According to the problem of "Invalid Vendor ID" when trying to restore the original rom that i mentioned the topic 'XDA Live report'. I really wanna know to sovle this problem.I did update rom 'RUU_HERMES_HTC_WWE_1[1].35.255.2_1.35.255.102_1.08.00.10_SHIP.EXE' afte that i updated my dopod 838 pro to Rom ' XDA Live' for a few day. I want to use the original rom 'HER_DopodAsia_1237074_1060010_WWE_SHIP.exe' then i updated my hermes to the HER_DopodAsia_1237074_1060010_WWE_SHIP.exe.Then reset my dopod 838 pro. I saw the first screen 'No gsm' and stop everything at the welcome screen. So i tried to fix the problem as the wiki 's suggestion by pressing button 'OK' and Power together with reset by stylus for enter the tri colour for updating but the big problem is that my dopod 838 pro can't connect to computer. The icon 'synconize' at the task bar shown gray colour not green colour !!!!
What should i do now ? Pls Help me !!!
Does your device show USB at the bottom of the tri-colored screen when connected to your PC?
It shown USB at the bottom!!
can your phone boot? not into bootloader mode but into the normal mode
can't boot normally..stop at the welcome screen
I had the same problem when I had the Cingular 2.06 ROM and wanted to put back again SA 1.35 ROM...for the exception I was stacked in Bootloader. I get the "Invalid vendor" error and instead of ran the upgrade again I disconnected my device...and from that moment stacked in bootloader and grey icon in windows...But I managed to unbrick my device by putting on again the ROM I have before I have tried to upgrade...so I had to put on again the Cingular 2.06 ROM and it works for me (or I was just lucky)...but believe me...it was 3 hours of fear & suffer...
Hope you will be able to unbrick your device...
Regards,
Primoz
Is there any rom which can unlock this error? There is a lot of rom at wiki.I don't know the previous rom that i had before ....
...I assume you have the original ROM on your device...or you have made some other ROM updates before?...if you have a Cingular put the latest Cingular ROM...if you have a HTC (original) device put the last HTC ROM...and so on...I hope this could help you...
Regards,
Primoz
Pc78 said:
...I assume you have the original ROM on your device...or you have made some other ROM updates before?...if you have a Cingular put the latest Cingular ROM...if you have a HTC (original) device put the last HTC ROM...and so on...I hope this could help you...
Regards,
Primoz
Click to expand...
Click to collapse
How baout the coneection between my dopod 838 pro and computre? Because it shown gray icon instead green icon ? How to connect ?
jcute said:
How baout the coneection between my dopod 838 pro and computre? Because it shown gray icon instead green icon ? How to connect ?
Click to expand...
Click to collapse
It doesn`t metter...in my case it was grey too...but I managed to upgrade...just try...I think you cannot be in worst situation you are now...give it a tray and report...I hope it work!
Regards,
Primoz
Pc78 said:
It doesn`t metter...in my case it was grey too...but I managed to upgrade...just try...I think you cannot be in worst situation you are now...give it a tray and report...I hope it work!
Regards,
Primoz
Click to expand...
Click to collapse
I did update rom "HER_DopodAsia_1237074_1060010_WWE_SHIP.exe" ( The original rom' but still got the same problem !!!
jcute said:
I did update rom "HER_DopodAsia_1237074_1060010_WWE_SHIP.exe" ( The original rom' but still got the same problem !!!
Click to expand...
Click to collapse
did the install complete successfully?
are you able to mtty into the device?
jeRrRKKKK said:
did the install complete successfully?
are you able to mtty into the device?
Click to expand...
Click to collapse
not complete!!! i did mtty to my device. There is no error.Should i save after finish ?
This is what i did...
Type the following commands (do not copy paste!!!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
After set 1e 0....what should i do next ?
Hmmm password?!...I think you should type info 2...not password...?!
Regards,
Primoz
Pc78 said:
Hmmm password?!...I think you should type info 2...not password...?!
Regards,
Primoz
Click to expand...
