Got a Pixel 4a in yesterday and a couple screen protectors. Here are my thoughts on them, in case this is useful for somebody.
[3 Pack]OMOTON Screen Protector for Google Pixel 4a, Easy-Install/Bubble Free/Tempered Glass Screen Protector for Pixel 4a
jaxidian said:
This screen protector has no cutout for the front-facing camera. They claim it's because a cutout causes the glass to break much more in that area. There is a bit of a notch for the earpiece speaker. It does come with a snap-on mounting guide to help you easily center the TGSP while installing. While it's not "full coverage", it does cover the full usable area of the screen. There is no adhesive, it does the suction/static cling thing that most screen protectors do today. I had some issues with some air bubbles that were always there (not from dust - I assume from imperfectly flat glass) but we'll give it a couple days to see if they go away. The screen protector fits nicely with a Caseology Parallax case with just a smidgen of a gap between the case and screen protector on all sides. The clarity and feel of the screen protector is just fine. I'm going to reserve judgment on whether or not this is a good permanent screen protector, but I definitely recommend this as a "cheap and good enough for now until we discover the great ones".
Click to expand...
Click to collapse
(3 Pack) Orzero Compatible for Google Pixel 4a Tempered Glass Screen Protector with Alignment Frame, 9 Hardness HD Anti-Scratch (Lifetime Replacement)
jaxidian said:
This screen protector has a cutout for the front-facing camera. There is no notch for the earpiece speaker. It does come with a snap-on mounting guide to help you easily center the TGSP while installing. While it's not "full coverage", it does cover the full usable area of the screen. There is no adhesive, it does the suction/static cling thing that most screen protectors do today. I have not installed this screen protector since the Omotion one above surprised me with how good it was (I expected it to be trash and this to be the better one). The screen protector fits nicely with a Caseology Parallax case with just a smidgen of a gap between the case and screen protector on all sides. It seems fine not having installed it, but I can offer no opinions on it as a whole - I just wanted to share what I could.
Click to expand...
Click to collapse
If somebody gets a different screen protector or has a different opinion, post it here in this thread and PM me and I'll quote you up here in the OP.
Good to hear about the Omoton. I was pretty satisfied with the one on my OnePlus 6T. Got it perfect the first time, no lint or bubbles underneath, and it's still that way a month later. That's what I ordered for the 4a that's on the way.
Bought a "Lightning King" (L[emoji298]K) for a 3a off Amazon for cheap. You get three glass protectors which have camera cut out. I'm very satisfied with this product... And I'm picky.
If they make one for 4a get it
Nylo
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Purchased these off of Amazon and they seem okay until you try to get the edges to seal to the screen. Mine has a small gap I think because the actual screen protector is too big for the screen. So I would avoid.
https://www.amazon.com/gp/product/B08BRY8FX3/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Have the Omoton protector. Covers the usable screen, could be a bit wider, but it's better than their 3a protector, which distorted the edges of the display. No clarity issues, no installation issues. The cutout at the top of the screen for the speaker is unnecessarily wide. No hole punch. Reddit hasn't noticed a difference in selfie quality with/without a screen protector covering the camera.
My review of the Zagg Invisishield screen protector offered on the Google Play Store. Within 2 days of receiving the phone & applying the protector, I had thought I cracked my screen. Turned out to be the screen protector so Google is refunding me for that 40 bucks. Whew. Don't get tempered glass protectors. I hadn't dropped the phone or anything so the Zagg just decided to splinter and crack on its own.
jjesusfreak01 said:
Have the Omoton protector. Covers the usable screen, could be a bit wider, but it's better than their 3a protector, which distorted the edges of the display. No clarity issues, no installation issues. The cutout at the top of the screen for the speaker is unnecessarily wide. No hole punch. Reddit hasn't noticed a difference in selfie quality with/without a screen protector covering the camera.
Click to expand...
Click to collapse
I'm using the same. Works well for me too. No issues.
Nylo said:
Bought a "Lightning King" (L[emoji298]K) for a 3a off Amazon for cheap. You get three glass protectors which have camera cut out. I'm very satisfied with this product... And I'm picky.
If they make one for 4a get it
Nylo
Click to expand...
Click to collapse
They do make one and they're excellent. The installation is very easy with the supplied frame. It looks like it will work with pretty much any case.
I purchased the Mr. Shield screen protectors. I have had them for a few phones now and they always honor the lifetime warranty when I ask for replacements.
This one fits well. On the sides it is exactly as wide as the lit portion of the screen. No issue, but a tiny bit wider might have helped those who are not great with I stalls. Top and bottom are a little longer than the lit portion of the screen.
I will say this one does a very very good job fighting oils and fingerprints. I have not had to clean the screen once in 3 days.
Overall great price. They have great customer service and it fits well. If you have trouble installing screen protectors this one might be difficult as the width is exactly the same as the screen.
https://smile.amazon.com/dp/B085NNHVXL/ref=cm_sw_r_cp_apa_i_RERqFbS328P6E
ESR one sucks. Stupid halo/rainbow effect in the middle. Don't get that one. I have the Unique Me brand one coming as well to try.
---------- Post added at 09:21 PM ---------- Previous post was at 09:20 PM ----------
Uh60m Pilot said:
I purchased the Mr. Shield screen protectors. I have had them for a few phones now and they always honor the lifetime warranty when I ask for replacements.
This one fits well. On the sides it is exactly as wide as the lit portion of the screen. No issue, but a tiny bit wider might have helped those who are not great with I stalls. Top and bottom are a little longer than the lit portion of the screen.
I will say this one does a very very good job fighting oils and fingerprints. I have not had to clean the screen once in 3 days.
Overall great price. They have great customer service and it fits well. If you have trouble installing screen protectors this one might be difficult as the width is exactly the same as the screen.
https://smile.amazon.com/dp/B085NNHVXL/ref=cm_sw_r_cp_apa_i_RERqFbS328P6E
Click to expand...
Click to collapse
Any rainbow effect or adhesion issues on the edges?
Another down vote for Zagg. The corner with the cutout won't fully adhere to the screen.
I ordered ArmorShield. I had it on my last two phones and it was an excellent protector that lasted over two years. I had to order from the company because AMZ didn't have stock yet.
mrsatan said:
Any rainbow effect or adhesion issues on the edges?
Click to expand...
Click to collapse
If you install it correctly it looks perfect. When you shift the phone side to side you can see one small line for the edge of pixels.
I am almost OCD about this stuff and it has not even captured my eye once. Just my 2 cents.
I got these: https://www.amazon.com/dp/B086V7DFPC/ref=cm_sw_r_cp_apa_i_DiisFbB200TCM
Easy install, all good. No issue with Spigen Crystalclear case. Has a cut out for the camera, we will see how it holds up.
