Hello,
My realme x3 superzoom is fully bricked.
I got some luck, it is detected as qualcomm 9008
So basicall,if someone have the .mbn file and all the RAW Program and Patch files in .XML, it could greatly help me..
Anyway thanks for your help or even an advice.
Hello,
A little update.
Rn i can go in fastboot but still not in recovery
Im stuck pls help
Hello everyone,
Big update,
I finally made it...
Disclaimer :
I'm not responsible of anything happening to your phone, you are taking those steps at your own risk ...
So if like me you were having a hardbricked phone, follow those steps ( /!\ only if not possible to go to fastboot or bootloader mode, if possible go to next steps) :
- Install QFil ( search for tutorial to know how to set it up good)
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract the ofp file ( need the installation of ofp extractor and python 3)
- Put the phone in EDL mode ( if i remember correctly, you need to press all three button for like more than 20 sec)
- You will need qualcomm driver since your phone will be detected as a com port (Qualcomm HS-USB QDLoader 9008).
- Once you did all those steps, start qfil ( do the firehose config before => select ufs in storage type ), select the
prog_firehose_ddr.elf of YOUR DEVICE in the build selection, then select the rawprogram.xml and the patch.xml
(there should be 5 file for each, select them all)
- Once you did this reboot your phone in EDL mode and as soon as you saw the port is dectected, select download.
- If u get a firehose error => not the good files
- If u get a sahara error then do all of this again but make sur to reboot your phone in EDL mode two
seconds before downloading in QFIL
- If it works => your phone is supposed to boot
If like me for an unknow reason it doesnt work then next steps (FASTBOOT).
For some reason it didnt work fully but it restored fastboot ( got some luck i guess)
So i was able to boot my phone in fastboot/bootloader mode
Once you are in fastboot mode :
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract it with the same method as described earlier.
- You should see a lot of .img, dont worry
- You will need vbmeta.img, recovery.img, boot.img, dtbo.img AND ALL THE super****.img
- Once you find those files, copy past them to a clean folder in order to not mess up.
- On the firmware i found, its a total of 14 super***.img and vbmeta.img, recovery.img, boot.img and dtbo.img.
- Once its in a clean folder, start a cmd and go to this folder ( cd diskname:\..\foldername )
For myself, i flashed the super file in the "order it was given" in the ProFile.xml
- Then you will have to flash all those files
- To flash the super : fastboot flash super super**.img
- To flash the recovery : fastboot flash recovery recovery.img
- To flash the boot : fastboot flash boot boot.img
- To flash dtbo : fastboot flash dtbo dtbo.img
- To flash vbmeta : fastboot flash vbmeta vbmeta.img
Once you are finished flashing those files, your phone should be able to boot ( first go to recovery and wipe
all data in order to not have broken/corrupted files ).
If you have any question, feel free to ask ^^
Please make a video...it has too many complicated step...
Mrinal Mondal said:
Please make a video...it has too many complicated step...
Click to expand...
Click to collapse
Will maybe do it in august if I have time
Plahad said:
Hello everyone,
Big update,
I finally made it...
Disclaimer :
I'm not responsible of anything happening to your phone, you are taking those steps at your own risk ...
So if like me you were having a hardbricked phone, follow those steps ( /!\ only if not possible to go to fastboot or bootloader mode, if possible go to next steps) :
- Install QFil ( search for tutorial to know how to set it up good)
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract the ofp file ( need the installation of ofp extractor and python 3)
- Put the phone in EDL mode ( if i remember correctly, you need to press all three button for like more than 20 sec)
- You will need qualcomm driver since your phone will be detected as a com port (Qualcomm HS-USB QDLoader 9008).
- Once you did all those steps, start qfil ( do the firehose config before => select ufs in storage type ), select the
prog_firehose_ddr.elf of YOUR DEVICE in the build selection, then select the rawprogram.xml and the patch.xml
(there should be 5 file for each, select them all)
- Once you did this reboot your phone in EDL mode and as soon as you saw the port is dectected, select download.
- If u get a firehose error => not the good files
- If u get a sahara error then do all of this again but make sur to reboot your phone in EDL mode two
seconds before downloading in QFIL
- If it works => your phone is supposed to boot
If like me for an unknow reason it doesnt work then next steps (FASTBOOT).
For some reason it didnt work fully but it restored fastboot ( got some luck i guess)
So i was able to boot my phone in fastboot/bootloader mode
Once you are in fastboot mode :
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract it with the same method as described earlier.
- You should see a lot of .img, dont worry
- You will need vbmeta.img, recovery.img, boot.img, dtbo.img AND ALL THE super****.img
- Once you find those files, copy past them to a clean folder in order to not mess up.
- On the firmware i found, its a total of 14 super***.img and vbmeta.img, recovery.img, boot.img and dtbo.img.
- Once its in a clean folder, start a cmd and go to this folder ( cd diskname:\..\foldername )
For myself, i flashed the super file in the "order it was given" in the ProFile.xml
- Then you will have to flash all those files
- To flash the super : fastboot flash super super**.img
- To flash the recovery : fastboot flash recovery recovery.img
- To flash the boot : fastboot flash boot boot.img
- To flash dtbo : fastboot flash dtbo dtbo.img
- To flash vbmeta : fastboot flash vbmeta vbmeta.img
Once you are finished flashing those files, your phone should be able to boot ( first go to recovery and wipe
all data in order to not have broken/corrupted files ).
If you have any question, feel free to ask ^^
Click to expand...
Click to collapse
Good evening!
I've got my device bricked and i follow your guide hoping to fix it, on qfil i got errors so I try with the fastboot method, but after installing all the .img i still can't boot the phone,
Something changed anyway, before I was only able to enter the fastboot mode, now after this if I turn on the phone normally it remains stuck on the first "realme" logo, and pressing - or + can I access fastboot mode or recovery, so things are getting better but still no boot on system, before follow your guide I wasn't even able to format or flash the partition system because it was telling me it wasn't existing, now it exists, but if I try to flash a stock firmware trough fastboot it telling me that there's not enough space on device... I'm a bit stuck too! What can I try?
Bob45ultras said:
Good evening!
I've got my device bricked and i follow your guide hoping to fix it, on qfil i got errors so I try with the fastboot method, but after installing all the .img i still can't boot the phone,
Something changed anyway, before I was only able to enter the fastboot mode, now after this if I turn on the phone normally it remains stuck on the first "realme" logo, and pressing - or + can I access fastboot mode or recovery, so things are getting better but still no boot on system, before follow your guide I wasn't even able to format or flash the partition system because it was telling me it wasn't existing, now it exists, but if I try to flash a stock firmware trough fastboot it telling me that there's not enough space on device... I'm a bit stuck too! What can I try?
Click to expand...
Click to collapse
Hello,
It seems that the storage partition is corrupted
If u can access recovery, try to format the phone and then try again the steps
If u still have no luck with this, reply and I'll try to help u more
Best
Plahad said:
Hello,
It seems that the storage partition is corrupted
If u can access recovery, try to format the phone and then try again the steps
If u still have no luck with this, reply and I'll try to help u more
Plahad said:
Hello,
It seems that the storage partition is corrupted
If u can access recovery, try to format the phone and then try again the steps
If u still have no luck with this, reply and I'll try to help u more
Best
Click to expand...
Click to collapse
Thanks for your reply! I format from the recovery and I repeated the steps but same problem!
Click to expand...
Click to collapse
Plahad said:
Hello,
It seems that the storage partition is corrupted
If u can access recovery, try to format the phone and then try again the steps
If u still have no luck with this, reply and I'll try to help u more
Best
Click to expand...
Click to collapse
Thanks for your reply! I format from recovery and I repeated the steps but same problem!
Bob45ultras said:
Thanks for your reply! I format from recovery and I repeated the steps but same problem!
Click to expand...
Click to collapse
Be very carefull with those next command, it will wipe out completely your devices :
fastboot erase system
fastboot erase userdata
fastboot erase boot
fastboot erase cache
Plahad said:
Be very carefull with those next command, it will wipe out completely your devices :
fastboot erase system
fastboot erase userdata
fastboot erase boot
fastboot erase cache
Click to expand...
Click to collapse
I tried to do that, but it gave me an error when I was trying to erase system and cache, anyway I access fastbootd and I format from them successfully, anyway normal fastboot still can't format system partition.