Click to collapse
can you give me the complete command ?
jcute said:
can you give me the complete command ?
Click to expand...
Click to collapse
Connect to the PC and run mtty.exe and you get this
USB>
type: task 32
then type: info 2
before running mtty.exe uncheck "Allow USB connection" in the connection settings of Activesync...
When you will try to update don`t forget to check again "Allow USB connection"!
Regards,
Primoz
p.s. I think you should move to the sticky theme of dead hermes...
Pc78 said:
Connect to the PC and run mtty.exe and you get this
USB>
type: task 32
then type: info 2
before running mtty.exe uncheck "Allow USB connection" in the connection settings of Activesync...
When you will try to update don`t forget to check again "Allow USB connection"!
Regards,
Primoz
p.s. I think you should move to the sticky theme of dead hermes...
Click to expand...
Click to collapse
Pls take a look !
jcute said:
Pls take a look !
Click to expand...
Click to collapse
Mhmmm...try firt to put a space in front of commands like this-
USB> task 32
USB> info 2
...
regards,
Primoz
what is your bootloader version?
if you can mtty in, simply load the os again...
lnb OS.nb
then let it boot in first
later then decide, is radio working? is OS working?
Related
hi everybody,
i am very sad today because i tried to unlock my SFR v1605 (french version of hermes) in order to put an orange sim card.
Everything was ok during the flash but at the end of the procedure i get an error message.
Since them, i can't flash it again, everytime i have an error message.
I have tried a lot of roms but anyone worked.
what can i do now
please help me,
Sorry for my bad english, i tried to do my best to be understood
Thanks
Read "Problem 5: Device shows NO GSM when booting" on the Common Upgrading Problems in HTC Hermes wiki page. Solution is there for you
i've read it but i don't know what rom i have to choose.
i am trying to flash with RUU172541FRA_SFR rom
but the screen of my pda is whit and i wait, i wait.0.. nothing's happen
The Himaupgrade software said
'the current software is now being erased, etc...)
..
totaly update should take 30 mn.
It is normal that when i want to flash actyvsync is not lauched automaticly?
please tell me what to do
on a french forum other guys have the same probleme and i want to help them, and help myself of course.
But now anyone have found the exact procedure to bring the pda alive
I put the instructions on the WIKI: Hermes_UpgradeProblems
A lot of people is having the same problem (you'll see NO GSM when booting), yesterday we found how to fix it:
1. Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2. Put your Hermes in bootloader mode
3. Connect device to computer using USB cable.
4. Open mtty.exe and select USB port, then connect.
5. Hit enter twice, you will see the "USB>" prompt.
6. Type the following commands (do not copy paste!!!)
Code:
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
7. Reset your phone and put it back in bootloader mode
8. Flash the extracted radio ROM of your choice
Click to expand...
Click to collapse
Tanks you very much pof for you help
i am trying it
i will give you news as soon as i have results
my config
SFR v1605 - Herm200 - rom 1.23.163.3
what rom i have to choose?
my keybord is azerty?
ptiga100gene said:
my config
SFR v1605 - Herm200 - rom 1.23.163.3
what rom i have to choose?
my keybord is azerty?
Click to expand...
Click to collapse
you have to choose a radio rom only, it doesn't matter which one.
I have this message
checking information from your device
and it's very long....
that's is normal?
ptiga100gene said:
I have this message
checking information from your device
and it's very long....
that's is normal?
Click to expand...
Click to collapse
please read the wiki and the posts linked there it's all explained, i have no time now sorry
thanks for the time you spent for me
i respect all the procedure, but nothing.
i will try gain and again
if someone can help me
my msn
[email protected]
i have not find a solution
Does a rom exist for my french herm200 (sfr v1605) 1.04 azerty?
please help me
I have Xda Trion Herm100 and in Hermes_Upgrade Problems i saw my problem solution:
Problem 5: Device shows NO GSM when booting
* The radio stack is screwed, you don't get GSM signal and the phone says unknown SIM status
* Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1)
Here is how to fix it:
1. Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2. Put your Hermes in bootloader mode
3. Connect device to computer using USB cable.
4. Open mtty.exe and select USB port, then connect.
5. Hit enter twice, you will see the "USB>" prompt.
6.
