mi A3 Dead - Xiaomi Mi A3 Questions & Answers

When i flashed the Evolution X Rom to Stock rom It Got Failed And My Device Is Not Turning ON.
Whenever I Tried To Install stock Rom using mi flash tool It Is Saying "Cannot Recieve Hello Packet" & write time out,maybe device was disconnected Please Help ME To Fix

The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.

papsr6 said:
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
Click to expand...
Click to collapse
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...

wetito said:
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
Click to expand...
Click to collapse
I Had Tried EDL flashing from Unlock Tool Flashing Done Perfectly But Formatting Failed..Is it a partition error ?.. The Display is not turning on.. No Signal Only The Signal is Entering EDL mode

wetito said:
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
Click to expand...
Click to collapse
papsr6 said:
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
Click to expand...
Click to collapse
My Phone Is Now Like This :

hishamhsm said:
I Had Tried EDL flashing from Unlock Tool Flashing Done Perfectly But Formatting Failed..Is it a partition error ?.. The Display is not turning on.. No Signal Only The Signal is Entering EDL mode
Click to expand...
Click to collapse
What you wrote is not good... I don't know unloock tool. But before use this applications is necessary read carefully the instructions. It seems you didn't have do this. Good luck. Ps: if your phone boot into fastboot reflash stock via miflash... If you don't have made a big damage it will work. Very import is select the correct slot before flash... In my case i always select slot a to make a clean and safe installation

wetito said:
What you wrote is not good... I don't know unloock tool. But before use this applications is necessary read carefully the instructions. It seems you didn't have do this. Good luck. Ps: if your phone boot into fastboot reflash stock via miflash... If you don't have made a big damage it will work. Very import is select the correct slot before flash... In my case i always select slot a to make a clean and safe installation
Click to expand...
Click to collapse
is mi authorized account needed

hishamhsm said:
is mi authorized account needed
Click to expand...
Click to collapse
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary

wetito said:
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
Click to expand...
Click to collapse
no fastboot , no charging

wetito said:
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
Click to expand...
Click to collapse
will you help me to flash my phone via teamviewer

Sorry if you have damage bootloader (so fastboot don't work), the only way is edl. But i don't know how to solve edl flash fail. You had ask to other user, or search with Google. Or i'm afraid for you... Buy new phone. For the future if you want modding... Do it carefully

wetito said:
Sorry if you have damage bootloader (so fastboot don't work), the only way is edl. But i don't know how to solve edl flash fail. You had ask to other user, or search with Google. Or i'm afraid for you... Buy new phone. For the future if you want modding... Do it carefully
Click to expand...
Click to collapse
Thanks Bro Thanks For Your Support,.... Love From Kerala , India

Good luck

Same thing happened to me then i went mi authorised service centre and they charged 179rs and now my phone is working fine

azeem_saifi0411 said:
Same thing happened to me then i went mi authorised service centre and they charged 179rs and now my phone is working fine
Click to expand...
Click to collapse
is that phone under warranty while it was bricked

hishamhsm said:
is that phone under warranty while it was bricked
Click to expand...
Click to collapse
Sorry no. You have the bootloader unlocked... If your restore via edl will fail, in my opinion the best choice is buy a new phone. I don't know in your country. considerating that motheborard is not damaged... But phone must be open... The minum cost of this repair i think could be 100 € (convert in your currency). On YouTube there are a lot of tutorial how to do by yourself... But i'm not shure you have all skills...

wetito said:
Sorry no. You have the bootloader unlocked... If your restore via edl will fail, in my opinion the best choice is buy a new phone. I don't know in your country. considerating that motheborard is not damaged... But phone must be open... The minum cost of this repair i think could be 100 € (convert in your currency). On YouTube there are a lot of tutorial how to do by yourself... But i'm not shure you have all skills...
Click to expand...
Click to collapse
I Have Given It to A repair shop. They told me that that is emmc/UFS chip issue. So they will reprogramme the chip fix it and give the phone to me... They Told that it should fix..
Anyway I'm from India

hishamhsm said:
I Have Given It to A repair shop. They told me that that is emmc/UFS chip issue. So they will reprogramme the chip fix it and give the phone to me... They Told that it should fix..
Anyway I'm from India
Click to expand...
Click to collapse
I suppose that was the problem. I hope the repair shop in india are cheapest than in italy for the future... Make Modding with care

wetito said:
I suppose that was the problem. I hope the repair shop in india are cheapest than in italy for the future... Make Modding with care
Click to expand...
Click to collapse
Repairing cost around 10dollars . In India repairing cost is low but the price of mobile phones and spare parts are too high due to tax.