After that I tried again your guide trough fastboot, re-flashed all files and it still doesn't work,
don't really know what to do, I found a stock firmware flashable trough fastboot and I tried also with that to see if it can solve the problems, but also that it fail, when I try to flash system I receive an error
Bob45ultras said:
I tried to do that, but it gave me an error when I was trying to erase system and cache, anyway I access fastbootd and I format from them successfully, anyway normal fastboot still can't format system partition.
After that I tried again your guide trough fastboot, re-flashed all files and it still doesn't work,
don't really know what to do, I found a stock firmware flashable trough fastboot and I tried also with that to see if it can solve the problems, but also that it fail, when I try to flash system I receive an error
Click to expand...
Click to collapse
Hello,
You can try to install a custom recovery like ofox
Were you on android 10 or 11 ?
Plahad said:
Hello,
You can try to install a custom recovery like ofox
Were you on
Click to expand...
Click to collapse
I'm on Android 11
I followed your steps with the fastboot way but now my phone can't enter both fastboot and recovery,is there anything i can still do?
Or I should just take it to somewhere to repair?
Plahad said:
Hello everyone,
Big update,
I finally made it...
Disclaimer :
I'm not responsible of anything happening to your phone, you are taking those steps at your own risk ...
So if like me you were having a hardbricked phone, follow those steps ( /!\ only if not possible to go to fastboot or bootloader mode, if possible go to next steps) :
- Install QFil ( search for tutorial to know how to set it up good)
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract the ofp file ( need the installation of ofp extractor and python 3)
- Put the phone in EDL mode ( if i remember correctly, you need to press all three button for like more than 20 sec)
- You will need qualcomm driver since your phone will be detected as a com port (Qualcomm HS-USB QDLoader 9008).
- Once you did all those steps, start qfil ( do the firehose config before => select ufs in storage type ), select the
prog_firehose_ddr.elf of YOUR DEVICE in the build selection, then select the rawprogram.xml and the patch.xml
(there should be 5 file for each, select them all)
- Once you did this reboot your phone in EDL mode and as soon as you saw the port is dectected, select download.
- If u get a firehose error => not the good files
- If u get a sahara error then do all of this again but make sur to reboot your phone in EDL mode two
seconds before downloading in QFIL
- If it works => your phone is supposed to boot
If like me for an unknow reason it doesnt work then next steps (FASTBOOT).
For some reason it didnt work fully but it restored fastboot ( got some luck i guess)
So i was able to boot my phone in fastboot/bootloader mode
Once you are in fastboot mode :
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract it with the same method as described earlier.
- You should see a lot of .img, dont worry
- You will need vbmeta.img, recovery.img, boot.img, dtbo.img AND ALL THE super****.img
- Once you find those files, copy past them to a clean folder in order to not mess up.
- On the firmware i found, its a total of 14 super***.img and vbmeta.img, recovery.img, boot.img and dtbo.img.
- Once its in a clean folder, start a cmd and go to this folder ( cd diskname:\..\foldername )
For myself, i flashed the super file in the "order it was given" in the ProFile.xml
- Then you will have to flash all those files
- To flash the super : fastboot flash super super**.img
- To flash the recovery : fastboot flash recovery recovery.img
- To flash the boot : fastboot flash boot boot.img
- To flash dtbo : fastboot flash dtbo dtbo.img
- To flash vbmeta : fastboot flash vbmeta vbmeta.img
Once you are finished flashing those files, your phone should be able to boot ( first go to recovery and wipe
all data in order to not have broken/corrupted files ).
If you have any question, feel free to ask ^^
Click to expand...
Click to collapse
my phone just open bootloader and apply the second step but no thing repair, my phone is RMX2086 any one can help me please
Do you have the Firehose , rawprogram and patch files that you can post to try to do it by qfil ?
Plahad said:
Hello everyone,
Big update,
I finally made it...
Disclaimer :
I'm not responsible of anything happening to your phone, you are taking those steps at your own risk ...
So if like me you were having a hardbricked phone, follow those steps ( /!\ only if not possible to go to fastboot or bootloader mode, if possible go to next steps) :
- Install QFil ( search for tutorial to know how to set it up good)
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract the ofp file ( need the installation of ofp extractor and python 3)
- Put the phone in EDL mode ( if i remember correctly, you need to press all three button for like more than 20 sec)
- You will need qualcomm driver since your phone will be detected as a com port (Qualcomm HS-USB QDLoader 9008).
- Once you did all those steps, start qfil ( do the firehose config before => select ufs in storage type ), select the
prog_firehose_ddr.elf of YOUR DEVICE in the build selection, then select the rawprogram.xml and the patch.xml
(there should be 5 file for each, select them all)
- Once you did this reboot your phone in EDL mode and as soon as you saw the port is dectected, select download.
- If u get a firehose error => not the good files
- If u get a sahara error then do all of this again but make sur to reboot your phone in EDL mode two
seconds before downloading in QFIL
- If it works => your phone is supposed to boot
If like me for an unknow reason it doesnt work then next steps (FASTBOOT).
For some reason it didnt work fully but it restored fastboot ( got some luck i guess)
So i was able to boot my phone in fastboot/bootloader mode
Once you are in fastboot mode :
- Download the original firmware file ( /!\ NOT THE OZIP BUT THE OFP)
- Extract it with the same method as described earlier.
- You should see a lot of .img, dont worry
- You will need vbmeta.img, recovery.img, boot.img, dtbo.img AND ALL THE super****.img
- Once you find those files, copy past them to a clean folder in order to not mess up.
- On the firmware i found, its a total of 14 super***.img and vbmeta.img, recovery.img, boot.img and dtbo.img.
- Once its in a clean folder, start a cmd and go to this folder ( cd diskname:\..\foldername )
For myself, i flashed the super file in the "order it was given" in the ProFile.xml
- Then you will have to flash all those files
- To flash the super : fastboot flash super super**.img
- To flash the recovery : fastboot flash recovery recovery.img
- To flash the boot : fastboot flash boot boot.img
- To flash dtbo : fastboot flash dtbo dtbo.img
- To flash vbmeta : fastboot flash vbmeta vbmeta.img
Once you are finished flashing those files, your phone should be able to boot ( first go to recovery and wipe
all data in order to not have broken/corrupted files ).
If you have any question, feel free to ask ^^
Click to expand...
Click to collapse
Does your guide only apply to Realme with unlocked Bootloader or to all?
Ian94y said:
I followed your steps with the fastboot way but now my phone can't enter both fastboot and recovery,is there anything i can still do?
Or I should just take it to somewhere to repair?
Click to expand...
Click to collapse
If u cant enter fastboot, i'll suggest that u either find a way arounds with QFIL or else if not comfortable go to repair it somewhere
aliabdullah1230 said:
my phone just open bootloader and apply the second step but no thing repair, my phone is RMX2086 any one can help me please
Click to expand...
Click to collapse
Hello, did u download the good firmwares for your phone ?
I have an rmx2086 too, and i managed to made it work by doing what i did with those commends
felixpaz1992 said:
Do you have the Firehose , rawprogram and patch files that you can post to try to do it by qfil ?
Click to expand...
Click to collapse
I'm sorry, I'm not currently in my home, i'll try do find those when i'll get back, in 4 months
Related
Hi guys
I tried to go back to stock android 5.0.1 from a custom rom based on marshmallow. I did everything you told me to do in other thread but still I failed :crying: :crying: :crying: :crying: and got into Bootloop. Nothing I can do with my phone except going into Fastboot&Rescuemode. HiSuite does not see my phone (i think its the custom rom bug). Please help me ;c
Tried things mentioned in this thread http://forum.xda-developers.com/honor-7/general/guide-beginners-how-to-root-update-fix-t3255452 ,still in bootloop
fixed!
I had to flash Android 6 recovery etc.
Szumy said:
Hi guys
I tried to go back to stock android 5.0.1 from a custom rom based on marshmallow. I did everything you told me to do in other thread but still I failed :crying: :crying: :crying: :crying: and got into Bootloop. Nothing I can do with my phone except going into Fastboot&Rescuemode. HiSuite does not see my phone (i think its the custom rom bug). Please help me ;c
Tried things mentioned in this thread http://forum.xda-developers.com/honor-7/general/guide-beginners-how-to-root-update-fix-t3255452 ,still in bootloop
Click to expand...
