usb driver.zip for wi modem
Installation of HTC USB modem driver into Windows XP
I am sorry to bother here, unfortunatelly, I have a problem. I can not install the USB driver into Windows XP on my PC. If I open an inf file, no modems are listed. I have Win XP home CZ (Czech). What could be a problem? Bad driver? Is there another driver? Thank you very much for your answer.
Novka
unfortunately
these are for an XDA II ... so we are still at the
"How can we use XDA I as a wireless modem on WM2003 (except the DE version) ?" stage.
Anyone has options or solutions. I hate to carry another GPRS phone along the XDA just to connect my laptop.
xda-modem
you can look at : http://www.myxda.com/downloads/swupgrade/setup modem_win2k.pdf
Re: xda-modem
donnyriyadi said:
you can look at : http://www.myxda.com/downloads/swupgrade/setup modem_win2k.pdf
Click to expand...
Click to collapse
This is a great howto document but my understanding is (and I have checked on my PPC) their is no wmodem.exe software.
The problem is as follows.
The entire wmodem is using rilgsm (and the radio software part) in order to work.
So from this poin it is impossible to make it happen.
What I suggested, but since my PPC programming skills are low, is to find a program that simulates a proxy on our XDA. Meaning that the XDA is used as a gateway from the computer.
The proper definition is, i think, "reverse passthrough".
The starting point can be the Remote Control software that display the XDA image on PC ...
Anyone has seen such app ... or has it in development ?
Decebal
wireless modem
i had a standard german rom as i bought my xda, and there was also no wireless modem app.
but if you install another rom, like the wm2003 one, or the special rom from xda-developers, the wireless modem app is already installed.
my problem is, when i connect my modem after a while(about 15-20 minutes) or if i open more than one webpages at the same time, the modem doesn't work anymore, and i have to reset my xda. I have tried with another handphone(nokia 6800) and it worked properly. Does anyone knoe why this happened ?
The starting point can be the Remote Control software that display the XDA image on PC ...
Anyone has seen such app ... or has it in development ?
Click to expand...
Click to collapse
there is one from microsoft. its called remote display control. but it only work with activesync, and if the activesync connected to xda, the internet connection from the xda won't be used, instead the xda will try to connect via your pc.
Small point... if you look at benmuliono's post it was for XDA2 not XDA1...
HTC USB modem driver
Good day,
about my post, there is a misunderstanding. There is no problem with XDA I or XDA II and wireless modem application (for the present). There is a problem with a driver usbmdm.inf and its installation into the Win XP CZ, because the USBMDM.INF file is not recognized as the driver by my Win XP CZ (HTC USB modem does not appear in installation window).
Thus, if the wireless modem application is running on the XDA, the info "new hardware is detected ..." appears. Then, I want install the modem into the system, but I am not succefull.
I try to make connection with XDA II of my friend, although I am an owner of XDA I (which is shown in left side). That is probably the source of the misunderstanding.
I am looking for somebody who has similar problem or has a working driver for my system and would be so kind to send it to me ([email protected]).
Thank in advance for your help,
Novka1234
xda as modem for laptop
After 3 months and 463 hairs later, I have finally figured a work-around for turning our xda (1)'s into a USB modem for internet access via GPRS. I will have it available for download on my website for only $20.00 beginning 7/20/04. it will be available through PAYPAL only. (I know this is worth a lot more than twenty dollars, but I wanted everyone who wants it to be ablle to afford it.)
how
how can you demonstrate this first.
this is interesting ... but a.f.a.i.k. it is not possible.
are we talking about any WM2003 ROM and only with the wmodem software ?
F.A.I.K.
it will be available for any english wm 2003 rom , (propriatary) software pkg,
I understand the skeptisism, but will not be releasing a demo or trial version. this has always been possible as I understand it, it has just been squashed by the manufacturers and software giant. just a couple more days and everyone will be happy.
DMW
good
this will be indeed great. i'm close to buy an expensive pcmcia GSM card for my laptop but this will be a great alternative.
can you tell me this:
* the pc will use all ports for connexions (not limited lika a proxy) ?
* will the receive function be disabled or when a call comes it just suspend data and allow call ?
* do we need to install software on xda and pc too ?
* are there any inconveniences from your point of view ?
* can you at least post some screenshots or anything "tangible"
* what transfer rate have you achieved ?
Thanks for your ideea and making it practical.
?
i guess that no news is bad news.
so be it!
XDAII i modem failure
hello frns, i am getting a strange error since 2 days it says"error:692,
hardware failure of the connecting modem"
i am using my XDAIIi PPC to access net on my PC. i have installed the HTC
USB modem for the device.
when i run the query it works fine and give erything in success but when i
try to dial it gives me the above error. i was able to connect it before
but now it is not working.
i am having airtel postpaid connection in M.P.
also before i used to get the connection light up in the wireless modem
dialog on my PPC but even that is not there now. please help me with that.
wht should i do to get the net running up again. i there any other drivers
which i should use or what??
usbmodem for xdaIIi
Thank you, got the USBMDM from here. the files above is still working. AFtet install it the setup is done till finish. No problem, it works on my ppc. Now I don't to worry getting into the net via my xdaIIi.
Wow, this is really great. I'm using the MDA Vario to connect to the internet.
Works great!!!
possible fix for "Error 692"
@puneet_84:
I too followed the installation instructions exactly, but had Error 692. After extensive web-searching, found the solution. Hope it works for you - it did for me. (But no guarantee!)
http://www.ppcsg.com/index.php?showtopic=78789
On trial and errors testing out various config changes I found that the key cause of my XP popping out the Error 692 is when I disabled Modem Compression at any end whether one and not the other or both (meaning the setting at modem properties in the Control Panel and the modem properties in the Dialup networking sections).
