I Have decided that this thread has served it's purpose and will now be closed to future posts. Please direct and 'non' SHV-E160L post's to
Brixfix V2
Please can all Ongoing jobs/works migrate to the above thread.
-----------Final Notes--------------
It has been mentioned many times that i should go back and correct the information below, i started to correct a few post's then realized i was removing the flavour in change of colour and size, parts of this thread documents my mistakes, assumptions and general lack of understanding of how we NOOBS post on XDA, It's with that in mind that i have decided to leave the mistakes in, so you can see in writing what i gained from the support of other Devs here.
Now, if you are NOOB in anyway or have a few questions please click HELP
If you are bricked and need help, read this thread first, there is NO one CLICK solution for anything, even this mentioned device.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
So you Brixed/bricced/BOD/QDL/EDLOAD/QHS-USB/05c6:9008/05c6:9025/ your device? Need a Oil and brush , Need help, follow this
One, Rules
Two, Understanding
--------------------------------------------------------------------------
Tip From the Author,
Some of you may have noticed that i did not start the original thread with a question, I did something my mentor taught me at around 9 years old but didn't put into good use until much later in life.
The tip is write things down as a question for yourself, in the writing process you get to pass the information past the part of your brain that interprets information, virtual sounding board, before posting as a question for others.
--------------------------------------------------------------------------
New Tools for debricking, goto
Brixfix V2
---------------------------Further Info Info -----------------------------
** I have Since Fixed the device and developed soultions for non shv-e160l devices. Prior posts are undergoing edit's for corrections.
** if you want the glory shot, sorry you will just have to read through.
** If you are selling this as a solution, dont. I know who you are.
---------------------------Original Post-----------------------------
Hi All
As i mentioned on this thread http://forum.xda-developers.com/showthread.php?p=32231827#post32231827 i will be attempting to come up with a home grown debrick solution for a SHV-E160L samsung note from korea.
I will use the forum to document what i am doing, i am very new to this so correct me please if i am wrong. I have never done Android dev work at any time but i have a very good understanding of the logic behind it all. `
Things i Have :-
Phone ( SHV-E160L)
bus pirate v3 with jtag firmware
openocd compiled on ubuntu and centos 6
smd jtag adapter and relay wire ( magnetic wire)
things i still need :-
openocd target config file for MSM8660 Snapdragon cpu (and a better understanding of eMMC access, how to load boot loaders either into ram or eMMC or trigger fail over boot to sc-card, USB via software or X0M/Boot pins)
assembled jtag (it's the smallest soldering i've ever seen)
.PIT file for 32GB model (if someone could pull the .PIT file from a working unit I would be happy, specify your radio/kernel versions when uploading)
micro fine solder iron tip and 20w iron (i've got 60w but too high for this type of work)
Does anyone have a idea of the SD-CARD partition layout, files for snapdragon devices, google has given me much for other devices but not a snapdragon .
Another question, I've used the USB jig to trigger 301K mode USB-Factory and seen no activity in dmesg for usb devices, i've yet to try windows, does windows/linux behave in a different way when it comes to usb , as in windows see's the qualcom usb mode but not linux ? does the usb client device always start the comms?
using the 615K usb jig i get nothing too, no pbl message from samsung (hence i am led to think is's the pbl/sbl thats damaged)
My understanding up boot is as follows
iROM code
This loads basic settings to boot the PBL (iROM is in rom) the PBL is loaded into radio(modem) cpu and then loads the SBL(s)
PBL/SBL stored in eMMC at address ????? (need to document the address for the masked access to eMMC and jtag/openocd access unmasked access)
Once the SBL is loaded you with have the ODIN mode (USB/UART)
from what i can see of commercial JTAG boxes is the access the radio cpu via jtag, write a new PBL/SBL to the eMMC then halt/reset cpu which now loads the new bootloaders, (resurrect dead body)
The openocd TAP id for the cpu should be 0x105310E1 but thats a number i got from a riff box log, not any actual testing ( still need to solder the fine pitch connector)
Here is a log from a riff box, not sure if the address's are usable accross to opencd
Taken from gsm-forums:-
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung E160K V1.0.4535.7001]
Connecting to the dead body...OK
Detected dead body ID: 0x105310E1 - IGNORED!
Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0000 (KTS00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0000 (KTS00M, 0x000000200000 Bytes = 2.00 MB)
Flashing the dead body...OK
Resurrection complete!
Click to expand...
Click to collapse
I did notice one thing, the riff box opens the serial port, i wonder if they load PBL+SBL into memory, reset the cpu, then using the serial connection activate download mode ? (like on the captive)
I also dont know how the cpu (jtag TAP id? ) and flash variables translate accross to openocd as ive not found a target config file yet ( or my searching is wrong)
in the full stock Firmware I was able to extract the .tar file which contained,
Code:
amss.bin <-- application cpu boot files ?
boot.img <-- kernel/initrd ramdrive
mdm.bin <-- modem cpu boot files
recovery.img <--- recovery image
system.img.ext4 <---- rest of the system applications
so i think we have the two cpu firmware/boot loaders in the .bin files, these bin files are just fat32 images, to access in ubuntu use
Code:
mount -o loop mdm.bin /mnt/mdmmountlocation
My guess is my first approach is getting the right PBL/SBL into the system and getting some feed back via uart, i have the jtag pinouts and further reserach says there is a UART2 on the jtag header, so when soldering up my jtag adapter i will include all pins if i can and sniff for serial logic, i happen to have a Open source logic sniffer, great tool as i do a lot of hacking into serial devices like scales and till printers .
back to topic.
When i do get to the jtag part at a minimum i should have access to the modem radio, afaik jtag devices connect in chains and most of the IC's that have jtag on the phones board all should link to the master device (i am thinking it's the modem cpu, no application) and that the Two cpu's share the eMMC memory some how, or it could be one cpu loads it into the other (it is connected via jtag down the chain) .
hopefully someone could correct me there.
Most of this is theory and my guess work, correct me if you find a mistake. most of the research is only over a few days too so i am far from finished there, does not help that most of the users speak a language that google translate just does not have a flair for.
Most of the info seems to suggest the modem cpu is the first inline so i decided to look further into the files there, notice the mdm.bin file is 23Mb, thats large, when mounted i notice the is a folder called 'image' ( amms.bin has folder called IMAGE , note the case difference, dont yet know whay)
in image folder we have :-
Code:
1.3M Sep 30 13:07 AMSS.MBN
35K Sep 30 13:07 DBL.MBN
2.2M Sep 30 13:07 DSP1.MBN
19M Sep 30 13:07 DSP2.MBN
40 Sep 30 13:07 EFS1.MBN
40 Sep 30 13:07 EFS2.MBN
40 Sep 30 13:07 EFS3.MBN
295K Sep 30 13:07 OSBL.MBN
Ah, i see amss.mbm , that must be the boot loader for the application cpu, DBL.MBM seems to be the PBL , OSBL.MBM could be the SBL
then there is the DSP/EFS files, I did do the command strings on all the files,
DBL.MBM does not have any text in the file that points to being able to do UART on boot, all text seems internal like pointers and references to the original build files e.g
Code:
D:\Q1LGT_MDM\MDM9600\modem_proc\core\boot\secboot2\dbl\target\mdm9x00\src\dbl_ddr.c
9x00B-SCAQSVZM-31613102
D:\Q1LGT_MDM\MDM9600\modem_proc\core\boot\secboot2\dbl\target\mdm9x00\src\dbl_sahara.c
but it also does contain data like this
Code:
auth_image
@[email protected]
@configure_hw
@flash_init
l0:eek:SBL
load_osbl_img
@DBL, Start
hw_init
so it looks more likley that dbl is first in the chain, it refers to loading osbl and configure hardware, i wonder if it means USB/UART at this stage or setting up ram and other GPIO's
in OSBL.MBM we have more interesting text
Code:
MbP?
Unable to attached to ChipInfo DAL
SAMSUNG
TOSHIBA
Flash: Failed to do initialization for probe!
ONFIx
0:ALL
Flash: Multi 2X page read not supported!
Flash: Multi 2X page write not supported!
boot_qdsps
OSBL
hw_init
hw_init_secondary
OSBL, Start
create_vector_table
ram_init
retrieve_shared
clobber_add_protection
mmu_flush_cache
OSBL, End
OSBL, Delta
osbl_sahara_load_amss
osbl_sahara_load_dsp1
osbl_sahara_load_dsp2
osbl_sahara_load_ramfs1
osbl_sahara_load_ramfs2
osbl_sahara_load_ramfs3
smem_boot_init
so it is looking more and more like DBL then SBL which then loads all of the other parts , also if you notice EFS1/2/3 are all tiny 40byte files, now i see why, they are loaded as ram-drives, so i assume those file set out the basic EFS file system in the ram.
again from research the boot stages are often counted as 3, i am assuming the real first part is in rom of the cpu (is this what triggers the qualcom download mode ) that loads DBL from eMMC and chain loads SBL
Now looking around the riff forums i see the list the info in a different way
Code:
Partition 0
SBL1
SBL2
Partition 1
RPM
SBL3
eMMC APPSBoot
TZ
.PIT
Click to expand...
