HTC touch dual手机,刷了hardSPL 1.16 后反复刷了英文和简体中文版本都正常,今天试着在三色屏下,用 MTTY下执行了 task 2a 后,手机再起不来,也进不了三色屏,用数据线连接到计算机后,有提示找到硬件,但是一直提示查找驱动程序!进不了三色屏,也就刷不了ROM,怎么办呀?
English please! i don't understand this :s
gswangmd said:
HTC touch dual手机,刷了hardSPL 1.16 后反复刷了英文和简体中文版本都正常,今天试着在三色屏下,用 MTTY下执行了 task 2a 后,手机再起不来,也进不了三色屏,用数据线连接到计算机后,有提示找到硬件,但是一直提示查找驱动程序!进不了三色屏,也就刷不了ROM,怎么办呀?
Click to expand...
Click to collapse
HTC touch dual (P5520)
1. try to connect with MTTY via USB and type "task 2a" and "ResetDevice" reboot Nike,but device is dead!
You stay in Bootloader?
If yes ... MTTY type "boot"
If it doesnt work ... flash a full Rom or try via OEMSBL and MTTY "cego"
Arrgh, task 2a formats aARM flash
If your device is security unlocked it can be easily unbricked.
If not you will have to contact me for further steps (preferrably in english)
jockyw2001 said:
Arrgh, task 2a formats aARM flash
If your device is security unlocked it can be easily unbricked.
If not you will have to contact me for further steps (preferrably in english)
Click to expand...
Click to collapse
1. My NIKI maybe security unlocked.
2. Connect to Windows ,but prompy me to install 3 drivers.
My Question: How to flash ROM and make it normal. Please give me detail help message!
gswangmd said:
1. My NIKI maybe security unlocked.
2. Connect to Windows ,but prompy me to install 3 drivers.
My Question: How to flash ROM and make it normal. Please give me detail help message!
Click to expand...
Click to collapse
Check your PM and reply to me
jockyw2001 said:
Check your PM and reply to me
Click to expand...
Click to collapse
What PM?
P5520 OR NIKI 100?
jockyw2001 said:
Check your PM and reply to me
Click to expand...
Click to collapse
With MTTY and task 2a
My pda maybe stucked into OEMSBL: NO Os, No Radio and NO BOOTLOADER to load!
1. with MTTY via USB and type "task 2a" and "ResetDevice" reboot Nike,but device is dead!
2. Now, it doesn't respond to any of the buttons on the phone. Connect to Windows , always prompy me to install 3 drivers.
I think the phone is stucked into OEMSBL: NO Os, No Radio and NO BOOTLOADER to load. How to make it normal?
Now nike fault as follows:
1. Automatic entry into the boot (send + camera) engineering qualcomm mode
2. Do not show
3. Computer display driver to be installed, the installation msm7200 drive ok
4. Mtty open com8 (qualcomm diagnostics interface 6000 com8)
5. Not unlock,
Now only supports the following orders, testing various orders, but not retire this engineering model
Radata
Powerdown
Setboot
GO2AMSS
Rseed
Pmic_vib_off
Pmic_vreg
Pmic_level
Pmic_vib_on
Rpass
I also tested with kaiser(p4550) orders "setboot 1" it is not a show, but set back on the normal "setboot 0"
jockyw2001, come in pls!
try my mind
看得明中文?关机的情况下按住相机键(camera key),然后插上USB,手机就会开机并进三色屏,或者按住相机键,再按电源开关,然后就可以再刷机了,要刷一个full rom。
用mtty有反映,
reboot是不行的提示Invalid command : reboot
cego也不行,提示Invalid command :cego
setboot有反映,提示ARM9BootMode:1
rseed也有反映,提示HTCS6B60C2B012B8E95520B0F4852802B89E*;ÔHTCE
其他就不知道怎么搞了。
手机买来时已经刷了hardspl,是否解锁还不太清楚,根据现在的情况看来,可能没有真正解锁。
看来kaiser买来时还是要自己先解锁再使用,免得出现真砖。
还是期待高手出现,不想寄回原厂,暂时使用830。
cantonese said:
看得明中文?关机的情况下按住相机键(camera key),然后插上USB,手机就会开机并进三色屏,或者按住相机键,再按电源开关,然后就可以再刷机了,要刷一个full rom。
Click to expand...
Click to collapse
试过了,没有用!
Who can help me?
gswangmd said:
Who can help me?
Click to expand...
Click to collapse
No unbricker in the moment!
NetrunnerAT said:
No unbricker in the moment!
Click to expand...
