Related
:?: I know how to alter the voice mail speed dial number via the network setting. I can put in my account number and password and set delays with the 'p'. But both my pw and account number need to be followed by a "#".
When I put "#"'s into the network settings they get tossed away when its sent to ATT. Anyone solved this problem with their sx56?
Chris
Hi,
Since I sync my X01HT with my PC outlook,
the phone number is my contacts looks like:
+81 3 12345678.
If I dialed this one directly, I got an error voice message.
The SB cannot recognize "+" sign.
Should I use some software to change this number automatically to:
03 12345678?
By the way, I can use this number well in Taiwan or China.
s2k7 said:
Hi,
Since I sync my X01HT with my PC outlook,
the phone number is my contacts looks like:
+81 3 12345678.
If I dialed this one directly, I got an error voice message.
The SB cannot recognize "+" sign.
Should I use some software to change this number automatically to:
03 12345678?
By the way, I can use this number well in Taiwan or China.
Click to expand...
Click to collapse
i don't know if there is any software that can automatically do it for you but you can't dial + when you are making calls from japan and numbers need to be changed to the 03 12345678 format you mentioned. what i did is manually added those in each contact as an alternate phone number so that i can pick and choose the one appropriate depending on where i am.
Try dialing +81312345678 manually, then you will know if it is a problem with your contacts or a total incompatability with the network.
kevino said:
Try dialing +81312345678 manually, then you will know if it is a problem with your contacts or a total incompatability with the network.
Click to expand...
Click to collapse
i said that doesn't work when you are calling from japan. you have to apply for the international calling service first if you want to make international calls, but even with that using + plus the country code doesn't work in japan.
http://mb.softbank.jp/mb/en/global_service/international/call/index.html
harryk1372 said:
i said that doesn't work when you are calling from japan. you have to apply for the international calling service first if you want to make international calls, but even with that using + plus the country code doesn't work in japan.
http://mb.softbank.jp/mb/en/global_service/international/call/index.html
Click to expand...
Click to collapse
Thank you harryk1372 for your suitable comments.
This is why I want to find some soft to change the "+" for me automatically.
One can use "+86" in the China Telecom network.
I tried "dialDTMF", but nothing happened.
I fight this since I am in Japan, but once again, one man against the Japanese bureaucratic world... Anyway things which drives me nuts is that while you have to dial 010 for call, SMS use the international dialing system with +
http://mb.softbank.jp/mb/en/global_service/international/message/sb3g/index.html
Now how hard can it be for Japan or SB use an international standard... like this dammed + ?
Or if they love so their uniqueness (their 010) why could not they simply tweak their system to accept both 010 and +
Daimaou said:
I fight this since I am in Japan, but once again, one man against the Japanese bureaucratic world... Anyway things which drives me nuts is that while you have to dial 010 for call, SMS use the international dialing system with +
http://mb.softbank.jp/mb/en/global_service/international/message/sb3g/index.html
Now how hard can it be for Japan or SB use an international standard... like this dammed + ?
Or if they love so their uniqueness (their 010) why could not they simply tweak their system to accept both 010 and +
Click to expand...
Click to collapse
exactly... why the hell they need to use 010 for voice calls when they can accept + for sms. they should consider accepting + for voice as well.
Someone might like to take a look here.
http://www.nicque.com/PQz/
I've been using the generic installation on my X01HT and it's the best work around I've found.
All my contacts from Outlook have full numbers including country codes with "+".
In the Country Code options I have a Japan International setting that adds 010 with the Convert + and remove - options checked.
When I select a Japanese contact, in Japan, I toggle the Int'l Access off to get no country codes.
For a Japan based International call I toggle the Int'l Access on (the country code appears) and then the Int'l Calling to select the Country code option to add 010.
It sounds more complicated than it is, but anyone who has had a call in, cursed they can't copy/paste a number and add 010 etc will find it a blessing.
There is no information on the author so take care, but I don't think it is doing anything malicious.
How to configure Internet Settings/MMS in cingular8525? Is there a cab files to install?
try telling people what network and country your in then maybe somebody can help and there is a search function on this site, try to search for network setup wizard
scousemartin said:
try telling people what network and country your in then maybe somebody can help and there is a search function on this site, try to search for network setup wizard
Click to expand...
Click to collapse
I'm from the philippines and on Smart Network and hope there is someone can help me, Tnx.