Click to collapse
TZ i think is Trusted Zone
RPM - Power manager ?
now how this translates to file name from full flash and to mmcblk0p1 partitions i have yet to find out, i still dont have a .PIT file from a 32gb model
More updates to come,
regards
DarkSpr1te
CPU Boot order updates
So my digging has taken me back round to some of me early searching which i forgot about , hardware level seems to support the qualcom usb mode, but it can be disabled by manufacturer, so even if you find a resistor to the BOOT_CONFIG GPIO and ground it , it still may not work, and you could toast your board. once the qfuse is gone for that track, the maker can now use the gpio for anything else, it no longer controls the iROM branch choice ( CPU:do i start usb first or last?), it my thinking that on the first board sent out by the designers for a final production run ( those first public devices) they keep the option open to print off DEV models by changing the resistors/value of while the hardware stays same, not to be confused with dev board, that is pin/track simlar but is used to design the software mainly, sometimes hardware debug but as you change the hardware between the dev platform and production this is less helpful, google new.intrinsyc.com and apq8060, they produce a dev board that is the same as the device we hold, but everything is broken out for testing so don't expect to see this left in a bar for you to e-bay.
EDIT:
Above I refer to a dev phone and dev board, these are SURF and FFA, FFA is form factor accurate and SURF is Subscriber Unit Reference.
Here is the link, http://forum.xda-developers.com/showthread.php?t=1856327
Now from what i see, it's the same(edit:simlar) X0M pin setup as other phones, ground the right pin, reverse boot order, but this maybe two pins in the snapdragon,
[copied from other link]
Simplified table:
Code:
------------------------------------------------------------------
BC[5:0] Mapping
------------------------------------------------------------------
0b00000 Emergency Boot from SDC3 (SD) followed by USB-HS
0b00001 SDC3 followed by SDC1 (eMMC)
0b00010 SDC3 followed by SDC2 (if used)
0b00011 SDC1 (eMMC)
Click to expand...
Click to collapse
So if 0b00000 is EM boot and the docs say the the two gpio's that control this (if qfuse not blown) are taken high then it's 0b00011, so grounding those two resistors should give us 0b00000 or EM boot, the cpu docs also say they are internally grounded, the schematic says the voltage goes throught a 10k resistor, so grounding that side of the resistor that 'goes' to the cpu should change the boot order, but before trying this out, remember if you get the live side of the resistor the is no resistor between your probe and ground, that full current, short, blown, no more johnny 5.
Have you managed to unbrick the E160L?
darkspr1te said:
So my digging has taken me back round to some of me early searching which i forgot about , hardware level seems to support the qualcom usb mode, but it can be disabled by manufacturer, so even if you find a resistor to the BOOT_CONFIG GPIO and ground it , it still may not work, and you could toast your board. once the qfuse is gone for that track, the maker can now use the gpio for anything else, it no longer controls the iROM branch choice ( CPU:do i start usb first or last?), it my thinking that on the first board sent out by the designers for a final production run ( those first public devices) they keep the option open to print off DEV models by changing the resistors/value of while the hardware stays same, not to be confused with dev board, that is pin/track simlar but is used to design the software mainly, sometimes hardware debug but as you change the hardware between the dev platform and production this is less helpful, google new.intrinsyc.com and apq8060, they produce a dev board that is the same as the device we hold, but everything is broken out for testing so don't expect to see this left in a bar for you to e-bay.
Here is the link, http://forum.xda-developers.com/showthread.php?t=1856327
Now from what i see, it's the same(edit:simlar) X0M pin setup as other phones, ground the right pin, reverse boot order, but this maybe two pins in the snapdragon,
[copied from other link]
Simplified table:
Code:
------------------------------------------------------------------
BC[5:0] Mapping
------------------------------------------------------------------
0b00000 Emergency Boot from SDC3 (SD) followed by USB-HS
0b00001 SDC3 followed by SDC1 (eMMC)
0b00010 SDC3 followed by SDC2 (if used)
0b00011 SDC1 (eMMC)
So if 0b00000 is EM boot and the docs say the the two gpio's that control this (if qfuse not blown) are taken high then it's 0b00011, so grounding those two resistors should give us 0b00000 or EM boot, the cpu docs also say they are internally grounded, the schematic says the voltage goes throught a 10k resistor, so grounding that side of the resistor that 'goes' to the cpu should change the boot order, but before trying this out, remember if you get the live side of the resistor the is no resistor between your probe and ground, that full current, short, blown, no more johnny 5.
Click to expand...
Click to collapse
I think my E160L got a real brick today after I tried to flash a modified Rom downloaded from a Chinese forum. It can not be powered on after rebooting (installed successfully). I desperately need advice now on how to deal with it.
Jeff_GTA said:
I think my E160L got a real brick today after I tried to flash a modified Rom downloaded from a Chinese forum. It can not be powered on after rebooting (installed successfully). I desperately need advice now on how to deal with it.
Click to expand...
Click to collapse
Do you have any backups like nandroid ? does the 3 button boot still work ?
Regards
Have you looked into using ort-jtag. It's only about $150 (USD).
I've been looking into this myself for low-level debugging/bootloader development on SGH-T959V and SGH-I717.
All three of these devices are supported by ort-jtag and have header connectors for the jtag pins.
So I'm also getting some of these from digi-key, and making a small receptacle, much like in AdamOutler's captivate bootloader development thread. (search for k-ww)
Again, ort-jtag does support the SHV-E160L. (search that link for SHV-E160L)
PBL Dump - I think
So ive been doing some tests.
I think i managed to dump the PBL
i dumped memory and a strings search return this
Code:
pbl_error_handler.c
pbl_flash_nand.c
pbl_flash.c
dload.c
pbl_flash_nand.c
pbl_flash_onenand.c
pbl_auth\secboot_rsa_math.c
pbl_error_handler.c
pbl_auth.c
pbl_auth.c
pbl_auth.c
pbl_auth.c
pbl_auth.c
pbl_mc.c
pbl_mc.c
pbl_error_handler.c
and
Code:
qhsusb\src\dci\qhsusb_dci.c
}^PBL_DloadVER1.0
!8}^
}]^}^
Q`omm
z8}]
DEBUG
SW_ID
OEM_ID
pbl_flash_onfi.c
pbl_flash_nand.c
pbl_flash_sflashc.c
pbl_loader.c
pbl_flash_sdcc.c
pbl_auth.c
pbl_auth\secboot.c
pbl_auth\secboot_x509.c
QUALCOMM COPYRIGHT 2009BOOT ROM VERSION: 1.4QHSUSB VERSION: 00.00.08
BOOT ROM AUTHOR: DHAVAL PATEL
07 0000 SHA1
does any one want the dump that can reverse it ?
Dumps & execute address
I also need the help of other SHV-E160? owners, i need dumps from working phones, i managed to create a 8660_msimage.mbn and flashed it, but i was using i717 bootloaders and i dont think they will work, i need working dumps from working phones, starting with partition table layout, sbl1.mbn and sbl2.mbn
Does anyone know if the is is correct
SBL1 exec address 0x2A000000
SBL2 exec address 0x2E000000
as i can upload the sbl to 0x2a000000 but not the sbl2 to 0x2e000000
i can also upload the tz.mbn to 0x2a020000
i am trying to use sec boot 3 based call stack but am unsure of the real exec values
Ive seen in another post these values
"
It looks like ours deviates slightly from this.
If the headers are to be believed,
TZ is loaded at 0x2A000000
SBL3 is loaded at 0x8FF00000
APPSBL/aboot is loaded at 0x88E00000
"
the post is
http://forum.xda-developers.com/showpost.php?p=30057296&postcount=243
it does explain why i cant load into 0x2e000000
Progress
So today i made real progress, I have been able to flash a basic program to allow me to access the EMMC, i have taken a full backup and now i need to start scanning the dump for need information,
I still need help from other users so please if you are will to provide me dumps of your working device that would help me a great deal
So Part One is a sucess, I have been able to flash my own code and power on the galaxy note. next step is rebuilding the emmc partition tables, testdisk can find the partitions but is not alowing me to write a non standard partition table (which emmc seems to be formatted with)
Thanks
darkspr1te
help QPST Software Download
Hi,
I'm stuck with the same problem can you tell me what image you use to the phone. I stuck here. I' m really don't know what to do?
Thank you for your help.
tyllerdurdent said:
Hi,
I'm stuck with the same problem can you tell me what image you use to the phone. I stuck here. I' m really don't know what to do?
Thank you for your help.
Click to expand...
Click to collapse
First thing i must say is dont flash your phone just yet!! walking blindly into this could render your phone useless due to certain data being lost for good.
if you still wish to continue i will upload a basic guide and files. My method is still in development, it has many bugs ( i flashed the phone with i717 roms, working, SHV-E120 roms, working, N7000 rom complete fail)
But first some questions,
Which model phone is it?
what happened to get you to the point of needing the flash ? ( i ask so i can trace why the bricks are happening and hopefully fix it)
thank you for your help, I will be waiting your method and your files.
Thank you so much for your help.
My phone is a samsung galaxy note SHV-E160L korean version.
what happen was:
I tried to upgrade the firmware with kies and suddenly the program crash. My phone enter in an error issue with the firmware and said use emergency recovery mode.
I tried the recovery several times (uninstalling kies and install it again but that never work).
So, I download odin and this files to restore the original firmware:
CSC - GT-N7000-MULTI-CSC-OZSLPF.tar.md5
Phone - MODEM_N7000XXLR1_REV_05_CL1144476.tar.md5
Bootloader- N7000_APBOOT_N7000ZSLPF_CL558430_REV02_user_low_sh ip.tar.md5
PDA - N7000_CODE_N7000ZSLPF_CL558430_REV02_user_low_ship .tar.md5
Pit for 16GB - Q1_20110914_16GB.pit
I connect my phone and try to install the firmware again, but odin fail and my samsung became a nice brick.
