Related
This guide shows how to install TWRP and Magisk even starting from firmwares after B19 A2017U firmware (starting B25, ZTE removed Fastboot). As always read the ENTIRE directions before beginning. If you'd like to try a faster method, see instead King1990's Alternate Method posted below steps A, B and C.
Step A involves downgrading your OS to B19. If you are on B25 or higher currently, you must not skip this step. If you are on B19, skip this step.
Step B is upgrading to B32 on an unlocked system, retaining Fastboot and the Recovery by using DrakenFX's method.
Step C is installing Magisk.
STEP A: FLASH TO B19 WITH TWRP USING EDL MODE
NOTE: This assumes you are unlocked. If you need to unlock starting from a firmware later than B19, please follow the EDL Unlock instructions at the EDL Thread, or use the Axon7Toolkit unlock, which is essentially the same but may be easier for some.
1. Install MiFlash using the EDL thread
2. Install the QUALCOMM drivers linked in the same thread.
3. Download "B19-NOUGAT_FULL (Nougat 7.1.1)" from the same thread.
4. Extract the ZIP file.
5. Open MiFlash, select the named sub-folder from the ZIP
6. Connect Axon 7 via a USB cable, and hold VOL-UP/VOL-DOWN/POWER until the screen goes black and the red notification LED blinks very intermittently (~1 time per 4 seconds) to get it in EDL mode.
7. Hit Refresh in MiFlash and confirm device is shown in list.
8. Hit Flash in MiFlash to flash it. (This rolls back your device to B19 stock)
9. Repeat Steps A.3-A.8 for "B19-NOUGAT_TWRP (Nougat 7.1.1)," found in the same EDL thread (to get TWRP).
10. After EDL flashing B19-NOUGAT_TWRP (Nougat 7.1.1), hold Power+VolUp when boot into TWRP. At the first warning screen, slide to allow modifications, but DO NOT BOOT INTO THE ROM until you complete the next step re: no-verity.
11. Tap Mount, and then Mount the phone via MTP in TWRP. Transfer over the latest (5.1 at time of writing) no-verity-opt-encrypt-5.1.zip file from this link (original thread) to your phone via MTP. Flash this file using the "Install" command in the TWRP main menu.
Troubleshooting Notes:
If bootup freezes at the very first screen after the ZTE logo ("Start - Continue to Boot..."), you probably have either (1) not properly flashed the B19 FULL before the TWRP folder, or (2) enabled changes in TWRP without flashing the zip in Step 11. If so, start over from the beginning, reinstall B19 FULL and TWRP via EDL. If you cannot boot into the system, this is likely your only option.
If you are stuck on a bootup screen that says "To start android, enter your password": You have probably mistakenly started a normal boot after flashing the B19 FULL but before flashing TWRP. Do not attempt to enter a password, simply get back into EDL mode to flash the TWRP folder for Step A.9. Do this by either holding VOL+/VOL-/POWER, or by using the ADB command if available, "adb reboot edl" . If you are in-between steps and having trouble finding a part of the boot sequence that ADB receives commands, try opening an ADB console on Windows and entering "adb devices -l" to see if your device is visible to ADB at either the bootloader itself (VOL+/POWER), or the main root TWRP screen. (Worst case, if TWRP is not installed, but if you can access Fastboot, put the TWRP .img file in the same directory on your PC as your ADB/Fastboot .exes, rename to "recover.img" and use the command "fastboot boot recovery.img" to temporarily boot into TWRP.)
If MiFlash cannot flash to your device even when it can see your device: If you can access ADB, try the command "adb reboot edl" . Some Axon 7 phones apparently do not correctly enter EDL mode when holding VOL+/VOL-/POWER, and although visible to MiFlash cannot be flashed unless a software command puts the phone into EDL. Alternatively, Axon 7 Toolkit can do this - select Option 10 when ADB is active.
If you follow this guide and receive a ctsProfile mismatch error when running a SafetyNet check in Magisk, you likely had some remnant of a prior SU installation that is triggering the error. Please follow the steps in this troubleshooting guide: https://android.gadgethacks.com/how-to/magisk-101-fix-safetynet-cts-profile-mismatch-errors-0178047/
STEP B: UPDATE TO B32
Important: You cannot use the update process in Mifavor to update, or you will lose fastboot. Instead, any updates must be flashed via TWRP.
1. Go to DrakenFX's thread and follow the instructions. Relevant portion added below for simplicity.
2. Download and move to your phone (Internal or SD):
- A2017UV1.1.0B32_bootstack_by_DrakenFX.zip
- A2017UV1.1.0B32_StockSystem_by_DrakenFX.zip
3. Boot into TWRP, and Wipe Cache, Dalvik, and Data
4. Flash ("Install" in TWRP) A2017UV1.1.0B32_bootstack_by_DrakenFX.zip, then install A2017UV1.1.0B32_StockSystem_by_DrakenFX.zip.
5. Flash the no-verity-opt-encrypt-5.1.zip file again from this link (you should already have this on your phone from Step 1 above)
STEP C: INSTALL MAGISK ZIP VIA TWRP
NOTE: If you have performed this with the 13.6 Beta per my earlier guide, simply download Magisk 14.0 within the Manager app and then flash 14.0 in TWRP to update. For new installations, flashing directly the 14.0 ZIP file should be fine. Any Magisk before 13.6 Beta will likely no longer work.
1. This guide assumes you have a clean image with NO SU. (If you have used SuperSU or another SU, you will need to either reset/reflash a clean image, or uninstall it sufficiently. If you have a prior Magisk, there is a Magisk Uninstall tool (here You can proceed without flashing a clean image using that tool, included in Step 3b below.)
2. Download the latest Beta Magisk ZIP file ("Magisk-v14.0.zip") in the main Magisk thread. I have also attached it to this thread for convenience. NOTE that this ZIP file also automatically installs Magisk Manager, so you do not need to download or install it separately in Android.
3. Go to TWRP, and install the Magisk-v14.0.zip. Clear Dalvik/Cache after install.
4. Reboot into stock, and open Magisk Manager which should be installed now automatically. Magisk Hide should be auto enabled, MagiskSU 14.0 should be installed, and all checks should pass including SafetyNet. Catch all the Poke-mans and Pay all the Androids.
Please make a TWRP backup before attempting, and be ready to roll back if needed.
Alternate Method (Thanks to King1990)
This method may be quicker, so you may prefer to try this method first, or as an alternate if the above method is too complex or doesn't work for you:
*these steps only if you are already unlocked your bootloader first UNLOCK *
*Note: it does not matter if your on stock B25 or B32 or any custom roms just follow the steps below*
*Backup first*
1- Download & install Axon7toolkit 1.2.1,install drivers & ADB from the tool (option 1).
2- using the tool, choose option 11 & follow the instructions to flash "A2017U_B19-NOUGAT_FULL_EDL" using Miflash (Axon7toolkit will start Miflash)
3- if the flashing was successful reboot your phone
4- now update using OTA to B25 then again update to B32 through OTA .
5- now you have completely stock B32 , you will also lose fastboot command
6- Reboot to EDL
7- Start Miflash directly it should be here "C:\Program Files\Xiaomi\MiPhone" & Click on refresh , a COM port should appear
8- in the target white bar, paste this destination "C:\Axon7Development\Axon7Toolkit\miflash\unlock\FASTBOOT_UNLOCK_EDL_N" & click flash, if succeed reboot & you should now have fastboot commands
9- again use Axon7toolkit & choose option 9 to flash TWRP , follow the instruction and you should have TWRP.
