate 10 too
Please help.. I also bricked my Huawei Mate 10 ALP-L29C636...
I installed the EMUI 9.0 on my device using the HWOTA8_Mate10 method which was successful. The EMUI 9.0 ROM was from FirmwareFinder: ROM version ALP-L29C636E2R1P8B108-log (9.0.0.108). I didn't have any issues at all but since Huawei Mate 10's EMUI 9.0 is still in Beta, I decided to switch back to the stable EMUI 8.0.
Here's where the problem started... Since I want to downgrade, I went ahead and downloaded the 3 needed files (update.zip, update_all_hw, update_data_public) from FirmwareFinder: ROM version ALP-L29C636B143 (8.0.0.143). I fired up HWOTA8_Mate10 and started the installation process. The first step was to boot to fast boot and then plug the device, after that, the software asked me to unplug the device and press volume+ and power button but the device won't boot to recovery anymore. The device is now stuck at "Your device is booting now..." I tried rebooting the device but it won't work. Tried to go to eRevovery to wipe cache/factory reset but it will go back to "Your device is booting now..." page. I tried reinstalling the recovery.img via fastboot and tried to boot to recovery mode again but it won't work anymore. I believe my device is now soft bricked . I can still boot to fastboot, I even tried fastboot flash system system.img which was successful but the device still won't boot. Please help how to recover my device. I think I went too far and now I don't know how to fix this issue.
Carnage! said:
Please help.. I also bricked my Huawei Mate 10 ALP-L29C636...
I installed the EMUI 9.0 on my device using the HWOTA8_Mate10 method which was successful. The EMUI 9.0 ROM was from FirmwareFinder: ROM version ALP-L29C636E2R1P8B108-log (9.0.0.108). I didn't have any issues at all but since Huawei Mate 10's EMUI 9.0 is still in Beta, I decided to switch back to the stable EMUI 8.0.
Here's where the problem started... Since I want to downgrade, I went ahead and downloaded the 3 needed files (update.zip, update_all_hw, update_data_public) from FirmwareFinder: ROM version ALP-L29C636B143 (8.0.0.143). I fired up HWOTA8_Mate10 and started the installation process. The first step was to boot to fast boot and then plug the device, after that, the software asked me to unplug the device and press volume+ and power button but the device won't boot to recovery anymore. The device is now stuck at "Your device is booting now..." I tried rebooting the device but it won't work. Tried to go to eRevovery to wipe cache/factory reset but it will go back to "Your device is booting now..." page. I tried reinstalling the recovery.img via fastboot and tried to boot to recovery mode again but it won't work anymore. I believe my device is now soft bricked . I can still boot to fastboot, I even tried fastboot flash system system.img which was successful but the device still won't boot. Please help how to recover my device. I think I went too far and now I don't know how to fix this issue.
Click to expand...
Click to collapse
Spamming every thread won't help you fix your issue.
Pretoriano80 said:
Spamming every thread won't help you fix your issue.
Click to expand...
Click to collapse
I apologize. I panicked since I don't know what to do. I will continue on the thread which I received a response.