g8x only enters EDL mode. All partitions are gone.
When extracting rawprogram.xml, [!] "Error: extraneous data found IN version" is displayed and extraction fails.
teach me how to ubrick
Hello. I am having the same problem. Did you unbrik your phone?? If yes please tell me solutions thank you
Are you able to enter download mode or does it fastboot loop?
something happened in qfil and now I just go into edl mode that's it the computer doesn't even recognize the phone in anything other than qfil so if anybody has any tips on this I'd love to hear it
bro u all fkd up the partition table...so have to re write...or u can enter 9008 mode by shorting the pins in the motherboard.......for creating a partition table there is some video in YT ig
Related
v300l install rom wrong please help .mbn file can reboot (volume down and hold) only one
can see port lge android net usb serial port and qualcomm hs-usb qdloader 9008
lcd show
if you want to get ram dump please do following action
1)Please connect USB.
2) Get the ram dump image using QPST Configuration.
please prog emmc file
Go to the Frankenstein forum
dami00976 said:
Go to the Frankenstein forum
Click to expand...
Click to collapse
thank you ...
Can not go download mode
lcd show QPST sahara mode
Interesting. Sahara is the protocol that fastboot uses. What happens if you type fastboot devices
@Josh McGrath was telling me that his Moto can be recovered from a 9008 brick using fastboot.
Since the PBL is the only thing that is loaded in 9008 mode, maybe all SD835 phones have that ability now.
EDIT: seriously, this is kind of a big deal. You wouldn't be able to flash unsigned firmware, but you would be able to recover your phone. It also means that ANY of us could recover our phones in the event of a 9008 brick.
Please post the results of plugging your phone into your PC and typing fastboot devices.
-- Brian
Can you put your phone in download mode?
In 9008 QDLOAER mode, the only thing that is loaded is the PBL (Primary Boot Loader) that is contained in the CPU. It is an emergency rescue mode.
In older SnapDragon chips (if the phone used UFS storage), the only thing you could do is use a firehose, and those leaked very rarely. If the phone used eMMC storage, then you could boot from an SD card.
If I am correct, and all SD835 and above chips now load a limited version of fastboot when the phone goes into 9008 mode, then we can do whatever we want to our phones with no risk.
TL;DR: No, you can not get into download mode, NORMAL fastboot mode, or recovery when you phone is in QDLOADER mode.
-- Brian
https://www.google.com/amp/s/forum....0/help/lg-v30-qloader-9008-help-t3808990/amp/
This guy somehow fix his device @runningnak3d
runningnak3d said:
In 9008 QDLOAER mode, the only thing that is loaded is the PBL (Primary Boot Loader) that is contained in the CPU. It is an emergency rescue mode.
In older SnapDragon chips (if the phone used UFS storage), the only thing you could do is use a firehose, and those leaked very rarely. If the phone used eMMC storage, then you could boot from an SD card.
If I am correct, and all SD835 and above chips now load a limited version of fastboot when the phone goes into 9008 mode, then we can do whatever we want to our phones with no risk.
TL;DR: No, you can not get into download mode, NORMAL fastboot mode, or recovery when you phone is in QDLOADER mode.
-- Brian
Click to expand...
Click to collapse
C:\Users\sandking\Downloads\FlashOne2.0\FlashOne2.0\tools>adb devices
List of devices attached
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
C:\Users\sandking\Downloads\FlashOne2.0\FlashOne2.0\tools>fastboot -- Brian
< waiting for device >
:crying::crying::crying:thank you i wait file qpst for you
dami00976 said:
Can you put your phone in download mode?
Click to expand...
Click to collapse
i can not put phone in download mode lcd show qpst saharamode put volume+hold=restart only and can not shutdown
ricohz said:
https://www.google.com/amp/s/forum....0/help/lg-v30-qloader-9008-help-t3808990/amp/
This guy somehow fix his device @runningnak3d
Click to expand...
Click to collapse
thank you. I try to do it. unsuccessful
https://www.img.live/image/9cSvu
Waiting for help.
sandking707 said:
Waiting for help.
Click to expand...
Click to collapse
I think you might need to send to lg at this point for repairs
R800x_user said:
I think you might need to send to lg at this point for repairs
Click to expand...
Click to collapse
thank you.
i buy import Country does not have Help Center.
Edl Mode locked
I've read that in some instances Edl mode isn't accessible via button combo or adb.
I had this happen and thankfully help is at hand.