The phone currently does not turn on, the phone is in download mode and I install QPST and the program recognize the system in download mode.
I want to try your method because other information I collected said that I have to send it to guarantee.
Can I install i717 rom in the E160L?
I will be waiting for your post because sincerely I don't know how to repair it.
Thank you so much.
Hello darkspr1te
First of all, nice work there (though I didn't understood most of the things there, but seems there is some good work going on on our SHV-E160's
On your comment;
( i flashed the phone with i717 roms, working, SHV-E120 roms, working, N7000 rom complete fail)
Does that mean that i717 roms can work on the SHV-E160 devices? Please share if that is the case.
The geeky bits
tyllerdurdent said:
Thank you so much for your help.
My phone is a samsung galaxy note SHV-E160L korean version.
what happen was:
I tried to upgrade the firmware with kies and suddenly the program crash. My phone enter in an error issue with the firmware and said use emergency recovery mode.
I tried the recovery several times (uninstalling kies and install it again but that never work).
So, I download odin and this files to restore the original firmware:
CSC - GT-N7000-MULTI-CSC-OZSLPF.tar.md5
Phone - MODEM_N7000XXLR1_REV_05_CL1144476.tar.md5
Bootloader- N7000_APBOOT_N7000ZSLPF_CL558430_REV02_user_low_sh ip.tar.md5
PDA - N7000_CODE_N7000ZSLPF_CL558430_REV02_user_low_ship .tar.md5
Pit for 16GB - Q1_20110914_16GB.pit
I connect my phone and try to install the firmware again, but odin fail and my samsung became a nice brick.
The phone currently does not turn on, the phone is in download mode and I install QPST and the program recognize the system in download mode.
I want to try your method because other information I collected said that I have to send it to guarantee.
Can I install i717 rom in the E160L?
I will be waiting for your post because sincerely I don't know how to repair it.
Thank you so much.
Click to expand...
Click to collapse
Ok, as i said it's still a work in progress at the moment.
I used the i717 bootloaders (thats why we have a brick as it's not getting to the aboot loader or little kernel as some other refer to it) and E160 modem and application cpu as my first target is getting odin mode back.
I was able to also use the E120 bootloaders (screen was messed up though )
I've just got home from a very long shift so i will do a full and clear write up ( STILL a work in progress ) tomorrow (20th)
but i will explain the basic now as you do need to download large files before we continue.
First you need to download the same firmware as you were originally on before the brick, The reason is because between versions i suspect there is minor changes in partition tables (that why the n7000 roms brick )
If you dont have the latest QPST (2.7.3xx or higher ) please google for it now, there are many sites that offer it. (links will folllow tomorrow)
also down load :-
ABOOT_SGH-I717M_I717MUGLA2_user_CL875155_REV00.tar (or tar.md5 )
i717-GB-Modem.tar (or .md5)
now my initital work was based off a chinese link for the A820L
http://blog.csdn.net/su_ky/article/details/7773273
To save you the time of many hours of translation and cross reference here is the quick run down
When the phone is in QDLoad mode its because the PBL (Stored in ROM , read only memory) could not start SBL1 or SBL2 , it stores the error in IRAM location 0x3FF18 and then goes to QDLoad fail mode. At this point it has tried uart, sd-card before hand and those failed too.
IRAM is the small built in memory of the MSM8660 CPU, it has not initiated the main SYSTEM ram yet so our memory space ro running code is 87k and 256k (refer to document 8960_boot_architecture.pdf found the unlock bootloaders section.
Now because our partition table and or our bootloaders are damaged (or we have emmc brick bug) we have to rewrite that data again to revive our bricks.
This is where it gets hard, and where my warnings now come into play.
right now you must think of the EMMC chip (its the name for the internal SD-CARD we boot from and store our normal data, imei and all the other data of the system, it is just a sc-card with better security for our purpose)
This emmc chip holds all of you settings for phone function and we must not loose that,
But...
we have to write data to the chip to boot again, I am not fully aware of all the memory locations so this is assumptions on my part.
we are going to write a basic bootloader that turns the whole phone into a sd-card, then write new bootloaders
using QPST we upload 8660_msimage.mbn (its a out of the box emmc factory image) this file is ment for setting up of dev versions of the phone, it made up of the following parts
sector 0 partition table or (partition0.bin AFTER patching with info from patch0.xml) I do not have a real copy of the original of this, it can be pulled from a working SVH-E160x using the code at the end.
after the MBR (which is the first part of the partiton make up, EBR follows, we can have 3 primary partitions and the fourth is a extended which is just another partiton table pointing to the next EBR and so on, upto 29 parititons i think)
anyway, after the MBR is SBL1, which chainloads SBL2 then that side loads RPM, gets a go signal then loads SBL3, when SBL3 is done most of the device hardware has been mapped into the cpu's memory table, SDRAM is now ready for larger code,
aboot now loads
some of the above loading functions occur at the same time and some wait on go signals from other code in other CPU's and some fail due corruption and or security check fails( JTAG users can watch the memory as it changes and halt, change data and continue which is why JTAGers's have more power , we dont have loader outputting data yet so no feed back, hence the brick)
when aboot is loaded we now have access to odin, so thats the goal, get aboot loaded for now who cares about the rest of the funtions.
we do need to care about those function later so thats why we will backup the entire system, i dont know if this will really work when restored and bring back all of our settings, thats later,
So onto the writing and possibly overwriting of important information, WARNING, i dont know yet if we are overwriting imei or simalr data yet so proceed at your own risk.
We will get the required from factory (qualcomm test or dev board not samsung factory in the box for consumer) from the MUI phone firmware
http://bigota.d.miui.com/QDN43/Mioneplus_QDN43_fastboot_Android_4.0_d3d83nmdk2.zip
from this zip we want 8660_msimage.mbn, patch0.xml, partition0.bin MPRG8660.hex ( this file is uploaded first, its a serial bootloader that is loaded at 0x2a000000 (start of PBL IRAM space 256k in size) and that setups a emmc to command access (we use revskill to upload the same file and dump memory , sadly ive not found a way of pulling the entire emmc to a backup, if we can figure that out we can pull the entire boot chain, fix it and send it back with what ever versions we desire, for now revskill is used to read the PBL error so we can at least see why we cant boot, not quite jtag but best we got ))
so now we have a phone running a basic bit of code that allows us to use code sent to serial port to write (possibly read) the emmc
we then use QPST to write the 8660_msimage.mbn as a one to one copy to the very start of the emmc , reboot phone and then when the phone restarts, it sets up the ram, some hardware (charging system, you will now notice your phone gets warmer that before when plugged in) and gives us direct access to the emmc as if it was a sd-card
at this point you could move the phone to any pc and it's just a sd-card branded qualcomm
BUT at this point the pc or any other computer you connect it too only see's the partition table contained in the 8660_msimage.mbn file , you other data is there so i advise the next step you MUST do.
connect the phone to a linux computer (use a live cd or live usb if you are not a normal linux user)
you will then run the following command
Code:
dd if=/dev/sd? of=/mount/location/shv-e160-full-emmc.bin bs=512
? is the letter of the drive , use dmesg and look for sdb or sdc , if you dont understand this part then i would suggest waiting for a possible script/one click solution. right now i am still booting only 1 in 20 boots and do not yet know why the boots fail and why some work.
of=/mount... this is where you will place the entire 16GB (32GB for 32gb models ) which should be a one to one copy of the system
the bs=512 is very important, it's block size, again, if you dont understand then maybe wait.
Thats enough for now, i am going to spend a hour or two working on some theories i came up with today.
user with working phones, please google how to backup parts of your phone, this may happen to you so it's best to backup asap !!!
from the blog.csd site a script to grab the partition table data, if a working usr could please run this and post the file, it does not contain user data only the partiton table and a direct 1 to 1 restore for any phone, i think it possible to write that direct back to a QDLoad mode phone, re write the bootloaders from linux and bingo working phone. i dont have backups as it's not my phone, it belongs to a client who knows i like to tinker with electronics.
anyway, once i have the partition file i can overlay it on my test phone (which i can activate QSLoad at any time, hence it's unbrick-able dev mode)
once the partition file is written to my phone, i can build a script to backup your important data, write known working bootloaders, and reboot the phone into a usable device.
here is the script in python (user linux live cd with a copy of adb, just google adb linux pack, there is a windows and linux allin one pack)
or you can get the original from the link above, i've not tested this as i dont have a device in adb mode but i've read through it and it looks sound but never tested by me.
