Hi everybody
I have a big problem:
when i lost the gsm signal the phone is power off and never recive incoming calls ... until i'll power on again.
Is there some settings in order to search the gsm signal always...?
...cause i can't control the xda every 5 minutes if have signal or not...
I have 4.21 radio and 4.00.11 rom
Thanks all
Denis
have you tried a hard reset? or even re-writtin the bios?
that worked for me
Hi Guys,
I need your help .
I've downloaded the 4.00.16 ROM by mistake, it really didn't tell the ROM number, so now I want to revert to a earlier one and I can't.
I've got the following message: "ERROR: GetDeviceData - An established connection was aborted by the software in your host machine.
error getting devicedata" and then "ERROR 011: EXECUTE REMOTE COMMUNICATION PROGRAM ERROR. Cannot execute the remote communication program. Please make sure that the USB/Serial cable is properly connected."
PLEASE HELP ME, I'M REALLY STUCK NOW AND DON'T KNOW WHAT TO DO...
Sorry ... when can i get the radio 6.24.00 ???
can work for Italy ?
What do you mean with "re-writtin the bios" ... ? the SD card boot ?
Thanks
Related
I try a lot of things, but, ....still no gsm
details:
first, all instalation (os, ext , radio) finished succesfull, but after reset I don't have any phone...
I try again, and the installer stop at radio (installing only the os and ext.)with message : press reset +power+directional... ant try again.... I try again but still same message apear
If anybody can help me please, reply!!!
try the other thing, the one you haven't tried.
A bit hard to help with so little detail.
Which OS,Radio original ?
Which OS version? which Radio version?
how do you mean "no GSM"? no signal? no phoneProgram?
what have you tried?
no gsm at booting
no radio, protocol and imei in device information
I make a BIG mistake, I dont make a beckup
original:; Os : 1.72, Radio version 1.16 (I think)
Now : os 2.06.00 wwe , Radio no specs.
I have the phone program , but I can't communicate to SIM (no aplication installed, if i try to run Sim toolkit),
antena icon with "!" say "No service"
when I press the phine button, the program start but with large delay.
have you double check your language and operator for nk.nbf; ms_.nbf; and radio_.nbf with xda2nbftool.exe???
Resurrect
Flash it with the launch ROM.
I just update..... don't make any verification and now i'm very sad...
[Krueger]Dr.Stein - I don't understend!
Huh?
othgor said:
I just update..... don't make any verification and now i'm very sad...
[Krueger]Dr.Stein - I don't understend!
Click to expand...
Click to collapse
What did you do?
I think he only did the upgrade with a nk.nbf and ms_.nbf.
Frpm the messages I think he means the device says it doenst have the GSM functionality operational. Typically the result of upgrading without Radio.nbf
Get a good (1.17 / 1.18) Radio.nbf (set operator!!!) & try again
i have same problem where is launch version
ok i got xda2 02 launch rom
which unable to communicate
while xda2s can upgarde my rom but error 114 no gsm
i also got launch rom but it cant communicates
I have same issue.
I upgraded a TMobile XDA1 got the main ROM upgrade then went and tried to upgrade the radio stack. As I see from the many posts a bad thing to do. But this leaves me with a broken unit. The radio was T310. I can not see how I can solve this problem. I have an SD card, I have a friends German unit with an ENG Rom and the orignal radio which I will leave alone. How can I fix mine?
Thanks
GSM error on Bootload 1.50
Looks pretty much the same as my problem. By pressing the joystick after the error message, I get one step further, but no contact or upload of the ROM. I hope some wise person can supply an answer, :roll:
I have the same problem...
XDA O2 on Wallaby BootLoader v5.15 I see the error : "GSM ERROR"
my pda don´t start good I only see the rom version (3.17.03) and a blue wallpaper of O2..
I already update my rom but it don´t work yet !
Where can I find a GSM rom update? I'm from Portugal
What more can I do ?
Please, help me !
thanks
Joao Afonso, from Portugal
GSM Error
I have tried a number of solutions. None seem to work. If someone has the GSM rom and a solution to upload it let us know. I have tried coping a new radio version to the windows dir on the PPC, this fails. I have removed the back cover and battery again this does not work. The only alternative is to send it back for repair (expensive) or get a new one. I have looked at the solutions in the forum area and on the web but can not find an answer. The unit is an old TMobile (GERMAN) Xda. Upgraded the OS OK then messed up the radio. So as I say let me know if someone has a proven solution. Thanks.
How to fix GSM Error Problem ....
Download the XDA-Developers ROM Version 1.1.
Install the ROM on your Device via SD-Card and bootloader.
The phone should start up and give you the screen allignment and the whole menu!
Download an Upgrade for your device. This depends ont the model you are using. Check the sticker at the back of your device.
If it is a PW10A-Model download RSU Version 4.16.
If it is a PW10B-Model download RSU Version 6.24.20.
Extract the downloaded ZIP-File and copy all files to the /Windows directory of your device.
Copy the RSUpgrade.exe additional to the /windows/startup directory.
Make an soft reset of your device.
Maybe the upgrade will stop again at 1%, this may occur when you have an empty battery.
Place your device in the cradle. Run Active Sync on your device.
The RSU Upgrade will run in the background.
Wait for about 10 Minutes. The upgrade should complete in the background....
Afterwards all should work again...
Good luck....
Click to expand...
Click to collapse
GSM Error
Many thanks for the information. I have tried this but to sorry to say this does not work for me. I can get the RSUgrade.exe to load on the PDA, it stops at 1% and then hangs. The XDA was a TMobile GER unit with 32Mb. I have two units the same, I attempted to upgrade the radio on one and it failed at 10% rebooted and hung with GSM error. Since then I am at a loss as to the next step apart from throwing it in the bin.
same here
it always promt me failed flash device restart press ok. wat the hell is dis . does my gsm rom id basted?day i cant upgrde it tnx
Same problem..