The fact is Modem Compression must be enabled on the Control Panel modem properties for the HTC USB modem and the modem properties in the corresponding dialup networking configuration.
Click to expand...
Click to collapse
being given a hermes but it is AT&T branded.... it will obviously come without sim and I need to unlock it so can be used on TMO..... will I still be able to do this by connecting it by usb and using the v3a unlocker? Also if there is anything else I should no that I may have missed roaming the threads please let me know.... I currently have an excalibur so am pretty familiar with modifying things.
all gsm phones comes with a sim of sorts
he's being given the phone, so the person giving it to him is probably keeping the simcard?
you should be able to unless the unlocker states otherwise..
the phone is fully functional (bar the phone/texting) without a simcard as its a PDA / Phone
kingsizeriz said:
he's being given the phone, so the person giving it to him is probably keeping the simcard?
you should be able to unless the unlocker states otherwise..
the phone is fully functional (bar the phone/texting) without a simcard as its a PDA / Phone
Click to expand...
Click to collapse
Ok just making sure... also I could not find USA tmobile settings for once it is unlocked to get everyhting working right. I know there is special settings for the excalibur to get MMS and sms working properly so I would assume that hermes would be the same.
I found the keyboard fixes as mine is an 8525(cingular) but I want everything to work right.... If I missed it just link where I need to go for US tmo setup.
I dont mind doing the reading... THANKS!!!
PS..... Obviously I will be changing ROMS too
Is it the same as excal....?
Here are the steps and settings:
Step 1. Setup GPRS connection for T-Mobile network:
Start > Settings > Connections (tab) > Connections > Advanced (tab) > Select Networks > New...
Enter the name for the profile (e.g. T-Mobile), then go to "Modem" tab and click "New...", enter name for the connection (e.g. T-Mobile Data), choose "Cellular line (GPRS, 3G)" in the drop-down menu, click "Next", the access point should be "wap.voicestream.com", click "Next", leave all fields blank on this page, click "Finish". Now go to "Proxy Settings" tab and select "This network connects to the Internet".
Click "Ok" all the way out.
Step 2. Setup MMS:
Start > Programs > Messaging > Menu > Tools > Options... > MMS > Servers (tab) > New
Server name: (you name it)
Gateway: 216.155.165.50
Port Number: 8080
Server address: http://216.155.174.84/servlets/mms
Connect via: (the connection you created in step 1)
Sending size limitation: 300K
WAP Version: WAP 2.0
Click "Ok", set this new entry as default (with a red arrow on the icon).
check out HTC Network Wizard (comes precooked into most roms now..) if not then schaps operator setup
does the leg work for you
Similiar to the excal 6.1 roms then.... I am reading all the new roms now so trying to decide where to go first LOL.... seems all have good and bad... I'll keep wading through them
Looking through all the posts in the forum, I can't seem to find a recent conclusion on PDE information for Verizon. Thus, consolidation time!
If you have your aGPS working well for a custom ROM (ie DCD 3.2.3 and radio 3.42.50) on Verizon, what are the aGPS registry settings and QPST settings you're using?
Panth said:
Looking through all the posts in the forum, I can't seem to find a recent conclusion on PDE information for Verizon. Thus, consolidation time!
If you have your aGPS working well for a custom ROM (ie DCD 3.2.3 and radio 3.42.50) on Verizon, what are the aGPS registry settings and QPST settings you're using?
Click to expand...
Click to collapse
I just actually did this today to get aGPS working again. All credit goes to serfboreds & RyanMogul6800 @ XDA and Shadow-Tech @ PPC
Reverting back PreGPS Verizon if you had MR1/MR2 Stock ROM (If you've already done this skip this step)
QPST & Registry Settings Reference Link
----------------------CONNECTING OUR PHONE TO QPST---------------------------------
1. Run Wmodemdriverinstaller.exe on your PC (This will install the DIAG driver)
2. Click install drivers, wait, once it says completed just close window
3. Install qpst_2.7b215.exe on your PC, next click through it
4. On Phone dial ##3424 , then plug it into USB port, WAIT TILL ALL DEVICES ARE INSTALLED (WAIT A GOOD 60 SECONDS)
5. Open Windows Device manager (right click on My Computer, click 'Properties', Click 'Hardware' Tab, 'Device manager' Button) on PC
6. Expand the item called 'Ports (COM & LPT)' on PC
7. Look for an item called 'HTC Diagnostic Interface' record what COM PORT it is. (see PIC below) Your COMM Port may not be the same.
8. On PC click start\All Programs\QPST\QPST Configuration. Click 'Ports' Tab. Click 'Add New Port' Button in lower right.