10- start the system then reboot to recovery and flash magisk 14.0 check for safety net if fails just reboot your phone & it will pass.
11- done.
Previous threads and guides
(Previous Thread)
-----------
(Previous Magisk and OTA process - DO NOT USE)
STEP 2: INSTALLING MAGISK 13.2 WITH ROOT AND SAFETYNET PASS
1. This guide assumes you have a clean image with NO SU. (If you have SuperSU or another SU, you will need to either reset/reflash a clean image, or uninstall it sufficiently. If you have a prior Magisk, there is a Magisk Uninstall tool. You can proceed without flashing a clean image using that tool, included in Step 3b below.)
2. Enable Settings->Security->Unknown Sources in stock.
3. Download Magisk Manager 5.0.6 and Magisk 13.2 (here, and attached for convenience), and copy them to your device. (Note that you can also just install Magisk Manager 5.0.6 and download the latest Magisk flashable ZIP from there.)
(3b. If you already have a prior Magisk & Manager installed, also download Magisk Uninstall (here, attached for convenience) and copy it to your device. Boot into TWRP, and "Install" (flash) Magisk Uninstall. Boot into system, and uninstall Magisk Manager. Clear Dalvik/Cache after each step.)
4. Install Magisk Manager v5.0.6 via File Manager direct as an APK.
5. Go to TWRP, and install the Magisk 13.2.
6. Reboot into stock, and open Magisk Manager. You should see both Magisk and Root installed (Root as "Magisksu"). If you try SafetyNet right now, it will fail.
7. Go into Settings in Magisk Manager and enable MagiskHide.
8. Reboot into TWRP, and flash the Magisk 13.2 SafetyNet Fix, attached. Reboot.
9. Now if you check SafetyNet, it should pass.
STEP 3: GET OTAS (EXPERIMENTAL)
There are still issues with B19 to B25 upgrades with Magisk using OTA packages, (such as those by DrakenFX).
Prior to the SafetyNet update (Magisk 13.0 beta), users reported partial success - if they installed Magisk successfully on B19, and gave root permission as needed, they could upgrade to B25 and retain old root permissions but NOT add new permissions for apps. I have not seen it tested whether this is still true after the SafetyNet update (Magisk 13.2).
----------
(Previous Original Guide - DO NOT USE)
If you are only here for Magisk: Despite all the horror trying to get it to work with 12.0 and earlier versions, it should flash fairly easily using versions later than the 20170520 beta and 13.0 beta Magisk Manager.. But since the 20170520 files are the only version I've tested, I can only vouch for those files and they are specifically mentioned in the guide.
NOTE: This assumes you are starting at B25, but the instructions should work for any B version number, since MiFlash is going to force us to B19.including how to install Magisk successfully - only new beta versions will install, and I've only tested the 20170520 build with Magisk 13.0 beta, but it worked entirely as intended. Below are the steps needed, and below that is my old post (hidden) for posterity in case it helps troubleshoot later if something breaks.
STEP 1: FLASHING FROM B25 TO B19 USING EDL MODE:
1. Install MiFlash using the EDL thread
2. Install the QUALCOMM drivers linked in the same thread.
3. Download "B19-NOUGAT_FULL (Nougat 7.1.1)" from the same thread.
4. Extract the ZIP file.
5. Open MiFlash, selected on the named sub-folder from the ZIP
6. Connect Axon 7 via a USB cable, and hold VOL-UP/VOL-DOWN/POWER until the screen goes black and the red notification LED blinks very intermittently (~1 time per 4 seconds) to get it in EDL mode.
7. Hit Refresh in MiFlash and confirm device is shown in list.
8. Hit Flash in MiFlash to flash it. (This rolled back my B25 device to B19 stock)
9. Then do the same process again with "B19-NOUGAT_TWRP (Nougat 7.1.1)," found in the same EDL thread (to get TWRP). ALTERNATIVELY, you can use the Toolkit to install TWRP, or via ADB, or any other method.
Note that first I just downloaded the TWRP version, and TWRP successfully installed and I could boot into TWRP, but it would totally freeze before loading the OS ROM every time. You MUST flash the B19 FULL first to avoid this.
Also, if any of these steps fail, install the Toolkit and use the same operations in the Toolkit. I used v. 1.2.0 for both the EDL flashing and to install TWRP as well, since on a later A2017U, the button restart method appeared to put me in a halfway-EDL mode which was visible from MiFlash, but did not allow flashing. In that case, a software EDL reset ("adb reboot edl" or "reboot edl" in the TWRP console) was the only way to get MiFlash to allow it to flash. The Toolkit does this nicely.
STEP 2: INSTALLING MAGISK 13.0 BETA WITH ROOT AND SAFETYNET PASS
1. Make sure you have a clean image with NO SU (PHH or MagiskSU or otherwise), and NO Magisk/Magisk Manager installed.
2. Enable Settings->Security->Unknown Sources in stock.
3. Download Magisk Manager 20170520 13.0 beta and Magisk 20170520 (here, and attached for convenience) (full beta thread here if needed), and copy them to your device.
4. Install Magisk Manager 20170520 13.0 beta via File Manager direct as an APK.
5. Go to TWRP, and install the Magisk 20170520 beta (here, and attached for convenience)
6. Reboot into stock, and open Magisk Manager 13.0. You should see both Magisk and Root installed (Root as "Magisksu"). If you try SafetyNet right now, it will fail.
7. Go into Settings in Magisk Manager and enable MagiskHide.
8. Now if you check SafetyNet, it should pass.
Note that the temporary beta builds appear to only be available for a short time, so either use the files attached, or go ahead and try the latest beta build. The first build I tried, 20170520, worked. Again, my guess is all beta builds or full builds after 20170520 will work with the instructions above, but feel free to test.
STEP 3: GET UPDATES / GO TO B25: I have not tested yet to ensure Magisk doesn't break, but I believe you should be able to download OTA packages, such as those by DrakenFX and flash them. However, users are reporting some bugs upgrading beyond B19, so OTAs are a work in progress. Please make a TWRP backup before attempting this and be ready to roll back if needed.
6bolt2g reports he had success moving from B19 (rooted) to B25, with the following steps: (a) flash "the DrakenFX B25 flashable zip's and the no-verity zip to keep TWRP"; and (b) follow STEP 2 above. However, 6bolt2g and StickMonster report that after upgrading to B25, you may experience problems with adding apps not previously whitelisted. Again, this is not verified by me but reporting it in the first thread for convenience.
For now, applying OTAs beyond B19 should be considered experimental - please be aware of the risk and have a backup before trying, and share your results here.
Changelog
Edit 5/21/2017: Added additional steps to Magisk to show process after flashing in TWRP.
Edit 5/23/2017: Added 6bolt2g report re: moving from B19 to B25.
Edit 5/24/2017: Added additional updates re: OTAs.
Edit 7/17/2017: Revised based on new ~7/12 Google SafetyNet changes, new Magisk from 5/15, and SafetyNet fix
Edit 9/3/2017: Added additional alternate solutions and troubleshooting advice.
Edit 9/4/2017: Revised process for B32, Magisk 13.6 Beta.
Edit 9/10/2017: Revised process for Magisk 14.0.
Edit 9/17/2017: Added King1990's alternate method.
Just wanted to thank you for the guide. Now I'll be able to get root on B25.
