Hi guys, at first sry for my bad English.
I have a big problem and i need help to solve this. One of my heater thermostat make problems. I started a firmeware update and make a big mistake. Now it is always in update mode. I found a solution for that problem with Remix OS.
Install a current (!) VirtualBox and VirtualBox Extension Pack for USB support DONE
Blacklist btusb module and possibly more specific device drivers like ath3k if it applies to your system to keep the Bluetooth USB device unoccupied (revert this later!); give chmod a+rw permission to the USB device file under /dev/bus/usb/xxx/yyy, see lsusb I skiped this step. I hope it was okay.
Install RemixOS in a VirtualBox VM, add a USB device filter to expose your Bluetooth chip to RemixOS DONE (Install Remix on Ubuntu 64bit Bluetooth is working fine and Remix OS show me the thermostat.)
Install calor BT on RemixOS, run it at least once DONE (app for the thermostat from the play store
Determine the device Bluetooth address: Open the device by unscrewing the four screws, then gently pulling the turning knob outwards, remove the cover; locate the "ADDRESS" QR code printed on the front of the circuit board; scan the QR code to retrieve the Bluetooth adress in form M001A22XXYYZZ (I had to take a picture, crop it and then run the QR scanner on the image); the Bluetooth address then is 00:1A:22:XX:YY:ZZ; replace the cover, again gently pulling the turning knob outwards, turn it to make it fit the turn encoder; screw the cover DONE MAC is M001A220EE2D5
Manually set up the calor BT configuration to address the bricked device. Save this as container.json, replacing all XX:YY:ZZ by the address determined above: {"clients":{},"devices":{"00:1A:22:XX:YY:ZZ":{"availableFirmwareVersion":null,"firmwareVersion":null,"groupId":"17f51411-4be0-4155-98f6-9a03bbde5681","groups":[],"id":"00:1A:22:XX:YY:ZZ","label":"Device","lastStatusUpdate":0,"lowBat":false,"unreach":false,"updateState":null,"operationLockActive":false,"temperatureOffset":0,"valvePosition":null,"type":"HEATING_THERMOSTAT"}},"groups":{"17f51411-4be0-4155-98f6-9a03bbde5681":{"channels":null,"devices":["00:1A:22:XX:YY:ZZ"],"homeId":null,"id":"17f51411-4be0-4155-98f6-9a03bbde5681","label":"Room","lastStatusUpdate":0,"lowBat":null,"metaGroupId":null,"unreach":null,"activeProfile":null,"actualTemperature":null,"boostDuration":0,"boostMode":false,"controlMode":"AUTOMATIC","maxTemperature":29.5,"minTemperature":5,"nextSwitchPoint":null,"profiles":null,"setPointTemperature":17,"windowOpen":null,"windowOpenTemperature":12,"type":"HEATING"}},"home":{"absenceEndTime":"","absenceType":"NOT_ABSENT","availableAPVersion":null,"clients":[],"connected":false,"currentAPVersion":null,"deviceUpdateStrategy":null,"ecoDuration":null,"ecoTemperature":0,"groups":["17f51411-4be0-4155-98f6-9a03bbde5681"],"id":null,"lastReadyForUpdateTimestamp":0,"location":null,"nonAbsenceGroups":[],"pinAssigned":false,"powerMeterCurrency":null,"powerMeterUnitPrice":0,"timeZoneId":"","updateState":"UP_TO_DATE","dutyCycle":null},"metaGroups":{},"weather":{"temperature":0,"weatherCondition":"UNKNOWN","weatherDayTime":"DAY"},"homeGroup":null,"inboxGroup":null} Maybe use http://www.jsoneditoronline.org/ to edit this. DONE change all the MAC address. I create the file container.json.
Now, install this configuration inside RemixOS: make sure the VM is shut down.
Mount the RemixOS VM image, first making the VM image available as a block device (using qemu-nbd from qemu-tools): modprobe nbd qemu-nbd -c /dev/nbd0 --partition 1 <path to RemixOS.vdi>
Now mount it: mount /dev/nbd0 /mnt
Copy container.json to /mnt/android-2016-06-30/data/data/de.eq3.ble.android/app_data/ (might vary depending on RemixOS version)
Unmount the RemixOS image: umount /mnt qemu-nbd -d /dev/nbd0
Boot up RemixOS; run calor BT; go to "Room", then "Device", then "Update firmware"
Firmware should be transferred (showing moving bars next to "UPD" on the device), then rebooted, device is then going to "InS" mode, turn it off and on again to enter date setup, etc.
up to step 7 I understood the steps so far. But now i'am lost and need help.
i hope somebody could help me to finish this solution.
Related
kaiser ubuntu port based on zubuntu by Omegamoon for Sharp Zaurus was successfully launched on HTC Nike!
Instructions:
1. download kernel
http://84.23.71.227/kerneloftheday/zImageUbuntu
2. download ubuntu basefiles and rootfs
3. place ubuntu.img, haret, initrd.gz and zImageUbuntu to Storage Card/ubuntu/
4. place this default.txt there too
Code:
set RAMADDR 0x10000000
set MTYPE 1724
set KERNEL zImageUbuntu
set initrd initrd.gz
set cmdline "pm.sleep_mode=1 mddi.width=320 mddi.height=480 lcd.density=160 board-htcnike-keypad.keypadlayout=1 board-htcnike-keypad.sticky_timer_time_ms=350 no_console_suspend"
boot
5. change board-htcnike-keypad.keypadlayout=1 to 0 if you have 20key nike.
6. run haret and press "Run", ubuntu & kernel will be loaded to login prompt, login with username root and no password, you will get root shell.
7. write
Code:
export TSLIB_TSDEVICE=/dev/input/event0
ts_calibrate
and calibrate your screen.
8. write startx and see LXDE running on your nike! you've got real linux box in pocket!
Note, rootfs for ubuntu needs 1GB of free space on your sdcard!
For now, you cannot work with screen, we have some difference from kaiser panel's, i.e. ubuntu gui is completely unusable, this thread were started to find out why.
based on this thread from kaiser forum.
Credits: dzo, Omegamoon, domy007, mblaster and guys from Rhodubuntu thread.
I dont get any response when i try to calibrate screen on niki 200
thats strange, it must work.
I will debug on touchscreen problems, but ubuntu running and that is great, now we have only input-devices problems, and this is more better than nothing.
Sounds great, but wouldn't it be better to try something smaller like puppylinux or Feather linux ?
zubuntu is only we have compiled for ARM and working with our hardware that starts X and tested on other htc's devices.
rzk333 said:
zubuntu is only we have compiled for ARM and working with our hardware that starts X and tested on other htc's devices.
Click to expand...
Click to collapse
Ok thanks for the information, did some reading before and was always wondering why they use ubuntu but this answer set things straight.
Greetz,
Great to see a full linux distro around for htc devices. I will fix the '_' tomorrow... Any other missing characters?
How is the speed of ubuntu? Is it very sluggish or usable?
'=' character maybe, for export line.
zImageUbuntu is updated (your link is still valid).