9. Click on the Device with the same COM port from as the 'HTC Diagnostic Interface' then click OK. (You may need to manually enter it. use COMX, i.e. COM6. description is COMX, i.e. COM6) see pic
10. Click 'Active Phones' tab. click 'Start Clients' drop down, then click 'SERVICE PROGRAMMING'
11. Click 'OK' in 'Phone Selection' window (code is 000000) see troubleshooting if it fails
----------------------------------------------------------------------------------------
-------------------------APPLY THE FIX-------------------------------------------------
1. Click 'Read from Phone' button in bottom left corner
2. Click 'Save to File...' button don't change name and save to your desktop. (just to have a backup)
3. Scroll over to 'gpsOne' tab (upper right corner)
4. Click all the check boxes on the left hand side so they are all blank. (all 9, See pic)
5. THEN Click all the boxes so they are checked. (all 9) (yes it's strange)
6. At 'PDE IP Address' enter: 216.198.139.92 -
7. At 'PDE Port Number' enter: 8889
8. At 'PDE Transport' select: IP
9. At 'Position Calculation' select: mobile
10. Click 'Write to Phone' (lower left corner)
11. Once completed, enter ##3424 on the phone again
12. Tap exit, then 'Yes' button on the phone
13. Unplug phone and soft rest
14. Exit QPST. DO NOT SAVE CHANGES
----------------------------------------------------------------------------------------
Installed Telus aGPS cab (or do it manually in the registry)
Which WModem Driver are you using? I have 1.2.1.1 2007.03.07 and it just kind of auto-installs and says it is done, but plugging the phone in after that doesn't present an HTC Diagnostic port in device manager. No devices with a bang next to it, everything is installed.
Dialing ##3424 just gives me a "Your # cannot be dialed at this time..." message. I'm running the 6.5 21501 build right now.
Diag mode
scorp508 said:
Which WModem Driver are you using? I have 1.2.1.1 2007.03.07 and it just kind of auto-installs and says it is done, but plugging the phone in after that doesn't present an HTC Diagnostic port in device manager. No devices with a bang next to it, everything is installed.
Dialing ##3424 just gives me a "Your # cannot be dialed at this time..." message. I'm running the 6.5 21501 build right now.
Click to expand...
Click to collapse
Hey,
Did you try "##3424#" ? On my Qwest Moguls, That is what works. Also, did you install your carrier cab file? Sometimes I need to run the program from the exe file in the windows folder.
Yeah the carrier works, everything on the phone does except sat lock takes forever the first time like it did before my initial QPST modification so I'd like to redo it. I'll try ##3424#. Thank you.
Not all dialers in custom roms support ## codes. So you might have one of the bad dialers. Ask the rom cook or find a new dialer.
I'm using the Telus IP on Verizon and it seems to be working fine.
Panth said:
Looking through all the posts in the forum, I can't seem to find a recent conclusion on PDE information for Verizon. Thus, consolidation time!
If you have your aGPS working well for a custom ROM (ie DCD 3.2.3 and radio 3.42.50) on Verizon, what are the aGPS registry settings and QPST settings you're using?
Click to expand...
Click to collapse
I'm using the 6.5 rom from BBSandKM, version 21728. I have been using some of the 6.5 roms from earlier builds as well.
In QPST my settings are:
PDE IP ADDRESS: 66.174.95.132
PDE Port Number: 8888
PDE Transport: IP
Position Calculation: mobile
I use the same IP address & Port # in Reg. Settings. I set GPS Mode to 2.
I have no problems getting locks in under 30 seconds. Sometimes in less than 10 seconds.
Good luck.
JimmyGene said:
I have no problems getting locks in under 30 seconds. Sometimes in less than 10 seconds.
Click to expand...
Click to collapse
Same here. Only I'm using GPS Mode=4. I've also noticed that if the QPST settings are good you dont need to do anything in the registry (unless you have to fix or delete bogus settings). A vanilla ROM like tplane37's 21501 + QPST works right out of the box.
I resorted to opening dmrouter /diag since ##3424 wouldn't work.
scorp508 said:
I resorted to opening dmrouter /diag since ##3424 wouldn't work.
Click to expand...
Click to collapse
Did you try ##3424#? That worked for me.
Hi everyone, PLEASE READ PLEASE READ STEP BY STEP i was reading and a lot of people have questions about going to metropcs and nobody give them really good help, so i decided to make this post for you guys but please please do not post me asking how to do it in other htcs phone or worst in samsungs, lgs, etc etc I AM DOING IT THIS ONLY FOR HTC RAPHAEL or 6850 or touch pro cdma what ever you want to call it. ok so lets get start it. you have either two options:
1. Install the Hard-SPL (to unlock the phone), Install custom radio, Install custom rom, Install and modify files to make it work in Metropcs internet,mms etc. and finally take it to metropcs pay between $40 to $60 box so they flash it and you have already the phone working with everything. (recommened for dummies)
2. Install the Hard-SPL (to unlock the phone),Install custom radio Install custom rom, Install and modify files to make it work in Metropcs internet,mms etc. and Flash the HTC 6850 Touch Pro MEID and ESN to Clone the phone (i assume you have one phone already working on metropcs and you dont want to use the phone anymore so you clone it hehehehe.
--------------------------------------------------------------------------
1.Option. Download this file first:
http://www.4shared.com/file/140639926/7fa190d6/TP_ESN_FILES2.html
Important:
first, if you have GSM Touch Pro/Raphael (NOT CDMA, NOT SPRINT/VERIZON/ALLTEL/TELUS/BELL), this will brick your device.
to download a compatible hardspl package for gsm touch pro you can go to forum.xda-developers.com.
but if you have CDMA Touch Pro/Raphael, then you have to use this hardspl, not the one at xda-developers!!!
preparations before flash:
1) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
2) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
3) now decide which Hard-SPL you want to flash. if you have Verizon, flash VZW package (from verizon attachment). if you have Sprint, Telus or Alltel or Bell, flash default package (Raphael_CDMA_HSPL_037.zip).
instructions:
1) extract Hard-SPL Raphael_CDMA_HSPL_037.zip
2) you must Have Phone Synced with PC in Windows Mobile!