Type the following commands (do not copy paste!!!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
7. Reset your phone and put it back in bootloader mode
8. If your bootloader version is different than 1.04 then Flash Bootloader version 1.04
9. Flash the patched radio used to simunlock the Hermes
10. Your phone should be alive again
Click to expand...
Click to collapse
and i was so happy, but on step 6 i can`t understand when i`m writing the first row " USB> password 0000000000000000" and hit Enter it is show "HTCSPass1.CM€ЛHTCEUSB>"
and i`m thinking is on that row i must write " USB> set 1e 1" or i must hit Enter to show me new "USB>" and then write " USB> set 1e 1" ( Here is the log
USB>password 0000000000000000
HTCSPass1.CM€ЛHTCEUSB>
USB>set 1e 1
USB>erase a0040000 c80000
HTCST ЪИТHTCEUSB>
USB>erase a0cc0000 c80000
HTCST ЪИТHTCEUSB>
USB>erase a1940000 640000
HTCST ЪИТHTCEUSB>
USB>set 1e 0 )
and finnaly when i write "USB> set 1e 0" must hit any of the buttons or only close the programm ( is there any button to save these rows on the Xda device or it is automatic )
then in bootloader mode there are 2 text ..
One in white colour
"Herm100
IPL-1.01"
and one in yellow colour
"Herm100
SPL-1.06"
which of them is my bootloader version, and if 1.06 is my bootloader please tell me how to flash with bootloader 1.04 and at last
"9. Flash the patched radio used to simunlock the Hermes"
where is this Patched Radio ...
thank you in advice
WorldMaster said:
when i`m writing the first row " USB> password 0000000000000000" and hit Enter it is show " "
Click to expand...
Click to collapse
It should show you "Pass1" encapsulated in HTCS-HTCE block. Otherwise somthing is not going ok. You don't have to type "USB>" this is the prompt from bootloader.
WorldMaster said:
and i`m thinking is on that row i must write " USB> set 1e 1" or i must hit Enter to show me new "USB>" and then write " USB> set 1e 1"
Click to expand...
Click to collapse
It doesn't matter, you can write it on this row or hit Enter and write it on a new row.
WorldMaster said:
and finnaly when i write "USB> set 1e 0" must hit any of the buttons or only close the programm ( is there any button to save these rows on the Xda device or it is automatic )
Click to expand...
Click to collapse
You can safely close mtty when finished, each command is executed on the device after you hit enter, no need to save or anything.
WorldMaster said:
then in bootloader mode there are 2 text ..
One in white colour
"Herm100
IPL-1.01"
and one in yellow colour
"Herm100
SPL-1.06"
which of them is my bootloader version
Click to expand...
Click to collapse
You have bootloader 1.06.
WorldMaster said:
and if 1.06 is my bootloader please tell me how to flash with bootloader 1.04
Click to expand...
Click to collapse
In short, you can't... but please read the wiki, and search this forum before asking.
WorldMaster said:
and at last
"9. Flash the patched radio used to simunlock the Hermes"
where is this Patched Radio ...
Click to expand...
Click to collapse
See sticky post in this forum:
http://forum.xda-developers.com/showthread.php?t=282073
pof said:
You have bootloader 1.06.
In short, you can't... but please read the wiki, and search this forum before asking.
Click to expand...
Click to collapse
thank you, if i`m understanding you i must flash with ROM O2_1.25.207.1_GER.exe am i right ?
but what is the difirence from the two ROM ?!
German Versions (GER)
O2 Germany German http://dict.leo.org/de.gif O2___102 1.25.207.1 07/26/06 ?? 1.07.03.10 32.41.7010.02W 14955.2.3.0 1.04 Download Thread
O2 Germany German http://dict.leo.org/de.gif O2___102 1.25.207.2 12/??/06 ?? 1.07.03.10 32.41.7010.02W 14955.2.3.0 1.04 Download Thread
but if the phone can not start Windows how can i connect it to Activesync, so i can connect it to ROMUpgradeUt.
