Hello,
I tried to upgrade my imate with bluetooth (instead of cable, because it is in my job)and now the only thing i see in the screen is "Serial v1.02" I have tried to do a full reset but nothing changes. What can i do??? Thanksss
:lol: not buy serial cable!!!
there is an OFFICIAL UPGRADE ready and existing, but not yet PUBLIC,
it is one nice 40 MB RUU file which will uprgade your unit to english language:
Microsoft Pocket PC version 4.20.0 (Build 13252)
ROM version: 1.60.00WWE
ROM date: 12/03/03
Radio version: 1.06.01
Protocol version: 1337.16
ExtROM version: 1.60.06
Indirizzo http://xda-developers.com/incoming/rom160wwe/RUU16006WWE_T-mobile_NL.exe
IT'S FANTASTIC AND EASY WHIT THE USB CRADDLE
What you may try to do, for a start, is to reinstall the ROM upgrade once again, USING THE USB CRADLE and nothing else. Better remove the SIM card before installing the upgrade. Also, make sure that the battery is fully charged. All through the upgrade process, do not touch the device.
Finally....
Next day When i was in my job put my imate in the cradle, ran the upgrade and it worked.....I am happpppppy ¡¡¡¡
Upgrade failed
I had the same problem as dherrero. However, I have no luck as him. My XDA II still dead can not be boot. Anyone can help? Thanks.
IT's DEAD
I have a MDA from T-Mobile for 3 weeks now. I find out about the rom update (RUU16006WWE_T-mobile_NL.exe), tried it and got the message that the update failed.
On my MDA screen therse is only the message "USB v1.01".
Running the update again doesn't help.
Is there a solution or do I have to contact T-Mobile?
Hi all ,
One of my Friends had the same problem , he tried another computer and it works , then guess what was the problem ???? We found that it was ZONE ALARM !!!
So please check You'r computers guyes ,it might be another software makes the upgrade failed .
Thanks
Hi all!
We have to be aware, that the upgrade program says "NO PROGRAMS RUNNING ON THE PPC AND NO PROGRAMS RUNNING ON THE PC ITSELF"
It's a hard lesson i learned years ago while flashing a BIOS..... if possible, do it at an UPS equipped PC (or notebook btw) to reduce your chances of killing your device.
Windows XP has many more programs running than one would suspect. As a first measure, kill all the ones you can in the right side of your taskbar, shut down your Anti Virus and Firewall, and cross your fingers while upgrading.....
Should we also shut down Activesync? Or is it needed for the upgrade?
Thanx.
I am in the same boat this day. Please help !!! I tried to upgrade the imate threw the club imate ... i downloaded ok i believe ... i did not use the cradel just a mini sync usb cord ... i used this before many times to sync... but when i tried to run the official update it stopped and now it says only serial v1.02 when i put it in the cradel it says usb v1.o2 its dead... no light for batter scharge nothing???? no sync at all please help
ActiveSync is not involved in the upgrade process. The upgrade program runs out of this, with it's own connection and settings via USB.
I haven't used the mini cord, so I'm of no help about it.
Try the upgrade program again, looks like it failed to fully flash your ROM. (That's why you don't see the charging light, it's Software controlled)
Good Luck!
mm
Try to update your imate using a cradle connected to a pc(usb). It should work
i have the exact same problem as highlighted by the others here, USB and v1.02 screen. Question is, how do you continue to flash your rom after it fails and you put back your unit into the cradle and activesync does not sync it anymore
the upgrade doesnt use activesync so it doesnt matter. Just put the imate in the cradle(in other pc, if possible) and run the upgrade
qtek rom update problem
hi guys. my qtek only says USB v 1.02. I cannot do any rom flash. what rom should i use. where can i download it from?
hai all, i had upgrade my wm5.0 to Black 3.0 successfully, downgraded back to wm5.0 and intend to upgrade to dutty wm6.0.
when i intended to upgrade again, the upgrade tool prompt me "unknown device, please check you cradle or usb connection". i had checked i can syn with my active syn 4.5. i can move files from my notebook to my htc hermes and vice verse.
i tried numerous time to upgrade from wm 5.0 to many various wm6.0 but still being prompt with the same message.
any advice and guidance would be very much appreciated. Thanks
ohh yeah one more error message i got, "unknown version, you should pick sspl"
problem solved
weird, after i had installed and run the SIM & CID unlocker, i can upgrade to wm6.0.
previously before this issue appear, i still can upgrade to wm6.0(black version) from stock condition.
anyway case close. This place rock
Here's the deal: I need help!!!!!!