3) run HardSPL exe that you extracted before.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) it should go to tricolour screen now and say 0.37.C-SSPL or for Verizon devices it should say 0.35-C-SSPL.
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.37.CMONEX MFG.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the SSPLManual.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
make sure to get SSPL-Manual specifically for Verizon phones from the verizon package.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here.
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL.
NOTE 5: use Relocker *only* if you need to return the phone for warranty. only use it as last step - after reflashing stock OS and radio. Default relocker is for Sprint etc, Raphael_CDMA_VZW_Relocker in the verizon package is for Verizon touch pro's.
(Please Donate to the CDMA Raphael Project Team - http://shorl.com/frastijeketrebo - Thanks!! )/ source
Next.Next.
we need to install the Radio, (make sure the phone is recognized by microsoft sync) i relized that the better one out there for metropcs is Telus v1.04.05V thats why i put it in my rar file.
1. extract Telus v1.04.05V and run ROMUpdateUtility
2. install it
3. when is done make sure the radio is v1.04.05V (in the dilaler press menu then press phone information and look for Radio.)
Next.
Install the rom of your chooise.I recommend for metropcs either mightyrom
(http://forum.ppcgeeks.com/showthread.php?t=52695) or NFSFAN's Custom WM6.5 ROMs (http://forum.xda-developers.com/showthread.php?t=516509) a lot of people ask for a custom rom for metropcs and thats not necesary to have almost every raphael cdma rom out there is compatible with metropcs.
-Elite Rom RC1 choose telus
http://forum.ppcgeeks.com/showthread.php?t=72401
-NFSFAN's Custom WM6.5 ROMs.
http://forum.xda-developers.com/showthread.php?t=516509
-www.MightyROM.com
http://forum.ppcgeeks.com/showthread.php?t=52695
-HAZE V1.6 Native 6.5 Kernel.
http://forum.xda-developers.com/showthread.php?t=561931
-Reflectionist Rom V0.6
http://forum.xda-developers.com/showthread.php?t=562337
-Black Dragon Titanium Rom 23420
http://forum.xda-developers.com/showthread.php?t=547846
-alpha build 1.5
http://forum.xda-developers.com/showthread.php?t=559640
-JUICY 8
http://forum.xda-developers.com/showthread.php?t=518466
-WM 6.5 21501 djbeames
http://forum.xda-developers.com/showthread.php?t=509544
-grooveROM 5
http://forum.xda-developers.com/showthread.php?t=534888
-EnergyROM 'Photon'
http://forum.ppcgeeks.com/showthread.php?t=69545
-Calkulin's Visual
http://forum.ppcgeeks.com/showthread.php?t=87040
-MurdaROM
http://forum.ppcgeeks.com/showthread.php?t=87040
-SsS-ROMv0402
http://forum.ppcgeeks.com/showthread.php?t=68755
-NK-All Carriers-RZ Baseline 3.2
http://forum.ppcgeeks.com/showthread.php?t=81038
-Demolition 6.5
http://forum.ppcgeeks.com/showthread.php?t=66799
-Psyki 4
http://forum.ppcgeeks.com/showthread.php?t=66993
-JD's Clean
http://forum.ppcgeeks.com/showthread.php?t=73860
-Sac ROM
http://forum.ppcgeeks.com/showthread.php?t=68734
-SilenceROM
http://forum.ppcgeeks.com/showthread.php?t=84859
-eRice
http://forum.ppcgeeks.com/showthread.php?t=46965
-MERDIN'S WMPro
http://forum.ppcgeeks.com/showthread.php?t=50716
-StarROM 2.0
http://forum.ppcgeeks.com/forumdisplay.php?f=68&order=desc&page=2
-TruXt v5.1
http://forum.ppcgeeks.com/showthread.php?t=82653
-Chaos ROM
http://forum.ppcgeeks.com/showthread.php?t=75974
-Longhorn ROM
http://forum.ppcgeeks.com/showthread.php?t=65849
-Sceptre Rom 3.4 SenseSuite
http://forum.ppcgeeks.com/showthread.php?t=75215
-dcd's hermann ROM 2.00
http://forum.ppcgeeks.com/showthread.php?t=69754
-091409 XOR
http://forum.ppcgeeks.com/showthread.php?t=84394
-CFAY 1.5.5
http://forum.ppcgeeks.com/showthread.php?t=50471
-Juggalo TP ROM v0.08B (choose telus)
http://forum.ppcgeeks.com/showthread.php?t=49341
-JonRom Version 2.55
http://forum.ppcgeeks.com/showthread.php?t=79924
-FuzeBerry II
http://forum.ppcgeeks.com/showthread.php?t=62786
-midNIGHT v5.5
http://forum.ppcgeeks.com/showthread.php?t=75032
-Copper v.0.0.0.1
http://forum.ppcgeeks.com/showthread.php?t=64242
-Ivan's ROM 1.9.S.V
http://forum.ppcgeeks.com/showthread.php?t=48463
-dB_ROM WM 6.5
http://forum.ppcgeeks.com/showthread.php?t=67426
-FALLEN ROM
http://forum.ppcgeeks.com/showthread.php?t=63479
-Yay 4 Juggs
http://forum.ppcgeeks.com/showthread.php?t=61274
-Jmz Rom 3.0
http://forum.ppcgeeks.com/showthread.php?t=61953
-FireROM
http://forum.ppcgeeks.com/showthread.php?t=73395
-KK's Loaded ROM v1.8
http://forum.ppcgeeks.com/showthread.php?t=52307
-Tech1 MultiMedia
http://forum.ppcgeeks.com/showthread.php?t=72782
-JOKER ROM
http://forum.ppcgeeks.com/showthread.php?t=68213
-DREAM Full and Lite
http://forum.ppcgeeks.com/showthread.php?t=49338
-THE LAST-Forgiven
http://forum.ppcgeeks.com/showthread.php?t=70059
-NSFW College ROM
http://forum.ppcgeeks.com/showthread.php?t=69371
-PhantomROM
http://forum.ppcgeeks.com/showthread.php?t=62796
-JowPod
http://forum.ppcgeeks.com/showthread.php?t=69269
-Merdin's
http://forum.ppcgeeks.com/showthread.php?t=59780
-PsykiROM v1.0
http://forum.ppcgeeks.com/showthread.php?t=65145
-nueROM-S
http://forum.ppcgeeks.com/showthread.php?t=42777
i think thats it if you know another one just let me know i will post it.