Have used Ailun & SuperShieldz, along with a couple of others in the past, this time I decided to give "Lightning King" (LK) a try. Got 3 in the box, along with the alignment frame and plenty of cleaning supplies for installation. Installed the first one yesterday; went on fine, perfectly aligned, crystal clear, no conflict with the Spigen Tough Armor case, and looked to be of high quality, similar to Ailun & SuperShieldz. Totally satisfied.
AndroidLinuxMan said:
Have used Ailun & SuperShieldz, along with a couple of others in the past, this time I decided to give "Lightning King" (LK) a try. Got 3 in the box, along with the alignment frame and plenty of cleaning supplies for installation. Installed the first one yesterday; went on fine, perfectly aligned, crystal clear, no conflict with the Spigen Tough Armor case, and looked to be of high quality, similar to Ailun & SuperShieldz. Totally satisfied.
Click to expand...
Click to collapse
Yep. First time I've ever bought them with an alignment frame included - worked very well.
I've never used a screen protector before, but now that a canister of cooking spray fell and broke my 3a XL's glass and display, I have an order for a 4a Just wondering, honestly, how well tempered screen protectors actually work. My understanding is that in theory, in my situation for example, instead of the glass/display being broken, a protector would have shattered first, more than likely saving the actual phone screen. Do these protectors help a whole lot, or not all that much in real world use if stuff falls on the phone, or you drop it and are unlucky that it should fall face-down on a hard surface? I do have an order for protectors on the way this time since it seems like it can't hurt.,
id4rox said:
I've never used a screen protector before, but now that a canister of cooking spray fell and broke my 3a XL's glass and display, I have an order for a 4a Just wondering, honestly, how well tempered screen protectors actually work. My understanding is that in theory, in my situation for example, instead of the glass/display being broken, a protector would have shattered first, more than likely saving the actual phone screen. Do these protectors help a whole lot, or not all that much in real world use if stuff falls on the phone, or you drop it and are unlucky that it should fall face-down on a hard surface? I do have an order for protectors on the way this time since it seems like it can't hurt.,
Click to expand...
Click to collapse
Over the years, I have chipped, cracked and, in one case, shattered screen protectors; but never had the phone screen damaged. In the vast majority of those cases, I'm sure there would have been damage to the phone. I also put cases on my phones, for the same reason.
AndroidLinuxMan said:
Have used Ailun & SuperShieldz, along with a couple of others in the past, this time I decided to give "Lightning King" (LK) a try. Got 3 in the box, along with the alignment frame and plenty of cleaning supplies for installation. Installed the first one yesterday; went on fine, perfectly aligned, crystal clear, no conflict with the Spigen Tough Armor case, and looked to be of high quality, similar to Ailun & SuperShieldz. Totally satisfied.
Click to expand...
Click to collapse
Can you show how the LK protector fits the display? Like the camera cutout and how far past the display does the protector go or does it end with the display? I have a LK protector on my 3a and it's the best fitting protector I've ever had. I have a 4a coming and want to confirm if the LK protectors fit correctly before I order.
Thank you ?
joedajoester said:
Can you show how the LK protector fits the display? Like the camera cutout and how far past the display does the protector go or does it end with the display? I have a LK protector on my 3a and it's the best fitting protector I've ever had. I have a 4a coming and want to confirm if the LK protectors fit correctly before I order.
Thank you
Click to expand...
Click to collapse
Maybe check out some of the reviews/pictures/videos on Amazon. It looks like there are pictures of what you're asking for I bought the LK based on what I've read here, just waiting for my 4a and case, protectors,, to come in!
Related
I'm looking for the best screen protector. Most important is functionality, so the least amount of stylus/touch sensitivity reduction.
I've tried the armorsuit military shield that uses liquid applicator and it causes too much friction and sensitivity reduction.
I'm now looking at the various generic film protectors and the 1 glass protectors linked below
intelliGLASS https://www.amazon.com/dp/B00TD9G9R2/ref=cm_sw_r_awd_WSgevb1JDHSXF
Glass protectors offer the best damage protection. I'm curious as to the performance with this shield.
Has anyone tried it?
I have, and the screen protector does not seem to affect stylus or touch functionality in any way
Sent from my SHIELD Tablet using Tapatalk
2me3 said:
I'm looking for the best screen protector. Most important is functionality, so the least amount of stylus/touch sensitivity reduction.
I've tried the armorsuit military shield that uses liquid applicator and it causes too much friction and sensitivity reduction.
I'm now looking at the various generic film protectors and the 1 glass protectors linked below
intelliGLASS https://www.amazon.com/dp/B00TD9G9R2/ref=cm_sw_r_awd_WSgevb1JDHSXF
Glass protectors offer the best damage protection. I'm curious as to the performance with this shield.
Has anyone tried it?
Click to expand...
Click to collapse
Glass is always incredible, and this one is no exception. Quality and packaging is great. I like the slight curves on the edges of the protector, makes it feel nice to the touch. I showed off my tablet to family to check it out, and until I told them it had a screen protector on, they couldn't tell what I'd added to it LOL.
I ordered the intelliARMOR intelliGLASS HD for mine. It's arrived however still waiting on my tablet to return from Nvidia (FedEx says Tuesday!) so it can try it on lol
Hoping it doesn't interfere with the case.
2me3 said:
I'm looking for the best screen protector. Most important is functionality, so the least amount of stylus/touch sensitivity reduction.
I've tried the armorsuit military shield that uses liquid applicator and it causes too much friction and sensitivity reduction.
I'm now looking at the various generic film protectors and the 1 glass protectors linked below
intelliGLASS https://www.amazon.com/dp/B00TD9G9R2/ref=cm_sw_r_awd_WSgevb1JDHSXF
Glass protectors offer the best damage protection. I'm curious as to the performance with this shield.
Has anyone tried it?
Click to expand...
Click to collapse
Chris_c81 said:
I ordered the intelliARMOR intelliGLASS HD for mine. It's arrived however still waiting on my tablet to return from Nvidia (FedEx says Tuesday!) so it can try it on lol
Hoping it doesn't interfere with the case.
Click to expand...
Click to collapse
I've been using it since I bought my Shield and its great! I can upload some pictures of it on my Shield if you want to see how it looks. There is a small cutout for the sensor on the middle upper right but other than that its an edge to edge fit (as much as it can)
Pilz said:
I've been using it since I bought my Shield and its great! I can upload some pictures of it on my Shield if you want to see how it looks. There is a small cutout for the sensor on the middle upper right but other than that its an edge to edge fit (as much as it can)
Click to expand...
Click to collapse
Do you use the official case with it mate? Does it fit well? I've had their glass products before on my HTC ONE M8 and been pleased with the quality.
Chris_c81 said:
Do you use the official case with it mate? Does it fit well? I've had their glass products before on my HTC ONE M8 and been pleased with the quality.