Dont know if these will work but found them on another site so see if they do by giving it a try
Here’s a quick tip on how to activate your phone’s MMS and GPRS settings if you’re with the Smart Communications Philippines network:
How to Download MMS and GPRS settings from Smart:
To download SMART MMS phone settings:
Key in SET MMS
and send to 211.
To download SMART GPRS phone settings:
Key in SET GPRS
and send to 211.
Example: If you have a Nokia 6230, that’s “SET MMS N6230”
To activate SMART GPRS:
Key in “GPRS ON” and send to “333″
To activate SMART MMS:
Key in “MMS ON” and send to “333″
Note :
The configuration settings will be sent to your phone. You will need to select “Save All” to save the settings in the phone. Some MMS and GPRS handsets already have pre-loaded phone settings.
Activation of MMS and GPRS will require a confirmation message from SMART. A message will be sent to the sub once the feature has been activated.
Step 1:
Text SET 3G to 211, you will then receive the phone settings. (Ex: SET 3G N6680)
Step 2:
Go to the SMART 3G Portal: http://wap.smart.com.ph/3G
or click on the SMART 3G link on the SMART WAPsite.
Step 3:
Click on the link of the service you want to access.
scousemartin said:
Dont know if these will work but found them on another site so see if they do by giving it a try
Here’s a quick tip on how to activate your phone’s MMS and GPRS settings if you’re with the Smart Communications Philippines network:
How to Download MMS and GPRS settings from Smart:
To download SMART MMS phone settings:
Key in SET MMS
and send to 211.
To download SMART GPRS phone settings:
Key in SET GPRS
and send to 211.
Example: If you have a Nokia 6230, that’s “SET MMS N6230”
To activate SMART GPRS:
Key in “GPRS ON” and send to “333″
To activate SMART MMS:
Key in “MMS ON” and send to “333″
Note :
The configuration settings will be sent to your phone. You will need to select “Save All” to save the settings in the phone. Some MMS and GPRS handsets already have pre-loaded phone settings.
Activation of MMS and GPRS will require a confirmation message from SMART. A message will be sent to the sub once the feature has been activated.
Step 1:
Text SET 3G to 211, you will then receive the phone settings. (Ex: SET 3G N6680)
Step 2:
Go to the SMART 3G Portal: http://wap.smart.com.ph/3G
or click on the SMART 3G link on the SMART WAPsite.
Step 3:
Click on the link of the service you want to access.
Click to expand...
Click to collapse
I've tried these steps and it replys acivated but still I can't connect to internet. Is there a cab file for automatic settings configuration? Or something like automatic data connection like in smartphone?
Yeap thats right three days with Network Support and they can not figure out why my phones not updating. Anyone else have any ideas before i myself agree with them that it is my equipment and toss it on ebay
It is a Alltel 6800 that has the Opal2.40 loader with the New Verizon 3.57 Update
Any ideas are better than anything i have at this point my mind is tired.
Forgot to mention tech support asked me to go ahead and clear the storage and reflash the verizon update again so i am at Verizon Factory Defaults other than I have changed the SID to match the local Verizon SID
what are you trying to do?
I am just trying to get Data Access for Pics and Video messages as well as Web Access .... The phone works for Voice calls and will send and recieve regular txt but anytime it Dials into #777 it comes back Error 11 PPP Connection Error
I have went into the ESPT and checked my secuirty and its [email protected] and vzw so thats ok.....the techs say that my phone is not updating its key its been soft reset and hard reset more times in the past 3 days than i have had sexual relations with anyone other than myself
well lets solve one problem at a time. first, the sexual relations issue. go get yourself laid a bunch of times and then we can continue working on your phone.
i'm not sure about this MyMDN business, but your mdn is your phone number. your credentials for the data connections should be your 10 digit phone number:
##########@vzw3q.com
password is vzw.
also, check your vzw mdn registry key and make sure it is set to your 10 digit phone number
[HKLM\Software\Arcsoft\Arcsoft MMS UA\Config\mm1\wspheader]
X-VzW-MDN should be your number
I'm married...think thats my problem on the first one someone told me the ring goes on the nice things about her go away
yes my phone number is what i ment by mdn @vzw3g.com
also i am a newbie on the registry so i will have to report back to you on that when i have time to download the software for the registry
ok i followed HKLM\Software\Arcsoft\Arcsoft MMS UA\Config\mm1\wspheader] and i have no entry for X VzW MDN
I have
Accept
Accept-Charset
Accept-Language-
User-Agent
x-wap-profile
Since that phone was Alltel to start, has Verizon ADDED that ESN to their database??? Most likely they haven't..... The ESN is the Equipment Identification Number. My understanding is that it gets sent when a data connection is initiated. The MDN(Mobile Directory Number)@vzw3g.com will work but I suspect the ESN is not validating.....
