Got a free n200 through tmobile to use as a hotspot device for my pc. I was previously getting the job done by using a galaxy note 3 and setting my pc's ttl to 65 but apparently that doesn't work with the newer phones.
I did some searching online and haven't been able to get a definitive solution to bypassing the hotspot throttle, as people seem to have varying results.
Had a lot of issues with PDAnet+, so it's definitely not a long-term solution for me.
Just sent an unlock request to OnePlus, hopefully by next week I'll get the unlock file and I'll root the phone. I'm assuming that rooting the phone will expand my options for what I want to do. Anyone have a solution that worked for them?
Yo, it's like dns hijacking, in fact, this is what you have to do to bypass this.
I'll paint a scenario, see what you make of it...
I plug my sim into a wifi router, in the control panel of this router, I set the wifi to use the 2nd ip, (yes, all isp's actually give you 2 ip's, one that is public, one the isp use's to spy on you, and the one you see in your ethernet card, usually 192.168.1.1.
Your wifi router runs adb, so it is on a different network, being 192.168.0.1, if you set your connecting device to your public ip shown by the router, and nxbogus domain your isp's private number seen in the router, (usually 100.whatever) and their dns, then set your prefered dns in the connecting device, you will bypass the throttling, but you will notice something else...
They throttle you by lowering your phones coverage lol...
Notice in your wifi setup pages your signal will drop from say 75% to 25%, and if you check the config logs, you'll see your limited 90% by the isp..
Yup, I'm isp level in this department..
didn't understand half of what you said. can you break it down a lil bit more?
l0csta said:
Got a free n200 through tmobile to use as a hotspot device for my pc. I was previously getting the job done by using a galaxy note 3 and setting my pc's ttl to 65 but apparently that doesn't work with the newer phones.
I did some searching online and haven't been able to get a definitive solution to bypassing the hotspot throttle, as people seem to have varying results.
Had a lot of issues with PDAnet+, so it's definitely not a long-term solution for me.
Just sent an unlock request to OnePlus, hopefully by next week I'll get the unlock file and I'll root the phone. I'm assuming that rooting the phone will expand my options for what I want to do. Anyone have a solution that worked for them?
Click to expand...
Click to collapse
you could always use this classic app been around for yrs its called pdanet/Foxfi........ http://foxfi.com/
PopCaps1996 said:
you could always use this classic app been around for yrs its called pdanet/Foxfi........ http://foxfi.com/
Click to expand...
Click to collapse
yea i'm using easytether rn, very similar to foxfi and pdanet+... not a permanent solution however, as it tends to randomly disconnect and i often get kicked out of games due to "network lag". Speeds are exponentially faster than the throttled hotspot, however, so i wont complain.
still, would be nice if there was a solution to this for the native hotspot/tether features... tried everything with apns and changing the ttl on the phone but it didn't work.
looks like someone found a solution for the moto g 5g here, maybe i'll try to implement this for the n200, could be a possible workaround.
l0csta said:
yea i'm using easytether rn, very similar to foxfi and pdanet+... not a permanent solution however, as it tends to randomly disconnect and i often get kicked out of games due to "network lag". Speeds are exponentially faster than the throttled hotspot, however, so i wont complain.
still, would be nice if there was a solution to this for the native hotspot/tether features... tried everything with apns and changing the ttl on the phone but it didn't work.
looks like someone found a solution for the moto g 5g here, maybe i'll try to implement this for the n200, could be a possible workaround.
Click to expand...
Click to collapse
moto g solution you posted requires a special kernel. usb tethering through PDAnet+ paid version works fine, the key is you dont enable it thru the native tethering, instead enable USB tethering through the PDAnet app and leave the phone on charging mode so it can make a ADB connection. Make sure ADB is working and you can establish a working adb connection from PC to phone first prior to attempting to tether since it will use ADB. i get full speeds tethering using the paid version.
