Related
Why does this do this?
I left it on charge over night last night, to my surprise - it hadn't charged...
I have read all over about this, but this is different...
I connected it again, and one blinking red light came up, not the triple you usually get if it's dead...
this is the only response, and is continuous.
it finally turned on, I checked the status after turning everything off and setting it to airplane mode. it was at 1%...
2 hours later it was still at 1%, and then after 10 minutes i checked and noticed it said 0%.. then died.
It's now still plugged in and is flashing one red light again.
Any ideas how to fix this?
Hi.
Have you taken the battery out?, if not do so for 10 seconds or more and pop it back in see what that does.
Happened to me once, no matter what I did it didn't charge do i took the phone to the service center, they messed with something on the upper side of the phone.. plugged it into the wall and booooooom ... started charging again..
When I asked him what he did, he told me " it just needs a little magic ! "
Sent from my X10i using XDA App
Haha cool
Yeah I'm gunna ring them up tomorrow, I tried that little trick but it didn't work.
It now shows no sign of life.
I'll let you know how it gets on.
hi
i had same problem last night but without putting phone to charge
when i put it in 2 diffrent charger i have red light same as usb cable
when i push power button same pb red light
hello
i find solution
we ahve to charge batterie with external charger about 2/3 hours and after put Xperia charger
solution tested 100% work fine
problem was battery was full empty
JoelMan1121 said:
Why does this do this?
I left it on charge over night last night, to my surprise - it hadn't charged...
I have read all over about this, but this is different...
I connected it again, and one blinking red light came up, not the triple you usually get if it's dead...
this is the only response, and is continuous.
it finally turned on, I checked the status after turning everything off and setting it to airplane mode. it was at 1%...
2 hours later it was still at 1%, and then after 10 minutes i checked and noticed it said 0%.. then died.
It's now still plugged in and is flashing one red light again.
Any ideas how to fix this?
Click to expand...
Click to collapse
Have you tried a different battery?
I don't know if we can fix this problem but as other posts above have said that mobile shops could be able to fix it.
You could be able to send it to SE but if your phone has been rooted or debranded you void the warranty.
i had the same problem last night, the battery died and then when i plugged it in it came on to charge, and then off again. after that point just blinking red light.
i removed the battery for some time, plugged it back in, and left it on charge for a bit and it came on.
i think the problem is, that when it starts charging, it wants to turn the screen on, which takes more power than the charger can give. so it goes into a loop. and dies.
but leaving it on charge helps (it worked for me)
I was reading a comic (Akira) and the prime's screen just went black... I just charged it last night and battery was well over 50% when it turned off. I tried the power button, power + volume down, power + volume up, power + up & down and also the reset button... nothing, not even a vibration or a polite F**k You across the screen. Any ideas?
Edit: So just got home and plugged it in - Viola, it kicked on for a second flashed the low battery symbol and is now charging. so it must be mis-reporting the battery level or something?
I have had this happen on a couple of occasions. The first time I did as you did and plugged it in to reboot. The other time I held the power button down for something like 10-30 seconds and it powered back up.
Same here. I had it yesterday.. hold the powerbutton for about 20 seconds and it will boot.
No idea why the Prime is having this behaviour. Happens to me once every 2 weeks.
yourprime said:
I've fallen and I can't get up!
Click to expand...
Click to collapse
Sent from my tablet thing with XDA Premium.
Same problem happened today - shut off
Hi
Just thought I'd add my comments as well.
Last night I fully recharged my Prime so keyboard and tablet were at 100% charge; this was completed about 6pm and I shut down the system for the whole night.
I then went out for the night.
Came to switch the unit on this morning, held the button for 2 secs and got the vibration you usually get, but system didn't switch on; screen stayed completely black, not even a feint black glow where you know the screen is black but its being powered...nothing.
Tried turning on again, with tablet attatched and detached..but still nothing, not even the vibrate.
Plugged the unit connected together into the mains and the charge lights came on...Orange...meaning charge was required. Triecswitching on and got the screen to disply the low battery charge graphic, then the screen turned off.
After 5 mins of charging, tried to start machine and it started fine.
Both batteries were dead though and needed charging. Its now been on charge for an hour and the tablet is charged to 33% and the keyboard is at 11%, so its looking ok on charging.
Thought it was a glitch, but looks like others are having similiar problems; just wanted to post my problem as well in case this becomes pandemic for Prime users.
Gaz
Hi there
I have used this tablet without bigger problems for months. a few days ago I've turned it on and after a few minutes using it the device froze completely. then the screen turned black after a few seconds, power led off. I've tried to reset it by pressing power button long and nothing happens, display black, led off.
Everytime I plug it in, the power led turns on, but nothing else happens.