Click to collapse
Who can help me?
I'm a long time lurker but I think that if jockyw2001 can't help you then your device is dead. Maybe the frankenkaiser unbricker tool can help you now - again jockyw2001 will know about that (it's his tool i think) or maybe netrunnerat.
Related
According to the problem of "Invalid Vendor ID" when trying to restore the original rom that i mentioned the topic 'XDA Live report'. I really wanna know to sovle this problem.I did update rom 'RUU_HERMES_HTC_WWE_1[1].35.255.2_1.35.255.102_1.08.00.10_SHIP.EXE' afte that i updated my dopod 838 pro to Rom ' XDA Live' for a few day. I want to use the original rom 'HER_DopodAsia_1237074_1060010_WWE_SHIP.exe' then i updated my hermes to the HER_DopodAsia_1237074_1060010_WWE_SHIP.exe.Then reset my dopod 838 pro. I saw the first screen 'No gsm' and stop everything at the welcome screen. So i tried to fix the problem as the wiki 's suggestion by pressing button 'OK' and Power together with reset by stylus for enter the tri colour for updating but the big problem is that my dopod 838 pro can't connect to computer. The icon 'synconize' at the task bar shown gray colour not green colour !!!!
What should i do now ? Pls Help me !!!
Does your device show USB at the bottom of the tri-colored screen when connected to your PC?
It shown USB at the bottom!!
can your phone boot? not into bootloader mode but into the normal mode
can't boot normally..stop at the welcome screen
I had the same problem when I had the Cingular 2.06 ROM and wanted to put back again SA 1.35 ROM...for the exception I was stacked in Bootloader. I get the "Invalid vendor" error and instead of ran the upgrade again I disconnected my device...and from that moment stacked in bootloader and grey icon in windows...But I managed to unbrick my device by putting on again the ROM I have before I have tried to upgrade...so I had to put on again the Cingular 2.06 ROM and it works for me (or I was just lucky)...but believe me...it was 3 hours of fear & suffer...
Hope you will be able to unbrick your device...
Regards,
Primoz
Is there any rom which can unlock this error? There is a lot of rom at wiki.I don't know the previous rom that i had before ....
...I assume you have the original ROM on your device...or you have made some other ROM updates before?...if you have a Cingular put the latest Cingular ROM...if you have a HTC (original) device put the last HTC ROM...and so on...I hope this could help you...
Regards,
Primoz
Pc78 said:
...I assume you have the original ROM on your device...or you have made some other ROM updates before?...if you have a Cingular put the latest Cingular ROM...if you have a HTC (original) device put the last HTC ROM...and so on...I hope this could help you...
Regards,
Primoz
Click to expand...
Click to collapse
How baout the coneection between my dopod 838 pro and computre? Because it shown gray icon instead green icon ? How to connect ?
jcute said:
How baout the coneection between my dopod 838 pro and computre? Because it shown gray icon instead green icon ? How to connect ?
Click to expand...
Click to collapse
It doesn`t metter...in my case it was grey too...but I managed to upgrade...just try...I think you cannot be in worst situation you are now...give it a tray and report...I hope it work!
Regards,
Primoz
Pc78 said:
It doesn`t metter...in my case it was grey too...but I managed to upgrade...just try...I think you cannot be in worst situation you are now...give it a tray and report...I hope it work!
Regards,
Primoz
Click to expand...
Click to collapse
I did update rom "HER_DopodAsia_1237074_1060010_WWE_SHIP.exe" ( The original rom' but still got the same problem !!!
jcute said:
I did update rom "HER_DopodAsia_1237074_1060010_WWE_SHIP.exe" ( The original rom' but still got the same problem !!!
Click to expand...
Click to collapse
did the install complete successfully?
are you able to mtty into the device?
jeRrRKKKK said:
did the install complete successfully?
are you able to mtty into the device?
Click to expand...
Click to collapse
not complete!!! i did mtty to my device. There is no error.Should i save after finish ?
This is what i did...
Type the following commands (do not copy paste!!!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
After set 1e 0....what should i do next ?
Hmmm password?!...I think you should type info 2...not password...?!
Regards,
Primoz
Pc78 said:
Hmmm password?!...I think you should type info 2...not password...?!
Regards,
Primoz
Click to expand...
Click to collapse
can you give me the complete command ?
jcute said:
can you give me the complete command ?
Click to expand...
Click to collapse
Connect to the PC and run mtty.exe and you get this
USB>
type: task 32
then type: info 2
before running mtty.exe uncheck "Allow USB connection" in the connection settings of Activesync...