AiM2LeaRn said:
moto g solution you posted requires a special kernel. usb tethering through PDAnet+ paid version works fine, the key is you dont enable it thru the native tethering, instead enable USB tethering through the PDAnet app and leave the phone on charging mode so it can make a ADB connection. Make sure ADB is working and you can establish a working adb connection from PC to phone first prior to attempting to tether since it will use ADB. i get full speeds tethering using the paid version.
Click to expand...
Click to collapse
yeah i've been doing this via easy tether, gets the job done for the most part
For me, PDAnet has low throughput while EasyTether runs full speed and can be used with OpenWRT. They both disconnect randomly though.
No reason to deal with that if you have root. AdGuard+VPNHotspot+noprovisioning is easy to setup and works fine for most networks.
l0csta said:
didn't understand half of what you said. can you break it down a lil bit more?
Click to expand...
Click to collapse
Only connection is WAN to WAN!
Ok, first, I use an lte wifi router, enter gui, goto lan, change router login ip to any ip not 192.168.1.1 or 192.168.0.1, the latter is hidden in router, but when trying to connect 2nd router, using this ip, problems appear, because the 1st router has adb enabled due to the lte section of 1st router being android 6, and uses's it.
So in effect, I set 1st routers address to 192.168.1.5, 255.255.254.0, 192.168.1.3 ie, this is 1st router login address. In the 2nd router I set mac address of 1st router to use 192.168.1.3, having been set in the 1st.
I do this because if I set 2nd router to match 1st routers address, the 2nd router auto changes address, when plugged in to first, and the 1st router changes too.
So now that you can goto 192.168.1.1 in 2nd router with 1st plugged in, try 192.168.1.3.
First part over, now the tricky part...
Disconnect 2nd router (this Will become your MAIN router)
Start 1st router with sim in, only to obtain public ip, because you need to set this ip in WAN of 2nd router. If your ip changes every reboot, you need to check public ip from first router match's what you set the wan ip to in 2nd router.
Now when you are in 1st router's network/lan settings, look for option to use 2nd ip. enable it, in the ip box put your public ip, ie your internet ip, and remove all access to anything else, including disabling wifi, both 2.5 and 5g.
So now plug in 2nd router WAN to first routers WAN.
Go into 2nd router, and block the PRIVATE ip seen in 1st router, the ip the isp shows you, and NX=bogusdomain your isp's private dns
In your WAN page of 2nd router, set preferred dns.
Voila.
70-80% increase in response.
The hardware method to block dns hijacking
Ps any reboot of the first router will change its ip due to being lte, so remember to check 2nd router match's after any power outage...
Related
I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (for the Hermes). It should currently be "BTPAN1".
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc")
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. I imagine this will drain your battery in a hot minute, so bring your charger.
UPDATE (28-Oct-2007): Attached are some more beta releases of patched intshare.dll. I've created versions for most of the adapter names people have requested. By renaming this dll to intshare.dll and copying it to \Windows, Internet Sharing will use TIACXWLN1 (or whichever dll you use) when Bluetooth PAN is selected. I.e., if you use this, you will not need to make the registry changes above.
This will handle the registry part, but of course you'll still need to set up the ad-hoc network on your own.
UPDATE (03-Nov-2007): I've attached a beta version of the patched Internet Sharing app. It's in its own cab so it won't overwrite your existing IS. This app replaces Bluetooth PAN with 802.11b/g Wireless Ethernet. No registry hacking required. This app is well suited to replace the MS version on cooked ROMs.
If you use an adapter other than TIACXWLN1 then replace intshare.dll just as before.
UPDATE (08-Nov-2007): Attached is v 0.9.1 of the Internet Sharing Mod. This update addresses the 10 minute disconnect bug most people have experienced.
best,
fluxist
This is the first thing I'll try when i'm at home again!
I can't believe this! Waiting for this since i got my Hermes. Thx for this development. This is the greatest effort since Hard-SPL and WM6 upgrade.
Now I can connect my XBOX360 to the Internet without starting my PC and sharing it over PC-LAN. USB-Charger is at the Front of the XBOX360.
I hope it will work.