I have a HTC TYTN and upgraded it's ROM from WM5 to Custels Ultimate WM6 as he got a lot of good reviews for it. However, there's a bug in it - apparently a bug Mr. Custel was aware of. After upgrading to WM6 my Active sync does no longer work when using USB.
Here's my details:
HERM200
spl-2.10 Olipro
IPL-1.04
Windows Mobile 6 Professional
CE OS 5.2.1238 (Build 17745.0.2.3)
ROM Version: CUSTEL Ultimate
ROM Date: 05/05/07
Radio version: 1.41.00.10
Protocol version: 32.74.7020.18H
I run Active sync 4.5 on my PC.
I have checked that the setting for Active sync is correct on my computer and that the 'Enable advanced network functionality' box is unchecked in the USB-to-Pc setting on my TYTN
I have tried to manually put my TYTN into Bootload to see if it can connect via USB then - and it cannot even if it says USB on my TYTN tricolor screen.
I've deactivated firewall, checked to see if settings for Outlook is correct etc... etc...
I've even tried to put a .nbh file on my SD card and put TYTN into Bootload mode - but it never got past the tricolor screen.....
In other word: I cannot connect my TYTN to my PC and I cannot flash another ROM onto my TYTN to make it work properly with Active sync.
What can I do? Any ideas would be appreciated.
Regards,
Njål
I will try
Well I had the same problem with active sync when I installed wm6 on my cingular 8525 (hermes). Once I figured out to remove the check in the USB to PC window, I removed activesync 4.5 and restarted my pc. Then I reinstalled activesync. I then restarted my pc. I then hooked the usb cable from the cradle that my phone sits in and then placed the phone in the cradle. Everything has worked fine since then. I know for sure that check in USB to PC has to be unchecked. It will not work unless. So try that and see what happens. That is what I had to do. It would not work until I unistalled and reinstalled activesync. Hope this helps.
A little more info:
Here's a little more info when it comes to my problem.
I've read the thread regarding Mr Custel's WM6 Final ROM and after I upgraded my phone, several others has complained about the same problem as I have.
Mr Custel has written that he's aware of the problem and that he will fix it - however, I now see a new ROM upgrade from Mr Custel called Custels Ultimate WM6 ROM. The problem is that I cannot install it since I cannot get an USB connection to work.
I've tried uninstalling Active sync - restart PC - reinstall active sync - restart PC and try to connect. Several times, actually. It doesn't work
Any ideas?
Regards, Njål
I am upgrading here:
http://forum.xda-developers.com/showthread.php?t=352221
Iam using Vista x32 Ultimate which has a built in Active Sync.
I dumped the content of that rar into C:\Windows\Temp and proceed to update when i plugged in my phone.
Then i wait and then it goes "Target Not found" and window crashes
Now my phone is stuck in a black mode that says:
Update Utility
USB Connected
And when i try to rerun the Device Utility Update it says: Error: CONNECTION ERROR
What do i do now?
HELP??????? Who can i contact? I have got a window xp computer now
Set it to Tricolor screen, and ran the original factory shipped ROM hope it can override the bad ROM image. It worked with Prophet and Kaiser.
I have not played with my AtomExec for so long, so I am really rusty with it now. Borrow or use a machine with Windows XP and installed ActiveSync and see if you can do it with that.
It is going to be a lot of work but it is better than a dead AtomExec.
Because very few people actually bought AtomExec so the general help is not that much around. I just received an Email from O2 that the company is taken over by another group.
I just update my AtomExec to WM6, still testing it.
I'm a real noob at all this as I have only had my Dopod 838 Pro for about 2 months. I want to upgrade to WM6.1 but first I'm trying to install HardSPL just in case something goes wrong.
When I run RUUWrapper.exe everything goes OK until the programs starts trying to connect to my phone. It just times out and gives me an error 260 message. The phone is connected fine and it syncs perfectly. I'm running windows vista ultimate and have the latest WMDC installed.
Never mind. For some reason it has fixed itself and has now flashed fine. Sorry everyone. I look forward to hanging around here more often.
Try the Sd card method, NO sync problems or accidents waiting to happen... I don't use the pc to flash anymore, EVER...
Cheers...