Thank you so much for your help and support bro. Love From India❤❤

Related

how can i get my phone working!? #PLZANSWR

hi
before everything, i should say that my English is poor!
my friend has a RN3 Pro, and he forgot his password. so, the phone is locked now. the bootloader is locked, and the phone is not verified in any account (Gmail, MI,etc.) what is the solution now!? how can i get the phone working?
my only hope is your solutions...
I guess you could try the mi flash tool with the flash all option, or edl mode -
I doubt there is a way to recover data at this point unless he had a custom recovery.
otyg said:
I guess you could try the mi flash tool with the flash all option, or edl mode -
I doubt there is a way to recover data at this point unless he had a custom recovery.
Click to expand...
Click to collapse
the data in not important anymore, i just want to get the phone working back (with or without data)
can you tell me more about edl mode? can it remove the password?! i ask because it seems that in this situation u cant do all flash methods (cant do anything even with mi flash)
I used this guide when I first 'bricked' my Note3. You really need to learn to use MiFlash, it will save your life!
http://en.miui.com/thread-235865-1-1.html
7 Ways to Bypass Android's Secured Lock Screen
Method 5 or 7 in the above link might work for you.
Intosia said:
I used this guide when I first 'bricked' my Note3. You really need to learn to use MiFlash, it will save your life!
http://en.miui.com/thread-235865-1-1.html
Click to expand...
Click to collapse
as i said before, the phone is locked and the Android Debugging is off. so all ADB methods should not work...
i'm going to try EDL Mode method...

Bricked my note 4 while unlocking... Please Help

Hello, i got a big problem and needed HELP!
Today i got my Note 4...
so i tryed to unlock the bootloader, bad thing did not logg in at the device.
i booted the mobile in fastboot mode and started the official unlock tool.
until 50% it went quite well then i got an error message:
couldn't verify device
current account is differnet from the account info on the device
so i tryed to boot again but was in a bootloop...
i tryed also flashing a new rom (nikel_global_images_7.4.14_20170414.0000.00_6.0_global_b5d5f15e0e.tgz) and again i got an error
"flash boot error"
hope somebody can help
p.s. sorry for my poor english
Following
Did you read this?
dao80 said:
...i tryed also flashing a new rom (nikel_global_images_7.4.14_20170414.0000.00_6.0_global_b5d5f15e0e.tgz) and again i got an error...
Click to expand...
Click to collapse
Are you sure you are using MTK Variant?
akil777 said:
Did you read this?
Are you sure you are using MTK Variant?
Click to expand...
Click to collapse
yes im sure, i tryed this already and still in bootloop
althoug it says download ok
dao80 said:
yes im sure, i tryed this already and still in bootloop
althoug it says download ok
Click to expand...
Click to collapse
Did you use Sp flash tool?, if yes You should tick all except preloader. You will have to wait 5-15mins for the phone to boot up.
akil777 said:
Did you use Sp flash tool?, if yes You should tick all except preloader. You will have to wait 5-15mins for the phone to boot up.
Click to expand...
Click to collapse
yes i used this tool, after rebooting the mi logo is on the screnn for about 7 secounds then the mobile boots again and again...
;(
dao80 said:
yes i used this tool, after rebooting the mi logo is on the screnn for about 7 secounds then the mobile boots again and again...
;(
Click to expand...
Click to collapse
I have never experienced that.. I think you should send it to your mobile repair center.. Be patient,, It might take few days. Don't panic,
akil777 said:
I have never experienced that.. I think you should send it to your mobile repair center.. Be patient,, It might take few days. Don't panic,
Click to expand...
Click to collapse
i m already looking for a mobile repair center here who can repair xiaomi mobiles...
but so fare all numbers i called are not in service anymore or dont repair xiaomi...
dao80 said:
i m already looking for a mobile repair center here who can repair xiaomi mobiles...
but so fare all numbers i called are not in service anymore or dont repair xiaomi...
Click to expand...
Click to collapse
check this http://en.miui.com/thread-491655-1-1.html
You tried putting phone in fast boot mode (volume down then power). Then just flash the stock firmware?
robjbw said:
You tried putting phone in fast boot mode (volume down then power). Then just flash the stock firmware?
Click to expand...
Click to collapse
yes i tried china and global
but only bootloop
but to be on the save side, where to i find a the stock rom (flashable with the miflashtool)?
dao80 said:
yes i tried china and global
but only bootloop
but to be on the save side, where to i find a the stock rom (flashable with the miflashtool)?
Click to expand...
Click to collapse
flash done with mi flash? If got error then try with deep flash cable. see yt tutorials
itsmedRb said:
flash done with mi flash? If got error then try with deep flash cable. see yt tutorials
Click to expand...
Click to collapse
deepflash is also possible for mtk devices?
robjbw said:
You tried putting phone in fast boot mode (volume down then power). Then just flash the stock firmware?
Click to expand...
Click to collapse
tried it again with the mi flash tool i got following error
80x80004005: FAILED (remote: download for partition 'boot' is not allowed
Hey Guys, i soveld the problem...
AND F**K it was a quite easy solution...
i tried so hard was crying and a kind of very desperate...
anyways i aslo wrot a mail to mi and they did not help at all...
they even say i should lock in at the device if im in a bootloop, kinda funny?
anyways so i drained the batterie and nearly about to give up this device....
BUT i give it one last try, plugt it in and booted it... it took a while but after a while i finaly was able to boot the Phone and set it up...
so this threat can be closed...
thank you guys for your help