You said the Max-Connections can be reworked. Does this mean it will support Ad-Hoc AND WLAN-Routing to many recepients too?
This worked for me too on a Kaiser/TYTN II
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
odessaranger said:
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
Click to expand...
Click to collapse
not sure what you mean by replacing the connection. With ICS, obviously you cant share your connection over BT while sharing it over WIFI. and you can normally use wifi to connect to another computer by using an ad-hoc connection and manually entering a private ip on the same subnet for each computer.
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
boniestlawyer said:
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
Click to expand...
Click to collapse
Were you able to use more than one client connected?
I'll admit..when I saw this my first thought was that this was another "How can I do internet sharing via wifi" and the title was just misleading..instead I find myself very impressed with your accomplishment. Very well done! As a "hack" untill you figure out how to mod the dll which I'm sure is only a matter of time now that you have pointed everyone in the right direction, you can export the registry key for both the Bluetooth adapter and the Wifi one and "import" whichever one you want to use at a given time...it's not pretty but it should work.
Some issues of concern would be that the AP is wide open and can be connected to by anyone with no password etc...the bluetooth pairing allowed some security but using the wifi doesn't have the same shared key protection...or am I missing something obvious?
fluxist said:
I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
When I used it I was only able to get one client to connect, however there is a reg value, HKLM\Comm\BTPAN1\Parms\MaxConnections that may help if it is changed from 1 to 2 (or whatever). But I haven't tried.
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. So that's a good thing, although I imagine this will drain your battery in a hot minute, so bring your charger.
I was going to release a patched intshare.dll so that the normal Internet Sharing utility can do this, but I'm having trouble changing the section addresses in the dll to the right values after I add data. If anyone knows how to do this PM me and I'll give you the details.
best,
fluxist
Click to expand...
Click to collapse
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
I ran into same issue with XP internet sharing. Another workaround is to have a linux machine do NAT( since you can specify the IP used there) to whatever other clients you want and have it connected via bluetooth dun or bluetooth PAND (which is the solution I use to give internet to my replaytv and a couple of laptops in the house)...my edge connection is my main internet feed..a cacheing proxy such as wwoffle, squid of my personal preference "polipo" helps alot to when using gprs/edge etc since it helps with the latency.
fluxist said:
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
Click to expand...
Click to collapse
Impact on BT?
What a brill find. Well done.
Does it break anything with bluetooth?
Tx
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
if someone manages to get this working with xbox 360 make a tutorial plx ;D
superflysocal said:
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
Click to expand...
Click to collapse
thats what i wanna know , could i use my hsdpa connection via wifi to my psp?
I'll do a tutorial when i'm at home again. Maybe somebody with know-how can make a cab-file v1.0 for this "WLAN-Modem hack".
This surely will be a great app.
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
when you say click "IEEE 802.11b/g Compatible Wi-Fi" do you mean the wifi network adapters in my case would be "tiacxwln compatible wireless ethernet"? im trying it on a 6700 WM5
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
Got it - except on my device it's Programs -> accessories -> IS
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
Check - but is the T1ACXWLN1 device specific? If so, how can I find the interface ID on my device?
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
For me it's settings -> connections -> network cards, but I don't have an IEEE 802.11 listed. I connected to an existing AP, and found that my 'SDIO WLAN Wireless Adapter' does receive a DHCP address, so I tried changing it to 192.168.1.1...
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
Found this and set up my WING-FI network.
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
The client PC connects to WING-FI, but never receives an IP address...
What could I be doing wrong? Is it the hardware ID in the registry? I've created the network with WPA, then after the connection problems, with no security - but still no change.
Thanks!!
Ryan
neonstorm said:
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues...
Click to expand...
Click to collapse
Very likely the string TIACXWLN1 needs to be something different. Check HKLM\Software\WZCSV\Parameters\Interfaces\
There should be a key there with the name of your wireless adapter. It should end in "1".
And if not there, it should also be visible under HKLM\Comm\
Let us know how it works out.
