Question Gagal flashing redmi note 10 (mojito/sunny) - Redmi Note 10

Is there anyone here who can help solve my problem on redmi note 10 that can't go back to the default firmware it always fails every time it flashes via fastboot or edl mode even though before what makes me more confused when I install a miui-based room it always boots up and doesn't want to turn on to the homescreen but when i install the android 12 based aosp room it can work normally even though i have a problem with the sensor and when i try to flash again to miui it turns out i'm having a bootloop again as a result I can only install room aosp is there a solution for me to go back to the miui-based room?

---

I would first try switching the active phone slot after the Miui flash as the easiest. In fastboot mode, type fastboot --set-active=a from your computer If Miui won't boot after reboot, then try fastboot --set-active=b

---

Hi
Often flashing fastboot roms with Mi flash tool get you error messages. to skip these issues.
• You need just to select "Save user data" option then click on "Flash"
• Once flashing completed and your device rebooted hold the volume up button so you can access the Mi recovery, once you there select "Wipe data" and confirm the wiping when formating done reboot to system.
Regards

---

I've done all that but can't solve the problem I'm facing

---

Proceed as follows.:
- Download the Miui ROM in fastboot format to your PC and extract the file
- Download the flash firmware tool - "MiFlash20181115" to your PC and extract it
- Run MiFlash and enter the path to the extracted firmware
- Turn off the phone and start fastboot mode
- Connect the phone to the PC and select "refresh" in MiFlash - you should then see the phone code (88acc400) in the "device" column
- Select "clean all" at the bottom
- Start the "flash" option and wait until the phone reboots itself (it takes a long time) - if you get an error you will see "false" in the "result" column, otherwise wait.

---

StaryMuz said:
Proceed as follows.:
- Download the Miui ROM in fastboot format to your PC and extract the file
- Download the flash firmware tool - "MiFlash20181115" to your PC and extract it
- Run MiFlash and enter the path to the extracted firmware
- Turn off the phone and start fastboot mode
- Connect the phone to the PC and select "refresh" in MiFlash - you should then see the phone code (88acc400) in the "device" column
- Select "clean all" at the bottom
- Start the "flash" option and wait until the phone reboots itself (it takes a long time) - if you get an error you will see "false" in the "result" column, otherwise wait.
Click to expand...
Click to collapse
I've done as you suggested I managed to do flashing but my cellphone is still bootloop even though I have successfully flashed it and I have formatted the data too but it still doesn't want to go to the homescreen always stuck in the MIUI boot animation is there any other way i can do it?

---

Did you flash the phone with MiFlash and it booted itself without any further intervention from you?

---

Min- said:
I've done as you suggested I managed to do flashing but my cellphone is still bootloop even though I have successfully flashed it and I have formatted the data too but it still doesn't want to go to the homescreen always stuck in the MIUI boot animation is there any other way i can do it?
Click to expand...
Click to collapse
Back to recovery in that point then wipe data and reboot.

---

Saya sudah flash berkali-kali tapi tetap tidak bisa menghidupkan perangkat saya sudah gonta ganti versi miui tapi tetap saja menghapus/memformat data setiap selesai flashing tapi tetap gagal menghidupkan hp saya tapi anehnya setiap kali saya install customroom berbasis AOSP perangkat saya bisa nyala, yang bikin aneh Flashing room miui selalu bootloop, entah itu firmware bawaan atau customrom, masih stuck di animasi miui

---

Jadi saya bingung harus gimana biar bisa install miui lagi di device saya Padahal mau rilis miui 13 Tolong bantu saya

---

StaryMuz said:
Apakah Anda mem-flash telepon dengan MiFlash dan mem-boot sendiri tanpa intervensi lebih lanjut dari Anda?
Click to expand...
Click to collapse
Ya pas flashing berhasil restart sendiri Tapi tetep stuck di animasi miui dan gak mau masuk homescreen padahal udah di format data lewat recovery tetep bootloop

---

There is a rule to write exclusively in English. My native language is Czech.
You shouldn't have done any data formatting or run a recovery.

---

StaryMuz said:
Ada aturan untuk menulis secara eksklusif dalam bahasa Inggris. Bahasa ibu saya adalah Ceko.
Anda seharusnya tidak melakukan pemformatan data atau menjalankan pemulihan.
Click to expand...
Click to collapse
Ya pas flashing berhasil restart sendiri Tapi tetep stuck di animasi miui dan gak mau masuk homescreen padahal udah di format data lewat recovery tetep bootloop

---

Min- said:
Ya pas flashing berhasil restart sendiri Tapi tetep stuck di animasi miui dan gak mau masuk homescreen padahal udah di format data lewat recovery tetep bootloop
Click to expand...
Click to collapse
Min- said:
Ya pas flashing berhasil restart sendiri Tapi tetep stuck di animasi miui dan gak mau masuk homescreen padahal udah di format data lewat recovery
Click to expand...
Click to collapse

---

I formatted the data because after flashing it couldn't boot after I waited for hours, so I formatted the data but the result is still the same

---

In this case, it looks like a hardware error. Can you take a screenshot of the PC screen when the phone reboots and MiFlash is still on the screen?

---

I can't take videos or pictures When I flash my cellphone because I only have one cellphone and it's no longer there for recording videos or taking pictures

---

I just remembered Indeed, before experiencing death or bootloop My gyro sensor is having problems And after I install room aosp now After I installed the sensor box application on the play store After I checked, it's true that my gyro was not detected Is it possible that my gyro hardware is dead But does it matter if the gyro dies, does it affect miui-based rooms?

---

On the PC, take a screenshot using the "Print Screen" button on the keyboard. The image is saved to the clipboard and from there you have to insert it into a document or photo editor directly into the image.
The gyroscope error may be based on another hardware error. However, there is no reason for the whole process of flashing the default ROM to run correctly and the phone not starting.

---

So, what should I do If it's just to take a screenshot, I have to re-flash I'm a little hesitant Because of this I have installed room aosp So if I re-flash miui I have to reinstall the aosp rom bro If it's a flashing step problem I'm sure I've done it right Because I've done that before and it worked Because before, every time I experienced an error in my custom room, I always handled it by flashing But the question is what causes my cellphone this time to fail to boot every time I install the MIUI room While I installed an aosp-based room, it can always turn on even though the gyro sensor can't be used