Well i hope that enlightens you, am sorry i dont have a all in one solution for you, it's still a dev project and most of the information i have has only been collected over the past week, i only discovered it's QSDload after getting a msm8660 schematic and i still dont know what i am trully shorting out to trigger the QSDload when ever i want, even when it's booted
If any one from the unbrickable project(s) want to get in touch to share info i would be happy, i am also sure this is a usable solution for HTC phones as well
oh and one last thing
i read only a hour ago (via cell phone while in a car so not 100%) that once the phone is in QSDload and stays in QSDload on every power cycle then we can write the partition table to a SD-CARD and it will boot that, i have not tested that yet, i will try and see if the 8660_msimage.mbn file written to a sd-card works
I also suspect that some of my good boots have been when i've mixed up the sdcard with system.img.ext4 etc on it with the one with just update.zip on it. it's one my list of things to check , any suggestions are welcome as to how i correctly format the card (heads,cylinders, block size etc)
ok folks, hope this helps
COPY TEXT BELOW ONLY INTO A FILE AND RUN WITH PYTHON (linux is easier, may be possible to use a vm box, i am but linux is my main os and windows is the vm)
Code:
import os
from struct import *
def mbr():
global offset, partitions
os.popen("adb shell su -c 'dd if=/dev/block/mmcblk0 of=/cache/partition0.bin bs=512 count=1'").close()
os.popen("adb shell su -c 'cp /cache/partition0.bin /sdcard/partition0.bin'").close()
os.popen("adb pull /sdcard/partition0.bin .").close()
f = open("partition0.bin", 'rb')
data = f.read()
f.close()
partitions = [ ]
n=0
while True:
buf = data[446+(16*n):446+(16*(n+1))]
partition = dict(zip(('boot', 'id', 'start', 'size'), unpack('4I', buf)))
partition['type'] = "MBR"
n += 1
partition['no'] = n
partitions.append(partition)
if partition['id'] == 5:
offset = partition['start']
break
def ebr():
global offset, partitions
n = 0
while True:
a = 0
os.popen("adb shell su -c 'dd if=/dev/block/mmcblk0 of=/cache/ebr bs=512 count=1 skip=" + str(offset+n) + "\'").close()
n += 1
os.popen("adb shell su -c 'dd if=/cache/ebr of=/cache/partition0.bin bs=512 count=1 seek=" + str(n) + "'").close()
os.popen("adb shell su -c 'cp /cache/ebr /sdcard/partition0.bin'").close()
os.popen("adb pull /sdcard/partition0.bin .").close()
f = open("partition0.bin", 'rb')
data = f.read()
f.close()
while True:
buf = data[446+16*a:446+16*(a+1)]
partition = dict(zip(('boot', 'id', 'start', 'size'), unpack('4I', buf)))
if partition['id'] == 5:
break
if partition['id'] == 0:
return
partition['type'] = "EBR"
partition['no'] = n
partition['start'] += n-1+offset
partitions.append(partition)
a += 1
if __name__ == "__main__":
mbr()
ebr()
os.popen("adb shell su -c 'cp /cache/partition0.bin /sdcard/partition0.bin'").close()
os.popen("adb pull /sdcard/partition0.bin .").close()
for part in partitions:
print "%s %2i, Boot: 0x%02X, Id: 0x%02X, Start: 0x%08X (%8i), Size: 0x%08X (%8i, %8i KB)" % (part['type'], part['no'], part['boot'],part['id'], part['start'], part['start'], part['size'], part['size'], part['size']/2)
Click to expand...
Click to collapse
beginning
thank you for your help,
I currently have the qpst version 2.7 build 373. You think is enough of download the same version of Chinese post QPST.2.7.374.rar
I will begin to download the other files required and I will be commenting my progress.
Thank you so much for your help, i really appreciate that you share you r knowledge.
Requests
While i try some theories if othe users could possibly provide me with :-
Original partition table via script above and also via adb
use
adb and run
Code:
cat /proc/partitions > /sdcard/partitions.txt
fdisk -l /dev/block/mmcblk0 > /sdcard/fdisklist.txt
mount > /sdcard/mountlist.txt
Then on the pc side using ADB again do the following
Code:
adb pull /sdcard/partitions.txt
adb pull /sdcard/fdisklist.txt
adb pull /sdcard/mountlist.txt
and post those files.
there are many posts on it so wont repeat but later will add a link.
along with some spell checks :laugh:
if you can dump the boot loaders from a original e160x too as my data started currupt.
i also need to talk to someone who can assist me in writing a program to take the pit file and turn it into this
Code:
<?xml version="1.0" ?>
<data>
<!--NOTE: Sector size is 512bytes-->
<program file_sector_offset="0" filename="" label="SMD_HDR" num_partition_sectors="65536" physical_partition_number="0" size_in_KB="32768.0" start_sector="1"/>
<program file_sector_offset="0" filename="sbl1.mbn" label="SBL1" num_partition_sectors="1000" physical_partition_number="0" size_in_KB="500.0" start_sector="65537"/>
<program file_sector_offset="0" filename="sbl2.mbn" label="SBL2" num_partition_sectors="3000" physical_partition_number="0" size_in_KB="1500.0" start_sector="66537"/>
<program file_sector_offset="0" filename="rpm.mbn" label="RPM" num_partition_sectors="1000" physical_partition_number="0" size_in_KB="500.0" start_sector="69559"/>
<program file_sector_offset="0" filename="sbl3.mbn" label="SBL3" num_partition_sectors="4096" physical_partition_number="0" size_in_KB="2048.0" start_sector="70559"/>
<program file_sector_offset="0" filename="aboot.mbn" label="ABOOT" num_partition_sectors="5000" physical_partition_number="0" size_in_KB="2500.0" start_sector="74655"/>
<program file_sector_offset="0" filename="" label="BOOT" num_partition_sectors="20480" physical_partition_number="0" size_in_KB="10240.0" start_sector="79655"/>
<program file_sector_offset="0" filename="tz.mbn" label="TZ" num_partition_sectors="1000" physical_partition_number="0" size_in_KB="500.0" start_sector="100135"/>
<program file_sector_offset="0" filename="partition0.bin" label="MBR" num_partition_sectors="1" physical_partition_number="0" size_in_KB="0.5" start_sector="0"/>
<program file_sector_offset="1" filename="partition0.bin" label="EXT" num_partition_sectors="22" physical_partition_number="0" size_in_KB="11.0" start_sector="69537"/>
</data>
Click to expand...
Click to collapse
*edit
the partiton0.bin provided below is 8.5kb (.5kb MBR, 8kb EBR) and in raw_program0.xml bove it say 0.5kb and 11kb, making that file 11.5kb, i dont know if the A810 has larger or smaller EBR than us, it could be they pulled extra, in my reading of the dumps i've seen lots of padded 0's after files (between sbl2/ebr/rpm) anyway if you just copy paste it will throw a error, ive got it set at 0.5 and 8.
EDIT:- Do not use this file, ive uploaded newer files later on.
some of the questions i need to answer are :-
1. what is the first partition, it's dos, around 105mb and labled smd_hdr and is filled with smd_hdr.bin (or mbn)
2. what are the real sector locations of the files, above you will see the rawpartiton0.xml file, this tells QPST where in the emmc to put the data num_partiton_sectors does match data from the pit files, but i dont know the real offsets yet, (samsung or htc could put the rest of the partiton table in cpu qfuse data areas and not write it to the emmc to confuse us and write the real files to another location and use the pit file as a base+offset calculation)
start_sector is the real location on the emmc, where it starts writing the file.
at the end is partiton locations(its a generic file containing the first few byes of default partition table, patch0.xml then updates this data), i dont have our device specific figures yet, i also dont fully understand patch0.xml and the difference in figures used.
if we have a backup of each of the different version of android partitons we could just write that in replacement of partiton0.bin and we dont need patch0.xml, this file sole job to alter the generic files, oem's have the choice of changing this data.
Code:
<?xml version="1.0" ?>
<patches>
<!--NOTE: This is an ** Autogenerated file **-->
<!--NOTE: Patching is in little endian format, i.e. 0xAABBCCDD will look like DD CC BB AA in the file or on disk-->
<!--NOTE: This file is used by Trace32 - So make sure to add decimals, i.e. 0x10-10=0, *but* 0x10-10.=6.-->
<patch byte_offset="506" filename="partition0.bin" physical_partition_number="0" size_in_bytes="4" start_sector="0" value="NUM_DISK_SECTORS-208801." what="Update MBR with the length of the EXT Partition."/>
<patch byte_offset="506" filename="DISK" physical_partition_number="0" size_in_bytes="4" start_sector="0" value="NUM_DISK_SECTORS-208801." what="Update MBR with the length of the EXT Partition."/>
<patch byte_offset="458" filename="partition0.bin" physical_partition_number="0" size_in_bytes="4" start_sector="16" value="NUM_DISK_SECTORS-1695744." what="Update final partition with actual size."/>
<patch byte_offset="458" filename="DISK" physical_partition_number="0" size_in_bytes="4" start_sector="208816" value="NUM_DISK_SECTORS-1695744." what="Update final partition with actual size."/>
</patches>
Click to expand...
Click to collapse
please note that it's two lines of the same code except one is partition0.bin and the other is DISK,
Do we need both? i know if i dont add the partiton0 section used in raw_program.xml then the drive is blank in linux,
now it's my understanding that the ebr comes as the forth partiton and it point to the next one , above in patch0.xml it start at NUM_DISK_SECTORS-1695744
i am still trying to better understand these figures,
Well time to grab coffee, i guess it's a dev night in.
the file MPRG8660.HEX can be renamed EMMCBLD.HEX and it triggers QPST to always look for a QDLoad mode phone and not debug, you can place all the files you need in one folder, i advise you to keep the originals in one location and only extract what your need to your worrking folder, copy emmcswdowload.exe from the QPST folder there too, we might need to do command line work, ive read that you can pre-create images in emmcswdownload (the same way 8660_msimage.mbn was created ) that you could just drop onto a phone once it's in emmc sd-card mode, almost a one click.
More info, plus help offered
Your welcome tyllerdurdent,
I am going to be putting a few hours into the dev from now actually for if you want assistance then no problems,
I also advise the following, download ubuntu live cd, it has a lot of tools your going to need to extract data you require, if we go step by step we might be good, i did a lot of test writing before i got my first boot, and that again only happens one in 20, i dont know why.
the rawpartiton0.xml above is incorrect for our devices as it states the first partion is 32mb, (i think it's ment to be amss.mbn, or NON-HLOS.mbn , our pit file which i did extract from my emmc dump says it's 105mb. i am confused and to why rawpartiton0.xml says the first bootloader is at start_sector="65537" but fdisk shows it as start 204801, i think someone needs to show me how to convert from blocks to sectors,
in patch0.xml it says
Code:
<patch byte_offset="506" filename="partition0.bin" physical_partition_number="0" size_in_bytes="4" start_sector="0" value="NUM_DISK_SECTORS-208801." what="Update MBR with the length of the EXT Partition."/>
Click to expand...