When you will try to update don`t forget to check again "Allow USB connection"!
Regards,
Primoz
p.s. I think you should move to the sticky theme of dead hermes...
Pc78 said:
Connect to the PC and run mtty.exe and you get this
USB>
type: task 32
then type: info 2
before running mtty.exe uncheck "Allow USB connection" in the connection settings of Activesync...
When you will try to update don`t forget to check again "Allow USB connection"!
Regards,
Primoz
p.s. I think you should move to the sticky theme of dead hermes...
Click to expand...
Click to collapse
Pls take a look !
jcute said:
Pls take a look !
Click to expand...
Click to collapse
Mhmmm...try firt to put a space in front of commands like this-
USB> task 32
USB> info 2
...
regards,
Primoz
what is your bootloader version?
if you can mtty in, simply load the os again...
lnb OS.nb
then let it boot in first
later then decide, is radio working? is OS working?
Hi i'm newbie
I'm french thus excuse me for my english
I try to upgrade my htc in WM6, i sucess, no problem.
After i upgrade with a rom radio and the upgrade block at 40 %.
Now the phone boot in tricolor mode.
IPL-1.04
SPL-2.10.Olipro
I find in the forum that for unbricked my htc i must to flash any rom in nbh format.
How to do that.
I try to install also original ROM_9600_FRA_10303.exe rom but activsync it not active.
Someone can help me please
thanks
Connect you device in bootloader screen with your PC with USB and you should see USB appear at the bottom of the screen on yor device. Now flash any .nbh with the RUU wrapper and select SPL 2.10 New bootloader and flash the ROM...
what is the RUU Wrapper, where can i download it?
unikgwada said:
what is the RUU Wrapper, where can i download it?
Click to expand...
Click to collapse
Here it is
RUU wrapper is a software?
Explain me which is it
unikgwada said:
RUU wrapper is a software?
Explain me which is it
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=298737
when i use RUUWrapper i havbe an error [260].
What i can do
In the tri color screen with the device plugged in via USB do you have USB written at the bottom? Does your device appear in the device manager?
Yes USB is written on the bottom, and yes the phone appear in device manager .
What are you using XP or vista?? You could try a different USB port or if that doesn´t work you may have to roll back the driver... read this http://forum.xda-developers.com/showthread.php?t=299657
I'm using XP.
When i use myyt.exe the phone make something, but when i try to upgrade any rom i have always this message error [260]
i try to update with rom radio 1.47.00.10 , the upgrade is correct 100%
but when i reboot i return in tricolor mode
I success to install rom with UUwrapper but now the phone block on the picture windows mobile
Thanks
i fine a the solution
Could you please share the solution ? I've got a similar case, thanks.
My Raphael is dead...
1. I flash Hard SPL 1.90.OliNex
2. I flash original Russian ROM and have this message on screen "Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center"
3. I flash stock SPL
and now when I'm trying to flash any ROM or Hard SPL I have on the screen of PC "0% image upgrade in progress" and "0%" on the screen of Raphael
after some time on the screen of PC I see ERROR [262]: UPDATE ERROR
What I must to do?
Help me, please
P.S.
Now when I'm trying to flash HTC_Raphael_hTC_Asia_WWE_1.90.707.1_Radio_Signed_R aphael_52.33.25.17_1.02.25.19 I have "Invalid Vendor ID" Message
dishef said:
P.S.
Now when I'm trying to flash HTC_Raphael_hTC_Asia_WWE_1.90.707.1_Radio_Signed_R aphael_52.33.25.17_1.02.25.19 I have "Invalid Vendor ID" Message
Click to expand...
Click to collapse
When you receive "Invalid Vendor ID", than your device is not Hard SPL! Please follow the update procedure again. There must have been something wrong.
DeepThought said:
When you receive "Invalid Vendor ID", than your device is not Hard SPL! Please follow the update procedure again. There must have been something wrong.
Click to expand...
Click to collapse
But when I'm trying to flash Hard SPL I have ERROR[262]
Does any method to flash Hard SPL from SD card exist?
dishef said:
But when I'm trying to flash Hard SPL I have ERROR[262]
Click to expand...
Click to collapse
Read here please http://forum.xda-developers.com/showthread.php?t=425922
taiseer999 said:
Read here please http://forum.xda-developers.com/showthread.php?t=425922
Click to expand...
Click to collapse
sorry for the offtopic (or not...)
i have tryied many times to connect to my TP using mtty, but no luck. i'm using Vista Ultimate, and can connect and use mtty with my Kaiser, but can't with Raphael.