'=' and '-'are on '*'-button, '_' is Alt-
I have included the msm_fb_refresh and the keypad changes into my auto-updated-kernel, so you should be able to use the fresh kernels from my thread with ubuntu if you want recent updates (zImageUbuntu is not automatically updated).
got some progress,
1) msm refresh thread seems to disable sleep mode in android, thread polls framebuffer many times in second and drains battery.
2) linux logo on bootup must be disabled - logo gets over ts_calibrate's first crosshair point.
2) still trying to make touchscreen and tslib friends - i2c bus debug messages logs saying that touchscreen is connected and recieves data correctly.
found some data:
/dev/input/event0 - htcnike-kbd
/dev/input/event1 - htcnike-ts
but still no data from touchscreen...
rzk333 said:
got some progress,
1) msm refresh thread seems to disable sleep mode in android, thread polls framebuffer many times in second and drains battery.
2) linux logo on bootup must be disabled - logo gets over ts_calibrate's first crosshair point.
2) still trying to make touchscreen and tslib friends - i2c bus debug messages logs saying that touchscreen is connected and recieves data correctly.
found some data:
/dev/input/event0 - htcnike-kbd
/dev/input/event1 - htcnike-ts
but still no data from touchscreen...
Click to expand...
Click to collapse
Disabled msm refresh thread from the android kernels again. The kernel you linked in your first post is now automatically updated with anything new in the repository. Bootlogo is disabled, too. Good luck with tslib, let me know if when you need something else to be hacked into the kernel.
mblaster
I've just test the usb ether function in the zImage from the post
showthread.php?p=6675397
and it works just fine.
(Just when I had managed to make adbd works... but ssh is more reliable)
Thanks gTan64.
wow, that is good, now I can dump system state without hours of keyboard typing
I've managed to get internet by usb (cdc only) thanks to gTan64: just apply the patch from is post ("Debian on the vogue"), you can extract it from the download links.
And the TOUCHSCREEN WORK!!!!!!!
But you need to compile tslib from the tslib git (github.com/kergoth/tslib.git), the one in the rootfs from this post doesn't work.
Will make a more complete post later, I think.
Bye.
Ubuntu always shows me a black screen when I try to startup it!
What can I do make it work?
omg, I knew that something is wrong with tslib in this rootfs!
thanks for r&d, if you will make some packages & mans, I'll add them to first post.
Maybe you can upload some pics ?
But you need to compile tslib from the tslib git
Click to expand...
Click to collapse
I tried to compile - but no luck, autoconf fails to make configure...
I also uploaded debian rootfs and posted links in gTan's Debian on Vogue thread.
nothing happened last month?
Zen's Backtrack 5 For HD2 (and other) Android Smartphones
V0.3
----------------------------------------------------------
New app for loading this (and other) Linux Systems! - https://play.google.com/store/apps/details?id=com.linux.autoloader
Image and app support can be found here --> http://www.zenfulapps.com/
Packed - 640mb
Unpacked - 2.6gig (fits on 3.3 img now.)
--GRAB THE UPDATED SCRIPTS ATTACHED TO THIS POST, THEY ARE NOT PACKAGED INTO THE ZIP--
--Scripts are set to load from EXT4 partition, when i modify them for the .img's ill add them to the script pack--
--if you have .img mounting scripts from previous versions, they will work, as long as file names and directories match--
V0.3 Download
http://www.zenfulapps.com/Android/backtrack5-0.3.7z
(MD5 is still the same
MD5sum (of .7z file) - 9a4796f0ed96e03579c2b4a684d026f5
--------------------
Script pack contains
--------------------
btgo - mounts BT5, and askes how you would like to start, CLI or VNC
bts - stops BT5, and unmounts everything for it.
btl - used to login to bt5 after it has been mounted, to avoid all those "resource busy" messages
mkcore - directory installation and swap file creation
-------------
What you need
-------------
Rooted Android Smartphone
Linux on PC
Busybox installed on your device
SDcard adapter or reader, if neccesary
----------
Lets begin
----------
There are 3 different ways you can do this:
1. Fresh install on EXT4 Sdcard partition ( I HIGHLY recommend this method if possible, much better, a bit faster (no double loops to write to)
2. Create Fresh .img
3. Replace old BT5 system .img
=========================================
1. Fresh install on EXT4 Sdcard Partition
=========================================
This portion of the guide is to install BT5 on a FRESH EXT4 partition on your SDcard. Throughout this porcess, you will:
Backup your current sdcard (EVERY PARTITION, this is why we use PC-linux and not windows)
Fully erase and repartition your SDcard
Replace Android system and user data
Install BT5 on third partition
prepare system for chroot and VNC connection
----------------------------------------
Boot into your Linux operating system. **I DO NOT recommend using virtualbox or vmware, as drivers for usb and SDcard connections arent direct, things can go wrong.**
Shutdown your phone, and remove your SDcard. Do not use adb, or any other tools to do this.
insert your SDcard into your computer (adapter or reader yada yada) and mount every partition.
Make careful note of what is on which partition. safest way to back everything up is through the command line with the command
Code:
sudo cp -Rfvp /media/your-sdcard-partition/* /where/your/backup/folder/is
Do this for each partition, whether you have 1, 2, 3, or more.
In my case, my backup directory looks like this:
Code:
[[email protected] sdcard-backup]$ ls -l
total 12
drwxrwxr-x. 2 hookup-cellular hookup-cellular 4096 Sep 13 18:48 ext2
drwxrwxr-x. 2 hookup-cellular hookup-cellular 4096 Sep 13 18:48 ext4
drwxrwxr-x. 2 hookup-cellular hookup-cellular 4096 Sep 13 18:48 fat32
(ignore the empty directory sizes, my TRUE backup folder is MUCH more vulgar and i wont display it publicly, people may tear thier eyes out )
After everything is backed up, open your partition manager (in Gnome it is gparted, cant remember the name in others)
Navigate to your SDcard, and DELETE every partition. every one.
afterwards, recreate them using this strategy:
partition 1 - FAT32 size = total sdcard size minus ext2 and ext4 partition sizes
partition 2 - EXT2 size = 256mb, 512mb, 1gb, depending on how you like your apps2sd
partition 3 - EXT4 size = size you want for linux, minimum should be 4gb (mines at 10gb, i like my linux and got 3 different ones on it at the same time.)
When you are done, copy back your fat32 and ext2 stuff using the SAME COMMAND AS ABOVE (sudo cp -Rfvp from/here to/here)
Now, unzip/tar the .tar.gz package. I recommend extracting it to your pc before trying to put it on your sdcard.
Using the copy command above, put the extracted files onto your sdcard's EXT4 partition.
Double check the partition (navigate to it in nautilus or whatever filemanager your using) and ensure that it has the system copied over properly. You should see /boot /etc /root /sys so on and so forth, NOT just one folder with all of those inside of it.
Insert your SDcard, power on your phone, go to terminal emulator, and enter this:
Code:
su
cd /sdcard/scripts
sh mkcore
Swap file is damn near neccessary if your planning on using any GUI tools (armitage, zenmap)
Your directory structure is now in place, swap file created, and you start BT5 by typing (from /sdcard/scripts OR /data/linux):
Code:
sh btgo
=================================
2. Fresh Image Creation
=================================
for this, we use the dd command and mkfs.ext4 command.