.. and no solution for the GSM Error. There is no possibility to get a connect (O2 germany) and the RSU-Utility stops after 1% - always.
Please help!
Have you tried leaving it for 24 hours with the 1% on screen?
Flash failed
The problem is that there is a message "Flash failed - press ok to restart."
No possibility to leave the program..
same w u
ya i wish someone can find any sol 4 our prob. same problem w u guys.
Dear friends
I was tring to upgrade my iMate Pocket PC also know as Himalaya with windows2003 SE , while upgrading I faced problems, the upgarde failed and now I am just getting no display and OS too. The only message displayed is
Serial
v1.03
nothing is working please help
bye with regrads,
your unit is still okay; even better that the usb version is showing on the screen. it's simply stuck on bootloader mode. what kind of problems did you encounter resulting in the failed upgrade?
one suggestion i can give before you downgrade is to try and proceed with the upgrade to se. put your unit back on the cradle but don't expect activesync to "recognize" the device. just put it back on the cradle and rerun the upgrade to se.
same thing happened when i upgraded but to wm2005. the screen showed error and the only thing on the screen was the usb version. i simply cradled back the unit and ran the upgrade. worked.
cheers
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
oh, it appears that you have the "wrong country" id issue. i'm not entirely sure as to how to avoid this but i believe it has something to do with the correct rom version (guys, correct me if i'm wrong). where did you get the rom you used for upgrading to se? downgrading might be the only trick if there is no rom for saudi-based users...but if any chaps presently living there and were successful in upgrading their units perhaps you could share the rom version/s you used?
cheers
yasirirfan said:
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
Click to expand...
Click to collapse
To overcome the Country ID Error, first you need to install this tool...
ftp://xda:[email protected]/Tools/ER2003Edit_1_4_26.zip
Open the ROM file you want to upgrade, then change the appropriate 'Operator ID' code, after this click 'Save ROM image'.
Upgrade ur device. You will no longer face the error message.
I have tried many times to upgrade the Rom Image on my HTC Tytn (Cingular 8525) with no success. I am getting a 260 error with the program located at this link...
http://forum.xda-developers.com/showthread.php?t=293665
I did first run the unlocking application to unlock both SIM and CID before running the upgrade.
I followed all the steps exactly and have had no success...
The following might be effecting my attempt:
I am running my pc on Vista
I am syncing with Windows Mobile Device Center
I have tried to solve this problem for about two weeks. Can anyone help me?
Mrvanx has a guide on how to prepare Vista for flashing, you can find it here.
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Same problem
compwiz2008 said:
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Click to expand...
Click to collapse
Same problem here trying to change the radio version after changing the bootloader........
Connection alwayse lost just as said above.
Any help will be appreciuated
justx24
Use the RUU wrapper with the NBH file you want to upgrade.
I still have the same issue, even when using the RUU Wrapper and any nhb.
don't use vista
Ok, got one step furthur
I reached the point where the ROM Begins to update, which is VERY good...
The ROM update Reaches 1%, then waits for 20 minutes...
Then I get a 262 error and have to go through recovery, try again, with the same result.
i have same problem plz help thnx in advance
compwiz2008 said:
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Click to expand...
Click to collapse
Have you tried removing or adding a checkmark to the USB to PC in CONNECTIONS on your device? I remember having a similar problem when I installed Radio Rom 1.38 that my USB connection was lost with the pc . I am using XP when flashing so if you have no luck then do this on a XP machine.
Forgot to ask! What ROM are you trying to flash??
@compwiz2008 and ahmerpar
I read somewhere that running windows update will update WMDC........maybe give that a shot?
Maybe you can try to upgrade your ROM from your SD card.
Nope
Let me try that...
Still did not work
I'm probably going to just take my phone to a computer repair shop and pay them to deal with it, since I'm evedently doing something wrong.
im getting a code 260 and the phone resets it self and active sync looses it connection any ideas
i think u're in the wrong forum..
jstuart83 said:
im getting a code 260 and the phone resets it self and active sync looses it connection any ideas
Click to expand...
Click to collapse
That my friend is a communication error... I had it frequently when trying to install the latest HardSPL under Vista... You can go HERE and see a list of error codes....
ERROR [248~260] : UPDATE ERROR
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
jstuart83 said:
im getting a code 260 and the phone resets it self and active sync looses it connection any ideas
Click to expand...
Click to collapse
AT&T Tilt is a Kaiser....NOT a Hermes.
go to the kaiser forum and they will help you out.
Hermes Getting code 260
I am having the exact same issue. My problem is on a hermes (ATT 8525)
i have the "update error" problem as well. i have read almost all the threads and searched so much i almost found jimmy hoffa, but nothing
i have tried everything i could think of. i reseted the device and computer so many times i think it will "ware out" soon . i tried official roms, hard spl, unlockers... you name it i've tried it and still i cant get past any RUU. after the bootloader it should start, but i doesn't
i've even called the t-mobile tech support but the answer was "our ruu works fine for us, we don't know where the problem is...bad luck"
if some one has any (well don't take this literally) advice he is more than welcome. now i'm gonna chill out
thanx in advance from a frustrated vario II user
i've located the problem. it's an activesync error (code 43). searched for fixes, but unsuccessfully. if anyone has resolved the problem or has relevant info, please post it. thanx
after endles repeats i've somehow managed to get past the error. don't know how. i upgraded the rom smoothly, like i never had any problems