Click to expand...
Click to collapse
If you are referring to the magnetic folio cover then yes that's all I use with a vinyl wrap on the back to prevent scratches. There are no issues at all other than the screen protector getting dirty from the folio but the smudges wipe right off.
Pilz said:
If you are referring to the magnetic folio cover then yes that's all I use with a vinyl wrap on the back to prevent scratches. There are no issues at all other than the screen protector getting dirty from the folio but the smudges wipe right off.
Click to expand...
Click to collapse
Yeah that's the one. Excellent, thanks mate. Can't wait to get my tablet back now. Missing playing VainGlory on it! Playing on the smaller phone screen just doesn't compare lol
Chris_c81 said:
Yeah that's the one. Excellent, thanks mate. Can't wait to get my tablet back now. Missing playing VainGlory on it! Playing on the smaller phone screen just doesn't compare lol
Click to expand...
Click to collapse
My last RMA was in that recall but I had to RMA it for a different reason. Thankfully my new one (I recieved it about a month ago) is working great and doesn't have the defective battery. I usually play games on my Shield TV now but I still enjoy gaming on the tablet.
Pilz said:
My last RMA was in that recall but I had to RMA it for a different reason. Thankfully my new one (I recieved it about a month ago) is working great and doesn't have the defective battery. I usually play games on my Shield TV now but I still enjoy gaming on the tablet.
Click to expand...
Click to collapse
Coincidentally I RMA'd my Shield Tablet last Monday for a broken LCD beneath the glass. Crack occurred for no particular reason, I had never dropped it. All I recall is the night before it got quite hot. Don't think it's related to the battery issue but I'm convinced the heat of it had something to do with the crack. They accepted and my replacement was sent out yesterday due delivery Tuesday. I'm assuming it'll be a model with the unaffected battery else I'll have to RMA again...!
Chris_c81 said:
Coincidentally I RMA'd my Shield Tablet last Monday for a broken LCD beneath the glass. Crack occurred for no particular reason, I had never dropped it. All I recall is the night before it got quite hot. Don't think it's related to the battery issue but I'm convinced the heat of it had something to do with the crack. They accepted and my replacement was sent out yesterday due delivery Tuesday. I'm assuming it'll be a model with the unaffected battery else I'll have to RMA again...!
Click to expand...
Click to collapse
That's good to hear, mine was an advanced RMA so I had it in 2 days and sent the original back without any issues. My original one was almost non functional after downgrading from the original 3.0 back to 2.2.1 and no matter how many times I flashed the stock image or a different ROM it stuttered and froze. They suspected there might have been hardware damage from the OTA 3.0 somewhere in the CPU/GPU which doesn't make sense and they never gave me an answer on what was wrong. I'm still glad this one is working better, in fact I'm typing this reply on it.
Applied the IntelliGlass by IntelliArmor to my Shield today. Here's my impressions and mini-review.
The protector comes well packaged in a book style packaging. You get everything you'll need inside to make applying the protector a breeze. Includes:
- protector
- dust removal sheet
- alcohol wipe
- lint free cloth
- smudger
Simply cleaned the screen with the wipe, applied the dust removal sheet several times and then began peeling off the backing and lining up the glass protector. My first hit was slightly off, enough to irritate me anyway! So had to gently prise it off and re-seat it. Second hit was perfect. The bubbles smoothed out easily with my thumb pressure.
I've had IntelliArmor products before and as with all glass protection I've owned in the past, they are the ultimate screen protection and offer so much more then plastic ones. The best advantage for me though is that your finger feels like its on the actual screen as plastic protectors can give differing feeling under the finger.
I've been unlucky enough to drop my phone before onto a hard surface and if it were not protected by a glass screen protector, I'm confident the screen would have shattered. Instead the screen was fine below the shattered and chipped glass protector. So I've had first hand experience that glass protectors do the job. I've no reason to believe any different of this product, without me chucking my Shield on the floor - which I won't do for a review!
The glass is not too thick and plays nicely with the Official Nvidia case which is an added bonus as not all glass protectors play well with flip style cases. Fortunately this one does.
My only gripe at the moment is when swipe typing. It currently seems a bit hindered by the glass protector. However, I need more time with it as I'm not 100% convinced it has all to do with the protector.
If you're in the market for a Shield screen protector, then I highly recommend the IntelliGlass. Worth the extra £'s in my humble opinion.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Chris_c81 said:
Applied the IntelliGlass by IntelliArmor to my Shield today. Here's my impressions and mini-review.
The protector comes well packaged in a book style packaging. You get everything you'll need inside to make applying the protector a breeze. Includes:
- protector
- dust removal sheet
- alcohol wipe
- lint free cloth
- smudger
Simply cleaned the screen with the wipe, applied the dust removal sheet several times and then began peeling off the backing and lining up the glass protector. My first hit was slightly off, enough to irritate me anyway! So had to gently prise it off and re-seat it. Second hit was perfect. The bubbles smoothed out easily with my thumb pressure.
I've had IntelliArmor products before and as with all glass protection I've owned in the past, they are the ultimate screen protection and offer so much more then plastic ones. The best advantage for me though is that your finger feels like its on the actual screen as plastic protectors can give differing feeling under the finger.
I've been unlucky enough to drop my phone before onto a hard surface and if it were not protected by a glass screen protector, I'm confident the screen would have shattered. Instead the screen was fine below the shattered and chipped glass protector. So I've had first hand experience that glass protectors do the job. I've no reason to believe any different of this product, without me chucking my Shield on the floor - which I won't do for a review!
The glass is not too thick and plays nicely with the Official Nvidia case which is an added bonus as not all glass protectors play well with flip style cases. Fortunately this one does.
My only gripe at the moment is when swipe typing. It currently seems a bit hindered by the glass protector. However, I need more time with it as I'm not 100% convinced it has all to do with the protector.
If you're in the market for a Shield screen protector, then I highly recommend the IntelliGlass. Worth the extra £'s in my humble opinion.
]
Click to expand...
Click to collapse
I'm glad to see its working well for you. I wouldn't use my tablet without one know how clumsy I can be.
Chris_c81 said:
Applied the IntelliGlass by IntelliArmor to my Shield today. Here's my impressions and mini-review.
The protector comes well packaged in a book style packaging. You get everything you'll need inside to make applying the protector a breeze. Includes:
- protector
- dust removal sheet
- alcohol wipe
- lint free cloth
- smudger
Simply cleaned the screen with the wipe, applied the dust removal sheet several times and then began peeling off the backing and lining up the glass protector. My first hit was slightly off, enough to irritate me anyway! So had to gently prise it off and re-seat it. Second hit was perfect. The bubbles smoothed out easily with my thumb pressure.