The Edl tool by @djkuz
Has the answer, Edl tool is here
https://forum.xda-developers.com/axon-7/development/axon-7-edl-tool-flash-backup-restore-t3750759
OK to fix this
Download and install to your PC or laptop
Run this from the root directory drive C: or D:
Make sure all drivers are up to date
Open the app, Run as admin.
Boot your phone into FTM.
Turn your phone off.
Press and hold Vol dn + power till you see the FTM screen.
Plug your phone into PC or laptop and follow the on screen instructions.
Then select unlock > then Edl fix.
Let the app run.
When finished you should have a working Edl again
Just boot into FTM and follow instructions in edltool.No need to use Unlock EDL Fix
Predatorhaze said:
Just boot into FTM and follow instructions in edltool.No need to use Unlock EDL Fix
Click to expand...
Click to collapse
Yes, edl does work via the app. Edl fix is to return the button combo.
Here is a reply from @sToRm1nG thank you
"Thanks for your reply, I stumbled upon your thread before I guess but wasn't sure if this is gonna help me."
"Unfortunately, I am not able to get into FTM..."
"However, I am able to boot into EDL mode, so do you think the EDL fix will also work if I am in EDL mode?"
*EDIT*
"I tried it and it worked!"
"Thank you so much for your input!"
Click to expand...
Click to collapse
Hopefully this can help others
Hoping for help here. In trying to root this phone, having successfully unlocked bootloader, I am trying to flash back to stock firmware (as rooting went less than well!)
Couldn;t get the MSM download tool to work, so thought I would try the fastboot zip file extraction method!
The only Oxygen OS I can find that has the flash all .bat file is
10.5.5-GLOBAL-NordOxygen_14_OTA_007_all_2008180221_c45e1d5febd1f-FASTBOOT
Which results in looking like its working within cmd with all fastboot instruction seemingly writing to phone. But upon reboot, it just goes back to the qualcomm crashdump screen....!!
Grateful for any help inc getting the MSM download tool working.
Many thanks all
> 10.5.5-GLOBAL-NordOxygen_14_OTA_007_all_2008180221_c45e1d5febd1f-FASTBOOT
It this from Oneplus Nord ? That cannot work on N10 of course.
Qualcomm EDL mode should always work and is your best way to recover the phone.
andreas__ said:
> 10.5.5-GLOBAL-NordOxygen_14_OTA_007_all_2008180221_c45e1d5febd1f-FASTBOOT
It this from Oneplus Nord ? That cannot work on N10 of course.
Qualcomm EDL mode should always work and is your best way to recover the phone.
Click to expand...
Click to collapse
But whats does Qualcomm EDL mode actually look like? A blank screen? Can't find an explanation as to what the screen shows on Qualcomm EDL mode
TheDon13 said:
But whats does Qualcomm EDL mode actually look like? A blank screen? Can't find an explanation as to what the screen shows on Qualcomm EDL mode
Click to expand...
Click to collapse
yes it is a black screen! You know that is in EDL mode when you look into the "Device Manager" in Windows. Further explanation on how to use the tool is in the respective thread https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4204445/.
andreas__ said:
yes it is a black screen! You know that is in EDL mode when you look into the "Device Manager" in Windows. Further explanation on how to use the tool is in the respective thread https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4204445/.
Click to expand...
Click to collapse
Nowhere does it say EDL mode is simply a blank (as if phone off!) screen btw.....
I always press start on msm tool first then either adb reboot edl or make sure phone is off then hold volume buttons
I'll cut to the chase, I have a Nokia 1.3 and it is in edl mode (9008) due to bad flashing, the story is as follows. I tried to flash using the fastboot command and I had everything ready, the ROM, minimal AND fastboot, etc, and it occurred to me when I didn't know how to flash the partitions .. download the file "flash-all.bat" from the internet and at the end I ran it .. and so I left the device in the state I am in, rather in (900E) then I managed to change or go to Qualcomm 9008 mode. I would like to know if there is a way to get the phone back or not, thank you.
Hi everyone, I bought this phone working from second hand but the seller told me he tried to unlock the bootloader without success and the phone still loose the fingerprint sensor, so I decided to unlock the bootloader successfully following THIS thread and made a downgrade to Android 9 according to THIS other tutorial hopping to get it work again but I wasn't able to do it, so I decided to just use LGUP to install the same Android 12 that I had but the problem started at this point because once the KDZ was installed successfully, the deviced got a bootloop but I still was able to get into EDL, Fastboot and Download Mode, so I tried the steps from THIS other thread to unbrick it but it got even worse at this point, I flashed all the abl, xbl, etc. partitions and the "rawprograme files" via QFIL and then the phone won't even gave any life signals. I contacted someone that some months ago had the same problem and he told me that I could get into EDL by short pining the test point on the motherboard, which actually worked, so I extracted the KDZ Android 9 rom that I flashed in the first place to get the original abl, xbl, etc. partitions that I crossflashed from a v50 (Which I downloaded from the corresponding thread for unbrick), in other words I flashed the same partitions with the correct v50s files instead other model ones. So now this is where I'm right now, the phone don't turns on at all but when I connect it to the PC it gets recognized as LGE Android Platform USB Serial Port (COM11) and the buttons combinations don't work at all, so still can't get into Download mode by any method or even turn off the device, but I still can disconnect the battery and short pin the Qualcomm 9008 mode to use QFIL.