Is there any special thing i need to do to get mtty working with raphael?
Thanks in advance
Cheers
jcespi2005 said:
sorry for the offtopic (or not...)
i have tryied many times to connect to my TP using mtty, but no luck. i'm using Vista Ultimate, and can connect and use mtty with my Kaiser, but can't with Raphael.
Is there any special thing i need to do to get mtty working with raphael?
Thanks in advance
Cheers
Click to expand...
Click to collapse
Have you remembered to disable USB connections from activesync connection settings?
taiseer999 said:
Read here please http://forum.xda-developers.com/showthread.php?t=425922
Click to expand...
Click to collapse
i used the MTTY to format the device
but still have ERROR[262] when trying to flash Hard SPL
using info 2 on MTTY i got "HTCSHTC__J15Wаа`HTCE"
but I have HTC Raphael (Touch Pro)
does any way to flash hard spl with MTTY exist?
or may be I can flash ROM with MTTY?
i have this problem whit hard spl
i test it whitout sim-micro sd-win xp-win vista-i dont use usb hub
i use ssple but i had 262 error again and pc was hang on 0%
i have touch pro
i dont want MTTY
it's risk
maby my phon is going to be off for ever
This procedure can damage your phone
HI,
Anyone tried revert back to Stock-SPL trough MicroSD?
I did, wel... the SPL is back, but i'm getting this screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
this is in the TRI-COLOR screen and i'm not getting a USB connection (this is the problem why i reverting back to stock SPL, USB is not recognized)
Please help!
Possibly re-flash your ROM? But I'm no expert on this.. so don't trust me fully.
Already tried... nope
Flash hard spl and start over. Try reading the instructions on reverting to stock-there are plenty of resources here. Do the spl over usb, and do it last.
My USB isn't working!
Other updates doesn't work
Follow these steps:
# Download mtty.exe from here: http://taeguk.co.uk/xda
# Disable activesync (connection settings -> uncheck "allow usb connections")
# Kill the following two processesto stop active sync; rapimgr.exe and wcescomm.exe (Ctrl+Shift+Esc, select from the list of processes).
# Connect your Kaiser to PC using USB cable.
# Open mtty, select USB port and click OK.
# Hit ENTER twice, you should see the "Cmd>" prompt.
# type "set 16 0" (without quotes) and press ENTER.
Reboot.
Ta
Dave
DaveShaw said:
Follow these steps:
# Download mtty.exe from here: http://taeguk.co.uk/xda
# Disable activesync (connection settings -> uncheck "allow usb connections")
# Kill the following two processesto stop active sync; rapimgr.exe and wcescomm.exe (Ctrl+Shift+Esc, select from the list of processes).
# Connect your Kaiser to PC using USB cable.
# Open mtty, select USB port and click OK.
# Hit ENTER twice, you should see the "Cmd>" prompt.
# type "set 16 0" (without quotes) and press ENTER.
Reboot.
Ta
Dave
Click to expand...
Click to collapse
this is the problem why i reverting back to stock SPL, USB is not recognized
Click to expand...
Click to collapse
It's staying SERIAL
binky11 said:
It's staying SERIAL
Click to expand...
Click to collapse
I don't think you can remove RUUNBH just from the SD card.
You posted the SPL is 1.90. this is a stock one IIRC.
Dave
DaveShaw said:
I don't think you can remove RUUNBH just from the SD card.
You posted the SPL is 1.90. this is a stock one IIRC.
Dave
Click to expand...
Click to collapse
When i try a ROM, RADIO ROM or SPL it stays on Loading...
It's really frustrating..
binky11 said:
When i try a ROM, RADIO ROM or SPL it stays on Loading...
It's really frustrating..
Click to expand...
Click to collapse
It will, the RUUNBH flag is stopping it.
As I said before, the SPL you posted is 1.90 and doesn't say Olinex, so I'm guessing it's stock. Why can't you return the device?
Dave
I don't think that's warranty?
binky11 said:
I don't think that's warranty?
Click to expand...
Click to collapse
Unless it says Olinex I'm pretty sure it's stock. From what I've heard HTC are on the lookout for the "OliNex" mark in the bootloader, which you don't have.
I cannot see any reason it would be rejected (unless you still have a custom ROM and they somehow get it to boot).
That's just my opinion, but I can't think of any way to get it to boot WM without USB working again.
Dave
DaveShaw said:
Unless it says Olinex I'm pretty sure it's stock. From what I've heard HTC are on the lookout for the "OliNex" mark in the bootloader, which you don't have.
