The phone is relatively new and since it's not mainstream most carriers don't support it yet. Some people say they have VoLTE enabled and it works but I personally switched to Singapore EX and it seems VoLTE isn't detected at all so I started digging and it seems this issue is present in most Chinese phones. (https://forum.xda-developers.com/t/guide-activate-volte-and-vowifi-simple-and-clear.4116051/) In this thread they used the Qualcomm tool and exploit the bug in EngineerMode on OnePlus phones which we don't have an access to and since we can't root or unlock the bootloader we can't modify build.prop or change any system files.
-----Maybe it's my carrier, maybe it's the Singapore ROM so please if VoLTE and VoWifi works for you could you post here which country you're on, which ROM version and if you changed region before or not.------
First a warning: If you aren't tech-savvy, experiencing issues or want to potentially turn your phone in a paper weight do NOT try this at the moment. We do not have the tool to restore your phone back (wiping data might work but idk). You can send your phone to Oppo for repair but you might have to wait for a month or two.
I don't know if you need to unlock your phone from the other thread to have access to this mode(I did have it all decrypted during this test) but in addition to the *#808# engineer mode and *#*#4636#*#*(Where you can check if you have VoLTE enabled) I found we have access to *#36446337#.
In *#36446337# I managed to enter "Protocol test switch" -> "MBN TEST" and switch my profile from Common-Commercial(I think it was this one) to Commercial-DT-VOLTE. The phone rebooted and everything is fine but "MBN Validate" is giving me an error when I run it and I can't test if it works because I'm currently out of the country and my temporary SIM provider doesn't support VoLTE.
It's probably nothing and the error is because of the lack of developer files on the ROM but I need people who can test if these profiles act like the flashing from the Qualcomm tool in the thread mentioned above.
So once again if you don't have VoLTE enabled and are feeling a bit courageous - give it a try.
I think the problem maybe for those that changed to Pakistan build on Android 10 and then switched to Singapore ex to get ColorOS 11 and dual SIM meant that things like VoLTE do not work on those builds.
I did it a different way as wasn't bothered about dual SIM. I was on A.46 UK , waited for EU to get ColorOS11 , then switched to EUEX on sec5 and downloaded ColorOS11 c.57 through Belgium VPN.
VoLTE is working for me. it's not present in SIM settings( WiFi calling is) however when I look at my call log there is a VoLTE HD icon next to all my calls, so is working.
Since being on ColorOS11, I have tried several different regions on SEC tool, EUEX dual SIM, Singapore EX, back to GB CPW to check still works and now back to EUEX. Build number always changes to different region in about phone when I have made any changes and check however VoLTE has always remained working for me and is showing as provisioned in engineer mode.
I am from Germany and have a phone with Vodafone FW originally. I switched region to Singapore EX, than installed the Pakistan FW and got C.5 and C.6 via OTA. I switched the region to EUEX (DUAL SIM) and didn't receive the update to C.57, so I switched back to Singapore EX and got the update to C.57 when using VPN Hongkong, which was quite funny.
VoLTE and Wi-Fi calling is working fine with Vodafone, but you can't toggle it in the hidden service menu, it's just active! You can activate or deactivate Wi-Fi calling in the regular settings, but VoLTE is just there, you can't deactivate it.
Both Wi-Fi calling and VoLTE are shown in the bar on the top. With the former Vodafone FW, VoLTE was not shown with an icon, but it was nevertheless working.
Hy here T-Mobile shown volte and Vodafone don't shows but on the status bar there is the volte symbol
MeTheRebel said:
The phone is relatively new and since it's not mainstream most carriers don't support it yet. Some people say they have VoLTE enabled and it works but I personally switched to Singapore EX and it seems VoLTE isn't detected at all so I started digging and it seems this issue is present in most Chinese phones. (https://forum.xda-developers.com/t/guide-activate-volte-and-vowifi-simple-and-clear.4116051/) In this thread they used the Qualcomm tool and exploit the bug in EngineerMode on OnePlus phones which we don't have an access to and since we can't root or unlock the bootloader we can't modify build.prop or change any system files.