Code:
dd if=/dev/zero of=/path/to/where/you/want/the/img bs=1M count=3300
Change this command as needed, running it as is wont do anything good. Change the of= to where you want your img to be located.
next is mkfs.ext4
Code:
mkfs.ext4 /path/to/where/you/want/your/img
select yes when it cautions about "not a block device"
When this is finished, mount it using these commands:
Code:
su
-your password-
mkdir -p /mnt/bt5img
mount -t ext4 /path/to/your/img /mnt/bt5img
now, extract the BT5 package to a place on your Computer. When finished, run this command:
Code:
sudo cp -Rfvp /path/to/bt5/core/* /mnt/bt5img/
changing parameters accordingly.
After this, copy the .img to /sdcard/bt5 and run the start scripts from your terminal emulator.
================================
3. Replace Existing Image
================================
Mount your bt5 image, erase what is inside of it, and copy in the new system:
Code:
su
-your password-
mkdir -p /mnt/bt5img
mount -t (your ext type) -o loop /path/to/your/bt5/img /mnt/bt5img
rm -Rfv /mnt/bt5img/*
cp -Rfvp path/to/bt5/core/* /mnt/bt5img/
unmount your .img, place it on your sdcard, and your all set.
==============================
Changes in v0.3
==============================
- Trimmed alot of fat, fits inside of 3.3 image now, though space is SEVERLY limited (removed CUPS and sound stuff, who needs to print from within thier phone anyways?)
- various small changes for performace improvements.
- a few new tools installed, but not tested
- restored my personal version that i nuked. It works now.
NEW STUFF TO COME, STAY TUNED!!!
First off, My apologies for starting a second thread on this, I've made ALOT of changes and i feel the first thread is dead and useless. (Reprimand me if needed
-pics coming once I find my camera could be a small while-
---------------------------------------
Backtrack5 for HD2 - v0.2
Customized by z3n
My goal: the perfect stealth
tool in your pocket
just one tap away
---------------------------------------
========================
Codename
Squeaky Wheel
========================
Updated, check second post for changelog
========================
DOWNLOAD
========================
Please use the scripts attached at the bottom of this post instead of the packaged ones, and i havent had a change to update the full image zip with it (uploads take a while )
V 0.2
Part 1 - http://www.megaupload.com/?d=D0MQVAS4
Part 2 - http://www.megaupload.com/?d=M2MRYLAH
MD5 - 06225e18cdbfee6f88daf7e9ee3a1163
SHA1 - eeba19e53565a1643703cf8938be2f8cfc12db9a
V 0.1
Part 1 - http://www.megaupload.com/?d=83B22Y00
Part 2 - http://www.megaupload.com/?d=SB98AA19
mirror - (NOT interchangeable)
Part 1 - http://www.megaupload.com/?d=HU320Z81
Part 2 - http://www.megaupload.com/?d=QN9C560Z
Checksums of bt5.img
MD5 = 863e6db99e5207a81ad0df7d13998235
SHA1 = c84d8f27df8b9b51059e5a6b09e65853f11de970
7zip required to extract.
Just over 1gb packed, unpacked is 4.9gb.
========================
INFO
========================
This is my first release of a customized, working, mostly stable BT5.
Many things have been added, taken out, and configured to be used within the Android system. For a full list, please see the bottom of this post.
Mounting is different than most other linux .img installations, allowing for a full (and expandable) image.
V 0.2 Now has a swap file created when you run the mkdirectory script. This swap file is necessary, as with all my tests, When you run VNC with most of the major tools, there's a high chance of the phone running out of memory (im running no extra apps, completely stock Hyperdroid)
(if you have a swapfile already, you can say no to creating another, just make sure that the file is located at /data/bt and named btswap.)
**This image is in ext4, make sure your kernel supports it!**
**Everything tested on Hyperdroid-CM7 by pongster**
==============
INSTALLATION
==============
You need:
-Full Nandroid Backup in case something goes batty
-16gb HD2
-ext4 support on your ROM/kernel (lost my ext2 image due to my own stupidity, will create another matching one later)
-Linux on PC (to create the ext4 partition)
-Busybox (from market)
-VNC Viewer (from market) (optional)
FAT32/EXT4 Split card
---------------------
1.
Back up your HD2 and SDCard to safe places (off of the phone and sdcard)
2.
Boot your linux installation and open partition manager. erase all the partitions on yor SDcard. Then create them in this order.
1. FAT32 - size of this is total sdcard size minus 6.5g (for bt image) minus 100mb for aps2sd
2. ext2 - 100mb
3. ext4 - 6.5 gb
3.
Copy the bt5.img to the root of your third partition.
copy the bts folder to the root of your FAT32 partition.
4.
if this is your first time using this script/image, run the mkdirectory script first with
Code:
su
sh /pathtoscripts/mkdirectory
Load up your android terminal and type
Code:
su
cd /path/to/scripts
sh go
5.
Now it asks you if you want to log in to the console or start vnc automatically. (check log for port, usually 5901 or 5902)
DEFAULT VNC PASSWORD IS: toortoor
DEDICATED SDCARD
----------------
Same as everything above, minus the FAT32 partition.
"sh ded"
starts for dedicated SDcard instead of
"sh go"
Proper Shutdown Procedure
=====================
Stop script has been modified to shutdown backtrack and all of the (usual) programs that stop things from unmounting properly.
Exit any VNC connection you currently have.
1. Run sh stop (from your scripts location)
2. Reboot phone as a precaution.
One thing i did personally to make this easier was load the scripts onto /data/bt, so switching SDcards or locations doesnt matter.
(I also changed the terminal start directory to my scripts folder easy quick access)
=======================
Main Features I've gotten to work
=========================
-Clean mount/umount, as long as VNC and MySQL are killed BEFORE exiting the chroot - stop script kills these now
-Apps no longer disappear for good with sdcard removed, only disappear until SDcard is reinserted (apps2SD/loop device problem, any ideas?)
-MySQL for metasploit
-Metasploit working
-Armitage working, missing some "Attack" options (looking into it)
-Zenmap installed
-OpenVPN installed
-Traffic analysis possible with tcpdump (local only)
-Enables possibility for FakeAP attacks
-macchanger works (kinda, phone needs a reboot for original MAC to return)
-Armitage Launcher placed on Desktop (takes a while to load, be patient)
-Terminal Launchers in various places (updating may randomly remove your terminal, synaptic placed on desktop as standby to redownload terminals
-guake installed (drop down Terminal, makes commands easier to see while working) (not configured to a key yet)
This probably works with other Android phones too. If you change the scripts, and as long as it has a external SDcard you can partition.
if your using a different phone, this is untested unless specified otherwise.