Finally the most difficult part in this process.
set up the internet, mms and GPS
download this file:
http://www.4shared.com/file/140658132/5838a6f3/MetroPCS.html
-connect your phone to de pc and install get spc in the phone
-run it and press on get spc, press ok or yes and it will display six digit number write this number down because we will need it.
-in the dialer type ##778# click on edit and write the six digit number that you wrote down.
-next a screen that says EPST and below that say Display will appear.
-we well need to modify some of this ones
DISPLAY
-NAM NAME write you ten digit numer
-SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that)
-MSID write your ten digit phone number
click in view info and go to
NAM SETTINGS
-NAM NAME write your ten digit phone number
-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516
-MIN2 first three digits of your phone number (area code)
-MSID write your ten digit phone number
-MCC 310
-MNC 27
-NMSI 27and write your ten digit phone number
-IMSI 31027and write your ten digit phone number
Part 2
click in view info and go to
CDMA SETTINGS
-A-SYS PRIMARY 283
-B-SYS-PRIMARY 384
-A SYS-SECUNDARY 691
-A SYS-SECUNDARY 777
-MON_TERM_FOR_HOME ENABLE
-MON_TERM_FOR_SID ENABLE
-MON_TERM_FOR_NID ENABLE
-EVRC ENABLED DISABLED
-HOME PAGE VOICE 13K
-HOME ORIG VOICE 13K
-ROAM ORIG VOICE 13K
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535
click in view info and go to
MODEM SETTINGS
-SLOT CYCLE 1
-PREFERRED SERVING AUTO
-PREFERRED MODE AUTO
-HDR HYBRID ENABLE
-CLEAR ALL MRU NO
click in view info and go to
-PRL
-UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE
click in view info and go to
SECURITY
-HDR AN AUTH USER ID [email protected]
-HDR AN AUTH PASS metropcs
-PPP USER ID [email protected]
-PPP PASS metropcs
click in view info and go to
DATA PARAMETERS
-PACKET DIAL #777
click in view info and go to
M.IP SETTINGS
-NUMBER OF PROFILES 6
-ACTIVE USER PROFILE 0
-MIP_MODE SIMPLE IP ONLY
-MIP REGISTRATION RETRIES 1
-MIP REGISTRATION RETRY 2000 ms
-MIP PRE-REGISTRATION TI 30
-MOBILE NODE-HA Disable
-SEND A REGISTRATION Enable
-DORMAND HANDOFF Disable
click in view info and go to
M.IP DEFAULT PROFILE
-ENABLE PROFILE Enable
-NAI [email protected]
-MN HA SPI SET Disable
-MN HA SPI VALUE 0
-MN AAA SPI SET Disable
-MN AAA SPI VALUE 0
-HOME ADRESS 0.0.0.0
-PRIMARY HA ADDRESS 255.255.255.255
-SECUNDARY HA ADDRESS 255.255.255.255
-HA SHARED SECRET metropcs
-AAA SHARED SECRET metropcs
-DMU 0
-MN 0
make sure that
M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable
click menu ok and reset.
when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROPCS.CAB
also after everything is done please dont forget to take the phone to metropcs so they can put you nam in the metropcs system thats what they call flash the phone to metropc.
Internet Sharing - tethering big thanks to silvaadams from ppcgeeks
make sure you have internet on your phone ofcourse
start up comm manager and click your internet sharing button thingy lol
click connect on the lower left hand corner
wait for phone to say check usb connection
then connect phone to usb and usb to computer (should say connected)
open internet explorer
go to settungs
go to internet options
go to connections tab
click on lan settings
click proxy server check use proxy blabla
then type wap.metropcs.net port 3128
then ok
open up firefox
once open go to tools> options> advanced> network
under network click settings
select manual proxy config
under http proxy type
wap.metropcs.net [port:] 3128
then check off "use this proxy server for all protocols"
--------------------------------------------------------------------------------------------------------------------------------------------
2.option. HTC 6850 Touch Pro change MEID change ESN Repair / Clone Solution i assume you have a phone already in metropcs so u can clone it and avoide paying $40 or $50 dollars activation fee.
Download this file first:
http://www.4shared.com/file/140639926/7fa190d6/TP_ESN_FILES2.html
PLEASE READ SOME DIFFERENCES FROM OPTION 1.