EDIT: I just wanted to know if flashing the B19_full will wipe userdata? I have a feeling it does, but I just want to double check.
Sent from my ZTE A2017U using XDA-Developers Legacy app
troy5890 said:
Just wanted to thank you for the guide. Now I'll be able to get root on B25.
EDIT: I just wanted to know if flashing the B19_full will wipe userdata? I have a feeling it does, but I just want to double check.
Click to expand...
Click to collapse
When I did it, it did NOT wipe userdata. Surprising to me that all my apps and things were still on the screen, but the version did indeed roll back. YMMV.
I've played with Magisk 13 too. I could get root, but not safety net. That's on b25. I can't remember if I tried it on b19.
To get safety net and Magisk 10 working on b25 I have to get it working on b29 and then upgrade to b25. So what you suggest for 13 sounds promising.
I'll have to play some more if you got it working on b19.
Curious, what makes you think OTAs will work? B25 removes fastboot for me and installed stock recovery. I had magisk working on B25 when not updating the bootsect and keeping that at B19.
Second question, with only B19 installed, after rolling back from B25 do you, or anyone for that matter have a problem where the signal constantly cycles on/off?
StickMonster said:
I've played with Magisk 13 too. I could get root, but not safety net. That's on b25. I can't remember if I tried it on b19.
To get safety net and Magisk 10 working on b25 I have to get it working on b29 and then upgrade to b25. So what you suggest for 13 sounds promising.
I'll have to play some more if you got it working on b19.
Click to expand...
Click to collapse
Magisk 10.3-beta2 worked after simply flashing the zip and the superuser and manager apks for me on b19
I was on rooted B19 (super su) and I used the DrakenFX B25 flashable zip's and the no-verity zip to keep TWRP. Then booted into the OS to put the Magisk manager on following 'STEP 2' in the OP then flashed the Magisk zip in TWRP and all seems to be working. I will do a full test drive today and report back if any issues. So far I have root and pass safety net checks and android pay let me open it up and set it up.
6bolt2g said:
I was on rooted B19 (super su) and I used the DrakenFX B25 flashable zip's and the no-verity zip to keep TWRP. Then booted into the OS to put the Magisk manager on following 'STEP 2' in the OP then flashed the Magisk zip in TWRP and all seems to be working. I will do a full test drive today and report back if any issues. So far I have root and pass safety net checks and android pay let me open it up and set it up.
Click to expand...
Click to collapse
Nice. Looking forward to hearing those results.
crashnova said:
Nice. Looking forward to hearing those results.
Click to expand...
Click to collapse
So far the masking function ie. Android Pay worked today when I went to use it. I went to use a few root apps, ES File Explorer and just an emoji switcher this afternoon and it was force closing the Magisk app. I tried to restart the phone to see if that was some of the issue, no difference. I also tried to uninstall and install the app from the Play Store, but it was an older version (v12). So I removed it and put the v13 back on and the force closes have stopped for now. I will have to continue using it to see how it goes. Anyone have any suggestions for root apps they would like me to try? With all the goodies baked into these stock roms there is less and less need for root access, at least for me.
6bolt2g said:
I was on rooted B19 (super su) and I used the DrakenFX B25 flashable zip's and the no-verity zip to keep TWRP. Then booted into the OS to put the Magisk manager on following 'STEP 2' in the OP then flashed the Magisk zip in TWRP and all seems to be working. I will do a full test drive today and report back if any issues. So far I have root and pass safety net checks and android pay let me open it up and set it up.
Click to expand...
Click to collapse
Thanks! I will update the original post with your results.
Edit: Can you confirm exactly which ZIP files you flashed, and where you specified "no-verity"?
Dodgexander said:
Curious, what makes you think OTAs will work? B25 removes fastboot for me and installed stock recovery. I had magisk working on B25 when not updating the bootsect and keeping that at B19.
Click to expand...
Click to collapse
I figure that as long as you can keep TWRP, the fact that Magisk was updated and confirmed to work with one version of Nougat suggested it should work with minor updates. (Nougat seems to be what broke Magisk initially.) I understand DrakenFX allows flashing in a way that preserves TWRP, so infer that it will likely work. I'm trying not to overstate what I know, but it appears to work for at least 6bolt2g. However, upgrading to B25 should be considered experimental at this point.
Dodgexander said:
Second question, with only B19 installed, after rolling back from B25 do you, or anyone for that matter have a problem where the signal constantly cycles on/off?
Click to expand...
Click to collapse
I haven't had that issue rolling back from B25. Maybe clear caches? Try reflashing with MiFlash?
ScaryBugThing said:
Thanks! I will update the original post with your results.
Edit: Can you confirm exactly which ZIP files you flashed, and where you specified "no-verity"?
Click to expand...
Click to collapse
I already was unlocked and had TWRP installed and I was on Stock B19 with root via Super SU, but the root part shouldn't matter.
I flashed the stock Bootstack and B25 Rom from this post: B25 TWRP Flashable
His directions mentioned using the vm-verity zip file if you want to keep TWRP and not flash super SU. He did not link the verity zip that I saw, so I searched XDA for them.
The link to the TWRP post with the download link: TWRP dm-verity Half way down the first post.
And the direct link to the download file list : no-verity download link I just picked the newest version.
Hope that helps.
*Edit*
To add to my issue earlier about the Magisk Manager crashing when approving root access. After re-installing it seems to work fine. I believe its after a reboot, it starts to have the crashing problem. It does seem to maintain previously approved root accesses though. For example, ES File manager is still able to explore system folders during the crash, because I approved it earlier when it was still working. I'm no programmer so I do not have a clue what is going on. I imagine, something is not persisting through the reboot. And to clarify, it is crashing when new programs are asking for root access and the pop-up shows.
Same for me using the 170523 build. Everything works at first, including root for apps already whitelisted from before the b25 upgrade, but once you try to add a new app to your root list you get FCs from then on any time su tries to run, including trying to start superuser from within Magisk manager. If you delete Magisk data, from twrp or Android app settings, the FCs stop but then you have no apps with root granted.
It looks like there is a version from nfound we should try.
Yep tried miflash running back to b19 and it's the same. I can't run b19 stock anymore, but it's off topic here so I'll shut up
Dodgexander said:
Yep tried miflash running back to b19 and it's the same. I can't run b19 stock anymore, but it's off topic here so I'll shut up
Click to expand...
Click to collapse
If you flash back to b19 try erasing Magisk data. I'm pretty sure that worked for me.
StickMonster said:
If you flash back to b19 try erasing Magisk data. I'm pretty sure that worked for me.
Click to expand...
Click to collapse
Magic is no problem on B19, signal is not. Flashing on and off like the phone is detecting a modem one sec and the next not.
Thanks for the updates about moving to B25. Updated first post - if you test anymore, please share.
ScaryBugThing said:
Hi all - this thread originated in the Q&A forum (old thread), but since I mapped out steps in a guide, I am posting it here since it is the more proper place for it.
This is a guide showing how to get TWRP installed, Magisk running, and I plan to update once I confirm OTAs can be flashed.
If you are only here for Magisk: Despite all the horror trying to get it to work with 12.0 and earlier versions, I believe you should be able to flash it fairly easily using versions later than the 20170520 beta and 13.0 beta Magisk Manager, see links below. But since the 20170520 files are the only version I've tested, I can only vouch for those files and they are specifically mentioned in the guide.