-boot and shutdown scripts run clean as long as VNC and MySQL are shut off(in almost all cases)
@ XDA
http://forum.xda-developers.com/show....php?t=1152994
PASSWORDS
------------
MySQL - user: root pass: toor
VNC - User: root pass:toortoor
sys pass - user:root pass:toor
(I know, standard ones, but this should answer a few questions)
===============================
Thanks
===============================
anantshri - for the original scripts and BT5 img for android
BT dev team - (of course )
and all of you
===============================
Information, bugs, and oddities
===============================
One important thing, While performing heavy operations, its normal for your screen to not turn on for a while if it turns off. Dont panic, just give it some time to finish whatever you were running and your phone will be back to normal again. DO NOT PULL THE BATTERY UNLESS ABSOLUTELY NECESSARY.
To avoid this, get wakelock (known to cause problems) or set your screen timeout to some large number.
Swap file will help with alot of this.
These are the features I've tested out so far.
No major changes to anything, (except new packages) just configuring everything i see.
If you find anything you want added in or that is acting odd, please let me know. Same goes for if you fix something!!
Overall
-------
-Repo's activated, most things work (upstart processes fail, for now)
-startvnc and stopvnc no longer give that pesky USER error
-startvnc starts mysql database for metasploit
-stopvnc stops mysql (mostly, invoke ps -A and look for mysqld. Kill it with fire(-9) if need be)
-network traffic is capture-able with tcpdump, with wifi hotspot activated
-working on adding in a swap partition on sdcard (if possible)
-openoffice installed
-openVPN installed (the quieter you become...)
-Removed Zoho Web services
MySQL
-----
default user - root
default pass - toor
-Starts automatically with startvnc
-stops automatically with stopvnc
-start manually by invoking "mysqld"
-Only runs as root (for now)
-Console hangs when it is manually loaded or shutdown, service continues running though. killall --signal 9 mysqld if needed.
Metasploit
----------
-Loads up alright (45-90 seconds)
-MySQL already set as default DB
-Must manually connect to MySQL DB each instance of metasploit by invoking (from msf) db_connect root:[email protected]
-working on a possible way to limit cpu consumption to prevent system hangs(cpulimit does some nasty things)
-So far, this is the only connection string ive been able to get to work: root:[email protected]
Armitage
--------
-Takes forever to load (30 seconds for connect screen, 4 minutes or so for main client)
-Causes system hangs frequently (to minimize this, leave the vnc server on your screen, and set the display timeout to 10 minutes-switch it back when done to conserve battery life)
-So far, this is the only connection string ive been able to get to work: root:[email protected]
-Can Crash phone if running too big of an operation (Max Phone memory problem, fixed in v.2 with swapfile added)
Zenmap
------
-Slows phone down (incredibly bad with more complex scans, of course)
-Some Complex scanning options can crash phone (Nothing damaging has happened)
-will attempt to throttle cpu usage in the future
-Can Crash phone if running too big of an operation (Max Phone memory problem, fixed in v.2 with swapfile added)
Aircrack-ng suite
-----------------
-Aircrack-ng works
-Airodump-ng doesnt work (needs monitor)
-Airdecap-ng untested
-Airdecloak-ng untested
-Airbase-ng doesnt work (needs monitor)
-Airmon-ng doesnt work (needs monitor)
-Aireplay-ng doesnt work (needs monitor)
-Airdriver-ng doesnt work (yet)
-Airolib-ng works (doesnt do anything yet)
-Airserv-ng doesnt work (needs monitor)
-Airtun-ng doesnt work(needs monitor)
Plus lots of stuff for the future, stay tuned!!
http://forum.xda-developers.com/show....php?t=1152994
In the future
=========
-nessus
-Booting via HD2 Toolbox by d4n14l (sp?)
-Custom kernel (WAYYYY down the road, but working on it)
and more
--Copyrighted by z3n, 2011
(just kidding, but it looks good )
Looks good will give it a go.
Thanks for sahring
I we could get our wifi card into monitor mode --> awesome!!!!
Thanks to z3nful & everyone made this possible!
Enjoy everyone
The next release is going to be faster, stabler, and more useful
I'm also working on a round-about way for packet injection and monitor mode
Stay tuned
Sent from my Hyperdroid Pocket Laptop
cool.. good job man..
Are you trying to patch the wifi drivers ? =D
Holy crap.....this is a dream in the making Bring on monitor mode and packet injection
I've done some researches.. and found out that many devs have tried making the driver to work on the Monitor mode.. but they failed to do that.
It looks to me that Backtrack on HD2 is kinda useless.
Not useless, just last night I ganked my roommates computer with my phone
As far as monitor mode and injection go, sadly, they may be right that its not possible, but I got some ideas that may make it work, I just need to hammer out some kinks in BT first
And who needs monitor when you can fakeAP?
"Make them hand you the keys and you don't have to break their Window(s)™"
Sent from my Hyperdroid Pocket Laptop
A m a z i n g
Next release is going to be even better this 5gig image is almost full, so I'm going to expand it to 6gig, along with instructions on how to expand your own image if that's to large or want even more space.
Btw, Wine should be good to go in the next one
stay tuned!!
Sent from my HD2 "Pocket Laptop"
I would love to see some Sceenshots (or better: a video) here!
Lol will do, gotta go find my 10 year old Polaroid I've been using this phone or all my pics and videos, so this could be tricky
Sent from my HD2 "Pocket Laptop"
good to see development beyond just starting up the image... I would be taking some pointers from here for my device too....
hope you don't mind that....
Not at all, I've been trying to track down your name again so it can add you to the credits part, as the basis of the scripts was yours lol, I just changed the loops and mounting structures around a bit, and added some stability checks.
The scripts for this image are slightly out of date but I got new ones going up once I have time they should fix a few of the small eerrors people get while mounting
My next version is a little ways out (works gotten crazy busy lately) but it'll be out eventually
Sent from my HD2 Pocket Laptop
Not Booting!
Hi Thank you for sharings this up!!! this is like a dream for alot of people.
i have followed all your steps but i have a problem when i run the scripts, the folders dont get created because when i run go i get a bounch of folder not found.
my SD card had some differences is a 16GB
with
Fat32
Ext-sd/ EXT2 -->1GB
EXT3 --> 100MB
EXT4 --> 6.5GB
could this setup causing the script to look on the wrong partitions? i have alot of time with out playing with Shell scripting but i would like to know if that is the place i should start looking for a fix
-edit- just double checked (forgot scripts were on my phone... its been a long week lol) and you should just need to change the mount -t ext4 /dev/block/vold/179:3 to /dev/block/vold/179:4
Also, did you run the new mkdirectory script? If you have the one packaged with the image its out of date. The attachment on the fist post has the updated ones
Ignore all mmcblk's
For another "buffer" partition, you need t point the sdcard parts (mmcblk0p* and vold/179:*) to what yours are in /dev/block. In your case I think you just need to change any vold/179:3 to 179:4. If you go to /dev/block/vold it will have folders from each partition (they are numbered 0 and up, but 1 would be your fat32, 2 is ext2 so on and so forth)
When I'm near my computer ill figure out the full ones for you
Sent from my HD2 Pocket Laptop
can I get it for Htc desire..??
It should work, as long as you have a big enough sdcard, your phomes kernel suppers ext4, and you might have to change a few small variables
Sent from my HD2 Pocket Laptop
This is some of the info that I have put together and I figured it may help some of you also. Let me know if I need to add anything. Looking forward to working with this device. Hopefully the Devs will take an interest in it also. With these hardware specs I feel like they will. Anyway, carry on............