Click to collapse
Try this
1 - Download B130
You can find the download links in.
http://forum.xda-developers.com/honor-7/general/plk-l01-firmwares-updates-official-beta-t3272205
http://forum.xda-developers.com/honor-7/general/models-stock-firmware-packages-honor-7-t3448747
http://www.modaco.com/forums/topic/...ck-rom-images-updated-1st-april-2016-plk-l01/
2 - Follow this guide
3 - Extract recovery.img, boot.img, cust.img and system.img from update.app file inside of B130 update file.
4 - Install minimal ADB and fastboot in your PC
5 - Install latest Google USB driver
6 - Reboot your PC.
7 - Connect your H7 to PC.
8 - Reboot H7 into fastboot mode (Vol- and power phone).
9 - Copy img files to ADB fastboot folder in your PC.
10 - Run ADB in your PC.
11 - Run ADB commands:
a) - fastboot devices - should reply with a device (yours)
b) - fastboot flash recovery recovery.img
c) - fastboot flash boot boot.img
d) - fastboot flash cust cust.img
e) - fastboot flash system system.img
f) - fastboot reboot12 - Copy the update.app from B370 zip file to a "dload" folder in your phone. Either in root of SDcard your root of phone.
13 - Turn off phone.
14 - Press simultaneously vol+- and power until you see any screen. Should be the update screen. It will update then reboot.
15 - Reboot and update until B180/190 version or B370.
16 - Factory reset after last update.
Hi,
Here is a long story of bricking my device, I wanted to downgrade my device from Oreo to Nougat, and somehow I installed wrong software, mine is RNE-L21 and after successful downgrade with this method:
https://www.youtube.com/watch?v=_3vqb8hPZIQ
version of software I installed: RNE-L21C461B153CUSTC461D001
my device was NEO-something, in settings it showed 3GB of RAM instead of 4GB, screen resolutution 1280x720 instead of fullHD and 32GB of internal memory instead of 64, so I wanted to change that.
This time I downloaded (not so sure about this now) proper version of firmware: RNE-L21C432B135CUSTC432D001, and used another method because previous method didnt work, link:
https://forum.xda-developers.com/showpost.php?p=76503686&postcount=46
the HuRUpdater scrpit worked fine, I booted up the device and nothing was changed, so I was like, well, ok then.
but then I noticed that my bootloader was locked, so I wanted to unlock it, and after typing the *fastboot oem unlock code* and selecting yes on my device, It rebooted and just stuck at the "Powered by andriod" logo.
I was trying to enter TWRP but id doesnt work, its stuck at the loading screen, I was unable to enter fastboot, but now I figured out that when I discharge it, I'm able to enter fastboot.
So now I'm stuck, I don't know what should I do.
I saw a guide for flashing .img files from UPDATE.APP, but that guide was for Oreo, and I've got diffrent .img files inside my Nougat UPDATE.APP so I don't want to risk:
https://forum.xda-developers.com/mate-10/help/mate-10-lite-bricked-t3794236
sentavn said:
you should format by using fastboot. First download your stock ROM and extract with Huawei Firmware Extracter. Select UPDATE.APP and extract following files:
erecovery_kernel.img
erecovery_ramdisk.img
erecovery_vbmeta.img
cust.img
erecovery_vendor.img
kernel.img
ramdisk.img
recovery_vbmeta.img
recovery_vendor.img
system.img
Reboot your device in to fastboot mode (recovery mode) and flash those files one by one:
fastboot flash erecovery_kernel erecovery_kernel.img
...
fastboot flash system system.img
//
Erase your userdata space:
fastboot -w
//reboot
fastboot reboot
Now go to your stock recovery and do factory reset, wide cache.
Now your device back to stock OREO
Click to expand...
Click to collapse
Any Ideas?
HOW I FIXED:
I downloaded this EMUI 5 Nougat, Thanks to bozka1:
https://androidhost.ru/5SZ
I extracted UPDATE.APP file using Huawei Update Extractor.
I was trying to flash everything via fastboot: BOOT.img, RECOVERY.img, RECOVERY2.img, CUST.img, SYSTEM.img but nothing helped me.
I found out what you can flash via fastboot here:
https://forum.xda-developers.com/general/general/huawei-fastboot-commands-t3850123
There was no hope for me, so I tried to flash USERDATA.img
fastboot flash userdata USERDATA.img
Click to expand...
Click to collapse
And then cmd promped something unusual:
target reported max download size of 471859200 bytes
sending 'userdata' (24576 KB)...
OKAY [ 0.646s]
writing 'userdata'...
(bootloader) success to erase cryypt info in oeminfo
OKAY [ 1.401s]
finished. total time: 2.049s
Click to expand...
Click to collapse
Then I proceeded to flash: BOOT.img, RECOVERY.img, RECOVERY2.img and CACHE.img
I didn't flash SYSTEM.img because I flashed it before like 1500 times.
My phone didn't work yet so I used the DLOAD method because RECOVERY finally worked, so I shut down the device and used three buttons combo:
First holding Volume Up, Volume Down and then pressing Power Button.
There is a documentation in the firmware I downloaded, SDcard must be in exFAT format.
Thank You bozka1.
voltzero2 said:
Hi,
Here is a long story of bricking my device, I wanted to downgrade my device from Oreo to Nougat, and somehow I installed wrong software, mine is RNE-L21 and after successful downgrade with this method:
https://www.youtube.com/watch?v=_3vqb8hPZIQ
version of software I installed: RNE-L21C461B153CUSTC461D001
my device was NEO-something, in settings it showed 3GB of RAM instead of 4GB, screen resolutution 1280x720 instead of fullHD and 32GB of internal memory instead of 64, so I wanted to change that.
This time I downloaded (not so sure about this now) proper version of firmware: RNE-L21C432B135CUSTC432D001, and used another method because previous method didnt work, link:
https://forum.xda-developers.com/showpost.php?p=76503686&postcount=46
the HuRUpdater scrpit worked fine, I booted up the device and nothing was changed, so I was like, well, ok then.
but then I noticed that my bootloader was locked, so I wanted to unlock it, and after typing the *fastboot oem unlock code* and selecting yes on my device, It rebooted and just stuck at the "Powered by andriod" logo.
I was trying to enter TWRP but id doesnt work, its stuck at the loading screen, I was unable to enter fastboot, but now I figured out that when I discharge it, I'm able to enter fastboot.
So now I'm stuck, I don't know what should I do.
I saw a guide for flashing .img files from UPDATE.APP, but that guide was for Oreo, and I've got diffrent .img files inside my Nougat UPDATE.APP so I don't want to risk:
https://forum.xda-developers.com/mate-10/help/mate-10-lite-bricked-t3794236
Any Ideas?
Click to expand...
Click to collapse
What is your original location, C461?
Which oeminfo you have flashed?
bozka1 said:
What is your original location, C461?
Which oeminfo you have flashed?
Click to expand...
Click to collapse
My original location is C432, I don't remember flashing any oeminfo
voltzero2 said:
My original location is C432, I don't remember flashing any oeminfo
Click to expand...
Click to collapse
Single SIM/dual SIM ?
Try reboot your phone into fastboot mode and use command
fastboot oem get-build-number
you'll see the number of your current firmware
bozka1 said:
Single SIM/dual SIM ?
Try reboot your phone into fastboot mode and use command
fastboot oem get-build-number
you'll see the number of your current firmware
Click to expand...
Click to collapse
It's dual sim,
the number of current firmware: System 5.1.0.98(08K5)
voltzero2 said:
It's dual sim,
the number of current firmware: System 5.1.0.98(08K5)
Click to expand...
Click to collapse
Okay, phone still locked ? What shows the screen in fastboot mode - phone and FRP ?
bozka1 said:
Okay, phone still locked ? What shows the screen in fastboot mode - phone and FRP ?
Click to expand...
Click to collapse
It says its unlucked:
https://imgur.com/a/LEDKWFr
I hope this link works
Download oeminfo
https://mega.nz/#!w4cX1QwT!TuFmfultDMDPt2b5yekrWREls7o5tSpveQFiWkBX6zg
Copy it to SD card.
Download TWRP
https://mega.nz/#!IodXAKBB!_VrqsMSxVw_NkXwfUIQb32mG_QAMd4HQ8_BtqmeHI94
and Service ROM
https://androidhost.ru/5SZ
. Extract dload folder from Service ROM and copy it to SD card.