PLEASE HELP!! Bootloop exist even after flashing with EDL test point method

So my phone just got stuck while normal usage. Tried restarting and the phone began boot looping.
Did plenty of research and finally decided to flash. Tried to flash using mi flash in fastboot mode but failed then google search made me realise my bootloader was locked. Did more research and decided to flash using test point EDL method.
Things went pretty well and the flash (miui v8) and the process became successful and when I powered my device the phone went back to boot loop again.
Tried flashing again and the result was the same.
It would be really helpful if somebody could actually help clear the issue. Did pretty much everything I could do as a newbie to flashing.
thank you!
There are 2 varients of rn4 one is mediatek(note 4x) and the other is Snapdragon so check if u flashed right firmware
thisbearisdrunk said:
There are 2 varients of rn4 one is mediatek(note 4x) and the other is Snapdragon so check if u flashed right firmware
Click to expand...
Click to collapse
No, I have flashed the correct file(Mido) and the flashing process went quite well but the problem still exists.
M i L i N said:
No, I have flashed the correct file(Mido) and the flashing process went quite well but the problem still exists.
Click to expand...
Click to collapse
How is ur phone being recognised in mi flash tool?
A serial number appears or something else like "com_port" appears?
thisbearisdrunk said:
How is ur phone being recognised in mi flash tool?
A serial number appears or something else like "com_port" appears?
Click to expand...
Click to collapse
It's recognised as COM4 the first time I tried then sometimes when I connect it shows COM3.
M i L i N said:
It's recognised as COM4 the first time I tried then sometimes when I connect it shows COM3.
Click to expand...
Click to collapse
If it recognises ur phone like that then flashing does nothing to ur phone so the only way is to go into edl mode and then flashing
https://forum.xda-developers.com/re...ool-redmi-note-4-edl-mode-o-removing-t3684024
Use this tool to go into edl mode and then flash
This thread can help ,because i bricked my phone once without unlocking the bootloader and the miflashtool recognised my phone like how it recognised urs and this thread saved my phone
Good luck

P20 lite (ANE-LX1) bootloop/stuck can't go recovery questions for boot unlock service