Click to collapse
208801 is where we have our ebr start,
i also think the IROM based pbl, sbl etc use the partition types in some way, why else have so many types? can any one explain that
this is a fdisk view of what i think our partition table looks like
Code:
Device Boot Start End Blocks Id System
/dev/sdb1 1 204800 102400 c W95 FAT32 (LBA)
/dev/sdb2 * 204801 205800 500 4d QNX4.x
/dev/sdb3 205801 208800 1500 51 OnTrack DM6 Aux1
/dev/sdb4 208801 208801 0 5 Extended
/dev/sdb5 212992 213991 500 47 Unknown
/dev/sdb6 221184 225279 2048 45 Unknown
/dev/sdb7 229376 234375 2500 4c Unknown
/dev/sdb8 237568 258047 10240 48 Unknown
/dev/sdb9 262144 263143 500 46 Unknown
/dev/sdb10 270336 271335 500 5d Unknown
/dev/sdb11 278528 279527 500 91 Unknown
/dev/sdb12 286720 307199 10240 93 Amoeba
/dev/sdb13 311296 511999 100352 c W95 FAT32 (LBA)
/dev/sdb14 516096 522239 3072 4a Unknown
/dev/sdb15 524288 530431 3072 4b Unknown
/dev/sdb16 532480 538623 3072 58 Unknown
/dev/sdb17 540672 741375 100352 8f Unknown
/dev/sdb18 745472 751615 3072 59 Unknown
/dev/sdb19 753664 759807 3072 5a Unknown
/dev/sdb20 761856 29843455 14540800 5b Unknown
/dev/sdb21 770048 790527 10240 ab Darwin boot
/dev/sdb22 794624 815103 10240 60 Unknown
/dev/sdb23 819200 839679 10240 94 Amoeba BBT
/dev/sdb24 843776 3911679 1533952 a5 FreeBSD
/dev/sdb25 3915776 8114175 2099200 a6 OpenBSD
/dev/sdb26 8118272 8736767 309248 a8 Darwin UFS
/dev/sdb27 8740864 9005055 132096 a9 NetBSD
/dev/sdb28 9011200 10035199 512000 95 Unknown
/dev/sdb29 10035200 30777343 10371072 90 Unknown
Oh, download wxdhex or wimlar program, you going to need a hex editor that can load BIG files , 16gb worth
i717-GB-Modem.zip IS THE SAME AS TAR?
i717-GB-Modem.zip 21.35 MB 7 0 2012-06-30 08:45:11
I could not find the i717-gb as tar file but I find it as a zip file. but I'm not sure about thif the contents are correct. Could you check
http://d-h.st/1aP
i717-GB-Modem.zip contents
META-INF
COM
GOOGLE
ANDROID
update-binary
updater-script
TMP
amss.bin
mdm.bin
Blocks and sectors
This may explain it , the different figure in the xml files
Because sectors are logical on the drive (Logical Block Addressing = LBA) you need to convert between LBA and physical (file system) sectors. This is pretty easy to do:
First - get a table of the start and end sectors of the partition table:
Code:
[[email protected] ~]# fdisk -lu /dev/hda
Disk /dev/hda: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 63 208844 104391 83 Linux
/dev/hda2 208845 4401809 2096482+ 83 Linux
/dev/hda3 4401810 8482319 2040255 82 Linux swap
/dev/hda4 8482320 234436544 112977112+ 5 Extended
/dev/hda5 8482383 29447144 10482381 83 Linux
/dev/hda6 29447208 50411969 10482381 83 Linux
/dev/hda7 50412033 52516484 1052226 83 Linux
/dev/hda8 52516548 234436544 90959998+ 83 Linux
Use this to determine what partition the bad sector is in. In this case 232962120 is inside the start and end values for /dev/hda5
NOTE: This is in partition 5 - ignore partition 4 as it is the extended partition. Any block from partitions 5 through 8 will also be in partition 4, but you want the real partition, not the extended partition.
Next, calculate the file system block using the formula:
b = (int)((L-S)*512/B)
where:
b = File System block number B = File system block size in bytes (almost always is 4096) L = LBA of bad sector S = Starting sector of partition as shown by fdisk -lu and (int) denotes the integer part.
For example:
The reported sector from the smart log above is 232962120, thus:
((14858312 - 8482383) * 512) / 4096 = 796991.125
^Bad Sec. ^Start Sec. ^Cha Ching! This is the sector!
(Use the block number from the smart test section, not from the smart error log section. They are using different methods of reporting file system vs. physical blocks.)
((BadBLock - StartPartition) * 512) / 4096
You can just paste this into Google as a template
Any fraction left indicates the problem sector is in the mid or latter part of the block (which contains a number of sectors). Ignore the fraction and just use the integer.
Next, use debugfs to locate the inode and then file associated with that sector:
Click to expand...
Click to collapse
[[email protected]]# debugfs
debugfs 1.35 (28-Feb-2004)
debugfs: open /dev/hda5
debugfs: icheck 796991
Block Inode number
796991 <block not found>
debugfs: quit
Ah! It didn't give the inode! It if did, you could have found the file with:
[[email protected]]# debugfs
debugfs 1.35 (28-Feb-2004)
debugfs: open /dev/hda5
debugfs: icheck 796991
Block Inode number
796991 41032
debugfs: ncheck 41032
Inode Pathname
41032 /S1/R/H/714197568-714203359/H-R-714202192-16.gwf
So what the heck? Why no inode? Well, remember how it said the sector might be bad?
Click to expand...
Click to collapse
the above copied from
http://timelordz.com/wiki/SMART_Rewriting_Bad_Sectors
i have a feeling we may need to shift our files (the basic files need to start odin are listed in rawpatch0 above, i dont know if that 100% true but it was the only files i wrote on by first sucess)
also
http://forum.xda-developers.com/showthread.php?p=31843525&postcount=13
in the above link they talk about the header of the qualcomm file
+------------+
|Dbl-preamble|
+------------+
|Dbl-header |
+------------+
|Dbl.bin |
+------------+
Click to expand...
Click to collapse
and
data_ptr = autodetectpage;
*data_ptr = sbl_header.codeword;
data_ptr++;
*data_ptr = sbl_header.magic;
data_ptr++;
*data_ptr = AUTODETECT_PAGE_SIZE_MAGIC_NUM;
Click to expand...
Click to collapse
now i used this in a way to find my bootloaders (i717 by this time, not shve-160l )
and to find the partitons
you will see in a hex editor at the start of each boot loader
something else to think about, my lack of success that last two days to produce a boot could be because my partitons are not clean , thats is to say if i write my sbl1 to 1000, and the trailing 0000 of the partition definition of my 99 block ebr/mbr ends at 999 , if i have dirt data between 999 and 1000 the cpu/pbl my interpret that as code(some of my boots is brick, some are into QDLoad, i have no pattern yet) , something i must test or confirm, or just worry about.
tyllerdurdent said:
i717-GB-Modem.zip 21.35 MB 7 0 2012-06-30 08:45:11
I could not find the i717-gb as tar file but I find it as a zip file. but I'm not sure about thif the contents are correct. Could you check
http://d-h.st/1aP
i717-GB-Modem.zip contents
META-INF
COM
GOOGLE
ANDROID
update-binary
updater-script
TMP
amss.bin
mdm.bin
Click to expand...
Click to collapse
Yes thats correct
updater script btw contains text, binary is the flashing exe i think,
Code:
run_program("/sbin/dd", "if=/tmp/mdm.bin", "of=/dev/block/mmcblk0p17");
run_program("/sbin/dd", "if=/tmp/amss.bin", "of=/dev/block/mmcblk0p13");
Click to expand...
Click to collapse
and a google of a simlar sansung product the skyrocket gives me a simlar pit layout
Device Name Size Part Name ODIN tar file Mount Point
mmcblk0boot0 512KB (empty) n/a (empty partition)
mmcblk0boot1 512KB (empty) n/a (empty partition)
mmcblk0p1 100MB SMD_HDR (partition info)
mmcblk0p2 500KB SBL1 sbl1.mbn
mmcblk0p3 1500KB SBL2 sbl2.mbn
mmcblk0p4 1KB (unnamed partition with '55 AA' MBR signature)
mmcblk0p5 500KB RPM rpm.mbn
mmcblk0p6 2MB SBL3 sbl3.mbn
mmcblk0p7 2500KB ABOOT aboot.mbn
mmcblk0p8 10MB BOOT boot.img
mmcblk0p9 500KB TZ tz.mbn
mmcblk0p10 500KB SSD n/a (empty partition)
mmcblk0p11 500KB PIT celox.pit
mmcblk0p12 10MB PARAM param.lfs
mmcblk0p13 98MB MODEM amss.bin /system/etc/firmware/misc
mmcblk0p14 3MB MSM_ST1 efs.img
mmcblk0p15 3MB MSM_ST2 n/a
mmcblk0p16 3MB MSM_FSG n/a
mmcblk0p17 98MB MDM mdm.bin /system/etc/firmware/misc_mdm
mmcblk0p18 3MB M9K_EFS1 efsclear1.bin
mmcblk0p19 3MB M9K_EFS2 efsclear2.bin
mmcblk0p20 3MB M9K_FSG n/a
mmcblk0p21 10MB DEVENC enc.img.ext4 /efs
mmcblk0p22 10MB RECOVERY recovery.img
mmcblk0p23 3MB FOTA n/a
mmcblk0p24 598MB SYSTEM system.img.ext4 /system
mmcblk0p25 2GB USERDATA userdata.img.ext4 /data
mmcblk0p26 302MB CACHE cache.img.ext4 /cache
mmcblk0p27 129MB TOMBSTONES tomb.img.ext4 /tombstones
mmcblk0p28 11.2GB UMS ums.rfs /mnt/sdcard
Click to expand...