Try to install TWRP: Copy the downloaded TWRP file to the Minimal ADB and fastboot folder, reboot to fastboot mode . Launch Minimal ADB , In the command window, enter the following commands one by one
- fastboot devices - this command will verify connection in fastbot mode (you will see your serial number)
-fastboot flash recovery2 TWRP-MATE.img
-fastboot reboot - the device will reboot
Now you can boot into TWRP mode using button Volume Up after rebooting.
Reboot to TWRP, Select Install, navigate to oeminfoRNE-L21C432 and confirm. Go back to the TWRP main menu, select Reboot and Power Off.
Now you can try flash the Service ROM with three buttons combo. GL!
bozka1 said:
Download oeminfo
https://mega.nz/#!w4cX1QwT!TuFmfultDMDPt2b5yekrWREls7o5tSpveQFiWkBX6zg
Copy it to SD card.
Download TWRP
https://mega.nz/#!IodXAKBB!_VrqsMSxVw_NkXwfUIQb32mG_QAMd4HQ8_BtqmeHI94
and Service ROM
https://androidhost.ru/5SZ
. Extract dload folder from Service ROM and copy it to SD card.
Try to install TWRP: Copy the downloaded TWRP file to the Minimal ADB and fastboot folder, reboot to fastboot mode . Launch Minimal ADB , In the command window, enter the following commands one by one
- fastboot devices - this command will verify connection in fastbot mode (you will see your serial number)
-fastboot flash recovery2 TWRP-MATE.img
-fastboot reboot - the device will reboot
Now you can boot into TWRP mode using button Volume Up after rebooting.
Reboot to TWRP, Select Install, navigate to oeminfoRNE-L21C432 and confirm. Go back to the TWRP main menu, select Reboot and Power Off.
Now you can try flash the Service ROM with three buttons combo. GL!
Click to expand...
Click to collapse
So I'll have to wait a little before I'll download Service ROM, my internet connection isn't the greatest, but I flashed Your TWRP and unfortunately it doesn't work;
If I hold the Power button and Volume Up - the same story as before, I see the loading TWRP screen and nothing happends,
If I let the device to boot up and then press only the Volume Up button - it says "Your device is booting up" and nothing happens.
By the way, what can happen when I'll use "fastboot flash recovery something.img" instead of recovery2?
EDIT:
I did some testing and Your TWRP doesn't boot at all on my device, I flashed another one, Catuva21 3.1.1 Nougat, and that is the one that I had before - it is booting but never loads.
voltzero2 said:
By the way, what can happen when I'll use "fastboot flash recovery something.img" instead of recovery2?
Click to expand...
Click to collapse
TWRP will automatically overwrite Stock recovery, it's impossible to flash something from dload without Stock recovery .
Using command "recovery2" you will install TWRP over eRecovery .
Try flash Service ROM from SD card without TWRP & oeminfo flashing, but Im not sure... your system is heavily damaged and incomplete .
bozka1 said:
TWRP will automatically overwrite Stock recovery, it's impossible to flash something from dload without Stock recovery .
Using command "recovery2" you will install TWRP over eRecovery .
Try flash Service ROM from SD card without TWRP & oeminfo flashing, but Im not sure... your system is heavily damaged and incomplete .
Click to expand...
Click to collapse
So the phone would boot up the TWRP without pressing anything? Damn, I might have done that typo error... Do You know if I can restore the stock recovery from the UPDATE.APP file? I mean flash it
voltzero2 said:
So the phone would boot up the TWRP without pressing anything? Damn, I might have done that typo error... Do You know if I can restore the stock recovery from the UPDATE.APP file? I mean flash it
Click to expand...
Click to collapse
Use Huawei Update Extractor and extract RECOVERY.img , copy it to the "Minimal ADB and fastboot" folder . Command :
fastboot flash recovery RECOVERY.img
bozka1 said:
Use Huawei Update Extractor and extract RECOVERY.img , copy it to the "Minimal ADB and fastboot" folder . Command :
fastboot flash recovery RECOVERY.img
Click to expand...
Click to collapse
Yeah, I've done it already, unfortunately nothing changed. How about BOOT.img? Can this influence something?
EDIT:
I also wonder about just following the steps in my first post, I've got UPDATE.APP for Oreo, but I don't know if it will only make it worse.
bozka1 said:
Download oeminfo
https://mega.nz/#!w4cX1QwT!TuFmfultDMDPt2b5yekrWREls7o5tSpveQFiWkBX6zg
Copy it to SD card.
Download TWRP
https://mega.nz/#!IodXAKBB!_VrqsMSxVw_NkXwfUIQb32mG_QAMd4HQ8_BtqmeHI94
and Service ROM
https://androidhost.ru/5SZ
. Extract dload folder from Service ROM and copy it to SD card.
Try to install TWRP: Copy the downloaded TWRP file to the Minimal ADB and fastboot folder, reboot to fastboot mode . Launch Minimal ADB , In the command window, enter the following commands one by one
- fastboot devices - this command will verify connection in fastbot mode (you will see your serial number)
-fastboot flash recovery2 TWRP-MATE.img
-fastboot reboot - the device will reboot
Now you can boot into TWRP mode using button Volume Up after rebooting.
Reboot to TWRP, Select Install, navigate to oeminfoRNE-L21C432 and confirm. Go back to the TWRP main menu, select Reboot and Power Off.
Now you can try flash the Service ROM with three buttons combo. GL!
Click to expand...
Click to collapse
Do I have to install oeminfo to be able to use the "three buttons combo"? Because I tried it today and it doesn't work, phone is just stuck at "Your device is booting.." screen, guess I'm out of luck
I fixed it, solution will be attached to first post.
Thanks to bozka1 who gave me this helpful link:
https://androidhost.ru/5SZ
voltzero2 said:
I fixed it, solution will be attached to first post.
Thanks to bozka1 who gave me this helpful link:
https://androidhost.ru/5SZ
Click to expand...
Click to collapse
You're welcome
Hi help me
Bozka1
My huawei mate 10 lite is brick stock on erecovery what can i do now
Lj08 said:
My huawei mate 10 lite is brick stock on erecovery what can i do now
Click to expand...
Click to collapse
Hi, have you tried to do something with your phone? Can you provide some info?
voltzero2 said:
Hi, have you tried to do something with your phone? Can you provide some info?
Click to expand...
Click to collapse
Voltzero2
I try factory reset wipe catch and no result just going back to erecovery
Lj08 said:
Voltzero2
I try factory reset wipe catch and no result just going back to erecovery
Click to expand...
Click to collapse
Alright, so did it just happened randomly or did you tried to do something with your phone? Did you unlocked bootloader or flashed custom recovery etc? You need to explain what happened, that's quite important if you want someone to help you.
Things are changing with the advent of project treble and seamless updates. OnePlus will no longer release ROMs flashable via recovery (either stock) because is no more needed. The updates will be done on the slot not used for example if you are using slot a the update will be installed on slot b and the slot b will be set as default. If you brick and you are in bootloop how you can restore the rom? You can't with Stock ROM you have, because the zip can be only installed via Update Engine, so what can you do? Flash a stock rom via fastboot. I have extracted all images from the stock zip and i have made a new zip with the Fastboot ROM with a flash-all.bat included. This will work only if your bootloader is unlocked. This will erase all your data and will wipe your internal storage.
HOW TO FLASH
This version is only for not branded devices
Download the zip;
Unpack the zip in a folder;
Reboot the OnePlus Nord in fastboot-bootloader mode (Power and volume + and volume-);
Connect the OnePlus Nord to PC;
Run flash-all.bat flasher you need;
Wait until the process end;
The phone will automatically reboot.