EDIT: I just noticed you typed T1ACXWLN1. The string must be TIACXWLN1. That's "i" not one.
fluxist
I own a PPC6700 as well and I was able to get it working no problem other than the fact that our wireless adapter is not the same as the one mentioned. The reg edit is the same it's just the first network adapter in the list when you create the network settings.
fluxist said:
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
Click to expand...
Click to collapse
If you send me the dll I could look into it.
i have some experience with editing dlls.
good work man
A couple of days ago my wireless connection quit working at home. The wireless network icon turned white all the time, and never switched to green. I hard wire the modem/router (ATT Uversre 2Wire 3800HGV-B) into a 5 port switch and plug my computer, network storage drive, and media streaming box into the switch. I've had all of this set up for a few months in it's current configuration and there was never an issue before. This just seemingly happened out of the blue...funny how computers do that sometimes, right? I have an HTC Aria, I was running CM7 RC1 when the problem happened, I just updated to RC2 hoping maybe it would change and it didn't.
After reading posts and checking settings here's what I've found:
My wireless router is set to act as the DHCP server. I set all of the IP addresses manually. I've had it set this way for some time, haven't made any changes recently. The attached network storage (D-Link DNS 323 also has DHCP server capability, but that is disabled)
I found that while my phone was set in the router's setting to connect to 192.168.1.67 for whatever reason it was connecting to 192.168.0.200 (which is out of range, my DHCP is set to address to 192.168.1.64 - 192.168.1.253)
Any idea what would cause this?
I have a temporary fix right now, I've set the phone for static IP and entered all the values. It now connects to my home network on the correct IP and appears to work. This will be a hassle though because there will likely be conflicts when I try to connect to public wifi or at my office. I could just go in and set it back to automatic IP when I leave home....but that is a hassle, and obviously, something isn't working quite right.
Anybody have a clue what would be making this happen?
thanks!
theWilly said:
A couple of days ago my wireless connection quit working at home. The wireless network icon turned white all the time, and never switched to green. I hard wire the modem/router (ATT Uversre 2Wire 3800HGV-B) into a 5 port switch and plug my computer, network storage drive, and media streaming box into the switch. I've had all of this set up for a few months in it's current configuration and there was never an issue before. This just seemingly happened out of the blue...funny how computers do that sometimes, right? I have an HTC Aria, I was running CM7 RC1 when the problem happened, I just updated to RC2 hoping maybe it would change and it didn't.
After reading posts and checking settings here's what I've found:
My wireless router is set to act as the DHCP server. I set all of the IP addresses manually. I've had it set this way for some time, haven't made any changes recently. The attached network storage (D-Link DNS 323 also has DHCP server capability, but that is disabled)
I found that while my phone was set in the router's setting to connect to 192.168.1.67 for whatever reason it was connecting to 192.168.0.200 (which is out of range, my DHCP is set to address to 192.168.1.64 - 192.168.1.253)
Any idea what would cause this?
I have a temporary fix right now, I've set the phone for static IP and entered all the values. It now connects to my home network on the correct IP and appears to work. This will be a hassle though because there will likely be conflicts when I try to connect to public wifi or at my office. I could just go in and set it back to automatic IP when I leave home....but that is a hassle, and obviously, something isn't working quite right.
Anybody have a clue what would be making this happen?
thanks!
Click to expand...
Click to collapse
I don't understand when you say your router is your DHCP server but you set all the addresses manually...I can understand setting your network storage and media streaming to static IP's but you may want to reconsider for everything else, if your router allows for that to happen.
Have you tried rebooting your router and switch? May be worth doing that. I would not recommend a RESET because you'll have to reconfigure everything and I know how much of a hassle that is.
So, when you say you set the phone for static IP, do you mean through the phone gui or through the router?
Another thing to check is the number of available IP addresses. You could be out. I doubt this is the case in a home network, but never hurts to check.
"Do you mind if I turn up the AC?"