I've had IntelliArmor products before and as with all glass protection I've owned in the past, they are the ultimate screen protection and offer so much more then plastic ones. The best advantage for me though is that your finger feels like its on the actual screen as plastic protectors can give differing feeling under the finger.
I've been unlucky enough to drop my phone before onto a hard surface and if it were not protected by a glass screen protector, I'm confident the screen would have shattered. Instead the screen was fine below the shattered and chipped glass protector. So I've had first hand experience that glass protectors do the job. I've no reason to believe any different of this product, without me chucking my Shield on the floor - which I won't do for a review!
The glass is not too thick and plays nicely with the Official Nvidia case which is an added bonus as not all glass protectors play well with flip style cases. Fortunately this one does.
My only gripe at the moment is when swipe typing. It currently seems a bit hindered by the glass protector. However, I need more time with it as I'm not 100% convinced it has all to do with the protector.
If you're in the market for a Shield screen protector, then I highly recommend the IntelliGlass. Worth the extra £'s in my humble opinion.
View attachment 3427492
View attachment 3427493
View attachment 3427494
Click to expand...
Click to collapse
Q: dirt under the neckline falls?
Brigadir120370 said:
Q: dirt under the neckline falls?
Click to expand...
Click to collapse
I have no idea what you just said.
Chris_c81 said:
I have no idea what you just said.
Click to expand...
Click to collapse
Sorry for the bad translation! I ask you: dust gets under the protection?:смущенный:
Brigadir120370 said:
Sorry for the bad translation! I ask you: dust gets under the protection?:смущенный:
Click to expand...
Click to collapse
Ah! Ok no problem.
No I've not experienced any dust gathering underneath the edges. It's a pretty good seal once it's on.
Chris_c81 said:
Ah! Ok no problem.
No I've not experienced any dust gathering underneath the edges. It's a pretty good seal once it's on.
Click to expand...
Click to collapse
Thank you so much!
So I'm a true believer in tempered glass screen protector because it saved me in thousands. I bought some cheap one even before the phone came out to use until the proper one comes out. This one is just square to cover the viewable screen. I bought two of them and both of them doesn't adhere at the bottom corners on two different phones. I went online to do some digging and found that most if not not all have the same issue and all sellers showing full screen cover does a bait and switch and send out the very exact same square ones.
I'm now beginning to wonder... Is this because all sellers have same batch of cheap stuff that doesn't fit or is it because G5 screen isn't perfectly flat? (never mind the curve on top) it seems the glass used on G5 is more flexible because when you press hard on it you can see the LCD distortion in some spots. In normal use it should not matter and I guess it was necessary to make the top curvature but it can also mean that when the the glass and LCD assembly can become "curvy".
Has anyone applied tempered glass protector yet? How did your application experience go? And if you had a successful one, please share the info of the product you used. NO LINKS.
Please, this is not an ad space. Only the real users with real input is welcome.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my LG-H820 using XDA-Developers mobile app
The glass screen is indeed squishy. This is expected. The G4 was curved. I expect squishy glass is less likely to shatter.
pigowar said:
So I'm a true believer in tempered glass screen protector because it saved me in thousands. I bought some cheap one even before the phone came out to use until the proper one comes out. This one is just square to cover the viewable screen. I bought two of them and both of them doesn't adhere at the bottom corners on two different phones. I went online to do some digging and found that most if not not all have the same issue and all sellers showing full screen cover does a bait and switch and send out the very exact same square ones.
I'm now beginning to wonder... Is this because all sellers have same batch of cheap stuff that doesn't fit or is it because G5 screen isn't perfectly flat? (never mind the curve on top) it seems the glass used on G5 is more flexible because when you press hard on it you can see the LCD distortion in some spots. In normal use it should not matter and I guess it was necessary to make the top curvature but it can also mean that when the the glass and LCD assembly can become "curvy".
Has anyone applied tempered glass protector yet? How did your application experience go? And if you had a successful one, please share the info of the product you used. NO LINKS.
Please, this is not an ad space. Only the real users with real input is welcome.
Click to expand...
Click to collapse
Have the same Problem with my g5
I had no problem with the bottom corners, bot the top was just on your photo.
RealLordK1 said:
I had no problem with the bottom corners, bot the top was just on your photo.
Click to expand...
Click to collapse
That's the concern I have. I really hope that the cheap, mocked up protector is the issue and not the screen. Top is fine since we know there's curve. We need more owners to provide their experience but may be there aren't that many who purchased the early version of the protectors knowing they would not fit well?
Sent from my LG-H820 using XDA-Developers mobile app
I got my glass screen protector at at&t and installed there, i thought that i was rid of the issue that the protector would not come up at the edges but a week and a half it came up and now i removed the protector and clean it and cleaned the screen and used some clean water to put it on and then i had no issue about the protector coming off at the edges
There's another thread: Here where the same issue is experienced.
I wonder if this is with all G5s or is this just the Titan color that has this issue as some user mention they have Silver devices without the issue.
Tried 3 different suppliers for tempered glass protector and they all did this. I think it's the screen not the protectors.
I installed a cheap square screen protector and am waiting for a "real" one to show up. Currently on order, but taking longer than they originally said. With the one I have on now, I found that you have to install is slightly above the bottom of the screen to be sure it doesn't interfere with the lower, removable pieces of the phone. When I put it on just slightly higher than I wanted to it fit OK. It took me a bunch of tries and the lower right corner has a small bubble in it, but I attributed that to my several installation attempts. The three other corners are fine.
Just got a Yootech Premium glass protector on Amazon last week. It's curved for the tip, so it's a film glasses protector. No issues whatsoever. Fit/alignment is perfect. They even painted the to pay black, so there's no light bleed or distortion there. I'm really happy with it.
I mean, it's a very simple thing to do accidentally. I feel like it's always a 50/50 shot when I try to put down a screen protector bubble-free.
I haven't tried a protector on the G5, but I did have one on the very curved G4 with no issues.
porsche911996 said:
Just got a Yootech Premium glass protector on Amazon last week. It's curved for the tip, so it's a film glasses protector. No issues whatsoever. Fit/alignment is perfect. They even painted the to pay black, so there's no light bleed or distortion there. I'm really happy with it.
Click to expand...
Click to collapse
Same product same results here. I waited for yootech to replace the cheap glass protector I bought at launch. I had great results on the G4 with this brand.
+1 on the Yootech. I got one and it is great. At first it looked like there was a light film in one spot between the protector and screen, but it went away in a couple hours.
http://imageshack.com/a/img924/3333/mnQNMj.jpg
Same problem ..I used Ringke screen protector
Hello everyone,
It's my first purchase of an LG device as I've always been HTC. The G5 is an amazing phone, hats off to LG for doing a great job. However, it's the worst phone when it comes to fitting a screen protector. I've purchased 5 so far. First 3 turned out to be a more bespoke cut glass at the top section to fit around the camera and underneath the speaker (all happened to be same brand from 3 different sellers, but they all had the same issue. Top section wouldn't adhere and bottom right corner too.