DOWNLOAD
All roms on Sourceforge: https://sourceforge.net/projects/fastbootroms/files/OnePlus Nord/
BRANDED PHONE
For now branded device are not supported
MANUAL FLASH: Windows - OSX - Linux
If you want to manual flash these roms these are the commands (You need the latest sdk platform tools, you can find it here
Is reccomended to format data or the rom cannot boot:
Code:
fastboot -w
Others Commands to flash a fastboot rom
Code:
fastboot flash boot boot.img
fastboot flash dtbo dtbo.img
fastboot flash modem modem.img
fastboot flash recovery recovery.img
fastboot --disable-verity flash vbmeta vbmeta.img
fastboot --disable-verity flash vbmeta_system vbmeta_system.img
fastboot reboot fastboot
fastboot flash abl abl.img
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash devcfg devcfg.img
fastboot flash dsp dsp.img
fastboot flash featenabler featenabler.img
fastboot flash hyp hyp.img
fastboot flash imagefv imagefv.img
fastboot flash keymaster keymaster.img
fastboot flash logo logo.img
fastboot flash oem_stanvbk oem_stanvbk.img
fastboot flash odm odm.img
fastboot flash qupfw qupfw.img
fastboot flash storsec storsec.img
fastboot flash tz tz.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash xbl xbl.img
fastboot flash xbl_config xbl_config.img
fastboot flash system system.img
fastboot flash vendor vendor.img
fastboot flash product product.img
fastboot reboot
REMEMBER
"Invalid sparce file format at header magic" is not an error, you need to wait a bit when you see that string, just wait.
If the device automatically reboot in Stock Recovery mode don't reboot it and wait the flash end.
These ROMs can't be used to update or downgrade your phone but just to restore your phone.
If the rom seems doesn't start go in recovery stock and follow this guideline: English -> Wipe data and cache -> Erase everything.
If you want to rebrand your phone from HydrogenOS to OxygenOS you can follow this guide: Rebrand Guide
If you want you can use also my tool to flash Factory Images, unlock bootloader, flash twrp or to understand if the device is recognized: https://toolaio.tk/
If you got some problems like write error or no partition, check this: https://forum.xda-developers.com/showpost.php?p=76658555&postcount=34
DONATE LINK
If you want to support this and others my projects please consider making a donation, thanks.
I was already waiting for it.:laugh:
mauronofrio said:
Things are changing with the advent of project treble and seamless updates. OnePlus will no longer release ROMs flashable via recovery (either stock) because is no more needed. The updates will be done on the slot not used for example if you are using slot a the update will be installed on slot b and the slot b will be set as default. If you brick and you are in bootloop how you can restore the rom? You can't with Stock ROM you have, because the zip can be only installed via Update Engine, so what can you do? Flash a stock rom via fastboot. I have extracted all images from the stock zip and i have made a new zip with the Fastboot ROM with a flash-all.bat included. This will work only if your bootloader is unlocked. This will erase all your data and will wipe your internal storage.
HOW TO FLASH
This version is only for not branded devices
Download the zip;
Unpack the zip in a folder;
Reboot the OnePlus Nord in fastboot-bootloader mode (Power and volume + and volume-);
Connect the OnePlus Nord to PC;
Run flash-all.bat flasher you need;
Wait until the process end;
The phone will automatically reboot.
DOWNLOAD
All roms on Sourceforge: https://sourceforge.net/projects/fastbootroms/files/OnePlus Nord/
BRANDED PHONE
For now branded device are not supported
MANUAL FLASH: Windows - OSX - Linux
If you want to manual flash these roms these are the commands (You need the latest sdk platform tools, you can find it here
Is reccomended to format data or the rom cannot boot:
Others Commands to flash a fastboot rom
REMEMBER
"Invalid sparce file format at header magic" is not an error, you need to wait a bit when you see that string, just wait.
If the device automatically reboot in Stock Recovery mode don't reboot it and wait the flash end.
These ROMs can't be used to update or downgrade your phone but just to restore your phone.
If the rom seems doesn't start go in recovery stock and follow this guideline: English -> Wipe data and cache -> Erase everything.
If you want to rebrand your phone from HydrogenOS to OxygenOS you can follow this guide: Rebrand Guide
If you want you can use also my tool to flash Factory Images, unlock bootloader, flash twrp or to understand if the device is recognized: https://toolaio.tk/
If you got some problems like write error or no partition, check this: https://forum.xda-developers.com/showpost.php?p=76658555&postcount=34
DONATE LINK
If you want to support this and others my projects please consider making a donation, thanks.
Click to expand...
Click to collapse
I an waiting for TWRP...
cieffe54 said:
I an waiting for TWRP...
Click to expand...
Click to collapse
Check development thread
cieffe54 said:
I an waiting for TWRP...
Click to expand...
Click to collapse
And i am waiting for end of corona pandemic.
Kollachi said:
And i am waiting for end of corona pandemic.
Click to expand...
Click to collapse
But i shared it too...
Hello and thank you for the fastboot roms !
How To Use This!
mauronofrio said:
Things are changing with the advent of project treble and seamless updates. OnePlus will no longer release ROMs flashable via recovery (either stock) because is no more needed. The updates will be done on the slot not used for example if you are using slot a the update will be installed on slot b and the slot b will be set as default. If you brick and you are in bootloop how you can restore the rom? You can't with Stock ROM you have, because the zip can be only installed via Update Engine, so what can you do? Flash a stock rom via fastboot. I have extracted all images from the stock zip and i have made a new zip with the Fastboot ROM with a flash-all.bat included. This will work only if your bootloader is unlocked. This will erase all your data and will wipe your internal storage.
HOW TO FLASH
This version is only for not branded devices
Download the zip;
Unpack the zip in a folder;
Reboot the OnePlus Nord in fastboot-bootloader mode (Power and volume + and volume-);
Connect the OnePlus Nord to PC;
Run flash-all.bat flasher you need;
Wait until the process end;
The phone will automatically reboot.
DOWNLOAD
All roms on Sourceforge: https://sourceforge.net/projects/fastbootroms/files/OnePlus Nord/
BRANDED PHONE
For now branded device are not supported
MANUAL FLASH: Windows - OSX - Linux
If you want to manual flash these roms these are the commands (You need the latest sdk platform tools, you can find it here
Is reccomended to format data or the rom cannot boot:
Code:
fastboot -w
Others Commands to flash a fastboot rom
Code:
fastboot flash boot boot.img
fastboot flash dtbo dtbo.img
fastboot flash modem modem.img
fastboot flash recovery recovery.img
fastboot --disable-verity flash vbmeta vbmeta.img
fastboot --disable-verity flash vbmeta_system vbmeta_system.img
fastboot reboot fastboot
fastboot flash abl abl.img
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash devcfg devcfg.img
fastboot flash dsp dsp.img
fastboot flash featenabler featenabler.img
fastboot flash hyp hyp.img
fastboot flash imagefv imagefv.img
fastboot flash keymaster keymaster.img
fastboot flash logo logo.img
fastboot flash oem_stanvbk oem_stanvbk.img
fastboot flash odm odm.img
fastboot flash qupfw qupfw.img
fastboot flash storsec storsec.img
fastboot flash tz tz.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash xbl xbl.img
fastboot flash xbl_config xbl_config.img
fastboot flash system system.img
fastboot flash vendor vendor.img
fastboot flash product product.img
fastboot reboot
REMEMBER
"Invalid sparce file format at header magic" is not an error, you need to wait a bit when you see that string, just wait.
If the device automatically reboot in Stock Recovery mode don't reboot it and wait the flash end.
These ROMs can't be used to update or downgrade your phone but just to restore your phone.
If the rom seems doesn't start go in recovery stock and follow this guideline: English -> Wipe data and cache -> Erase everything.
If you want to rebrand your phone from HydrogenOS to OxygenOS you can follow this guide: Rebrand Guide
If you want you can use also my tool to flash Factory Images, unlock bootloader, flash twrp or to understand if the device is recognized: https://toolaio.tk/
If you got some problems like write error or no partition, check this: https://forum.xda-developers.com/showpost.php?p=76658555&postcount=34
DONATE LINK
If you want to support this and others my projects please consider making a donation, thanks.
Click to expand...
Click to collapse
Oneplus Nord oxygen os install guide
Get OEM Drivers from https://oneplususbdrivers.com/download-oneplus-usb-driver/
Download Oxygen OS 10.5.4 for your compatible devices from https://sourceforge.net/projects/fastbootroms/files/OnePlus Nord/
(Boot loader Must be Unlocked)
If still able to boot into any version of Android:
1. Install Oneplus OEM Drivers
2. Open Settings
3. Click About
4. Find the build number and click the Build number Severn times until you get a message saying developer Options have been enabled.