Click to collapse
Other files
contents of the i717 boot loaders i used
ABOOT_SGH-I717M_I717MUGLA2_user_CL875155_REV00
Code:
527K Jan 6 2012 aboot.mbn
115K Jan 6 2012 rpm.mbn
72K Jan 6 2012 sbl1.mbn
111K Jan 6 2012 sbl2.mbn
601K Jan 6 2012 sbl3.mbn
117K Jan 6 2012 tz.mbn
other files pulled from
ABOOT_SGH-I717M_I717MUGLA2_user_CL875155_REV00 (no bootloader but all the other system files )
Hi.
Similar problem like here: http://forum.xda-developers.com/showthread.php?t=2334337
I am fighting with this phone two days.
In the first phase ( 18h ago) i connected by omap4boot and tried this - http://forum.xda-developers.com/showpost.php?p=39732470&postcount=20
next i did all wipes, i tried by cwm install this rom - u2_v20o_signed_022314_123556.zip
I thought all is good, but ofc still was logo LG.
Anyone LG FLash tool didnt work (i will explain it with screens after, when will can run into S/W mode)
I tried this http://forum.xda-developers.com/showthread.php?t=2292828
and i had very weird error:
Device descriptor:
bLength = 18
bDescriptorType = 1
bcdUSB = 528
bDeviceClass = 255
bDeviceSubClass = 255
bDeviceProtocol = 255
bMaxPacketSize0 = 64
idVendor = 451
idProduct = D00F
bcdDevice = 0
iManufacturer = 33
iProduct = 37
iSerialNumber = 0
bNumConfigurations = 1
reading ASIC ID
usb_write 4
usb_read 81
[*] read 0 bytes
NumOfSubblocks: 0x5
Subblock ID: 0x1
Subblock Size: 0x5
CH enabled: 0x7
ROM revision: 0x4
Checksum Subblock: 0x15
CHIP: 4430
IDEN: b1a3cecb3e5a097ee4d9313e2070f8863ca117f3
MPKH: 5f4092eccddf90fa43f546adf89508b31b9c74795e9516194c0ea6412fdcb7f6
CRC0: 9c669ad9
CRC1: 682adccf
sending 2ndstage to target... f0030002
usb_write 4
usb_write 4
wait 5-lelelel...
[*] msg size = 4
usb_write 21552
[*] data size = 21552
usb_close
Reopen usb...
Device descriptor:
bLength = 18
bDescriptorType = 1
bcdUSB = 528
bDeviceClass = 255
bDeviceSubClass = 255
bDeviceProtocol = 255
bMaxPacketSize0 = 64
idVendor = 451
idProduct = D00F
bcdDevice = 0
iManufacturer = 33
iProduct = 37
iSerialNumber = 0
bNumConfigurations = 1
waiting for 2ndstage response...
usb_read 4
usb read = aabbccdd
accepted 2ndstage response
sending image to target...
size = 246272
usb_write 4
usb_write 246272
** Done **
< waiting for device >
sending 'x-loader' (384 KB)...
OKAY [ 0.204s]
writing 'x-loader'...
OKAY [ 2.845s]
finished. total time: 3.050s
sending 'u-boot' (1024 KB)...
FAILED (status read failed (Too many links))
finished. total time: 107.422s
Done
Click to expand...
Click to collapse
Then i tried all ideas, which came to my head.
(Relock bootloader http://forum.xda-developers.com/showthread.php?p=44580559
p760-twrp-2.6.1-recovery.img
and much other, which i didnt remember...)
Finaly phone is bricking.
Any advices?
Edit:
Yesterday battery had 4.01 V, today has 3.7. I will try charge tomorrow.
Guys, what when i-loaded u-boot, x-loader after like i flashed JB rom by CWM ?
It can explain my current situation?
Look:
It are partiton for JB
View attachment 3762143
It are partition for ICS
View attachment 3762144
So i should now load some loader and boot file from JB?
Can U help me, pls?
I downloaded ICS stock rom. Exctracted it.
I made x-loader from file 0-gpt1.img. (256LBA-1023LBA). It is exactly same what file p1ics760.bin from fastboot by Lelus http://forum.xda-developers.com/showthread.php?t=2292828 )
once again i tried:
fastboot flash x-loader
fastboot flash u-boot
fastboot flash boot
fastboot flash recovery
All files are original from ICS stock rom.
No result.....
works only fastboot mode by software fastboot by Lelus.
Srsly this topic is so boring?
Edit:
Hm... u-boot file from here http://forum.xda-developers.com/showpost.php?p=39732470&postcount=20
is different from mine... x-loader is same like i wrote early...
It weird:
In Fastboot by Lelus - if i use any option between 2 and 7 - i get:
sending 'u-boot' (1024 KB)...
FAILED (status read failed (Too many links))
finished. total time: 107.422s
So i replaced file:
\fastboot\xu\p2ics760.bin
for original stock u-boot (in second try i replaced u-boot from this link http://forum.xda-developers.com/showpost.php?p=39732470&postcount=20)
(original p2ics760.bin i renamed to p2ics760.bin.old and u-boot.img i renamed to p2ics760.bin
and still is error - Too many links
But when i use:
fastboot flash u-boot u-boot.img - it hasn't error. It is same file!
Maybe the operation is successful, but in real it doesen't change anything? Is it possible?
Groszexxx said:
It weird:
In Fastboot by Lelus - if i use any option between 2 and 7 - i get:
sending 'u-boot' (1024 KB)...
FAILED (status read failed (Too many links))
finished. total time: 107.422s
So i replaced file:
\fastboot\xu\p2ics760.bin
for original stock u-boot (in second try i replaced u-boot from this link http://forum.xda-developers.com/showpost.php?p=39732470&postcount=20)
(original p2ics760.bin i renamed to p2ics760.bin.old and u-boot.img i renamed to p2ics760.bin
and still is error - Too many links
But when i use:
fastboot flash u-boot u-boot.img - it hasn't error. It is same file!
Maybe the operation is successful, but in real it doesen't change anything? Is it possible?
Click to expand...
Click to collapse
If you can enter in lelus fastboot, then flash a recovery wipe partitions and then with the recovery flash a rom....
My english is such bad or u didnt read the all posts? .
I flashed recovery partition much time. Telefon still is dead. Stock recovery, CWM, TWRP.
If I could flash recovery and after could "instal" rom - then it would not be problem .
Groszexxx said:
My english is such bad or u didnt read the all posts? .
I flashed recovery partition much time. Telefon still is dead. Stock recovery, CWM, TWRP.
If I could flash recovery and after could "instal" rom - then it would not be problem .
Click to expand...
Click to collapse
Then, If your L9 doesn't boot, it could be beacause a "IC power Cristal" or other hardware issue like EMM break (Eprom). In some case a box like http://octopusbox.com can solve the problem or in other case extract a log file with the exact issue details
A dead block of flash will produce CRC errors after or during the flash process and random lockups or reboots during operation. And if the fastboot problem strikes, you can issue commands via ADB, but after the necessary reboot there will be the PnP sound loop. If the phone is in Charge-only mode, ADB commands will be ignored, you can issue them, but **** happens.
Was there any positive feedback for the flash commands?
puntoazul said:
Then, If your L9 doesn't boot, it could be beacause a "IC power Cristal" or other hardware issue like EMM break (Eprom). In some case a box like http://octopusbox.com can solve the problem or in other case extract a log file with the exact issue details
Click to expand...
Click to collapse
It can be true. I received similar diagnosis about corrupt emmc. Anyway - for me it is possible but very unlikely (Ofc i havent experience).
lecorbusier said:
A dead block of flash will produce CRC errors after or during the flash process and random lockups or reboots during operation. And if the fastboot problem strikes, you can issue commands via ADB, but after the necessary reboot there will be the PnP sound loop. If the phone is in Charge-only mode, ADB commands will be ignored, you can issue them, but **** happens.
Was there any positive feedback for the flash commands?
Click to expand...
Click to collapse
Maybe i will show it on screens:
I run Fastboot by Lelus and set 2 option.
View attachment 3765116
And i get error:
View attachment 3765119
When i run fastboot by Lelus and set option 1 and type:
fastboot flash recovery 'filename'
View attachment 3765117
EHh, Finaly i think theory with emmc corrupt is are confirming.... after 30-40x flashed now i get one new and one very common error:
View attachment 3765322
View attachment 3765324
I am so sad! . But anyway, i am feeling much better when i know what is wrong with phone.
U-boot gets sent to the phone's RAM, but writing to its appropiate partition fails utterly. That is not necessarily hardware related. And nothing I've seen before. Either the partition got damaged or deleted, or it's in F2FS format. Artas' CM11 uses F2FS, EdwinMoqs CM13 as an option, and TWRP from 2.8.x can format partitions with F2FS.