NOTE: This assumes you are starting at B25, but the instructions should work for any B version number, since MiFlash is going to force us to B19.including how to install Magisk successfully - only new beta versions will install, and I've only tested the 20170520 build with Magisk 13.0 beta, but it worked entirely as intended. Below are the steps needed, and below that is my old post (hidden) for posterity in case it helps troubleshoot later if something breaks.
STEP 1: FLASHING FROM B25 TO B19 USING EDL MODE:
1. Install MiFlash using the EDL thread
2. Install the QUALCOMM drivers linked in the same thread.
3. Download "B19-NOUGAT_FULL (Nougat 7.1.1)" from the same thread.
4. Extract the ZIP file.
5. Open MiFlash, selected on the named sub-folder from the ZIP
6. Connect Axon 7 via a USB cable, and hold VOL-UP/VOL-DOWN/POWER until the screen goes black and the red notification LED blinks very intermittently (~1 time per 4 seconds) to get it in EDL mode.
7. Hit Refresh in MiFlash and confirm device is shown in list.
8. Hit Flash in MiFlash to flash it. (This rolled back my B25 device to B19 stock)
9. Then do the same process again with "B19-NOUGAT_TWRP (Nougat 7.1.1)," found in the same EDL thread (to get TWRP).
Note that first I just downloaded the TWRP version, and TWRP successfully installed and I could boot into TWRP, but it would totally freeze before loading the OS ROM every time. You MUST flash the B19 FULL first to avoid this.
STEP 2: INSTALLING MAGISK 13.0 BETA WITH ROOT AND SAFETYNET PASS
1. Make sure you have a clean image with NO SU (PHH or MagiskSU or otherwise), and NO Magisk/Magisk Manager installed.
2. Enable Settings->Security->Unknown Sources in stock.
3. Download Magisk Manager 20170520 13.0 beta and Magisk 20170520 (here, and attached for convenience) (full beta thread here if needed), and copy them to your device.
4. Install Magisk Manager 20170520 13.0 beta via File Manager direct as an APK.
5. Go to TWRP, and install the Magisk 20170520 beta (here, and attached for convenience)
6. Reboot into stock, and open Magisk Manager 13.0. You should see both Magisk and Root installed (Root as "Magisksu"). If you try SafetyNet right now, it will fail.
7. Go into Settings in Magisk Manager and enable MagiskHide.
8. Now if you check SafetyNet, it should pass.
Note that the temporary beta builds appear to only be available for a short time, so either use the files attached, or go ahead and try the latest beta build. The first build I tried, 20170520, worked. Again, my guess is all beta builds or full builds after 20170520 will work with the instructions above, but feel free to test.
STEP 3: GET OTAS: I have not tested yet to ensure Magisk doesn't break, but I believe you should be able to download OTA packages, such as those by DrakenFX and flash them. However, users are reporting some bugs upgrading beyond B19, so OTAs are a work in progress. Please make a TWRP backup before attempting this and be ready to roll back if needed.
6bolt2g reports he had success moving from B19 (rooted) to B25, with the following steps: (a) flash "the DrakenFX B25 flashable zip's and the no-verity zip to keep TWRP"; and (b) follow STEP 2 above. However, 6bolt2g and StickMonster report that after upgrading to B25, you may experience problems with adding apps not previously whitelisted. Again, this is not verified by me but reporting it in the first thread for convenience.
For now, applying OTAs beyond B19 should be considered experimental - please be aware of the risk and have a backup before trying, and share your results here.
Edit 5/21/2017: Added additional steps to Magisk to show process after flashing in TWRP.
Edit 5/23/2017: Added 6bolt2g report re: moving from B19 to B25.
Edit 5/24/2017: Added additional updates re: OTAs.
Click to expand...
Click to collapse
I kept having error Object ref not set to an instance of an object. I already have TWRP, i wonder if i need stock recovery for this to work?
Question: On B25, once you have your root apps whitelisted and root access granted, does the Magisk Manager work alright? Other than FC on new apps, does it still do its thing and the phone work normal? My Axon 7 should be arriving today and I want to be on B25 for the wifi-calling fixes. I can probably live with white listing the apps on B19 and then updating to B25 once everything is ironed out.
genbu said:
I kept having error Object ref not set to an instance of an object. I already have TWRP, i wonder if i need stock recovery for this to work?
Click to expand...
Click to collapse
Can you give more details... whats your starting point? and what step are you getting this error?
---------- Post added at 08:35 AM ---------- Previous post was at 08:33 AM ----------
HallOfPromise said:
Question: On B25, once you have your root apps whitelisted and root access granted, does the Magisk Manager work alright? Other than FC on new apps, does it still do its thing and the phone work normal? My Axon 7 should be arriving today and I want to be on B25 for the wifi-calling fixes. I can probably live with white listing the apps on B19 and then updating to B25 once everything is ironed out.
Click to expand...
Click to collapse
I cant answer for stock AXON 7 OS... but im running LineageOs and everyththing is working very well... no Force closes with apps or anything like that.
installing atm...
flash-all (minus -w) worked fine on my Wife's P3. Magisk 19.3 is working fine, and twrp-3.3.0-0-blueline installs (using ramdisk install method) and dycripts fine as long as you haven't done a full wipe since a couple of Google builds ago when a new install wouldn't decrypt.
public WiFi sign in issue not solved yet.
sliding_billy said:
flash-all (minus -w) worked fine on my Wife's P3. Magisk 19.3 is working fine, and twrp-3.3.0-0-blueline installs (using ramdisk install method) and dycripts fine as long as you haven't done a full wipe since a couple of Google builds ago when a new install wouldn't decrypt.
Click to expand...
Click to collapse
What is "using ramdisk install method" ?
fahmi182 said:
What is "using ramdisk install method" ?
Click to expand...
Click to collapse
That is the permanent TWRP install method that was mentioned a couple of months ago when TWRP said that they would no longer be doing the .zip installers soon. From the main screen in TWRP (after launching the fastboot boot .img), got to advanced and you will see a ramdisk install link. Use that to install the .img (make sure to put the .img on your phone before running it from fastboot) of TWRP permanently.
sliding_billy said:
That is the permanent TWRP install method that was mentioned a couple of months ago when TWRP said that they would no longer be doing the .zip installers soon. From the main screen in TWRP (after launching the fastboot boot .img), got to advanced and you will see a ramdisk install link. Use that to install the .img (make sure to put the .img on your phone before running it from fastboot) of TWRP permanently.
Click to expand...
Click to collapse
Have link for that?
fahmi182 said:
Have link for that?
Click to expand...
Click to collapse
It has been discussed on the P3 and P3XL TWRP forums, but here is the original article.
https://www.xda-developers.com/twrp-3-3-0-release/
No problem installing the July update and Magisk using my ol' pre-patch the boot image method. I've forgotten how to get the device certified in the Play Store now that you can't clear data for it anymore (it shows 0 storage used). I already have it hidden in Magisk. Does it just take some time to refresh the certified status?
CSX321 said:
No problem installing the July update and Magisk using my ol' pre-patch the boot image method. I've forgotten how to get the device certified in the Play Store now that you can't clear data for it anymore (it shows 0 storage used). I already have it hidden in Magisk. Does it just take some time to refresh the certified status?
Click to expand...
