Related
Hi,
I did the popular mistake, tried to unlock with Universal Unlocker , thinking that this is the staff to unlock all the HTC phones.
Ok. What I have now:
NO GSM - we know that
Tried to install radio roms from here, nothing. I got the information about "Checking the information...." and it is hanging like this.
I made reser and HARD RESET aswell.
I tried to install a lot. Nothing helped.
I had radio ver. 1.05.... I remember that. I have my phone from T-Mobile from UK. I had everything nice, now I have four stripes - RED GREEN BLUE and WHITE and ther is written:
HERM300
IPL-1.01
HERM300
SPL-1.04
Can anybody help me ? I tried to download mtty.exe and put all the commands (not PASTE and it still not working.
Now is 6am in Lisbon. I was sitting all that night and I am finishing writting this post.
Help if you can, regards.
Ben
Have a look on this topic http://forum.xda-developers.com/showthread.php?t=280733
It did not help. Where I can get this Qtek rom ? Is that OK for my device ? I have VARIO II from T-Mobile.
I woul like to try instal this - DUMPED English ROM from TMobile Vario II from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_DumpedRoms
but i dont now how. There are 3 .raw files, how to put them to my phone ?
That solution didnt help: http://forum.xda-developers.com/showthread.php?t=280733
What else I can do ? I was trying with QTEK rom and a got white screen on the phone and 0% on the computer. It was hanging. I tried 5 times. Then I tried to install the Radio Rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
I choosed all of them. Nothing. All of them are hanging on:
Chencking the information on your device... Please wait..
Then there is a screen to update. After long time. So when I press the button is still the same info. Checking the information on your device... Please wait..
And its hanging. When I reset to bootloader again the soft telling me:
This ROM Upgrade Utility does not design for your device.
Please get probper ROM Upgrade Utility and try again!
Where can I get the radio version 1.05 for T-Mobile Vario II ???????????
Is there possibility to download from somewhere ?
Or maybe I should try other solution ?
Read "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Yes, I was tying point 5 few times. The problem is, I can connect through mtty.exe without any problems, but after soft reset, I am pressing POWER and OK button and going to bootloader mode again, and when I am trying to flash the extracted radio ROM (i tried all of them = 4) and there is a problem. nothing is working. I am waiting and waiting, and there is only info: Checking your device information or something like that. What can I do ? Sorry for my English guys.
Instead of flashing an extracted radio image try to flash a normal shipped rom (if possible matching your cid). Capture the process using usb monitor to see where exactly it fails and which error you get.
Where can I download
pof said:
normal shipped rom (if possible matching my cid).
Click to expand...
Click to collapse
?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Benone said:
Where can I download ?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Click to expand...
Click to collapse
No rom matching your cid is available then, use the TyTN 1.18 rom.
pof said:
No rom matching your cid is available then, use the TyTN 1.18 rom.
Click to expand...
Click to collapse
I tried that ROM 2 times, once I plugged with holding camera button and second time without. I made monitor of QTEK rom aswell, because its the one which is changing phone screen from red green blue stripes to completly white. But nothing else is doin...
A attaching logs in zip file below. I have 3 files from each session, I dont know which are correct, 2 of them i saved and 1 is exported.
What do you think ?
I used USB-monitor from http://www.hhdsoftware.com/
very weird... usb seems not working but for what you say bootloader seems to be ok. Are you sure this was after patching the radio with universal unlocker? it seems totally a different problem :-$
I guess you'll have to wait until t-mob releases a ROM matching your CID and then flash it using the hermimg.nbh sd-card flashing method.
You can also try to connect to it via serial, I have no experience on that, but a search on these forums might tell you how...
keep us updated
How long I have to wait ?
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Do I really have no chances to repair it by myself ?
Benone said:
How long I have to wait ?
Click to expand...
Click to collapse
Until t-mobile releases a rom with your cid... it can be today or next year, I don't know.
Benone said:
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Click to expand...
Click to collapse
I don't think you lost the warranty. They usually charge about 100 eur for flashing it back in the service centre. They do it by inserting a diagnostics sd card, but we don't have it for the Hermes
Benone said:
Do I really have no chances to repair it by myself ?
Click to expand...
Click to collapse
You can try flashing over serial port, and you can try sd-card flashing, but for sd-card flashing you need a rom matching your CID first.
Eureka!!!
Finally I made my device working again!
And I dont have simlock !
After trying everything.... ufffff.
THX !!!!!!
1) I downloaded ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_Unlock_v1.zip
2) Reset my phone in bootloader mode.
3) Plug USB cable.
4) Run HTC_Hermes_SIM_Unlock_v1.
5) After 20 min. my phone said ELO to meeeee He did not have simlock when was saying that.
YE YE YE
That was simple. If you have any Hermes radio problem, try that first - HTC_Hermes_SIM_Unlock_v1.
Will be more often here, forum seems to be really interesting.
YO!
Yipie
Glad it worked
I know it sounds noob´ish and it surely is, but I just cannot flash anything onto my Hermes right now. I´ve already WM6 and SPL1.13 on it. I also tried SPL1.09ds but all I get from the RUU updater is an Error260 when I try to flash a new WM6 version onto it. I also tried unticking USB connections in ActiveSync and manually starting the bootloader on my Hermes100. Can anybody give me a tip how it can be done?
