Hi,
I want to upgrade the OS on my T-Mobile MDA-2. To do this I press the power button and hit the reset button while I keep the power button pressed. Instead of starting the bootloader screen the phone does a hard reset and reinitalizes the current image....
Any advice anyone?
Thanks,
Oliver
Dude said:
Hi,
I want to upgrade the OS on my T-Mobile MDA-2. To do this I press the power button and hit the reset button while I keep the power button pressed. Instead of starting the bootloader screen the phone does a hard reset and reinitalizes the current image....
Any advice anyone?
Thanks,
Oliver
Click to expand...
Click to collapse
Are you going to upgrade OS using SD card? If so, you need to press the cursor key in any direction with Power button and reset button pressed too...
If using USB cradle, just put MDA2 to cradle and run upgrade...
Related
Hi!
Please help, after a bad update my MDAII does not boot!
On the Display after cold boot: NO GSM
D 1.03.00 GER
I read, that it´s posible to boot from SD-CARD.
But where i can get a working image for my SD Card.
How does it works exactly ?
Thanks
Steve
that means that the radio update failed.
if you boot your device into bootloader mode ( press power + action key simultanuously, while resetting )
put it in it's cradle,
your screen should say 'USB' on the top, and '1.06' ( or another version ) on the bottom.
and run the upgrade again.
after about 2-3 minutes the upgrade will start again.
Thans for the fast reply!
I try it but it wont work :-(
Power button + Action Key & Reset
Witch action key you mean? I tryed the button under the Power button.
Steve
steve2000 said:
Thans for the fast reply!
I try it but it wont work :-(
Power button + Action Key & Reset
Witch action key you mean? I tryed the button under the Power button.
Steve
Click to expand...
Click to collapse
Nope, action key is meant to be the four ways key! The key between the red and green button! You have to press that in the middle! That's the action key.
HEHE!
Thanks alot !!!!! -- it works !
Steve
I can not put my your hermes into bootloader mode (side ok + power button + softreset) to check out the SPL version. Is there other possibility to flash a new ROM?
I bouth an used Vario II (Herm300) with boot problems, the PDA is booting until this screen (picture) and than after 10 second it reset by itself. After the Reset the PDA boot again the same screen.
Had someone similar problems ?
Thanks.
To enter bootloader mode you have to press Ok + Power button only without Soft Reset
0xff.0xff said:
To enter bootloader mode you have to press Ok + Power button only without Soft Reset
Click to expand...
Click to collapse
ummm, wrong. You hold power + side OK then reset with stylys and keep holding the power and side OK, you should enter boot mode at which point you can let go of the two buttons.
eagercrow said:
ummm, wrong. You hold power + side OK then reset with stylys and keep holding the power and side OK, you should enter boot mode at which point you can let go of the two buttons.
Click to expand...
Click to collapse
Oh, sorry, your truth... you don't have to press soft reset only if device is switched off... sorry for confusion
hi
my htc s740 is dead...
How to a hard reset with the keyboard?
when I press power button the ppc it blocks at written "windows mobile 6.1", if I attend some minute, it exits to me outside a shielded white screen whit this word: "the device is unable to boot because either you have turned off the device incorrectly or tried to install an application from untrusted source.Press SEND to reset your device or press any other button to cancel. This operation will delete all your personal data and restore the device to its factory default settings.
if I press SEND key it does not succeed nothing
while off, press and hold vol down and center nav key, then power button.
ombre33 said:
while off, press and hold vol down and center nav key, then power button.
Click to expand...
Click to collapse
great!!is ok! thanks.....
ombre33 said:
while off, press and hold vol down and center nav key, then power button.
Click to expand...
Click to collapse
hey m8!
Thanks for the solution. i had hardtime doing it thou!!! if you encounter problems. press and hold vol down and center nav key BUT when it comes to power; just dot it. anyway maybe it's just me who did the stupid thing of holding power (well it works for the diamond so i thought...)
anyway thanks goes to ombre33
HTS Rose
R.0.24.30.24
G.12.23.30.06W
D.1.14.00.00
Peace
V
Does not work for me...