I have tried flashing from SD with HERMIMG_O2_1.25.207.1_SHIP.nbh renamed to HERMIMG.nbh, but when the Xda tried to check the file it shows
"0020002
Not allow"
WorldMaster said:
thank you, if i`m understanding you i must flash with ROM O2_1.25.207.1_GER.exe am i right ?
Click to expand...
Click to collapse
If your CID is O2___102, yes. But most probably you have a corrupted CID, I can't say for sure because you did not provide any USB monitor capture as advised on the wiki upgrading problems.
WorldMaster said:
but what is the difirence from the two ROM ?!
Click to expand...
Click to collapse
On the wiki, last column is a link to the rom thread on the forum. look at it: http://forum.xda-developers.com/showthread.php?p=1072922
"No changes except HSPDA enabled."
WorldMaster said:
but if the phone can not start Windows how can i connect it to Activesync, so i can connect it to ROMUpgradeUt.
Click to expand...
Click to collapse
1st thing RomUpgradeUt does is killing activesync and put device in bootloader mode... you don't need activesync to do a rom upgrade, you can start it from bootloader.
WorldMaster said:
I have tried flashing from SD with HERMIMG_O2_1.25.207.1_SHIP.nbh renamed to HERMIMG.nbh, but when the Xda tried to check the file it shows
"0020002
Not allow"
Click to expand...
Click to collapse
This almost confirms that your CID got corrupted... you'll probably need to send the device to service centre.
This has also happened to me, and I've tried everything to recover my device. There seems to be no way to fix this problem but to replace the main board.
The only other possibility is to cook a rom (which is far far away) and skip the CID check.
pof -> I'm still waiting for the fix.. hehe
axiom said:
here seems to be no way to fix this problem but to replace the main board.
Click to expand...
Click to collapse
I guess it is not needed to replace the main board, in the service centre they should fix this with a special sd card.
axiom said:
The only other possibility is to cook a rom (which is far far away) and skip the CID check.
Click to expand...
Click to collapse
the CID check is done in bootloader, a cooked ROM (which is not that far away) will not help: The ROM can be cooked and the CID set to whatever value you like, the problem is that it can't be signed with the proper keys, so you have a ROM "matching" the corrupted CID but if it's not signed you can't flash it.
axiom said:
pof -> I'm still waiting for the fix.. hehe
Click to expand...
Click to collapse
If you or somebody else want to send me a cid-corrupted device i'll be glad to investigate, otherwise is very difficult that I can know how to fix this without physical access to the bricked device...
Help!!
I not down boot loader from 1.06-->1.04. I user Herm300, when power then "no gsm" and not boot to window. Please help me.
HTC touch dual手机，刷了hardSPL 1.16 后反复刷了英文和简体中文版本都正常，今天试着在三色屏下，用 MTTY下执行了 task 2a 后，手机再起不来，也进不了三色屏，用数据线连接到计算机后，有提示找到硬件，但是一直提示查找驱动程序！进不了三色屏，也就刷不了ROM，怎么办呀？
English please! i don't understand this :s
gswangmd said:
HTC touch dual手机，刷了hardSPL 1.16 后反复刷了英文和简体中文版本都正常，今天试着在三色屏下，用 MTTY下执行了 task 2a 后，手机再起不来，也进不了三色屏，用数据线连接到计算机后，有提示找到硬件，但是一直提示查找驱动程序！进不了三色屏，也就刷不了ROM，怎么办呀？
Click to expand...
Click to collapse
HTC touch dual (P5520)
1. try to connect with MTTY via USB and type "task 2a" and "ResetDevice" reboot Nike,but device is dead!
You stay in Bootloader?