-----Maybe it's my carrier, maybe it's the Singapore ROM so please if VoLTE and VoWifi works for you could you post here which country you're on, which ROM version and if you changed region before or not.------
First a warning: If you aren't tech-savvy, experiencing issues or want to potentially turn your phone in a paper weight do NOT try this at the moment. We do not have the tool to restore your phone back (wiping data might work but idk). You can send your phone to Oppo for repair but you might have to wait for a month or two.
I don't know if you need to unlock your phone from the other thread to have access to this mode(I did have it all decrypted during this test) but in addition to the *#808# engineer mode and *#*#4636#*#*(Where you can check if you have VoLTE enabled) I found we have access to *#36446337#.
In *#36446337# I managed to enter "Protocol test switch" -> "MBN TEST" and switch my profile from Common-Commercial(I think it was this one) to Commercial-DT-VOLTE. The phone rebooted and everything is fine but "MBN Validate" is giving me an error when I run it and I can't test if it works because I'm currently out of the country and my temporary SIM provider doesn't support VoLTE.
It's probably nothing and the error is because of the lack of developer files on the ROM but I need people who can test if these profiles act like the flashing from the Qualcomm tool in the thread mentioned above.
So once again if you don't have VoLTE enabled and are feeling a bit courageous - give it a try.
Click to expand...
Click to collapse
I am in the same boat as you. I rebranded to Singapore to get ColorOS 11 update, to use 2 SIM and Call Recording, along with Theme Store, etc.
While on my previous phone (Xiaomi Mi9) I had VoLTE and VoWiFi and my carrier supports them and my SIM has that activated by my carrier, on Oppo Find X2 Pro it seems for them to work is needed special Modem Profile for the concrete carrier you use.
My Carrier is not listed at MBN Test Menu, I tried all the profiles available there, all Commercial ones and all Volte Branded ones and they are not giving me VoLTE and VoWiFi options available in Menu or VoLTE or VoWiFi functionality.
This method used to work on Xioami and Commercial EU Carriers profiles gave me the VoLTE and VoWiFi functionality with just Activity Shortcut access to this menu on Mi9 and simple dialer code to activate VoLTE and VoWiFi switch in Settings.
Oppo Find X2 Pro is not sold officially in my country and by all carriers here and that is why there is no Carrier Volte Profile for carriers from my country and thus it is not possible to activate VoLTE and VoWiFi with other Carrier Profile from MBN Test Menu.
Maybe if we find a way with a Dialer Code or some menu to activate the VoLTE and VoWiFi switch in Settings first this profiles from MBN Test menu will work...
I am out of ideas for now.
ytgbg said:
I am in the same boat as you. I rebranded to Singapore to get ColorOS 11 update, to use 2 SIM and Call Recording, along with Theme Store, etc.
While on my previous phone (Xiaomi Mi9) I had VoLTE and VoWiFi and my carrier supports them and my SIM has that activated by my carrier, on Oppo Find X2 Pro it seems for them to work is needed special Modem Profile for the concrete carrier you use.
My Carrier is not listed at MBN Test Menu, I tried all the profiles available there, all Commercial ones and all Volte Branded ones and they are not giving me VoLTE and VoWiFi options available in Menu or VoLTE or VoWiFi functionality.
This method used to work on Xioami and Commercial EU Carriers profiles gave me the VoLTE and VoWiFi functionality with just Activity Shortcut access to this menu on Mi9 and simple dialer code to activate VoLTE and VoWiFi switch in Settings.
Oppo Find X2 Pro is not sold officially in my country and by all carriers here and that is why there is no Carrier Volte Profile for carriers from my country and thus it is not possible to activate VoLTE and VoWiFi with other Carrier Profile from MBN Test Menu.
Maybe if we find a way with a Dialer Code or some menu to activate the VoLTE and VoWiFi switch in Settings first this profiles from MBN Test menu will work...
I am out of ideas for now.
Click to expand...
Click to collapse
I'm pretty sure they force disable most of this stuff with region profiles (/etc/oppoRegion* folders)
At this point I honestly care more about GDPR protection,VoLTE and removing tencent/heytap crap than call recording and theme store which I don't use anyway.