Today I've opened the device and found out the batteries are at 2.8V. I've then charged them with my Lipo charger (had to desolder it, charge and then resolder). Still nothing works. And if there's no battery connected the exact same happens like with the batteries in place: nothing exept green led turns on.
So, why did this happen and how can it be fixed?
Thanks
same thing happened
hi,
exactly the same thing happened to me. Did you manage to solve the problem?
I also tried to empty the batteries and then to re-start, no success. The LED will light for a couple of minutes then turns off, but nothing else happens afterwards, the screen remains black all the time.
Resetting the device also doesn't work, the screen won't turn on, not even in the recovery mode.
I would appreciate any help on this issue.
ori
still dead
Nope, unfortunately I could never fix it so it's just laying around collecting dust as a expensive paperweight...
Anyone getting the sleep of death on their XTZ2? I'm running completely stock (not even rooted) on 23.0.1.A.4.30 and just experienced the unit not turning on at all until I do power + up volume.
Upon returning to life, the battery was 90%, so it wasn't battery.
Had a bit of a panic attack until I googled the solution (power + up) but this is the first time its happened to my unit, could it be related to the recent upgrade to 23.0.1.A.4.30? Anyone else seen this?
Mine lasted a day and a half after the 23.0.1.A.4.30 update and then became very erratic and kept forgetting wifi login info.
Did a restart and certainly got a sleep of death OK.
Would not switch on at all.
No power + vol up or attempt at repair via PC Companion made any difference to it.
Since gone back to Sony for repair, that was weeks ago, who knows if /when they will return it.
I had the same problem with mine as well I have the 561 the Verizon model. I have received a replacement but have not been able to get it to turn on either. It shows no signs off life at all not even when connected to power AC or PC. My old one would blink red and go dead when connected to a PC but this one doesn't even do that. I haven't had time to call for another replacement yet but really two defective devices in a row the second one didn't turn once.
Finally got mine back from Sony repair agent.
Worked fine for 3 days, then failed to power on again as per original fault.
Once again returned it for repair.
Think I'll give up and buy an iPad instead - at least they seem to be reliable and consistent.
This just happened to my tablet this morning. Tried all options under the sun but can't get it to boot.
I can't even do a factory reset and I don't particularly want to return it under warranty.... :'(
Mine is an xperia z2 tablet sgp561 (USA Verizon) build 17.1.D.0.437, stock 4.4.2. This issue happened to me 5 days ago after I powered off the tablet, it won't turn on again. Battery charge was ~70% at the time. Plugging it with factory Sony usb charger won't do anything, charging status LED remained Off, power button unresponsive. I let the tablet sit for 2 days without charging cable connected hoping the battery will drain completely by itself and the buggy firmware will restart executing at its base address getting out of the bug. Then I connected the crap to a fully charged 15000mah Anker power pack and alas, the charging status LED glowed red and after ~5 more minutes the LCD screen turned On for ~5 seconds showing a big battery icon at the center of the screen indicating 0% charge. Waited about 1 more hour and the charging status LED turned amber. This time I did the "power button + volume up" ritual holding both buttons for 10 sec+, expecting 3 vibrations but didn't feel any. At this point the tablet is still powered off. Because LED = amber, thinking battery must be at least 10% charged by now, just pressed the power button for ~2 sec and surprisingly the normal power On vibration came followed by Sony logo on LCD screen and the rest is normalcy.
From what I can remember, the recent change I made before this problem happened was turning Stamina to On in the battery settings (factory default is Off). I reset all settings back to factory defaults and so far so good.
Finally got mine back from Sony repair agent after about 3 week wait.
Seems to work OK now, fingers crossed it will keep working this time.
The note that came with the return indicated that they replaced the mainboard and battery, which is a better solution than their first attempt which was just to reflash the software.
wooly1 said:
Mine lasted a day and a half after the 23.0.1.A.4.30 update and then became very erratic and kept forgetting wifi login info.
Did a restart and certainly got a sleep of death OK.
Would not switch on at all.
No power + vol up or attempt at repair via PC Companion made any difference to it.
Since gone back to Sony for repair, that was weeks ago, who knows if /when they will return it.
Click to expand...
Click to collapse
Dude same thing, WTF is going on, I tried plugging it into charger, nothing. And once I got the msg of red colour battery icon and then I plugged it in. then it started charging and I was happy so I turned it on the it wasn't charging,
Please update me what happened and what they are saying cause I am about to send mine to get it fixed.