Bought two square protectors that just fit the visible screen and that's slightly better but small areas won't adhere, again top bottom right being the main culprit. Luckily I've been able to get refunded for the poorly fitting protectors but I'm getting fed up of having to change them every few days. I've never had such issue with fitting a protector as I normally get it spot on first time.
Anyone know where I can get a proper one, cut correctly and adhere to the LG's fussy screen?
But do any of them fit with the Spigen Style Armor slide on case?? That is the burning question.
I have a gold G5 and tried 3 tempered glasses in the mall but none fitted my phone. The corners below and above has bubbles lifting the tempered glass. It is now my problem where to find a good protector.
Vida_RPh said:
I have a gold G5 and tried 3 tempered glasses in the mall but none fitted my phone. The corners below and above has bubbles lifting the tempered glass. It is now my problem where to find a good protector.
Click to expand...
Click to collapse
I've bought this one :
https://www.amazon.com/Protector-An...losion-proof-Pressure-resistant/dp/B00WSC6IC2
It fits the screen perfectly and there is no grid in it, like others.....
Gesendet von meinem LG-H850 mit Tapatalk
---------- Post added at 07:07 AM ---------- Previous post was at 06:54 AM ----------
Sorry, i've took the wrong link.... This is the right one:
https://www.amazon.de/Schutzfolie-V...qid=1473397546&sr=8-1&keywords=sundatom+lg+g5
Gesendet von meinem LG-H850 mit Tapatalk
Hi, thanks for the help! But i cannot sign up on this amazon page because it's in german not all are being translated into english
Screen is curved
Just wanted to update you there is not a screen protector that is glass which fits the LG G5 because the screen is curved slightly in the bottom corners. This is an issue which the accessory manufacturers are aware but apparently have no intentions of resolving . So just to be perfectly clear you will not ever find a screen protector that does not bubble on the bottom right and left hand corner unless it is a plastic screen protector.
EDIT: Now that 5 months have gone by and some top contenders have truly emerged, I've updated the OP with the list of the protectors that seem to be the favorites in this thread and in others.
The purpose of this thread is to discuss screen protector options for the Pixel phone. This is where you can post thoughts and pictures of screen protectors you've purchased/used and to provide reviews and suggestions for others looking for tempered glass, plastic and wet apply screen protectors.
IntelliARMOR IntelliGLASS PRO
https://www.intelliarmor.com/shop-by-device/pixel/intelliglass-pro-pixel-black-screen-protector.html
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Pros:
- Full adhesive across the entire protector
- Full coverage
- Comes in black or white
Cons:
- Adhesive in center of screen is going to show dust particles more prominently.
- Edges may not adhere properly in some areas. (Blow dryer and pressure applied in the area for 1-2 minutes usually solves this)
Orzly 2.5D Pro-Fit Tempered Glass Screen Protector
https://www.amazon.com/Google-Prote...898800&sr=1-3&keywords=intelliglass+pro+pixel
Pros:
- Full coverage
- Comes in black or white
- Easy to apply perfectly
Cons:
- No adhesive in center of the screen which creates space between screen and protector
- Can give an almost mirror like reflection from certain angles in highly lit areas
- "Dot matrix" over the screen, making reading text difficult in direct sunlight
- Can make blacks on the screen look very washed out and gray
Spigen GLAS.t R Slim Tempered Glass Protector
https://www.amazon.com/dp/B01N8S5R93?th=1
Pros:
- Full coverage
- Comes in black or white
- Easy to apply perfectly
- No dot matrix in center of screen like Orzly
Cons:
- Can make blacks on the screen look slightly washed out (but not nearly as bad as the Orzly)
...
There are other options but these 3 seem to be the most favored among Pixel users.
I ordered the tempered glass from Verizon's website. With my discount it was like $16 and they usually work pretty well.
I got the Spigen Google Pixel Screen Protector Tempered Glass, I really like it.
Got this one: Spigen Google Pixel Screen Protector Tempered Glass / Full Coverage / 9H Hardness / Case Friendly for Google Pixel - Black
rumbikrobo said:
So many screen protectors, so little quality
Click to expand...
Click to collapse
Pleson and Orzly typically make some very solid TG protectors. However, I must admit that I'm pessimistic about the fit due to the curved edge of the screen. But at just $8 I'm willing to give it a try. Fingers crossed.
I have always been a fan of Invisible shields by Zagg. they haven't officially announced for Pixel yet though.
jed.padilla said:
I have always been a fan of Invisible shields by Zagg. they haven't officially announced for Pixel yet though.
Click to expand...
Click to collapse
BOOM!
https://www.verizonwireless.com/accessories/zagg-invisibleshield-glass-screen-protector-pixel/
I will never understand the desire to put this horrible ugly **** on your expensive phone, even worse than a case.
mdmogren said:
I will never understand the desire to put this horrible ugly **** on your expensive phone, even worse than a case.
Click to expand...
Click to collapse
A perfectly installed tempered glass protector looks and feels like it isn't even there. However, with the curved edge of the Pixel screen, I am doubtful that I will be able to accomplish a perfect install. Admittedly, after going through a few protectors with my OnePlus 3, I ended up saying "screw it" and went bare with the screen and felt liberated. :laugh:
The screen looks/feels so great without a protector that it's worth getting some micro-scratches. The main reason I try to use a screen protector is for resale value purposes. But this time around I really am hopping to keep the Pixel for the full 24 months instead of making an incremental upgrade after 12 months. By then the phone will be worth like $150 anyway. So this time around, if I can manage a perfect install with the Pleson TG protector, I'll keep it on. If it doesn't work I'm going to throw it in the trash and just enjoy the screen bare.
I purchased Google Protect anyway so if something happens to the screen I pay them $79 and get a brand new phone the next day. With protection like that it's actually gotten silly to drop upwards of $50 trying all sorts of screen protectors.
jhonwright56 said:
Try this anti bubble "skinomi" screen protector available at amazon http://amzn.to/2djc8aJ
Click to expand...
Click to collapse
I've used that screen protector on my OnePlus 3 and can't stand it. It has a rubbery feel to it and makes the screen look grainy. For me it's tempered glass or nothing.
I got the Pleson coming right now. I usually use the Skinomi glass protectors but they told me they were not ready as of yet. Pleson makes amazing cases wo i will try their screen protectors out. if they crack i will get skinomi later
I have a Pleson on my 6P and it's great.
I'm curious though, the first batch of 6P protectors covered the proximity sensor and people had issues. I'm assuming that thing under the top speaker (on the Pixel) is the proximity sensor and it appears to be covered. Maybe I'll wait for some reviews.