I have somewhat of a similar situation... I just installed CM7 RC2 and I can connect to my home's wifi and browse the internet etc... but some apps like Facebook won't update. With Facebook, I can retrieve messages sent to me but the news feed never updates and I can't view profiles. And for some reason everything works when I use my university's wifi...
corber22 said:
I have somewhat of a similar situation... I just installed CM7 RC2 and I can connect to my home's wifi and browse the internet etc... but some apps like Facebook won't update. With Facebook, I can retrieve messages sent to me but the news feed never updates and I can't view profiles. And for some reason everything works when I use my university's wifi...
Click to expand...
Click to collapse
Have you checked (turned on) your Background Data and Auto-sync?
Menu > Settings > Accounts & Sync ......
Have you checked (turned on) your Background Data and Auto-sync?
Menu > Settings > Accounts & Sync ......
Click to expand...
Click to collapse
Yeah, it's on. Still doesn't work. One other thing I noticed is that even though I'm with At&t the Amazon App Store works when I'm using my university's WiFi but no where else...
corber22 said:
Yeah, it's on. Still doesn't work. One other thing I noticed is that even though I'm with At&t the Amazon App Store works when I'm using my university's WiFi but no where else...
Click to expand...
Click to collapse
Go here and download the latest Nightly cm_liberty_full-30.zip
WiFi performance has been dramatically improved since RC2, and if nothing else, it's a better place to continue trouble shooting from.
Go here and download the latest Nightly cm_liberty_full-30.zip
WiFi performance has been dramatically improved since RC2, and if nothing else, it's a better place to continue trouble shooting from.
Click to expand...
Click to collapse
Didn't help I don't get what's happening. I can use the browser fine but certain applications always time out and won't update.
I have the same problem. I've found the following apps to not work correctly when I connect my Sprint HTC Evo 4G (CM 7.0.3.1) to my home wireless network (Apple Airport Extreme Base Station):
Facebook (news feed won't update)
Amazon MP3 (Only the cloud player doesn't work)
Netflix (won't let me log in)
Speedtest (downloads fine but shows 0.00Mbps for uploads)
Again, all features works great on 3G or on the wifi at work (a university network running WPA2 Enterprise with LEAP authentication), which leads me to suspect there's something wrong with my home wifi setup. I have updated the Airport Extreme to the latest firmware and reset it several times yet the problem persists. Any ideas?
OK so work have blocked several of us from connecting our phones to wifi. Now we have a router her but can not access it so image they blocked at the main offices where they manage the network. Their are several houses that have their own routers etc but connected to the same network if that makes sense.
So my question is first how would they block us and second how can we bypass it?
Sent from my GT-I9100 using Tapatalk 2
Several ways to block access to a wifi routers.
Ways to access the network would be bring your own from home,and plug it in to the network.
To many ways to block you out to know what they have done.
Sent from my HTC Wildfire S A510e using XDA
Probably two reasons why they did this -
1) Prevent rogue devices connecting to their network, i.e. devices they cannot control what is on them and therefore could introduce viruses into the network or allows others to hack in and steal data etc.
2) Prevent people connecting personal devices for personal use, downloading files, facebook etc. Using company time and resources for unproductive personal tasks.
Probably easiest to ask them why and to ease the restrictions.
On the how:
You can control what connects to what on a very fine level - by device, by what it does and who it can talk to.
Ye I understand why. They blocked us as their network is really slow and rubbish but when we do nights and no one is using it its nice to be able to connect as no signal their. Just wondered if their was a way to get around it. They seem to have blocked all phones that were connected but one that was has been able to reconnect which is a blackberry.
Sent from my GT-I9100 using Tapatalk 2
How to by pass works blocking phone 2 options
By pass I've discovered! May not work for all
WARNING TRY AT YOUR OWN RISK!!
#1 way I've discovered (in my office)
(Other wise try bring your own wifi router and setting the ssid to company's name )
If you have a pc or Mac computer and plug Incoming Ethernet port into LAN port not WAN then from 1-4 LAN port into pc/Mac Ethernet )
Try hiding your wifi router either in tower box or in desk try to be not so obvious leaving cables everywhere , don't just leave out in the open for everyone to see..