Dev/Config/Soft/Tools
CyanogenMod team Touchpad port
HP Site
SDK - Multiple Platforms Instructions
Command line tools
Java - WIndows 32 and 64 Bit Instructions
****Note - Be sure to add the Java Bin path to your Environment Variables PATH
Java - Linux
Bluetooth with Non-WebOS device
Enabling Developer Mode (Rooting)
How To: Connect TP to network sharesHW
Exploded and PCB
Quick sum up/start up guide Thanks KameoRE
Bill of Materials
Specs 16GB
Specs 32 GB
Repair Manual / Teardown
Comparisons
Extra info
Enabling Developer Mode (Rooting)
In general, simply installing the Palm SDK gives you everything you need for full access to the Linux operating system on any webOS device. There is no special "rooting" or "jailbreaking" process. Simply installing the SDK provides you with unlimited access to the Linux operating system.
Download & install the Palm SDK for Linux, OS X or Windows.
Enable developer mode on the HP Touchpad:
Launch Device Info and tap its top-left menu.
Select "Custom Application..." and type in: ##3386633#
In the application, move the Developer Mode slider to the On position.
Tap Reset the Device.
When reset is complete, Developer mode is enabled.
Plug the device into the computer via the USB cable, and just close out the USB storage mode thing.
The next step varies:
Mac OS X / Linux: Type novaterm into terminal to directly access the Linux command line for the HP Touchpad.
Windows: you will need to download and install a novaterm program.
On Windows 32-bit, download novacom-win-32.tgz and install novacom with NovacomInstaller_x86.msi.
On Windows 64-bit, download novacom-win-64.tgz and install novacom with NovacomInstaller_x64.msi.
Then, just like the Mac and Linux users you can just type novaterm.
At this point you will have a window with a prompt that says [email protected]: or something similar.
You are now logged in as root on your webOS device and can do anything you would normally do on a Linux device.
DISCLAIMER: We cannot be held liable for any loss of data, damage, bricking, or other malfunctions of the device. We solely provide the information needed to achieve root access.
This quick sum up/start up guide might come handy:
http://forums.precentral.net/hp-touchpad/293028-new-touchpad-heres-your-get-started-guide.html
[Q] What is wrong with my touchpad?
RESET: Hold Power Button & Home Button until the tablet resets.
Doing the above solved the below issue.
My touchpad won't turn on I used it until it had about 30 % battery last night, but didn't put it to charge. When I woke up this morning, it was at 28% battery. I used it to check facebook and xda, locked it and put it down to watch the price is right but when I went to use it again, none of the buttons unlocked it. I plugged it into mulitple outlets and held the power button for about 30 seconds each time, but nothing is happening I don't know what to do. Can anybody help?
Click to expand...
Click to collapse
solution #2
this happened twice:
plug it in to pc
open webos quick install
tools - command line
type "reboot" and hit enter
Bill of Materials
$318 Bill of Materials
Comparisons
Comparisons
Exploded and PCB
Exploded and PCB
First non-webOS phone to be fully tetherd with HP TouchPad
First non-webOS phone to be fully tetherd with HP TouchPad
Worked for me, I had to fool with it a couple of times to get it to work. My screenshot is attached
The messaging does not work but the phone calls do.
How To: Connect TP to network shares
How To: Connect TP to network shares
spud101
Member
Join Date: Jun 2004
Location: Netherlands
Posts: 574
Likes: 34
Thanks: 43
Thanked 69 Times in 34 Posts
Updated (Sep 7th 2011):
Rewritten to include a method for stock kernel, make shares usable for KalemSoft Media Player & automount at (re)boot. Thx to everybody who contributed to this thread! (Under construction, finished later)
Updated (Aug 9th 2011): processed some comments from this thread and the fact that uberkernel now also supports CIFS (& NFS).
Prerequisites:
- HP Touchpad, webOS 3.0.2 or later.
- One of the following Kernels:
---- Stock kernel
---- Uberkernel 3.0.2-52 or later (Next to support for CIFS & NFS this kernel also supports UTF-8. More info here: WebOS Internals Uber-Kernel
---- F15C,.. (completed later)
- Terminal access to your TP, either via webOS Quick Install or Xecutah + Xserver + Xterm (install from preware)
- Internalz Pro with show hidden files set to yes
Three parts:
This guide has three parts:
Basic Mounting
Mounting with shares visible in apps like Kalemsoft Media Player
"Sticky" mounting: Auto mount at (re)boot
Definitions:
hostIP = IP address of the computer or NAS you want to connect to. You can use hostnames too, but need to also edit /etc/hosts then.
sharename = The share name you want to connect to as configured on your computer/NAS
mountpoint-path = as discussed above, e.g. /mnt/nas
cifs = type of filesystem to mount (cifs is better version of smbfs, I've been told)
auto (or can also be noauto) auto/noauto determines if the share is mounted automatically at startup.
username & password = share login credentials. There are probably safer ways to do this instead of having this plain text on your device, anyone can tell me how to do that?
rw = access mode, in this case read & write, other possibilities exist too
The numbers have someting to do with filesystem check at boot.
1a: Basic Mounting (without fstab)
- Create a mountpoint, a path where the share will be accessible, e.g. /mnt/nas or /mnt/media/internal/nas I used Internalz Pro in master mode for this.
- In a terminal type:
mount.cifs //<hostIP>/<sharename> <mountpoint-path> -o username=<username>,password=<password>
Example: mount.cifs //10.0.1.26/DataVolume /mnt/Shared -o username=foo,password=bar
1b: Basic Mounting (with fstab, not supported by stock kernel)
To be finished later
2: Mounting with shares visible in apps like Kalemsoft Media Player
To be finished later
For now please refer to:
Road to Success - How to allow NAS to show up under /media/internal on Touchpad Apps?
How To: Connect TP to network shares
How To: Connect TP to network shares
3: "Sticky" mounting: Auto mount at (re)boot
To be finished later
For now please refer to:
Road to Success - Mounting SAMBA/CIFS Permanently on Touchpad
-------------------------------
Original post:
In short: The stock kernel on a webOS 3.0.2 Touchpad does not support CIFS. Or at least I didn't get it to work just the same way I do get it to work out of the box on a 1.4.5 Pre-.
Then I saw this thread: F15B & F15C test kernels
It says CIFS support! So I hesitantly installed this experimental F15C kernel, quickly ran Govnah to set max speed to 1.5 GHz (I don't want no real overclocking beyond this speed). But, YES, it does work, I now can access my NAS!
After I initially posted this thread webosinternals also added support for CIFS (& NFS) to the uberkernel (as of version 3.0.2-36). Thanks a lot for that guys!!
So how to go about:
- Install the F15C kernel from the testing kernel feed
The rest is standard linux stuff for mounting Samba shares:
- Create a mountpoint, a path where the share will be accessible, e.g. /mnt/nas or /mnt/media/internal/nas I used Internalz Pro in master mode for this.