My Rose Keyb is not responding, I changed something in the registry and now I can no longer use both Keyb, I remove the battery, try the hard reset button stuff does not work, any ideas ?
sorry edit
ombre33 said:
while off, press and hold vol down and center nav key, then power button.
Click to expand...
Click to collapse
thnx! it works!
Strange.
Very strange! After doing the procedures, the rose ask to do the reboot and stop in logo of HTC. I had never happened me in any pda.
Now what i do?
You have to wait about 4-5 minutes then Rose will reboot again and will install the additional software.
1. From the Home screen, press the Start button.
2. Press More
3. Select Accessories
4. Select Clear Storage
5. You will be prompted to enter a code, enter 1234
I had the same probleem, my HTC S740 freezes after reboot with the HTC logo screen. I tried the follwoing and it worked:
- press and hold vol down and the navigation key
- pres and release directly the power botton
- a messege will apear, press the navigation key.
- the device will reset to factory settings
- a messege appear asking to press vol up to restart
- device will restart and begin reinstalling the software, reboot after then.
May i ask what are the applications (that came installed with the phone) that are gone with the hard resetting ?
Thanks
HTC s740 backup before reset
hi...i would like to know if there is anything one can do to back the information up before resetting the Phone as i have crucial Data i cant affort to loose. PLS HELP!?
There are few backup softwares which can backup almost everything on your phone, and you can easily recover it after hard reset. I personally use Sprite Backup, which is probably the best one.
HI. I apologize for my english.
I'am searching from 2 days a method to return to a stock rom. Now the OS doesn't work and my phone boot directly to bootloader. I bought the phone that was used and inside it was the nextgen rom(this phone is bought from amazon but i don't know if it's branded). now i don't know what i did but i'm blocked to bootloader. I have fear to brick my phone.
PD67100 SS-BC(4K)
SPL-1.30.2250.1(117833)
MicroP(LED) 0x07
Touch C1(v69)
Can you help me?? i'm going crazy!!!
hi,
just checking- did you try taking the battery out, waiting 10 seconds, putting battery in and starting the phone?
you can also try hard reset-
1. Press Volume up button and hold then press Volume Down button and hold and then press the power button (briefly) to switch the phone on.
2. Keep holding the volume up and volume down buttons until you see a reset screen option.
3. Now follow the instructions that will show up on your mobile screen to factory reset your phone.
if it works dont forget to hit the thanks button!
Hi,
I want to change my custom rom, but for whatever reason I can't get into bootloader...
I can get into usb mode with ease... But not into bootloader.
pressing the + volume and - volume at the same time and pressing/holding the power button just makes my Titan go into a loop...
If I keep hold of both the powerbuttons but only press the powerbutton once, then the Titan just starts up.
What am I doing wrong here?
Come on guys, help me out here.
What you have to do is hold + and - volume button and shortly press power button. Do not keep pushing power button because that is what causes the continuous loop. Keep pressing the volume buttons until the bootloader screen appears and then connect you usb-cable.
malvo26 said:
What you have to do is hold + and - volume button and shortly press power button. Do not keep pushing power button because that is what causes the continuous loop. Keep pressing the volume buttons until the bootloader screen appears and then connect you usb-cable.
Click to expand...
Click to collapse
Thanks, but I doesn't work for me...
If I press the power shortly, it will just start up...
It's like the volume up doesn't respond, although it does when the phone is on...
I say that because pressing the camera button and volume down does work, and gets me into USB Mode
gremsems said:
Thanks, but I doesn't work for me...
If I press the power shortly, it will just start up...
It's like the volume up doesn't respond, although it does when the phone is on...
I say that because pressing the camera button and volume down does work, and gets me into USB Mode
Click to expand...
Click to collapse
Have no idea what went wrong with your phone. But I would try to flash HSPL again (with SPL goldcard) and if that does not work - I would try to flash stock (also with goldcard). But if the bootloader is somehow really damaged (somehow physically) - then you lose the ability to flash customs in future.
For now you are able to do it at least via goldcard.