What I did
(I've hide the router in the under my desk using 3M double sided tape and tucked the cables away so there not hanging down)
#2 way ( works anywhere you can get a wifi signal)
My. Discovered by pass :
I got a wifi repeater/ range extender
I've programmed it to my work network with their ssid and password
Then
On the repeater / extender
Your new Access Point
I used the same ssid but used a different password
(At this point you have created your own AP , which logins to your network wifi and then
Now
When I go home I just unplug my repeater and lock it up in my desk
Good luck Jason
Ps: option #1. if you need more help try YouTube if your confused what to do with wifi router
SEARCH "using old router as a wifi extender (or as second AP)
My boss already block ssid wifi for usage at handphone, only laptop can connect that wifi. How i can connect wifi via my handphone? Currently i use i phone 6s.
Any trip for unblock for connect to my phone?
What kills me about my situation is some dumb ass did streaming video one day and ran up like XXXX gb of data so naturally they started giving a damn about who was doing what... I got banned/blocked even though I've never streamed... I'm assuming I'm blocked... got the right password and my old phone said authentication failed. My new phone it doesn't say or haven't found where it says yet... I can't bring in my own connection as I don't have a office of my own and the building is too big and metal for the mobile signal to make it to my location...
edit: According to my idiot boss they're getting strict I guess and just blocking most stuff... ?
"How did you happen to do such thing - and on your last day at the job..."
Hope someone can help with this: rooted the other day using the htc unlocker method. so s-on with root and still stock rom..have not changed anything other than install busybox. no other changes. have not even gotten to flashing roms yet. So the phone will not recognize my home towifi. when it scans for networks, it sees everybody (neighbors) but mine as being in range (even tho i am sitting next to it). at one point i finally got it to connect yesterday, but then when i went to work it never disconnected and returned to 3g, so when i went to use my internet for something it said it was still connected, when in fact it wasn't. so no data and no 3g. I had to physically turn off wifi to get the phone to be able to connect to 3g. now i am back home, it will not connect again. the phone does not see my network as being "in range", therefore will not connect.
I have several other devices that connect to the network just fine (like my laptop I am typing on).
any ideas would be greatly appreciated.
There's an app called WiFi analyzer and WiFi manager available on the play store. Idk y it isn't connecting to your WiFi now when it did before, but maybe one of these 2 apps can help.
WiFi analyzer will tell u what channels thw other WiFi networks are on in your area. It could be an issue of interference. It will also tell u the best channel to put your WiFi on to avoid that interference.
Do u have best WiFi performance on in settings-WiFi? Turn it off/on see if it makes a difference. Off is optimal since it kills batteries.
WiFi manager helped my phone recognize and connect to open networks quicker than stock settings did. Maybe try that as well.
Is your connection password secured? WPA/WPA2, WPK? Is it a linksys router? Try making a static ip for your phone. My phone would never connect at work on an open network until I made it a static ip. Or it would connect and never send data.
Actually, try that first, I forgot about that. If its an older linksys router that's probably what it is.
Anthonicia said:
There's an app called WiFi analyzer and WiFi manager available on the play store. Idk y it isn't connecting to your WiFi now when it did before, but maybe one of these 2 apps can help.
WiFi analyzer will tell u what channels thw other WiFi networks are on in your area. It could be an issue of interference. It will also tell u the best channel to put your WiFi on to avoid that interference.
Do u have best WiFi performance on in settings-WiFi? Turn it off/on see if it makes a difference. Off is optimal since it kills batteries.
WiFi manager helped my phone recognize and connect to open networks quicker than stock settings did. Maybe try that as well.
Is your connection password secured? WPA/WPA2, WPK? Is it a linksys router? Try making a static ip for your phone. My phone would never connect at work on an open network until I made it a static ip. Or it would connect and never send data.
Actually, try that first, I forgot about that. If its an older linksys router that's probably what it is.
Click to expand...