I cannot see any reason it would be rejected (unless you still have a custom ROM and they somehow get it to boot).
That's just my opinion, but I can't think of any way to get it to boot WM without USB working again.
Dave
Click to expand...
Click to collapse
I tried the lastest Vodafone ROM from UK. It's says Not Allow..
So i'm on the lookout for the Dutch version (the one on the wiki doesn't work)
binky11 said:
I tried the lastest Vodafone ROM from UK. It's says Not Allow..
So i'm on the lookout for the Dutch version (the one on the wiki doesn't work)
Click to expand...
Click to collapse
This is what hey says with the Vodafone UK ROM
Loading...
Checking...
00028002
Not Allow
DaveShaw said:
I don't think you can remove RUUNBH just from the SD card.
You posted the SPL is 1.90. this is a stock one IIRC.
Dave
Click to expand...
Click to collapse
RUUNBH can be removed by flashing a valid image that 100% completes the flash. even if it is done via SD
DaveShaw said:
It will, the RUUNBH flag is stopping it.
As I said before, the SPL you posted is 1.90 and doesn't say Olinex, so I'm guessing it's stock. Why can't you return the device?
Dave
Click to expand...
Click to collapse
yeah, I'd like to know that myself.
binky11 said:
I don't think that's warranty?
Click to expand...
Click to collapse
is the ROM on the device stock? I'm asking because they can get it booting if they really want to. the question is of course whether they wish to go to that trouble just to check as the SPL itself is stock so it looks nice
so anyway let me know if it's cooked or not
cmonex said:
is the ROM on the device stock? I'm asking because they can get it booting if they really want to. the question is of course whether they wish to go to that trouble just to check as the SPL itself is stock so it looks nice
so anyway let me know if it's cooked or not
Click to expand...
Click to collapse
Well.. as far as i know it's stock.. i downloaded the Dutch Vodafone ROM from the WIKI.
Hope that helps
stock voda ROM
did it work ?
http://www.vodafone.nl/Vodafone/wg20/software/RUU_Raphael_Vodafone_NL_1.90.172.4_Radio_Signed_Raphael_CRC_52.33.25.17_1.02.25.19_Ship.exe
this is the stock ROM on the voda NL website
phone have spl-1.16(was in phone,i don't make hardspl) but when i try write an cooked rom phone stop at 75% and now start in bootloader with power on+camera buton, with power on buton phone start in white screen and one vibration.
i try something with mtty but i don't understand very goog the procedure,i need a memory card insert in phone or without memory card?
when i start mtty and write first comand:
Cmd>password BsaD5SeoA
Pass.
HTCST ÚÈÒHTCE
Cmd>
i don't know what do now
can help me somebody?
thanks
nobody can help me?
iugo said:
nobody can help me?
Click to expand...
Click to collapse
I can try, can you tell me what is written in your bootlader and stop using mtty.
Regards,
in left screen writte:
NIKI100
SPL-1.16.0000
CPLD-4
and in down screen write SERIAL without cable in phone and when i insert cable in phone write USB
iugo said:
in left screen writte:
NIKI100
SPL-1.16.0000
CPLD-4
and in down screen write SERIAL without cable in phone and when i insert cable in phone write USB
Click to expand...
Click to collapse
Thanks, just download This rom after download just connect you're phone to your computer, make sure your phone is in bootloader and run the exe from the download this will flash the original rom, if everything is ok, you will have the original wm 6.1 rom after that you need to Hardspl your phone, just read this Thread.
Just keep me informed if the original rom can not be flashed.
Succes buddy
dont'n work ,stop at 1% after that phone restart in white screen. i attached file with error.
In which language was your original rom ?
before was in italian language
iugo said:
before was in italian language
Click to expand...
Click to collapse
Here is the link for Italian, try to do the same as I mentioned before, just make sure active sync or wmdc is turned off.
Greetz,
thanks man,with that rom phone work, now can instal hardspl 1.22? is ok that hardspl?
iugo said:
thanks man,with that rom phone work, now can instal hardspl 1.22? is ok that hardspl?
Click to expand...
Click to collapse
Yep buddy, that's ok, now you can do the Hardspl as I mentioned before, just read carefull.
Succes,
now work with new rom cooked, i see in phone gps antena,have integrated gps antena? wi-fi suport?
iugo said:
now work with new rom cooked, i see in phone gps antena,have integrated gps antena? wi-fi suport?
Click to expand...
Click to collapse
Perfect it worked for you, enjoy your cooked rom, and sorry no wifi, the gps is for communication with an external gps receiver.
Greetz,
ok, thanks for your help.