Click to collapse
The issue of not being able to clear Play Store cache and data (gray buttons) is likely caused by a Magisk module. It is for me on the 3XL, and in my case it is Edge Sense. Try disabling your modules and reboot. You should be able to clear data and re-enable your modules.
sliding_billy said:
The issue of not being able to clear Play Store cache and data (gray buttons) is likely caused by a Magisk module. It is for me on the 3XL, and in my case it is Edge Sense. Try disabling your modules and reboot. You should be able to clear data and re-enable your modules.
Click to expand...
Click to collapse
Ah, I'm using Edge Sense, too. Although since my earlier post I manually cleared the Play Store data with the package manager (pm clear com.android.vending). Now I guess I just have to wait for it to refresh the certified status (and my list of installed apps).
CSX321 said:
Ah, I'm using Edge Sense, too. Although since my earlier post I manually cleared the Play Store data with the package manager (pm clear com.android.vending). Now I guess I just have to wait for it to refresh the certified status (and my list of installed apps).
Click to expand...
Click to collapse
You can get the installed app list back (as well as any updates that aren't showing) by installing something from your library or just some random app. Delete if necessary of course. The certified status is just a matter of waiting. It'll show up randomly in a day or two most likely.
sliding_billy said:
That is the permanent TWRP install method that was mentioned a couple of months ago when TWRP said that they would no longer be doing the .zip installers soon. From the main screen in TWRP (after launching the fastboot boot .img), got to advanced and you will see a ramdisk install link. Use that to install the .img (make sure to put the .img on your phone before running it from fastboot) of TWRP permanently.
Click to expand...
Click to collapse
So use ramdisk method after. We can don't use fastboot direct into recovery?
Edemilorhea said:
So use ramdisk method after. We can don't use fastboot direct into recovery?
Click to expand...
Click to collapse
You still need to use the fastboot boot .img to even get into TWRP do the install with ramdisk. You do not need to permanently install TWRP though. You can still use fastboot to get into TWRP but leave stock recovery permanently installed. Many do that so they can sideload OTAs.
sliding_billy said:
You still need to use the fastboot boot .img to even get into TWRP do the install with ramdisk. You do not need to permanently install TWRP though. You can still use fastboot to get into TWRP but leave stock recovery permanently installed. Many do that so they can sideload OTAs.
Click to expand...
Click to collapse
If i install ramsisk, i can use magisk?
Twrp and magisk can in the phone at the same time?
Edemilorhea said:
If i install ramsisk, i can use magisk?
Twrp and magisk can in the phone at the same time?
Click to expand...
Click to collapse
Yes, the ramdisk is not something you are installing. It is simply the method that TWRP is using to install itself permanently. Of course, you can then use the permanent version of TWRP (or the fastboot .img version) to flash Magisk.
sliding_billy said:
Yes, the ramdisk is not something you are installing. It is simply the method that TWRP is using to install itself permanently. Of course, you can then use the permanent version of TWRP (or the fastboot .img version) to flash Magisk.
Click to expand...
Click to collapse
Sounds I still not use permanently Twrp, just use fastboot to into recovery enough.
I want to ask a few problems.
I use twrp flash root and magisk better than use patch boot.img?
If I root my phone and i will ota update in future. Just use magisk manager to uninstall magisk and restore factory boot.img?
And now google pay work on new one magisk?
Edemilorhea said:
Sounds I still not use permanently Twrp, just use fastboot to into recovery enough.
I want to ask a few problems.
I use twrp flash root and magisk better than use patch boot.img?
If I root my phone and i will ota update in future. Just use magisk manager to uninstall magisk and restore factory boot.img?
And now google pay work on new one magisk?
Click to expand...
Click to collapse
Using TWRP to root is much easier than patching boot.
If you take a monthly build, yes you will lose root. You don't need to uninstall anything though. Just run the TWRP .img and flash Magisk again. There are Magisk settings like app hides and such that are retained during the update since the are in user and not system. Uninstalling will cause you to have to redo that stuff.
Magisk does not in and of itself give you the ability to use Google Pay. There are a couple of threads on the Magisk page with a lot of information. I use the exact method spelled out in the OP of the thread that starts with [working] on both a Pixel 3 and Pixel 3 XL. There is always a game of cat and mouse with Google and certain methods, but this has been working for me for a few months.
https://forum.xda-developers.com/apps/magisk/magisk-google-pay-gms-17-1-22-pie-t3929950
https://forum.xda-developers.com/apps/magisk/discussion-google-pay-magisk-discussion-t3906703
sliding_billy said:
Using TWRP to root is much easier than patching boot.
If you take a monthly build, yes you will lose root. You don't need to uninstall anything though. Just run the TWRP .img and flash Magisk again. There are Magisk settings like app hides and such that are retained during the update since the are in user and not system. Uninstalling will cause you to have to redo that stuff.
Magisk does not in and of itself give you the ability to use Google Pay. There are a couple of threads on the Magisk page with a lot of information. I use the exact method spelled out in the OP of the thread that starts with [working] on both a Pixel 3 and Pixel 3 XL. There is always a game of cat and mouse with Google and certain methods, but this has been working for me for a few months.
https://forum.xda-developers.com/apps/magisk/magisk-google-pay-gms-17-1-22-pie-t3929950
https://forum.xda-developers.com/apps/magisk/discussion-google-pay-magisk-discussion-t3906703
Click to expand...
Click to collapse
OK And Want to know root and magisk is wrok on Q-BETA Too?
Edemilorhea said:
OK And Want to know root and magisk is wrok on Q-BETA Too?
Click to expand...
Click to collapse
Magisk is working with Q but TWRP is not yet, so you'd have to root with manually patched image. There are posts on the P3 and P3XL pages about how to manually patch to root. There does not seem to be an official solution for Google Pay yet. I don't see anything in Q that makes it worth me not waiting for all of the solutions to be created. They are on 4 of 6 test builds (public will likely coincide with Pixel 4 in the fall), so there is time.
sliding_billy said:
Magisk is working with Q but TWRP is not yet, so you'd have to root with manually patched image. There are posts on the P3 and P3XL pages about how to manually patch to root. There does not seem to be an official solution for Google Pay yet. I don't see anything in Q that makes it worth me not waiting for all of the solutions to be created. They are on 4 of 6 test builds (public will likely coincide with Pixel 4 in the fall), so there is time.
Click to expand...
Click to collapse
Really thanks your answer.
I think I still use PIE, and I will go to root my pixel 3 now, and to study how to Gpay work on Magisk 1.93 now
I saw a lot of person said to use SQL-Edit have to Gpay work on Rooted.
Ah, So You've rooted your 6.1 Plus/X6 but don't know how to Install stock or having troubles with it? I'm here to help!
*All of the instructions and procedures below requires an unlocked bootloader. If you do not have an unlocked bootloader, Please refrain from asking about it here.
*Not having an unlocked bootloader and following this will definitely brick your phone. You have been warned.
Installing Stock ROM - Method 1A(Nost) --
1. Get NOST from here - NOST
2. NOST ONLY SUPPORT OREO FIRMWARE, USE OST LA FOR PIE(Not sharing cause its a patched app, Search on Google and get it from TechMesto)
3. Download unpacked oreo firmware, You can get it from - Here
4. Extract the zip on your PC
5. Put your phone in bootloader mode, Power off - Press Volume Down+Power Button.
6. Now connect it to your PC
7. Open NOST, Select the .mlf file from the folder where you extracted the Firmware
8. Now select, Normal download and Erase User data option.
9. Now click on next and wait for NOST to flash the phone. (It takes 258 seconds or 2.3 - 2.5 minutes on my laptop)
Installing Stock ROM - Method 1B(OST LA) --
Same as NOST, It has the same UI.