Sent from my Nexus 6P using Tapatalk
daewond3r said:
I have a Pleson on my 6P and it's great.
I'm curious though, the first batch of 6P protectors covered the proximity sensor and people had issues. I'm assuming that thing under the top speaker (on the Pixel) is the proximity sensor and it appears to be covered. Maybe I'll wait for some reviews.
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
They are cheap enough that I jumped in. 8 bucks for 2 of them... Why not
Sent from my Nexus 6P using Tapatalk
jerflash said:
They are cheap enough that I jumped in. 8 bucks for 2 of them... Why not
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
It's def a good deal. Not hating on anyone who's taking a chance on the first batch and I hope there's no issues. I'm just gonna wait to find out.
sn0warmy said:
Pleson and Orzly typically make some very solid TG protectors. However, I must admit that I'm pessimistic about the fit due to the curved edge of the screen. But at just $8 I'm willing to give it a try. Fingers crossed.
Click to expand...
Click to collapse
You can definitely go well with orzly, often a solid choice
lordred12345 said:
You can definitely go well with orzly, often a solid choice
Click to expand...
Click to collapse
I just hope the curved edge doesn't force the TG manufacturers to do what they did with the OnePlus 3, which was leave the adhesive on the sides and keep the middle of the protector just hovering over the screen because it created that obnoxious rainbowing in the middle of the screen and allowed dust to get in betweent he protector and the screen. .
bought the pleson TG 2 pack. I hope armor shield jumps into the game, love their stiff.
sn0warmy said:
I purchased Google Protect anyway so if something happens to the screen I pay them $79 and get a brand new phone the next day.
Click to expand...
Click to collapse
I have used Google Protect on my 5X and I assure you that your replacement will NOT be new(could be, but won't be). Change "brand new" to "refurbished" and you got it right. I tried three replacements for my 5X, all were refurbished. All had loose back covers and one had a pink screen. I ended up replacing the back cover myself with an aftermarket replacement to address the looseness.
shelleyldiaz said:
You can also go with iLLumiShield screen protector for Google Pixel.
Click to expand...
Click to collapse
^ Thanks for that link! It displays some good options for people to consider. I'm going to add this to the OP.
sn0warmy said:
I just hope the curved edge doesn't force the TG manufacturers to do what they did with the OnePlus 3, which was leave the adhesive on the sides and keep the middle of the protector just hovering over the screen because it created that obnoxious rainbowing in the middle of the screen and allowed dust to get in betweent he protector and the screen. .
Click to expand...
Click to collapse
Im confident that orzly will be okay as they did fix most of the issues with their second edition. It's what I use now
lordred12345 said:
Im confident that orzly will be okay as they did fix most of the issues with their second edition. It's what I use now
Click to expand...
Click to collapse
Yeah, I remember you and I discussing the Orzly protector for the OnePlus 3. My rev 2 was pretty solid and offered great protection with a clean look. But over a few weeks it started to let dust get in, which got annoying. The plus side to that protector is you can peal it off, clean the screen and re-apply.
However, a couple of weeks ago I decided to go with no protector on the OnePlus 3 and it just feels/looks too great to go back. Since ordering the Pixel I've been much less gentle with the OnePlus 3, as well. The screen has now been exposed to plenty of dirt/grime from using it while working on the car and even sand from our camping trip this last weekend. Yet, every time I clean it and inspect the screen under florescent lighting I can't find a single visible scratch.
And supposedly the OnePlus 3 screen is less scratch resistant than other current flagships. If that truly is the case, then I'm seriously thinking the screen protector days might be behind me. Unless I can manage a perfect install with the Pleson one I ordered, that is.
sn0warmy said:
Yeah, I remember you and I discussing the Orzly protector for the OnePlus 3. My rev 2 was pretty solid and offered great protection with a clean look. But over a few weeks it started to let dust get in, which got annoying. The plus side to that protector is you can peal it off, clean the screen and re-apply.
However, a couple of weeks ago I decided to go with no protector on the OnePlus 3 and it just feels/looks too great to go back. Since ordering the Pixel I've been much less gentle with the OnePlus 3, as well. The screen has now been exposed to plenty of dirt/grime from using it while working on the car and even sand from our camping trip this last weekend. Yet, every time I clean it and inspect the screen under florescent lighting I can't find a single visible scratch.
And supposedly the OnePlus 3 screen is less scratch resistant than other current flagships. If that truly is the case, then I'm seriously
thinking the screen protector days might be behind me. Unless I can manage a perfect install with the Pleson one I ordered, that is.
Click to expand...
Click to collapse
Ah yeah I remember your profile picture somewhat. I don't get that much dust buildup but mainly due to my case probably hiding it well!
Ideally we would all like no case or screen protector on our phones but life isn't like that ????
My OPO got quite scratched up unfortunately before I had a screen protector so I always need one now!
The title pretty much covers it. I see many questions on this, but no definitive answers. I tried the official one but returned it since it would cover the edges of the screen. Bought one off of Amazon that said it didn't do that, but it did as well.
So simply, I'm looking for one that won't cover the screen is good quality. Simple enough, no?
I bought this case by Nillkin for my phone and it came with a free screen protector film (not a glass protector) and I find it pretty decent. I didn't find any issues with fingerprints on it.
You can find it here: https://www.amazon.com/OnePlus-Nill...=1504853058&sr=8-3&keywords=oneplus+5+nillkin
The Nillkin TGSP is probably the most compatible at the moment but it does have the larger gap around the edges, I've still got mine applied, hoping for more luck with the Rhinoshield case and a full face protector as the case is supposed to be much more compatible with them, my advice would be to go for the Nillkin until we all find the perfect replacement.
http://www.dx.com/p/naxtop-tempered...for-oneplus-5-transparent-470989#.WbOz7iNnp74
Anyone tried this one?
Transparent or with black borders?
dasti555 said:
http://www.dx.com/p/naxtop-tempered...for-oneplus-5-transparent-470989#.WbOz7iNnp74
Anyone tried this one?
Transparent or with black borders?
Click to expand...
Click to collapse
Thanks. Looks interesting particularly the all transparent version, curved edges and its cheap enough to experiment. There is no indication on where the adhesion is and no specific mention of a Oleophoic coating but describes an anti-fingerprint coating. I currently have the under screen dust issue with my Orzly tgsp but I love the feel of that screen so am looking for a alternative protector with similar finger feel.
I'm suspecting that my bumper case is causing the Orzly's issue as the dust only comes from the volume rocker area and likely due to the case pushing the Orzly's edge when pressed. Maybe this alternate protector with the curved edges would not have the same issue, while the all transparent version would likely have no issues cutting off the screen view unless the curved edge causes some undesirable optical effect.
If you get one please post your observations.