So my plan atm is to wait for Oppo to release android 11 .57 .ozips so that I can flash back to european firmware then I'll see if changing region to EUEX Dual-SIM works and it's limitations.
This method might help people on EU roms with VoLTE, and I'll test it myself in the future, but at least for now *#36446337# lets us adjust MTU, 4G bands and some other smaller network optimizations.
Okay I don't know where to post this but I found *#649010# and this is where it gets into the spooky territory. I never tried toggling any of the options but I think "Full-port switch" option lets us connect our phone to the qualcomm diagnose tool just like the OnePlus phones from the Carrier profiles thread. I'm just documenting this code here so we know we have an alternative to the OnePlus LogKit.apk option in our Oppo phones.
MeTheRebel said:
Okay I don't know where to post this but I found *#649010# and this is where it gets into the spooky territory. I never tried toggling any of the options but I think "Full-port switch" option lets us connect our phone to the qualcomm diagnose tool just like the OnePlus phones from the Carrier profiles thread. I'm just documenting this code here so we know we have an alternative to the OnePlus LogKit.apk option in our Oppo phones.
Click to expand...
Click to collapse
Interesting to find out what these options do.
For some reason, non of these codes work for me now after doing the region change a couple of times.
lukeaddison said:
Interesting to find out what these options do.
For some reason, non of these codes work for me now after doing the region change a couple of times.
Click to expand...
Click to collapse
We keep telling people - you gotta unlock every time you change region and even then the unlock lasts a fixed amount of time ex. 24 hours before it locks itself again
MeTheRebel said:
We keep telling people - you gotta unlock every time you change region and even then the unlock lasts a fixed amount of time ex. 24 hours before it locks itself again
Click to expand...
Click to collapse
Unfortunately, the tool no longer works for me to unlock, the codes don't work. I'm stuck.
lukeaddison said:
Unfortunately, the tool no longer works for me to unlock, the codes don't work. I'm stuck.
Click to expand...
Click to collapse
Works for me no issue. Try adding cloudflare dns to your setup, tether your phones connection to your pc while disabling your main connection and adding the number values from the original thread, fiddle with the loopback driver, disable firewall in windows or your router. Everyones connection and setup is different you just gotta find a way to make it work on yours.
Tl;dr it works you just got to tinker with it
ytgbg said:
I am in the same boat as you. I rebranded to Singapore to get ColorOS 11 update, to use 2 SIM and Call Recording, along with Theme Store, etc.
Click to expand...
Click to collapse
Did you have the call recording option right after you switched region? I changed to Singapore Ex right after I got the phone, didn't see that option. Then I upgraded to ColorOS11, still did not find that option.
Jennifer000 said:
Did you have the call recording option right after you switched region? I changed to Singapore Ex right after I got the phone, didn't see that option. Then I upgraded to ColorOS11, still did not find that option.
Click to expand...
Click to collapse
You have to give permissions to 'Recording' app, then open enable it in 'Call Settings'
Mitar00 said:
You have to give permissions to 'Recording' app, then open enable it in 'Call Settings'
Click to expand...
Click to collapse
Do you mean recorder App?
Already given all permission but still no call recording option, and the recorder only has cloud sync on its setting
Jennifer000 said:
Do you mean recorder App?
Already given all permission but still no call recording option, and the recorder only has cloud sync on its setting
View attachment 5480471View attachment 5480473
Click to expand...
Click to collapse
Look in your Oppo Dialer settings, should be there somewhere .
Mitar00 said:
Look in your Oppo Dialer settings, should be there somewhere .
Click to expand...
Click to collapse
No luck, but thanks anyway.
Related
So, my carrier suggests for themselves it's a proprietary solution they bake into their phone roms, and may well be. However, they've recently liberalized registration for this service which suggests they may be implementing broader access for devices.
Anyhow, I was just wondering - if we are to operate under the assumption that wifi calling works on my carrier and compatibility doesn't get in the way.... how would I actually activate it and verify that it is active? Ideally on this ROM, but if it's not too deviant, any process would be appreciated.