But D/L mode is almost indestructible, only a bit tricky to invoke. And requires LG drivers. Even if the phone is no longer getting recognized by LG drivers and LG software because of a custom rom, when in D/L mode the LG driver should install a virtual COM port and the LG flash tool should now recognize the phone. Ihad difficulties flashing a KDZ file with LG Fladh Tool 2014,but the tool from the LG site, getting the stock rom directly from the server, works reliably, but it's best to flash twice in a row. If the phone auto-reboots into launcher, it's a success. If you see LG's stock recovery after the flash, flash another time.
Ok. if you run this command: "fastboot flash u-boot u-boot.img" (assuming that the u-boot.img file is for your l9 model), and result is cannot write in partition then EMMC is break (95% probability)
---------- Post added at 09:16 AM ---------- Previous post was at 09:13 AM ----------
lecorbusier said:
U-boot gets sent to the phone's RAM, but writing to its appropiate partition fails utterly. That is not necessarily hardware related. And nothing I've seen before. Either the partition got damaged or deleted, or it's in F2FS format. Artas' CM11 uses F2FS, EdwinMoqs CM13 as an option, and TWRP from 2.8.x can format partitions with F2FS.
But D/L mode is almost indestructible, only a bit tricky to invoke. And requires LG drivers. Even if the phone is no longer getting recognized by LG drivers and LG software because of a custom rom, when in D/L mode the LG driver should install a virtual COM port and the LG flash tool should now recognize the phone. Ihad difficulties flashing a KDZ file with LG Fladh Tool 2014,but the tool from the LG site, getting the stock rom directly from the server, works reliably, but it's best to flash twice in a row. If the phone auto-reboots into launcher, it's a success. If you see LG's stock recovery after the flash, flash another time.
Click to expand...
Click to collapse
Could be... perhaps if use Lg flash tool 2014 in emergency mode... (5% probability but is more than nothing) i hope @Groszexxx can revive his device
and if i was you... i try this... (see attach)
Yes, i talked about octoplus with someone, who has it. I never had anyone box . It is not my job . I was only curious what is it with phone my friend. I spend much hours on this issue. Anyway, i dont regret.
I will send phone to someone, who can flash it by some box like octoplus or jtag.
Thanks for lecorbusier post. I read much post, but this one is new for me.
So - time saying goodbye .
Maybe i will inform what will be next, maybe not ;p. We will see .
Thanks for all!
I bricked my phone (XT2041-1 "sofiar") by flashing an unnoficial build of TWRP 3.5.0 downloaded from a Telegram channel by doing:
$ fastboot flash recovery_a twrp-3.5.0-0-rav-sofia.img
$ fastboot flash recovery_b twrp-3.5.0-0-rav-sofia.img
$ fastboot reboot recovery
Since then, my phone is hard bricked - won't boot, recognized on Linux in EDL Mode only (i.e. ID 05c6:9008).
I got the latest official stock firmware, named SOFIAR_RETAIL_11_RPES31.Q4U-47-35-12_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip, from lolinet, and in its contents there's boot.img and recovery.img (among others).
I have qdl on my Arch Linux, and am wondering whether I can use it to flash the stock recovery image back to both slots and get my phone booting again.
How should I approach it?
P.s. I also got a blankflash from https://forum.xda-developers.com/t/...equest-solicitud-blankflash-g8-power.4431193/ that is supposed to get the phone working again, but am unsure whether using it will cause loss of data.
I absolutely cannot lose any data from internal storage.
Any help appreciated. Thanks in advance.
Ok, now we're rolling...
First things first. Motorola sucks because they only give you restricted Firehose loaders.
That means of the 70-odd partitions that you have you can only read/write about 1/3 of them using EDL.
If you post your Firehose loader I can tell you which ones you can read/write.
Second, are you sure that the only damage you did was by writing recovery_a and recovery_b?
And you're on Linux, *sad face*.
I was disassembling the Motorola Firehose for my Moto G (2021) and I discovered that they have more reboot options than stock.
There's reset-to-edl and reset-to-fastboot.
I've added those options to my edl.exe (in the sig) this morning. You need to download the very latest.
What may have happened is that you wrote a bad recovery which may have set the boot option in the BCB or misc.
Since the recovery is good enough to be recognized as an image but not good enough to reset this boot option you're stuck.
Your first recourse is flashing a proper recovery.
I'm not sure whether "blank flash" tries to wipe everything. In any case I wouldn't risk it.
Your first try should be to fix the broken things, not everything.
Yes, any edl client that supports ad-hoc xml should be able to get you to fastboot but I'll only answer for my code.
I've tested it.
Code:
C:\>edl /lwhatever.bin
C:\>edl /zf
C:\>fastboot flash recovery_a good_recovery.img
C:\>fastboot flash recovery_b good_recovery.img
C:\>fastboot reboot
I admit to not properly understand what a firehose loader is. :x
Second, are you sure that the only damage you did was by writing recovery_a and recovery_b?
Click to expand...
Click to collapse
Yes, 100%.
So, for now, I should try booting Windows, installing the 9008 driver and following your instructions... Will let you know how it goes.
Thanks a lot.
marc.2377 said:
I admit to not properly understand what a firehose loader is. :x
Click to expand...
Click to collapse
A Firehose loader is a replacement xbl/sbl secondary loader that has special sauce added to it to make it interactive.
It is not to be confused with a Windows driver (which, in this case is Zadig, as per the instructions on my web page).
In this case, your Firehose loader is packed in singleimage.bin in the RPE here: https://mirrors.lolinet.com/firmware/motorola/sofiar/blankflash/
I extracted it for you. I renamed it sofiar.bin
The extension name does not matter.
Code:
C:\>edl /lsofiar.bin
That's slash-ell-sofiar.bin
Edit: And yes, your Firehose loader has the reset-to-fastboot.
Right, thanks for the explanation. I figured that was programmer.elf from my files.
Ok, I got as far as:
> edl /l
Found EDL 9008
Serial: 69cccc95
HWID: 0010a0e102e80000, QC: 0010a0e1, OEM: 02e8, Model: 0000
Hash: 974359c4290cac7f-9f0dc9a802815b5e-2b376b7a7c1be92c-1e816b5287f18610
> edl /lsofiar.bin
Found EDL 9008
Resetting Sahara
Serial: 69cccc95
HWID: 0010a0e102e80000, QC: 0010a0e1, OEM: 02e8, Model: 0000
Hash: 974359c4290cac7f-9f0dc9a802815b5e-2b376b7a7c1be92c-1e816b5287f18610
Sending sofiar.bin 100% Ok
Waiting for Firehose... Ok
> edl.exe /zf
Found EDL 9008
Requesting reset to fastboot... Ok
But it doesn't boot to fastboot.
It seems to me that your tool, edl could be used to write the recovery partition directly, no?
I tried this:
> edl /w /precovery_a recovery.img
Found EDL 9008
Configuring... Ok
Requesting GPT 0 header... Ok, receiving... Ok, requesting entries... Ok, receiving... Ok
Requesting write recovery.img...
<log value="ERROR: range restricted: lun=0, start_sector=1591552, num_sectors=131072" />
Nope
P.s. curiously, the file I downloaded from https://raw.githubusercontent.com/b...a/0010a0e102e80000_974359c4290cac7f_fhprg.bin wasn't accepted as a valid firehose loader file.
Edit: nevermind. Had to restart the phone.
I believe that's an older loader, anyway.
How shall I proceed?
marc.2377 said:
But it doesn't boot to fastboot.
Click to expand...
Click to collapse
Hmm, the screen stays black?
Is it still in EDL mode or some other mode?
Does Windows "bong" when you pull the USB cable?
It's possible that this goes to a fastboot without a screen?
Try holding various buttons, both by long power button reset and /zf
marc.2377 said:
It seems to me that your tool, edl could be used to write the recovery partition directly, no?
Click to expand...
Click to collapse
Yes, it could if Motorola wasn't such a pain with the "range restricted".
They've really clamped down (that other file you mentioned is the same):
Code:
qcomview /r sofiar.bin
Addr LUN Start Count
------ --- -------- --------
007f10 0 0 256
007f28 0 256 78336
007f40 0 1609948 512
007f58 0 1610496 512
007f70 1 1 1
You can do this to see which partitions this means:
Code:
C:\>edl /lsofiar.bin
C:\>edl /g
I have a feeling that the Motorola "Blankflash" stuff writes something to those 3 areas that allow it to write everything.
But it probably wipes the userdata.
I'm not an expert on their tools.
Tell me what the GPT says (you only need to quote stuff in the area of that table).
Edit: It looks like in the multi GB zip there are two "instruction" files, flashfile.xml and servicefile.xml
They are mostly the same except that flashfile will wipe userdata!