Hi everyone and sorry for my bad english i'm Italian i have a big problem with a P20 lite that won't boot up. When i power on the device he got stuck on brand screen (TIM branded) and if i try to shut it down the phone starts a rebooting in the same screen and got stuck in TIM screen another time. I tryed to enter in recovery in many ways, even with USB and ADB, but the only response i have is with buttons and is a totally green screen with a blue square in top and red one in bottom of the screen with this green background, i can only go in Huawei download mode and use ADB tools, i can't even use the official HiSuite application like the Huawei download mode suggest me because i can't activate developers options. The good fact and the only road to work i guess is that i can use the ADB tools but even if i try to enter in recovery typing "fastboot reboot recovery" the board give me "not allowed" if i try to reflesh system or any stock img he don't allow me to do anything except mormal reboot and device COM address with the check devices command. The bootloader is clearily locked and with some research i found that the only way to unlock the bootloader on this devices is trust to unlocking services with credits like "DC Phoneix, Chimera etc." but my doubt now is.. if i'm ain't able to power on and go in menu and information of the phone to get needed infos like serial and others and sharing this with services to let the procedure work, how i can do? OR the services like this is total automatic i only got to pay and go even with a total unaccessible phone? I have Chimera and i achieved to extract the stock img and UPDATE.APP to this phone but i'm unable (like i say) to flashing everything i can do anything else with Chimera? Or anything else with other methods? I also buyed the MTK dongle i wish to try it. The phone is totally stock not rooted, never unlocked. Sorry for my bad english the last time and thanks for reading. If some point or question it's not clear i'm here to explain better my doubt.
Androny4andro said:
i can only go in Huawei download mode .
Click to expand...
Click to collapse
Hi, what do you mean by that? E-Recovery ?
Ane how it got bricked?
-Alf- said:
Hi, what do you mean by that? E-Recovery ?
Click to expand...
Click to collapse
No 0 Recovery only download/fastboot mode
Androny4andro said:
No 0 Recovery only download/fastboot mode
Click to expand...
Click to collapse
Okay, but what is "download mode"?
And how it got bricked? It's very important!
-Alf- said:
Okay, but what is "download mode"?
And how it got bricked? It's very important!
Click to expand...
Click to collapse
There's no special event to the brick, is bricked by itself, i post a link that can explain the mode, it's not mine of course i got in web but it's the same screen of mine
https://obrazki.elektroda.pl/3270005500_1518165931_thumb.jpg
Androny4andro said:
There's no special event to the brick, is bricked by itself, i post a link that can explain the mode, it's not mine of course i got in web but it's the same screen of mine
https://obrazki.elektroda.pl/3270005500_1518165931_thumb.jpg
Click to expand...
Click to collapse
It isn't download mode, simply fastboot mode. Bricked by itself? Bro, I also had this problem with the green screen, it happened after rebranding, after flashing wrong oeminfo and wrong FW .* But with the unlocked BL it was not a problem. Okay, it doesn't matter...
In fastboot mode run this command:
fastboot oem get-build-number
tell me result, please.
-Alf- said:
It isn't download mode, simply fastboot mode. Bricked by itself? Bro, I also had this problem with the green screen, it happened after rebranding, after flashing wrong oeminfo and wrong FW .* But with the unlocked BL it was not a problem. Okay, it doesn't matter...
In fastboot mode run this command:
fastboot oem get-build-number
tell me result, please.
Click to expand...
Click to collapse
I'm pretty sure that i don't have doing nothing about this or other to have this disastrous result.. anyway the result of command is that:
(bootloader) :ANE-LX1 9.1.0.306(C55E7R1P6)
OKAY [ 0.020s]
finished. total time: 0.021s
Androny4andro said:
I'm pretty sure that i don't have doing nothing about this or other to have this disastrous result.. anyway the result of command is that:
(bootloader) :ANE-LX1 9.1.0.306(C55E7R1P6)
OKAY [ 0.020s]
finished. total time: 0.021s
Click to expand...
Click to collapse
Okay, I believe You but it's strange...
Thanks, wait a moment please, I sent your data to an expert.
-Alf- said:
Okay, I believe You but it's strange...
Thanks, wait a moment, I sent your data to an expert.
Click to expand...
Click to collapse
it's my friend's smartphone actually the sister's smartphone, they don't understand nothing and are not interested about modding or things like that they are the kind of people that use the phone only for normal use. That's because i'm pretty sure this telephone is not touched for "strange" modding, rooting, etc. I don't known if my friend sis' have a geek/Android nerd friend or boyfriend at college but i don't think, i don't known and have no interest to known that :laugh: anyway thanks for help i'm waiting you
Androny4andro said:
it's my friend's smartphone actually the sister's smartphone, they don't understand nothing and are not interested about modding or things like that they are the kind of people that use the phone only for normal use. That's because i'm pretty sure this telephone is not touched for "strange" modding, rooting, etc. I don't known if my friend sis' have a geek/Android nerd friend or boyfriend at college but i don't think, i don't known and have no interest to known that :laugh: anyway thanks for help i'm waiting you
Click to expand...
Click to collapse
So, it's possible unbrick this phone online with TeamViewer on PC using paid service ministryofsolution.com .
And need to open back cover of your phone (due to a test-point method). IMO the best solution. Or you can try DC-Phoenix for 19euros, but you have to do everything manually, without experience it's a risk...
https://mega.nz/file/nkZTAYJJ#VtavigGBgDkgJAJk6a5M-3DsUfX4bMjJ_gKjbqA2wpI <------ no lose oem and imei board !
download image download tool 2.0.0.9
charged batery
1. dissasembly the phone.
2. short test point (find on www) install drivers if need
3. open Image download tool
4. select xml from link pres play button wait till finish.
5. re update by stock match to ur phone.
If u have error when write sec uce boot its mean board isnt suitable!
rest errors post here