Thank you for any assistance.
I am using official RR oreo and wifi calling works perfectly fine with my carrier.
Heyyo! Your best option for testing it is to try out AEX or Pixel Experience as ShivaTehaPeddi is the guru of VoLTE, VoWifi and ViLTE and such. :good:
I'm unsure if he has the latest Canadian APN settings but my unofficial LineageOS 15.1 builds do include them.
I'm with Fido and when I tried it with Koodo Mobile both carriers I get IMS registration failed.
To check this? Enable VoLTE and VoWifi in your settings under mobile data.
Then go I to your dialer app and dial...
*#*#4636#*#*
It sometimes takes a few minutes to open if your phone is freshly booted.
Then in the menu select IMS status and hope for the best.
arpit1234567 said:
I am using official RR oreo and wifi calling works perfectly fine with my carrier.
Click to expand...
Click to collapse
With respect, that addressed literally nothing I asked.
I'm not on your carrier. I'm not asking if voWifi works generally. Etc. etc.
ThE_MarD said:
Heyyo! Your best option for testing it is to try out AEX or Pixel Experience as ShivaTehaPeddi is the guru of VoLTE, VoWifi and ViLTE and such. :good:
I'm unsure if he has the latest Canadian APN settings but my unofficial LineageOS 15.1 builds do include them.
I'm with Fido and when I tried it with Koodo Mobile both carriers I get IMS registration failed.
To check this? Enable VoLTE and VoWifi in your settings under mobile data.
Then go I to your dialer app and dial...
*#*#4636#*#*
It sometimes takes a few minutes to open if your phone is freshly booted.
Then in the menu select IMS status and hope for the best.
Click to expand...
Click to collapse
Sorry to only address this now, but I tried that and I just get a robot saying (with a seemingly Chinese accent, no idea if that's related or not): "Please enter 6 digit password for ... ip something .. account then press pound."
Any thoughts?
I really need WiFi Calling in order to reasonably use this phone for calls from my house due to a poor Network signal. There is no Wifi Calling option in Calls -> Settings or in Settings -> Network & internet -> Mobile network anywhere. Also when I do *#*#4636#*#* and go into Phone information Wifi Calling Provisioned option is grayed out.
Nope. Last time I saw wifi calling available was on the XZP. Wasn't an option for the XZ3, and still not an option for the Xperia 1. Try giving tmobile a call or maybe sony support and ask if they can add wifi calling support.
reiriop said:
I really need WiFi Calling in order to reasonably use this phone for calls from my house due to a poor Network signal. There is no Wifi Calling option in Calls -> Settings or in Settings -> Network & internet -> Mobile network anywhere. Also when I do *#*#4636#*#* and go into Phone information Wifi Calling Provisioned option is grayed out.
Click to expand...
Click to collapse
Option is here for me. Can you not flash a non branded firmware?
Mackay53 said:
Option is here for me. Can you not flash a non branded firmware?
Click to expand...
Click to collapse
Which frimeware is that ? Is that US unbranded
Nope, no wifi calling for me. I originally had the J9110 model (international dual sim, hong kong) but i recently flashed it with the US firmware. No dice, unfortunately. But since changing to the US firmware, I now get VoLTE and group message in Android Messages. It's a start.
Ya VoLTE is working fine and appears as provisioned in the hidden menu. So it seems like I will have to do something similar to what I did on the XZ Premium in order to get WiFi Calling...but I will wait until there is a DRM backup process.
reiriop said:
Ya VoLTE is working fine and appears as provisioned in the hidden menu. So it seems like I will have to do something similar to what I did on the XZ Premium in order to get WiFi Calling...but I will wait until there is a DRM backup process.
Click to expand...
Click to collapse
I see the same thing as you. How did you do it on the xz premium?
I had to root it and flash a zip that someone made for it, it might be possible to use the same zip but I'm not going to root mine until there is a DRM backup method. I barely every talk on the phone without LTE service so it's more so just really annoying not having WiFi Calling. I think a bunch of people were using the same zip for the 2017/2018 xperia phones to get it working.