5. Enable ADB USB Debugger
6. Unzip the Oxygen OS File
7. Open CMD and run it as Administrator
8. Plug Your Oneplus Nord into your PC
9. Type into CMD cd and drag the Oxygen OS Folder over CMD, then Click Enter
10. This will make the link before the next line quite long.
11. Then Type into CMD “adb reboot bootloader” (This will make your Phone Reboot into Fastboot)
If You are Unable to boot into any Operating System:
1. Install Oneplus OEM Drivers
2. Unzip the Oxygen OS File
3. Open CMD and run it as Administrator
4. Type into CMD cd and drag the Oxygen OS Folder over CMD, then Click Enter
5. This will make the link before the next line quite long.
6. Plug Your Oneplus Nord into your Computer
7. When your phone is powered off, Hold Volume Up, Volume Down and the Power Button until you get the Oneplus Logo with fastboot Beneath.
Once in the Bootloader:
1. Type fastboot devices to confirm that your device has been recognised by your PC.
2. After this Open the Oxygen OS Folder and double click Flash-All.adb and It will open in command Prompt.
3. This will take a long time but wait until the phone has booted up into your phones setup (Do Not touch the Phone or Computer).
4. Setup Your Phone but don’t setup anything as we need to wipe it again, so skip through everything.
5. Once in the primary OS connect to WIFI
6. Go to Settings and Update your phone to the latest version, you will get a message prompting you that the Boot loader is unlocked etc, Ignore this and continue.
7. Click the reboot button when prompted, your Software will update to the latest version of Oxygen OS.
Once Updated:
1. Open Settings
2. Click About
3. Find the build number and click the Build number Severn times until you get a message saying developer Options have been enabled.
4. Enable ADB USB Debugger
5. Unzip the Oxygen OS File
6. Open CMD and run it as Administrator
7. Plug Your Oneplus Nord into your PC
8. Type into CMD cd and drag the Oxygen OS Folder over CMD, then Click Enter
9. This will make the link before the next line quite long.
10. Then Type into CMD “adb reboot bootloader” (This will make your Phone Reboot into Fastboot).
11. Once in Fastboot type “fastboot OEM lock” then your phone will prompt you if you want to Lock the bootloader.
12. Use the volume button to scroll down and press enter to confirm that you want to lock your bootloader.
13. When locked your phone will reboot and it will wipe your operating system and reboot your device into setup.
14. You can now setup your phone as you wish.
there's not oneplus widget? i can't find it
Jackmitchell62 said:
Things are changing with the advent of project treble and seamless updates. OnePlus will no longer release ROMs flashable via recovery (either stock) because is no more needed. The updates will be done on the slot not used for example if you are using slot a the update will be installed on slot b and the slot b will be set as default. If you brick and you are in bootloop how you can restore the rom? You can't with Stock ROM you have, because the zip can be only installed via Update Engine, so what can you do? Flash a stock rom via fastboot. I have extracted all images from the stock zip and i have made a new zip with the Fastboot ROM with a flash-all.bat included. This will work only if your bootloader is unlocked. This will erase all your data and will wipe your internal storage.
HOW TO FLASH
This version is only for not branded devices
Download the zip;
Unpack the zip in a folder;
Reboot the OnePlus Nord in fastboot-bootloader mode (Power and volume + and volume-);
Connect the OnePlus Nord to PC;
Run flash-all.bat flasher you need;
Wait until the process end;
The phone will automatically reboot.
DOWNLOAD
All roms on Sourceforge: https://sourceforge.net/projects/fastbootroms/files/OnePlus Nord/
BRANDED PHONE
For now branded device are not supported
MANUAL FLASH: Windows - OSX - Linux
If you want to manual flash these roms these are the commands (You need the latest sdk platform tools, you can find it here
Is reccomended to format data or the rom cannot boot:
Others Commands to flash a fastboot rom
Oneplus Nord oxygen os install guide
Get OEM Drivers from https://oneplususbdrivers.com/download-oneplus-usb-driver/
Download Oxygen OS 10.5.4 for your compatible devices from https://sourceforge.net/projects/fastbootroms/files/OnePlus Nord/
(Boot loader Must be Unlocked)
If still able to boot into any version of Android:
1. Install Oneplus OEM Drivers
2. Open Settings
3. Click About
4. Find the build number and click the Build number Severn times until you get a message saying developer Options have been enabled.
5. Enable ADB USB Debugger
6. Unzip the Oxygen OS File
7. Open CMD and run it as Administrator
8. Plug Your Oneplus Nord into your PC
9. Type into CMD cd and drag the Oxygen OS Folder over CMD, then Click Enter
10. This will make the link before the next line quite long.
11. Then Type into CMD “adb reboot bootloader” (This will make your Phone Reboot into Fastboot)
If You are Unable to boot into any Operating System:
1. Install Oneplus OEM Drivers
2. Unzip the Oxygen OS File
3. Open CMD and run it as Administrator
4. Type into CMD cd and drag the Oxygen OS Folder over CMD, then Click Enter
5. This will make the link before the next line quite long.
6. Plug Your Oneplus Nord into your Computer
7. When your phone is powered off, Hold Volume Up, Volume Down and the Power Button until you get the Oneplus Logo with fastboot Beneath.
Once in the Bootloader:
1. Type fastboot devices to confirm that your device has been recognised by your PC.
2. After this Open the Oxygen OS Folder and double click Flash-All.adb and It will open in command Prompt.
3. This will take a long time but wait until the phone has booted up into your phones setup (Do Not touch the Phone or Computer).
4. Setup Your Phone but don’t setup anything as we need to wipe it again, so skip through everything.
5. Once in the primary OS connect to WIFI
6. Go to Settings and Update your phone to the latest version, you will get a message prompting you that the Boot loader is unlocked etc, Ignore this and continue.
7. Click the reboot button when prompted, your Software will update to the latest version of Oxygen OS.
Once Updated:
1. Open Settings
2. Click About
3. Find the build number and click the Build number Severn times until you get a message saying developer Options have been enabled.
4. Enable ADB USB Debugger
5. Unzip the Oxygen OS File
6. Open CMD and run it as Administrator
7. Plug Your Oneplus Nord into your PC
8. Type into CMD cd and drag the Oxygen OS Folder over CMD, then Click Enter
9. This will make the link before the next line quite long.
10. Then Type into CMD “adb reboot bootloader” (This will make your Phone Reboot into Fastboot).
11. Once in Fastboot type “fastboot OEM lock” then your phone will prompt you if you want to Lock the bootloader.
12. Use the volume button to scroll down and press enter to confirm that you want to lock your bootloader.
13. When locked your phone will reboot and it will wipe your operating system and reboot your device into setup.
14. You can now setup your phone as you wish.
Click to expand...
Click to collapse
Or simply use MSM tool ?
https://forum.xda-developers.com/oneplus-nord/how-to/opnord-unbrick-tool-to-restore-device-t4148415
Reboot in recovery
Hello everyone, I need help.
I got the message "File system raw not supported." after executing the flash_all.bat and
Code:
boot_b, dtbo, modem_b, recovery, vbmeta, vbmeta_system,
was sent with status
Code:
OKAY
(the first part of the script, as far as I can see), then is supposed to reboot on fastboot and stays at
Code:
<waiting for any device>
, here is when my phone restarts in recovery instead (it says "fastbootd" in the upper part and a menu to select chinesse or english, but it's recovery mode, right?), then the first time I wited for 15 minutes but nothing happened, so I selected reboot into fastboot in recovery mode, then in CMD I got the message "fastboot: error Failed to boot into userspace fastboot; one or more components might be unbootable", and the seccond part of the script was executed, but with
Code:
FAILED (remote: 'Flashing is not allowed for Critical Partitions')
status in the writing process, and after,
Code:
"Invalid sparse file format at header magic"
with
Code:
FAILED (remote: 'Partition not found')
when trying to write system, vendor and product. My phone restarted and looked normar but wifi didn't work, and the UI started to fail after the configuration.
So I tried again, but without rebooting from recovery; how much time do I have to wait there?, maybe this will not work.
Please if someone knows how to solve my problem I'll be glad for the help.
MSM TOOL
https://forum.xda-developers.com/oneplus-nord/how-to/opnord-unbrick-tool-to-restore-device-t4148415
I succeeded from linux, everything seems to work fine now.
I just have one question, there's one file missing
fastboot flash storsec storsec.img
Is supposed to be like that or is that an important file missed?