Click to collapse
I will try some of those things, but I don't think that is it. whatever is wrong is coming from root. everything was fine before that. and i don't know anything about setting up a static ip. not a linksys, btw.
greek goddess said:
I will try some of those things, but I don't think that is it. whatever is wrong is coming from root. everything was fine before that. and i don't know anything about setting up a static ip. not a linksys, btw.
Click to expand...
Click to collapse
Root doesn't have anything to do with your WiFi. It is highly unlikely anyways. Google how to set up static ip. U can do it right from your phone.
Your router doesn't show up at all or does is try to connect and nothing? Mine tried to connect and nothing. To set up a static ip your phone needs to at least see the router.
If you're rooted are u s-off? Either way, try installing a rom of your choice and doing a full wipe to clear out whatever is causing the issue. Maybe try installing new radios/firmware. RUU to newest ota version.
Good luck!
Anthonicia said:
Root doesn't have anything to do with your WiFi. It is highly unlikely anyways. Google how to set up static ip. U can do it right from your phone.
Your router doesn't show up at all or does is try to connect and nothing? Mine tried to connect and nothing. To set up a static ip your phone needs to at least see the router.
If you're rooted are u s-off? Either way, try installing a rom of your choice and doing a full wipe to clear out whatever is causing the issue. Maybe try installing new radios/firmware. RUU to newest ota version.
Good luck!
Click to expand...
Click to collapse
downloaded wifi analyzer, but that doesn't really help me figure out why the wifi will not connect or disconnect properly. As stated in my original post I am rooted, s-on, with unlocked bootloader htc method. this problem is almost exactly the same problem i had my samsung s2 when it first came out. the radio would not wake up after sleeping and the wifi radio was all messed up. In exactly the same way..
once it connects it is ok, but when i leave the house it never disconnects! so when i go out, it does not switch over to the 3g radio, and at that point i have to TURN OFF wifi. When I come back in the house then i have to go through another long process of trying to get it to connect to my wifi again. I did not change ANYTHING after rooting. So it has got to be related to that somehow....it just says. "MWOI0 not in range", but yet it will show 5 others in the neighborhood as being available (all secured like mine).
Does your regular computer/laptop connect to your wifi?
Have you rebooted your router/modem?
We had a power outage/surge one day and the computers connected still had connection, but the items which were disconected (phones left house for work) would not reconnect.
I know it sounds simple, but we spent half an hour figuring out why some devices had wifi and some didn't.
You are seeing neighbors wifi's, that's why I suggest this.
I also noticed this other thread, maybe related,
http://forum.xda-developers.com/showthread.php?t=1691189
There's an app called tasker in play store that allows u to turn on/off wifi by location automatically. It costs a pretty penny, but definitely worth it. The possibilities are exponential with that app.
Look into setting a static ip & change the channel on your router. Give u advice and u don't want to try it. Do u really want it fixed or is it just an annoyance u like to complain about?
Static ip worked for my phone in a similar situation. Up to u to implement the fixes.
Hello
Im a proudly owner of a S3 and a GNexus and I have some problems regarding Wi-Fi, I know that this is not an S3 problem but its and android problem but perhaps someone can help me in here..
the thing is, I have two routers in my house, one is the master one for cable/internet company and the other is and range extender to expand the signal of the wireless lan....
every morning, when I wake up, if I go to the floor where is the first router both my S3 and Gnexus connect successfully to the wireless network and evevyrthing works fine....however if I go to the floor where the bridge/extender is located, both phones detects the wireless network, however can't connect to it, on wireless settings says...Obtaining ip address...and stays there for ages...and nothing...cant connect...for me to connect to the bridge, I have to restart the bridge and both phones connect immediately...
please any ideas??
thanks and best regards,
hugo
HcMAX said:
Hello
Im a proudly owner of a S3 and a GNexus and I have some problems regarding Wi-Fi, I know that this is not an S3 problem but its and android problem but perhaps someone can help me in here..
the thing is, I have two routers in my house, one is the master one for cable/internet company and the other is and range extender to expand the signal of the wireless lan....
every morning, when I wake up, if I go to the floor where is the first router both my S3 and Gnexus connect successfully to the wireless network and evevyrthing works fine....however if I go to the floor where the bridge/extender is located, both phones detects the wireless network, however can't connect to it, on wireless settings says...Obtaining ip address...and stays there for ages...and nothing...cant connect...for me to connect to the bridge, I have to restart the bridge and both phones connect immediately...
please any ideas??
thanks and best regards,
hugo
Click to expand...