I have XZ premium and XZ1 and wifi calling option is displayed when I use the Jio sim but not displayed when using Airtel sim (using Airtel broadband), so our phones do have wifi calling facility but working only with Jio sim, although Sony is not shown in the compatible phones list. I am in India.
That also stresses me out on My Xperia 5. Don't know If You talked about My Zips for VoLTE and the other Features but i didn't get it to work actually on Android 10. Possible that i just don't have the right Firmware atm (Customized EU / My Devices Firmware isn't Out yet), so i'm using Custom UK Firmware but that should also work... I'm a bit confused so i switched to GSIs which Made it even worse... Looks like we should start making Custom Vendors for our Xperias since the Methods changed over Android 7-8-9-10
Can you flash the dual sim model to work with a single sim firmware and does Wi-fi Calling Work later?
yes, that's what i did with my xz3. volte works with tmobile, but not att.
Hey guys been trying to enable VoLTE on my device it the international version CPH1919, I've tried *#*#4636#*#* and went in there and I see it but it's not turning on it just stays greyed out. Can anyone help ?
bosspow said:
Hey guys been trying to enable VoLTE on my device it the international version CPH1919, I've tried *#*#4636#*#* and went in there and I see it but it's not turning on it just stays greyed out. Can anyone help ?
Click to expand...
Click to collapse
I am looking for the same solution. You have achieved it?
I have the same model and I can't get the code to work in the stock dialer. How are you guys getting to open up?
Thanks
tyrich30 said:
I have the same model and I can't get the code to work in the stock dialer. How are you guys getting to open up?
Thanks
Click to expand...
Click to collapse
Same here. If you just want to access the network settings you can download an app like "ForceLTE" or similar.
I'm facing the same problem, I am appreciated if anyone have the solution?
Check your carrier and location
Whether you can use VoLTE or not depends on a few things:
* Your location, your account with your carrier, and the model of your phone.
* The carrier, carrier account, location, and phone model of the person you're calling.
* Some carriers support VoLTE only in certain cities or area codes. Contact your carrier to ask about your area and account.
moozer said:
Check your carrier and location
Whether you can use VoLTE or not depends on a few things:
* Your location, your account with your carrier, and the model of your phone.
* The carrier, carrier account, location, and phone model of the person you're calling.
* Some carriers support VoLTE only in certain cities or area codes. Contact your carrier to ask about your area and account.
Click to expand...
Click to collapse
Thanks for your reply, the problem is I have no problem to have VOLTE by using Galaxy S10 with same sim card and I couldn't find the volte "switch" in the oppo UI and couldn't turn on/off. As a result couldn't use the VOLTE function. Therefore I do think it is the firmware problem from Oppo.
I just thinking about if I could flash the official Taiwan rom of same global phone model to my current one for solving the problem. But I'm not sure if it is workable or not.
smallballl said:
Thanks for your reply, the problem is I have no problem to have VOLTE by using Galaxy S10 with same sim card and I couldn't find the volte "switch" in the oppo UI and couldn't turn on/off. As a result couldn't use the VOLTE function. Therefore I do think it is the firmware problem from Oppo.
I just thinking about if I could flash the official Taiwan rom of same global phone model to my current one for solving the problem. But I'm not sure if it is workable or not.
Click to expand...
Click to collapse
Ah. I have CPH1919 (UK) and only option is call over Wi-fi. There is also no way to get to the hidden service menu either like in every other phone I've had.
If you know for sure that Taiwan firmware has it, then I suppose, in theory, it would work providing that it is also definitely CPH1919 - any other variant has different partition structure. Be careful. Read around and let us know. Good luck
I have a CPH1919TW, it's using the same global firmware as CPH1919EX (even Oppo TW provides CPH1919EX ROM for download), the phone will ID itself as CPH1919TW.
squallho1 said:
I have a CPH1919TW, it's using the same global firmware as CPH1919EX (even Oppo TW provides CPH1919EX ROM for download), the phone will ID itself as CPH1919TW.
Click to expand...
Click to collapse
May I know if your phone have the VOLTE enable switch in the network manual?