Except You might have to change some values in the .mlf file.
An appropriate guide for the same - Here
Installing Stock ROM - Method 2(Hikary's Generic Flashing Script) --
I recommend this method more than NOST and OST LA.
1. Get Hikary's script from - Here
2. Get unpacked Firmware from - Here
3. Extract the Firmware
4. Put the .exe file you got from Github into the folder where you Extracted the firmware
5. Run the script
6. Follow instructions on screen
7. Profit!
Thanks alot to member - Hikary for this easy to use scipt!
You've installed Stock, Now let's add some magisk to it !
*Please disable Automatic System Updates through developer options to make taking OTA .zips easier.
Installing Magisk - Method 1A(Fastboot method) -
You will need Google's ADB drivers, Which you can get - Here/
1. Extract ADB to a Folder
2. Get Magisk patched boot images from - Here Don't worry, Boot images for Nokia 7 Plus will work on DRG(6.1 Plus/X6) and PL2(6.1)
3. Open adb(Type cmd in the address bar of the folder where you extracted adb)
4. Put your device on Download mode
5. type the command
Code:
fastboot boot 'nameofbootimage'.img
6. Now your phone will boot
7. Install Latest Magisk Manger from - [https://www.github.com/topjohnwu/magisk/releases]Here[/url]
8. Open Magisk Manger, You will see Magisk is installed, But there will also be an Install Button next to it. Tap on Install.
9. Let Magisk Install and re-boot the phone
10. Viola Magisk is now permenantly available
Installing Magisk - Method 1B(TWRP method) -
You will need Google's ADB drivers, Which you can get - Here/
1. Get the latest TWRP for 6.1 Plus
2. Get the Latest Magisk Installer from - [https://www.github.com/topjohnwu/magisk/releases]Here[/url]
3. Put the .zip file to your Internal Storage/SD Card
4. Open adb and pass the command
Code:
fastboot boot "nameofrecoveryfile.img"
5. Now TWRP will open on your phone
6. Install Magisk through TWRP
7. Wipe Dalvik
8. Reboot
9. Profit
Now you've got magisk. Follow the next post to see how to take an OTA update with Magisk Installed.
Nokia 6.1 Plus is an Android One certified device. Nokia is no slouch either when it comes to issuing updates. Learn how to take OTA without losing root.
1. Turn of Auto System updates through Developer options
2. Open Magisk Manager
3. Restore Stock Images but don't reboot.
4. Download and install, Let both the steps finish i.e applying update and apps, but don't reboot.
5. Go to magisk manager and select install to inactive slot option
6. Re-boot device.
7. You've not lost root, But have root access.
Done
CarbonGTR said:
Nokia 6.1 Plus is an Android One certified device. Nokia is no slouch either when it comes to issuing updates. Learn how to take OTA without losing root.
1. Turn of Auto System updates through Developer options
2. Open Magisk Manager
3. Restore Stock Images but don't reboot.
4. Download and install, Let both the steps finish i.e applying update and apps, but don't reboot.
5. Go to magisk manager and select install to inactive slot option
6. Re-boot device.
7. You've not lost root, But have root access.
Done
Click to expand...
Click to collapse
I don't see any option to restore stock images or install to inactive slot in Magisk. Am I missing something?
Hymix said:
I don't see any option to restore stock images or install to inactive slot in Magisk. Am I missing something?
Click to expand...
Click to collapse
Open Magisk Manager, Tap on Uninstall. You will see 2 options, Complete Uninstall and restore stock images.
*Nevar tap on the complete uninstall option, It will throw your phone into bootloop
To install to inactive slot, Tap on install, You will get 2 options, Release Notes and Install. Tap on Install again and select install to inactive slot, Reboot from within Magisk Manager.
The simplest way I've found to install Stock Rom is just using adb sideload.
Boot into TWRP and wipe as you would with any custom rom.
Go to advanced and adb sideload.
Send the adb sideload command from your computer with the relevant zip file.
Doesn't require any additional softward like NOST or OST....
Hymix said:
The simplest way I've found to install Stock Rom is just using adb sideload.
Boot into TWRP and wipe as you would with any custom rom.
Go to advanced and adb sideload.
Send the adb sideload command from your computer with the relevant zip file.
Doesn't require any additional softward like NOST or OST....
Click to expand...
Click to collapse
But does it also install the bootloader and stock recovery back? If yes then I'll add it to the post above.
CarbonGTR said:
But does it also install the bootloader and stock recovery back? If yes then I'll add it to the post above.
Click to expand...
Click to collapse
That's a good question. I've just been using stock and hadn't considered it. How would one check that?
Sent from my Nokia 6.1 Plus using Tapatalk
Bluebriz said:
That's a good question. I've just been using stock and hadn't considered it. How would one check that?
Sent from my Nokia 6.1 Plus using Tapatalk
Click to expand...
Click to collapse
It's easy. Get an OTA .zip file, Re-Boot to recovery and flash it. Or Use the ADB Sideload method.
Most likely installing the OTA would fail if the device is rooted because, Magisk will patch the boot.img.
Then I'll need to wait for another update, the September one, right? Because I installed it with ADB and have Magisk installed so I don't really want to mess with it until I have to.
Sent from my Nokia 6.1 Plus using Tapatalk
Bluebriz said:
Then I'll need to wait for another update, the September one, right? Because I installed it with ADB and have Magisk installed so I don't really want to mess with it until I have to.
Click to expand...
Click to collapse
I just took an OTA with Magisk installed it went fine. (September patch)
OK, then it doesn't seem to work. Trying to follow the steps, the system update gives an installation error. I'm guessing that somewhere along the road I've messed something up, so it seems stock rom and Magisk isn't an option for me.
Hymix said:
OK, then it doesn't seem to work. Trying to follow the steps, the system update gives an installation error. I'm guessing that somewhere along the road I've messed something up, so it seems stock rom and Magisk isn't an option for me.
Click to expand...
Click to collapse
Restore images before you do anything, If installation fails keep trying again. It happens to me to.
CarbonGTR said:
Restore images before you do anything, If installation fails keep trying again. It happens to me to.
Click to expand...
Click to collapse
Really? I did the restore via Magisk and that seemed fine, but then the update part didn't work. It downloaded then gave the error so I quit and started again with a fresh installation, minus Magisk.
Sent from my Nokia 6.1 Plus using Tapatalk
Have you guys modified the system/vendor partition in any way? If you did, Then it will obviously fail.
@Bluebriz and @Hymix I agree. It's the september security patch causing the installation issue.
It fails for me no matter what, Unless I completely un-root. But this method works perfectly fine on the August update.
Lets see for the October patch.
Okay, I can specifically narrow this down to way the September patch. The september patch requires the August security patch as a precondition to install. And that's where something funky is happening.
Guys a quick update. October update has been released but it also fails to install. This time I've managed to find the cause, Apparently some service that needs to be used for the update is being blocked/used by Magisk. (I could be wrong here)
The error code according to the recovery is 20(kDownloadStateInitializationError)
Is there any update to this issue?
Tried removing Magisk, didn't help.
Yesterday I got November security update ..iam using magisk...so it is showing installation problem...I tried in recovery and ADB method both didn't work.. finally I ended in bootloop ...so I again installed stock ROM...any solution is there without resetting each time how to install security updates..coz each time my data balance was wasted??