EDIT - Humm, I didnt even see your response above.... So add the Key above and see what happens....
Here's what that section should look like...
"User-Agent"="utstar68kv1"
"Accept"="application/vnd.wap.multipart.related"
"x-wap-profile"="http://uaprof.vtext.com/utstar/xv68k/xv68k.xml"
"X-VzW-MDN"="your 10 digit cell number"
"Accept-Charset"="us-ascii;utf-8;iso-10646-ucs-2;iso-8859-1;gb2312;gb13000"
"Accept-Language"="en"
...
yea i spent all of last week waiting on the to validate the ESN which they finally did waiting long enough is the key it just took them a while to get the ESN in the system and show a VX6800 and set-up all the "pervision" to match my phone (i know that is off in spelling)
Ok I added that string into the reg and did a soft reset and check the value to make sure it stayed and it did and I still get error 11
all i needed to enter was my telephone number not the @vzw3g.com on the end correct?
chanderson said:
yea i spent all of last week waiting on the to validate the ESN which they finally did waiting long enough is the key it just took them a while to get the ESN in the system and show a VX6800 and set-up all the "pervision" to match my phone (i know that is off in spelling)
Ok I added that string into the reg and did a soft reset and check the value to make sure it stayed and it did and I still get error 11
all i needed to enter was my telephone number not the @vzw3g.com on the end correct?
Click to expand...
Click to collapse
Here, I made you a cab to add the necessary info minus your cell number since I don't know it..... So here's what you do.
1. go into the registry and delete what you added. Hence - Delete whatever is listed under the WspHeader....
2. Run this cab.
3. Go back to WspHeader and change the X-VzW-MDN key from the 10 X's that I put in to your cell number.... ie: 1234567890, then exit the reg editor and reboot....
EDIT - The info in that cab came straight from MY registry.... Minus my cell number.....
Let us know...
ok cleared the reg...installed cab
reset
changed your xxxxx to my number and still ppp error 11
Have you tried to install DCD's carrier cab? I'd try that next, then reset.....
Get the Verizon carrier cab here
http://dcd1182.n715dp.com/index.php?dir=carriers/&download=dcd+Verizon+Carrier+20081031.cab
are u running a custom rom? try running dcd carrier cab, i have used it to fix a few phones i had switched to different carriers and data didnt work
Ok, quick question as i am new to the flashing never really tried any until now was too scared until Alltel screwed me by selling out.
Can i just put this on my card and run it from inside WM6.1?
Hey, i had this problem in the past. First let me say that i am not an HTC guru like most people here, so research anything i have to say.
Sounds like everything obvious is set correct, take a look in EPST. Dial ##778, select edit (but be careful not to edit anything, if you select view it will not allow you to see the needed information). It will ask for a security code, it is 000000. After it loads select view info, then Security.
The following information should be present.
HDR AN AUTH User Id : [email protected]
HDR AN AUTH Password : encrypted data characters
PPP User ID: encrypted data characters
PPP Password : encrypted data characters
S.IP DUN User name : [email protected]
In my case there were no encrypted data characters in the appropriate places.
The easiest way to resolve it from what i've read is to activate another device on your account then switch back to the desired unit. In my case i had to convice VZ Customer Service to completely reset my account. I believe there's a DMU code somewhere also that has to be 10. Search for PPP error code 11 security and i think you'll find something.
i got
HDR AN AUTH User Id : my#@vzw3g.com
HDR AN AUTH Password: a few numbers looks like my HEX ESN
PPP User ID: my#@vzw3g.com
PPP Password : vzw
S.IP DUN User name : my#@dun.vzw3g.com
I have another phone i could swap too and then swap back....its easy with verizon you just dial *228 and press 3..put in your phone number and last four of your ssn and your done
tried the swapping of the equipment and that didnt work...it did however get on line one time and i closed it and tried to connect again just to get the Error 11 again
Search for PPP error code 11 security, choose the "waiting for a dmu reset", i don't know how to embed it. That thread contains what i did to correct my problem.
Maybe the they are verizon specific, but your settings do not match mine nor any other xv6800 i have owned.
I have an idea, follow the instructions for the TP and getting EVDO on it.
Don't try this until you ask a few people first.
I have an idea, follow the instructions for the TP and getting EVDO on it.