3DSammy said:
Thanks. Looks interesting particularly the all transparent version, curved edges and its cheap enough to experiment. There is no indication on where the adhesion is and no specific mention of a Oleophoic coating but describes an anti-fingerprint coating. I currently have the under screen dust issue with my Orzly tgsp but I love the feel of that screen so am looking for a alternative protector with similar finger feel.
I'm suspecting that my bumper case is causing the Orzly's issue as the dust only comes from the volume rocker area and likely due to the case pushing the Orzly's edge when pressed. Maybe this alternate protector with the curved edges would not have the same issue, while the all transparent version would likely have no issues cutting off the screen view unless the curved edge causes some undesirable optical effect.
If you get one please post your observations.
Click to expand...
Click to collapse
Well I post it here because I was looking if somebody already bought it. I have orzly with I'm happy however it have rainbow effect in the middle and sometimes it's quiete visible. My friend told me that he bought that one from link I sent (with black borders) and he is told me he don't have rainbow effect or cutted screen.. so i don't know
Like you I'm more interested in the transparent one as I don't know why there is even a black version on any of them.
On my Orzly I've seen the rainbow effect but only when the screen is at an unusual angle while wiping the surface clean but never when using the phone normally. It's only the dust that is driving me crazy. I'm even considering going with just my bumper case and no protector but I'll wait a while before going that route.
This one looks interesting (not glass though), quite clever application method, reminds me of the default screen protector that comes with the phone that a lot of people seem to like
Ringke Invisible Defender Screen Protector
https://www.amazon.com/Protector-Invisible-Guaranteed-Compatible-Clearness/dp/B074137YDH/
Just read the Amazon reviews and they're not that positive.
I still have to receive my oneplus 5. Would you guys recommend keeping the pre-applied film with the orzly bumper over any screenprotector that's on the market now?
ned4spd8874 said:
The title pretty much covers it. I see many questions on this, but no definitive answers. I tried the official one but returned it since it would cover the edges of the screen. Bought one off of Amazon that said it didn't do that, but it did as well.
So simply, I'm looking for one that won't cover the screen is good quality. Simple enough, no?
Click to expand...
Click to collapse
i am in the same boat as you.
found this -
imak Oneplus 5 Transparent Clear Full Cover Edges 0.15mm TPU LCD Screen Protector for Oneplus 5 back Anti-shock Protective Film
http://s.aliexpress.com/BBBjERbi
(from AliExpress Android)
i just want clear protective glass that covers the whole screen. anything similar to whitestone dome protective glass (for s8) would be great.
I bought the one from Nillkin until a better one came along. However it was pure garbage. It didn't fit the whole screen and the top notch was way off center. But the main reason I threw it in the trash was there was the entire right side would not stick to my phone. There was a good 1/8" section all along the right edge that was not sticking and just looked like crap.
Finally the almost perfect tgsp.....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Almost perfect is because its not fully adhesive. Only perimeter adhesive.
so dust will appear along the sides and rainbow will appear sooner or later.
spawn549 said:
Finally the almost perfect tgsp.....
Almost perfect is because its not fully adhesive. Only perimeter adhesive.
so dust will appear along the sides and rainbow will appear sooner or later.
Click to expand...
Click to collapse
Which one is it
i dont recommend it. after few hours of usage tiny dust appearing from speaker and sensor holes going right inside the tgsp. the coating is bad. attracts fingerprint n dust. screen will smudge all over.
srt99 said:
i am in the same boat as you.
found this -
imak Oneplus 5 Transparent Clear Full Cover Edges 0.15mm TPU LCD Screen Protector for Oneplus 5 back Anti-shock Protective Film
http://s.aliexpress.com/BBBjERbi
(from AliExpress Android)
i just want clear protective glass that covers the whole screen. anything similar to whitestone dome protective glass (for s8) would be great.
Click to expand...
Click to collapse
I just picked up two packs for fun - will report back.
spawn549 said:
i dont recommend it. after few hours of usage tiny dust appearing from speaker and sensor holes going right inside the tgsp. the coating is bad. attracts fingerprint n dust. screen will smudge all over.
Click to expand...
Click to collapse
Got it, but wich brand produce this one? Just to look around
No brand packaging on it...i would stay away from non full adhesive due to it attracts dust and rainbow effect. I would rather use a full adhesive tgsp eventhough it will block few mm from the sides
This is the best I found for now. Not full covered but minimal bars on the side and almost no rainbow effect. After 2 weeks no dust at all.
https://fr.aliexpress.com/item/Scre...lus-3-3T-Three-1-3-1-3T-Full/32795224827.html
bibi98 said:
This is the best I found for now. Not full covered but minimal bars on the side and almost no rainbow effect. After 2 weeks no dust at all.
https://fr.aliexpress.com/item/Scre...lus-3-3T-Three-1-3-1-3T-Full/32795224827.html
Click to expand...
Click to collapse
Do you also use a case with this protector? If you do please indicate which one as even an all adhesive tgsp can be lifted by many of the cases being sold.
Disgustip8ed said:
I just picked up two packs for fun - will report back.
Click to expand...
Click to collapse
Anything new about those glass screen protectors?
I think it would be easier for us Moto X4 users to have a unified thread on available cases and screen protectors.
I recently bought the Moto X4 and my case and screen protector were just delivered.
I will post pics once I installed the plastic screen protector.
I'm still waiting for my iMAK Hydrogel Film for the front/back.
Will update you soon.
If you have anything, please post your pics as well.
Thank you!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I got the same case, except in red. It fits very well, and is quite nice! It fits very well. I was afraid it'd be too rubbery but it holds its shape well, while still being flexible enough if I need to remove it.
As usual, it blocks some headphone jacks if they have a wide base, but that's expected.
Mine was $8 on Amazon. https://www.amazon.com/gp/product/B0753CD8R7/
Yes it does fit well but too bulky for my liking. I bought mine for USD5 ?.
Anyway, I'll probably get another type of case. Here's the link on how it looks like
http://www.lazada.com.my/imak-shock...html?spm=a2o4k.search.0.0.226b6e31cAW5cj&ff=1
I'm still undecided which of the 3 to get. I want the transparent but will definitely turn yellow after sometime.
ijuanp03 said:
Yes it does fit well but too bulky for my liking. I bought mine for USD5 .
Anyway, I'll probably get another type of case. Here's the link on how it looks like
http://www.lazada.com.my/imak-shock...html?spm=a2o4k.search.0.0.226b6e31cAW5cj&ff=1
I'm still undecided which of the 3 to get. I want the transparent but will definitely turn yellow after sometime.
Click to expand...