Update 12/15/21: Magisk 23016 incorporates fixes for vbmeta header patching; disabling verity/verification is no longer necessary. Update and root should work as it always has - simply patch and flash the boot image.
Any update method can be used. If you've already disabled verity/verification, simply don't worry about it at next update; no need to re-enable.
I am closing this thread.
Spoiler: Deprecated
On Android 12, boot verification must be disabled in order to run a patched boot image. Unfortunately, if you have never disabled it before, it will require you to wipe data. To be clear:
***************************************************
PERMANENT ROOT CURRENTLY REQUIRES A DATA WIPE.
***************************************************
However, if you don't want to lose your data, you can "live boot" the patched image as long as /vbmeta and /boot are stock. This will allow you to use temporary root. DO NOT attempt to Direct Install Magisk to the boot image.
For subsequent updates, it is imperative that you do not allow the device to boot into system before you have disabled Verified Boot.
What this means: If you sideload the OTA, IMMEDIATELY reboot to bootloader and reflash /vbmeta with --disable-verity and --disable-verification. If you dirty flash the factory image, make sure you add these two switches to the command.
If you fail to do this, and allow the device to boot into system, you WILL have to wipe data to disable it again.
IF YOU ARE ROOTED, DO NOT USE AUTOMATIC UPDATES AS THIS WILL REFLASH /VBMETA WITHOUT DISABLING BOOT VERIFICATION!
Factory Images
OTA Images
Latest Magisk Canary
Spoiler: To root:
On your device, enable Developer Options (tap build number 8 times), and enable the OEM Unlocking toggle. Reboot to bootloader:
Code:
adb reboot bootloader
Unlock bootloader:
Code:
fastboot flashing unlock
Download the latest factory image and extract it. Inside, you will find the bootloader image, the radio image, and the image-device-buildnumber.zip. Extract boot.img and vbmeta.img from this zip.
Flash vbmeta:
Code:
fastboot flash vbmeta --disable-verity --disable-verification <drag and drop vbmeta.img>
Allow the device to boot into Android. Once you have Magisk installed, copy the boot.img and patch it in Magisk, then copy it back to your PC.
Reboot to bootloader.
Flash patched boot image:
Code:
fastboot flash boot <drag and drop magisk_patched-23xxx_xxxxx.img>
Reboot into system.
Spoiler: For subsequent updates:
Download the latest factory image and extract it. Inside, you will find the bootloader image, the radio image, and the image-device-buildnumber.zip. Extract boot.img from this zip.
Reboot to bootloader.
Update bootloader and radio if they are out of date. BE CAREFUL, A MISTAKE CAN BRICK YOUR DEVICE! If you update the bootloader, remember to reboot back to bootloader so that the update reads the correct bootloader version.
Update system:
Code:
fastboot update --disable-verity --disable-verification <drag and drop image-device-buildnumber.zip here>
Note: If you get an error for bootloader/radio version, this means you need to update bootloader and/or radio; go back to step 3.
Allow the device to boot into Android. Copy the boot.img and patch it in Magisk, then copy it back to your PC.
Reboot to bootloader.
Flash patched boot image:
Code:
fastboot flash boot <drag and drop magisk_patched-23xxx_xxxxx.img>
Reboot into system.
I personally do not recommend updating via OTA Sideload, as you would have to download and extract the factory zip anyway. AUTOMATIC OTA WILL LOSE ROOT AND REQUIRE A WIPE TO ROOT AGAIN.
Spoiler: If you choose to update via OTA Sideload:
Sideload the OTA. When complete, IMMEDIATELY reboot to bootloader.
Reflash vbmeta:
Code:
fastboot flash vbmeta --disable-verity --disable-verification <vbmeta.img>
Boot to system and allow the update to complete.
Patch and flash the boot image.
Note: If you run into a bootloader message
failed to load/verify boot images
this means you forgot to disable verity and verification. Reflash vbmeta with the --disable options.
If you run into this recovery message
View attachment 5455805
This means that verity and verification were not disabled before, and a wipe is required to proceed.
Let the fun begin!
Awesome news! Now that the devices are in peoples hands and this is released, development can begin!
So it looks like if you grabbed the Pixel 6 OTA yesterday, you are on 036, and that binary is not yet posted. Please correct if I am wrong. Cant wait to root this thing, non V4A audio is horrible
Just literally got my pixel 6 20 mins ago, I’m at work but when I get home the first thing I’m doing is rooting it!
For some reason I can not unlock the bootloader on the P6.
I unlocked the bootloader in the developer options.
Tried "fastboot flashing unlock" and the CMD says waiting for device.
I can transfer files from the pc to the P6 with no problems.
Maybe I need to check on an ADB driver!
EDIT: Google ADB driver was needed.
Until a Magisk hide alternative is available, what's the point in rooting for those who don't develop? Most banking apps (among others) won't work.
Not to downplay the significance of the importance of this, just asking.
XNine said:
Until a Magisk hide alternative is available, what's the point in rooting for those who don't develop? Most banking apps (among others) won't work.
Not to downplay the significance of the importance of this, just asking.
Click to expand...
Click to collapse
Geez, the firmware was just released today. Give the devs some time, there are other devices they need to update their mods on as well.
vandyman said:
Geez, the firmware was just released today. Give the devs some time, there are other devices they need to update their mods on as well.
Click to expand...
Click to collapse
Again, I was just asking what would be the benefit of rooting for a daily driver for most people (not devs), not trying to be impatient or rude. From my fairly limited understanding, Hide is pretty essential for a plethora of apps to work while rooted.
XNine said:
Again, I was just asking what would be the benefit of rooting for a daily driver for most people (not devs), not trying to be impatient or rude. From my fairly limited understanding, Hide is pretty essential for a plethora of apps to work while rooted.
Click to expand...
Click to collapse
Gotha!
When I had my Pixel 5 rooted I did not need to use hide. I use PNC Bank with no issues. I do not us Gpay, to me it is a waste of time.
I use root for AdAway, Appdash, EX Kernel, and SD Maid.
XNine said:
Until a Magisk hide alternative is available, what's the point in rooting for those who don't develop? Most banking apps (among others) won't work.
Not to downplay the significance of the importance of this, just asking.
Click to expand...
Click to collapse
Use Magisk 23001. You don't have to use 23011. I believe 23000 stable will also work as it still has MagiskHide if I'm not mistaken and works with Riru.
V0latyle said:
Use Magisk 23001. You don't have to use 23011. I believe 23000 stable will also work as it still has MagiskHide if I'm not mistaken and works with Riru.
Click to expand...
Click to collapse
You're a beautiful human being. Thank you!
XNine said:
You're a beautiful human being. Thank you!
Click to expand...
Click to collapse
My wife thinks so too, although "beautiful" isn't the word she uses
Been waiting for kernel source. Skimming through it, there's a ton of exynos named files.
XNine said:
Until a Magisk hide alternative is available, what's the point in rooting for those who don't develop? Most banking apps (among others) won't work.
Not to downplay the significance of the importance of this, just asking.
Click to expand...
Click to collapse
I’ve got an old apk of magisk so I’d assume this would work fine, no?
Also, I’ve got build number showing SD1A.210817.019.C2. Just got my 6 today and didn’t do the OTA security update as batteries to low. Will this work or nope?
DefeatedSouls said:
Also, I’ve got build number showing SD1A.210817.019.C2. Just got my 6 today and didn’t do the OTA security update as batteries to low. Will this work or nope?