- Open /etc/fstab again you can use Internalz Pro in master mode for this
Add a line:
//<hostIP>/<sharename> <mountpoint-path> cifs auto,username=<username>,password=<password>,rw 0 0
hostIP = IP address of the computer or NAS you want to connect to. You can use hostnames too, but need to also edit /etc/hosts then.
sharename = The share name you want to connect to as configured on your computer/NAS
mountpoint-path = as discussed above, e.g. /mnt/nas
cifs = type of filesystem to mount (cifs is better version of smbfs, I've been told)
auto (or can also be noauto) auto/noauto determines if the share is mounted automatically at startup.
username & password = share login credentials. There are probably safer ways to do this instead of having this plain text on your device, anyone can tell me how to do that?
rw = access mode, in this case read & write, other possibilities exist too
The numbers have someting to do with filesystem check at boot.
- Save the file
- Open a terminal
- type in this command:
mount -t cifs //<hostIP>/<sharename> <mountpoint-path> -o username=<username>,password=<password>
No idea whether all the -o options are still needed, as they are in the fstab line already as well.
Apparently mount -a should also mount your shares inside fstab. But for me that didn't work, maybe because I have it set to noauto.
This should do it.
Unmounting as follows:
umount <mountpoint-path> e.g. umount /mnt/nas
Note: as soon as you have a kernel running that supports CIFS, you can also use the xt tools. See this thread and the threads referenced inside it. samba filesharing - install/support thread
The xt tools will take over all the fstab editing and directory creation.
I agree this is still cumbersome. On an Android phone for example this is buildin in every decent filemanager. So I really, really hope that either or both Gemini and Internals HD will have some easy solution for this (both configuring and the actual mounting/unmounting). Or a solution straight from HP, this is also aimed at enterprise market after all!
Last edited by spud101; 09/08/2011 at 07:41 PM.
Thanked by 60milesmile, cookie_42, El_Titi, flyers333, ichi2k, Major Payne, mivoligo, Nightburn, obarthelemy, PF Graham, phil71, pre101, RickNeff, runner77, sf3000, sjp770, sps_2k1, tabaloos, teng_lin, thomaz, timjhenry, tlaswell
Weird shortcut to USB mode
Has anybody else seen this?
While connected to PC in "just charging" mode I reached out and accidentally hit the Volume Down and Power buttons at the same time. The TouchPad instantly switched to USB Storage mode.
Interesting behavior and I couldn't seem to find any mention of it anywhere.
PreCentral had it as a tip on their web site about a week ago and I spotted it there - http://www.precentral.net/access-usb-mode-touchpad.
Quite a few other useful titbits crop up on there - it is worth following. I use the webOS News app from the App Catalog. That gives heads-up on the free software codes as well.
dmarchant said:
PreCentral had it as a tip on their web site about a week ago and I spotted it there - http://www.precentral.net/access-usb-mode-touchpad.
Quite a few other useful titbits crop up on there - it is worth following. I use the webOS News app from the App Catalog. That gives heads-up on the free software codes as well.
Click to expand...
Click to collapse
LOL, I think you mean "TIDBITS."
Too bad there is no reverse version of this.
I did a search and have found similar threads. However, people seem to have been intelligent and back up stuff or installed recovery apps before screwing around with their phones. I did not.
I have a Samsung Note3. Kit Kat 4.4.2 installed OTA once I had it up and running. I rooted it. However, the version of Kit-kat has a famous issue in that it would not allow apps to write to the SD card. I found a site with manual instructions to edit the platform.xml to overcome this issue. The site is as below:
winaero.com/blog/unlock-external-sd-card-writing-for-all-apps-in-android-4-4-kitkat/
However, something went awry after rebooting. I could not see anything on my SD card and I was unable to edit the platform.xml. A solution seemed to be to flash the ROM (using ODIN 3.07). I did this and currently have Baseband version N9005XXUENB1 and Build Number KOT49H.N9005XXUENB7
However, the still has lots of issues. I can stick in a password on wifi and connect to the network but it does not actually communicate with the internet. The H with up and down arrows appears for 3g connectivitiy but also does not work. Bluetooth does not work. Youtube has stopped working errors are common. I am unable to install any apps as cannot use play store, etc. I have pictures and mp3s on my SD card but gallery comes up empty as does music app. The only "file explorer" I seem to have is "my files" app. It comes up as empty (although it shows Total storage available for both SD memory and device storage as using 25/32 and 22/29 respectively.
I am guessing that flashing the ROM did not remedy the corrupt platform.xml in the permissions folder. I think the folder path was etc/permission/platform.xml although am not an expert with android. I was hoping someone might be able to give me a solution to fix the issue. Preferably a completely fresh and clean wipe type solution. Although as I am a "newbie" the greater the simplicity of the solution the better.
Apologies for the length of this issue!
T
laconical said:
I did a search and have found similar threads. However, people seem to have been intelligent and back up stuff or installed recovery apps before screwing around with their phones. I did not.
I have a Samsung Note3. Kit Kat 4.4.2 installed OTA once I had it up and running. I rooted it. However, the version of Kit-kat has a famous issue in that it would not allow apps to write to the SD card. I found a site with manual instructions to edit the platform.xml to overcome this issue. The site is as below:
winaero.com/blog/unlock-external-sd-card-writing-for-all-apps-in-android-4-4-kitkat/
However, something went awry after rebooting. I could not see anything on my SD card and I was unable to edit the platform.xml. A solution seemed to be to flash the ROM (using ODIN 3.07). I did this and currently have Baseband version N9005XXUENB1 and Build Number KOT49H.N9005XXUENB7
However, the still has lots of issues. I can stick in a password on wifi and connect to the network but it does not actually communicate with the internet. The H with up and down arrows appears for 3g connectivitiy but also does not work. Bluetooth does not work. Youtube has stopped working errors are common. I am unable to install any apps as cannot use play store, etc. I have pictures and mp3s on my SD card but gallery comes up empty as does music app. The only "file explorer" I seem to have is "my files" app. It comes up as empty (although it shows Total storage available for both SD memory and device storage as using 25/32 and 22/29 respectively.
I am guessing that flashing the ROM did not remedy the corrupt platform.xml in the permissions folder. I think the folder path was etc/permission/platform.xml although am not an expert with android. I was hoping someone might be able to give me a solution to fix the issue. Preferably a completely fresh and clean wipe type solution. Although as I am a "newbie" the greater the simplicity of the solution the better.
Apologies for the length of this issue!
T
Click to expand...
Click to collapse
Sounds like a bit of a pickle. Since you know that Odin is working and the firmware you have at least flashes correctly, I'd consider installing a custom recovery, backing up EFS folder (and the rom too, just in case there is some weird issue with Odin the 2nd time around) , then wipe everything - /system included. This will make your phone not be able to boot up at all because it will wipe the OS off. Then just boot directly to Download and redo the firmware flash. Something else to consider since you do have the international version, is that some of the firmwares you install might be more carrier or region specific, so there might be a better option to install. I know that there is a some slightly newer version that has NC2 in it as I was trying to fix one of these phones the other day that could not register on any network and ran across that build. Do you remember the build number of the software before you started modding?
Hello. Thanks for the reply.