Curious. The partition table is as follows:
Code:
Found EDL 9008
Configuring... Ok
Requesting GPT 0 header... Ok, receiving... Ok, requesting entries... Ok, receiving... Ok
# Name Start Count Type
-- ---------------- ---------- ---------- --------------------
1 xbl_a 256 9216 Inactive
2 xbl_b 9472 9216 Bootloader
3 tz_a 18688 8192 Inactive
4 tz_b 26880 8192 TrustZone
5 rpm_a 35072 1024 Inactive
6 rpm_b 36096 1024 Resource/power mgmt
7 hyp_a 37120 1024 Inactive
8 hyp_b 38144 1024 Hypervisor
9 devcfg_a 39168 256 Inactive
10 devcfg_b 39424 256 Device config
11 xbl_config_a 39680 256 Inactive
12 xbl_config_b 39936 256 Boot config
13 abl_a 40192 2048 Inactive
14 abl_b 42240 2048 Android bootloader
15 uefisecapp_a 44288 4096 Inactive
16 uefisecapp_b 48384 4096 be8a7e08
17 qupfw_a 52480 160 Inactive
18 qupfw_b 52736 160 QUP firmware
19 cmnlib_a 52992 1024 Inactive
20 cmnlib64_a 54016 1024 Inactive
21 cmnlib_b 55040 1024 Common lib
22 cmnlib64_b 56064 1024 Common lib64
23 keymaster_a 57088 1024 Inactive
24 keymaster_b 58112 1024 Key master
25 storsec_a 59136 256 Inactive
26 storsec_b 59392 256 Store secure
27 spunvm 59648 16384 Spun VM
28 uefivarstore 76032 1024 165bd6bc
29 multiimgoem_a 77056 64 Inactive
30 multiimgoem_b 77120 64 e126a436
31 multiimgqti_a 77184 64 Inactive
32 multiimgqti_b 77248 64 846c6f05
33 prov_a 77312 512 Inactive
34 prov_b 77824 512 d05e0fc0
35 modem_a 78336 368640 Inactive
36 modem_b 446976 368640 FAT32
37 fsc 815616 256 FSC
38 ssd 815872 16 Secure SW download
39 dsp_a 816128 65536 Inactive
40 dsp_b 881664 65536 DSP
41 ddr 947200 2048 DDR
42 utags 949248 1024 1dd40d18
43 utagsBackup 950272 1024 c490f39c
44 modemst1 951296 8192 Modem ST1
45 modemst2 959488 8192 Modem ST2
46 fsg_a 967680 49152 Inactive
47 fsg_b 1016832 49152 Modem storage
48 persist 1065984 65536 Persist
49 prodpersist 1131520 16384 Persist
50 frp 1147904 1024 FRP
51 cid 1148928 256 459abd04
52 carrier 1149184 32768 c63d32d8
53 metadata 1181952 32768 988a98c9
54 kpan 1214720 16384 56465e10
55 boot_a 1231104 131072 Inactive
56 boot_b 1362176 131072 Boot
57 dtbo_a 1493248 49152 Inactive
58 dtbo_b 1542400 49152 DTBO
59 recovery_a 1591552 131072 Inactive
60 recovery_b 1722624 131072 Recovery
61 misc 1853696 2048 Misc
62 logfs 1855744 16384 Log FS
63 apdp 1872128 512 APDP
64 msadp 1872640 512 MSADP
65 dpo 1873152 2 DPO
66 devinfo 1873160 8 Device info
67 bluetooth_a 1873168 9216 Inactive
68 bluetooth_b 1882384 9216 Bluetooth
69 logo_a 1891600 66848 Inactive
70 logo_b 1958448 66848 Splash
71 vbmeta_a 2025296 128 Inactive
72 vbmeta_b 2025424 128 Verified Boot meta
73 padA 2025552 6064 Empty
74 hw 2031616 16384 b2d77ec0
75 padB 2048000 16384 Empty
76 sp 2064384 16384 40aef62a
77 padC 2080768 16384 Empty
78 padD 2097152 32768 Empty
79 super 2129920 16973824 System
80 userdata 19103744 103038943 User data
Doesn't seem to match the output of qcomview.
Also, the file 0010a0e102e80000_974359c4290cac7f_fhprg.bin lists the following codenames:
Code:
QCA6390
QCS605
SA8150
SDA670
SDA845
SDA855
SDA855A
SDA865
SDC830
SDM450
SDM670
SDM830
SDM845
SDM855
SDM855A
SDM1000
SDX24
SDX24M
SDX55
SM6150
SM6150P
SM7150
SM7150P
SM_NICOBAR
While programmer.elf (same as sofiar.bin that you uploaded) lists, additionally, QCM_NICOBAR and QCS_NICOBAR.
I wonder whether this is actually the correct file for me...
Btw, before attempting any further writing strategies, I confess to being interested in pulling userdata. As I understand the real decryption key is stored in the TEE functionality of the chipset and such an image would be unreadable for me, except if I were to restore it later.
With your tool I got the "range restricted" for edl /r /puserdata parts\userdata.img /t too.
Code:
Addr LUN Start Count
------ --- -------- --------
007f10 0 0 256 - GPT
007f28 0 256 78336 - xbl_a to prov_b
007f40 0 1609948 512 - ??? random spot in recovery_a
007f58 0 1610496 512 - ??? random spot in recovery_a
007f70 1 1 1
So, basically, you have free read/write access to partions 1 to 34
Reading is always safe.
Also, you're on the B slot.
So why does reboot to fastboot fail?
It could be that it was never implemented correctly in this Firehose
It could be that this Firehose is not for your device
It could be that xbl and/or abl was damaged somehow
I'd do some checking, xbl_b and abl_b to start with.
Read 'em then compare them to the xbl and abl you have in your big packages.
Code:
C:\>edl /lsofiar.bin
C:\>edl /r /t /pxbl_b xblb.img
C:\>edl /r /t /pabl_b ablb.img
The /t will copy these ELF files only as big as they need to be (not all the blank space).
OTOH, they will enlarge to an exact number of 512 byte sector.
So they could be 511 bytes bigger than what comes out of that package.
If things are wacky, try without /t, but they'll be padded with all the zeroes in the partition.
If those files aren't in the big package, here's ones I extracted from the blankflash.
Check 'em all.
Also, it's possible that somehow the slots got switched.
While you're at it, look at xbl_a and abl_a also.
Hey, thanks for the continued efforts to help me. Sorry for absence for the past days, real life caugh in ^^
I'm glad to report that, amidst some binary checking and all that, I managed to resuscitate my phone using the blankflash strategy, after carefully revising it.
Strangely, it seems that TWRP got installed in the boot partition, such as that "normal boot" kept entering TWRP, despite I having flashed the stock recovery images to both recovery slots. I'll detail this all later.
At this point my phone is on and I backed up what I needed, and have been using it. A few strange glitches are present, i.e. battery charging is acting weird. I plan on doing a clean flashing of the stock ROM soon. Maybe I should take the opportunity to study how to make a fully working port of the latest LineageOS for this device, too.
Will get back within a few days with a detailed report of the endeavour
marc.2377 said:
Will get back within a few days with a detailed report of the endeavour
Click to expand...
Click to collapse
I'm looking forward to hearing how you got EDL mode working.
I bricked XT2041-3 Sofiar (downgrade to A10) and am stuck trying the phone to succeed at qboot blank-flash, but it hangs (on linux):
Code:
< waiting for device >
Motorola qboot utility version 3.86
[ 0.000] Opening device: /dev/ttyUSB0
[ 0.000] Detecting device
[ 0.002] ...cpu.id = 266 (0x10a)
[ 0.002] ...cpu.sn = 3773339940 (0xe0e89924)
[ 0.002] Opening singleimage
[ 0.002] Loading package
[ 0.004] ...filename = pkg.xml
[ 0.005] Loading programmer
[ 0.005] ...filename = programmer.elf
[ 0.005] Sending programmer
[ 0.178] Handling things over to programmer
[ 0.178] Identifying CPU version
[ 0.178] Waiting for firehose to get ready
With --debug=2 there can be seen some parsing errors in xmls being passed for about 13 more seconds. On Windows VM phone is recognized as a single QDLoader 9008 device, but qboot fails after half a minute with IO Errors. Is this even EDL mode?
A tried without luck Renate's edl tool. edl.exe /lsingleimage.bin:
Code:
Found EDL 9008
Could not open device
I was growing increasingly desperate, so I opened the phone and played with EDL points according to
MatiasLopezxD. No combination of vol-, power, shorting points, plugging usb seem to make a difference. I must be missing something simple.
Any help would be appreciated.
@ybea: Quick answer for now - I got into EDL mode by holding down VolDown+Power for about 8-10 seconds. Let me know if it works for you. What's your output for lsusb?
Same as yours - ID 05c6:9008 (Qualcomm, Inc. Gobi Wireless Modem (QDL mode)). It reconnects after pressing power for 9 seconds (with or without vol-), nothing new.
Try restarting it into EDL mode while it's plugged. I found that to be necessary sometimes.
Edit: Btw, I don't remember why exactly, but I only had success running the blankflash from Windows. Linux didn't do the magic, nor a Windows VM with USB redirection...
marc.2377 said:
Edit: Btw, I don't remember why exactly, but I only had success running the blankflash from Windows. Linux didn't do the magic, nor a Windows VM with USB redirection...
Click to expand...
Click to collapse
That was it! I didn't event try it on the metal, because Motorola driver installer and uninstaller crash for me for some reason. Should be straightforward from now.
Thank you so much. You saved the day.
ybea said:
A tried without luck Renate's edl tool. edl.exe /lsingleimage.bin
Click to expand...
Click to collapse
Sorry. edl.exe uses the generic Zadig (i.e. WinUsb) driver).
If you have the Qualcomm driver loaded it's stealing the poor WinUsb interface and forcing it into some bogus virtual com port.
Also, singleimage is Motorola's completely morally bankrupt idea of packing stuff in a file.
It is not a Firehose loader, although it contains one.
Add to all your miseries, Motorola is crap and releases only restricted Firehose loaders.
If you're still stuck, ship me the "single-and-totally-bogus.bin" and I'll extract the Firehose loader for you.
Better poke me or I won't see it.
No longer stuck. The problem for me was neither VM USB passthrough nor blankflash tools for linux did work, although both showed proper EDL mode. It seems it only works on native Windows. Thanks for your interest.