Click to expand...
Click to collapse
Patch the image from the factory zip, and boot it instead of flashing it. Then, once booted, use Direct Install in Magisk to patch the boot image already on your phone.
V0latyle said:
Patch the image from the factory zip, and boot it instead of flashing it. Then, once booted, use Direct Install in Magisk to patch the boot image already on your phone.
Click to expand...
Click to collapse
Uh.. normally I’m good at this but okay, I’ll try!
XNine said:
Until a Magisk hide alternative is available, what's the point in rooting for those who don't develop? Most banking apps (among others) won't work.
Not to downplay the significance of the importance of this, just asking.
Click to expand...
Click to collapse
For instance, I need root to use Adguard in local Proxy mode and third-party VPN service. Also, I use CapitalOne, Amex, Discover, Tdbank and Chase with NO MagiskHide. There were problems with Chase, but later they probably realized it's a crap - to block rooted phones to access the app to pay your card. Some of these apps don't let you to login by a fingerprint, but it's not a big deal to enter the password (you won't forget one at least, haha)
Getting Installation failed when trying to patch the boot.img from the factory zip with Magisk.
After updating to april security update everytime that I turn on or restart my pixel 6 I got this message "Your device is corrupt. It can't be trusted and may not work properly" before the unlocked bootloader message, is it normal? Can I fix it?
It would be interesting to know "how" you updated. Just take the "regular" OTA update through system settings? Install to Inactive Slot method? Sideload? Flash-all? And if you were rooted and if so what version of Magisk you were on.
But to get rid of the message there are a few things that you can try that have worked for people and may work for you (dependent on if your bootloader is unlocked of course):
1. Flash the March boot image (it may not boot, that's ok), and then flash the April boot image (seems mostly to work when you get the message as a result of flashing a custom kernel).
2. Flash the April factory image again via flash-all while removing the -w in the flash-all.bat script to keep data.
3. Use Android Flash Tool and install the April update again (uncheck all the boxes)
4. Clean flash the April factory image via flash-all or Android Flash Tool (will lose data)
5. Do nothing and wait until next month's update (some have reported that when doing this the corrupt message went away).
The corrupt message does not appear to affect anything in the negative, so if your phone is working fine you can likely just ignore it and see if it goes away after next month's update.
Lughnasadh said:
It would be interesting to know "how" you updated. Just take the "regular" OTA update through system settings? Install to Inactive Slot method? Sideload? Flash-all? And if you were rooted and if so what version of Magisk you were on.
But to get rid of the message there are a few things that you can try that have worked for people and may work for you (dependent on if your bootloader is unlocked of course):
1. Flash the March boot image (it may not boot, that's ok), and then flash the April boot image (seems mostly to work when you get the message as a result of flashing a custom kernel).
2. Flash the April factory image again via flash-all while removing the -w in the flash-all.bat script to keep data.
3. Use Android Flash Tool and install the April update again (uncheck all the boxes)
4. Clean flash the April factory image via flash-all or Android Flash Tool (will lose data)
5. Do nothing and wait until next month's update (some have reported that when doing this the corrupt message went away).
The corrupt message does not appear to affect anything in the negative, so if your phone is working fine you can likely just ignore it and see if it goes away after next month's update.
Click to expand...
Click to collapse
1- Uninstalled magisk (v24.3) > Restore Images
2- Updated from system (April OTA update)
3- Installed Magisk to Inactive slot and rebooted
So far so good
4- After 2 days, april security update popped up
5- Repeated 1~3 steps and got corrupt error after reboot, I tought I was stuck on bootloop, I tried to use Pixel Flash and Android Flash Tool, but because of the error I couldn't flash anything "automatically", because when the tool reboot to recovery mode it gets stucked at corrupt message and can't access recovery. I wiped all and factory reset, but nothing.
6- I flashed everything through adb and managed to boot, but the message is still tthere.
revhellyoN said:
1- Uninstalled magisk (v24.3) > Restore Images
2- Updated from system (April OTA update)
3- Installed Magisk to Inactive slot and rebooted
So far so good
4- After 2 days, april security update popped up
5- Repeated 1~3 steps and got corrupt error after reboot, I tought I was stuck on bootloop, I tried to use Pixel Flash and Android Flash Tool, but because of the error I couldn't flash anything "automatically", because when the tool reboot to recovery mode it gets stucked at corrupt message and can't access recovery. I wiped all and factory reset, but nothing.
6- I flashed everything through adb and managed to boot, but the message is still tthere.
Click to expand...
Click to collapse
There was a problem updating to the April security update using the install to inactive slot method and Magisk 24.3 (as well as Canary 24305 and earlier) for the Pixel 6 series. It was fixed with Canary 24306.
Some reported that they were able to get rid of the message by dirty flashing the factory image via flash-all.
Lughnasadh said:
There was a problem updating to the April security update using the install to inactive slot method and Magisk 24.3 (as well as Canary 24305 and earlier) for the Pixel 6 series. It was fixed with Canary 24306.
Some reported that they were able to get rid of the message by dirty flashing the factory image via flash-all.
Click to expand...
Click to collapse
I just ran into this same issue. Right after I thought I finally was able to update correctly using the inactive slot method. flash-all with wipe did not correct the issue.
*UPDATE* dirty flash using flash tool did correct the issue AFTER installing Canary 24306. Thank you.
For future Pixel 6 updates, is Magisk Canary 24306 recommended instead of stable 24300?
With the past couple OTA updates I've been using 24300 and when flashing a patched boot image it's been rotating between _a and _b slots and the same for older Canary builds. So far no corruption or boot problems. My only concern is that the last couple OTA updates failed over the internet and I ended up sideloading. I don't know if OTAs failing signals a potential problem or not.
manjaroid said:
For future Pixel 6 updates, is Magisk Canary 24306 recommended instead of stable 24300?
With the past couple OTA updates I've been using 24300 and when flashing a patched boot image it's been rotating between _a and _b slots and the same for older Canary builds. So far no corruption or boot problems. My only concern is that the last couple OTA updates failed over the internet and I ended up sideloading. I don't know if OTAs failing signals a potential problem or not.
Click to expand...
Click to collapse
Well, I guess that depends on how you are updating. As you probably know, the April build brought some grief to those who update via "Install to Inactive Slot". Thus, if using this method, Canary 24306 would likely be the best way to go, although who knows what Google has in store for us in May.
Your OTAs could be failing for a number of reasons. You pretty much want to be stock without having /system, /vendor, etc. modified, as well as not being on a custom kernel.
Lughnasadh said:
Your OTAs could be failing for a number of reasons. You pretty much want to be stock without having /system, /vendor, etc. modified, as well as not being on a custom kernel.
Click to expand...
Click to collapse
So far my updates are 2 for 4: first couple were over the air, last couple had to be sideloaded (got the phone in January). I've been on stock the whole way including the kernel, and haven't messed with the root file system, not on purpose anyway. I won't worry about the OTAs until things get messier, but I might go with Magisk Canary in May out of curiosity.
Is there any guide about how to change to magisk stable for magisk canary? All I find at Google is old, like changing update channel
revhellyoN said:
Is there any guide about how to change to magisk stable for magisk canary? All I find at Google is old, like changing update channel
Click to expand...
Click to collapse
Uninstall the Canary app and install the Stable app and then direct install (or patch and flash your boot image again with the Stable app).
Just finished upgrading to May build and patched with Magisk 24300, disabled flags, everthing is good for now.