I am going to ask what are probably very obvious questions but I am a little out of my depth.
1) What does installing a custom recovery involve?
2)How would I backup the EFS directory? When I had ES file explorer I would have been able to try and find it. However, as it is I do not know how to find the directory and back it up. I have connected the phone to a windows laptop and it shows up as note3 but there are no folders or files visible in either the phone or on the card.
3) What is the procedure to "wipe everything"?
I think the final part I know how to do with ODIN. Just go to download boot and load and run odin with the ROM.
I got the BTU ROM is that not for the UK? I tried looking up what NC2 was but did not really find anything the explained what it is.
Thanks again and sorry for the ignorance on my side.
Let's put the custom recovery and all that on the back burner for now.
Was your phone unlocked from the factory or did you get it from a carrier? If from a carrier, which, and is it unlocked now or you are still using it with the original carrier? This one is for Vodaphone http://www.sammobile.com/firmwares/3/?download=27401 but if you are unlocked, it should work anyway, I believe.
Thanks to the people for their replies. I managed to solve the issue as below.
As mentioned previously I had flashed using ODIN and BTU version of N9005XXUENB7. The only other thing that was then required was to enter the recovery (I think power + volume up + home and then release power once samsung name appears). I then selected wipe data/factory. A reboot later and everything was solved.
es0tericcha0s said:
Sounds like a bit of a pickle. Since you know that Odin is working and the firmware you have at least flashes correctly, I'd consider installing a custom recovery, backing up EFS folder (and the rom too, just in case there is some weird issue with Odin the 2nd time around) , then wipe everything - /system included. This will make your phone not be able to boot up at all because it will wipe the OS off. Then just boot directly to Download and redo the firmware flash. Something else to consider since you do have the international version, is that some of the firmwares you install might be more carrier or region specific, so there might be a better option to install. I know that there is a some slightly newer version that has NC2 in it as I was trying to fix one of these phones the other day that could not register on any network and ran across that build. Do you remember the build number of the software before you started modding?
Click to expand...
Click to collapse
Hi, The other day i tried to fix the Platform.xml. on my S5. i noticed sometime after that when i move files using the "My files" app, the phone would not refresh the files so that they would show up in gallery, videos etc.. I tried to undo the Media_rw by using SD Maid to find the Platform.xml and Axel to rewrite the Xml. In the platform.xml. i deleted the Media_rw and replaced the old xml with the old (original) one. I rebooted my phone. On swiping to open the screen i noticed alot of apps crashing one after the other. I when back to SD Maid and searched for Platform.xml and opened it with Axel but it said file not found.. i can not use the internet, i cant use most apps, i cant even use the Kies on my computer. I cant save anything to the storage either. I really need help. Odin is the only thing i can use. but i dont know how i can reset the xml files on my phone.. What exactly am i do to?
please
christaph3r said:
Hi, The other day i tried to fix the Platform.xml. on my S5. i noticed sometime after that when i move files using the "My files" app, the phone would not refresh the files so that they would show up in gallery, videos etc.. I tried to undo the Media_rw by using SD Maid to find the Platform.xml and Axel to rewrite the Xml. In the platform.xml. i deleted the Media_rw and replaced the old xml with the old (original) one. I rebooted my phone. On swiping to open the screen i noticed alot of apps crashing one after the other. I when back to SD Maid and searched for Platform.xml and opened it with Axel but it said file not found.. i can not use the internet, i cant use most apps, i cant even use the Kies on my computer. I cant save anything to the storage either. I really need help. Odin is the only thing i can use. but i dont know how i can reset the xml files on my phone.. What exactly am i do to?
please
Click to expand...
Click to collapse
Hey, I was wondering if you ever got a fix on this without factory reset. I am having the exact same issue.
Same boat here. Please someone help!
woahs said:
Hey, I was wondering if you ever got a fix on this without factory reset. I am having the exact same issue.
Click to expand...
Click to collapse
I am having exact same problem. After editing the platform.xml, my Note 3 is behaving the same way: no access to any storage area (including USB drive), no remote access/online access (even though WIFI and 4G appear to connect just fine), most apps fail with 'Unfortunately ... has stopped' error message, no Google Play...
I really don't want to do a factory reset, but really, does it even help? Is there a way to put the platform.xml back? Is there a way to access the phone via USB cable?
vbcomer said:
I am having exact same problem. After editing the platform.xml, my Note 3 is behaving the same way: no access to any storage area (including USB drive), no remote access/online access (even though WIFI and 4G appear to connect just fine), most apps fail with 'Unfortunately ... has stopped' error message, no Google Play...
I really don't want to do a factory reset, but really, does it even help? Is there a way to put the platform.xml back? Is there a way to access the phone via USB cable?
Click to expand...
Click to collapse
Update: I went ahead and successfully install the all-in-one file to the phone via Odin, but it still has the same issues. Can someone give a hint? thanks
FIX!!!
Hi I'm a god at searching(hence the Go)but an Noob(hence the obie) to Dev on Android but a computer techy(in other words I fix computers upgrade ETC.) Now if you followed EXACT instructions you SHOULD have the Backup copy of platform.xml. If not reply and I'll give those instructions.
So I did the same as this post did to get my issue as well but there's a SOLUTION I just found W/o getting rid of your loved files and its easy!
1. Download the ADB also included in The Android SDK by Google (approx. 3XX MB)
2. DOWNLOAD Root Explorer.APK
3. Extract ADB Dev kit( name should be roughly adt-bundle-windows-x86_64-20140702.zip)Note: I prefered it at C:\Android it avoided Name too long error
4. Open CMD Type: cd C:\<location ADB was extracted>\sdk\platform-tools(if you followed my note it will be "C:\Android\adt-bundle-windows-x86_64-20140702\sdk\platform-tools") and press enter... HINT TO COPY PASTE IN CMD RIGHT CLICK SAVES TIME!!!!
5. Install Root Explorer so you can backup your files(if any) I was unlucky having none on the phone but SD storage is ok!
To do this type ADB INSTALL <Location of Root explorer.exe> For standard windows users with default download locations it would be "C:\Users\<USER NAME>\Downloads\Root Explorer v3.1.9.apk" <COPY PASTE
6. Copy the original back to System>ETC>Permissions and overwrite
7. Factory reset!
Links?
sorry guys bt i have the same note 3 and i delete the platform.xml file .....i did a factory reset bt nothing happened ...can u help plz
Re:FIX!
But you have to set the permissions of platform.xml as 0777.Right?
Step 5 how should it works
Android Goobie said:
Hi I'm a god at searching(hence the Go)but an Noob(hence the obie) to Dev on Android but a computer techy(in other words I fix computers upgrade ETC.) Now if you followed EXACT instructions you SHOULD have the Backup copy of platform.xml. If not reply and I'll give those instructions.
So I did the same as this post did to get my issue as well but there's a SOLUTION I just found W/o getting rid of your loved files and its easy!