That file doesn't exists in the 10.5.5-INDIA-NordOxygen_14_OTA_007_all_2008180229 zip file
I bricked my device and nothing (what i try) worked.
Hello Guys,
Thanks for the Roms and also for twrp @ mauronofrio!
If i try to flash in fastboot the roms, i get different fails:
the first part of commands are okay until "fastboot reboot fastboot"
than, until "fastboot flash xbl_config xbl_config.img" i get:
"writing 'xbl_config'...
FAILED (remote: Flashing is not allowed for Critical Partitions)"
and for the lasts, i get:
FAILED (remote: Partition not found)
I read that some windows-user have the same Problem and therrefore the Problem is not the bricked phone, is it right?
Someone knows the same Problem in linux? I prefer a solution without windows (msm-tool).
I tried to root and flash with twrp, now i know, it's impossible to flash zips until now. I try some other things with twrp, it's possible that i delete some partitions?
Someone have a good solution?
thanks for reading and support
Hi,
Few questions:
Has Global rom OP dialer? Can be enabled auto call recording with root or adb? I know abut Skvalex.
Can I flash 10.5.5 Global at 10.5.9 EEA (flash_all.bat)?
Getting stuck on odm and vendor flashing. It will not flash odm and vendor no file exists message (using flash all bat). Any help will be greatly appreciated.
Update: got it back to stock using edl mode.
You can flash this way. When you enter from the fastboot to the fastbootD mode Windows thinks it's a new device and doesn't recognize it. If you open device manager from control panel it will showns as unknow device. So all you have to do is install the driver again. Then you can flash anything you want in fastbootD.
-
What does "unbranded" mean here? Will I get OTA updates? Will this relock the bootloader?
delete
Hi all
i want to install TWRP on my Doogee N20PRO . i cannot find a TWRP File on the internet to install. I could find some for the N20 but not for the N20PRO. it´s an Helios P60 Processor with an MTK6771. I tried to install the HAVOC 3.7 but i get the Message "writing 1/15 failed (remote: this partition doesn´t exist)
beinfo said:
Hi all
i want to install TWRP on my Doogee N20PRO . i cannot find a TWRP File on the internet to install. I could find some for the N20 but not for the N20PRO. it´s an Helios P60 Processor with an MTK6771. I tried to install the HAVOC 3.7 but i get the Message "writing 1/15 failed (remote: this partition doesn´t exist)
Click to expand...
Click to collapse
This is simple about TWRP: Your phone have МТК Helio Р60 MT6771V/CA WITH Android 10.0 and it's a NEW phone now. So no developments yet.
For install GSI ROMs your need unlock bootloader and after follow the correct instructions to new phones shipped with A10!
If you only want install GSI so I suggest:
1- Have stock ROM first, always!!;
2- With security 1- you should unlock bootloader;
3- You can install GSI with stock recovery without problems.
The only part is: you cannot backup userdata.....
DragonPitbull said:
This is simple about TWRP: Your phone have МТК Helio Р60 MT6771V/CA WITH Android 10.0 and it's a NEW phone now. So no developments yet.
For install GSI ROMs your need unlock bootloader and after follow the correct instructions to new phones shipped with A10!
If you only want install GSI so I suggest:
1- Have stock ROM first, always!!;
2- With security 1- you should unlock bootloader;
3- You can install GSI with stock recovery without problems.
The only part is: you cannot backup userdata.....
Click to expand...
Click to collapse
Cool This helps already a lot.
i unlocked the Bootloader properly, but then i got a partition error. I assume i´ve an error in the command line. The phone was anyway only an interim solution till my POco F2 was back from repair. now i use it as a playground.
fastboot erase system - there i get a partition error.
erasing the User data was sucessful
but then
fastboot flash system system.img it stops at step 1/15 again for the partition error (partition doesn´t exist) Stock rom is available.
somebody knows the options i´ve to add to the command line?
beinfo said:
The phone was anyway only an interim solution till my POco F2 was back from repair. now i use it as a playground.
fastboot erase system - there i get a partition error.
erasing the User data was sucessful
but then
fastboot flash system system.img it stops at step 1/15 again for the partition error (partition doesn´t exist) Stock rom is available.
somebody knows the options i´ve to add to the command line?
Click to expand...
Click to collapse
Try but REMENBER I am not responsible for any errors. Bootloader should unlocked by adb-fastboot!!
Spoiler: Instructions
1. You need know the difference about fastboot and FASTBOOTD in your device!!
Your device has bootloader mode: recovery - fastboot - reboot (system)
Stock recovery has very options: reboot system - reboot to bootloader - wipe - Enter fastboot - ...
reboot to bootloader => normal fastboot
Enter fastboot => FASTBOOTD
FASTBOOTD => some options
2. Device in fastboot
Code:
fastboot --disable-verification flash vbmeta vbmeta.img
vbmeta file from stock ROM or pulled from device
3.
Code:
fastboot -w
4.
Code:
fastboot reboot fastboot
(you MUST be at the FASTBOOTD menu now. If not, you will not be able to flash the GSI successfully)
5.
Code:
fastboot erase system
or
Code:
fastboot delete-logical-partition system
6.
Code:
fastboot delete-logical-partition product
- deletes the product partition, allowing a larger system partition
I not need resize-logical-partition product. But if you want:
You will need a larger system partition to flash a GSI. There are 2 ways to achieve this
6A. fastboot resize-logical-partition product 509344768
6B. fastboot resize-logical-partition system 3089272064 or 3889272064
resizes product and system partitions. This gives you about 3GB of system partitions. You can adjust or arrive at your own numbers if you want different sizes.
7.
Code:
fastboot --disable-verity --disable-verification flash system GSI.img
8.
Code:
fastboot -w
for confirm great & fast start GSI
9.
Code:
fastboot reboot bootloader
9A.
Code:
fastboot erase userdata
for confirm and boot clean
10. Reboot to system
Code:
fastboot reboot
Enjoy
I also have an N20 Pro which I received Dec 2020. Had some trouble setting it up. I got the OEM ROM from Doogee customer support and was able to extract the boot image and patch it with Magisk. I then burned it with the SP Flash tool. It wouldn't boot until I burned a special vbmeta.img to turn off encryption. Now it's working fine.
Sorry this doesn't help you with TWRP but I think most people looking for TWRP are really looking to root their phone.
beinfo said:
Hi all
i want to install TWRP on my Doogee N20PRO . i cannot find a TWRP File on the internet to install. I could find some for the N20 but not for the N20PRO. it´s an Helios P60 Processor with an MTK6771. I tried to install the HAVOC 3.7 but i get the Message "writing 1/15 failed (remote: this partition doesn´t exist)
Click to expand...
Click to collapse
Okay so what ive seen is that you should avoid flashing custom roms via adb fastboot especially with our doogee phones, and also there are many incompatiable roms so what you will need is to unlock bootloader and do the whole twrp install thing adn also install magisk
before hand install treble info from google playstore and take down the information "arm64 a/b" and search for roms with that information to install custom os/rom/gsi properly. GSI versions are more preferred if your phone supports treblle
if your twrp keeps getting wiped after reboot open file :mount your system and connect to pc via usbcable (mtp if not showing disable mtp and re- enable it )
now got to where build.prop is saved there will be a file called recovery from boot.p , copy the file to pc , open with notepad, remove everything , save and copy back to phone (overwrite)
then go ahead and install magisk
make sure your magisk is working install edxposed, riru core , and busybox ndk get the apps you need for them (edxposed manager...) and then instal and activate a module which you can test if its working(if framework is active in edxposed manager and the module working correctly then you can go ahead and
Install custom os through twrp
follow these instructions ( https://forum.xda-developers.com/t/...lexperience-10-gsi-android-10-stable.4081685/ ) with your custom rom (corvus, havoc, lineage...
(the g-apps didnt flash for me (error code 64) but i just rebooted and everything was working fine (including gapps but camera sucked (doogee's rear camera setup was just terrible))
https://forum.xda-developers.com/t/...lexperience-10-gsi-android-10-stable.4081685/
** i can confirm follow instructions properly and it should work (i used this pixel experience on my doogee n20 make sure you unzip the .xz file and youre flashing a .img file
**also make sure its the gsi file (
Can anyone help? For the life of me I can't get it to go into recovery mode or anything of the like after attempting a flash of official firmware.