Hey guys,
neither my Wifi Calling, nor 5G doesnt work on my Redmi K30 Ultra. Not sure whats the deal behind it, maybe its the Mediatek chip or that it doesn't pass Safety Net or that its not made for Europe.
Anyway: Can we hack this somewhere? Maybe modify some props or something and magically make it work?
Thanks so much! <3
More info: I've done the usual stuff like activating Wifi calling, VoLTE and 5G in settings and also disabled carrier check via number code. I also tried all 3 big carriers in germany
Telefonica/O2: Nothing works
Vodafone: LTE "works", it shows an HD icon at the top but Wifi Calling doesnt work and 5G doesnt either. Shows both VoLTE and Wifi Calling as enabled in Phone Info.
Telecom: Nothing works, but it shows in Phone Info that VoLTE and Wifi Calling is enabled.
@Mirardt
Per description the phone supports Wi-Fi calling, VoLTE and LTE, so I think it's not a chipset problem. Carriers will typically sell these data services with smartphones as part of a bundle.
I guess it is a problem with carrier ( data plan chosen ). You can try to contact your carrier and check if everything is correct from there end.
In no case your issue has something to do with SafetyNet API what is an anti-abuse API application developers can implement.
jwoegerbauer said:
@Mirardt
Per description the phone supports Wi-Fi calling, VoLTE and LTE, so I think it's not a chipset problem. Carriers will typically sell these data services with smartphones as part of a bundle.
I guess it is a problem with carrier ( data plan chosen ). You can try to contact your carrier and check if everything is correct from there end.
Click to expand...
Click to collapse
Hey there, yes everything is activated from the side of my carrier and also i spoke with vodafone technical support and they activated everything they could, reset the network etc.
Also both VoLTE and Wifi Calling work on the iPhone with all of the cards. So it has to be something on the phone.
jwoegerbauer said:
In no case your issue has something to do with SafetyNet API what is an anti-abuse API application developers can implement.
Click to expand...
Click to collapse
Ok this already is really nice to know!
Thank you for helping! @jwoegerbauer
Update: I have confirmation from german review website that both VoLTE and Wifi Calling worked for them on the K30 Ultra. Maybe that helps in identifying the problem?
Mirardt
Mirardt said:
Hey there, yes everything is activated from the side of my carrier and also i spoke with vodafone technical support and they activated everything they could, reset the network etc.
Click to expand...
Click to collapse
Sometimes they just block per device model (supporting only phones that were certified for their network) and you need to convince them to let you in
Or, you could (again) play with props like ro.product.manufacturer and ro.product.model to pretend you have some fancy Samsung - bcs if it shows enabled in the settings, it's likely blocked at the time of handshaking and negotiating to use the service
It's also possible to capture the UE Capabilites offer (see attachement for my LTE part) and response - I will try to find where was the URL with know-how and instructions
Edit:
https://mt-tech.fi/en/how-to-get-4g-supported-ca-combinations-from-your-android-phone/
zgfg said:
Sometimes they just block per device model (supporting only phones that were certified for their network) and you need to convince them to let you in
Or, you could (again) play with props like ro.product.manufacturer and ro.product.model to pretend you have some fancy Samsung - bcs if it shows enabled in the settings, it's likely blocked at the time of handshaking and negotiating to use the service
It's also possible to capture the UE Capabilites offer (see attachement for my LTE part) and response - I will try to find where was the URL with know-how and instructions
Edit:
https://mt-tech.fi/en/how-to-get-4g-supported-ca-combinations-from-your-android-phone/
Click to expand...
Click to collapse
I talked to a vodafone technical support guy and he said that everything is fine and open from their side. Also my phone runs with your fingerprints (Mi9T) for a week or so and it didnt change anything.
Do I understand it correctly, that all the methods you linked there only work with Qualcomm chips? Cause the K30 Ultra does have a Mediatek chip. :cyclops:
Mirardt said:
I talked to a vodafone technical support guy and he said that everything is fine and open from their side. Also my phone runs with your fingerprints (Mi9T) for a week or so and it didnt change anything.