Click to collapse
I went for the smooth case, skin type feel. Hope its not slippery and gives good grip!
i ordered these 3 things on ALIEXPRESS for supercheap prices,
waiting for them to arrive... (they usually are quite fast in deliveries with china registered airmail)
2 back covers, and 5 camera protectors (for the back camera they were so cheap i ordered 5 immediately)
https://imgur.com/a/E3R0O (click link to watch all 3 pictures)
i hope one of these backcovers will at least feel like it offers good protection for dropping on the corners.
good camera protection on the back (=creating much distance between the backcover and the camera so there is a few mm's in between,
so the camera no longer touches a surface when we lay the phone on the back)
i already have a just in case glass screenprotector, which offers smooth touch...
but it has some air beneath on both sides of the screen (i dont really care some much cause it's hardly visible when the screen is turned on).
It doesn't protect the front camera sadly enough, the touch responsitivity feels great though.
so despite all its flaws i still give a 7/10.
I added some oldschool screenprotector foil that I cut with scissors on the front camera that is not covered by the just in case screenglass.
Edit: This stuff has arrived now! I like the Imak case. It's anti skid & offers good camera protection. The other case (perfect brush texture with so called "anti slip" looks better but feels bad to hold in hand. It does not offer camera protection and is not anti slip at all!
I ordered the same brand but mine is the matte black sandy feel.
I also order the iMak hydrogel film (front and back) since I really hate normal screen protector and tempered glass.
Film protectors (a la clearcoat/zagg/ishield) are not visible and will cover most of the screen including the edges.
https://www.aliexpress.com/item/2pc...-c62b-43f8-8513-c4ff815bdfb1&rmStoreLevelAB=5
I don't have the camera lens protector though. :/ I'm considering that since Moto likes putting a coating on their camera lenses (which scratches in time) though you can remove them completely by rubbing gently with toothpaste/baking soda.
This happened to my old Moto Z.
Btw, the case I used has a good camera lens protection. It is actually raised a little bit so you can put your phone on a flat surface without worrying.
why do you hate glass, and whats so good about gel?
good glass has great touch responsitivity,
will feel just as slippery as normal glass (are there really people that like nongreasy unslippery touchscreen?),
and protects against breaking.
my current case raises the camera as well but not enough. the only ones that raise it significantly are probably those bulky book cases.
i'll probably have to raise it myself by using superglue and putting some pieces of rubber on the inside of the screenprotector.
Since most phones these days (including Moto) are using 2.5D glass, the edges are curved and tempered glass can't cover the edges. In my past Moto phones (or just any other phones), tempered glass manufacturers will either
- make a tempered glass with maximum coverage (with obvious halo effect/ tempered glass not sticking to the edges)
or
- tempered glass won't cover the edges and can't even cover the whole display (assuming the side bezels are slim).
The film will protect the whole display and looks invisible as if there is no protection whatsoever.
I'm not too worried about breakage coz I am using a case.
Update: I received the iMak hydrogel films for the front and back. I haven't installed them yet but I'm now disappointed. The films will cover more than the glass front and back!
I'll update again once I installed it on my phone.
Anyway, this is better than the plastic screen protector I'm using now.
pietpietersen: Just wondering where you purchased the screen protector that you already had?
And if anyone can provide links to tempered glass screen protectors that have hit their phones well, I would appreciate it. I keep reading reviews on Amazon saying that some of them dont fit right.
Double post! Sorry!
marxela said:
pietpietersen: Just wondering where you purchased the screen protector that you already had?
And if anyone can provide links to tempered glass screen protectors that have hit their phones well, I would appreciate it. I keep reading reviews on Amazon saying that some of them dont fit right.
Click to expand...
Click to collapse
I got the TGSP, pictured below, for the wife's X4.
It does cover the entire screen, side to side and is really hard to get it centered, side to side, because it is virtually the same width as the display.
It's cut really close to the button, camera and sensors, which also makes it difficult to get good placement.
It had the best reviews, on amazon, by far.
I really hate curved edge phones!
Triple post! Wth?
So sorry! I don't know what happened!
marxela: i got mine at smartphoneshop.be (or. nl) so its not gonna be cheap to buy or have it shipped outside of belgium/netherlands.
pizza Pablo's looks easier to place than mine, cause mine had only a tiny microphone cutout. anyway, im happy mine feels smooth to touch/swype on.
Update: Do NOT buy the iMAK hydrogel film for Moto X4. It's useless. The front and back films do NOT fit the phone itself. It's like the cutout is for an enlarge version of Moto X4!
So I have no choice but to go naked on my front screen.
ijuanp03 said:
Since most phones these days (including Moto) are using 2.5D glass, the edges are curved and tempered glass can't cover the edges. In my past Moto phones (or just any other phones), tempered glass manufacturers will either
- make a tempered glass with maximum coverage (with obvious halo effect/ tempered glass not sticking to the edges)
or
- tempered glass won't cover the edges and can't even cover the whole display (assuming the side bezels are slim).
The film will protect the whole display and looks invisible as if there is no protection whatsoever.
I'm not too worried about breakage coz I am using a case.
Update: I received the iMak hydrogel films for the front and back. I haven't installed them yet but I'm now disappointed. The films will cover more than the glass front and back!
I'll update again once I installed it on my phone.
Anyway, this is better than the plastic screen protector I'm using now.
Click to expand...
Click to collapse
Have you applied the imak hydrogel film? How does it fit? I am planning to order the same.
Edit: Got the answer. I won't order it, thanks.
I did successfully install the hydrogel film. Even if it does fit, the quality is really poor. It's like a cheap version of IQ shield or Clear Coat. There are a lot of creases and very fingerprint magnet.
I went to mobile outfitters and have my front screen installed with matte film. Problem solved.
The protector from the gadgetshieldz covers the lens, screen and body of the moto x4. I have previously used their screen protector on my moto g4. But now for my x4, I got the skins.
https://www.gadgetshieldz.com/motorola-moto-x4-screen-protectors-cases-covers.html
azriel22 said:
The protector from the gadgetshieldz covers the lens, screen and body of the moto x4. I have previously used their screen protector on my moto g4. But now for my x4, I got the skins.
https://www.gadgetshieldz.com/motorola-moto-x4-screen-protectors-cases-covers.html
Click to expand...
Click to collapse
You stated what areas are protected, but what do you think of it?
pizza_pablo said:
You stated what areas are protected, but what do you think of it?
Click to expand...
Click to collapse
If someone is looking to stay away from the scratches and doesn't want to show that something is been applied on the screen camera or body. They can go with this.
I am using Nillkin frosted case for Moto X4. It's perfect for those who hate bulky cases as I do. The fit is accurate, also it protects camera bump. Case quality is very good, no doubt it will last long.
Nillkin screen protector (clear) for Moto X4 was included in the box. I bought it from AliExpress for $4.59.
http://s.aliexpress.com/r2yIZ3UN?fromSns=Copy
(Now price seems to be increased, you may check other sellers for lower price)