Would someone please be so kind of telling me how could I recover the Download Mode to use the COM4 and COM5 ports to flash the phone via LGUP?. According to THIS other thread, I could get the correct XML "rawprograme files" for my device (which I crossflashed with the v50) from a KDZ using some tools and Python, but I have to be honest: I DON'T KNOW HOW, even with the step by step tutorial.
At this point I think this would be the right step, to flash all the original files for my model and get the Download Mode back to be able to flash the KDZ rom via LGUP and update via OTA to Android 12 again to avoid the bootloop problem.
try to reflash(QFIL method) modified abl should get the download mode back
darrelama said:
try to reflash(QFIL method) modified abl should get the download mode back
Click to expand...
Click to collapse
Thanks for replying, but I have some questions:
1. The abl file you mean is the engineering one? And...
2. Would you be so kind of telling me how to flash via QFIL? I've seen that it's possible but as far as I know, I need a specific type of rom files to do it, and I don't know how to convert a KDZ or where to download a QFIL ROM.
Thanks!
iMarzateD said:
Thanks for replying, but I have some questions:
1. The abl file you mean is the engineering one? And...
2. Would you be so kind of telling me how to flash via QFIL? I've seen that it's possible but as far as I know, I need a specific type of rom files to do it, and I don't know how to convert a KDZ or where to download a QFIL ROM.
Thanks!
Click to expand...
Click to collapse
yes, engineering one mentioned here （THIS）
QFIL>Tools > Partition Manager
read abl_a and abl_b to backup then load abl engineering file to both
basically the same steps up to the following:
"Go back to Partition Manager and right click on abl_a again then select Manage Partition Data, then Select Load and choose the abl engineering file.
Do the same for abl_b."
then try download mode
darrelama said:
yes, engineering one mentioned here （THIS）
QFIL>Tools > Partition Manager
read abl_a and abl_b to backup then load abl engineering file to both
basically the same steps up to the following:
"Go back to Partition Manager and right click on abl_a again then select Manage Partition Data, then Select Load and choose the abl engineering file.
Do the same for abl_b."
then try download mode
Click to expand...
Click to collapse
Hello again, already tried flashing the engineering abl but I still can't get into download mode. The phone keeps off the whole time and by plugging in the USB cable, no matter what button combination, the PC always recognizes it as the same LGE Android Patform USB Serial Port (COM11), the only other state of the device is the Qualcomm 9008 by pinning the motherboard. This specific COM11 state never was able to flash anything by PC, I don't know what actual mode is, but when I was able to set the devide in Download Mode the PC always showed 2 devices in the Device Manager, the COM5 and the COM4, that way I knew I was able to use the LGUP to flash. I'm thinking that I'm not setting the phone on the correct state to flash by any method, but since the buttons seems not to work, I don't know how could I do it.
While on this mode "LGE Android Patform USB Serial Port (COM11)", try to hold both power and vol- for some seconds until the "LGE Android Patform USB Serial Port (COM11)" disappear from your PC device manager and immediately release both and now hold vol+ button to get into download mode.
You can do it while on the 9008 mode too though.
Maybe that can help.
I have LUNs backup for v50s but I can't upload it due to my internet plan quota limit.
ardian1899 said:
While on this mode "LGE Android Patform USB Serial Port (COM11)", try to hold both power and vol- for some seconds until the "LGE Android Patform USB Serial Port (COM11)" disappear from your PC device manager and immediately release both and now hold vol+ button to get into download mode.
You can do it while on the 9008 mode too though.
Maybe that can help.
I have LUNs backup for v50s but I can't upload it due to my internet plan quota limit.
Click to expand...
Click to collapse
Thanks, I'll try that for sure to see if I can get into the Download Mode or something. I would appreciate so much if you could share your backup, since I think I could restore the whole firmware with it, but I don't have any experience on the "LUNs" tho. I'm any case, I don't have too much time every week to give it a try, so I hope tomorrow I could test the combo you say.