Important:
first, if you have GSM Touch Pro/Raphael (NOT CDMA, NOT SPRINT/VERIZON/ALLTEL/TELUS/BELL), this will brick your device.
to download a compatible hardspl package for gsm touch pro you can go to forum.xda-developers.com.
but if you have CDMA Touch Pro/Raphael, then you have to use this hardspl, not the one at xda-developers!!!
preparations before flash:
1) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
2) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
3) now decide which Hard-SPL you want to flash. if you have Verizon, flash VZW package (from verizon attachment). if you have Sprint, Telus or Alltel or Bell, flash default package (Raphael_CDMA_HSPL_025_MFG).
instructions:
1) extract Hard-SPL Raphael_CDMA_HSPL_025_MFG
2) you must Have Phone Synced with PC in Windows Mobile!
3) run HardSPL exe that you extracted before.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) it should go to tricolour screen now and say 0.25.C-SSPL or for Verizon devices it should say 0.35-C-SSPL.
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.25.CMONEX MFG.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the SSPLManual.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
make sure to get SSPL-Manual specifically for Verizon phones from the verizon package.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here.
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL.
NOTE 5: use Relocker *only* if you need to return the phone for warranty. only use it as last step - after reflashing stock OS and radio. Default relocker is for Sprint etc, Raphael_CDMA_VZW_Relocker in the verizon package is for Verizon touch pro's.
(Please Donate to the CDMA Raphael Project Team - http://shorl.com/frastijeketrebo - Thanks!! )/ source
-install the radio that is on TP ESN FILES2\RAPHING
-install the rom of your choise from Option 1
-now MAKE SURE YOU WRITE DOWN OR BACK UP ALL YOUR DATA SETTINGS BEFORE YOU DO THIS JUST IN CASE
- download
http://www.4shared.com/file/140658132/5838a6f3/MetroPCS.html
- install WModem_Driver_Installer_v1.2.2.4_WWE
-make sure to install get spc on the phone run it and get ur spc code
-disconnect phone
-put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc
-now install all the drivers but maybe it will tell that u need qcmdmxp or another one so just select files from Program Files\HTC\WModem_Installer\WinXp
-Disable USB connection in Active Sync by unchecking checkbox in Connection Settings of Active Sync
-Hold Pwr and Vol Down buttons and push reset button to boot the phone in bootloader mode.
Part 3
-Run mtty.exe from TP ESN FILES2
-Leave every setting alone apart from change the 'Port' to 'USB' in yhe drop down box. Hit OK.
In the window that opens up, type the following commands (All Commands are case Sensitive) Hit enter after typing each one. You may see nothing while typing, just type carefully.
1. rtask a
12 echo_on
3. readCID
4. writeCID 00000000
5. readCID (window should return CID as 00000000)
6. rtask c (will probably give and error - mine did!)
-Soft reset phone and close mtty.
-Re-enable USB connection in connection settings of ActiveSync. Make sure phone is 'connected' to ActiveSync, you might have to unplug and plug in usb to make this happen.
-Flash phone with Raphael_CDMA_HSPL_037.exe
-Let phone restart.
-disconnect phone
-put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc
-download http://rapidshare.com/files/210789608/QPST_2.7.323__2008-09-19_.rar
-open QPST configuration and click on add port
-make sure to memorize the port that says htc diagnostic that port com is really important we well use it for many things
-Launch DFS. from TP ESN FILES2
-Select your phone's com port. (top left ish) this is the port that i was talking about diagnostic port com
-Select 6950 from the HTC devices menu on the left. Before you all start, yes I know we are programming a 6850, but the secret here is that the MEID portion of the 6850 equipment file in DFS ties up to the MEID locations in the radio rom supplied (which was ported from the diamond)
-Ignore any errors at the bottom of the screen about equipment not found etc... Remember, just follow the instructions!! So, once the com port is connected, go the MEID section and type your originial metropcs phone the one you have to clone MEID(D)(decimal) it should be on the back of the phone also make sure that the original metropcs phone os turn off u dont want to turn this phone ever in your life. Ignore the pESN that it creates but do not modify it
-Click Write like 4 times and it will write it to the phone no matter what it says at the bottom of the screen.
-Close DFS and soft reset.
-now go to http://www.previo.net/meid-esn-converter.html
-type your MEID(D)(decimal) and click submit the important thing here is ESN the hex not the dec. so copy the hex one.
-Go into diag mode ##3424# again wait untill the white screen disappear and connect it usb to ur pc
-Open up the attached CDMA Workshop 2.7 cdma workshop.exe but the one is in METROPCS.RAR not the one is in TP ESN FILES2 and select the com port to connect your phone. THIS COM PORT IS THE DIAGNOSTIC PORT.
-click connect and then read
-in your phone go to dialer and type ##778# edit and type your spc code then.
-Go to the security tab in workshop and click read by the esn. It should display your current esn.
-Type the esn that the website give you the hex one. this should be your original metropcs nam number
-click write.
-Go to Nam tap and Click in Banner
-Type MetroPCS and
-click write
-now Close CDMA WS and soft reset
-now install the radio u want to use from here
http://forum.xda-developers.com/showthread.php?t=531134&highlight=radio
recommend TELUS v1.04.05V or VERIZON v1.03.03V
-when is done type in your dialer ##778# edit in the screen that says EPST and below that say Display will appear.