PS.: Just tried the micro SD card flashing method which used to work here but doesn´t anymore! I´m really stuck now
what is your current SPL/IPL version??
to check press and hold the side ok button and the power button, then insert the stylus into the hole in the bottom of the device.
Hamudi2000 said:
I know it sounds noob´ish and it surely is, but I just cannot flash anything onto my Hermes right now. I´ve already WM6 and SPL1.13 on it. I also tried SPL1.09ds but all I get from the RUU updater is an Error260 when I try to flash a new WM6 version onto it. I also tried unticking USB connections in ActiveSync and manually starting the bootloader on my Hermes100. Can anybody give me a tip how it can be done?
PS.: Just tried the micro SD card flashing method which used to work here but doesn´t anymore! I´m really stuck now
Click to expand...
Click to collapse
For me, I have same experience. I have tried 1.09ds and 2.10 (Hard-SLP), it alos not work for flash rom, display error[260] at final.
Do you have admin rights onyour machine? Also if you dont try with Force SSPL option. I get that error form work when I am not logged in as admin.
were are you stuck? if your stuck in bootloader or splash, look here
If you can still boot to OS, try to flash HardSplv7. if this is successfull, try to flash the new wm6, instead of using autodetect, click spl2.10, and check "is it hard spl?".
good luck!
sorry, I am not stuck on my Hermes, it´s all good, but it won´t flash anything and yes, I have admin rights on XP. I´ve got IPL 1.00, SPL 1.13.Oli. I´d really like to update to a newer version of WM6 but I can´t. I even tried with force SSPL and even the HERMimg.nbh flashing method from card didn´t work.
What I can do off course is booting into WM6, but my WM6 version is a quite old one
PS: Troubleshooting info: When I try to flash HardSPLv7, my device is going into Tricolor mode (like it should) showing IPL-SSPL by Des and SPL-1.09.ds and XP hardware assistant is searching for drivers for an unknown USB device and after a while I´ll get the error260 :/
are you up to date on your .net framework? 3.0?
framework 3.0? no, I think I have 2.0, but thanks for the tip. But my problem is now solved I formatted my micro SD to FAT32 and that helped flashing directly from card. After that I tried flashing via USB and now that also works!
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe
Hello, I am in serious trouble! I got a brand new HTC Athena with Windows Mobile 5.0. I succesfully upgrade it to Windows Mobile 6.0.
All was OK.
Than I was interested to move into Windows Mobile 6.1 and possibly 6.5. At first I did the Athena unlock (3 step process) and all went OK: Antenna 1.5.0, SPL 1.2 OLI....
THAN I DID MY ERROR! I try to upgrade my 6.0 ROM with the Micky 6.1 cooked file with SPL 3.5. After a 92 percent upgrade, the ROM crashed and now I always get a nasty black screen with few lines (No 3 color bands!). When I try to upgrade again the same ROM or ROM for SPL 1.2 I get an error (ID mismatching). I guess the only solution is a hard and full reset of the Windows. But doing only a hard reset with the PDA will NOT change my error message and I will keep see this nasty black screen and I cannot load the Windows ActiveSync application-
I am totally lost. Help please. Any tool for a true full restore/recover??? (I did NOT make any backup!).
This thread might hold a solution to your problem.
Hi
If you follow the instructions exactly in post 33, it will solve your problems. just click HERE
Jay
Hello, those links are basically for corrupted wifi antenna files.-
In my case my HTC Athena crashed the Windows 6 ROM while I was attempting to upgrade, after unlocking the phone, the Athena from version 6.0 to version 6.1
Are you sure I can use the post #33 also for my specific trouble?
Thank you in advance!
this is also to repair your bootloader-infos
if you look at your bootloaderscreen, you will see ATHE100, IPL, ATHE100, SPL. if not, you have to repair it
make sure you flashed the right rom, spl 1 or 3.5
How can the bootloader get repaired?
yes use that link, post #33. fixes both wifi and modelid problems and bootloader problems when you got stuck at 92% of the flashing process.
Cannot re flash ROM
Please help! I tried the unlocker and it failed at 92% and since then I have no WM6. Then I tried to flash the Michy WM6.5 and that failed. I was getting model id errors so I did the mtty and mac1 fix which was succesful. However all I can get now is a grey screen on boot-up. I can get to the bootloader screen and it displays ATHE100, IPL-v2.02, ATHE100, SPL-v1.20. Olipro. From what I have read on the forum at this stage I should run a RUU to flash a WM6 ROM but all that I try can't connect because no OS running to connect with Activesync? Is there a way to flash from the bootloader? The other option seems to be putting an image and flasher on a miniSD but I can't find clear instructions for this or which files?
Please ignore - my battery wasn't charged enough. Replaced battery and recovered device.
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
I have follow the link (thread 33)...., however, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
first, how can I get the mac address of my device? It is NOT written anywhere in the Athena parts (checked in the battery bay and so on.....), and so when I run mtty i am in trouble! I have used a mac address got from my company's manager, but not sure it is ok to use it with the Athena!
Anyway,......I have follow the post link (thread 33)...., and followed the various steps.- However, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Solved!
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
puffo said:
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
Click to expand...
Click to collapse
Can you tell what you've actually done after you've changed ROM with Mtty?
I done the thing with Mtty but just as you described when I reset it now I still get the grey screen. And if I try to update ROM it fails again on 92%
where did you find the upgrade from wm5 to wm6?
the link I found on rapidshare seems not be availabel anymore
I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.