Help! Realme 7 red state Problem

Hi fellow developers.
So,my story is quite weird and expected indeed.
Being the noob I am at flashing custom roms and recoveries,I flashed orange fox recovery on my device,even flashed a custom rom and managed to use it for about 3/4 hours.
Then I thought that my device was ready, all my changes work,and it is a good idea to relock my bootloader.So,without flashing the stock recovery back,I relocked my bootloader.
After reboot,my device is stuck on "Red state" and keeps on rebooting after every 5 secs. I can't even boot to fastboot mode,nor can I completely shut down my device.
So any ideas what can I do? Do I need to go to the service center? If yes,what would they do and how much would they charge?
Thank you!.
Kaybee2611 said:
Hi fellow developers.
So,my story is quite weird and expected indeed.
Being the noob I am at flashing custom roms and recoveries,I flashed orange fox recovery on my device,even flashed a custom rom and managed to use it for about 3/4 hours.
Then I thought that my device was ready, all my changes work,and it is a good idea to relock my bootloader.So,without flashing the stock recovery back,I relocked my bootloader.
After reboot,my device is stuck on "Red state" and keeps on rebooting after every 5 secs. I can't even boot to fastboot mode,nor can I completely shut down my device.
So any ideas what can I do? Do I need to go to the service center? If yes,what would they do and how much would they charge?
Thank you!.
Click to expand...
Click to collapse
Not that only you should have the stock recovery to relock bootloader, you should need to return completely to stock to can relock it safely.
Follow this guide carefully https://forum.xda-developers.com/t/repair-dead-hard-bricked-realme-3-3i-tutorial.4224255/ replace all the files needed when it comes to your specific model.
Kaybee2611 said:
Hi fellow developers.
So,my story is quite weird and expected indeed.
Being the noob I am at flashing custom roms and recoveries,I flashed orange fox recovery on my device,even flashed a custom rom and managed to use it for about 3/4 hours.
Then I thought that my device was ready, all my changes work,and it is a good idea to relock my bootloader.So,without flashing the stock recovery back,I relocked my bootloader.
After reboot,my device is stuck on "Red state" and keeps on rebooting after every 5 secs. I can't even boot to fastboot mode,nor can I completely shut down my device.
So any ideas what can I do? Do I need to go to the service center? If yes,what would they do and how much would they charge?
Thank you!.
Click to expand...
Click to collapse
For future reference, NEVER re-lock the bootloader when your phone isn't 100% stock. The guide SubwayChamp linked above should work.
SubwayChamp said:
Not that only you should have the stock recovery to relock bootloader, you should need to return completely to stock to can relock it safely.
Follow this guide carefully https://forum.xda-developers.com/t/repair-dead-hard-bricked-realme-3-3i-tutorial.4224255/ replace all the files needed when it comes to your specific model.
Click to expand...
Click to collapse
Hey @SubwayChamp
I did try the method you recommended. But,my phone is not recognised as a mediatek device.They show all the connected devices as usb.
Kaybee2611 said:
Hey @SubwayChamp
I did try the method you recommended. But,my phone is not recognised as a mediatek device.They show all the connected devices as usb.
Click to expand...
Click to collapse
[GUIDE] REALME 7 RMX2155 GLOBAL BOOTLOADER UNLOCK
WELCOME, ALL. After a very tiring process of swapping between ROMs and changing regions, APKs, et cetera, we have finally been able to perfect the method for unlocking the bootloader of the RMX2155! This is a detailed guide aimed to give you an...
forum.xda-developers.com
Try following step one to eight inclusive. Should then recognize your device.
Kaybee2611 said:
Hey @SubwayChamp
I did try the method you recommended. But,my phone is not recognised as a mediatek device.They show all the connected devices as usb.
Click to expand...
Click to collapse
how much will service center charge for repairing it??
Hey for me same problem now in my narzo 30a.... can u fix that problem ? @Kaybee2611
daitama said:
how much will service center charge for repairing it??
Click to expand...
Click to collapse
I didn't bring it to the repair center, in my country no one knows about. IDK which the price could be, maybe 40 buckets.

Categories

Resources