-we well need to modify some of this ones
DISPLAY
-NAM NAME write you ten digit numer
-SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that)
-MSID write your ten digit phone number
click in view info and go to
NAM SETTINGS
-NAM NAME write your ten digit phone number
-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516
-MIN2 first three digits of your phone number (area code)
-MSID write your ten digit phone number
-MCC 310
-MNC 27
-NMSI 27and write your ten digit phone number
-IMSI 31027and write your ten digit phone number
click in view info and go to
CDMA SETTINGS
-A-SYS PRIMARY 283
-B-SYS-PRIMARY 384
-A SYS-SECUNDARY 691
-A SYS-SECUNDARY 777
-MON_TERM_FOR_HOME ENABLE
-MON_TERM_FOR_SID ENABLE
-MON_TERM_FOR_NID ENABLE
-EVRC ENABLED DISABLED
-HOME PAGE VOICE 13K
-HOME ORIG VOICE 13K
-ROAM ORIG VOICE 13K
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535
click in view info and go to
MODEM SETTINGS
-SLOT CYCLE 1
-PREFERRED SERVING AUTO
-PREFERRED MODE AUTO
-HDR HYBRID ENABLE
-CLEAR ALL MRU NO
click in view info and go to
-PRL
-UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE
click in view info and go to
SECURITY
-HDR AN AUTH USER ID [email protected]
-HDR AN AUTH PASS metropcs
-PPP USER ID [email protected]
-PPP PASS metropcs
click in view info and go to
DATA PARAMETERS
-PACKET DIAL #777
click in view info and go to
M.IP SETTINGS
-NUMBER OF PROFILES 6
-ACTIVE USER PROFILE 0
-MIP_MODE SIMPLE IP ONLY
-MIP REGISTRATION RETRIES 1
-MIP REGISTRATION RETRY 2000 ms
-MIP PRE-REGISTRATION TI 30
-MOBILE NODE-HA Disable
-SEND A REGISTRATION Enable
-DORMAND HANDOFF Disable
click in view info and go to
M.IP DEFAULT PROFILE
-ENABLE PROFILE Enable
-NAI [email protected]
-MN HA SPI SET Disable
-MN HA SPI VALUE 0
-MN AAA SPI SET Disable
-MN AAA SPI VALUE 0
-HOME ADRESS 0.0.0.0
-PRIMARY HA ADDRESS 255.255.255.255
-SECUNDARY HA ADDRESS 255.255.255.255
-HA SHARED SECRET metropcs
-AAA SHARED SECRET metropcs
-DMU 0
-MN 0
make sure that
M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable
click menu ok and reset.
when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROPCS.CAB
reset it one more time
finally call *228 wait untill the spanish thing is over and press 1 then wait 2 seconds press 1 again wait 2 seconds and press 1 again this will make u talk to custumer service tell them u are having trubles with ur phone and you need to reprogram your phone sometimes they are lazys and dont want to do it so insinst. please give them your MEID(D) decimal number and depend of your phone they will tell you do this or do that but dont do it write everything down and tell them yes ok i done hahaha in my case of kyocera melo they told me to do this type 111111 go to options service go to program 587846 type mdn MYPHONENUMBER type min 3234764516 and type home sid 6503 after that they told me im done just soft reset it and that its but when i hang up i didn do it and please dont do it go to dialer and type ##778# edit and we need to make some changes.
DISPLAY
-NAM NAME write the program number they give u my case 587846
-SCM write 58
click in view info and go to
NAM SETTINGS
-NAM NAME write the program number they give u my case 587846-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516 type the min number they give in my case 3234764516 323 is the area code but when u restar the phone this dissapear
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535 here just change the the SID for the one they give you my case 6503 the other one leave it as 65535
soft reset and you are ready to go.
Internet Sharing - tethering big thanks to silvaadams from ppcgeeks
make sure you have internet on your phone ofcourse
start up comm manager and click your internet sharing button thingy lol
click connect on the lower left hand corner
wait for phone to say check usb connection
then connect phone to usb and usb to computer (should say connected)
open internet explorer
go to settungs
go to internet options
go to connections tab
click on lan settings
click proxy server check use proxy blabla
then type wap.metropcs.net port 3128
then ok
open up firefox
once open go to tools> options> advanced> network
under network click settings
select manual proxy config
under http proxy type
wap.metropcs.net [port:] 3128
then check off "use this proxy server for all protocols"
thanks to englishdan from mobile-files.com, xda forum, cmonex, and everybody that makes this possible. also i download the files and i forgot most of the post that i got the files so please all the people that makes this files and aport to this excuse me for that my apologize i just want to make this easier to everybody becasue i spend days and days trying to do this thanks to the users from PPCGeeks, howardforums, and mobile-files. without this it wouldnt be possible to make this also my apologize if there is things from other forums not mentioned but i forgot most of the places and users that take infotmation off once again thank u.
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
hey bro
dude i work my ass off to get this work for 7 days sleeping only 3 or 4 hours i put all this info togheter four you guys and then u re telling me this, no where u will find this and i post at the last thanks to the guy who help me the most but if you go to his profile and see the post http://www.mobile-files.com/forum/showthread.php?t=111584 u will see how empty is a lor of questions and a lot of people that are confused but if you look what i write is so complete that everybody will understand there is a lot of people that i have to thanks but if i write all the names down there will be no space in the forum read bro and i thanks to all of them i mention at the end so please shut the **** off because i work my ass off to make this post.
snail813 said:
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
Click to expand...
Click to collapse
Great Job Looser
First post...yeah! Something tells me you're like one of those off duty english teachers: cite your sources.... Suck a fat one. Drey did an excellent job trying to help others and not himself. He doesn't even have a paypal link on the bottom of the posting. I have my TouchPro on metropcs fully functioning from multiple links on ppcgeeks and xda-developers. Thanks to many.
Drey, You did great with this post man! Too bad an off duty buttwhole is around fouling things up! What a jerk off. First post! lol.
snail813 said:
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
Click to expand...
Click to collapse
Metro WAP
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
belalucf said:
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
Click to expand...