Do I understand it correctly, that all the methods you linked there only work with Qualcomm chips? Cause the K30 Ultra does have a Mediatek chip. :cyclops:
Click to expand...
Click to collapse
If the doc is only about Qualcomm, you will need to Google for e.g. MTK bands UE Capabilities
But MTK was usually more open, people were even able to easily change IMEIs.
There used to be a code for MTK Engineering mode, with options to enable bands and so
zgfg said:
If the doc is only about Qualcomm, you will need to Google for e.g. MTK bands UE Capabilities
But MTK was usually more open, people were even able to easily change IMEIs.
There used to be a code for MTK Engineering mode, with options to enable bands and so
Click to expand...
Click to collapse
Ok do I understand correctly that UE Capabilities are parameters that my devices has that sends information if it can do 5G or VoWifi and so on?
After a bunch of Apps that refused to work with my phone (unknown device not supported) I did found one that looks promising. The problem is that I have only littly orientation and understanding. Can you see what setting might be relevent and maybe if we can get those UE Capabilities changed inside the app?
What I tried is switching the "Entitlement Status" of Wifi Calling on "Enable" (It was disabled as I opened the app), but nothing changed. The Entitlement server is left blank, maybe that could help?
Also I just swapped every possible thing from "false" to "true" inside ePDG Config, but it didnt help so I reseted it.
If you (or anybody else) could have a look and give me some direction I would grind it out myself!
edit: Upload doesn't work on this forum somehow, strange. Here is the Gdrive link.
Ok I just looked through every single option their is, screenshoting everything that seemed relevent.
There is band information that seems like it is what you mentioned and it is editable! @zgfg
Also a couple of other direct mentions of VoLTE, like props in IMS settings.
Mirardt said:
Ok I just looked through every single option their is, screenshoting everything that seemed relevent.
There is band information that seems like it is what you mentioned and it is editable! @zgfg
Also a couple of other direct mentions of VoLTE, like props in IMS settings.
Click to expand...
Click to collapse
Very interesting, (as expected) you can control many things on MTK ( too many)
For LTE bands, I think you need bands 1,3,7,20 and you don't need TDD bands.
For 5G, googling tells me that for Germany you need: n1,n3,n28,n78,n258.
Suggesting you to double-check for your operator and enable what's missing and reboot.
B20 might be available in a shopping center, or dense busy district
In the Call* and IMS-Registration* screensots, are all those params enabled or you need to open another screen for each (modes)?
On the IMS, I would put VoLTE to Default, not to CMW500 - seems to be a mode for testing equipment.
Also, you could try SMS over 3GPP or 3GPP2 (that means SMS over IMS but when you register to IMS), but check does it still work over cellular
Last screenshot says that it's not registered to IMS, but seems there are additional settings for IMS authentication (that's about registering to IMS - VoLTE is an IMS service)
I pretty much tried everything out you suggested and it didnt work. Thats why I waited to work on that until I freshly reset my phone with GApps Pico and I did that yesterday. During the Installation process there are 2 question came up:
1. There are Google Carrier Services I can install through play store. No clue what it is, does it matter?
2. I have found multiple interesting sounding apps in system/priv-apps like "engineermode", MtkCapCtrl", "MtkTelecom", "MtkTelephony Assist" and "MtkTeleService", the only one I can find in Apps is "engineermode" and i didn't manage to open it. I tried to install the other apks but it didnt allow it. Anything that might help us?
zgfg said:
Very interesting, (as expected) you can control many things on MTK ( too many)
For LTE bands, I think you need bands 1,3,7,20 and you don't need TDD bands.
For 5G, googling tells me that for Germany you need: n1,n3,n28,n78,n258.
Suggesting you to double-check for your operator and enable what's missing and reboot.
B20 might be available in a shopping center, or dense busy district
Click to expand...
Click to collapse
Unfortuantely I was wrong about being to change them, but i do have most bands enabled. Im in Hamburg City so I should have very good access here.
zgfg said:
In the Call* and IMS-Registration* screensots, are all those params enabled or you need to open another screen for each (modes)?
Click to expand...