If yes ... MTTY type "boot"
If it doesnt work ... flash a full Rom or try via OEMSBL and MTTY "cego"
Arrgh, task 2a formats aARM flash
If your device is security unlocked it can be easily unbricked.
If not you will have to contact me for further steps (preferrably in english)
jockyw2001 said:
Arrgh, task 2a formats aARM flash
If your device is security unlocked it can be easily unbricked.
If not you will have to contact me for further steps (preferrably in english)
Click to expand...
Click to collapse
1. My NIKI maybe security unlocked.
2. Connect to Windows ,but prompy me to install 3 drivers.
My Question: How to flash ROM and make it normal. Please give me detail help message!
gswangmd said:
1. My NIKI maybe security unlocked.
2. Connect to Windows ,but prompy me to install 3 drivers.
My Question: How to flash ROM and make it normal. Please give me detail help message!
Click to expand...
Click to collapse
Check your PM and reply to me
jockyw2001 said:
Check your PM and reply to me
Click to expand...
Click to collapse
What PM?
P5520 OR NIKI 100?
jockyw2001 said:
Check your PM and reply to me
Click to expand...
Click to collapse
With MTTY and task 2a
My pda maybe stucked into OEMSBL: NO Os, No Radio and NO BOOTLOADER to load!
1. with MTTY via USB and type "task 2a" and "ResetDevice" reboot Nike,but device is dead!
2. Now, it doesn't respond to any of the buttons on the phone. Connect to Windows , always prompy me to install 3 drivers.
I think the phone is stucked into OEMSBL: NO Os, No Radio and NO BOOTLOADER to load. How to make it normal?
Now nike fault as follows:
1. Automatic entry into the boot (send + camera) engineering qualcomm mode
2. Do not show
3. Computer display driver to be installed, the installation msm7200 drive ok
4. Mtty open com8 (qualcomm diagnostics interface 6000 com8)
5. Not unlock,
Now only supports the following orders, testing various orders, but not retire this engineering model
Radata
Powerdown
Setboot
GO2AMSS
Rseed
Pmic_vib_off
Pmic_vreg
Pmic_level
Pmic_vib_on
Rpass
I also tested with kaiser(p4550) orders "setboot 1" it is not a show, but set back on the normal "setboot 0"
jockyw2001, come in pls!
try my mind
看得明中文？关机的情况下按住相机键（camera key）,然后插上USB，手机就会开机并进三色屏，或者按住相机键，再按电源开关，然后就可以再刷机了，要刷一个full rom。
用mtty有反映，
reboot是不行的提示Invalid command : reboot
cego也不行，提示Invalid command :cego
setboot有反映，提示ARM9BootMode:1
rseed也有反映，提示HTCS6B60C2B012B8E95520B0F4852802B89E*;ÔHTCE
其他就不知道怎么搞了。
手机买来时已经刷了hardspl，是否解锁还不太清楚，根据现在的情况看来，可能没有真正解锁。
看来kaiser买来时还是要自己先解锁再使用，免得出现真砖。
还是期待高手出现，不想寄回原厂，暂时使用830。
cantonese said:
看得明中文？关机的情况下按住相机键（camera key）,然后插上USB，手机就会开机并进三色屏，或者按住相机键，再按电源开关，然后就可以再刷机了，要刷一个full rom。
Click to expand...
Click to collapse
试过了，没有用！
Who can help me?
gswangmd said:
Who can help me?
Click to expand...
Click to collapse
No unbricker in the moment!
NetrunnerAT said:
No unbricker in the moment!
Click to expand...
Click to collapse
Who can help me?
I'm a long time lurker but I think that if jockyw2001 can't help you then your device is dead. Maybe the frankenkaiser unbricker tool can help you now - again jockyw2001 will know about that (it's his tool i think) or maybe netrunnerat.
Hi
I tried to update my MDA2 to WM 6.5. the update faild. Now the screen of the MDA just shows Serial/USB on the top and v1.06 on the bottom if I try to load the update again a conection error occurs.