It's not being picked up by ADB, fastboot OR Lenovo's smart recovery crap.
brownie96 said:
Can anyone help? For the life of me I can't get it to go into recovery mode or anything of the like after attempting a flash of official firmware.
Click to expand...
Click to collapse
This also happened to my Legion Duel 2 after using RSA.. its stuck on FastBoot.. tried connecting to RSA again and an error saying "Doesn't match the appropriate software"
my Duel 2 is now stucked on FastBoot and cant select other options like START or Recovery Mode..
Now im trying to use QFil but im having an error:
"Download fail: Sahara Fail: QSaharaServer Fail: Process Fail"
Btw these are the files in the ROM 12.5.188ST thats appearing when selecting PROGRAMMER:
and on the XML:
Patch:
Tried:
prog_firehose_ddr.elf
rawprogram_unparsed0 (also tried selecting all files)
patch0 (also tried selecting all files)
Sorry this is my 1st time doing this stuff and i have no idea..
Hope someone can help me fix my Duel 2. Thank you
try flashing a meta build with the ddr firehose, then fastboot flash your persist image. its worked for me twice now
ฉันลองทุกขั้นตอนแล้วแต่ทำไม่ได้ โปรดอธิบายโดยละเอียดว่าคืออะไร
ฉันลองทุกขั้นตอนแล้วแต่ทำไม่ได้ โปรดอธิบายโดยละเอียดว่าคืออะไร
ฉันลองทุกขั้นตอนแล้วแต่ทำไม่ได้ โปรดอธิบายโดยละเอียดว่าคืออะไร
waabby said:
Duel 2 ของฉันติดอยู่ที่ FastBoot และไม่สามารถเลือกตัวเลือกอื่น ๆ เช่น START หรือ Recovery Mode..
ตอนนี้ฉันกำลังพยายามใช้ QFil แต่มีข้อผิดพลาด:
"การดาวน์โหลดล้มเหลว: Sahara ล้มเหลว: QSaharaServer ล้มเหลว: กระบวนการล้มเหลว"
View attachment 5518121
นี่เป็นไฟล์ใน ROM 12.5.188ST ที่ปรากฏขึ้นเมื่อเลือกโปรแกรมเมอร์:
View attachment 5518125
และใน XML:
View attachment 5518129
ปะ:
View attachment 5518131
พยายาม:
prog_firehose_ddr.elf
rawprogram_unparsed0 (ลองเลือกไฟล์ทั้งหมดด้วย)
patch0 (ลองเลือกไฟล์ทั้งหมดด้วย)
ขออภัย นี่เป็นครั้งแรกที่ฉันทำสิ่งนี้และฉันไม่รู้ ..
หวังว่าใครบางคนสามารถช่วยฉันแก้ไข Duel 2 ของฉันได้ ขอบคุณ
Click to expand...
Click to collapse
ใน Qfil การกำหนดค่า ให้ใน UFS
try going into your firehose options and select erase all before flashing. other than that im uploading all the partitions ive made copies of using qfil. You can try flashing them over one by one in qfil or see if fastboot flash will work . https://mega.nz/folder/TqxSjYrD#l3GM8SQgJcxhVrSeXMLW7Q
tinman4209333 said:
try going into your firehose options and select erase all before flashing. other than that im uploading all the partitions ive made copies of using qfil. You can try flashing them over one by one in qfil or see if fastboot flash will work . https://mega.nz/folder/TqxSjYrD#l3GM8SQgJcxhVrSeXMLW7Q
Click to expand...
Click to collapse
great work, its really appreciated. will these work on cn and global roms? or are they rom specific? and would it be possible to write a fastboot flashable script to make flashing the partitions easier? (for noobs like me who don't know how to flash them all manually) thanks again
Lizzo said:
great work, its really appreciated. will these work on cn and global roms? or are they rom specific? and would it be possible to write a fastboot flashable script to make flashing the partitions easier? (for noobs like me who don't know how to flash them all manually) thanks again
Click to expand...
Click to collapse
completely forgot to specify which rom it was lol. its global
if you use fastboot flash commands you just go off of the file name . fastboot flash boot boot_a.bin fastboot flash vbmeta vbmeta_a.bin . im pretty sure you can reuse the same file for both partitions. fastboot flash boot_a boot.bin | fastboot flash boot_b boot_a.bin etc. to make a windows script you'd write out each command in notepad then save it as a bat file.
You can also install them all manually using qfil.
-1. put phone into edl mode
-2. select firehose_ddr under the flatbuild section
-3. click on tools / partition manager
-4. right click a partition
-5. manage partition data
-6. load image (if you want you can erase the partition before loading the image )
-7. pick matching file, it immediately flashes it to your phone
-8. rinse and repeat
how i got out of the bootlop was using the file from rescue smart assistant. id flash it in qfil using the meta build option, and ddr firehose. then boot up into the bootloader and flash a persist image I had previously saved. if it doesnt work for you I can upload that image and see if that helps
tinman4209333 said:
completely forgot to specify which rom it was lol. its global
if you use fastboot flash commands you just go off of the file name . fastboot flash boot boot_a.bin fastboot flash vbmeta vbmeta_a.bin . im pretty sure you can reuse the same file for both partitions. fastboot flash boot_a boot.bin | fastboot flash boot_b boot_a.bin etc. to make a windows script you'd write out each command in notepad then save it as a bat file.
You can also install them all manually using qfil.
-1. put phone into edl mode
-2. select firehose_ddr under the flatbuild section
-3. click on tools / partition manager
-4. right click a partition
-5. manage partition data
-6. load image (if you want you can erase the partition before loading the image )
-7. pick matching file, it immediately flashes it to your phone
-8. rinse and repeat
how i got out of the bootlop was using the file from rescue smart assistant. id flash it in qfil using the meta build option, and ddr firehose. then boot up into the bootloader and flash a persist image I had previously saved. if it doesnt work for you I can upload that image and see if that helps
Click to expand...
Click to collapse
thanks a lot. i can try that. are you in the legion group on telegram? we could sure use your help lol
Lenovo legion pro duel comentarios y más
You can view and join @lenovolegiongamers right away.
t.me
tinman4209333 said:
try going into your firehose options and select erase all before flashing
Click to expand...
Click to collapse
I would not recommend that step.
&(*) said:
I would not recommend that step.
Click to expand...
Click to collapse
I had the same issue of it not flashing and it fixed the problem . When your stuck with a $500+ paperweight and nothing else works ya get kind of desperate after awhile lol. Figured it'd have a better chance of working with a clean slate then trying to write over something that's broken
tinman4209333 said:
try flashing a meta build with the ddr firehose, then fastboot flash your persist image. its worked for me twice now
Click to expand...
Click to collapse
how do you fast boot flash. mine not connecting to fast boot
my qfil flashes work but still no boot
kofijordan said:
how do you fast boot flash,
Click to expand...
Click to collapse
Make sure the device is off, hold the volume down button and turn it on, will boot into the loader menu, plug in to usb side port and type fastboot reboot fastboot, it will reboot into fastbootd and now can flash through fastboot.
&(*) said:
Make sure the device is off, hold the volume down button and turn it on, will boot into the loader menu, plug in to usb side port and type fastboot reboot fastboot, it will reboot into fastbootd and now can flash through fastboot.
Click to expand...
Click to collapse
i tried both qfil and fast boot same issue
Windows or Linux? If windows, look in Device manager when you do fastboot reboot fastboot and see if there is an exclamation in the list of devices, if so you will need to update the driver manually to android adb device (which is also the driver for fastboot). Which model do you own, Duel 2 or Pro 2? Have you tried Lenovo's RSA software tool since adb works? Use RSA only if it is a Duel 2, if it's a Pro 2 you will have to gather the right bundle posted on another thread (do not use it if you don't know as it can cause further issues).
kofijordan said:
i tried both qfil and fast boot same issue
Click to expand...
Click to collapse
Windows or Linux? If Windows, look in Device manager when you do fastboot reboot fastboot and see if there is an exclamation in the list of devices, if so you will need to update the driver manually to android adb device (which is also the driver for fastboot). Which model do you own, Duel 2 or Pro 2? Have you tried Lenovo's RSA software tool since adb works? Use RSA only if it is a Duel 2, if it's a Pro 2 you will have to gather the right bundle posted on another thread (do not use it if you don't know as it can cause further issues).