Edit: seems that by replacing the battery and mainboard has actually fixed the issue? Guess it's time to send it back to them, Gosh
c64rbr said:
Mine is an xperia z2 tablet sgp561 (USA Verizon) build 17.1.D.0.437, stock 4.4.2. This issue happened to me 5 days ago after I powered off the tablet, it won't turn on again. Battery charge was ~70% at the time. Plugging it with factory Sony usb charger won't do anything, charging status LED remained Off, power button unresponsive. I let the tablet sit for 2 days without charging cable connected hoping the battery will drain completely by itself and the buggy firmware will restart executing at its base address getting out of the bug. Then I connected the crap to a fully charged 15000mah Anker power pack and alas, the charging status LED glowed red and after ~5 more minutes the LCD screen turned On for ~5 seconds showing a big battery icon at the center of the screen indicating 0% charge. Waited about 1 more hour and the charging status LED turned amber. This time I did the "power button + volume up" ritual holding both buttons for 10 sec+, expecting 3 vibrations but didn't feel any. At this point the tablet is still powered off. Because LED = amber, thinking battery must be at least 10% charged by now, just pressed the power button for ~2 sec and surprisingly the normal power On vibration came followed by Sony logo on LCD screen and the rest is normalcy.
From what I can remember, the recent change I made before this problem happened was turning Stamina to On in the battery settings (factory default is Off). I reset all settings back to factory defaults and so far so good.
Click to expand...
Click to collapse
Did this method work for you? Plus did you come across like it was charging but it wasn't really charging,(like it showed the low battery stat with orange/red colour LED notification but suddenly it vanishes) then it's not responding at all.??
I had this issue 2 times with months in between , no response from power+vol up , no lights when charging , no response from pressing on the red button behind the flaps.
The last time it happened i tried putting it on the charger for a whole day with no result, then decided to let it rest a few days first , since someone had the same issue and it magically came back to life when he got back from a vacation.
So i try to turn it on 2 days later and the tablet to my surprise responds again with blinking red LED, recharching afterwards did the trick and worked again since
In my case i was running CM11 at the time, both times it happened after an update which required a reboot while, still mistified about the cause and the fix , i presume it solved itself by letting the battery drain.
Since then i reverted to stock rom just to be save but havent had it happen since, this also seems to have fixed some touchscreen problems i was having at times.
Hope this helps.
Bloody hell, I've just ordered mine today!
Don't stress. Mine got repaired. if it goes tits up that's what warranty is for
What did Fonebiz indicate was wrong with your Z2.?
They replaced the motherboard in mine.
Exactly the same, works fine now
This just happened to me today. So seems like overall suggestion is to try and let it discharge. The try to start it back up and charge it then. Just want to make sure that's the only potential solution now?
No! Leave it powered off, put in on a known good charger for at least 12 hrs. Don't touch it in that time.
If it does not come alive after that, send it in for repair.
ok..let me try that. I originally tried that and nothing occurred. However, I just found the OEM charger and usb cable and will try that. Unfortunately it's a Verizon version so sending it in will not be covered by Sony warranty. Per the Customer Service that I called.
ok..tried another charger and the red light came on, but it's been over 12 hours and still no go. I did notice that the red light was no longer on (from overnight charging). I left it unplugged for a bit and reconnected. The red light came back on but still no response. Sounds like i'll need to send in?
Looks like it.
Had the same problem on tuesday. Impossible to switch on, no light, none effect with charger, none effect when connected to PC/MAC etc...
After 4 days without charging my Z2, it came back to life, showing only a big red battery icon when pushing some seconds on the power button. Connected to a charger the red led indicator glowed ! (red battery icon is totally different with the original icon when tablet is charging in power off mode)
After a full battery charge with OEM charger and after a normal power on, my Z2 is now perfectly functionnal.
Hey, so, firstly I have a blue life one x. I love the phone and haven't had any problems until now.
I got an android update and my phone restarted, which has happened with the last two updates I got, so I didn't think anything of it. However, my phone was practically dead when this started and it restarted and got to the screen where it says "Android is starting... Optimizing application 1 of 143"
It would get to around 100 and turn off, restart and get to about 100 and turn off again.
I googled around and found a thing called bootloop. By what now seems to be a stroke of luck, my phone eventaully charged to about 40% and I got it to turn on and everything was fine but a few days ago, it died again and I ran into the same problem.
I went back to the boot loop instructions and tried it to no avail.
My phone has a fixed battery, so removing it wasn't an option. I left of the phone off the charger for 30 minutes and held the power button for two minutes(to discharge any remaining power?). Plugged it back in and it went right back to trying to boot back up and optimize apps.
I then removed the case, detached the ribbon that connects the battery to the board, held the power button for two minutes and let it sit for 3 hours. I connected the ribbon, plugged the charger back in and it instantly tried to boot up back into the optimizing screen and turned off.
I did all this again but left it for the past two days and now its back to rebooting over and over...
Things of note:
The light indicator turns red when the phone is connected to a charger, whether the battery ribbon is connected or not.
When it displays the blu splash screen, the optimizing applications screen, or recovery mode, the light indicator is off.
I can get into recovery mode, but I can't do anything before the phone turns off and reboots again.
Any help would be appreciated!