Click to collapse
Is it password protected? If so try making it 'open' or change the encryption type.
Skander1998 said:
Is it password protected? If so try making it 'open' or change the encryption type.
Click to expand...
Click to collapse
Hi,
first thanks for the quick reply,
yes the network is password protected...I changed the encryption type for the WPA not the WPA2 and the problem still persists...
the thing that kills my brains is that, to connect to the bridge I must restart the the access point every morning,....
thanks
Do you have DHCP enabled on the 2nd router?
larryk said:
Do you have DHCP enabled on the 2nd router?
Click to expand...
Click to collapse
yes, I guess so....., should DHCP be enabled or disabled?
sorry but this situation is driving me crazy.....
I cant connect to the brigde/extender network right now with both my android phones and android tablet, however with my laptop running windows 8 I can......
wth??????
this is so frustrating!!!!!
Are you sure the second device extends the main access point and not just create a new WLAN?
Have you updated the firmware of both devices?
What devices do you have?
Am I understanding correctly that your laptop does work even though both Android devices don't (before you reboot the extender)?
Nope...its not creating another wireless lan... it extends the main plan correctly cause my laptop connects perfectly to the Wi-Fi from the extender even prior to the restart of the extender....
The devices are...main router from the ISP- Thomson
Range extender- tp link 701nd
Thanks
Sent from my Galaxy Nexus using xda premium
HcMAX said:
Nope...its not creating another wireless lan... it extends the main plan correctly cause my laptop connects perfectly to the Wi-Fi from the extender even prior to the restart of the extender....
The devices are...main router from the ISP- Thomson
Range extender- tp link 701nd
Thanks
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Both have latest firmware? Might be a bug in the WiFi driver of the AP/ROUTER... or it's in Android.... you will need to test by trial and error I guess...
Ok..
Do you guys know anything if I must have my IP static or dynamic?
Thanks
Sent from my Galaxy Nexus using xda premium
HcMAX said:
Ok..
Do you guys know anything if I must have my IP static or dynamic?
Thanks
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Dynamic would be the friendliest to work with... you could try if it's a DHCP issue by setting a fixed IP when the problem occurs, but I don't think it is.
This is not a problem with the phone(s)....is with the router config. Contact the manufacturer for further assistance...
HcMAX said:
yes, I guess so....., should DHCP be enabled or disabled?
Click to expand...
Click to collapse
If you got a router and a range extender, there's nothing you need to fiddle with because the range extender will just Relay DHCP requests between client and master router.
Two routers* pushing out IP addresses is a no go, there will be a conflict in your scenario, and all range extenders will of course take this into account.
If you had two "real" routers*, it would still be possible to set everything up, although then there's a lot to take into account.
* Router is a inaccurate term used for the consumer grade combination devices. They're in fact a router, a switch, and a wireless access point bundled in a neat package. Sometimes with a xDSL modem or something on the external interface of the router.
Try setting the IP to static and more important, try giving it a default gateway to the routers IP. That should make it easy for your phone to directly look for the gateway it is looking for.
Sent from my Galaxy S3
I have three routers, one main, one extender, one repeater (creating a whole new network for other building). Both main and repeater are the same network. All is config as per DD-WRT documentation. All three have latest DD-WRT.
After trying many things, all I can say is the (or mine at least) S3 always has trouble when many APs are nearby. I don't use VOIP because of that (it could disconnect at any time).
Next step on my list is to have 3 different SSIDs (only two now) and try using tasker to debounce the wifi switching (if that is even possible).