Don't try this until you ask a few people first.
ok...here is my update on status...
Still no Data, BUT
When i was on the VZW Update ROM i had info in the following fields
HDR AN AUTH Password:
PPP Password
also
in the MIP default i had data under
AAA Shared Secret, and HA Shared Secret
NOW I used the latest dcd_titan_3.3.4.exe and I have nothing in these spots except 0000..ect under HDR AN AUTH Password
i went back to my LG 5500 and took allllll data off of my account waited like 4 hours and swapped back and still nothing.
only thing now is i think i will go back to the VZW Rom and call for a DMU reset and beg some more
I had the exact same problem after flashing to DCD 3.2.6. I had to call Verizon and have them generate a new A-key (26 digits).
You might have to call back a bunch of times or press the rep you get to generate the key for you (any of them can, they just don't know how).
Not sure why a new A-key would fix that problem, but I fought with it for quite a few days before finally getting it figured out. The data has worked flawlessly on my phone ever since.
Post back if this works if you would.
Hi,
I purchased HTC Touch Pro (US Cellular CDMA). I want to use it with Mumbai MTNL Garuda Mobile Phone service in Mumbai, India.
I don't know much of cell phone flashing and reading web pages would like to get this done.
1) How do I check my phone needs what ROM and which one is it already using ? I assume ROM is like BIOS and windows mobile is like win xp os. So installing ROM will not affect windows mobile. do I have to flash rom for a specific carrier\service provider ?
2) How do I check whether my phone in unlocked since this is CDMA and has no sim card ? In ebay ad said it was unlocked.
3) How do I find roms for "mumbai garuda mtnl". You can google the quoted string for information on service provider. I don't see much helpful info on site and the service provider is not helping. It is open to questions if I have any so let me know if you want me to ask them. can one check compatibility between US cellular and MTNL garuda mobile cdma network so I know I can use the phone.
4) Please enumerate high level steps with some pointers for me to follow through the install process.
5) is the handset supporting 3G since I see its network specs as:
Network US cellular:
Dual-band (800/1900MHz), CDMA2000 1xEVDO Rev. A/1xRTT and IS-95A/B voice or data with up to 1.8 Mbps up-link and 3.1 Mbps down-link
MTNL Garuda mobile network is CDMA-1x. Another MTNL 3G Jadoo is 3G (WCDMA, HSDPA).
so compatibility wise can I use the US cellular handset on MTNL ?
CDDMA-1x and CDMA2000 1xRTT are same so I suppose handset should be usable.
6) when switching carrier is it simple as registering your new handset with new carrier ? is there standard process for it like call in their network using some special number and type in your existing number which you have with their network. ex. if I have 20337444 number on MTNL network then on HTC Touch Pro I dial in some special number for MTNL network and then key in my existing 20337444. This will register the ESN on their network and I am all set.
7) the MTNL guy said that first check if dialing *228 gives you MTNL network. If so then go to customer service and get more help. When I dail I don't think it does any thing. It gives 3 beeps and returns to home screen.
Additional info MTNL gave was they use channels primary 185 and secondary 226. I am not sure what these channels mean.
Regards,
i dont beleive you have to flash any specific rom to get your carrier to work, but you will have to google for "carrier cabs" + your provider name to find what will work for you
to see if your phone is unlocked take the back off the phone, pull the battery, and then put the battery back in, hold the volume down button and press power till the phone turns on, i beleive it will say something like "security unlocked" if the phone is unlocked, after you check that just pull the battery and put it back in once again and start up your phone to get back into windows mobile(not holding the volume down button this time)
as far as roms for the mtnl garuda, any rom will work, i reccommend the energyrom, google energyroms.com, cdma seems to be cdma anywhere you are, if it says cdma it should work in theory
your handset will support 3g, the us cellular version of touch pro supports 3g
for the mtnl garuda carrier to support your phone, you will have to see if they will accept your meid or esn under the battery, here in the USA verizon wont accept sprint esns, and vice versa
sorry i cant be more helpful, but hopefully somewhere through this i have helped you, good luck!
whoshotjr2006 said:
i dont beleive you have to flash any specific rom to get your carrier to work, but you will have to google for "carrier cabs" + your provider name to find what will work for you
to see if your phone is unlocked take the back off the phone, pull the battery, and then put the battery back in, hold the volume down button and press power till the phone turns on, i beleive it will say something like "security unlocked" if the phone is unlocked, after you check that just pull the battery and put it back in once again and start up your phone to get back into windows mobile(not holding the volume down button this time)
as far as roms for the mtnl garuda, any rom will work, i reccommend the energyrom, google energyroms.com, cdma seems to be cdma anywhere you are, if it says cdma it should work in theory
your handset will support 3g, the us cellular version of touch pro supports 3g
for the mtnl garuda carrier to support your phone, you will have to see if they will accept your meid or esn under the battery, here in the USA verizon wont accept sprint esns, and vice versa
sorry i cant be more helpful, but hopefully somewhere through this i have helped you, good luck!