Click to collapse
If you had the phone flashed to metropcs all you have to do is input the Metro WAP settings. I did not use a cab file. First HardSPL, Archsoft MMS, then change WAP settings, and the registry.
wap
Yeah I tried inputting all the settings, then creating a new connection called metro pcs with all the port settings and stuff, which I don't even see on this guide. Because if you don't create a new connection, it wont do anything once I removed the sprint connection which I did by changing the guardian file, which allowed me to even remove it. But I was hoping that this program would I guess populate that stuff somehow, so I went through and manually put in all those settings. Still no connection
ok
ok you can do it this way put your phone in dial mode ##3424# wait until white screen turns off and open workshop 2.7 from mteropcs.rar you have to go other tab under PRL choose write and select the ppl file
when you open the browser a window will apear you have to write your [email protected] and metropcs as password
note u set this up ##778# edit Mip default profile thank u
belalucf said:
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
Click to expand...
Click to collapse
thanks bro
thanks bro for me was hard i have to go to so many forums and read and read to make this work for my little brother, i gave him this phone as a gift but in sprint and he have metropcs so i decided to read and find out how this works and after work my ass off for 1 week taking information from here there ask so many questions i decided to make all that info in one post and then this jerk tell me this bro i am doing this to help everybody the important thing here is share so other people can learn and not like me that spend hours in my pc trying to figure this out thanks bro..
stukes said:
First post...yeah! Something tells me you're like one of those off duty english teachers: cite your sources.... Suck a fat one. Drey did an excellent job trying to help others and not himself. He doesn't even have a paypal link on the bottom of the posting. I have my TouchPro on metropcs fully functioning from multiple links on ppcgeeks and xda-developers. Thanks to many.
Drey, You did great with this post man! Too bad an off duty buttwhole is around fouling things up! What a jerk off. First post! lol.
Click to expand...
Click to collapse
mmm
if the cab file that i gave u (THANKS TO RYANMONGUL6800)didnt work try to do it manually http://rferreira1.googlepages.com/revisedMogul6800tometro.pdf if stills not working try to start again first install the cab file then go to ##778# edit ur spc code then edit mip. default profile for the one i have soft reset open browser it should ask for the username [email protected] and pass metropcs if still not owrking u have to follow this
from ryanmongul6800
Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the password below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
Click view info and pick MIP Default Profile, Enable profile should be ENABLE, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 255.255.255.255, secondary should be 255.255.255.255, HA shared secret and AAA secret should be metropcs <--lowercase, DMU public should be 0, MN Authenticator should be 0.
Click view info and pick MIP customer profile 1 and make sure Enable profile is DISABLED. Now do the same with the other 4 profiles (profiles 2-5), make sure that the only profile enabled is MIP Default Profile.
Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778 call button (PST/EPST), we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to [email protected], password should be metropcs<--lower case, same for PPP user id and Password make them same as HDR.
Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both metropcs<---lowercase, then click menu OK and let it reset.
belalucf said:
Yeah I tried inputting all the settings, then creating a new connection called metro pcs with all the port settings and stuff, which I don't even see on this guide. Because if you don't create a new connection, it wont do anything once I removed the sprint connection which I did by changing the guardian file, which allowed me to even remove it. But I was hoping that this program would I guess populate that stuff somehow, so I went through and manually put in all those settings. Still no connection
Click to expand...
Click to collapse
Wap
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
hard way
ok you can try this out i have not try it so i dont know if it would work first go to control panel, then system hardware, device manager click universal serial bus controllers and unistall all of them restart your pc and it would install back the usb drivers then connect the phone diag mode if doesnt ask for drivers go to control panel, then system hardware, device manager go to ports( com & lpt) you should see htc diagnostic port if the port is below 27 we are fine if not delete all of them but do not unistall com 1. dont worry it will delete ports that u install thins when u plug things u have to install again so don worry. now if the phone ask you for drivers once u delete everything install them again but this time if still port higher than 27 go to device manager click in com 1 click update drivere install from specific locatiuon, dont search i will install have disk browse go to programs files /WModem_Installer/qcusbmdm.inf next yes ok and thats it you have it in com 1 after u done everything just delete port com 1 and it will install it after u reset the computer thank u..
u need to install WModem_Driver_Installer_v1.2.2
from metropcs.rar
try it in your friends computer or some internet cafe pcs hehehe i know bro always something happens
belalucf said:
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
Click to expand...
Click to collapse
if that doesnt work
i pretty sure it will work but just in case the methods dont work try to borrow a pc from ur friend or go to an internet cafe hehehehe
belalucf said:
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
Click to expand...
Click to collapse
thanx for all the help i had wap and mms working but internet sharing and gps didnt thanx again
GPS
cdw9800 said:
thanx for all the help i had wap and mms working but internet sharing and gps didnt thanx again
Click to expand...
Click to collapse
Do you have quickGPS installed??? This it is available on the forums and wiki just do a search. It downloads updated satellites for google and other apps to use.
metro pcs
Well i got cdma to see the htc, but when i open the browser it says provisioning data services and says it can't connect.
check
ok just please more specific which rom are you using and the steps u did
belalucf said:
Well i got cdma to see the htc, but when i open the browser it says provisioning data services and says it can't connect.
Click to expand...
Click to collapse
Awesome
I wanted to change carriers from Cricket to MetroPCS. Metro told me I would have to go to Dallas to have the Metro flash applied. Well that is a 2+ hour drive from where i am. I like Metros pricing plan. I can have 3 phones for the same amount I pay for 2 Cricket. Good job on this write up and work you have done.