Click to collapse
Another screen opens there, I put a couple of Screenshots as Example. Do you need more/all of them?
zgfg said:
On the IMS, I would put VoLTE to Default, not to CMW500 - seems to be a mode for testing equipment.
Also, you could try SMS over 3GPP or 3GPP2 (that means SMS over IMS but when you register to IMS), but check does it still work over cellular
Last screenshot says that it's not registered to IMS, but seems there are additional settings for IMS authentication (that's about registering to IMS - VoLTE is an IMS service)
Click to expand...
Click to collapse
Tried everything but it made no difference. Also tried IMS test mode on with and without SMS.
Also it keeps saying its not registered in PhoneInformation1.
Should we try to change those numbers in the VOLTE settings to something like this?
Edit: I activated logs telephony logs and somehow got a bug report without even calling somebody. Uploaded it.
Mirardt said:
Hey guys,
neither my Wifi Calling, nor 5G doesnt work on my Redmi K30 Ultra. Not sure whats the deal behind it, maybe its the Mediatek chip or that it doesn't pass Safety Net or that its not made for Europe.
Anyway: Can we hack this somewhere? Maybe modify some props or something and magically make it work?
Thanks so much! <3
More info: I've done the usual stuff like activating Wifi calling, VoLTE and 5G in settings and also disabled carrier check via number code. I also tried all 3 big carriers in germany
Telefonica/O2: Nothing works
Vodafone: LTE "works", it shows an HD icon at the top but Wifi Calling doesnt work and 5G doesnt either. Shows both VoLTE and Wifi Calling as enabled in Phone Info.
Telecom: Nothing works, but it shows in Phone Info that VoLTE and Wifi Calling is enabled.
Click to expand...
Click to collapse
wifi calling hardly ever works on foreign phones but my k30 ultra gets 5g on tmobile in my state.
Wifi calling hardly ever works on foreign phones but i get 5g on tmobile in my state , the k30 gets 3 bands that havent been listed , just get a mtk engineering mode app to see what bands you can work with.
I use the realme 7 pro on realme UI V1.0 and android 10, Build number RMX2170_11_A.34, Baseband version Q_V1_p14, kernel version 4.14.117, ColorOS V7. Using in Austria/Europe. Although both carriers (I use different ones with my two sim cards) support VoLTE and VoWIFI (it works well with Samsung S9+) I can't activate it on the realme because it is not even shown in the network settings. Is there anything I can do to make it work? I also tried changing the region of the device, but I always get invalid mmi code when entering *#3954391#. Also *#9434# does not work. I'm happy for any ideas, thank you!
U need to call your provider and tell them to do it, thats what i did and worked instantly
I'm on version RMX2170_11_A.36. Using in Germany/Europe. My carrier is Drillisch (o2 network). Both buttons are availble in settings. Only thing I'm missing is the VoLTE symbol in statusbar. VoWiFi symbol is present in the specific situation.
Senftrn said:
when entering *#3954391#. Also *#9434# does not work.
Click to expand...
Click to collapse
What are these codes for? Any source for this? Thanks
I also have no VoLTE option available. I am on Realme UI 2.0, build RMX2170_11_C.26. Before Realme7Pro I had Xiaomi phone and VoLTE was working there fine without any issues, so it is definitely activated on the operator side. Just Realme phone doesn't give me any option to turn it on...Any ideas how to enable VoLTE here?
lapist said:
I also have no VoLTE option available. I am on Realme UI 2.0, build RMX2170_11_C.26. Before Realme7Pro I had Xiaomi phone and VoLTE was working there fine without any issues, so it is definitely activated on the operator side. Just Realme phone doesn't give me any option to turn it on...Any ideas how to enable VoLTE here?
View attachment 5431207
Click to expand...
Click to collapse
have you alredy fixed this ?
redeemer01 said:
have you alredy fixed this ?
Click to expand...
Click to collapse
No, it seems that it would require the operator to activate VoLTE for our phone model and I didn't find any hidden menu where I could force enabling VoLTE.
I switched to Oneplus Nord 2, but I have the same problem - I have 2 SIMs from different operators, where one has VoLTE option visible and second doesn't (while it was visible in Xiaomi phone)...