1. Download the ADB also included in The Android SDK by Google (approx. 3XX MB)
2. DOWNLOAD Root Explorer.APK
3. Extract ADB Dev kit( name should be roughly adt-bundle-windows-x86_64-20140702.zip)Note: I prefered it at C:\Android it avoided Name too long error
4. Open CMD Type: cd C:\<location ADB was extracted>\sdk\platform-tools(if you followed my note it will be "C:\Android\adt-bundle-windows-x86_64-20140702\sdk\platform-tools") and press enter... HINT TO COPY PASTE IN CMD RIGHT CLICK SAVES TIME!!!!
5. Install Root Explorer so you can backup your files(if any) I was unlucky having none on the phone but SD storage is ok!
To do this type ADB INSTALL <Location of Root explorer.exe> For standard windows users with default download locations it would be "C:\Users\<USER NAME>\Downloads\Root Explorer v3.1.9.apk" <COPY PASTE
6. Copy the original back to System>ETC>Permissions and overwrite
7. Factory reset!
Links?
Click to expand...
Click to collapse
Hi have next message in the install root step could you help me please
Android Debug Bridge version 1.0.31
-a - directs adb to listen on all interfaces for a connection
-d - directs command to the only connected USB device
returns an error if more than one USB device is present.
-e - directs command to the only running emulator.
returns an error if more than one emulator is r
unning.
-s <specific device> - directs command to the device or emulator with
the given
serial number or qualifier. Overrides ANDROID_SERIAL
environment variable.
-p <product name or path> - simple product name like 'sooner', or
a relative/absolute path to a product
out directory like 'out/target/product/sooner'.
If -p is not specified, the ANDROID_PRODUCT_OUT
environment variable is used, which must
be an absolute path.
-H - Name of adb server host (default: localhost)
-P - Port of adb server (default: 5037)
devices [-l] - list all connected devices
('-l' will also list device qualifiers)
connect <host>[:<port>] - connect to a device via TCP/IP
Port 5555 is used by default if no port number
is specified.
disconnect [<host>[:<port>]] - disconnect from a TCP/IP device.
Port 5555 is used by default if no port number
is specified.
Using this command with no additional arguments
will disconnect from all connected TCP/IP devices.
device commands:
adb push [-p] <local> <remote>
- copy file/dir to device
('-p' to display the transfer progress)
adb pull [-p] [-a] <remote> [<local>]
- copy file/dir from device
('-p' to display the transfer progress)
('-a' means copy timestamp and mode) adb sync [ <directory> ] - copy host->device only if changed
(-l means list but don't copy)
(see 'adb help all')
adb shell - run remote shell interactively
adb shell <command> - run remote shell command
adb emu <command> - run emulator console command
adb logcat [ <filter-spec> ] - View device log
adb forward --list - list all forward socket connections.
the format is a list of lines with the followin
g format:
<serial> " " <local> " " <remote> "\n" adb forward <local> <remote> - forward socket connections
forward specs are one of:
tcp:<port>
localabstract:<unix domain socket name>
localreserved:<unix domain socket name>
localfilesystem:<unix domain socket name>
dev:<character device name>
jdwp:<process pid> (remote only) adb forward --no-rebind <local> <remote>
- same as 'adb forward <local> <remote>' but fails
if <local> is already forwarded
adb forward --remove <local> - remove a specific forward socket connection
adb forward --remove-all - remove all forward socket connections
adb jdwp - list PIDs of processes hosting a JDWP transport
adb install [-l] [-r] [-d] [-s] [--algo <algorithm name> --key <hex-encoded ke
y> --iv <hex-encoded iv>] <file>
- push this package file to the device and install it
('-l' means forward-lock the app)
('-r' means reinstall the app, keeping its data)
('-d' means allow version code downgrade)
('-s' means install on SD card instead of inter
nal storage)
('--algo', '--key', and '--iv' mean the file is
encrypted already)
adb uninstall [-k] <package> - remove this app package from the device
('-k' means keep the data and cache directories)
adb bugreport - return all information from the device
that should be included in a bug report.
adb backup [-f <file>] [-apk|-noapk] [-obb|-noobb] [-shared|-noshared] [-all]
[-system|-nosystem] [<packages...>]
- write an archive of the device's data to <file>
.
If no -f option is supplied then the data is written
to "backup.ab" in the current directory.
(-apk|-noapk enable/disable backup of the .apks themselves
in the archive; the default is noapk.)
(-obb|-noobb enable/disable backup of any installed apk expansion
(aka .obb) files associated with each application; the default is noobb.)
(-shared|-noshared enable/disable backup of the device's
shared storage / SD card contents; the default is noshared.)
(-all means to back up all installed applications)
(-system|-nosystem toggles whether -all automatically includes
system applications; the default is to include system apps)
(<packages...> is the list of applications to be backed up. If
the -all or -shared flags are passed, then the package
list is optional. Applications explicitly given on the
command line will be included even if -nosystem would
ordinarily cause them to be omitted.) adb restore <file> - restore device contents from the <file> backup
archive
adb help - show this help message
adb version - show version num
scripting:
adb wait-for-device - block until device is online
adb start-server - ensure that there is a server running
adb kill-server - kill the server if it is running
adb get-state - prints: offline | bootloader | device
adb get-serialno - prints: <serial-number>
adb get-devpath - prints: <device-path>
adb status-window - continuously print device status for a specifie
d device
adb remount - remounts the /system partition on the device re
ad-write
adb reboot [bootloader|recovery] - reboots the device, optionally into the boo
tloader or recovery program
adb reboot-bootloader - reboots the device into the bootloader
adb root - restarts the adbd daemon with root permissions
adb usb - restarts the adbd daemon listening on USB
adb tcpip <port> - restarts the adbd daemon listening on TCP on the specified port
networking:
adb ppp <tty> [parameters] - Run PPP over USB.
Note: you should not automatically start a PPP connection.
<tty> refers to the tty for PPP stream. Eg. dev:/dev/omap_csmi_tty1 [parameters] - Eg. defaultroute debug dump local notty usepeerdns
adb sync notes: adb sync [ <directory> ]
<localdir> can be interpreted in several ways:
- If <directory> is not specified, both /system and /data partitions will be updated.
- If it is "system" or "data", only the corresponding partition is updated.
environmental variables:
ADB_TRACE - Print debug information. A comma separated list of the following values
1 or all, adb, sockets, packets, rwx, usb, sync, sysdeps, transport, jdwp
ANDROID_SERIAL - The serial number to connect to. -s takes priority over this if given.
ANDROID_LOG_TAGS - When used with the logcat option, only these debug tags are printed.
I'm running debian with linux deploy on a external hd, and android is constantly (seems to be every reboot or usb reconnect) it changes the name of the usb drive by adding/removing a (1). This prevents linux deploy from being able to find its img file and auto-starting, any ideas on how to set a fixed name?
On a sidebar I have a smsc7500 1gb usb net card and it needs a driver installed to work, from terminal (insmod /system/lib/modules/smsc75xx.ko) loads it no problem, but apparently init.rc is running from initrd as a ram disk, so adding the insmod cmd to init.rc is not persistent, I've tried scriptmanager and .sh files (getting a strange "syntax error" unexpected (/4) not sure what's up wit dat) anyone have a simpler way than breaking into initrd and making changes there to auto-load a module?