Click to expand...
Click to collapse
thanks for reply. I searched for "carrier cabs mtnl garuda" but no good results.
I learned from specs the model is RAHP800. does it mean that it will not work on MTNL garuda ?
MTNL garuda CDMA carrier cabs
Hi,
can some one provide carrier cabs for MTNL garuda CDMA (no RUIM) along with install instructions. would be nice if you have activation instructions. how do I get *228 to connect me to MTNL network ?
a touch pro 800 is the sprint cdma touch pro, and about the cabs sorry man i have no idea, usually when i call boost mobile to activate a new phone i provide them with my numbers from underneath the battery, and they will give me the msl code to enter epst and change the msid and mdn, maybe you could call your carrier and ask for the msid and mdn? as far as getting your msl code, as long as you have the microsoft .net cf 3.5 cab installed on your phone you can use a program called "baf msl grabber" to get that code
good luck, hope you figure something out, and if you need anything else feel free to contact me
Do you know anyone else with a TP runnon that same network? Maybe you can get some files from their phone.
the terms you used are new to me like "msl code to enter epst and change the msid and mdn".
You state "msl code to enter epst and change the msid and mdn," and use "baf msl grabber" to get that code. The MTNL garuda mumbai service folks I talked to are not willing to give any details. They in fact are just not supporting any handset other than what they provide. Now they are discontinuing new cdma handsets which are not using RUIM card (they say its similar to sim card).
can you guide me to some article which has instructions and explanation of various steps we might take to get things done like ones we have on eHow.com.
Regards,
jasew503 said:
Do you know anyone else with a TP runnon that same network? Maybe you can get some files from their phone.
Click to expand...
Click to collapse
I do not know of any such user. can you guide me to simple article which expalins the steps involved in doing any programming / install of cabs etc. I have not much idea about cdma programming.
Regards,
Installing carrier cabs and flashing roms wont make the phone work on the network you want it to. The first thing you need is to change the PRL on the device to one that works with your carrier. This a file file you may be able to download, or get it from someone elses phone who uses the same carrier. After that, you will need to program all your info into it, MDN, ect. Then hopefully your carrier will even allow the ESN on their network. Did you say this was a US Cellular device?
Hi,
I learned from service provider that need to disable PRL and then use programming code so can feed in information. So for US Cellular HTC Touch PRO CDMA (no sim/ruim) can one provide programming code\dial codes ?
Do I need activation code in order to be able to enter into programming mode ?
Here is some reference for it: http://support.sprint.com/support/a...e-vw371511-20090807-140419?&INTNAV=SU:DP:HDIB
I would like to program my phone and when I dial ##778# and make a call it just ends. I am not sure how to enter the progam mode. Please guide.
There isn't a master list or anything like that. I used to flash phones to cricket and the 2 TPs I've flashed from us cellular were problematic. Could have been a coincidence. You need to obtain the PRL.
Sent from my MSM using XDA App
HTC Touch Pro unlock and program code
Hi,
I dialed ##000000 and it now put me into EPST (Activation Wizard(MSL)) screen. I guess I have made some progress and I see MDN, MSID, Home SID/NID #1.
It seems all sprint code listed here http://www.pcoperative.com/ppc/htc_tp_dial_codes.htm
works just that no need to key in ending # for each code.
Well how to check that phone is unlocked. I dialed ##775 to update PRL and it prompted me for unlock code.
I purchased phone from ebay and the ad mentioned that its unlocked.
is unlock code same as SPC/MSL unlock code ?
I went into bootloader and it shows Security Unlocked.
Why does it prompt me for unlock code when I go to ##775 to update PRL ? what to do so I can disable PRL ?
Few other codes like ##DEBUG and Advanced EPST show me information fine without prompting for any unlock code.
Regards,
You haven't made any progress at all unfortunately, you still need the prl. Any codes you enter that allow you to MODIFY phone settings will require an unlock code.
Sent from my MSM using XDA App