I already took the battery out for 24h but it did not chance the prblem
what can I do to solve the problem
Thanks for the support
hay man removing battery can't solve ur problom.
you have to try flashing with sd card method. or else just remove all your usb drivers and put your device in bootloader mode & then it automatically ask for installing drivers.
caution ::: remove active sync & then do the above procedure.
good luck
Can you give as a link or procedure how to flash HIMALAYA on SDCARD...
TnX
http://wiki.xda-developers.com/index.php?pagename=HimalayaBootloaderSdCardFlashing
Rudegar said:
http://wiki.xda-developers.com/index.php?pagename=HimalayaBootloaderSdCardFlashing
Click to expand...
Click to collapse
Thx for this Boss...
But One thing here is....
Can you elaborate how to do this?
first copy the first 3 M of the radio to sd
d2s 60000000 00300000
Click to expand...
Click to collapse
Where do I get the 3 M?
Cause as I understand here... Using Mtty on USB> i will type ( password BOOTLOADER ) then press enter.... And it shows me like this...
USB>password BOOTLOADER
HTCSPass.<YHTCEUSB>
USB>d2s 60000000 00300000
pc->drive.total_lba=EF700
pc->drive.num_heads=8
pc->drive.sec_p_track=20
pc->drive.num_cylinders=EF7
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=CFFC
pc->drive.drv_type=0
pc->drive.securedAreaSize=2800
pc->drive.securityDrv=5
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=1DEE0000
SDCARDD2S+,cStoragePlatformType=FF
************
Store image to SD/MMC card successful.
USB>
Click to expand...
Click to collapse
Is it right???
Thanks for ur understanding....
bR
phone have spl-1.16(was in phone,i don't make hardspl) but when i try write an cooked rom phone stop at 75% and now start in bootloader with power on+camera buton, with power on buton phone start in white screen and one vibration.
i try something with mtty but i don't understand very goog the procedure,i need a memory card insert in phone or without memory card?
when i start mtty and write first comand:
Cmd>password BsaD5SeoA
Pass.
HTCST ÚÈÒHTCE
Cmd>
i don't know what do now
can help me somebody?
thanks
nobody can help me?
iugo said:
nobody can help me?
Click to expand...
Click to collapse
I can try, can you tell me what is written in your bootlader and stop using mtty.
Regards,
in left screen writte:
NIKI100
SPL-1.16.0000
CPLD-4
and in down screen write SERIAL without cable in phone and when i insert cable in phone write USB
iugo said:
in left screen writte:
NIKI100
SPL-1.16.0000
CPLD-4
and in down screen write SERIAL without cable in phone and when i insert cable in phone write USB
Click to expand...
Click to collapse
Thanks, just download This rom after download just connect you're phone to your computer, make sure your phone is in bootloader and run the exe from the download this will flash the original rom, if everything is ok, you will have the original wm 6.1 rom after that you need to Hardspl your phone, just read this Thread.
Just keep me informed if the original rom can not be flashed.
Succes buddy
dont'n work ,stop at 1% after that phone restart in white screen. i attached file with error.
In which language was your original rom ?
before was in italian language
iugo said:
before was in italian language
Click to expand...
Click to collapse
Here is the link for Italian, try to do the same as I mentioned before, just make sure active sync or wmdc is turned off.
Greetz,
thanks man,with that rom phone work, now can instal hardspl 1.22? is ok that hardspl?
iugo said:
thanks man,with that rom phone work, now can instal hardspl 1.22? is ok that hardspl?
Click to expand...
Click to collapse
Yep buddy, that's ok, now you can do the Hardspl as I mentioned before, just read carefull.
Succes,
now work with new rom cooked, i see in phone gps antena,have integrated gps antena? wi-fi suport?
iugo said:
now work with new rom cooked, i see in phone gps antena,have integrated gps antena? wi-fi suport?
Click to expand...
Click to collapse
Perfect it worked for you, enjoy your cooked rom, and sorry no wifi, the gps is for communication with an external gps receiver.
Greetz,
ok, thanks for your help.